Impex MWM 1801 User Manual

	NOTE:
	Please read all instructions
	carefully before using this
	product
	Table of Contents
	Safety Notice	MARCY HOME GYM
	Hardware Pack
		MWM 1801
	Assembly Instruction
	Parts List
	Resistance Chart
	Warranty
	Ordering Parts
	Model
	MWM 1801
	Retain This
	Manual for
	Reference
	08-18-03	IMPEX FITNESS PRODUCTS
	OWNER'S	14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
	MANUAL	Tel: [phone] Fax: [phone]
		www.impex-fitness.com
		[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN....................................................................................……….. 1

IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 5

HOW TO USE..................................................................................................………. 25 PARTS LIST………………………………………………………………………………….. 26

RESISTANCE CHART………….......................................................................………. 27 WARRANTY.................................................................................................…………. 28 ORDERING PARTS.......................................................................................…………28

BEFORE YOU BEGIN

Thank you for selecting the MARCY MWM 1801 HOME GYM by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our TOO-FREE customer service number. Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number 1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST www.impex-fitness.com [e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1.Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.

2.Only one person at a time should use the machine.

3.If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4.Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.

5.Keep hands away from all moving parts.

6.Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.

7.Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8.Do not place any sharp object around the machine.

9.Disabled person should not use the machine without a qualified person or physician in attendance.

10.Before using the machine to exercise, always do stretching exercises to properly warm up.

11.Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

HARDWARE PACK

4

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Left Base Frame (#3) to the Right Base Frame (#1). Secure them with one Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ¾” Washers (#93), and two M10 Aircraft Nuts (#90).

DIAGRAM 1

5

STEP 2 (See Diagram 2)

A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10 x 2 ½” Carriage Bolts (#82), ¾” Washers (#93), and M10 Aircraft Nuts (#90). NOTE: Do not tighten the Nuts and Bolts yet.

B.) Attach the Right Seat Support (#8) to the Right Base Frame (#1). Secure it with one M10 x 2 ½” Carriage Bolt (#82), ¾” Washer (#93), and M10 Aircraft Nut (#90).

C.) Attach the Right Seat Support (#8) to the Right Vertical Beam (#2). Secure it with one

Bracket (#47), two M10 x 2 ½” Carriage Bolts (#82), two ¾” Washers (#93), and two

M10 Aircraft Nuts (#90).

D.) Attach the Leg Developer (#9) to the Right Seat Support (#8). Secure it with one M10 x 2” Axle (#56), two M10 x ¾” Allen Bolts (#86), and two ¾” Washers (#93). NOTE: Do not over tighten the bolts. Make sure the Leg Developer is able to swivel.

DIAGRAM 2

6

STEP 3 (See Diagram 3)

A.)	Align four 2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame
	(#1). Insert four Guide Rods (#5) through the Rubber Bumpers into the holes on the
	Right Base Frame. Slide two Selector Stems (#35) onto the Guide Rods. Insert a
	Selector Rod (#24) through the hole on each Selector Stem. Secure each Selector
	Rod to the Selector Stem with two M10 x 1” Allen Bolts (#78) and ¾” Washers
	(#93). Please note this machine comes with 18 plates, 9 to each stack. You can
	purchase another 5 more plates (Model no. WK51) in the future to increase the
	weights. It is strongly recommended to spay lubricant such as WD-40 on the two
	Guide Rods to minimize friction.
B.)	Attach the Right Upper Frame (#6) to the top of Right Vertical Beam (#2). Secure it
	with a Pulley Bracket (#46), two M10 x 2 ½” Carriage Bolts (#82), two Ø ¾” Washers
	(#93), and two M10 Aircraft Nuts (#90).
C.)	Attach the Top Socket Assembly (#7) to the four Guide Rods. Make sure the Guide
	Rods are inserted into the holes on the Top Socket Assembly. Secure the Top Socket
	Assembly to the Guide Rods with four M10 x 1” Allen Bolts (#78) and ¾” Washers
	(#93).
D.)	Secure the Top Socket Assembly (#7) to the Right Upper Frame (#6) with two M10 x
	2 3/8” Carriage Bolts (#80), 3/4” Washers (#93) and M10 Aircraft Nuts (#90).
E.)	Carefully tilt over the machine with a help of another person. Secure the Guide Rods
	(#5) to the Right Base Frame (#1) with four ¾” Washers (#93) and M10 x 1” Allen
	Bolts (#78).
F.)	Securely tighten all Nuts and Bolts previously installed.

7

DIAGRAM 3

8