HTC XV6800 User Manual
Size:
4.27 Mb
Download

Appendix

A.1 Specifications

A.2 Regulatory Notices

A.3 Additional Safety Information

136 Appendix

A.1 Specifications

System Information

 

Processor

QUALCOMM® MSM7500, 384 MHz

Memory

- ROM : 256 MB embedded NAND Flash

 

- RAM : 64 MB SDRAM

 

(Figures are the total ROM and RAM memory available for use and storage. Since the memory is

 

shared by the Operating System, applications, and data, the actual available memory is less than what

 

is written).

Operating System

Windows Mobile® 6 Professional

 

 

Power

 

Battery

Rechargeable Lithium-ionpolymer battery, 1500 mAh

ChargingTime

Up to 4 hours

AC Adapter

Voltage range/frequency: 100 - 240V AC, 50/60 Hz

 

DC output: 5V and 1A

 

 

Display

 

LCDType

2.8”transmissiveTFT-LCDwith backlight LEDs,touch-sensitivescreen

Resolution

240 x 320 dot pixels with 64K colors

Alignment

Portrait and Landscape

 

Cellular Radio Module

Functionality

CDMA2000 1xEVDO/1xRTT and IS-95A/Bvoice or data

Mode

Dual-band(800 and 1900 MHz)

Internal Antenna

Yes

 

 

Physical

 

Dimensions

110 mm (L) x 59 mm (W) x 18.5 mm (T)

Weight

165g (with battery)

Camera Module

 

Type

2 Megapixel color CMOS camera with flash light

Resolution

Photo: 1600x1200 (UXGA), 1280x960 (SXGA), 640x480 (VGA), 320x240 (QVGA), 160x120 (QQVGA)

 

Video: 352x288 (CIF), 320x240 (QVGA), 176x144 (QCIF), 128x96

 

MMS Video: 176x144 (QCIF), 128x96

Digital Zoom

Up to 8x

 

 

Connections

 

Infrared

IrDA SIR

I/O Port

HTC ExtUSBTM : an11-pinmini-USBand audio jack in one

 

(ExtUSB is a proprietary connection interface that is trademarked by HTC).

Car Antenna

For connecting to an external phone antenna (850MHz and 1900MHz)

Connector

 

Wireless

Bluetooth®,Wi-Fi®

Connections

 

Appendix 137

Controls and Lights

Navigation Buttons 5-wayNavigation Control

Five program buttons : CAMERA, COMM MANAGER, MESSAGING, INTERNET EXPLORER MOBILE, VOICE COMMAND

Two phone functions :TALK and END

START MENU button

Two OK buttons

Two soft keys

Jog Wheel

POWER button

RESET button

WLAN switch

Hardware Keyboard QWERTY keyboard with two additional soft keys, and an ambient sensor that detects low light and automatically illuminates the keyboard.

LEDs

The left LED shows the following:

 

• A blinking Blue light for Bluetooth system notification of powered-upand ready to transmit radio

 

frequency signal.

 

• A blinking Green light for Wi-Fistatus.

 

• When both Bluetooth and Wi-Fiare enabled, their lights blink alternately.

 

The right LED shows Green and Amber lights for CDMA standby and network status, notification,

 

and battery charging status.

 

 

Audio

 

Audio Controller

AGC

Microphone/

Built-in/Dual,Hands-free

Speaker

 

Headphone

MP3/WAV/WMA/AAC/AAC+ codec

 

 

Expansion Slots

 

Memory Card Slot

microSDTM

138 Appendix

A.2 Regulatory Notices

Regulatory Agency Identifications

For regulatory identification purposes, your product is assigned a model number ofTITA100.

FCC ID: NM8TITA100. IC:4115A-TITA100.

To ensure continued reliable and safe operation of your device, use only the accessories listed below with yourTITA100.

The Battery Pack has been assigned a model number ofTRIN160.

This product is intended for use with a certified Class 2 Limited Power Source, rated 5 Volts DC, maximum 1 Amp power supply unit.

Federal Communications Commission Notice

DECLARATION OF CONFORMITY

UT Starcom hereby declares that this wireless device, TITA100, manufactured by HighTech Computer Corp., is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the original declaration of conformity can be found at the following Internet address:http://www.danger.com/consumers.php.

This wireless device, TITA100, manufactured by HighTech Computer Corp., complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party: HighTech Computer Corp.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio orTV reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected.

Consult the dealer or an experienced radio or television technician for help. Modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

FCC RF EXPOSURE INFORMATION

In August 1996, the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.The design of this device complies with the FCC guidelines and these international standards.

Appendix 139

BODY-WORNOPERATION

Your TITA100 PDA phone was tested for typicalbody-wornoperations with the back of the device kept 1.5 cm from the body. To comply with FCC RF exposure requirements, a minimum separation distance of

1.5 cm must be maintained between the user’s body and the back of the device, including the antenna.Thirdparty belt-clips,holsters and similar accessories containing metallic components should not be used. Bodyworn accessories that cannot maintain 1.5 cm separation distance between the user’s body and the back of the device, and have not been tested for typicalbody-wornoperations may not comply with FCC RF exposure limits and should be avoided.

When carrying the device on you, turning the display in towards the body will minimize RF exposure and maximize antenna efficiency.

Modifications

The FCC requires the user to be notified that any changes or modifications made to the device that are not expressly approved by HighTech Computer Corporation may void the user’s authority to operate the equipment.

FCC Hearing-AidCompatibility (HAC) Regulations forWireless Devices

On July 10, 2003, the U.S. Federal Communications Commission (FCC) Report and Order in WT Docket 01309 modified the exception of wireless phones under the Hearing Aid Compatibility Act of 1988 (HAC Act) to require digital wireless phones be compatible with hearing-aids.The intent of the HAC Act is to ensure reasonable access to telecommunications services for persons with hearing disabilities.

While some wireless phones are used near some hearing devices (hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference they generate.

The wireless telephone industry has developed a rating system for wireless phones, to assist hearing device users find phones that may be compatible with their hearing devices. Not all phones have been rated. Phones that are rated have the rating on their box or a label located on the box.

The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.

M-Ratings:Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices than phones that are not labeled. M4 is the better/higher of the two ratings.TITA100 is rated M3.

Hearing devices may also be rated. Your hearing device manufacturer or hearing health professional may help you find this rating. Higher ratings mean that the hearing device is relatively immune to interference noise.The hearing aid and wireless phone rating values are then added together. A sum of 5 is considered acceptable for normal use. A sum of 6 is considered for best use.

In the above example, if a hearing aid meets the M2 level rating and the wireless phone meets the M3 level rating, the sum of the two values equal M5. This should provide the hearing aid user with“normal usage” while using their hearing aid with the particular wireless phone.“Normal usage”in this context is defined as a signal quality that is acceptable for normal operation.

The M mark is intended to be synonymous with the U mark.TheT mark is intended to be synonymous with the UT mark.The M andT marks are recommended by the Alliance forTelecommunications Industries

140 Appendix

Solutions (ATIS).The U and UT marks are referenced in Section 20.19 of the FCC Rules.The HAC rating and measurement procedure are described in the American National Standards Institute (ANSI) C63.19 standard.

For information about hearing aids and digital wireless phones

FCC Hearing Aid Compatibility and Volume Control:

http://www.fcc.gov/cgb/dro/hearing.html

Gallaudet University, RERC:

http://tap.gallaudet.edu/DigWireless.KS/DigWireless.htm

SAR Information

SAR: 1.130W/kg @1g (USA)

THIS MODEL DEVICE MEETSTHE GOVERNMENT’S REQUIREMENTS FOR EXPOSURETO RADIO WAVES.

For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the HighTech Computer Corp. accessories supplied or designated for this product. Use of other accessories may not ensure compliance with the FCC RF exposure guidelines.

Your wireless mobile CDMA phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.The guidelines are based on the safety standards previously set by both U.S. and international standards bodies:

American National Standards Institute (ANSI) IEEE. C95.1-1992.

National Council on Radiation Protection and Measurement (NCRP). Report 86. 1986.

International Commission on Non-IonizingRadiation Protection (ICNIRP) 1996.

Ministry of Health (Canada), Safety Code 6.The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

The exposure standard for wireless mobile CDMA phone employs a unit of measurement known as the Specific Absorption Rate, orSAR.The SAR limit set by the FCC is 1.6W/kg*. Tests for SAR are conducted with

the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value.This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted

requirement for safe exposure.The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model.

The highest SAR value for this model device when tested for use at the ear is 1.130 W/Kg @ 1g and when worn on the body, as described in this user guide, is 0.922 W/Kg @ 1g. (Body-wornmeasurements differ among device models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement for safe exposure.

The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of https://gullfoss2.fcc.gov/prod/oet/cf/eas/ reports/GenericSearch.cfm after searching on FCC ID: NM8TITA100.

Additional information on Specific Absorption Rates (SAR) can be found on the CellularTelecommunications & Internet Association (CTIA) web-siteashttp://www.phonefacts.net.

Appendix 141

*In the United States and Canada, the SAR limit for mobile CDMA phone used by the public is 1.6 Watts/kg (W/kg) averaged over one gram of tissue.The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.

Normal condition only to ensure the radiative performance and safety of the interference. As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, it is recommended that no part of the human body be allowed to come too close to the antenna during operation of the equipment.

FCC Enhanced 911 (E911) Rules

BACKGROUND

The Federal Communications Commission (FCC) requires wireless carriers to transmit specific latitude and longitude location (Automatic Location Identification = ALI) information as well as“911”calls to Public Safety Answering Points (PSAPs) to identify the location of the caller in case of emergency.

Generally, the rules require that carriers identify an E911 caller’s location within 50 meters of the actual location for 67 percent of calls and within 150 meters of the actual location for 95 percent of calls.

TITA100’s ALI CAPABILITY

The TITA100 is anALI-capablePDA phone equipped with a GPS (Global Positioning System) receiver supporting asatellite-basedGPSALI-capablenetwork to comply with the FCC’s ALI requirements.

The network compliance with the above FCC requirements is dependent on: (a) the use of digital technology by the wireless network; (b) GPS satellite signals being able to reach the handset (such transmissions do not always work indoors, for example) ; and (c) handset signals reaching wireless“base stations”(atmospheric and environmental conditions may cause variations in handset receiving signal strength).

Also the transmission of the ALI information is subject, in part, to system constraints within the wireless network to which the E911 signal is transmitted and over which UT Starcom has no control.

Finally, customers are advised that the TITA100’s ALI capability is to be used for E911 purposes only.

For more information about placing emergency calls, see Chapter 3.

Compliance with Other FCC Regulations

OPERATING PROCEDURES

Never violate any of the following Rules and Regulations of the FCC when using your device. Such violations are punishable by fine, imprisonment or both.

Never use obscene, indecent, or profane language.

Never use your device to send false distress calls.

Never wiretap or otherwise intercept a phone call, unless you have first obtained the consent of the parties participating in the call.

Never make any anonymous calls to annoy, harass, or molest other people.

Never charge another account without authorization, to avoid payment for service.

Never willfully or maliciously interfere with any other radio communications.

Never refuse to yield the line when informed that it is needed for an Emergency Call. Also, never take over a line by stating falsely that it is needed for an emergency.

142 Appendix

IC Statement

Operation is subject to the following two conditions:

1.This device may not cause interference; and

2.This device must accept any interference, including interference that may cause undesired operation of the device.

Important Note

IC Radiation Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.

This Class B digital apparatus complies with Canadian ICES-003.

WEEE Notice

The Directive on Waste Electrical and Electronic Equipment (WEEE), which entered into force as European law on 13th February 2003, resulted in a major change in the treatment of electrical equipment at end-of-life.

The purpose of this Directive is, as a first priority, the prevention of WEEE, and in addition, to promote the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal.

The WEEE logo (shown at the left) on the product or on its box indicates that this product must not be disposed of or dumped with your other household waste.You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for recycling of such hazardous waste. Isolated collection and proper recovery of your electronic and electrical waste equipment at the time of disposal will allow us to help conserving natural resources. Moreover, proper recycling of the electronic and electrical waste equipment will ensure safety of human health and environment. For more information about electronic and electrical waste equipment disposal, recovery, and collection points, please contact your local city center, household waste disposal service, shop from where you purchased the equipment, or manufacturer of the equipment.

RoHS Compliance

This product is in compliance with Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003, on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) and its amendments.