Intermatic T106R User Manual

Size:
27.73 Kb
Download

158TS10916 10/31/03 10:06 AM Page 1

MODEL: T106R

LR3730

 

24 HOUR DIAL TIME SWITCH

IN TYPE 3R RAINPROOF ENCLOSURE SUITABLE FOR POOL

EQUIPMENT CONTROL IF INSTALLED 5 FT. OR MORE FROM EDGE OF POOL

ONE NORMALLY OPEN - ONE NORMALLY CLOSED CONTACTS

MAY BE WIRED AS SINGLE POLE DOUBLE THROW.

40 AMP. RESISTIVE INDUCTIVE, TUNGSTEN OR

1000 VA PILOT DUTY 120-277VOLT AC;

2 HP (24 FLA)-120VAC; 5 HP (28FLA)-240VAC.

CLOCK MOTOR: 208-277VOLTS - 60 HZ.

CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO ORDER REPLACEMENT, INDICATE ART NO. (WG--)ON MOTOR COVER.

CLOCK

ON

 

 

 

CLOCK

 

WIRING DIAGRAM

 

 

 

 

 

 

DIAL

TRIPPER

 

 

 

MOTOR

 

 

 

FROM GRD

 

 

 

 

 

 

 

A

 

 

 

 

TIME

 

208V,

 

1

2

3

4

POINTER

 

240V

 

 

 

 

OR

 

 

 

 

 

 

OFF

 

277V

LINE

 

 

 

 

TO

TRIPPER

 

SUPPLY

 

 

 

 

 

 

 

 

 

 

LOAD

MANUAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GROUND

LEVER

 

TYPICAL WIRING SINGLE POLE NORMALLY OPEN

 

 

 

SEE WIRING INSTRUCTIONS BELOW FOR OTHER TYPES

WIRING INSTRUCTIONS: To wire switch follow diagram above. To wire asSINGLE POLE NORMALLY CLOSED, move motor lead from terminal 3 to 1, and connectLINE to 1,LOAD to 2. To wire asSINGLE POLE DOUBLE THROW, install jumper (the same gauge asLINE wire) between terminals 2 and 3 and connectLINE to 2,LOADS to 1 and 4. NOTE: Line 2 if present is uninterrupted. Use COPPER wire only. For gauge selection and wire connection, see details below. Use 3/16 or larger screwdriver to tighten terminal screws firmly. (25lb-inminimum).

REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.

MINIMUM

MAX.

MIN.

 

75°C INSULATION MAX. MOTOR

COPPER

LOAD

INSUL-

 

 

LOAD (HP)

 

WIRE SIZE

(AMP)

ATION

SINGLE PHASE

3 PHASE

(AWG)

 

TEMP(°C)

 

 

 

120 V.

 

240 V.

208 V.

240 V.

14

15

60

1/2

 

2

 

 

12

20

60

1

 

2 1/2

N/A

N/A

10

30

60

2

 

3

 

 

 

8

40

75

-

 

5

 

 

 

 

 

 

 

 

 

 

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE INSULATION CLEARS PRESSURE PLATE

PROGRAMMING INSTRUCTIONS

1.TO SET “ON” AND “OFF” TIMES: Hold trippers against edge of CLOCK-DIAL, pointing to time (AM or PM) when ONand OFFoperations are desired, tighten tripper screws firmly. For additional tripper pairs on CLOCK-DIALorder 156T1978A.

2.TO SET TIME-OF-DAY:Pull CLOCK-DIALoutward. Turn in either direction and align the exact time-of-day on the CLOCKDIAL(the time now, when switch is being put into operation) to the pointer. DO NOT MOVE POINTER.

OPERATING INSTRUCTIONS

TO OPERATE SWITCH MANUALLY: Move MANUAL LEVERbelow CLOCK-DIALleft or right as indicated by arrows. This will not effect next operation.

IN CASE OF POWER FAILURE, reset CLOCK-DIALto proper time-of-day. See programming instructions.

INTERMATIC INCORPORATED

158TS10916 SPRING GROVE, ILLINOIS60081-9698