User Guide | Guide de l’utilisateur | Guía del Usuario
Amplifier and Subwoofer | Amplificateur et caisson d'extrêmes graves | Amplificador y Subwoofer
NS-P2000
Congratulations on your purchase of a high-quality Insignia product. Your NS-P2000 represents the state of the art in car power amplifier and 12-inch sub-woofer design, and is designed for reliable and trouble-free performance.
Cutout for speaker = 11.02 inches in diameter
www.insignia-products.com |
3 |
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting up your amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Using your amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1 Year Limited warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warning
Caution
Exercise extreme caution when you operate the amplifier near an open gasoline tank or electrical wires. Failure to comply with this warning could result in injury or death.
Speaker damage can result from high volume levels.
Protect connecting wires and parts to avoid damage or short circuits.
To protect the amplifier unit, make sure the power connection from the positive (+) battery terminal to the amplifier is correctly fused.
The sound system must be turned off before checking the amplifier.
When you replace an amplifier fuse, make sure you use the same fuse type and capacity (30A).
4 |
www.insignia-products.com |
Connect to remote turn-on lead of source unit.
Connect to |
|
|
chassis ground |
Speaker impedence 4 to 8 Ohm |
|
of vehicle |
||
|
www.insignia-products.com |
5 |
Connect to remote turn-on lead of source unit.
Connect to |
|
chassis ground |
|
of vehicle |
Speaker impedence 4 to 8 Ohm |
|
6 |
www.insignia-products.com |
A B C D E
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
F |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
G |
H |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Item |
Name |
Function or Control |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A |
HIGH - |
Left and right high level inputs to the amplifier. |
|||||||||||||||||
|
INPUT |
Connect high level inputs here. |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
B |
LOW - |
Left and right channel inputs to the amplifier |
|||||||||||||||||
|
INPUT |
system. Connect preamplifier outputs from a |
|||||||||||||||||
|
|
|
|
|
|
|
source (such as a head unit, CD player, or DAT) or |
||||||||||||
|
|
|
|
|
|
|
from an external electronic crossover here. |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C |
GAIN |
Set for volume range adjustment. |
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D |
HPF |
Set for High Pass Filter frequency (45 Hz to |
|||||||||||||||||
|
|
|
|
|
|
|
300 Hz). |
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
E |
BASS |
Set for amount of bass boost required (0dB, +6dB, |
|||||||||||||||||
|
BOOST |
or +12dB). |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
F |
Indicator |
Green LED lit—Amplifier is on and functioning |
|||||||||||||||||
|
LED |
correctly. |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
Red LED lit—Amplifier is in self-protect mode. |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
G |
X-OVER |
Switch for setting high pass filter (HPF), full pass |
|||||||||||||||||
|
|
|
|
|
|
|
filter (FULL), or Low Pass Filter (LPF). |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
H |
LPF |
Set for Low Pass Filter frequency (45 Hz to |
|||||||||||||||||
|
|
|
|
|
|
|
300 Hz). |
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
www.insignia-products.com |
7 |
A B C
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Item |
Name |
Function or Control |
||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A |
POWER/ |
|
• +12 Volts - Connect to positive (+) battery |
|||||||||||||||||||
|
BATTERY |
|
|
terminal. |
||||||||||||||||||
|
|
|
|
|
|
|
|
|
• REM - Connect to the Remote cable from the |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
signal source to control amplifier switching. |
||||||||||||
|
|
|
|
|
|
|
|
|
|
Applied voltage must be between 7 and |
||||||||||||
|
|
|
|
|
|
|
|
|
|
15VDC. |
||||||||||||
|
|
|
|
|
|
|
|
|
• GND - Connect to good ground, such as the |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
car frame or grounded metal body. Keep |
||||||||||||
|
|
|
|
|
|
|
|
|
|
ground cable length as short as possible. |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
B |
FUSE |
Amplifier protection fuse. Replace with the same |
||||||||||||||||||||
|
|
|
|
|
|
|
|
type and capacity. |
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C |
SPEAKER/ |
Connect the speakers to these terminals. |
||||||||||||||||||||
|
BRIDGED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RMS power @13.8VDC |
|
|
Power @ 4 Ohms............................... |
200W × 2 |
|
Power @ 2 Ohms............................... |
300W × 2 |
|
Bridged power @ 4 Ohms ................. |
500W × 1 |
|
Minimum speaker impedance.............. |
2 Ohms |
|
THD distortion ....................................... |
0.08% |
|
IMD distortion........................................ |
0.08% |
|
Frequency response............................. |
20 Hz to 20 KHz |
|
Input sensitivity..................................... |
200mV to 6V |
|
Input impedance ................................... |
15K Ohms |
|
Signal-to-noise ratio ............................. |
90dB |
8 |
www.insignia-products.com |
|
|
|
|
|
|
...............................Channel separation |
50dB |
||||
Crossover network |
|
|
|
|
|
Low pass filter.................................... |
45 Hz to 300 Hz |
||||
Bass boost ......................................... |
0dB to +12dB |
||||
High pass filter ................................... |
45 Hz to 300 Hz |
||||
Fuse rating............................................. |
30A × 2 |
||||
Size L × W × H ....................................... |
18.43 × 10.16 × 2.56 inches |
||||
|
(468 × 258 × 65 mm) |
Woofer size ................................................ |
12 inch diameter |
Woofer material ......................................... |
Plating injection-molded |
|
cone with polypropylene |
|
material |
Magnet size................................................ |
82 oz. |
Continuous power handling..................... |
200 W |
Peak power handling ................................ |
400 W |
Impedance ................................................. |
8 Ohms |
Sensitivity .................................................. |
88.7dB |
Voice coil.................................................... |
2-inch Black anodized |
|
aluminum ESV wire |
Free air resonance frequency Fs............. |
36 Hz |
Frequency response................................. |
36 Hz-2 KHz |
Total Q factor (Qts).................................... |
0.53 |
Connection type........................................ |
Screw terminals |
Number of voice coils............................... |
One |
Frame material .......................................... |
Stamped steel |
Surround material ..................................... |
Rubber |
Dimensions: |
|
Mounting depth ...................................... |
6.02 inches (153 mm) |
Total depth ............................................. |
6.69 inches (170 mm) |
Overall diameter..................................... |
12.4 inches (315 mm) |
Mounting hole diameter (cutout) ............ |
11.02 inches (280 mm) |
Weight ........................................................ |
12.10 lb. (5.5 kg) |
Recommended enclosure size ................ |
48.6 L |
Other features: |
|
•Insulated 24-gauge tinsel leads
•Linear spider improves mechanical stability under high excursion and eliminates the need for a subwoofer break-in period.
www.insignia-products.com |
9 |
Before removing your amplifier, locate the problem in the following table. Always test the speakers and speaker wires before troubleshooting the amplifier.
Symptom |
Solution |
|
|
The amplifier |
• Make sure that the amplifier has a good |
will not turn on. |
ground connection. |
|
• Make sure that the power at the remote |
|
DC terminal is at least 7VDC. |
|
• Make sure that there is battery power at |
|
the positive (+) terminal. |
|
• Make sure that all fuses are good. |
|
• Make sure that the indicator LED is not |
|
red. If the indicator LED is red, turn off |
|
the amplifier briefly, then turn it back on. |
|
|
A high hiss or |
Disconnect all RCA inputs to the amplifier. If |
engine noise |
the hiss or noise goes away, plug in the |
(alternator |
component driving the amplifier and unplug its |
whine) is |
inputs. If the noise goes away, start plugging |
audible in the |
in the inputs until the noisy component is |
speakers. |
found. |
|
We recommend that you set the amplifier |
|
input sensitivity as low as possible. This will |
|
result in the best possible S/N ratio. Also, try |
|
to drive as high a signal level as possible from |
|
the head unit. |
|
|
The indicator |
• Make sure that there are no shorts on |
LED turns red |
the speaker leads. |
when the |
• Make sure that the volume control on the |
amplifier is |
head unit is turn down low. |
turned on. |
• Remove the speaker leads and reset the |
|
amplifier. If the indicator LED is still red, |
|
the amplifier is faulty. |
|
Note: To protect the amplifier from damage, it |
|
will shut down automatically when its |
|
temperature reaches 176°F (80°C). |
|
|
The amplifier |
• Make sure that the minimum speaker |
gets very hot. |
impedance is correct. |
|
• Make sure that there are no speaker |
|
shorts. |
|
• Make sure that there is good airflow |
|
around the amplifier. In some situations, |
|
a fan may be required for proper cooling |
|
of the unit. |
|
|
10 |
www.insignia-products.com |
|
|
|
|
|
|
|
|
|
|
|
|
|
Symptom |
Solution |
|
||
|
|
|
|
|
|
|
The sound is |
• Make sure that the level control(s) is set |
|
||
|
distorted. |
to match the signal level of the head unit. |
|
||
|
|
• Make sure that the crossover |
|
||
|
|
frequencies have been correctly set. |
|
||
|
|
• Make sure that there are no shorts on |
|
||
|
|
the speaker leads. |
|
||
|
|
|
|
|
|
|
There is a high |
Make sure that the RCA patch cords are |
|
||
|
squeal noise |
correctly grounded. |
|
||
|
coming from |
|
|
|
|
|
the speakers. |
|
|
|
|
|
|
|
|
|
|
|
Sub-woofers |
Always test the speakers and speaker wires. |
|
||
|
are not |
Make sure the speakers are connected with |
|
||
|
working. |
the correct polarity (positive (+) amplifier |
|
||
|
|
output to positive (+) speaker terminal, |
|
||
|
|
negative (-) amplifier output to negative (-) |
|
||
|
|
speaker terminal). |
|
||
|
|
|
|
|
|
www.insignia-products.com |
11 |
1 Year Limited warranty
Insignia Products (“Insignia”) warrants to you, the original purchaser of this new NS-P2000 (“Product”), that the Product shall be free of defects in the original manufacture of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”). This Product must be purchased from an authorized dealer of Insignia brand products and packaged with this warranty statement. This warranty does not cover refurbished Product. If you notify Insignia during the Warranty Period of a defect covered by this warranty that requires service, terms of this warranty apply.
The Warranty Period lasts for 1 year (365 days) from the date you purchased the Product. The purchase date is printed on the receipt you received with the Product.
During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized Insignia repair center or store personnel, Insignia will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty lasts as long as you own your Insignia Product during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product.
If you purchased the Product at a retail store location, take your original receipt and the Product to the store you purchased it from. Make sure that you place the Product in its original packaging or packaging that provides the same amount of protection as the original packaging. If you purchased the Product from an online web site, mail your original receipt and the Product to the address listed on the web site. Make sure that you put the Product in its original packaging or packaging that provides the same amount of protection as the original packaging.To obtain in-home warranty service for a television with a screen 25-inch or larger, call 1-888-BESTBUY. Call agents will diagnose and correct the issue over the phone or will have an Insignia-approved repair person dispatched to your home.
12 |
www.insignia-products.com |