Intermatic DD175MV User Manual

Size:
98.54 Kb
Download

HID Dusk-To-Dawn- DD Series

INSTALLATION INSTRUCTIONS

Lamp Types: Mercury Vapor 175 Watt

Models: DD175MV

FOR OUTDOOR USE ONLY

NOT FOR USE IN HAZARDOUS ATMOSPHERES IMPORTANT: Read instruction sheet carefully before installing fixture.

Retain instructions for future reference.

ELECTRICAL REQUIREMENTS

A qualified electrician should complete all required wiring. This fixture will accept 120 volt AC and must be properly grounded for safety. A mounting suitable for outdoor use and rated for wet locations is required. Follow all applicable electrical codes and regulations.

WARNING: Electric shock hazard

Disconnect power at circuit breaker or fuse box before installing or servicing light.

WARNING: Fire hazard

USE MIN 75ºC SUPPLY CONDUCTORS.

CONNECT TO SUPPLY IN EXTERNAL JUNCTION BOX ONLY.

Lamp and housing become very hot during use.

Ensure free air circulation around unit to dissipate heat.

Avoid enclosed locations and locations where flammable debris (leaves, cut grass, etc.) might collect. Avoid locations where humans or animals might accidentally touch fixture.

WARNING: Explosion hazard

Never operate light without securing the lens door. When light is operating, the gas in the lamp inner arc tube is at high pressure.

Never operate light if the fixture lens or outer glass envelope of the lamp is broken or missing.

WARNING: Explosion hazard

Wear safety glasses and gloves when handling lamp, Mercury Vapor outer envelope is pressurized and could explode if broken.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: UV hazard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The type of lamp used in this fixture can cause serious skin burn and eye inflammation from short wave ultra

 

violet radiation if outer envelope of the lamp is broken or punctured, and the arc tube continues to operate. Do

 

not use where people will remain for more than a few minutes. Certain types of lamps that will automatically

 

extinguish when the outer envelope is broken or punctured are commercially available.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOUNTING & WIRING

 

 

 

 

Photocontrol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Receptacle/socket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Attach the two-piecemounting bracket to the

 

 

 

 

 

 

 

 

 

 

 

 

Photocontrol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

extension arm by interlocking the halves and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

securing with the bolt and hex nut provided.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Leave approximately one inch of the

 

 

 

 

 

Fixture

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

extension arm protruding from the bottom of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the bracket. (See Figure 1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Extension arm

 

 

 

 

 

 

 

 

Bulb Socket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Place the mounting bracket and arm

 

 

 

Reflector

 

 

 

 

Mounting

Clamp

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bracket

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

assembly on the desired mounting surface.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lag Bolts (4)

 

Mark the four hole locations required for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connection Plug

 

 

 

 

 

mounting. Put the assembly aside and

 

 

 

 

 

Lens

 

 

 

 

 

 

 

 

(Not Provided)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Conduit Connector

 

 

 

 

prepare the marked locations for attaching

 

 

 

 

 

 

 

 

 

 

 

 

 

(Not Provided)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the mounting bracket and arm assembly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Conduit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Not Provided)

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 1

 

 

 

 

 

Mounting screws

 

 

 

 

 

 

for reflector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.Mount the extension arm assembly using the hex head lag bolts provided or other suitable method. Secure the mounting bracket solidly to the mounting surface.

4.Feed supply wires through the arm and connect them to the fixture. (See Figure 2)

a.Connect the Black fixture wire to the Black (hot) supply wire.

b.Connect the White fixture wire to the White (neutral) supply wire.

c.Connect the supply grounding wire to the green screw located on the one-piecefixture mounting arm clamping bracket.

 

 

 

 

LAMP

 

120 V

 

 

 

 

COM

 

COM

 

 

 

 

 

 

 

Figure 2

 

 

5.

Secure the fixture to the arm using the one-piececlamping bracket and bolts provided.

6.

Fasten the reflector and lens assembly to the fixture using the two screws and washers provided.

7.

Screw lamp into socket in lamp holder until finger tight.

 

 

8.

Insert the photocontrol into the socket on top of the fixture by aligning the prongs and twist clockwise to lock.

9.

The arrow on top of control should be pointed away from the mounting surface.

 

a. If it is not, remove the photocontrol and reposition the socket on the top of the fixture by loosening the

 

screw in the center of the socket. Do not remove the screw.

 

 

b. Rotate socket to new position and retighten screw. Do not rotate over 360 degrees.

10.

Turn on the electric power to the fixture.

 

 

 

 

When power if first applied, some controls will turn the light on and turn off in two or three minutes. The

 

fixture will take approximately 5-7minutes to achieve full illumination.

11.

To check operation during daylight, cover the photocontrol with black electrical tape. Allow 3-5minutes for the

 

fixture to turn off or on when testing. Be sure to remove the tape when testing is completed.

CAUTION: Do not use lamp beyond manufactures rated life to reduce chance of lamp rupture.

Turn lamp off at least once for 15 minutes per week to reduce chance of lamp rupture.

LAMP REPLACEMENT

CAUTION: Use lamp of correct type and wattage as specified on fixture.

1.Turn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.

2.Remove old lamp and replace with new lamp of correct type and wattage. Screw lamp into socket in lamp holder until finger-tight.

3.Turn power back on. If desired, test operation as described in steps 10 and 11 above.

4.Properly dispose of lamp per manufacturer’s recommendations.

LIMITED 1 YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.

THESE INSTRUCTIONS DO NOT COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS RELATED

TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR DISTRIBUTOR OR

INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000www.intermatic.com

158HL12129