n Description
This programmable thermostat can be connected to an electric heating system such as an electric baseboard, a radiant ceiling, a floor heating system, an electric convector, etc. It is not compatible with a central heating system.
|
Time and day |
|
|
Appears during the |
|
On/Off |
setpoint display |
|
switch |
Temperature |
|
|
||
Operating |
Preset temperature |
|
mode icons |
||
|
icons |
|
Heating |
|
|
indicator |
To set the day |
|
Periods |
To set the time |
|
Temperature |
To program the schedule |
|
To skip a period |
||
preset buttons |
||
|
||
Temperature |
To select the |
|
operating mode |
||
adjustment |
||
|
*Set the switch to Off to cut power to the heater. This will not affect the time and temperature settings.
o Connection
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRICAL SHOCK.
•The installation must be carried out by an electrician.
•All cables and connections must conform to the local electrical code.
•Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.
•Install the thermostat onto an electrical box.
•Install the thermostat about 5 feet high, on an inside wall facing the heater.
•Avoid locations where there are air drafts (such as the top of a staircase or an air outlet), dead air spots (such as behind a door), or direct sunlight.
•Do not install the thermostat on a wall that conceals chimney or stove pipes.
n Connect the thermostat wires to the |
|
Black |
power and to the load using solderless |
Load |
Power |
connectors for copper wires. |
|
Red |
o Push the excess wire back into the |
|
|
|
|
electrical box to prevent interference with the thermostat.
pSecure the thermostat using two 6-32 screws.
q Return power to heating system.
NOTE: Always keep the thermostat's vents clean and unobstructed.
Load
08161 / TH110-DP-P / TL8230
Programmable Thermostat - Installation and User Guide
08161 TH110-DP-P TL8230
p Configuration
The configuration switches are on the back of the thermostat. Default (factory) settings are inside the gray cells.
# |
Configurations |
UP |
DN |
|
|
|
|
SW1 |
Not used |
|
|
SW2 |
Early Start a |
Disable |
Enable |
SW3 |
Time format |
12-hour |
24-hour |
SW4 |
Temperature format b |
°F |
°C |
a.Early Start can be used in Automatic mode only. When this function is enabled, the thermostat calculates the optimal time to start heating in order to obtain the desired temperature by the set time. The thermostat re-assesses the start time daily based on the previous day’s performance.
b.If you change the temperature display format, the preset temperatures ( , and ) will return to their default settings.
q Power-up
Upon power-up, the thermostat is in manual mode () and displays the actual temperature.
n Press the Hour and Min buttons to set the thermostat’s clock. o Press the Day button to set the day.
r Temperature Setting
Setpoint
The thermostat normally displays the actual temperature. To view the setpoint, press the or button briefly. The setpoint will appear for the next 5 seconds.
To change the setpoint, press the or button until the desired temperature is displayed. To scroll faster, hold the button.
Using a preset temperature
The thermostat has 3 preset temperatures:
Comfort temperature Economy temperature Vacation temperature
Icon |
Intended use |
Default setting |
|
Comfort (when at home) |
70 °F (21 °C) |
|
|
|
|
Economy (when asleep or away from home) |
62 °F (16 °C) |
|
|
|
|
Vacation (during prolonged absence) |
50 °F (10 °C) |
|
|
|
•To use the Comfort or Economy temperature, press the or button respectively. The corresponding icon will be displayed.
•To use the Vacation temperature, press both and buttons simultaneously. The icon will be displayed.
Storing a preset temperature
To store the Comfort or Economy temperature:
Set the desired temperature using the or button. Press and hold
the appropriate button ( or ) for approximately 3 seconds until the corresponding icon is displayed.
To store the Vacation temperature:
Set the desired temperature using the or button. Press and hold both and buttons simultaneously for approximately 3 seconds until the icon is displayed. Press the Mode button.
69-2023 |
1/11/06 |
1/2 |