IBM 8416, 8418, 8184, 8419, 8417 User Manual

...
0 (0)

ThinkCentre

 

Hardware Maintenance Manual Types 8127, 8183, 8184, 8320, 8416, 8417, 8418, 8419, and 8429

ThinkCentre

 

Hardware Maintenance Manual Types 8127, 8183, 8184, 8320, 8416, 8417, 8418, 8419, and 8429

Note: Before using this information and the product it supports, be sure to read the general information under “Notices” on page 187.

Sixth Edition (February 2005)

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS ISWITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE LIMITED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimers or express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements or changes in the products or the programs described in this publication at any time.

Requests for technical information about IBM products should be made to your IBM Authorized Dealer or your IBM Marketing Representative.

© Copyright International Business Machines Corporation 2005. All rights reserved.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.

Contents

Chapter 1. About this manual . . . .

.

1

Replacing the battery . . . . . . . . . .

.

31

Important Safety Information . . . . . . . .

.

1

Replacing the power supply . . . . . . . .

.

32

Strategy for Replacing FRUs for CTO, CMV, and

 

 

Replacing the system board, microprocessor, and

 

 

 

GAV products . . . . . . . . . . . . .

.

2

heat sink . . . . . . . . . . . . . .

.

34

Product definition . . . . . . . . . .

.

2

Replacing the microprocessor . . . . . .

.

38

FRU Identification for CTO, CMV, and GAV

 

 

Replacing internal drives . . . . . . . . .

. 38

products . . . . . . . . . . . . . .

. 3

Replacing a CD-ROM, CD-RW, or DVD optical

 

 

 

 

 

drive . . . . . . . . . . . . . .

.

40

Chapter 2. General information . . . .

.

5

Replacing the hard disk drive . . . . . .

.

40

Access IBM . . . . . . . . . . . . . . .

5

Connecting a serial ATA hard disk drive. .

. . 41

Replacing the diskette drive . . . . . . .

.

42

Additional information resources . . . . . .

.

5

Connecting an IDE hard disk or CD drive . .

. 42

Features . . . . . . . . . . . . . . . .

5

Replacing the speaker . . . . . . . . . .

.

43

Specifications . . . . . . . . . . . . . .

9

Replacing the power button and LED assembly .

. 43

 

 

 

Chapter 3. General Checkout . . . . .

11

Replacing the fan assembly . . . . . . . .

.

44

Closing the cover and connecting the cables . .

. 46

 

 

 

Chapter 4. IBM Enhanced Diagnostics

13

Chapter 7. Symptom-to-FRU Index . .

 

. 47

Diagnostics program download. . . . . . .

. 13

Hard disk drive boot error . . . . . . . .

.

47

Running IBM Enhanced Diagnostics from the Access

 

 

Power Supply Errors . . . . . . . . . .

.

47

IBM Predesktop Area . . . . . . . . . .

.

13

Diagnostic error codes . . . . . . . . . .

.

49

Navigating through the diagnostics programs . . . 13

Beep symptoms . . . . . . . . . . . .

.

70

Running diagnostics tests. . . . . . . . .

.

13

No-beep symptoms . . . . . . . . . . .

.

72

Test selection . . . . . . . . . . . .

.

14

POST error codes . . . . . . . . . . .

.

73

Test results . . . . . . . . . . . .

.

14

Miscellaneous error messages . . . . . . .

.

87

Fixed disk advanced test (FDAT) . . . . .

. 15

Undetermined problems . . . . . . . . .

.

89

Quick and Full erase - hard drive . . . . .

.

16

 

 

 

 

Viewing the test log . . . . . . . . . .

.

17

Chapter 8. Parts listing . . . . . . .

 

.

91

 

 

 

 

Chapter 5. Using the IBM Setup Utility

19

Machine Type 8127 . . . . . . . . . . .

.

91

Machine Type 8183 . . . . . . . . . . .

.

95

Starting the IBM Setup Utility program . . . .

. 19

Machine Type 8184 . . . . . . . . . .

 

.

109

Viewing and changing settings . . . . . . .

.

19

 

Machine Type 8320 . . . . . . . . . .

 

.

116

Exiting from the IBM Setup Utility program . .

. 19

 

Machine Type 8416 . . . . . . . . . .

 

.

125

Using passwords . . . . . . . . . . .

.

19

 

Machine Type 8417 . . . . . . . . . .

 

.

127

User password . . . . . . . . . . .

.

19

 

Machine Type 8418 . . . . . . . . . .

 

.

133

Administrator password . . . . . . . .

.

20

 

Machine Type 8419 . . . . . . . . . .

 

.

137

Setting, changing, and deleting a password . . . 20

 

Machine Type 8429 . . . . . . . . . .

 

.

141

Security settings for Access IBM Predesktop Area. . 20

 

 

 

 

 

Using Security Profile by Device . . . . . .

.

21

Chapter 9. Additional Service

 

 

 

Using IDE Drives Setup . . . . . . . . .

.

21

 

 

 

Information . . . . . . . . . . .

. 145

Selecting a startup device. . . . . . . . .

.

22

Security features . . . . . . . . . . .

 

.

145

Selecting a temporary startup device . . . .

.

22

 

Passwords . . . . . . . . . . . .

. 145

Changing the startup device sequence . . .

. 22

Erasing a lost or forgotten password (clearing

 

 

 

Advanced settings . . . . . . . . . . .

.

22

 

 

 

CMOS) . . . . . . . . . . . . .

 

.

146

 

 

 

 

Chapter 6. Replacing FRUs . . . . . .

23

Vital product data . . . . . . . . . .

 

.

146

Management Information Format (MIF) . .

 

. 147

Locating controls and connectors on the front of the

 

 

 

 

 

BIOS levels . . . . . . . . . . . . .

 

.

147

computer . . . . . . . . . . . . . .

.

23

 

Flash update procedures. . . . . . . . .

 

.

148

Locating connectors on the rear of the computer .

. 24

 

Updating (flashing) BIOS from a diskette . .

 

. 148

Opening the cover . . . . . . . . . . .

.

25

 

Updating (flashing) BIOS from your operating

 

 

 

Locating components . . . . . . . . . .

.

26

 

 

 

system . . . . . . . . . . . . .

 

.

148

Accessing system board components and drives .

. 27

 

Recovering from a POST/BIOS update failure

 

 

148

Identifying parts on the system board . . . .

. 28

 

 

Power management . . . . . . . . . .

 

.

150

Replacing memory . . . . . . . . . . .

.

29

 

Automatic configuration and power interface

 

 

 

Replacing a PCI adapter . . . . . . . . .

.

30

 

 

 

(ACPI) BIOS. . . . . . . . . . . .

 

.

150

 

 

 

 

© Copyright IBM Corp. 2005

 

 

 

 

 

iii

Advanced Power Management . . . .

.

.

150

Electrical safety. . . . . . . . . .

.

.

154

Automatic Hardware Power Management

 

 

 

Safety inspection guide . . . . . . .

.

. 155

features . . . . . . . . . . . .

.

.

150

Handling electrostatic discharge-sensitive

 

 

 

Setting Automatic Hardware Power

 

 

 

devices . . . . . . . . . . . .

.

.

156

Management features. . . . . . . .

.

.

150

Grounding requirements . . . . . .

.

.

157

Automatic Power-On features . . . . .

.

.

151

Safety notices (multi-lingual translations) .

.

.

157

 

 

 

 

Send us your comments! . . . . . . .

.

.

186

Chapter 10. Related service

 

 

 

Problem determination tips. . . . . . .

.

.

187

information . . . . . . . . . . .

.

153

Notices . . . . . . . . . . . . .

.

.

187

Safety information. . . . . . . . . .

.

.

153

Trademarks . . . . . . . . . . . .

.

.

188

 

 

 

 

General safety . . . . . . . . . .

.

.

153

 

 

 

 

iv Hardware Maintenance Manual

Chapter 1. About this manual

This manual contains service and reference information for IBM® computer Types 8127, 8183, 8184, 8320, 8416, 8417, 8418, 8419 and 8429.

This manual is divided into product service sections and a related service section, as follows:

vThe product service sections include procedures for isolating problems to a FRU, a Symptom-to-FRU Index, additional service information and an illustrated parts catalog.

vThe related service section includes safety notices and safety information, and problem determination tips.

Note:

This manual is intended for trained servicers who are familiar with IBM Personal Computer products. Use this manual along with advanced diagnostic tests to troubleshoot problems effectively.

Before servicing an IBM product, be sure to review the “Safety information” on page 153.

Important Safety Information

Be sure to read all caution and danger statements in this book before performing any of the instructions.

Prenez connaissance de toutes les consignes de type Attention et Danger avant de procéder aux opérations décrites par les instructions.

Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen.

Accertarsi di leggere tutti gli avvisi di attenzione e di pericolo prima di effettuare qualsiasi operazione.

© Copyright IBM Corp. 2005

1

IBM 8416, 8418, 8184, 8419, 8417 User Manual

Leia todas as instruções de cuidado e perigo antes de executar qualquer operação.

Lea atentamente todas las declaraciones de precaución y peligro ante de llevar a cabo cualquier operación.

Strategy for Replacing FRUs for CTO, CMV, and GAV products

Product definition

Dynamic Configure To Order (CTO)

This provides the ability for a customer to configure an IBM solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, PC Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = ’CTO’ (Example: 1829-CTO).

Custom Model Variant (CMV)

This is a unique configuration that has been negotiated between IBM and the customer. A unique 4-digit MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special bid offering. Therefore, it is NOT generally announced.

2 Hardware Maintenance Manual

vThe MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = ’CTO’ (Example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV model (Example: 1829-W15).

vThe PEW record is the 4-digit MT and 3-digit model, where model = ’CTO’ (Example: 1829-CTO).

veSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15 will be found on the eSupport site.)

vThe HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are custom models and are not found in the HMM.

General Announce Variant (GAV)

This is a standard model (fixed configuration). GAVs are announced and offered to all customers. The MTM portion of the machine label is a 4-digit MT and 3-digit model, where model = a “fixed model number”, not ’CTO’ (Example: 1829-F1U). Also, PEW, eSupport, and the HMM will list these products under the same fixed model number.

FRU Identification for CTO, CMV, and GAV products

There are three information resources to identify which FRUs are used to support CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM.

Using PEW

vPEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities for CTO, CMV and GAV products at a MT - serial number level. An example of key commodities are hard disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.

vRemember, All CTO and CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where model = ’CTO’ (Example: 1829-CTO). GAVs are loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed model number”, not ’CTO’ (Example: 1829-F1U).

vPEW can be accessed at the following Web site: http://w3-3.ibm.com/pc/entitle

Click on MACHINE LOOKUP, followed by WARRANTY INFORMATION. Input the MT and Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION.

vBusiness Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS.

vAuthorized IBM Business Partners can access Eclaim at the following Web site: http://wca.eclaim.com

Using eSupport

For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory)

veSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW).

veSupport can be accessed at the following Web site: http://www.ibm.com/pc/support

vTo view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP. Type in the model type and serial number. The key commodities will be returned in the eSupport record under PARTS SHIPPED WITH YOUR SYSTEM.

Chapter 1. About this manual 3

For the Remaining FRUs (the complete list of FRUs at the MT Model level)

veSupport can be used to view the complete list of FRUs for a machine type and model.

vTo view the complete list of FRUs, type in the machine type and model (Example: 1829-CTO) under QUICK PATH. Under ’View by Document Type’ select PARTS INFORMATION. Under ’Filter by Category’ select SERVICE PARTS. Under ’Parts Information by Date’ select SYSTEM SERVICE PARTS. The list of service parts by description, with applicable machine type model and FRU will be displayed.

Using the HMM

vUse the HMM as a back-up to PEW and eSupport to view the complete list of FRUs at the MT Model level.

4 Hardware Maintenance Manual

Chapter 2. General information

Access IBM

To find more information about the features on the computer you can use the Access IBM Predesktop Area. To open the Access IBM Predesktop Area, use the following procedure:

1.Shut down the operating system and turn off the computer.

2.Turn on the computer and look for the following prompt on the logo screen:

(To interrupt normal startup, press Enter)

Press Enter when you see the prompt.

3.The Access IBM Predesktop Area opens.

Additional information resources

If you have Internet access, the most up-to-date information for your computer is available from the World Wide Web.

You can find the following information:

vCRU removal and installation instructions

vPublications

vTroubleshooting information

vParts information

vDownloads and drivers

vLinks to other useful sources of information

To access this information, point your browser to:

http://www.ibm.com/pc/support/site.wss/document.do?Lndocid=part-video

Features

This section provides an overview of the computer features and preinstalled software.

Microprocessor

vIntel® Celeron(some models)

vIntel Pentium® 4 (some models)

vIntel Pentium 4 with HyperThreading (some models)

vInternal cache (size varies by model type)

Memory

Support for two 184-pin dual inline memory modules (DIMMs). Each DIMM socket can support up to 1 GB of PC2700 double data rate (DDR) dynamic random access memory (SDRAM) for a system maximum of 2 GB.

Internal drives

v3.5-inch, half-inch (slim) diskette drive (some models)

vHard disk drive

vOptical drives such as CD-ROM, DVD-ROM, DVD-ROM/CD-RW Combo, CD-RW, or IBM Multi-Burner (some models)

© Copyright IBM Corp. 2005

5

Video subsystem

An integrated Intel Extreme Graphics 2 controller for a Video Graphics Array (VGA) monitor

Audio subsystem

The integrated AC’97 audio controller provides four audio connectors.

vMicrophone and headphone connectors on the front panel

vLine-in and line-out connectors on the rear panel

Connectivity

v10/100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN® feature (some models)

v10/100/1000 Mbps integrated Intel Ethernet controller that supports the Wake on LAN feature (some models)

vPeripheral Component Interconnect (PCI) V.90 Data/Fax modem (some models)

System management features

vRemote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)

vWake on LAN

vWake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal PCI modem)

vRemote Administration

vAutomatic power-on startup

vSystem Management (SM) BIOS and SM software

vAbility to store POST hardware test results

Input/output features

v25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)

vTwo 9-pin serial connectors

vEight USB 2.0 connectors (two on front panel and six on rear panel)

vPS/2® mouse connector

vPS/2 keyboard connector

vEthernet connector

vVGA monitor connector

vTwo audio connectors (line-in and line-out) on rear panel

vTwo audio connectors (microphone and headphone) on front panel

Expansion

vTwo 32-bit PCI full height adapter slots

vTwo DIMM memory connectors

Power

v200 Watt power supply with manual voltage selection switch

vAutomatic 50/60 Hz input frequency switching

vAdvanced Power Management support

vAdvanced Configuration and Power Interface (ACPI) support

Security features

6 Hardware Maintenance Manual

vUser and administrator passwords

vSupport for the addition of a cable lock such as a Kensington lock

vKnockout holes for installing a rope clip (U-bolt)

vOptional keylock on top cover

vStartup sequence control

vStartup without diskette drive, keyboard, or mouse

vDiskette and hard disk I/O control

vSerial and parallel port I/O control

vSecurity profile by device

IBM preinstalled software

The computer comes with preinstalled software. An operating system, device drivers to support built-in features, and other support programs are included.

Chapter 2. General information 7

Operating systems (preinstalled) (varies by model)

Note: Not all countries or regions will have these operating systems.

vMicrosoft® Windows® XP Home

vMicrosoft Windows XP Professional

vMicrosoft Windows 2000

8 Hardware Maintenance Manual

Specifications

This section lists certain specifications for the computer. For the latest specification information, see the User Guide for the computer go to:

http://www.ibm.com/pc/support/

Dimensions

Width: 12.2 inches (310 mm)

Height: 3.35 inches (85 mm)

Depth: 14.1 inches (358 mm)

Weight

Minimum configuration as shipped: 8.3 kg (18.4 lbs) With stand: 8.5 kg (18.8 lbs)

Environment

Air temperature:

Operating at 0 - 3000 ft (914.4 m): 10° to 35°C (50° to 95°F)

Operating at 3000 ft - 7000 ft (2134 m): 10° to 32°C (50° to 89.6°F)

Non-operating: 10° to 43°C (50° to 110°F)

Humidity:

Operating: 8% to 80%

Non-operating: 8% to 80%

Transit: 8% to 90%

Maximum altitude: 7000 ft (2133.6 m)

Electrical input

Input voltage:

Low range:

Minimum: 90 V ac

Maximum: 137 V ac

Input frequency range: 57–63 Hz

Voltage switch setting: 115 V ac

High range:

Minimum: 180 V ac

Maximum: 265 V ac

Input frequency range: 47–53 Hz

Voltage switch setting: 230 V ac

Input kilovolt-amperes (kVA) (approximate):

Minimum configuration as shipped: 0.09 kVA

Maximum configuration: 0.23 kVA

Heat output (approximate) in British thermal units (Btu) per hour:

Minimum configuration: 205.8 Btu/hr (60 watts)

Maximum configuration: 548.8 Btu/hr (160 watts)

Airflow for computers with a microprocessor that runs at or below 2.8 GHz

Approximately 13 cubic feet (0.37 cubic meters) per minute

Airflow for computers with a microprocessor that runs above 2.8 GHz

Approximately 14 cubic feet (0.40 cubic meters) per minute

Acoustical noise-emission values

Note: In this computer, fan speed is controlled by temperature, configuration, and software. Actual noise-emission values might be different from the stated values depending on the number of fans and the speed of the fans.

Average sound-pressure levels for computers with a microprocessor that runs at or below 2.8 GHz:

At operator position - 0.5 meters:

Idle: 30 dBA

Operating: 34 dBA

At bystander position - 1 meter (3.3 ft):

Idle: 25 dBA

Operating: 29 dBA

Declared (upper limit) sound-power levels:

Idle: 3.9 bels

Operating: 4.3 bels

Average sound-pressure levels for computers with a microprocessor that runs at or greater than 2.8 GHz:

At operator position - 0.5 meters:

Idle: 31 dBA

Operating: 34 dBA

At bystander position - 1 meter (3.3 ft):

Idle: 26 dBA

Operating: 29 dBA

Declared (upper limit) sound-power levels:

Idle: 4.0 bels

Operating: 4.3 bels

Note: These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate.

Chapter 2. General information 9

10 Hardware Maintenance Manual

Chapter 3. General Checkout

This general checkout procedure is for Type 8127, 8183, 8184, 8320, 8416, 8417, 8418, 8419, and 8429 computers.

Attention

The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving or formatting. Data or programs can be overwritten if you select an incorrect drive.

Diagnostic error messages appear when a test program finds a problem with a hardware option. For the test programs to properly determine if a test Passed, Failed or Aborted, the test programs check the error-return code at test completion. See “Diagnostic error codes” on page 49.

General error messages appear if a problem or conflict is found by an application program, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.

Notes:

vThe default for this computer is to boot up quiet (no beep and no memory count and checkpoint code display) when no errors are detected by POST.

vTo enable beep and memory count and checkpoint code display when a successful POST occurs, do the following:

1.Select Start Options in the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19).

2.Set Power-On Self-Test to Enhanced.

vBefore replacing any FRUs, ensure that the latest level of BIOS is installed on the system. A down-level BIOS might cause false errors and unnecessary replacement of the system board. For more information on how to determine and obtain the latest level BIOS, see “BIOS levels” on page 147.

vIf multiple error codes are displayed, diagnose the first error code displayed.

vIf the computer hangs with a POST error, go to Chapter 7, “Symptom-to-FRU Index,” on page 47.

vIf the computer hangs and no error is displayed, go to “Undetermined problems” on page 89.

vIf an installed device is not recognized by the diagnostics program, that device might be defective.

001

1.Power-off the computer and all external devices.

2.Check all cables and power cords.

3.Make sure the system board is seated properly.

4.Set all display controls to the middle position.

5.Power-on all external devices.

6.Power-on the computer.

7.Check for the following response:

© Copyright IBM Corp. 2005

11

v Readable instructions or the Main Menu.

DID YOU RECEIVE THE CORRECT RESPONSE?

If NO, continue to 002 .

If YES, proceed to 003 .

002

If the Power Management feature is enabled, do the following:

1.Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19)

2.Select Power Management from the IBM Setup Utility program menu.

3.Select APM.

4.Be sure APM BIOS Mode is set to Disabled. If it is not, press Left Arrow () or Right Arrow () to change the setting.

5.Select Automatic Hardware Power Management.

6.Set Automatic Hardware Power Management to Disabled.

7.If the problem persists, continue to 003 .

003

Run the Diagnostic programs. See Chapter 4, “IBM Enhanced Diagnostics,” on page 13.

vIf you receive an error, replace the part that the diagnostic program calls out or go to “Diagnostic error codes” on page 49.

vIf the test stops and you cannot continue, replace the last device tested.

12 Hardware Maintenance Manual

Chapter 4. IBM Enhanced Diagnostics

The IBM Enhanced Diagnostics program uses a full range of diagnostic utilities to determine the operating condition of the computer’s hardware components.

You can run the IBM Enhanced Diagnostics from the Access IBM Predesktop Area on your hard disk. Alternatively, you can create a bootable IBM Enhanced Diagnostics diskette from the Access IBM Predesktop Area.

You can also download the latest version of the Enhanced Diagnostics program from

http://www.ibm.com/pc/support/

on the World Wide Web. Type your machine type and model number into the Quick Path field to find the downloadable files that are specific to the computer.

Diagnostics program download

To download the Diagnostics program, do the following:

vGo to http://www.ibm.com/.

vSelect Support & downloads.

vSelect Personal computing from the Get product support forlist.

vEnter your machine type in the Quick Pathbox and click Go.

vFollow the links provided to locate the IBM Enhanced Diagnostics.

Note: You can download either a diskette image or a startable CD-ROM image (.iso file) of the diagnostics.

Running IBM Enhanced Diagnostics from the Access IBM Predesktop Area

To open the Access IBM Predesktop Area, do the following:

1.With the computer off, press and hold the Enter key; then, turn on the computer.

2.When the logo screen appears, release the Enter key.

3.The Access IBM Predesktop Area opens.

4.Select Run diagnostics from the Utilities menu.

5.Follow the instructions on the screen.

Navigating through the diagnostics programs

Use the cursor movement keys to navigate within the menus.

vThe Enter key is used to select a menu item.

vThe Esc key is used to back up to the previous menu.

vFor online help select F1.

Running diagnostics tests

There are four ways to run the diagnostic tests.

© Copyright IBM Corp. 2005

13

1.Using the cursor movement keys, highlight Run Normal Test or Run Quick Test from the Diagnostics menu and then press Enter.

This will automatically run a pre-defined group of tests from each test category. Run Normal Test runs a more extensive set of tests than does Run Quick Test and takes longer to execute.

2.Press F5 to automatically run all selected tests in all categories. See “Test selection.”

3.From within a test category, press Ctrl-Enter to automatically run only the selected tests in that category. See “Test selection.”

4.Using the cursor movement keys, highlight a single test within a test category, then press Enter. This will run only that test.

Press Esc at any time to stop the testing process.

Test results, (N/A, PASSED, FAILED, ABORTED), are displayed in the field beside the test description and in the test log. See “Viewing the test log” on page 17.

Test selection

To select one or more tests, use the following procedure.

1.Open the corresponding test category.

2.Using the cursor movement keys, highlight the desired test.

3.Press the space bar.

A selected test is marked by >>. Pressing the space bar again de-selects a test and removes the chevron.

4.Repeat steps 2 and 3 above to select all desired tests.

Test results

Diagnostics test results will produce the following error code format:

Function

Failure Type DeviceID

Date

ChkDigits

Text

Code

 

 

 

 

 

 

 

 

 

vFunction Code:

Represents the feature or function within the PC.

vFailure Type:

Represents the type of error encountered.

vDeviceID:

Contains the component’s unit-ID which corresponds to either a fixed disk drive, removable media drive, serial or parallel port, processor, specific RIMM, or a device on the PCI bus.

vDate:

Contains the date on which the diagnostic test was run. The date is retrieved from CMOS and displayed using the YYYYMMDD format.

vChkDigits:

Contains a 2-digit check-digit value to ensure the following:

Diagnostics were run on the specified date.

Diagnostics were run on the specified IBM computer.

The diagnostic error code is recorded correctly.

vText:

14 Hardware Maintenance Manual

Description of the error.

Note: See “Diagnostic error codes” on page 49 for error code listings.

Fixed disk advanced test (FDAT)

PC-Doctor’s (PCDR) Fixed-Disk Advanced Test module (FDAT) is a full-featured highly configurable fixed-disk test suite. The configurable capabilities of FDAT allow users to enable or disable specific tests, enable or disable testing features, control the test log detail, alter testing parameters, etc. FDAT will test for and report most commonly found errors on a fixed-disk drive and is able to test up to 128 SCSI and 4 IDE drives (up to 132 total drives).

Drive information is gathered through FDAT’s enumeration of available devices and user specific configuration parameters located in the FDAT.INI. FDAT uses information supplied by these features to indicate specifically what devices are available for test, what tests are available for the device, device properties, etc.

Modify the FDAT.INI file in PC Doctor for DOS to change testing parameters.

FDAT consists of the following subtests and features.

Fixed-Disk Tests:

vSeek Tests: - checks the physical operation of the drive head.

Linear Seek

Random Seek

Min-Max Seek

Butterfly Seek

vVerify Tests: - checks the integrity of the data present on the media.

Linear Verify

Random Verify

vSurface Scan Tests: - checks the drive media for defects.

Surface Scan (Linear)

Surface Scan (Aggressive) - this is disabled for normal customer use.

Surface Scan (Random)

vSMART: - checks the SMART functionality for drives that support SMART.

Start SMART Self-Test

Get SMART test results

Other Test Features:

vWrite-Splice Repair - detects and corrects Error Correction Code errors during Verify tests.

vAuto Spin Down - a gradual spin down of the drive platters to avoid damaging the media.

vManufacturer Log - an in-depth manufacturer supported log of errors on the drive.

Multitasking:

To allow simultaneous testing of multiple hard drives whenever possible, the FDAT module is written as a set of multitasking functions. Each drive under test can run the same test or run a different test at the same time. Each subtest is written to handle a single test pass and all test variables are kept track of in a

Chapter 4. IBM Enhanced Diagnostics 15

structure unique for each drive. However, when testing IDE drives, FDAT will not perform simultaneous testing of IDE drives that are attached to the same IDE cable. For example, if FDAT is testing four IDE drives on a PC, it will perform simultaneous testing on drives 1 and 3 first (master drives), then perform tests on 2 and 4 (slave drives). FDAT will also perform simultaneous testing on a master and slave that are on separate IDE cables, but will not perform simultaneous tests on a master and slave on the same IDE cable. This generally increases the amount of time needed to test multiple IDE drives.

Another limitation of FDAT’S multitasking capability is the use of Ultra DMA (UDMA). Only one drive at a time can access the UDMA channel and the UDMA channel buffer must be kept high in order to maintain a speed advantage over other data transfer modes. In order to use the UDMA channel during testing, users must disable the multitasking feature.

Destructive vs non-destructive testing:

Most of the tests found in FDAT are non-destructive. This means that PCDR will preserve any data that is present on the tested media prior to beginning any destructive operations (i.e. write operations). However, users can run certain tests in destructive mode (i.e. surface scan tests). Destructive tests will speed up testing because FDAT does not preserve the data on the media prior to the test beginning. Unlike non-destructive tests, any data present on the media prior to the test beginning is lost.

FDAT allows for enabling or disabling destructive tests, as well as specifying a range of destructive and non-destructive sectors on the tested drive. This is done through the configuration of the FDAT.INI.If destructive and non-destructive ranges somehow overlap, then the overlapped area is considered non-destructive. For example, if users specify both destructive and non-destructive ranges as the same, then the entire drive is tested as non-destructive.

Quick and Full erase - hard drive

The Diagnostics program offers two hard drive format utilities:

vQuick Erase Hard Drive

vFull Erase Hard Drive

The Quick Erase Hard Drive provides a DOS utility that performs the following steps.

vDestroys the Master Boot Record (MBR) on the hard drive.

vDestroys all copies of the FAT Table on all partitions (both the master and backup).

vDestroys the partition table.

vProvides messages that warn the user that this is a non-recoverable process.

16 Hardware Maintenance Manual

The Full Erase Hard Drive provides a DOS utility that performs the following steps.

vPerforms all the steps in Quick Erase.

vProvides a DOS utility that writes random data to all sectors of the hard drive.

vProvide an estimate of time to completion along with a visual representation of completion status.

vProvides messages that warn the user about non-recoverable process.

Important: Make sure that all data is backed up before using the Quick or Full Erase functions.

To select the Quick Erase or Full Erase Hard Drive utility, use the following procedure.

1.Select the UTILITY option on the toolbar and press Enter.

2.Select either the QUICK ERASE or FULL ERASE HARD DISK option and follow the instructions.

Viewing the test log

Errors reported by the diagnostic test will be displayed by the program as a failed test.

To view details of a failure or to view a list of test results, use the following procedure from any test category screen.

vPress F3 to activate the log file.

vPress F3 again to save the file to diskette or F2 to print the file.

Chapter 4. IBM Enhanced Diagnostics 17

18 Hardware Maintenance Manual

Chapter 5. Using the IBM Setup Utility

The IBM Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of the computer. The IBM Setup Utility program is used to view and change the configuration settings of the computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the IBM Setup Utility program.

Starting the IBM Setup Utility program

To start the IBM Setup Utility program, do the following:

1.Shut down the operating system and turn off the computer.

2.Turn on the computer and look for the following prompt on the logo screen:

(To interrupt normal startup, press Enter)

Press Enter when you see the prompt.

3.When the Access IBM Predesktop Area displays, double click Start setup utility.

Note: If an administrator password has been set, the IBM Setup Utility program menu is not display until you type your password.

The IBM Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in the computer.

Viewing and changing settings

The IBM Setup Utility program menu lists items that identify system configuration topics.

When working with the IBM Setup Utility program menu, you must use the keyboard. The keys used to perform various tasks are displayed at the bottom of each screen.

Exiting from the IBM Setup Utility program

When you finish viewing or changing settings, press Esc to return to the IBM Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save Settings or Save and exit the Setup Utility. Otherwise, your changes will not be saved.

Using passwords

You can use passwords to provide security for the computer and data. There are two kinds of passwords: a user password and an administrator password. You do not have to set a password of either type to use the computer. However, if you decide to set either one, read the following sections.

User password

The user password feature deters unauthorized persons from gaining access to the computer.

© Copyright IBM Corp. 2005

19

Administrator password

Setting an administrator password deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set an administrator password.

After you set an administrator password, a password prompt is displayed each time you try to access the IBM Setup Utility program. If you type the wrong password, you will see an error message. If you type the wrong password three times, you must turn the computer off and start again.

If both the user and administrator passwords are set, you can type either password. However, to change any configuration settings, you must use your administrator password.

Setting, changing, and deleting a password

To set, change, or delete a password, do the following:

Note: A password can be any combination of up to seven characters (A- Z, a-z, and 0-9).

1.Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19).

2.From the IBM Setup Utility program menu, select Security Set Passwords. Read the information displayed on the right side of the screen.

Security settings for Access IBM Predesktop Area

The security settings in the IBM Setup Utility allow you to select the level of security that you require for the Access IBM Predesktop Area. These setting are described below:

Secure

This setting does not allow any user or software initiated changes.

Normal

This setting allows the user to make changes but the contents are hidden from the operating system.

Disabled

This setting provides the lowest level of security. The area can be changed by the user or the operating system.

To set the security level for the Access IBM Predesktop Area, do the following:

1.Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19).

2.From the IBM Setup Utility program menu, select Security.

3.Select Access IBM Predesktop Area.

4.Select the desired setting and press Enter.

5.Return to the IBM Setup Utility program menu and select Exit and then Save Settings or Save and exit the Setup Utility.

Note: If you do not want to save the settings, select Exit the Setup Utility without saving.

20 Hardware Maintenance Manual

Using Security Profile by Device

Security Profile by Device is used to enable or disable user access to the following devices:

IDE controller

When this feature is set to Disable, all devices connected to the

 

IDE controller (such as hard disk drives or the CD-ROM drive)

 

are disabled and will not be displayed in the system

 

configuration.

Diskette Drive Access

When this feature is set to Disable, the diskette drive cannot be

 

accessed.

Diskette Write Protect

When this feature is set to Enable, all diskettes are treated as if

 

they are write-protected.

To set Security Profile by Device, do the following:

1.Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19).

2.From the IBM Setup Utility program menu, select Security.

3.Select Security Profile by Device.

4.Select the desired devices and settings and press Enter.

5.Return to the IBM Setup Utility program menu and select Exit and then Save Settings or Save and exit the Setup Utility.

Note: If you do not want to save the settings, select Exit the Setup Utility without saving.

Using IDE Drives Setup

In addition to listing the different IDE devices, there are options for configuring the serial and parallel IDE controllers.

Parallel ATA

This setting allows the user to disable one or both of the parallel

 

IDE controllers.

Serial ATA

This setting allows the user to disable the serial ATA controllers.

Native Mode Operation This setting is only available when the serial ATA controller is enabled. This allows the user to specify whether the parallel and serial ATA controllers will operate in legacyor nativemode. By default, they will operate in native mode unless both parallel ATA controllers are populated and a serial ATA drive is present. Then the serial ATA drive will become nativemode. The user can select Automatic or the serial ATA controller to run in nativemode. However, running in nativemode might not work with older operating systems.

To configure IDE Drives Setup, do the following:

1.Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19).

2.From the IBM Setup Utility program menu, select Devices.

3.Select IDE Drives Setup.

4.Select the desired devices and settings and press Enter.

5.Return to the IBM Setup Utility program menu and select Exit and then Save Settings.

Chapter 5. Using the IBM Setup Utility 21

Selecting a startup device

If the computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device.

Selecting a temporary startup device

Use this procedure to startup from any boot device.

Note: Not all CDs, hard disks, and diskettes are startable (bootable).

1.Turn off the computer.

2.Press and hold the Enter key and turn on the computer. Release the Enter key when the logo appears.

3.The Access IBM Predesktop Area opens.

4.Click Startup and follow the instructions on the screen.

Note: Selecting a startup device from this list does not permanently change the startup sequence.

Changing the startup device sequence

To view or permanently change the configured startup device sequence, do the following:

1.Start the IBM Setup Utility program (see “Starting the IBM Setup Utility program” on page 19).

2.Select Startup.

3.Select Startup Sequence. See the information displayed on the right side of the screen.

4.Select the devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error Startup Sequence.

5.Select Exit from the IBM Setup Utility menu and then Save Settings or Save and exit the Setup Utility.

If you have changed these settings and want to return to the default settings, select

Load Default Settings on the Exit menu.

Advanced settings

On some computer models the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This feature works only with HyperThreading-aware operating systems such as Microsoft Windows XP. The default setting for HyperThreading is Enabled. However, if you select Set Defaults and are using an operating system other than Windows XP, the computer performance might be degraded. Therefore, you should always set HyperThreading to Disabled unless you are sure your operating system supports HyperThreading.

22 Hardware Maintenance Manual

Chapter 6. Replacing FRUs

FRU replacements are to be done by trained service technicians only.

Important: Before you install or remove any FRU, read “Safety information” on page 153. These precautions and guidelines will help you work safely.

Locating controls and connectors on the front of the computer

This section shows the various external connectors on the computer to which you can attach external devices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Cover keylock (some models)

6

USB connectors (2)

2

Optical drive

7

Microphone connector (line in)

3

Hard disk drive activity indicator

8

Headphone connector (line out)

4

Power-on indicator

9

Diskette drive

5

Power button

 

 

 

 

 

© Copyright IBM Corp. 2005

23

Locating connectors on the rear of the computer

The following illustration shows locations of connectors on the rear of the computer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Power cord connector

8

 

VGA monitor connector

2

Cable lock latch

9

 

Parallel connector

3

Rope clip (U-bolt) holes

10

Audio line-in connector

4

PCI adapter slots

11

Audio line-out connector

5

Serial connectors (2)

12

USB connectors (4)

6

Ethernet connector

13

PS/2 keyboard connector

7

USB connectors (2)

14

PS/2 mouse connector

Note: Some connectors on the rear of the computer are color-coded to help determine where to connect the cables.

vMouse - green

vKeyboard - purple

vMonitor - dark blue

vMicrophone - pink

vAudio line-out - lime green

24 Hardware Maintenance Manual

Loading...
+ 166 hidden pages