Impex MWB-4360 User Manual

	NOTE:
	Please read all instructions
	carefully before using this
	product
	Table of Contents		®
		MARCY
	Safety Notice	SMITH MACHINE
	Hardware Identifier	MWB-4360
	Assembly Instruction
	Parts List
	Warranty
	Ordering Parts
	Model
	MWB-4360
	Retain This
	Manual for
	Reference
	07-14-06
	OWNER'S
	MANUAL
		IMPEX® INC.
		14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
		Tel: [phone]	Fax: [phone]
		www.impex-fitness.com
		[e-mail]

TABLE OF CONTENTS
BEFORE YOU BEGIN..................................................................…………….	1
IMPORTANT SAFETY NOTICES.................................................................…	2
SMITH MACHINE HARDWARE PACK….......….............................................	4
SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................	6
EXPLODED DIAGRAM…………………………………………………………….	21
SMITH MACHINE PARTS LIST………..…………………………………………	22
MULTI-PURPOSE BENCH HARDWARE PACK………………………………..	23
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS............................	24
EXPLODED DIAGRAM……………………………………………………………	29
MULTI-PURPOSE BENCH PARTS LIST…………………………………………	30
WEIGHT RESISTANCE CHART……………………………………………………	31
WARRANTY.................................................................................................…	32
ORDERING PARTS.....................................................................................…	32

BEFORE YOU BEGIN

Thank you for selecting the MARCY® MWB-4360 by IMPEX® INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our TOLL-FREE customer service number. Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number 1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST www.impex-fitness.com [e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1.Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.

2.Only one person at a time should use the machine.

3.If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4.Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.

5.Keep hands away from all moving parts.

6.Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.

7.Use the machine only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.

8.Do not place any sharp object around the machine.

9.Disabled person should not use the machine without a qualified person or physician in attendance.

10.Before using the machine to exercise, always do stretching exercises to properly warm up.

11.Never operate the machine if the machine is not functioning properly.

12.A spotter is recommended during exercise.

CARE AND MAINTENANCE

1.Lubricate moving parts with WD-40 or light oil periodically.

2.Inspect and tighten all parts before using the machine.

3.The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents.

4.Maximum user’s weight: 300 lbs.

5.Maximum weights on the rack: 600 lbs.

6.Maximum weights on Leg Developer: 100 lbs.

7.Maximum weights on Cross-over, Lat Pull: 200 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL PLACEMENT

The warning labels shown here have been placed on the Rear Base, Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.

3

SMITH MACHINE HARDWARE PACK

4

SMITH MACHINE HARDWARE PACK

5

SMITH MACHINE ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen

Wrenches.

NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Connect the two Base Frames (#1) by a Cross Brace (#2) in the mid-span. Secure each end of The Cross Brace with two M10 x 3 ½” Carriage Bolts (#79), one 4 ¾” x 2” Bracket

(#36), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). B.) NOTE: DO NOT tighten the Nuts and Bolts yet.

DIAGRAM 1

6

STEP 2 (See Diagram 2)

A.) Attach a Front Vertical Frame (#3) to the Right Base Frame (#1). Secure it with two M10 x

3” Carriage Bolts (#76), one 5 1/8” x 2 ¾” Bracket (#34), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts yet.

B.) Align a Ø 2 ½” Rubber Bumper (#59) to the hole on the Base Frame. Insert a Guide Rod (#25) through the Rubber Bumper and into the Base Frame. Secure it with one M10 x 1” Allen Bolt (#68) and Ø ¾” Washer (#66).

C.) Slide a Lower Safety Stop Frame (#92) onto the Guide Rod (#25). Secure the Safety Hook (#93) to the Lower Safety Stop Frame (#92) with a M10 x 1” Allen Bolt (#68) and

M10 Aircraft Nut (#86). Attach the Hook onto the back of the Front Vertical Beam (#3). D.) Slide a Safety Stop Frame (#26) onto the Guide Rod (#25).

E.) Attach the hole on top of the Right Vertical Frame (#5) to the top of the Guide Rod (#25).

Attach the top of Right Vertical Frame (#5) to the top of Front Vertical Frame (#3). Attach the bottom of Right Vertical Frame (#5) to the Base Frame (#1).

F.) Secure the Guide Rod (#25) to the Right Vertical Frame (#5) with one M10 x 1” Allen Bolt (#68) and Ø ¾” Washer (#66).

G.)Secure the Right Vertical Frame (#5) to the Base Frame with two M10 x 3” Carriage Bolts (#76), one 6 ¼” x 2” Bracket (#37), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86). Do not tighten the Nuts and Bolts yet.

H.) Secure the Right Vertical Frame (#5) to the Front Vertical Beam (#3) with one Triangle Bracket (#33), M10 x 3 1/8” Allen Bolt (#72), and ¾” Washer (#66) to the top hole. Secure the bottom two holes with two M10 x 3 3/8” Carriage Bolts (#78), ¾” Washers (#66) and M10 Aircraft Nuts (#86).

I.) Repeat the above Procedures A through H to install the other side.

J.) Attach the Front Top Beam (#15) to the Front Vertical Beams (#3) and the Triangle

Brackets (#33). Align the Holes. Secure each end with two M10 x 3 3/8” Carriage Bolts (#78), Ø ¾” Washers (#66), and M10 Aircraft Nuts (#86).

K.) Do NOT tighten all the Nuts and Bolts yet.

L.) NOTE: Periodically lubricate the two chromed Guide Rods (#25) with WD-40 or light oil to maximize the performance.

7

DIAGRAM 2

8

STEP 3 (See Diagram 3)

A.) Attach the Rear Vertical Beam (#6) to the top of the Cross Brace (#2). Attach the Weight Glide Base (#8) to the Cross Brace from the Bottom. Align the holes. Secure them with two M10 x 3” Carriage Bolts (#76), Ø ¾” Washers (#66), and M10 Aircraft Nuts (#86).

B.) Attach the Pulley Support Frame (#97) to the Rear Vertical Beam. Secure it with two M10 x 2 ¾” Carriage Bolts (#75), one 4 ¾” x 2” Bracket (#36), two Ø ¾” Washers (#66), and two M10 Aircraft Nuts (#86).

C.) Attach the Backrest Board (#38) to the Rear Vertical Beam. Secure it with two M8 x 2 ½”

Allen Bolts (#80) and Ø 5/8” Washers (#65).

9