Hotpoint NCD 191 I User Manual

0 (0)

Operating Instructions

FRIDGE

 

 

 

 

 

 

 

 

Contents

 

 

 

 

EN

 

 

 

 

 

 

 

Installation, 2-3

 

 

EN

 

 

 

 

Positioning and connection

 

 

 

Description of the appliance, 4

 

English, 1

 

 

 

Overall view

 

 

 

Accessories, 5

 

 

 

Start-up and use, 5

 

 

 

Starting the appliance

 

 

 

Chiller system

 

 

 

Using the refrigerator to its full potential

 

 

 

Maintenance and care, 6

 

 

 

Switching the appliance off

 

 

 

Cleaning the appliance

 

 

 

Avoiding mould and unpleasant odours

 

NCD 191 I

Defrosting the appliance

 

Replacing the light bulb

 

 

 

 

 

 

Precautions and tips, 7

 

 

 

General safety

 

 

 

Disposal

 

 

 

Respecting and conserving the environment

 

 

 

Troubleshooting, 8

 

 

 

Guarantee, 9

 

 

 

After Sales Service, 10

Installation

! Before placing your new appliance into operation EN please read these operating instructions carefully.

They contain important information for safe use, for installation and for care of the appliance.

! Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.

Positioning and connection

Positioning

1.Place the appliance in a well-ventilated humidityfree room.

2.Do not obstruct the rear fan grills. The compressor and condenser give off heat and require good ventilation to operate correctly and save energy.

3.Ensure the appliance is away from any sources of heat (direct sunlight, electric stove, etc.).

Levelling

1.Install the appliance on a level and rigid floor.

2.If the floor is not perfectly horizontal, adjust the refrigerator by tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it vertically and wait at least 3 hours before connecting it to the electricity mains. Before inserting the plug into the electrical socket ensure the following:

The appliance is earthed and the plug is compliant with the law.

The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the right side of the horizontal surface in the top compartment, under the thermostat (e.g. 150 W).

The voltage is within the range of values indicated on the data plate located on the right side of the horizontal surface in the top compartment, under the thermostat (e.g. 220-240V).

The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an authorised technician to replace it (see Assistance). Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

!The cable must not be bent or compressed.

!The cable must be checked regularly and replaced by authorised technicians only (see Assistance).

!The manufacturer declines any liability should these safety measures not be observed.

Your appliance is supplied with a 13amp fused plug that can be plugged into a 13amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING:

THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re-fitted.

If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug and you should wish to remove it to add a longer cable or to re-route the mains cable through partitions, units etc. please ensure that either:

-The plug is replaced by a fused 13amp rewireable plug bearing the BSI mark of approval.

or

-The mains cable is wired directly into a 13amp cable outlet, controlled by a switch (in compliance with BS 5733) which is accessible without moving the appliance.

Disposing of the plug

Cut off and dispose of the supplied plug if it does not fit your socket. The cable should be cut as close as possible to the moulded plug.

Remove the fuse.

WARNING:

To avoid a shock hazard do not insert the discarded plug into a socket anywhere else.

2

Fitting a new plug

EN

IMPORTANT:

WIRES IN THE MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE...

Green and Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

-Connect Green and Yellow wire to terminal

marked 'E' or

or coloured

Green and

Yellow.

-Connect Brown wire to terminal marked 'L' or coloured red or brown.

-Connect Blue wire to terminal marked 'N' or coloured Black or Blue.

If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse. A 15amp plug must be protected by a 15amp fuse, either in the plug or adaptor or at the distribution board.

If you are in any doubt about the electrical supply to your machine, consult a qualified electrician before use.

CE Marking certifies that this appliance conforms to the following EEC directives : Low Voltage Equipment - 73/23/EEC & 93/68 EEC

Electromagnetic Compatibility 89/336/EEC, 92/ 31/EEC & 93/68/EEC

3

Hotpoint NCD 191 I User Manual

Description of the appliance

Overall view

EN

The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not directly represent the appliance purchased. For more complex features, consult the following pages.

WINE AREA

FRUIT and

 

VEGETABLE bin

TEMPERATURE MULTI-USE box with CONTROL

EGG TRAY and

BUTTER DISH *

PROFESSIONAL

BOTTLE SHELF

containers

compartment

Varies by number and/or position. * Available only on certain models.

4

Loading...
+ 8 hidden pages