InFocus IN5502, IN5534, IN5532, IN5504 User Manual

Guide User’s IN5534 IN5532, IN5504, IN5502,

5500

Regulatory models: F5500, F5530

010-0715-02

Declaration of Conformity

Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland,

Oregon 97223-8368 USA

We declare under our sole responsibility that this projector conforms to the following directives and norms:

EMC Directive 2004/108/EC EuP Directive 2005/32/EC EMC: EN 55022

EN 55024 EN 61000-3-2 EN 61000-3-3

Low Voltage Directive 2006/95/EC Safety: IEC 60950-1:2005, MOD

Trademarks

DisplayLink is a trademark of DisplayLink Corporation.

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

EN 55022 Warning

This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, cUL

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory models F5500, F5530. Input ratings:

For Single Lamp models (F5500) - AC100-240V 5.0-2.0A, 50-60Hz For Dual Lamp models (F5530) - AC 100-240V, 9.5-3.5A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

1

Table of Contents	Index	64
Introduction	5
Positioning the projector	7
Ceiling Mount	8
Cable management	8
Connecting power	9
Connecting a computer source	9
Optional computer connections	10
Displaying an image	11
Adjusting the image	12
Connecting a video device	13
Video device connections	13
Shutting down the projector	15
Troubleshooting your setup	15
Using the remote control	23
Using the audio	24
Using the keypad buttons	25
Optimizing computer images	25
Presentation features	25
Optimizing video images	26
Customizing the projector	26
Dynamic Messaging	26
Using the menus	27
Basic Picture menu	28
Advanced Picture menu	29
Setup menu	30
Status and Service menu	33
Help	33
Using Network Functions	34
Using LitePort	38
Maintenance	41
Cleaning the lens	42
Replacing the projection lamp (single lamp)	43
Replacing the projection lamp (dual lamp)	44
Using the security lock	47
Appendix	48
Projected Image Size	48
Optional Lenses	49
SplitScreen Compatibility	53
RS-232 commands	45

2

Important Operating Considerations for Safety

•Refer to this guide for proper startup and shutdown procedures.

•Follow all warnings and cautions in this manual and on the projector.

•Do not block the lens with any object while the projector is being used. Blocking the light path can cause overheating and result in fire.

•Place the projector in a horizontal position no greater than 8 degrees off axis.

•Locate the projector at least 4' (1.2m) away from any heating or cooling vents.

•Do not block ventilation openings. Locate the projector in a wellventilated area without obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.

•Do not place the projector in direct sunlight, humid, greasy or dusty places or in places where the projector may come into contact with smoke or steam.

•Do not look directly into the lens while the projector is being used.

•Do not drop the projector.

•Do not spill liquid on the projector. Spilled liquid may damage the projector.

•Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal. A surge-protected power strip is recommended.

•Do not overload wall outlets.

•When disconnecting the power cord, hold the plug, not the cord.

•Wash hands after handling the cables supplied with this product.

•The projector remote control uses batteries. Make sure the batteries’ polarity (+/-) is aligned correctly. Dispose of used batteries in accordance with local disposal laws.

•Use an InFocus approved ceiling mount kit for proper fitting, ventilation and installation. The warranty does not cover any damage

caused by use of non-approved ceiling mount kits or by installing in an improper location.

•When the projector is ceiling mounted, wear protective eyewear to prevent eye injury before opening lamp door.

•The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself.

•Refer all service to qualified service personnel. Servicing your own projector can be dangerous to you and will void the warranty.

•Only use replacement parts specified by InFocus. Unauthorized substitutions may result in fire, electrical shock, or injury, and may void the warranty

•Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty.

•Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

•The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.

•In the unlikely event of a lamp rupture, particles may exit through the projector vents. Keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below..

3’/1m

8							m
							.
	’ /	2					5
			.4			1
				m	/
					’
					5

3

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.

IMPORTANT: Unpacking/Transport Notes for the IN5502, IN5504, IN5532 and IN5534

When unpacking your projector, remove the black Lens Protector Ring from around the lens in order to allow full movement of the lens.

KEEP the Lens Protector Ring for future transport purposes. The Lens Protector ring should be re-installed before transporting the projector to prevent damage to the lens shift mechanism.

When preparing the projector for transport, the lens needs to be centered before the Lens Protector Ring can be installed. To do this, access the Lens Shift>Auto Center feature in the Basic Picture menu.

IMPORTANT: Unpacking/Shipping Notes for the IN5502L, IN5504L, IN5532L and IN5534L

When unpacking your projector, remove the clear Optical Engine Cover from the lens area in order to install the optional lens.

KEEP the clear Optical Engine Cover for future shipping purposes. The optional lens should be removed and the Optical Engine Cover replaced when the projector is being shipped for repair and/or other purposes.

Whenever the optional lens is removed, replace the clear Optical Engine Cover in order to minimize contamination from within the engine compartment.

4

Introduction

Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing, too. The IN5502 and IN5532 have WXGA 1280x800 resolution and the IN5504 and IN5534 have native WUXGA 1920x1200 resolution. This guide applies to all four products. They are compatible with a wide variety of computers and video devices.

Product Specifications

To read the latest specifications on your multimedia projector, be sure to visit our support website at www.infocus.com/support, as specifications are subject to change.

Online Registration

Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.

Included Items

	Projector
Remote Control	VGA Computer cable
	Documentation
Power Cord	USB cable

Optional Accessories

Optional accessories include optional top covers in a variety of finishes, optional lenses, the Commander-2 remote, ceiling mount, DisplayLink Extender, DisplayLink Wireless Adapter, and LiteShow II. These items and other accessories can be found on our website at www.infocus.com or at your local dealer.

		Top rear cover			LiteTouch keypad and
Top front cover					Remote control receiver

			Remote control
Lens
			receiver (IR)

Power cord connector

Connector panel

5

Connector Panel

The projector provides both computer and video connection options, including:

•VGA computer (2)

•HDMI (2)

•S-video

•Composite video

•Component video

•BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV

•Separate audio inputs for video and computer

•USB DisplayLink connector, for computer audio/video input. This USB connection also provides power out for the Wireless DisplayLink Projector Adapter.

The projector also provides the following connectors:

•Monitor out, to provide an image on your desktop computer as well as on the projection screen.

•LAN port for network control and web server.

•LitePort, for connecting a USB flash drive containing JPEG images.

•Audio out, to provide sound for external speakers.

•5 volt DC output

•12V screen trigger output

•Wired remote jack

•RS-232 connector for serial control. Command control codes are in the Appendix and on our support website at www.infocus.com/support.

NOTE: Only VGA video is sent to the Monitor out connector.

5 volt DC output

The coaxial 6.4mm x 2.2mm jack provides a constant 5 volt, 2 amp DC output when the projector is on, and will also provide power when the projector is in standby (powered off) if Network and DisplayLink items in the Always-On Functions submenu are set to Yes. It is designed to provide

power to an InFocus LiteShow II wireless device or InFocus DisplayLink Extender device.

12V Screen Trigger output

The 3.5mm mini-jack screen trigger provides a 12 volt, 0.25 amp DC output. It turns on when the lamp is lighted. If you connect your projection screen to this output using the cable that came with your screen, the screen will move down when the lamp is turned on and the screen will return to its storage position, when the lamp is turned off.

5V DC Output	12V Screen Trigger		Monitor out
RS-232	Output		Wired	Security lock
	HDMI	VGA	remote
RGBHV
YPbPr
Audio in
Audio out
Composite
video

S-video Component	DisplayLink Liteport LAN
video	connector

Cable cover

6

Positioning the Projector

To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:

•Position the projector on a flat surface at a right angle to the screen. The projector (with the standard lens) must be at least 3 feet (0.9m) from the projection screen.

•Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object.

•Position the projector to the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.

•For the standard lens that comes with the projector, the image exits at a given angle. However, the lens shift feature makes the image offset variable.

•The vertical image offset range for all the projectors is 50% - 110% (default 80%), and the horizontal image offset is +/-10% (default 0%). At 110% offset, 10% of the image height resides above the lens center in tabletop configuration. At 50% offset, 50% of the image height resides above the lens center in tabletop configuration.

Vertical Image Offset is 50 - 110%

110% offset

lens center

50% offset

Horizontal Image Offset is +/-10%

7

Ceiling Mount

If you wish to install the projector on the ceiling:

•The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself.

•We strongly recommend using InFocus approved ceiling mounts for proper fitting, ventilation and installation. Refer to the installation guide that comes with the InFocus Ceiling Mount Kit (p/n SP-CEIL- INSTALL) for more information. The warranty does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper location.

•The ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. Consult your dealer for more information.

•Maximum supported physical pitch is +/-8º.

•Maximum supported physical horizontal roll is +/-8º.

•Keep all adjacent surfaces 3” (76mm) from sides, front and rear and

.87” (22mm) from the bottom of projector to preserve required airflow around the projector.

8º

DisplayLink

Cable Management

The integrated cable management system allows you to keep the cables organized. To use the cable management system, thread the cables into the slots as shown in the illustration.

cable management system

Using the cable management system provides you with a clean, professional-looking installation.

8

Connecting power

Connect the black power cord to the Power connector on the rear of the projector and to your electrical outlet. The Power light on the Status Indicator Panel (page 15) turns amber.

NOTE: Always use the power cord that shipped with the projector.

Connecting a computer source

DisplayLink

If you have a Windows or Macintosh computer, connect the USB cable between your computer's USB port and the projector's DisplayLink connector*. Then to begin installation of the DisplayLink software:

Windows: Follow the instructions on the screen.

Macintosh: A folder will open containing a file named DisplayLink Installer.pkg. Open that file and follow the instructions on the screen.

* For detailed DisplayLink instructions and troubleshooting, and to download the latest DisplayLink software, go to www.infocus.com/support/displaylink.

VGA connection

Connect one end of the provided computer cable to the VGA 1 or VGA 2 connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first (you can connect this monitor cable to the Monitor Out connector on the projector, see next page).

HDMI 1.3 connection

HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video out connector on the video device and into either the HDMI 1 or HDMI 2 connector on the projector.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3- compatible source.

RGBHV connection

Connect one end of the BNC cable to the computer and the other end of the cable into the BNC connectors on the projector.

Connect power cord

Connect USB cable

Connect computer cable

9

Optional computer connections

To get sound from the projector, connect an audio cable (optional cable, sold separately) to your computer and to the Audio 1 (used with VGA 1) or Audio 2 (used with VGA 2) connector on the projector. You can also assign your source to a different audio in connector, see page 24 and page 31. You may also need an adapter.

If you are using a desktop computer and want to see the image on your computer screen as well as on the projection screen, connect the computer’s monitor cable to the Monitor Out connector on the projector.

NOTE: Only VGA video is sent to the Monitor out connector.

To display a presentation using a USB flash drive, see the Using LitePort section on page 38. This feature converts presentations to JPEG images and eliminates the need for a computer source. It can also be integrated with common wall plates and conference room input/output panels.

To advance slides in a PowerPoint presentation using the remote control, plug the USB cable between the projector’s DisplayLink connector and your computer. Then press the up and down arrow buttons on the remote control to move through your slides.

Connect monitor cable

Connect audio cable

10

Displaying an image

Touch the Power button on the keypad or the remote.

The Power button blinks green, a beep will sound and the fans start to run. When the lamp turns on, the start up screen will display and the Power button will become solid green. It can take a minute for the image to achieve full brightness.

No start up screen? Get help on page 16.

Turn on your computer or video device.

The image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad or remote.

If you are using a VGA cable to connect your computer to the projector (instead of DisplayLink):

If using a laptop, make sure its external video port is active.

Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like Fn + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press Fn and the labeled function key simultaneously.

Refer to your laptop’s documentation for more information about your laptop’s key combination or go to the InFocus website at:

http://www.infocus.com/Support/LaptopActivation.aspx.

No laptop image? Try pressing the Auto Image button on the keypad or remote. Get help on page 25.

Is your laptop connected to the projector's DisplayLink connector? See the InFocus DisplayLink Software User's Guide (available on the InFocus website at www.infocus.com/displaylink) for troubleshooting information.

Press Power button

Turn on computer or video device

Activate laptop’s external port

Monitor key or

LCD/CRT key

Fn key

11

Adjusting the image

Position the projector to the desired distance from the screen at a 90 degree angle to the screen. See the Appendix for screen sizes and distances associated with the various lens options.

If the image is square but not centered on the screen or viewing area, adjust Zoom or Focus in the Basic Picture menu. (You can also hold down the Select button for 10 seconds to turn the focus control on.) Then adjust Digital Horz Shift and Digital Vert Shift until the image is centered. See page 28 for help with these menu adjustments.

Rotate the elevator feet for granular adjustment of the projector’s height. Avoid placing your hands near the hot exhaust vent at the back of the projector.

Adjust the Contrast or Brightness in the Basic Picture menu. See page 28 for help with these menu adjustments.

Adjust distance

Adjust zoom, focus and lens shift.

Adjust height

Release button Elevator foot

12

Connecting a video device

You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the audio directly to the projector to get sound from the built-in speakers, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.

You can connect the projector to most video devices that can output video. You cannot directly connect the coaxial cable that enters your house from a cable or satellite company; the signal must pass through a tuner first.

Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.

Although the aspect ratio is automatically selected by the projector based on the signal input, you can change the aspect ratio, if desired. The projector’s Aspect Ratio setting is accessed through the Resize button on the remote or through the projector’s Basic Picture Menu. See page 28 for more information.

Video device connections

No video cables are provided with the projector. You can order cables from InFocus or use your own.

Composite video connection

Plug the composite video cable’s yellow connector into the video out connector on the video device. Plug the other yellow connector into the yellow Composite connector on the projector.

Plug the white connector of a Mini-plug audio Y-cable into the left audio out connector on the video device and plug the red connector into the right audio out connector on the video device. Plug the other end of the cable into the associated audio in connector on the projector.

Keep in mind that video output from composite connections is not as high quality as S-video.

HDMI 1.3 connection

HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video out connector on the video device and into either the HDMI 1 or HDMI 2 connector on the projector.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3- compatible source.

S-video connection

If your video device uses a round, four-prong S-video connector, plug an S- video cable into the S-video connector on your video device and into the S- video connector on the projector. Use the audio cable as described above.

Keep in mind that S-video delivers higher quality video output than composite.

VGA connection

If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the VGA 1 or VGA 2 connector on the projector.

Component video connection

Plug the component cable into the video device. Plug the other end of the component cable into the Component connectors (or if using BNC connectors, plug into the RGBHV or YPbPr connectors as appropriate).

In addition, a Component to VGA adapter can be used in conjunction with the VGA connectors. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the VGA 1 or VGA 2 connector.

Component offers the highest quality analog video output.

13

What is Aspect Ratio?	4:3 screen			16:9 screen
Aspect ratio is the ratio of the image width to image height. Standard TV
screens and older laptops are 4:3; HDTV and most DVDs are 16:9; and
widescreen computers are 16:10. If you are projecting onto a screen, the
size/shape of the screen will influence the aspect ratio you decide to use. If
you are projecting onto a blank wall, there are no screen size restrictions.							4:3
What you plan to project will also help you choose between 4:3, 16:9 or							mode
16:10. Many TV shows are 4:3, while most movies are 16:9.
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
widescreen movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for widescreen movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Force Wide can also be enabled to
automatically resize less common aspect ratios to 16:10.
							16:9
							mode

Native mode

14

Shutting down the projector

Screen Save Time

You can make the black screen appear after a preset number of minutes by turning on the Screen Save Time feature in the Setup menu. See page 30.

Auto Off Time

The projector has an Auto Off Time feature that automatically turns the projector off if no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off. You can change the length of time, see page 30.

Turning off the projector

To turn the projector off, press the Power button on the remote or keypad. The lamp turns off, a beep sounds and the LED blinks amber for 10 seconds while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely power off the projector.

Troubleshooting your setup

The Status Indicator Panel on top of the projector indicates the state of the projector and is helpful when troubleshooting.

Table 1: Status indicator light behavior and meaning

Icon	Meaning
Power, solid amber	The projector is plugged in.
Power, blinking green	The power button has been pressed and the software is
	initializing.
Power, solid green	The projector is on and initialized.
Power, blinking amber	The power button has been pressed to turn the projector
	off and the fans are running to cool the projector.
Temperature	The projector is too hot. Make sure the vents aren’t blocked
	(see page 21). Turn the projector off and wait one minute,
	then turn the projector on again. Contact Technical Support
	if the problem persists. Visit www.infocus.com/support to
	contact service.
Lamp	Turn the projector off and wait one minute, then turn the
	projector on again. If the lamp light turns on again, replace
	the lamp and reset the lamp timer (page 43).
	Note: For dual-lamp projectors, one blink off every 2
	seconds means the problem is with lamp #1; two blinks off
	every 2 seconds means the problem is with lamp #2.
Wrench/Service	Turn the projector off and wait one minute, then turn the
	projector on again. If the service lamp turns on again, service
	is required. Visit www.infocus.com/support to contact
	service.

15

Problem

Solution

Result

No start up screen.

Plug the power cord into the projector then press

Correct image.

the power button.

Startup

Screen

Only the start up screen appears.

If your computer is using the projector's DisplayLink

Computer image projected.

connector, see the DisplayLink Software User's

Guide for troubleshooting information.

Press the Source button

to

activate the laptop’s external port.

B

Startup

Screen

Restart laptop

B

16

Problem

Solution

Result

No computer image, just the words “Signal out of

Press the Auto Image button on the keypad or remote. To

Computer image projected.

range.”

adjust computer refresh rate, go to Control Panel > Display >

Settings > Advanced > Adapter (location varies by operating

system).

B

Signal out of the range

You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped.”

Only my laptop’s background appears, not the

DisplayLink - Use DisplayLink software to change the display

Background and Desktop projected.

Desktop icons.

mode from Extended Desktop to Duplicated Desktop.

Windows - Disable “Extend my Windows Desktop” in Control

Panel > Display > Settings > Display 2 (location varies by

operating system).

B	B

Uncheck this option, then click Apply

17

Problem				Solution	Result
Image fuzzy or cropped				Set your computer’s display resolution to the native	Image clear and not cropped.
				resolution of the projector (Start > Settings > Control
				Panel > Display > Settings tab).
						A
			A

For a laptop, disable laptop monitor or turnon dual-display mode

Image not centered on screen.

Adjust Lens Shift in the Basic Picture menu.

Correct image.

B

18

Problem	Solution	Result
Image not square.	Adjust Keystone in the Basic Picture menu.	Square image.

Image not sharp.		Adjust Sharpness in the Basic Picture menu.	Correct image.

Image does not fit 4:3 or 16:9 screen.

Change aspect ratio to 4:3 or 16:9 in Basic	Correct image.
Picture>Aspect Ratio menu.

19