JL Audio A2150 User Manual

Size:
495.43 Kb
Download

A2150

two-channelfull-rangeamplifier

OWNER’S MANUAL

Thank you for purchasing a JL Audio amplifier for your automotive sound system.

Your amplifier has been designed and manufactured to exacting standards in order to ensure years of musical enjoyment in your vehicle. For maximum performance and extended warranty

coverage, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized

dealer has the training, expertise and installation equipment to ensure optimum performance from this product. Should you

decide to install the amplifier yourself, please take the time to read this manual thoroughly so as to familiarize yourself with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance,

please call the JL Audio Technical Support Department at (954) 443-1100during business hours.

PROTECT YOUR HEARING!

We value you as a long-termcustomer. For that reason, we urge you to practice restraint in the operation of this product so as not to damage your hearing and that of others in your vehicle. Studies have shown that continuous exposure to high sound pressure levels can lead to permanent (irreparable) hearing loss. This and all otherhigh-poweramplifiers are capable of producing such high sound pressure levels when connected to a speaker system. Please limit your continuous exposure to high volume levels.

While driving, operate your audio system in a manner that still allows you to hear necessary noises to operate your vehicle safely (horns, sirens, etc.).

SERIAL NUMBER

In the event that your amplifier requires service or is ever stolen, you will need to have a record of the product’s serial number. Please take the time to enter that number in the space

provided below. The serial number can be found on the bottom panel of the amplifier and on the amplifier packaging.

Serial Number:

INSTALLATION APPLICATIONS

This amplifier is designed for operation in vehicles with 12 volt, negative-groundelectrical systems. Use of this product in vehicles with positive ground and/or voltages other than 12V may result in damage to the product and will void the warranty.

This product is not certified or approved for use in aircraft.

Do not attempt to “bridge” the outputs of this amplifier with the outputs of a second amplifier, including an identical one.

Chassis Ground

Connector

(pg. 5)

+12 V Power

Remote Turn-On

Connector

Connector

(pg. 5)

(pg. 6)

Input Voltage

 

Left & Right

Protection Status

Bass EQ

Filter Mode

Selection

Preamp Output Jacks

Indicator

 

On/O Switch

Selection

(pg. 6)

 

(pg. 8)

 

(pg. 9)

Jack for

(pg. 8)

 

(pg. 7)

 

 

Power Status

 

Input Sensitivity

Filter

 

Left & Right

Remote Bass

 

Preamp Input Jacks

Indicator

 

Control Knob

 

Control

Frequency Selector

 

(pg. 6)

 

(pg. 9)

 

(pg. 8)

 

(pg. 6)

(pg. 7)

PLANNING YOUR INSTALLATION

It is important that you take the time to read this manual and that you plan out your installation carefully. The following are some considerations that you must take into account when planning your installation.

Cooling Efficiency Considerations:

The outer shell of your JL Audio amplifier is designed to remove heat from the amplifier circuitry. For optimum cooling performance, this outer shell should be exposed to as large a

volume of air as possible. Enclosing the amplifier in a small, poorly ventilated chamber can

lead to excessive heat build-upand degraded performance. If an installation calls for an enclosure around the amplifier, we recommend that this enclosure be ventilated with the aid of a fan. In normal applications,fan-cooling

is not necessary.

Speaker Outputs

(pg. 8)

Mounting the amplifier upside down is strongly discouraged.

If mounting the amplifier under a seat, make sure there is at least 1 inch (2.5 cm) of space above the amplifier’s outer shell to permit proper cooling.

Safety Considerations:

Your amplifier needs to be installed in a dry, well-ventilatedenvironment and in a manner which does not interfere with your vehicle’s safety equipment (air bags, seat belt systems, ABS brake systems, etc.). You should also take the time to securely mount the amplifier using the supplied screws so that it does not come loose in the event of a collision or a sudden jolt to the vehicle.

Stupid Mistakes to Avoid

Check before drilling any holes in your vehicle to make sure that you will not be drilling through a gas tank, brake line, wiring harness or other vital vehicle system.

Do not run system wiring outside or underneath the vehicle. This is an extremely dangerous practice which can result in severe damage to your vehicle and person.

Protect all system wires from sharp metal edges and wear by carefully routing them, tying them down and using grommets and loom where appropriate.

Do not mount the amplifier in the engine compartment, under the vehicle, on the roof or in any other area that will expose the amplifier circuitry to the elements.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

JL AUDIO A2150

JL AUDIO A2150

3

PRODUCT DESCRIPTION

The JL Audio A2150 is a two-channelfull-rangeaudio amplifier utilizing patented Absolute Symmetry™ Class A/B technology for both channels.

The A2150 can be operated with a wide variety of source units and system configurations.

TYPICAL INSTALLATION SEQUENCE

The following represents the sequence for a typical amplifier installation, using an aftermarket source unit or OEM Interface processor (like the CleanSweep CL441dsp).

Additional steps and different procedures may be required in some applications. If you have any questions, please contact your authorized JL Audio dealer for assistance.

1)Disconnect the negative battery post connection and secure the disconnected cable to prevent accidental re-connectionduring installation.This step is not optional.

2)Run power wire (minimum 8 AWG) from the battery location to the amplifier mounting location, taking care to route it in such a

way that it will not be damaged and will not interfere with vehicle operation. Use 4 AWG or larger power wire and a power distribution block if additional amplifiers are being installed with the A2150.

3)Connect power wire to the positive battery post. Fuse the wire with an appropriate fuse block (and connectors) within 18 inches (45 cm) wire length of the positive battery post.

This fuse is essential to protect the vehicle. Do not install the fuse until the power wire has been securely connected to the amplifier.

4)Run signal cables and remote turn-onwire from the source unit to the final amplifier mounting location.

5)Run speaker cables from the speaker systems to the amplifier mounting location.

6)Find a good, solid metal grounding point close to the amplifier and connect the negative power wire to it using appropriate hardware (use of the JL Audio ECS master ground lug, XA-MGL-1is recommended). Use the same size power wire as the wire connected to the “+12VDC” connection (minimum 8 AWG), no longer than 36 inches

(90 cm) from the amplifier to the ground connection point. In some vehicles, it may be necessary to upgrade the battery ground wire. (See page 5 for important notice).

7)Securely mount the amplifier using the supplied screws.

8)Connect the positive and negative power wires to the amplifier. A fuse near the amplifier is not necessary.

9)Connect the remote turn-onwire to the amplifier.

10)Connect the input cables to the amplifier.

11)Connect the speaker cables to the amplifier.

12)Carefully review the amplifier’s control settings to make sure that they are set according to the needs of the system.

13)Install the power wire fuse (20A for a single A2150) and reconnect the negative battery post terminal.

14)Turn on the source unit at a low level to double-checkthat the amplifier is

configured correctly. Resist the temptation to crank it up until you have verified the control settings.

15) Make necessary adjustments to the input sensitivity controls to obtain the right overall output and the desired balance in the system. See Appendix A (page 12) for the recommended input sensitivity setting method.

16)Enjoy the fruits of your labor with your favorite music.

POWER CONNECTIONS

Before installing the amplifier, disconnect the negative (ground) wire from the vehicle’s battery. This will prevent accidental damage to the system, the vehicle and your body during installation.

4

JL AUDIO A2150

The A2150’s “+12VDC” and “Ground” connections are designed to accept 8 AWG -

4 AWG power wire. 8 AWG is a minimum power wire size for this amplifier.

If you are installing the A2150 with other amplifiers and wish to use a single main power wire, use 4 AWG or larger main power wire (depending on the overall current demands of all the amplifiers in the system). This 4 AWG or larger power wire should terminate into a distribution block mounted as close to the amplifiers as possible and should connect to the A2150 with 8 AWG - 4 AWG power wire.

Note: that smaller AWG numbers mean bigger wire andvice-versa(1/0 AWG is the largest, 2 AWG is smaller, then 4 AWG, then

8 AWG, etc.).

To connect the power wires to the amplifier, first back out the set screw on the top of the terminal block, using the supplied 2.5 mm hex wrench. Strip 1/2 inch (12 mm) of insulation from the end of each wire and insert the bare wire into the terminal block, seating it firmly so that no bare wire is exposed. While holding the wire in place, tighten the set screw firmly, taking care not to strip the head of the screw.

The ground connection should be made using the same gauge wire as the power connection and should be kept as short as possible, while accessing a solid piece of sheet metal in the vehicle. The surface of the sheet metal should be sanded at the contact point to create a clean, metal-to-metalconnection between the chassis and the termination of the ground wire. For optimal grounding, we recommend the use of a JL Audio ECS master ground lug(XA-MGL-1).Alternatively, a sheet metal screw or bolt can be used with a star washer.

Any wires run through metal barriers (such as firewalls), must be protected with a high quality rubber grommet to prevent damage to the insulation of the wire. Failure to do so may result in a dangerous short circuit.

Many vehicles employ small (10 AWG - 6 AWG) wire to ground the battery to the

vehicle chassis and to connect the alternator’s positive connection to the battery. To prevent voltage drops, these wires should be upgraded to 4 AWG when installing amplifier systems with main fuse ratings above 60A.

FUSE REQUIREMENTS

It is absolutely vital that the main power wire(s) to the amplifier(s) in the system be fused within 18 inches (45 cm) of the positive battery post connection. The fuse value at each power wire should be high enough for all of the equipment being run from that power wire. If

only the A2150 is being run from that power wire, we recommend a 20A fuse be used. AFS (mini blade fuse), AGU (big glass fuse) or MaxiFuse™ (big plastic-bodyfuse) types are recommended.

No fuse is required or recommended directly before the amplifier power connection. If one is desired, we recommend the use of a 20A.

TURN-ONLEAD

The A2150 uses a conventional +12V remote turn-onlead, typically controlled by the source unit’s remoteturn-onoutput. The amplifier will turn on when +12V is present at its “Remote” input and turn off when +12V is switched off.

If a source unit does not have a dedicated remote turn-onoutput, the amplifier’sturn-onlead can be connected to +12V via a switch that derives power from anignition-switchedcircuit.

The A2150’s “Remoteturn-onconnector is designed to accept 18 AWG – 12 AWG wire. To connect the remoteturn-onwire to the amplifier, first back out the set screw on the top of the terminal block, using the supplied 2.5mm hex wrench. Strip 1/2 inch (12mm) of wire and insert the bare wire into the terminal block, seating it firmly so that no bare wire is exposed. While holding the wire in the terminal, tighten the set screw firmly, taking care not to strip the head

of the screw and making sure that the wire (not the insulation) is firmly gripped by the set screw.

JL AUDIO A2150

5

INPUT SECTION

The A2150’s input section allows you to send signal to the amplifier section through the use of two differential-balancedinputs, one for

the left channel and one for the right channel. Connection is via RCA-typejacks.

Input Voltage Range:

A wide range of signal input voltages can be accommodated by the A2150’s input section (200mV – 8V). This wide range is split up into two sub-ranges,accessible via a switch located to the left of the Input Connectors.

The “Low” position on the “Input Voltage” switch selects an input sensitivity range between 200mV and 2V. This means that the “Input Sens.” rotary control will operate within that voltage window. If you are using an aftermarket source unit or an OEM interface processor with conventionalpreamp-leveloutputs, this is most likely the position that you will use.

The “High” position on the “Input Voltage” switch selects an input sensitivity range between 800mV and 8V. This is useful for certain highoutput preamp level signals as well as speakerlevel output from source units and

small amplifiers.

To use speaker-levelsources, splice the speaker output wires of the source unit or small amplifier onto a pair of RCA plugs. No line output converter is needed in most cases.

The output of the amplifier will decrease for a given input voltage when the “Input Range” switch is placed in the “High” position.

Conversely, the output will be higher with the switch in the “Low” position. While this may sound counter-intuitive,it is consistent with the descriptions above.

INPUT SENSITIVITY CONTROL

Once the appropriate “Input Voltage” range has been selected, the control labeled “Input Sens.” located in the “Amplifier Controls” section can be used to match the source unit’s output voltage to the input stage of the amplifier for maximum clean output. Rotating the control clockwise will result in higher sensitivity (louder for a given input voltage). Rotating the controlcounter-clockwisewill result in lower sensitivity (quieter for a given input voltage.)

To properly set the amplifier for maximum clean output, please refer to Appendix A (page 12) in this manual. After using this procedure, you can then adjust any or all “Input Sens.” levels downward if this is required to achieve the desired system balance.

Do not increase any “Input Sens.” setting for any channel(s) of any amplifier in the system beyond the maximum level established during the procedure outlined in Appendix A (page 12). Doing so will result in audible distortion and possible speaker damage.

FILTER CONTROLS

Most speakers are not designed to reproduce the full range of frequencies audible by the human ear. For this reason, most speaker systems are comprised of multiple speakers, each dedicated to reproducing a specific frequency range. Filters are used to select which frequency range is sent to each section of a speaker system. The division of frequency ranges to different speakers can be done with passive filters (coils and/or capacitors between the amplifier outputs and the speakers), which are acceptable and commonly used for filtering between midrange speakers and tweeters. Filtering between subwoofer systems and satellite speaker systems is best done with active filters, which cut off frequency content at the input to the amplifier. Active filters are more stable than passive filters and do not introduce extraneous resistance, which can degrade subwoofer performance.

The active filter built into the A2150 can be used to eliminate potentially harmful and/or undesired frequencies from making their way through the amplifier sections to the speaker(s). This serves to improve tonal balance and to avoid distortion and possible speaker failure. Correct use of these filters can substantially increase the longevity and fidelity of your audio system.

1)“Filter Mode” Control: The A2150 employs a 12dB per octave filter which can be configured into one of two filter types or defeated completely by way of the three-position “Filter Mode”switch:

“Off”: Defeats the filter completely, allowing the full range of frequencies present at the inputs to feed the amplifier. This is useful

for systems utilizing outboard crossovers or requiring full-rangereproduction from the A2150’s channels.

“LP” (Low-Pass): Configures the filter to attenuate frequencies above the selected filter frequency at a rate of 12dB per octave. This is useful for connection of subwoofer(s) to the A2150’s in abi-amplifiedsystem.

“HP” (High-Pass): Configures the filter to attenuate frequencies below the selected filter frequency at a rate of 12dB per octave. This is useful for connection of component speakers to the A2150’s channels in abi-amplifiedsystem.

2)“Filter Freq. (Hz)” The filter frequency markings surrounding this rotary control are for reference purposes and are generally accurate to within 1/3 octave or better. If you would like to select the filter cutoff frequency with a higher level of precision, consult the chart in Appendix B (page 13).

Tuning Hint: If you are using the A2150 to drive a subwoofer system (“LPmode), a component satellite speaker system (“HPmode) or both,

80 Hz is a good baseline “Filter Freq. (Hz)” setting. After properly adjusting the “Input Sens.”, as outlined in Appendix A (page 12), you can fine tune the “Filter Freq. (Hz)” control to achieve the desired system frequency response.

6

JL AUDIO A2150

JL AUDIO A2150

7

BASS BOOST CONTROLS

1)“Bass Boost”: This switch allows the user to activate a 6 dB boost centered at 48 Hz.

When the “Bass Boost” is activated, the inputs to “CH 1 (Left)” and “CH 2 (Right)” are summed to create a mono signal. The “Filter Mode” switch in the “Channel 1 & 2” section must be in the “LP” position for the bass boost to be functional.

2)Remote Bass Port: This port allows you to connect an optional remote boost knob (sold separately as JL Audio ModelRBC-1)that can be mounted in the front of the vehicle. With theRBC-1connected, the boost is no longer limited to 0 or +6 dB, allowing a variable range of 0 to +12 dB of boost to be selected.

PRE-OUTS

The A2150 incorporates a pass-throughpreamp output section, so that additional amplifiers can be easily added to the system. The preamp output delivers the same signal that is connected to the A2150’s inputs.

The preamp output signal is not affected by the “Bass Boost” processing selected for the amplifier or by any crossover filter selected (if the input signal isfull-range,the preamp output will befull-range).

The signal level of the “Preamp Output” isline-level(low voltage), regardless of the position selected in the A2150’s “Input Voltage” switch. An additional amplifier connected to these preamp outputs should have its input voltage switch set to the “Low” position.

SPEAKER OUTPUTS

The A2150’s speaker outputs are designed to accept 16 AWG - 8 AWG wire.

The A2150 is designed to deliver power into speaker loads equal to or greater than 2 ohms when using a “stereo” configuration and speaker loads equal to or greater than 4 ohms when using a “bridged” configuration.

Speaker loads below 2 ohms nominal per channel in stereo or below 4 ohms nominal bridged mono are not recommended and may cause the amplifier to initiate a protection mode which reduces power output.

BRIDGING CONSIDERATIONS

Bridging is the practice of combining the output of two amplifier channels to drive a single load. When bridged, each channel produces signals of equal magnitude, but opposite polarity. The combined output of the two channels provides twice the output voltage available from a single channel. The A2150 has been designed for bridging of its channels without the need for input inversion adaptors.

To bridge the A2150’s two channels, use the “CHANNEL 1 +” and “CHANNEL 2 speaker connectors only (the “CHANNEL 1 and “CHANNEL 2 +” remain unused). When bridged, the A2150 will deliver optimum power into a 4 ohm load.

When a pair of channels are bridged, they will deliver 150W x 1 into a 4 ohm load or 90W x 1 into an 8 ohm load. Operating a pair of bridged channels into a load lower than 4 ohms is not recommended.

Because a bridged pair of channels requires that both channels receive input, you need to connect both left and right inputs to the source unit. Connection of only one input will result in reduced power output, increased distortion and can cause the amplifier to overheat.

Do not do this!

When the A2150 operating in bridged mode, the output will be in mono (only one channel). This mono channel can contain right channel only information, left channel only information or the sum of the information from both the right and left channels. In order to achieve one of these options, configure the inputs to that pair of channels in one of these two ways:

1)Left Channel Only or Right Channel Only Information: If you wish to send a left-only or right-only signal the A2150, use a “Y-Adaptor” to split the single channel signal into both left and right RCA inputs. This option is useful when using one A2150 to drive left channel speakers only and the other A2150’s channels to drive right channel speakers only.

2)Left + Right Channel Information:

When bridged and fed by a stereo input, the A2150’s channels will automatically combine the left and right channels into a summed mono (left + right) channel. This option is useful when using the A2150 channels to drive a subwoofer system or a summed mono center channel.

AMPLIFIER STATUS INDICATOR LIGHTS & PROTECTION CIRCUITRY

There are two status indicator lights on the input / control end of the amplifier.

1)“Power” (Green): lights to indicate that the amplifier is turned on and operating normally.

2)“Protect” (Red): Indicates that the amplifier protection circuitry has been activated to prevent product failure due to ashort-circuitor a dangerously low impedance connected to the amplifier output(s). Connecting the speaker outputs to an impedance lower than 2 ohms stereo (4 ohms bridged) will cause this protection mode to activate. When this

protection mode is activated, the amplifier will reduce it maximum power output to protect its circuitry, which will manifest itself as increased distortion. When the problem is corrected, the amplifier will return to normal operation.

Advanced Rollback Thermal protection

Unlike conventional thermal protection systems, which shut down an amplifier when it overheats, this system protects the amplifier by gradually reducing power output if the amplifier’s safe operating temperature is exceeded. The amplifier will continue to operate and return

to normal power output once its temperature returns to a normal range.

8

JL AUDIO A2150

JL AUDIO A2150

9

Low-Voltageprotection:

If the car’s supply voltage drops below 10 volts, the entire amplifier will shut itself off to protect its internal circuitry. The green “Power” indicator will turn off when this occurs. The amplifier will turn back on when voltage climbs back above 10 volts. This may happen in a rapid cycle whenbass-heavyprogram material causes a weak charging system to dip below 10 volts momentarily. If this is happening in your system, turn your audio system off and have your power wiring, ground connections and charging system inspected.

SERVICING YOUR JL AUDIO AMPLIFIER

If your amplifier fails or malfunctions, please return it to your authorized JL Audio dealer so that it may be sent in to JL Audio for service. There are no user serviceable parts or fuses inside the amplifier. The unique nature of the circuitry in the JL Audio amplifiers requires specifically trained service personnel. Do not attempt

to service the amplifier yourself or through unauthorized repair facilities. This will not only void the warranty, but may result in the creation of more problems within the amplifier.

If you have any questions about the installation or setup of the amplifier not covered in this manual, please contact your dealer or technical support.

JL Audio Technical Support:

(954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

Monday - Friday

10

JL AUDIO A2150

JL AUDIO A2150

11

APPENDIX A:

Input Sensitivity Level Setting

Following the directions below will allow the installer to adjust the input sensitivity of each amplifier channel pair simply and easily in just a few minutes using equipment which is commonly available in installation bays.

Necessary Equipment

Digital AC Voltmeter

CD with a sine-wavetest tone recorded at 0 dB reference level in the frequency range to be amplified for that set of channels (50 Hz for subwoofer channels, 1 kHz for a

midrange application). Do not use attenuated test tones (-10dB,-20dB, etc.).

The Nine-StepProcedure

1)Disconnect the speaker(s) from the amplifier’s speaker output connectors.

2)Turn off all processing (bass/treble, loudness, EQ, etc.) on the source unit, processors (if used) and amplifier. Set fader control to center position and subwoofer level control to 3/4 of maximum (if used to feed the A2150).

3)Switch the “Input Voltage” switch to “Low” and turn the “Input Sens.” control all the way down.

4)Set the source unit volume to 3/4 of full volume. This will allow for reasonable gain overlap with moderate clipping at full volume.

5)Using the chart on this page, determine the target voltage for input sensitivity adjustment according to the nominal impedance of the speaker system connected to the amplifier outputs.

6)Verify that you have disconnected the speakers before proceeding. Play a track with an appropriate sine wave (within the frequency range to be amplified by the A2150) at 3/4 source unit volume.

7)Connect the AC voltmeter to the speaker output connectors of the amplifier. If the channel

pair is operating in stereo, it is only necessary to measure one channel. If bridged, make sure you test the voltage at the correct connectors (L+ and R–).

8)Increase the “Input Sens.” control until the target voltage is observed with the voltmeter.

9)Once you have adjusted the A2150 to its maximum low-distortionoutput level, reconnect the speaker(s). The “Input Sens.” controls can now be adjusted downward if the amplifier requires attenuation to achieve the desired system balance.

Do not increase any Input Sens.setting for any amplifier channel or channel pair in the system beyond the maximum level established during this procedure. Doing so will result in audible distortion and possible speaker damage.

It will be necessary to re-adjustthe “Input Sens.” for the affected channels if any equalizer boost is activated after setting the

Input Sens.” with this procedure. This applies to any EQ boost circuit, including source unit tone controls or EQ circuits. EQ cuts will not requirere-adjustment.

Nom.

Target AC Voltage

Impedance

Stereo

Bridged

 

 

 

 

13.4 V

26.8 V

13.4 V

25.6 V

13.4 V

24.6 V

12.8 V

not recommended

12.3 V

not recommended

 

 

 

APPENDIX B:

Precise Frequency Selection Chart

“FILTER FREQ” AMP FILTER

Detent

Panel

Actual

Number

Marking

Freq.

Full counter-clockwise:53

01 . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 02 . . . . . . . . . . . “50” . . . . . . . . . . . .53 03 . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 04 . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 05 . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 06 . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 07 . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 08 . . . . . . . . . . . “55” . . . . . . . . . . . .56 09 . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 14 . . . . . . . . . . . “60” . . . . . . . . . . . .65 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 20 . . . . . . . . . . . “80” . . . . . . . . . . . .81 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 26 . . . . . . . . . . “120” . . . . . . . . . . 115 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 28 . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 31 . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 32 . . . . . . . . . . “150” . . . . . . . . . . 177 33 . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 35 . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 36 . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 37 . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 38 . . . . . . . . . . “200” . . . . . . . . . . 218 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . 225

Full-clockwise:225

APPENDIX C:

A2150 Specifications

General Specifications:

Recommended Fuse Value: 20A

Recommended Fuse Type: AFS, AGU or MaxiFuse™

Input Sections:

No. of Inputs: One Stereo Pair

Input Type: Differential-balancedwith RCA jack inputs

Input Range: Switchable from 200mV - 2V RMS to 800mV - 8V RMS

Amplifier Section:

Amplifier Topology: Class A/B with patented Absolute Symmetry™ dual N-ChannelMOSFET output design

Power Supply: Unregulated MOSFET switching type

Rated Power at 12.5 V (Stereo, all channels driven):

45W RMS x 2 @ 4 ohms, 75W RMS x 4 @ 2 ohms Rated Power at 12.5 V (Bridged, all channels driven):

90W RMS x 1 @ 8 ohms, 150W RMS x 1 @ 4 ohms

THD at Rated Power:

<0.08% @ 4 ohms per ch. (20 Hz - 20 kHz)

Signal to Noise Ratio: >104 dB referred to rated power (A-weighted,20Hz-20kHz noise bandwidth)

Frequency Response: 10 Hz - 25 kHz (+0, -1dB)

Damping Factor: >200 @ 4 ohms per ch./50 Hz, >100 @ 2 ohms per ch. /50 Hz

Slew Rate: ± 22V/µs

Power output at 14.4V supply voltage and 1% THD: Rated Power (Stereo):

45W RMS x 2 @ 4 ohms (12.5V)

75W RMS x 2 @ 2 ohms (12.5V)

Rated Power (Bridged):

90W RMS x 1 @ 8 ohms (12.5V)

150W RMS x 1 @ 4 ohms (12.5V)

Amplifier Filter:

Filter Type: State-variable,12dB/octave Butterworth with continuously variable cutoff frequency selection from50-200Hz.

Configurable as Low-PassorHigh-Pass.Defeatable.

Preamp Output:

Pass-throughtype, buffered.

Dimensions(LxWxH):

9.8" x 9.25" x 2.50" (250mm x 235mm x 63.5mm)

Due to ongoing product development, all specifications are subject to change without notice.

12

JL AUDIO A2150

JL AUDIO A2150

13

APPENDIX D: TROUBLE SHOOTING

“How do I properly set the input sensitivity on my amplifier”

Please refer to Appendix A (page 12) to set the input sensitivity for maximum,low-distortionoutput.

“My amplifier doesn’t turn on”

Check the fuse, not just visually, but with a continuity meter. It is possible for a fuse to have poor internal connections that cannot be found by visual inspection. It is best to take the fuse out of the holder for testing. If no problem is found with the fuse, inspect thefuse-holder.

Check the integrity of the connections made to each of the “+12VDC”, “Ground”, and “Remote” terminals. Ensure that no wire insulation is pinched by the terminal set screw and that each connection is tight.

Check to make sure there is +12V at the“Remote” connection of the amplifier. In some cases, theturn-onlead from the source unit is insufficient to turn on multiple devices and the use of a relay is required. To test for this problem, jump the “+12VDC” wire to the “Remote” terminal to see if the amplifier turns on. If this does not work, proceed to the next step.

“I get a distorted / attenuated sound coming out of the speaker(s)”

Check the speaker wires for a possible short, either between the positive and negative leads or between either speaker lead and the vehicle’s chassis ground. If a short is present, you will experience distorted and/or attenuated output. The “Protect” light will illuminate in this situation. It may be helpful to disconnect the speaker wires from the amplifier and use a different set of wires connected to a test speaker.

Check the nominal load impedance to verify that each channel of the amplifier is driving a load equal to or greater than 2 ohms in stereo mode (4 ohms bridged).

Check the input signal and input signal cables to make sure signal is present at the“Amplifier Inputs” and the cables are not pinched or loose. It may be helpful to try a different set of cables and/or a different signal source to be sure.

“My amplifier’s output fluctuates when I tap on it or hit a bump”

Check the connections to the amplifier. Make sure that the insulation for all wires has been stripped back far enough to allow a good contact area inside the terminal block.

Check the input connectors to ensure that they all are making good contact with the input jacks on the amplifier.

“My amplifier shuts off once in a while, usually at higher volumes”

Check your voltage source and grounding point. The power supply of the A2150 will operate with charging system voltages down to 10V. Shutdown problems at higher volume levels can occur when the charging system voltage drops below 10V. These dips can be of very short duration making them extremely difficult to detect with a common DC voltmeter. To ensure proper voltage, inspect all wiring and termination points. It may also be necessary to upgrade the ground

wire connecting the battery to the vehicle’s chassis and the power wire connecting the alternator to the battery. Many vehicles employ small (10 AWG - 6 AWG) wire to ground the battery to the vehicle’s chassis and to connect the alternator to the battery. To prevent voltage drops, these wires should be upgraded to 4 AWG when installing amplifier systems with main fuse ratings above 60A. Grounding problems are the leading cause of misdiagnosed amplifier “failures.”

“My amplifier turns on, but there is no output”

Check the input signal using an AC voltmeter to measure the voltage from the source unit while an appropriate test tone is played through the source unit (disconnect the input cables from the amplifier prior to this test). The frequency used should be in the range that is to be amplified by the amplifier (example: 50 Hz for a sub bass application or 1 kHz for a full range /high-passapplication). A steady, sufficient voltage (between 0.2 and8.0-volts)should be present at the output of the signal cables.

Check the output of the amplifier. Using the procedure explained in the previous check item (after plugging the input cables back into the amplifier) test for output at the speaker outputs of the amplifier. Unless you enjoy test tones at high levels, it is a good idea to remove the speaker wires from the amplifier while doing this. Turn the volume up approximately half way. 5V or more should be measured at the speaker outputs. This output level can vary greatly between amplifiers but it should not be in the millivolt range with the source unit at half volume. If you are reading sufficient voltage, check your speaker connections as explained below.

Check to ensure that the speaker wires are making a good connection with the metal inside the terminal block. The speaker wire connectors are designed to accept up to 8 AWG wire. Make sure to strip the wire to allow for a sufficient connection with the metal inside the terminal block.

14

JL AUDIO A2150

JL AUDIO A2150

15

INSTALLATION NOTES:

Use this diagram to document your amplifier’s switch and control positions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

 

JL AUDIO A2150

 

 

 

JL AUDIO A2150

17

INSTALLATION NOTES:

INSTALLATION NOTES:

18

JL AUDIO A2150

JL AUDIO A2150

19