specifications
8753ET/ES |
Network Analyzers |
HP 8753ET and 8753ES Network Analyzers 30 kHz to 3 or 6 GHz
This document describes the performance and features of the following products:
HP 8753ES S-parameter vector network analyzer
HP 8753ES Option 011 vector network analyzer without test set
HP 8753ET Transmission/reflection vector network analyzer
For more information about these analyzers, please see the following documents:
|
HP literature number |
HP 8753ET and 8753ES Network Analyzers Brochure |
5968-5159E |
HP 8753ET and 8753ES Network Analyzers Configuration Guide |
5968-5158E |
Table of contents
Definitions and test conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 System performance summaries . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Specifications and characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Measurement throughput summary . . . . . . . . . . . . . . . . . . . . . . . . .21 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Test set specifications for Option 011 . . . . . . . . . . . . . . . . . . . . . . . .22 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2
Definitions and test conditions
Specifications describe the instrument's warranted performance after a half-hour warm-up and over the temperature range of 25 ˚C ± 5 ˚C, unless otherwise stated. Specifications for frequencies above 3 GHz do not apply to instruments with Option 075 (75-ohm impedance).
Supplemental characteristics are typical but non-war- ranted performance parameters. These are denoted as “typical,” “nominal,” or “approximate.”
The measurement uncertainty curves and measurement port characteristics given for HP 8753ES systems also apply to the HP 8753ES with Options 006 and 011 and the HP 85047A test set (50-ohm), or the HP 8753ES Option 011 with an HP 85046B test set (75-ohm).
Dynamic range
System dynamic range is calculated as the difference between the receiver noise floor and the lesser of either the source maximum output or the receiver maximum input level. System dynamic range applies to transmission measurements only, since reflection measurements are limited by directivity.
Noise floor is specified as the mean of the noise trace over frequency. Noise floor is measured with the test ports terminated in loads, full two-port error correction for the HP 8753ES and enhanced-response error correction for the HP 8753ET (with 16 averages used during isolation), 10 Hz IF bandwidth (BW), maximum test port power, and no averaging during the measurement.
Measurement uncertainty
Measurement uncertainty curves utilize a Root Sum Square (RSS) model for the contribution of random errors such as noise, typical connector repeatabilities, and test set switching; this is combined with a worstcase model for the contributions of dynamic accuracy and residual systematic errors.
Curves show the worst-case magnitude and phase uncertainty for reflection and transmission measurements, after a full two-port error correction for the HP 8753ES and enhanced-response error correction for the HP 8753ET (including isolation with an averaging factor of 16) using the specified cal kit, with 10 Hz IF bandwidth (BW) and no averaging.
Measurement port characteristics
Characteristics show the residual system uncertainties for uncorrected performance and after accuracy enhancement using full two-port error correction for the HP 8753ES and enhanced-response error correction for the HP 8753ET. These characteristics apply for an environmental temperature of 25 ± 5 ˚C, with less than 1 ˚C deviation from the calibration temperature. HP 8753ET Option 004 may degrade transmission source match as much as 2 dB, resulting in up to 0.05 dB additional uncertainty in transmission tracking.
Corrected performance indicates residual error after calibration. It is determined by the quality of calibration standards, system repeatability, stability, and noise.
Uncorrected performance indicates intrinsic errors without calibration correction applied. This is related to the ultimate stability of a calibration.
3
System performance summaries
HP 8753ES (50-ohm systems)
7-mm test ports
Configuration |
|
Network analyzer |
HP 8753ES |
|
Standard and Option 006 |
Calibration kit |
HP 85031B |
Test-port cables |
HP 11857D |
System dynamic range |
|
30 kHz to 50 kHz |
70 dB1 |
50 kHz to 300 kHz |
90 dB1 |
300 kHz to 16 MHz |
100 dB |
16 MHz to 3 GHz |
110 dB |
Option 014 |
108 dB |
3 GHz to 6 GHz |
105 dB |
Option 014 |
103 dB |
Reflection uncertainty
Magnitude
Transmission uncertainty
Magnitude
1.Typical below 300 kHz.
2.Typical performance.
Measurement port characteristics
Frequency range
Corrected 30 kHz-300 kHz2 |
300 kHz-1.3 GHz |
1.3 GHz-3 GHz |
3 GHz- 6 GHz |
||
Directivity |
55 dB |
55 dB |
51 dB |
46 dB |
|
Source match |
55 dB |
51 dB |
49 dB |
43 dB |
|
Load match |
55 dB |
55 dB |
51 dB |
46 dB |
|
Reflection |
±(0.001 dB |
±(0.001 dB |
±(0.005 dB |
±(0.020 dB |
|
tracking |
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
|
Transmission |
±(0.008 dB |
±(0.006 dB |
±(0.009 dB |
±(0.021 dB |
|
tracking |
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
|
Uncorrected |
|
|
|
|
|
Directivity |
20 dB* |
35 dB |
30 dB |
25 dB |
|
Source match |
18 dB** |
16 dB |
16 dB |
14 dB |
|
Load match |
18 dB** |
18 dB |
16 dB |
14 dB |
|
Reflection |
±2.5 dB |
±1 dB |
±1 dB |
±1.5 dB |
|
tracking |
|
|
|
|
|
Transmission |
±2.5 dB |
±1 dB |
±1 dB |
±1.5 dB |
|
tracking |
|
|
|
|
|
Crosstalk |
90 dB*** |
100 dB |
100 dB |
90 dB |
|
*15 dB, 30 kHz to 50 kHz |
**10 dB, 30 kHz to 50 kHz |
|
|||
***60dB, 30 kHz to 50 kHz |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
Phase
Phase
4
System performance summaries
HP 8753ES (50-ohm systems)
Type-N test ports
Configuration |
|
Network analyzer |
HP 8753ES |
|
Standard and Option 006 |
Calibration kit |
HP 85032B |
Test-port cables |
HP 11857D |
System dynamic range |
|
30 kHz to 50 kHz |
70 dB1 |
50 kHz to 300 kHz |
90 dB1 |
300 kHz to 16 MHz |
100 dB |
16 MHz to 3 GHz |
110 dB |
Option 014 |
108 dB |
3 GHz to 6 GHz |
105 dB |
Option 014 |
103 dB |
Reflection uncertainty
Magnitude
Transmission uncertainty
Magnitude
1.Typical below 300 kHz.
2.Typical performance.
Measurement port characteristics
Frequency range
Corrected |
30 kHz-300 kHz2 |
300 kHz-1.3 GHz |
1.3 GHz-3 GHz |
3 GHz-6 GHz |
||
Directivity |
|
50 dB |
50 dB |
47 dB |
40 dB |
|
Source match |
49 dB |
42 dB |
36 dB |
31 dB |
||
Load match |
|
50 dB |
50 dB |
47 dB |
40 dB |
|
Reflection |
|
±(0.005 dB |
±(0.009 dB |
±(0.019 dB |
±(0.070 dB |
|
tracking |
|
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
|
Transmission |
|
±(0.014 dB |
±(0.013 dB |
±(0.026 dB |
±(0.065 dB |
|
tracking |
|
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Phase
Phase
5
System performance summaries
HP 8753ES (50-ohm systems)
3.5-mm test ports
Configuration |
|
Network analyzer |
HP 8753ES |
|
Standard and Option 006 |
Calibration kit |
HP 85033D |
Test-port cables |
HP 11857D |
System dynamic range |
|
30 kHz to 50 kHz |
70 dB1 |
50 kHz to 300 kHz |
90 dB1 |
300 kHz to 16 MHz |
100 dB |
16 MHz to 3 GHz |
110 dB |
Option 014 |
108 dB |
3 GHz to 6 GHz |
105 dB |
Option 014 |
103 dB |
Reflection uncertainty
Magnitude
Transmission uncertainty
Magnitude
1.Typical below 300 kHz.
2.Typical performance.
Measurement port characteristics
Frequency range
Corrected 30 kHz-300 kHz2 300 kHz-1.3 GHz |
1.3 GHz-3 GHz |
3 GHz-6 GHz |
||||
Directivity |
49 dB |
46 dB |
44 dB |
38 dB |
||
Source match |
49 dB |
44 dB |
41 dB |
37 dB |
||
Load match |
49 dB |
46 dB |
44 dB |
38 dB |
||
Reflection |
±(0.010 dB |
±(0.005 dB |
±(0.007 dB |
±(0.009 dB |
||
tracking |
+0.02/˚C) |
+0.01/˚C) |
+0.02/˚C) |
+0.03/˚C) |
||
Transmission |
±(0.016 dB |
±(0.014 dB |
±(0.022 dB |
±(0.048 dB |
||
tracking |
+0.02/˚C) |
+0.01/˚C) |
+0.02/˚C) |
+0.03/˚C) |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Phase
Phase
6
System performance summaries
HP 8753ES (75-ohm systems)
Type-N test ports
Configuration |
|
Network analyzer |
HP 8753ES Option 075 |
Calibration kit |
HP 85036B |
Test-port cables |
HP 11857B |
System dynamic range |
|
30 kHz to 50 kHz |
68 dB1 |
50 kHz to 300 kHz |
90 dB1 |
300 kHz to 16 MHz |
96 dB |
16 MHz to 3 GHz |
106 dB |
Reflection uncertainty
Magnitude
Transmission uncertainty
Magnitude
1.Typical below 300 kHz.
2.Typical performance.
Measurement port characteristics
Frequency range
Corrected |
30 kHz - 300 kHz2 |
300 kHz - 1.3 GHz |
1.3 GHz - 3 GHz |
|||
Directivity |
|
48 dB |
48 dB |
43 dB |
||
Source match |
|
47 dB |
41 dB |
35 dB |
||
Load match |
|
48 dB |
48 dB |
43 dB |
||
Reflection |
|
±(0.004 dB |
±(0.010 dB |
±(0.019 dB |
||
tracking |
|
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
||
Transmission |
|
±0.018 dB |
±(0.016 dB |
±(0.033 dB |
||
tracking |
|
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
||
Uncorrected2 |
30 kHz - 300 kHz |
300 kHz - 1.3 GHz |
1.3 GHz - 3 GHz |
|||
Directivity |
|
20 dB* |
35 dB |
30 dB |
||
Source match |
|
16 dB** |
16 dB |
16 dB |
||
Load match |
|
15 dB** |
18 dB |
16 dB |
||
Reflection |
|
±2.5 dB |
±1 dB |
±1 dB |
||
tracking |
|
|
|
|
|
|
Transmission |
|
±2.5 dB |
±1 dB |
±1 dB |
||
tracking |
|
|
|
|
|
|
Crosstalk |
|
90 dB*** |
100 dB |
100 dB |
||
* 15 dB, 30 to 50 kHz |
**10 dB, 30 to 50 kHz *** 60 dB, 30 to 50 kHz |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Phase
Phase
7
System performance summaries
HP 8753ES (75-ohm systems)
Type-F test ports
Configuration |
|
Network analyzer |
HP 8753E Option 075 |
Calibration kit |
HP 85039B |
Test-port cables |
HP 11857B |
System dynamic range |
|
30 kHz to 50 kHz |
68 dB1 |
50 kHz to 300 kHz |
90 dB1 |
300 kHz to 16 MHz |
96 dB |
16 MHz to 3 GHz |
106 dB |
Reflection uncertainty
Magnitude
Transmission uncertainty
Magnitude
1.Typical below 300 kHz.
2.Typical performance.
Measurement port characteristics
Data is shown for a Type-F female reflection port and a Type-F male transmission port.
Frequency range
Corrected2 |
30 kHz-300 kHz |
300 kHz-1.3 GHz |
1.3 GHz-3 GHz |
||
Directivity |
45 dB |
45 dB |
40 dB |
||
Source match |
40 dB |
40 dB |
30 dB |
||
Load match |
45 dB |
45 dB |
40 dB |
||
Reflection |
±(0.060 dB |
±(0.060 dB |
±(0.024 dB |
||
tracking |
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
||
Transmission |
±(0.033 dB |
±(0.019 dB |
±(0.057 dB |
||
tracking |
+0.02 dB/˚C) |
+0.01 dB/˚C) |
+0.02 dB/˚C) |
||
|
|
|
|
|
|
|
|
|
|
|
|
Phase
Phase
8
System performance summaries
HP 8753ET (50-ohm systems)
Type-N test ports
Configuration |
|
|
|
|
Network analyzer |
HP 8753ET Standard, |
|||
|
|
Option 006 or Option 004 |
||
Calibration kit |
|
HP 85032B |
||
Test port cable |
|
HP part number 8120-4781 |
||
System dynamic range |
|
|
|
|
300 kHz to 16 MHz |
100 dB |
|
|
|
16 MHz to 3 GHz |
110 dB |
|
|
|
3 GHz to 6 GHz |
|
105 dB |
|
|
Measurement port characteristics |
|
|
||
|
|
|
||
|
Frequency range |
|||
Uncorrected 300 kHz-1.3 GHz 1.3 GHz-3.0 GHz |
3.0 GHz-6.0 GHz |
|||
Directivity |
30 dB |
24 dB |
19 dB |
|
Source match4 |
25 dB |
20 dB |
14 dB |
|
Load match |
24 dB |
19 dB |
16 dB |
|
Reflection tracking |
±1.0 dB |
±1.0 dB |
±2.0 dB |
|
Transmission tracking |
±1.5 dB |
±1.5 dB |
±2.5 dB |
|
Crosstalk |
100 dB |
100 dB |
90 dB |
|
Transmission uncertainty: (enhanced-response calibration)
Transmission uncertainty: (response calibration)
Reflection uncertainty (one-port calibration)
Frequency range (continued)
|
Corrected |
300 kHz-1.3 GHz |
1.3 GHz-3.0 GHz 3.0 GHz-6.0 GHz |
||
|
Reflection measurements1 |
|
|
|
|
Directivity |
|
50 dB |
47 dB |
40 dB |
|
Source match |
|
42 dB |
36 dB |
31 dB |
|
Load match |
|
|
|
|
|
|
One-port cal |
|
24 dB |
19 dB |
16 dB |
|
Enhanced reflection cal |
24 dB |
19 dB |
16 dB |
|
Reflection tracking |
|
±(0.009 dB |
±(0.019 dB |
±(0.07 dB |
|
|
|
|
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
Transmission measurements2 |
|
|
|||
Source match |
|
|
|
|
|
|
Enhanced-response cal |
42 dB |
36 dB |
31 dB |
|
|
Response-only cal3 |
|
25 dB |
20 dB |
14 dB |
Transmission tracking |
|
|
|
|
|
|
Enhanced-response cal |
±(0.006 dB |
±(0.018 dB |
±(0.054 dB |
|
|
|
|
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
|
Response-only cal |
|
±(0.033 dB |
±(0.1 dB |
±(0.27 dB |
|
|
|
+0.01 dB/˚C) |
+0.02 dB/˚C) |
+0.03 dB/˚C) |
1. |
One-port or enhanced-response calibration. |
|
2. |
Enhanced-response or response-only calibration. |
|
3. |
2 dB less with Option 004. |
|
4. |
Option 004 may degrade uncorrected source match as much as 2 dB. |
|
9 |
||
|
|
|
Loading...