Hotpoint FZM84, FZA54, FZM54, FZA84 User Manual

0 (0)
FREEZER - MODELS FZA54, FZM54, FZA84, FZM84
INSTRUCTIONS FOR INSTALLATION & USE
GETTING STARTED:
To ensure that your freezer runs reliably and efficiently follow these steps.
Choose a location for your
freezer,away from any
heat sources and allow
adequate ventilation -
gap above.
Level the freezer by
adjusting the front feet.
This will stop rocking or
vibration and keep the
door aligned.
If you are freezing fresh
food,turn on fast freeze by
pressing the switch 24
hours before placing the
food inside.
Place the fresh food
inside.
Remember to turn fast freeze off
after 24 hours, however if you
forget to do so it will automatically
cancel after 48 hours.
Move the freezer into
position, using the sides
of the cabinet. Take care
to avoid damaging the
refrigerant circuit pipe
work on the rear.
Plug in and switch on.
Allow the freezer to cool
before placing food inside.
The high temperature
light will stay on until the
freezer has cooled down.
All food in the freezer
should be covered.
Read the rest of these instructions to get the best from your appliance
and remember to fill in your guarantee registration.
Keep this Book in a safe place for quick reference.
STEP 1
STEP 2
STEP 3
STEP 5
STEP 6
STEP 7
SAFETY &
INSTALLATION CONTROLS USEFUL ADVICE
CLEANING &
MAINTENANCE
TROUBLESHOOTING
SERVICE &
GUARANTEE
Your freezer is now
working.
If after 24 hours your
freezer is not operating as
you want, refer to the
TROUBLESHOOTING
section.
Before plugging in and
switching on, leave the
freezer in its final
location for at least 15
minutes to allow it to
settle.
STEP 4
NB.The spanner is for illustration
only and is not supplied with the
freezer.
For Your Safety
For your safety, read the following advice:
The freezer cooling system contains a small amount of gas which is environmentally
friendly but flammable. To avoid any risk :-
Install the freezer following the installation instructions and ensure
that ventilation openings are kept clear of obstruction.
Take care when installing or moving the freezer to avoid damaging
the pipes on the rear.
If you suspect a leak, do not switch on the freezer,but open the
windows and doors to ventilate the room.
Do not use any electrical devices inside the freezer, for instance for
defrosting.
Do not use any mechanical devices for defrosting other than any which may
have been supplied with the freezer as they may cause damage.
Only use this freezer for storing domestic foodstuffs.
When installing your freezer :-
Ensure that the mains cable is not trapped underneath or behind the freezer
when you install or move it.
Do not stack any other appliance on top of this freezer as they may
damage the freezer or become unstable.
When using your freezer :-
Do not sit or stand on top of your freezer.
Do not store poisonous, flammable or dangerous substances in your freezer.
Do not use aerosol sprays for defrosting or cleaning your freezer.
If you sell the freezer, pass on this booklet to the new owner.
2
SAFETY &
INSTALLATION
Installation
3
Minimum space required to open door
The freezer needs a space of 600mm (24 inches) in front to allow the door to
open.
When positioning the freezer next to a unit, a gap of 30mm (1
1
/
4
inch) can be left
at the hinge side of the door to allow the easy removal of furniture.If preferred
the freezer can be positioned so that a gap is not left.This will restrict how far the
door can be opened but the furniture can still be removed (see diagrams below).
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’
in the CLEANING & MAINTENANCE section).
SAFETY &
INSTALLATION
TOP VIEW
TOP VIEW
less than 30mm
30mm or more
600mm
600mm
Location & Air Circulation
Locate your freezer away from sources of heat e.g.
cookers, radiators, direct sunlight as extreme temperature
will affect its performance.
Allow a minimum 100mm (4 inches) between the top of
the freezer and the ceiling or the underside of a wall
cupboard.
Providing you follow the recommended ventilation
requirements you will :-
Prolong the life of the freezer.
Minimise the risk of condensation on the outside of
the freezer.
Minimise the running costs.
Minimise operating sounds caused by vibration.
100mm
(4 inches)
Installation
Levelling:
Level the freezer when it is in its final location by adjusting the front feet, until firm
contact is made with the floor. This will stop rocking or vibration and keep the door
aligned which helps the freezer run reliably and efficiently.
Note: Before plugging in and switching on,leave the freezer standing in its
final location for at least 15 minutes to allow it to settle.
4
SAFETY &
INSTALLATION
Installation
Electrical Supply
WARNING:This appliance must be earthed.
The appliance must be positioned so that the plug is accessible after
installation.
Fuses
Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the
fuse, only use those rated at 13A and ASTA approved to BS1362.
Changing the Plug
Cut off and dispose of the supplied plug if it does not fit your socket.
WARNING:To avoid a shock hazard do not insert the discarded plug into a socket
anywhere else.
IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE :
Green/Yellow - Earth
Blue - Neutral Brown - Live
If you change the plug, the colour of wires in the mains lead may not correspond with
the colour of the markings identifying terminals in the plug. You should therefore
wire it as shown above.
Changing the Mains Lead
This appliance is fitted with a special mains lead. If you need to replace the mains
lead due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS,
back page). It is strongly advised that this work is carried out by a qualified
electrician.
CE Marking certifies that this appliance conforms to the following EEC
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC
5
SAFETY &
INSTALLATION
Controls
Controlling the Temperature of the Freezer Compartment
The control wheel on the front panel adjusts the internal freezer temperature.
The internal freezer temperature should be -18˚C or colder.
The setting of the control wheel will depend on the location of the freezer, the room
temperature and how often the door is opened. The normal set point (marked by a 3
on the dial) is usually suitable. If you need to adjust the temperature turn the control
wheel using a coin to avoid damage:
Clockwise (higher number) - Colder
Anti-clockwise (lower number) - Warmer
6
You can check the temperature of the freezer compartment by using a Fridge Freezer
Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order
Hotline (see KEY CONTACTS back page).
WARNING: Do not use a mercury filled thermometer,as breakage would cause a
health hazard.
Your freezer must NOT be placed in a room where the temperature goes below 2˚C or
above 38˚C for prolonged periods,as the internal freezer temperature will not be
maintained.
CONTROLS
Loading...
+ 14 hidden pages