Hotpoint FZM81, FZM51, FZA81, FZA51 User Manual

FREEZER - MODELS FZA51, FZM51, FZA81, FZM81 INSTRUCTIONS FOR INSTALLATION & USE

GETTING STARTED: To ensure that your freezer runs reliably and efficiently follow these steps.

STEP 1		STEP 2
Choose a location for your		Move the freezer into
freezer, away from any		position, using the sides
heat sources and allow		of the cabinet. Take care
adequate ventilation -		to avoid damaging the
100mm (4 inches)		refrigerant circuit pipe
gap above.		work on the rear.

STEP 3

Level the freezer by adjusting the front feet This will stop rocking or vibration and keep the door aligned

NB. The spanner is for illustration only and is not supplied with the freezer

STEP 5

Plug in and switch on. Allow the freezer to cool before placing food inside. The high temperature light will stay on until the freezer has cooled down.

All food in the freezer should be covered.

STEP 4

Before plugging in and switching on, leave the freezer in its final location for at least 15 minutes to allow it to settle.

STEP 6

If you are freezing fresh food, turn on fast freeze by pressing the switch 24 hours before placing the food inside.

Place the fresh food inside.

Remember to turn fast freeze off after 24 hours, however if you forget to do so it will automatically cancel after 48 hours.

STEP 7

Your freezer is now working.

If after 24 hours your freezer is not operating as you want, refer to the TROUBLESHOOTING section.

Read the rest of these instructions to get the best from your appliance and remember to fill in your guarantee registration.

Keep this Book in a safe place for quick reference.

INSTALLATION	& SAFETY
CONTROLS
ADVICE USEFUL
MAINTENANCE	&CLEANING
TROUBLESHOOTING
GUARANTEE	& SERVICE

		For Your Safety
	For your safety, read the following advice:
	The freezer cooling system contains a small amount of gas which is environmentally
	friendly but flammable. To avoid any risk :-
	●	Install the freezer following the installation instructions and ensure
		that ventilation openings are kept clear of obstruction.
	●	Take care when installing or moving the freezer to avoid damaging
SAFETY& INSTALLATION	●	the pipes on the rear.
		defrosting.
		If you suspect a leak, do not switch on the freezer, but open the
		windows and doors to ventilate the room.
	●	Do not use any electrical devices inside the freezer, for instance for
	●	Do not use any mechanical devices for defrosting other than any which may
		have been supplied with the freezer as they may cause damage.
	●	Only use this freezer for storing domestic foodstuffs.
	When installing your freezer :-
	●	Ensure that the mains cable is not trapped underneath or behind the freezer
		when you install or move it.
	●	Do not stack any other appliance on top of this freezer as they may
		damage the freezer or become unstable.
	When using your freezer :-
	●	Do not sit or stand on top of your freezer.
	●	Do not store poisonous, flammable or dangerous substances in your freezer.
	●	Do not use aerosol sprays for defrosting or cleaning your freezer.

If you sell the freezer, pass on this booklet to the new owner.

2

Installation

Location & Air Circulation

Locate your freezer away from sources of heat e.g. cookers, radiators, direct sunlight as extreme temperature will affect its performance.

Allow a minimum 100mm (4 inches) between the top of the freezer and the ceiling or the underside of a wall cupboard.

Providing you follow the recommended ventilation requirements you will :-

●Prolong the life of the freezer.

●Minimise the risk of condensation on the outside of the freezer.

●Minimise the running costs.

●Minimise operating sounds caused by vibration.

100mm (4 inches)

Minimum space required to open door

The freezer needs a space of 600mm (24 inches) in front to allow the door to open.

When positioning the freezer next to a unit, a gap of 30mm (11/4 inch) can be left at the hinge side of the door to allow the easy removal of furniture. If preferred the freezer can be positioned so that a gap is not left. This will restrict how far the door can be opened but the furniture can still be removed (see diagrams below). The door hinge side can be changed to make it easier to open (see ‘Door Reversal’ in the CLEANING & MAINTENANCE section).

TOP VIEW

TOP VIEW

600mm		600mm

30mm or more

less than 30mm

INSTALLATION	& SAFETY

3

Installation

Levelling:

Level the freezer when it is in its final location by adjusting the front feet, until firm contact is made with the floor. This will stop rocking or vibration and keep the door aligned which helps the freezer run reliably and efficiently.

Note: Before plugging in and switching on, leave the freezer standing in its final location for at least 15 minutes to allow it to settle.

SAFETY &	INSTALLATION

4

Installation

Electrical Supply

WARNING: This appliance must be earthed.

The appliance must be positioned so that the plug is accessible after installation.

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only use those rated at 13A and ASTA approved to BS1362.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into a socket anywhere else.

IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE :

Green/Yellow - Earth

Blue	- Neutral				Brown - Live

If you change the plug, the colour of wires in the mains lead may not correspond with the colour of the markings identifying terminals in the plug. You should therefore wire it as shown above.

Changing the Mains Lead

This appliance is fitted with a special mains lead. If you need to replace the mains lead due to damage, one can be bought from Hotpoint Service (see KEY CONTACTS, back page). It is strongly advised that this work is carried out by a qualified electrician.

CE Marking certifies that this appliance conforms to the following EEC directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC

INSTALLATION	& SAFETY

5

Controls

Controlling the Temperature of the Freezer Compartment

The control wheel on the front panel adjusts the internal freezer temperature. The internal freezer temperature should be -18˚C or colder.

The setting of the control wheel will depend on the location of the freezer, the room temperature and how often the door is opened. The normal set point (marked by a 3 on the dial) is usually suitable. If you need to adjust the temperature turn the control wheel using a coin to avoid damage:

Clockwise (higher number) - Colder

Anti-clockwise (lower number) - Warmer

CONTROLS

You can check the temperature of the freezer compartment by using a Fridge Freezer Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order Hotline (see KEY CONTACTS back page).

WARNING: Do not use a mercury filled thermometer, as breakage would cause a health hazard.

Your freezer must NOT be placed in a room where the temperature goes below 2˚C or above 38˚C for prolonged periods, as the internal freezer temperature will not be maintained.

6