Hotpoint FDUD 43133, ULTIMA User Manual

Instructions for use

DISHWASHER

GB

English, 1

Contents

Product fiche, 2

Precautions and safety advice, 3-4

General safety

Disposal of old electrical appliances

Saving energy and respecting the environment Recycling & Disposal Information

Installation, 5-6-7

Positioning and levelling

Connecting the electricity and water supplies Technical data

Switching the appliance on for the first time Selecting the language

Child safety lock

FDUD 43133 ULTIMA

Description of the appliance, 8

Overall view Control panel

Loading the racks, 9-10

Lower rack

Cutlery basket

Upper rack

Adjusting the upper rack

Start-up and use, 11

Starting the dishwasher

Measuring out the detergent

Wash cycles, 12

Table of wash cycles

Special wash cycles and options, 13

Rinse aid and refined salt, 14

Measuring out the rinse aid Measuring out the refined salt

Care and maintenance, 15

Cutting off the water and electricity supplies Cleaning the dishwasher

Preventing unpleasant odours Cleaning the sprayer arms Cleaning the water inlet filter Cleaning the filters

Leaving the machine unused for extended periods

Troubleshooting, 16

After-Sales Service, 17

Guarantee, 18

Product fiche

GB		Product Fiche
		Brand			HOTPOINT
		Model			FDUD 43133P - FDUD 43133X
		Rated capacity in standard place settings (1)			14
		Energy efficiency class on a scale from A+++ (low consumption) to D	(high consumption)		A+++
		Energy consumption per year in kWh (2)			237.0
		Energy consumption of the standard cleaning cycle in kWh			0.83
		Power consumption of the off-mode in W			0.5
		Power consumption of the left-on mode in W			5.0
		Water consumption per year in litres (3)			2520.0
		Drying efficacy class on a scale from G (low efficacy) to A (high efficacy)			A
		Programme time for standard cleaning cycle in minutes			190
		The duration of the left-on mode in minutes			10
		Noise in dB(A) Re 1pW			42
		Built-in model			NO
		NOTES
		1) The information on the label and fiche relates to the standard cleaning cycle, this programme is suitable to clean normally
		soiled tableware and it is the most efficient programme in terms of combined energy and water consumption. The standard
		cleaning cycle corresponds to the Eco cycle.
		2) Based on 280 standard cleaning cycles using cold water fill and the consumption of the low power modes. Actual energy
		consumption depends on how the appliance is used.
		3) Based on 280 standard cleaning cycles. Actual water consumption	depends on how the appliance is used.

2

Precautions and safety advice

The appliance was designed and manufactured in compliance with current international safety standards. The following information has been provided for safety reasons and should therefore be read carefully.

Keep this instruction manual in a safe place for future reference. If the appliance is sold, given away or moved, please ensure the manual is kept with the machine, so that the new owner may benefit from the advice contained within it.

Please read this instruction manual carefully: it contains important information regarding the safe installation, use and maintenance of the appliance.

This appliance is intended to be used in household and similar applications such as:

-staff kitchen areas in shops, offices and other working environments;

-farm houses;

-by clients in hotels, motels and other residential type environments;

-bed and breakfast type environments.

General safety

•This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•Children should be supervised to ensure that they do not play with the appliance.

•The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use.

•The appliance must be used by adults only, to wash domestic crockery according to the instructions in this manual.

•The appliance must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the machine exposed to rain and storms.

•Do not touch the appliance when barefoot.

•When unplugging the appliance always pull the plug from the mains socket, do not pull on the cable.

•The water supply tap must be shut off and the plug should be removed from the electrical socket before cleaning the appliance or carrying out any maintenance work.

•If the appliance breaks down, do not under any circumstances touch the internal parts in an attempt to carry out the repair work yourself.

•Do not lean or sit on the open door of the appliance: this may cause the appliance to overturn.

•The door should not be left open as it may create a dangerous obstacle.

	• The packaging material should not be used as a toy:	GB
	it can become a choking or suffocation hazard.

If your family includes children:

•DO NOT allow children to play with the appliance or tamper with its controls.

•Keep detergents and rinse aids away from children.

•Keep children away from the open door of a dishwasher, there could still be some detergent left inside.

Disposal of old electrical appliances

The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

Saving energy and respecting the environment

Saving water and energy

•Only start a wash cycle when the dishwasher is full. While waiting for the dishwasher to be filled, prevent unpleasant odours with the Soak cycle (see Wash Cycles).

•Select a wash cycle that is suited to the type of crockery and to the soil level of the crockery using the Wash cycle table:

-for dishes with a normal soil level, use the Eco wash cycle, which guarantees low energy and water consumption levels.

-if the load is smaller than usual activate the Half load* option (see Start-up and use).

•If your electricity supply contract gives details of electricity saving time bands, run wash cycles during the periods when a lower tariff is applied.

The Delayed start* button (see Start-up and use) helps you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents containing enzymes

•We strongly recommend that you use detergents that do not contain phosphates or chlorine, as these products are harmful to the environment.

3

		•	Enzymes provide a particularly effective action
	GB
			at temperatures around 50°C, and as a result
			detergents containing enzymes can be used in
			conjunction with low-temperature wash cycles in
			order to achieve the same results as a normal 65°C
			wash cycle.
		•	To avoid wasting detergent, use the product in
			appropriate quantities based on the manufacturer’s
			recommendations, the hardness of the water and the
			soil level and quantity of the crockery. Even if they
			are biodegradable, detergents contain substances
			that may alter the balance of nature.

Recycling & Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully.

To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the appliance.

Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut.

* Only available in selected models.

4

Installation

If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back.

Positioning and levelling

1.Remove the appliance from all packaging and check that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed any further with the installation process.

2.Check the dishwasher by placing it so that its sides or back panel are in contact with the adjacent cabinets or even with the wall. This appliance can also be recessed under a single

worktop* (see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If the floor is uneven, the front feet of the appliance may be adjusted until it reaches a horizontal position. If the appliance is levelled correctly, it will be more stable and much less likely to move or cause vibrations and noise while it is operating.

4*. Adjust the height of the rear foot from the front of the appliance on the central lower part of the dishwasher, turning a hexagonal spanner (red color) with an opening of 8 mm in a clockwise direction to increase the height or in an anticlockwise direction to decrease the height.

The dishwasher meets the requirements set out by the regulations in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by a trained and authorised technician: Repairs carried out by unaithorised persons will invalidate the guarantee, as well as posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions, from tampering with even a single component or from the use of non-original spare parts.

Electrical Connection

Before inserting the plug into the electrical socket, make sure that:

•the socket is earthed and complies with current regulations;

•the socket can withstand the maximum load of the appliance, which is indicated on the data plate located on the inside of the door (see Description of the appliance);

•the power supply voltage falls within the values indicated on the data plate on the inside of the door;

•the socket is compatible with the plug of the appliance. If this is not the case, ask an authorised technician to replace the plug (see After Sales Service); do not use extension cables or multiple sockets.

Once the appliance has been installed, the power supply cable and the electrical socket should be easily accessible.

	The cable should not be bent or compressed.	GB

If the power supply cable is damaged, it must be replaced by the manufacturer or its Technical Assistance Service in order to prevent all potential hazards. (See After Sales Service)

This appliance must be earthed.

Fuses:your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only those rated at 13A and ASTA approved to BS1362 should be used. If you lose the fuse cover, a replacement may be obtained from your local authorised Service

Centre or Electrical company. Correct replacement is identified by colour coding or the marking on base of plug.

DO NOT use the plug unless the fuse cover is fitted.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

To avoid a shock hazard DO NOT insert the discarded plug into a socket anywhere else.

Wires in the mains lead are coloured accordance with the following code:

Green/Yellow	-	Earth
Blue	-	Neutral
Brown	-	Live

If you change the plug, the colour of the wires in the mains lead may not correspond with the terminal markings in the plug, which if not coloured, could be:

EARTH ‘E’	or
NEUTRAL	‘N’
LIVE	‘L’

Changing the Mains Lead

A lead can be ordered from Hotpoint Service

UK: 08709 066 066 or

Republic of Ireland: 1850 302 220

-If you have damaged the existing lead or require a longer one a charge will be made. It is strongly advised that this work is carried out by a qualified electrician.

-If the domestic wiring includes a residual current-operated circuit breaker, ensure that it conforms to the latest regulations.

The dishwasher must not be connected to the electricity supply while installation is being carried out.

-This appliance should only be connected to a 230/240V AC source, via a properly installed earthed socket.

-Use the dishwasher solely in a domestic environment.

-DO NOT stand or place heavy objects on the door when it is open, this could damage the door or cause the appliance to tip forward.

5

	GB			The Company shall not be held responsible for any
		incidents that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation which may form.

Technical data

Dimensions			width 60 cm
			height 85 cm
			depth 60 cm
Capacity			14 standard place-settings
Water supply			0,05 ÷ 1MPa (0.5 ÷ 10 bar)
pressure			7,25 – 145 psi
Power supply voltage			See appliance data plate
Total absorbed power			See appliance data plate
Fuse			See appliance data plate
			This dishwasher conforms to the
			following European Community
			Directives:
			-2006/95/EC (Low Voltage)
			-2004/108/EC (Electromagnetic
			Compatibility)
			-2009/125/EC (Comm. Reg.
			1016/2010) (Ecodesign)
			-97/17/EC (Labelling)
			-2012/19/EU Waste Electrical
			and Electronic Equipment
			(WEEE)

Connecting the water supplies

Connection to the water and electricity supplies should only be performed by a qualified technician.

The dishwasher should not stand on top of the water hoses or the electricity supply cable.

Connecting the water inlet hose

The water inlet and outlet hoses and the electricity supply cable may be positioned towards the right or the left in order to achieve the best possible installation.

•To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection.

•To a suitable hot water connection point: your dishwasher may be provided with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a cold water supply.

If the inlet hose is not long enough, contact a specialist store or an authorised technician (see Assistance).

The water pressure must be within the values indicated in the Technical data table (see Installation).

The hose should not be bent or compressed.

The appliance must be connected to the water supply network using new hoses.

Do not use old hoses.

Ensure that the new hose supplied is connected and the old hose is disposed of safely.

DO NOT overtighten the hose connector, hand tight is sufficient.

Ensure the fill hose is not kinked.

Tap connections*: A range of adaptors are available to suit your tap.

DO NOT connect the dishwasher to a single outlet instantaneous water heater or an electric heater.

Sink Waste System

Connect the outlet hose (without bending it) to a drain duct with a minimum diameter of 32 mm.

The outlet hose must be at a height ranging from 40 to 80 cm (from 15’’ to 31’’) from the floor/surface where the dishwasher rests (A).

•before connecting the drain hose, remove any internal restrictions; this will prevent a build up of debris which could cause a blockage

•remove any restrictions from the waste spigot and ensure that the sealing bung is removed (B).

It MUST NOT be connected to a surface water drain.

• Untie the end of the GREY drainage hose from the rear of the appliance.

* Only available in selected models.

6