Hyundai HQP421HR, HQP501HR, HQP421SR User Manual

4 (1)
Hyundai HQP421HR, HQP501HR, HQP421SR User Manual

USA

Hyundai ImageQuest America

3101 North First Street San Jose, CA 95134 Hyundai tech support

Tel : +800-568-0061,408-232-8654 Fax : +408- 232-8146

e-mail : syuen@hyundaiqa.com

AVC USA. INC.

777 Mark Street, Wood Dale, IL 60191 Tel : 630-595-0123 / 800-568-0060 Fax : 630-595-2345 / 800-784-9422 e-mail : avctech@avcusa.com

NEW ZEALAND

TRANSTECH DISTRIBUTORS Ltd.

PO Box 12985 Penrose,

Auckland New Zealand Tel : 09-571-0775

Fax : 09-571-0776

e-mail : LouisG@Transtech.co.nz WWW : www.transtech.co.nz

AUSTRALIA

Thomas Electronics Australia Pty Ltd.

3 Sheridan Close

Milperra NSW 2214, Australia

Tel : +61 2 9773 7400

Fax : 61 2 9773 7177

Attn : Ms. Shiely Poniman

GERMANY

Hyundai ImageQuest Europe GmbH

Geheimrat Hummel Platz 2

65239, Hochheim, Germany Tel : 06146 / 904 444

Fax : 06146 / 904 410

e-mail : service@hyundaiq.de WWW : www.hyundaiq.com

JAPAN

Hyundai ImageQuest JAPAN

Shin-Hibiya Bldg, East 5F 1-3-6 Uchisaiwai-Cho, Chiyoda-ku, Tokyo, Japan 100-0011

Tel : 03-5157-2286

Fax : 03-5157-2284 e-mail : pjkim@iqt.co.kr C/S P.J.Kim

Hyundai

Plasma Display

HQP421SR/421HR/501HR

User’s Guide

P/N 632 0238 201 Rev.03

* The above image may look different from the real product.

 

 

FCC Information

User Instructions

The Federal Communications Commission Radio Frequency Interference Statement includes the following warning :

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for assistance.

User Information

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Connecting of peripherals requires the use of grounded shielded signal cables.

HYUNDAI Plasma Display

 

DECLARATION OF CONFORMITY

 

 

WE

HYUNDAI ImageQuest CO., LTD.

 

Ami-ri Bubal-Eub Ichon-Si Kyungki-Do

 

467-860 KOREA

declare under our sole responsibility that the product:

Kind of equipment : PDP TV

Type-Designation : PT42AS000 / PT42AH000 / HQP50AH000

to which this declaration relates is in conformity with the following standard(s) or other normative document(s)

Safety

: EN60065 : 1998 / IEC60065 : 1998

 

EMC

: EN 55013 / 1990+A12 : 1994+A13 : 1996+A14 : 1999

 

EN 55022 : 1998+A1 : 2000 Class B

 

 

EN 55024

: 1998+A1 : 2001

 

 

EN 55020

: 1994+A11 : 1996+A13 : 1996+A14 : 1999+A12 : 1999

 

EN 61000-3-2 : 2000, EN 61000-3-3

: 1995+A1 : 2001

 

 

 

 

following the provisions of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC.

Accredited testlaboratory: TÜV Rheinland Am Grauen Stein

51105 Köln

KOREA /MAY. 15, 2004

HONG KI, KIM

Place and date of issue)

(Name and signature of

 

authorized person)

Important Tips

Image Retention effect(Image Sticking)

1.

Cause :

- Image Retention Effect could be come from displaying a still picture in certain period of time with at

a certain area continuously, as the feature of Plasma Display Panel.

- This is the same matters to other companies' PDP products, too.

2.

Preventation :

-To avoid this matter, use the product after reducing brightness and contrast, especially a still image is displaying for a long time. (Example : Contrast 50, Brightness 50 - See the page 36)

Once Image retention occurs, change the mode into Video mode which displays more motion pictures. It will help reduce this matter, but cannot completely eliminate once it occurs.

It makes the screen’s brightness worse as displaying a fixed pattern often. - Use the fuction, Pixel Shift in still image, in our PDP products.

(For more details, see the below page 73)

3.

Solution :

- The temporary image sticking would decrease with displaying Full-White pattern after 10 hours.

- The permanent image sticking couldn’t take off under the latest technology even though being in its

manufacturer.

4.

Notice :

-It is very important to notify every buyer/customer this information and All Branches/Buyers /Customers should be fully aware of this.

-Image Sticking in PDP products couldn’t get the support from a manufacturer, and does not come under the warranty.

Second Tip

• Pixel Defect :

Plasma Display Panel(PDP) is made of a group of refined pixels (cells). The Panel, in which 99.9% of pixels have approved, is a normal product. Therefore, only a few of abnormal pixels may appear, however, this has no influence upon PDP performance.

HYUNDAI Plasma Display

Image Sticking Precaution

Still Image/Panorama/Wide/4:3 in motion Image

Panorama, Wide, 4:3 aspect ratio

Box or Still image

• Precaution :

-Image Sticking could be come from Still Image and Boundary line for a long time display and Brightness gap in Boundary.

-This Matter(Image Sticking) is same thing under the other PDP's Company.

-Still Image/Letter in watching TV also will be effect to Image sticking. *This matter(Image Sticking) is out of warranty.

Features

A Wide Array of Screen Settings

You can choose different screen settings depending on the type of program you are watching or the surrounding conditions (the lighting or the outside weather conditions).

You can switch among Standard, Dynamic, Movie and Mild options or you can configure the screen settings for yourself.

A Wide Array of Sound Settings

You can choose an optimal sound setting for the type of program you are watching.

You can switch among Music, Movie, News and Standard options or you can configure the settings for yourself.

SRS WOW(Surround) Audio Function

You can listen to dynamic and surround sound only with ordinary speakers.

WSS(Wide-Screen-Signaling) Function

This function is designed to detect signal transmission information and automatically convert it to the appropriate signaling for broadcast format.

Watching TV on Scart

You can change channels while watching TV through F-Scart .

Teletext Function

This function is designed to detect broadcasting signals that contain TTX information to display it.

Two Tuner Built-In

You can watch two channels at the same time and changing each channel.

PIP Viewing

You can watch TV or TTX information at the same time while working on PC or watching VCR/DVD movies.

Various of the Aspect Ratio

You can adjust aspect Ratio as you want.

Auto On/Off Function

This fuction allows you to turn On/Off your PDP TV at the preset Time.

If there is no signal during a specific time period, power will be off.

Auto Detection Sound Format

When watching TV in Nicam/A2 Stereo mode, this function automatically detects transmission signaling to display broadcasting status on the OSD.

Table of Contents

General Information

 

Safety Precaution ................................................................

5

Contents of the Package ....................................................

11

Separately Sold Products ..................................................

11

Parts Names and Functions .............................................

13

Remote Control ..................................................................

15

How To Use Speakers (Standing Type) ...............................

17

How To Use Speakers (Desk Type) .....................................

18

How To Install Wall Hanger Support ...................................

19

How To Install Wall mount frame .......................................

20

How To Install Desktop Stand ............................................

21

Connections

 

Connecting Indoor/Outdoor TV Antenna (UHF/VHF) .............

23

Connecting to the antenna input connection

 

on the external equipment .................................................

24

Before connecting the video/audio connections to

 

external devices ................................................................

25

Connecting VCR, Cable/Satellite Receiver ..........................

26

Connecting a DVD player ...................................................

27

Connecting DTV(Digital Broadcast) Receiver .......................

28

Playing back a tape recorded on a camcorder ....................

29

Connecting to a PC(DVI, D-SUB) .........................................

30

Resolutions Supported in PC ..............................................

31

Scart Connection to the External Input/Output ....................

32

Scart Pin Specifications .....................................................

33

Picture Setup

 

How to Select the Picture Mode .........................................

35

How to Set the Desired Picture ..........................................

36

How to Set Blue Screen .....................................................

37

How to Set Film Mode ........................................................

38

How to Select a Color Temperature ....................................

39

How to Set PIP [Mode] .......................................................

40

How to Set Multi-Screen [Input Source/Position/Size] ........

41

Supported PIP Table ...........................................................

43

How to Set Noise Reduction ...............................................

44

How to Select the Fit(Fine Image Technology) Engine Mode ...

45

Sound Setup

 

How to Select the Audio Mode ...........................................

47

How to Set the Desired Audio ............................................

48

How to Select AVL .............................................................

49

HYUNDAI Plasma Display

How to Select SRS WOW(Surround) ..................................

50

How to Select S.Mode ........................................................

51

How to Set the Output of Subwoofer ..................................

53

Channel Setup

 

Storing channel Automatically ............................................

55

Storing channel Manually ..................................................

56

Assigning Names to Channel .............................................

58

Skipping Unwanted Channels ...........................................

59

Sorting the Stored Channels ..............................................

60

Activating the Child Lock ...................................................

61

Fine Tuning Channel Reception ..........................................

62

Using the LNA(Low-Noise-Amplifier) Feature .....................

63

Teletext Feature .................................................................

64

Displaying the Teletext Information ....................................

65

Selecting Display Options ..................................................

65

Function Setup

 

How to Select the Aspect Ratio ..........................................

69

Displaying Information .......................................................

71

How to Set Key-Lock .........................................................

72

Using the Pixel Shift / Full White / Wiper Function ..............

73

How to Freeze Picture.........................................................

74

How to set DPMS ...............................................................

75

Choosing the Your Language .............................................

76

How to Set Image Adjust in PC Mode .................................

77

Using the Auto Change ......................................................

79

Using the Auto Size ............................................................

80

Display Mode According to Signal Source for Auto Size Settings ..

81

Clock Setup

 

How to Set Clock ...............................................................

83

How to Set On Time ...........................................................

84

How to Set Off Time ...........................................................

86

How to Set Sleep Time .....................................................

88

Appendix

 

Glossary ............................................................................

91

Troubleshooting .................................................................

93

Care and Cleaning .............................................................

95

Product Specifications .......................................................

96

Component Video Signal Format ........................................

97

GENERAL INFORMATION

Safety Precaution

The contents of this section are provided for the safety of users and their property.

Please read the instructions carefully before using.

WARNING

If there is a persistent accumulation of dusts or water on the plug, please make sure to wipe it off using a dry cloth.

- It may cause a fire or an electric shock.

Do not connect multiple electrical appliances to a single outlet.

-It may cause a fire due to overheating from the outlet.

WARNING

Do not put a water bowl, filled with liquids such as vases, candle, bug repellant smoke, cigarette, plants, or heavy thing on the PDP.

- It may cause electric shock or fire and also heavy things may cause injury when they fall.

Do not install in a place where there is oil, smoke, excessive humidity, or where water may be sprinkled, dripped, splashed on it.

- This may cause electric shock or fire.

5

HYUNDAI Plasma Display

Safety instructions are divided into “Warning” and “Alert”. Their meanings are as follows.

This icon is intended to alert the user to the presence of potential danger and important operating instructions.

WARNING : When there is a possibility of serious injury or death if not observed.

ALERT : When there is a possibility of slight injury or product damage if not observed.

Do not use a damaged power cord or plug, or loose outlet.

- They may cause electric shock or fire.

Firmly plug in the power cord so that

Never touch the

it does not pull out.

outlet with wet hands.

- An unstable connection may cause fire.

- This may cause electric shock.

Do not use or store a flammable spray or inflammable things near the PDP.

- They may cause explosion or fire.

 

Do not install the PDP in a

Do not install on an unstable place

bookshelf, closet, or a place where

or small support.

there is poor air circulation.

- This may cause the PDP to fall, resulting in

- Fire may be caused due to the rise of internal

serious injury to a child or adult.

temperature.

INFORMATION GENERAL

6

GENERAL INFORMATION

Safety Precaution ......................................

Continued from previous page

The contents of this section are provided for the safety of users and their property.

Please read the instructions carefully before using.

WARNING

Never attempt to open, fix, or modify the PDP.

- When there is a need for fixing, call a service center. Fire or electric shock may be caused.

Make the antenna cable loop at the entrance of the building Any necessary action such as making the antenna cable loop at the entrance of the building should be taken to prevent rainwater on the outdoor antenna cable from possibly running into the indoor.

- If raindrop gets into the PDP, it may cause a fire or an electric shock.

WARNING

Do not block ventilating slits.

- Blocking the ventilation slits prevents inner heat from escaping, which may lead to a fire.

Any heat sources such as radiators and heat registers, etc. on or near the PDP.

- It may cause a fire.

7

HYUNDAI Plasma Display

Safety instructions are divided into “Warning” and “Alert”. Their meanings are as follows.

This icon is intended to alert the user to the presence of potential danger and important operating instructions.

WARNING : When there is a possibility of serious injury or death if not observed.

ALERT : When there is a possibility of slight injury or product damage if not observed.

When the PDP produces abnormal noise, burning smell, or smoke, unplug the PDP immediately and call a service center.

Do not put a metallic object like chopstick, wire, or puncher or inflammables like paper or a match in a vent, headphone jack, or AV jacks of the PDP.

- Electric shock or fire may be caused.

Do not install the product on the floor.

- If it falls over, your child may be injured.

- Electric shock or fire may be caused.

Unplug the product during lightning or thunderstorms and never touch the antenna cable.

- It may cause a fire or an electric shock.

When moving the PDP assembled with speakers, make sure to detach the speakers from it.

-If you carry the product holding the speakers, it may cause the product to fall, causing serious injury or damage.

Keep the remote control batteries out of sight and out reach of children.

-If your child swallows a battery, see your doctor immediately.

INFORMATION GENERAL

8

GENERAL INFORMATION

Safety Precaution ......................................

Continued from previous page

The contents of this section are provided for the safety of users and their property.

Please read the instructions carefully before using.

WARNING

Do not allow children to climb or play on the PDP.

- If it falls over on children, it may cause serious injury.

Do not place toys and cookies, etc. on the PDP, which may attract children’s attention. Children will climb on the PDP to reach whatever they have their eyes on.

-If it falls over on children, it may cause serious injury.

ALERT

In the event of damaging or dropping the product, switch off the power and remove the plug.

- Using a damaged product may cause an electric shock or a fire.

- Contact your local service center.

Please avoid touching the panel at the rear of PDP as it is producing high temperature.

-Direct contact with the hot surface may cause physical burns.

9

HYUNDAI Plasma Display

Safety instructions are divided into “Warning” and “Alert”. Their meanings are as follows.

This icon is intended to alert the user to the presence of potential danger and important operating instructions.

WARNING : When there is a possibility of serious injury or death if not observed.

ALERT : When there is a possibility of slight injury or product damage if not observed.

Alcohol

Benzene

LUBRICANT

When replacing batteries, make sure to match the batteries to the

(+) and (-) marks in the battery compartment.

-Mismatching of polarities may result in internal damage to batteries, fire due to leakage or contamination.

When cleaning the PDP, make sure to disconnect the power plug and use a dry, soft cloth for a cleanup.

-Please avoid using chemicals such as wax, benzene, alcohol, thinner, mosquito spray, air freshener, lubricant or synthetic detergent.

Always use the standard batteries and avoid using old batteries together with new ones.

-Otherwise it may result in internal damage to batteries, fire due to leakage or contamination.

INFORMATION GENERAL

Unplug when you do not use your PDP for a long time.

-If dust is stacked on the PDP, electric shock or fire may be caused from heat, fire, or deterioration of insulation.

When moving the PDP, 2 or more people are advised to carry it.

- Injury or damage may be caused when the PDP falls.

Consult a service center or customer service for inside cleaning about once a year.

- When dust is piled inside the PDP for long time, fire or malfunction may be caused.

10

GENERAL INFORMATION

Contents of the Package

To purchase additional parts, consult a distributor or selling agent.

 

 

3

 

2

6

1

5

9

 

4

8

 

7

0

UK Japan

Power Cord

America/Canada Europe

Remote Control/2 Batteries

(1.5V AAA)

South Africa

Australia

User’s Guide

Antenna Cable

Korea

Separately Sold Products

If you want to purchase separately sold products, consult a service center, electronics shops, or parts seller.

Desk type speaker stand

Desk type stand

Desk type speaker

11

HYUNDAI Plasma Display

INFORMATION GENERAL

Wall mounting frame

Adjustable wall mounting frame

Ceil mounting frame

DVI PC video(digital) cable

Component(Y, Pb, Pr) cable

Composite(Video & Audio) cable

S-video cable

PC signal cable

Scart cable

12

GENERAL INFORMATION

Parts Names and Functions

Front View

* The above image may look different from the real product.

Power button

Use this button to turn on or off the PDP.

Volume buttons

Use these buttons for your desired sound level. These buttons also serve as the cursor of Select/Adjust when in Menu mode.

Channel buttons

Use these buttons to change channels. These buttons also serve as the cursor of Down and Up buttons when in Menu mode.

Source button

Use this button to switch among inputs connected to the PDP.

Menu button

Use this button to display or exit from menus.

Remote sensor and power LED. Point the remote control toward here. It displays standby or operation status.

13

HYUNDAI Plasma Display

Rear View

Sub woofer output

If you wish to reproduce the lower bass frequencies, please connect the cable to your Subwoofer speaker with *AMP.

RS-232 input terminal Connect to the RS-232 terminal of a PC for the service check.

*For the control method using this terminal, consult an authorized PDP monitor dealer.

Phone Jack

Extend an RS-232 input. DVI input terminal

Connect to the DTV receiver with DVI terminal or to external devices such as a PC.

PC/DVI Audio input terminal

INFORMATION GENERAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect to the audio output

output terminal of DTV

program.

terminal of a PC.

receiver.

H SCART input terminal

D-SUB input terminal

S-video input terminal

For Composite Video input

Connect to the DTV

Use this for the better video

and audio inputs used in

Receiver with D-Sub

quality than video input

the European area.

terminal or to RGB output

terminal.

F SCART input terminal

terminal of a PC.

Video Composite input

For Composite Video/Audio

Audio input terminal for

terminal for VCR

or R,G,B inputs used in the

DVD

Connect to the Composite

European area.

Connect to the audio output

Video output terminal of

ANT. input

terminal of DVD player.

VCR or DVD player.

This allows you to connect

Component input

Audio input terminal for

your antenna.

terminal for DVD or DTV

VCR

Power input terminal

Connect to the Component

Connect this when S-video

Power cord is connected

output terminal of DVD

or Composite Video inputs.

here.

player/DTV receiver.

Video output

Speaker terminal

Audio input terminal for

This allows you to view the

Stand assembly

DTV Component

current program from

Speaker assembly

Connect to the audio output

another external source at

Carrying handles

terminal of DTV receiver.

the same time.

Screw hole for fixing on a

Component input

Audio output

wall

terminal for DTV

This allows you to hear the

 

 

 

 

 

 

 

 

Connect to the Component

sound for the current

 

 

 

 

 

 

 

 

14

GENERAL INFORMATION

Remote Control

POWER/STANDBY

Use this button to turn the TV set on or off. MUTE

Use this button to turn the sound off completely. NUMERIC KEYS

Use these buttons to select channels. PREVIEW

Use this button to return to the previous channel. ASPECT RATIO

Use this button to quickly change the picture format. STILL

Use this button to freeze a picture. VOLUME

Use this button to control the volume level CHANNEL

Use these buttons to select channels. You can also use these buttons when changing pages in TTX mode.

SWAP

Use this button to switch what is being shown on the main picture to the sub-picture.

SIZE

Use this button to change the size of a sub-picture. SUB-PICTURE CHANNEL SELECTION

Use these buttons to select or adjust each item of menu. Or you can select channels in sub-pictures.

TV/AV buttons

Use this button to display the available video sources. (TV, Video, S-Video, DTV, DVD, PC, DVI, H Scart, F Scart)

PC AUTO

Use this button to automatically adjust settings according to the frequency and resolution selection in PC mode.

INFOMATION

Use this button to display picture mode, resolution or various program information.

WIPER

Use this button to prevent any possible ghosts. White bar will pass through the TV screen to prevent ghosts.

EXIT

Use this button to exit from a menu. SELECT/ADJUST

Select or adjust each item of menu. MENU

Use this button to adjust screen, audio, channel, function, time, etc.

SOURCE [MULTI SCREEN]

Use this button to select input signals for sub-pictures. PIP (PICTURE IN PICTURE) ON/OFF

Use this button to watch more than one picture at once. SLEEP

Use this button to allow your TV to turn off automatically at designated time.

POWER

MUTE

 

1

 

2

3

4

 

5

6

7

 

8

9

 

 

PREVIEW

 

 

0

 

SOUND

PICTURE

ASPECT

STILL

S.MODE

 

 

 

SLEEP

VOLUME

CHANNEL

ON/OFF

SOURCE

SIZE

SWAP

PIP

 

 

 

 

MENU

 

EXIT

 

 

TV/AV

INFO

WIPER

PC AUTO

TTX ON/OFF

TTX/MIX

INDEX

LIST/FLOF

STORE

HOLD

SIZE

REVEAL

SUB PAGE

15

S.MODE

Use this button to display types of audio signals currently aired on TV. Or you can use this button to switch to other Sound Mode available.

SOUND

Use this button to select the status of sound. PICTURE

Use this button to select the status of picture. DIGIT KEY

Use this button to select your desired channel using numeric keys.

MENU

INFO

WIPER

PC AUTO

TTX ON/OFF

TTX/MIX

INDEX

LIST/FLOF

STORE

HOLD

SIZE

REVEAL

SUB PAGE

HYUNDAI Plasma Display

Teletext & Fastext Function

TTX ON/OFF

Use this button to activate the teletext mode. LIST/FLOF

To select LIST or FLOF STORE

To store a page(s) in LIST mode. SUB PAGE

To move to Sub Page. REVEAL

To reveal the hidden TTX information BLUE

To move between BLOCK and BLOCK. YELLOW

To move to NEXT GROUP PAGE. GREEN

To move to NEXT EXISTING PAGE. RED

To return to the previous selection SIZE

The size is changed from Normal, Double to Double Bottom mode in order.

HOLD

To freeze the TV screen when in Muli Page TTX/MIX

To select TTX or MIX mode INDEX

To move to INDEX in FLOF or move to INFO in TOP.

How to Insert Batteries in Remote Control

1

2

3

Press and hold part and push

Insert batteries with proper

Use the remote control with cover

to open cover.

polarities of + and - .

closed.

*Battery type : 1.5V/UM-3(AA/R06)

INFORMATION GENERAL

16

GENERAL INFORMATION

How To Use Speakers (Standing Type)

Parts configuration chart

2 Speakers (left and right)

4 brackets

16 fixing screws

2 sets of speaker cables

 

 

 

(left and right)

Connect speaker cables between terminals on the rear of speakers with speaker connection terminals on the rear of PDP. (Connect cables and terminals in the same color)

WARNING

Do not move the product holding the speakers. Always use handles on the PDP.

(Brackets connecting PDP and speakers may be damaged.)

17

HYUNDAI Plasma Display

How To Use Speakers (Desk Type)

Parts configuration chart

INFORMATION GENERAL

2 Speakers (left and right)

2 Speaker-stands

8 fixing screws

2 sets of speaker cables

 

(left and right)

 

(left and right)

Assembly and Connect method

Insert speaker-stands in the grove

Upright

and place them on

on the bottom of speakers and

desired place left and right of PDP.

fasten them sing fixing screws.

(Left and right side each)

(Left and right side each)

 

 

 

 

 

Connect speaker cables between terminals on the rear of speakers and speaker connection terminals on the rear of PDP. (Connect cables and terminals in the same color)

18

GENERAL INFORMATION

How To Install Wall Hanger Support

1. Caution

2. Parts configuration chart

1. Install on the vertical wall surface only.

2.Do not install on the following places to protect the performance of PDP and to prevent malfunction.

Near sprinkler Detector

Near heating devices

Places where vibration or shock may be applied

Near high voltage electric power line

3.Install in a proper method with the structural materials of the wall. If the wall is not strong enough to stand weight of PDP set, reinforce the wall surface before installation.

4. Do not install within a wall.

Wall mount frame

 

 

 

4 screws

Spring washer

4 plastics for

 

 

mount frame

3. Angle Adjustment(Option)

The angle of PDP may be adjusted from 0 degree to 20 degree in 5 steps with 5 degrees. Use the angle adjustable hole on the side of fixing panel when adjustment is needed. (This function is supported with angle adjustable type wall mount frame only.)

50 angle

100 /00 angle

150 angle

200 angle

50 angle

150 angle

No angle

Angle adjustable hole

* Fixed type wall mount frame does not support angle adjustable function.

19

HYUNDAI Plasma Display

How To Install Wall mount frame

4. Installation Method

1. Unscrew screws fasted on four spots on the back of PDP.

3. Fix the wall mount frame on the wall with screws or nails.

2. Fasten the screws and plastics for mount frame on the spot where screws were as shown on the picture.

4. Hang the plastics for the mount frame on the wall mount frame. (If the PDP is lifted too much, the hanging plastic may be separated.)

INFORMATION GENERAL

20

How To Install Desktop Stand

INFORMATION

2.

Align the stand with PDP body below and fasten the stand bars using 4 fixing screws.

 

1.

Place the PDP body on a flat desk or shelf. Clean the surface of the desk or shelf in order to prevent scratch on the

GENERAL

 

product.

3.

After the assembly is over, stand the assembled product at a desired place.

 

Fixing screws

Warning : Do not install at an unstable place or on a small support.

(When a child plays around the product and touch it, PDP may fall and injure the child.)

21

Connections

H Y U N DA I P L A S M A D I S P L AY

CONNECTIONS

Connecting Indoor/Outdoor TV Antenna(UHF/VHF)

Connection Method

Ensure to connect an antenna cable to the antenna input connection.

316(&$/&7+&!1*($&"*

316(&$/&7+&!1*($10

,-.'$!/-)*

'"..$!/-)*

-0*$10

 

 

 

23,'4",'5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-0*$10

23,'4",'4/-#.(5

Antenna cable

Coaxial cable

-0*$10

23,'4",'4/-#.(5

Antenna cable

Coaxial cable

How to Watch

1

Turn on your PDP and press TV/AV on remote control unit.

2

Press

to move between entries. And press

to select TV.

3

Press

CHANNEL to select the desired channels.

 

indoor antenna

outdoor antenna

CURRENT : TV

 

T V

N O C A B L E

V I D E O

S - V I D E O

N O C A B L E

F S C A R T

 

H S C A R T

N O C A B L E

DVD

DTV

N O C A B L E

PC

N O C A B L E

DVI

N O C A B L E

 

 

When inserting a 75-ohm coaxial cable into the input connection, ensure the wire tip not to bend.

If you experience poor signal reception, we recommend you purchase a signal amplifier for better picture quality.

23

HYUNDAI Plasma Display

Connecting to the Antenna Input Connection on the External Equipment

Connection Method

1

Connect an antenna cable to VCR/Cable/Satellite Receiver with the

antenna input.

 

2

Use a coaxial cable to connect VCR/Cable/Satellite Receiver's antenna output to the antenna input on your

 

PDP.

 

 

 

 

 

 

 

 

 

 

 

 

 

316(&$/&7+&!1*($&"*

 

 

 

.

)

8

+9

+:

 

 

 

 

636$/&7+&0(0*2;<=>4;<=?4@A=?4B=<=>5

316(&$/&7+&!1*($10

 

 

 

 

 

 

 

 

,-.'$!/-)*

'"..$!/-)*

-0*$10

 

VCR/Cable Receiver

 

 

23,'4",'5

 

 

 

 

 

 

 

.

)

8

+9

+:

 

 

 

-0*$10

-0*$&"*

2.5

2)5

316(& !C316(&

-"61&

-0*$10

23,'4",'4/-#.(5

Coaxial cable

CONNECTIONS

24

CONNECTIONS

Before connecting the video/audio connections to external devices .....

Please make sure to read the following information on connection to enjoy best picture quality.

Video/Audio connectors

Types of video/audio cable :

DVI-D 15-Pin D-Sub COMPONENT S-VIDEO COMPOSITE FULL SCART HALF SCART

Best picture quality is displayed in the following order.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVI-D, D-Sub

 

> COMPONENT

>

S-VIDEO

> COMPOSITE

 

FULL SCART

 

 

 

 

 

 

 

 

 

 

 

 

 

HALF SCART

The superior picture quality starts from the far left side.

Full Scart supports Composite simultaneously

25

HYUNDAI Plasma Display

Connecting a VCR, Cable/Satellite Receiver

Connection Method

1

Connect Video/S-Video cable between Video/S-Video output terminal of VCR or Cable/Satellite receiver and

Video/S-Video input terminal of PDP.

 

 

 

 

(Connect cables and terminal in the same colors)

 

 

2

Connect Audio cable (left:white color, right:red color) between Audio output terminal of VCR or cable/satellite

 

receiver and Audio input terminal of PDP.

 

 

 

 

(Connect cables and terminal in the same colors)

 

 

 

 

 

 

 

 

316(&$/&7+&!1*($&"*

 

 

 

.

)

8

+9

+:

 

 

 

 

636$/&7+&0(0*2;<=>4;<=?4@A=?4B=<=>5

316(&$/&7+&!1*($10

 

 

 

 

 

 

 

 

,-.'$!/-)*

'"..$!/-)*

-0*$10

 

VCR/Cable Receiver

 

 

23,'4",'4/-#.(5

 

+9

+:

 

 

 

 

.

)

8

 

 

 

-0*$10

-0*$&"*

2.5

2)5

316(& !C316(&

-"61&

POWER Cable

AUDIO Cable

S-VIDEO Cable

or

 

VIDEO Cable

CONNECTIONS

How to Watch

1

Turn on your PDP and press TV/AV on remote control unit.

2

Press

to move between entries. And press

to select

 

Video or S-Video.

 

Use S-video cables for better picture quality.

CURRENT : S - VEDIO

T V

C O N N E C T

V I D E O

S - V I D E O

C O N N E C T

F S C A R T

 

H S C A R T

N O C A B L E

DVD

DTV

N O C A B L E

PC

N O C A B L E

DVI

N O C A B L E

26

CONNECTIONS

Connecting a DVD Player

Connection Method

Connect video cables(Y, Pb, Pr) between output terminals(Y, Pb, Pr) of DVD player and the input 1 terminals(Y, Pb, Pr) of DVD(480i/480p/720p/1080i) on the rear of PDP.

(Connect cables and terminal in the same colors)

2

Connect Audio cable between Audio output terminal of DVD player and Audio input terminal for DVD Audio on

the rear of PDP.

 

 

 

 

 

 

 

(Connect cables and terminal in the same colors)

 

 

 

 

 

 

 

 

 

 

316(&$/&7+&!1*($&"*

 

 

DVD Player

 

 

 

 

 

 

 

.

)

8

+9

+:

 

 

 

636$/&7+&0(0*2;<=>4;<=?4@A=?4B=<=>5

316(&$/&7+&!1*($10

 

 

!"#$%&'()

 

 

 

 

,-.'$!/-)*

'

 

&"*+"*

 

 

 

 

 

 

 

.

)

8

+9

+:

 

 

!C316(& /&7+&0(0*$316(& 316(& -"61&

AUDIO Cable

VIDEO(Y, Pb, Pr) Cable

How to Watch

1

Turn on your PDP and press TV/AV on remote control unit.

2

Press

to move between entries. And press

to select

CURRENT : DVD

 

T V

N O C A B L E

V I D E O

S - V I D E O

N O C A B L E

F S C A R T

 

H S C A R T

C O N N E C T

DVD

DTV

N O C A B L E

PC

N O C A B L E

 

 

Output terminal mark(Y, Pb, and Pr) of DVD player may be written as Y, B-Y, R-Y/Y-Cb-Cr / Y-Pb-Pr. (It depends on DVD player)

27

Loading...
+ 72 hidden pages