Impex MP-4500 User Manual

0 (0)

NOTE:

 

Please read all instructions

 

carefully before using this

 

product

 

Table of Contents

MARCY® PLATINUM

Safety Notice

Hardware Pack

CORNER GYM

 

Assembly Instruction

MP-4500

Parts List

 

Resistance Chart

 

Warranty

 

Ordering Parts

 

Model

 

MP-4500

 

Retain This

 

Manual for

 

Reference

 

10-25-06

IMPEX® INC.

 

OWNER'S

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

MANUAL

www.impex-fitness.com

 

info@impex-fitness.com

TABLE OF CONTENTS

 

BEFORE YOU BEGIN......................................................................................

1

IMPORTANT SAFETY NOTICES.....................................................................

2

HARDWARE PACK……….....….......................................................................

4

ASSEMBLY INSTRUCTIONS...............................................................…..........

7

PARTS LIST…………………………………………………………….……….…….

34

RESISTANCE CHART……………………………………………………………….

35

WARRANTY.................................................................................................…

36

ORDERING PARTS.........................................................................................

36

BEFORE YOU BEGIN

Thank you for selecting the MARCY PLATINUM MP-4500 CORNER GYM by IMPEX® INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. To avoid unnecessary delays, please call our TOLL-FREE customer service number. Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number 1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST www.impex-fitness.com info@impex-fitness.com

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions:

1.Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine.

2.Only one person at a time should use the same station.

3.If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4.Position the machine on a clear, leveled surface. DO NOT use the machine near water or outdoors.

5.Keep hands away from all moving parts.

6.Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing that could become caught in the machine. Running or aerobic shoes are also required when using the machine.

7.Use the machine only for its intended use as described in this manual. DO

NOT use attachments not recommended by the manufacturer.

8.Do not place any sharp object around the machine.

9.Disabled person should not use the machine without a qualified person or physician in attendance.

10.Before using the machine to exercise, always do stretching exercises to properly warm up.

11.Never operate the machine if the machine is not functioning properly.

CARE AND MAINTENANCE

1.Lubricate moving parts with WD-40 or light oil periodically.

2.Inspect and tighten all parts before using the machine.

3.The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents.

4.Maximum user’s weight: 300 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL REPLACEMENT

The warning labels shown here have been placed on the Left Base Frame and Left Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.

3

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

4

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

5

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

6

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches

NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury.

STEP 1 (See Diagram 1)

A.)

Place the Right Base Frame (#31) on a flat surface. Make sure there is enough space

 

around to assemble the machine.

B.)

Insert four Guide Rods (#16) into the holes on the Right Base Frame. Secure each

 

Guide Rod from bottom with a M10 x ¾” Allen Bolt (#95) and Ø ¾” Washer (#100).

C.)

Attach four Ø 2 3/8” x 1” Rubber Bumpers (#52) to top of the Guide Rods then slid down

 

to the stopper on the Guide Rods.

D.)

Attach the Right Vertical Frame (#4) onto the Right Base Frame. Secure it with two M10

 

x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100),

 

and two M10 Aircraft Nuts (#102).

E.)

Attach the Butterfly Base (#13) to the Right Base Frame (#31). Attach the Front Base

 

Frame (#12) to the Butterfly Base (#13) from the front. Align the holes and secure them

 

together with two M10 x 3 ¾” Carriage Bolts (#97) from side, two M10 x 2 ¾” Carriage

 

Bolts (#98) from the bottom, four Ø ¾” Washers (#100), and four M10 Aircraft Nuts

 

(#102).

F.)

Slide fourteen Weight Plates (#80) onto the rear set of Guide Rods. Make sure the

 

groove on the plates all face toward the back of the machine.

G.)

Insert a Selector Rod (#28) into the center holes. Slide a Selector Stem (#81) onto the

 

two Guide Rods.

H.)

Insert a Weight Selector Pin (#74) to select the number of weight plates. Each Weight

 

Plate weights approximately 10 lbs. Please refer to the Weight Resistance Chart in page

 

35.

I.)

Repeat procedures F, G and H above to install the other fourteen Weight Plates onto the

 

front two Guide Rods.

J.)

Attach the Foot Plate (#17) to the Front Base Frame (#12). Secure it with the Foot Plate

 

Axle (#18).

7

DIAGRAM 1

8

STEP 2 (See Diagram 2)

A.) Attach the Right Upper Frame (#1) onto the Right Vertical Frame (#4). Secure it with two M10 x 2

¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10 Aircraft Nuts (#102). Do not tighten the Nuts and Bolts yet.

B.) Attach the Right Upper Frame to the four Guide Rods (#16). Secure it to each Guide Rod with one M10 x ¾” Allen Bolt (#95) and Ø ¾” Washer (#100).

C.) Securely tighten the Nuts and Bolts previously installed.

D.) Attach the Right Seat Support (#7) to the Right Vertical Frame (#4). Secure it with two M10 x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10

Aircraft Nuts (#102).

E.) Attach the Leg Developer (#8) to the open bracket on the Right Seat Support. Secure it with one Axle (#15), two M10 x ¾” Allen Bolts (#95), and two Ø ¾” Washers (#100).

9

STEP 3 (See Diagram 3)

A.) Attach the Front Press Base (#2) to the Right Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” x Ø 3/8” Washers (#70), and two M10 Aircraft Nuts (#102). Do not over tighten the Nuts; make sure the Base is able to swivel.

B.) Attach the Front Press (#3) to the Front Press Base (#2). Secure it with one 7 5/8” Front Press Axle (#30), two Ø 1 ¼” x Ø 3/8” Washers (#70), and two M10 Aircraft Nuts (#102).

Do not over tighten the Nuts; make sure the Press Arm is able to swivel.

C.) Thread the Short T-shaped Lock Pin (#78) into the tube on the Front Press to obtain the desired Front Press position.

D.) Attach the Backrest Board (#43) to the Backrest Support Frame (#5). Secure it with two M8 x 1 5/8” Allen Bolts (#85) and Ø 5/8” Washers (#101).

E.) Attach the Backrest Support Frame (#5) to the Right Vertical Frame (#4). Secure it with one M10 x 4 3/8” Allen Bolt (#89), two Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102).

F.) Thread a Long T-shaped Lock Pin (#77) into the hole on the Right Vertical Frame to obtain the desired Backrest position.

10

Impex MP-4500 User Manual

DIAGRAM 3

11

Loading...
+ 25 hidden pages