Operating
Manual
RTH111 Series
Non-Programmable Thermostat
69-2603ES-01
Table of contents |
|
About your new thermostat |
|
Thermostat features................................... |
1 |
Quick reference to controls....................... |
3 |
Quick reference to display......................... |
4 |
Operation |
|
Select system setting................................. |
5 |
Select fan setting........................................ |
6 |
Adjust the temperature.............................. |
7 |
Compressor protection.............................. |
8 |
Appendices |
|
Battery replacement................................... |
9 |
Customer assistance................................ |
10 |
In case of difficulty................................... |
11 |
Limited warranty....................................... |
13 |
CAUTION: EQUIPMENT DAMAGE HAZARD.
To prevent possible compressor damage, do not operate cooling system when outdoor
temperature is below 50°F (10°C).
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502
Read and save these instructions.
® U.S. Registered Trademark. Patents pending. Copyright © 2011 Honeywell International Inc. All rights reserved.
Operating Manual |
RTH111 |
About your new thermostat
Your new Honeywell thermostat has been designed to give you many years of reliable service and easy-to-use, push-button climate control.
Features
•Displays ambient (measured) temperature at all times
•One-touch access to setpoint temperature
•Built-in compressor protection
1 |
69-2603ES—01 |
Operating Manual
ThisAboutthermostatyour new thermostatisready to go!
Simply perform the three steps below and the thermostat is in operation:
1. |
Select system setting: Preset to Off................................ |
To change, see page 5 |
2. |
Select fan setting: Preset to Auto................................... |
To change, see page 6 |
3.Set the temperature using the
Up or Down buttons....................................................... |
To change, see pages 7 |
69-2603ES—01 |
2 |
RTH111
QuickAbout referenceyournew thermostattocontrols
Up/Down buttons
Press to adjust temperature.
|
Fan |
Heat Off Cool |
Auto On |
System switch (see page 5)
•Cool: Cooling system control.
•Off: All systems off.
•Heat: Heating system control.
Fan Switch (see page 6) On: Fan runs continuously.
Auto: Fan runs only when heating or cooling system is on.
3 |
69-2603ES—01 |
Operating Manual
QuickAbout referenceyournew thermostattodisplay screen
Setpoint indicator
Appears when the setpoint temperature is displayed
Low battery warning
(see page 9)
Set
Lo
Batt
77
Cool
On
M32763
Temperature
The ambient (measured) temperature is normally displayed. To view the setpoint temperature, press the Up or Down button once. The setpoint temperature will appear for five seconds.
System status
Cool on: Cooling system is on. Heat on: Heating system is on.
When Cool On is flashing, compressor protection is engaged (see page 8).
69-2603ES—01 |
4 |
RTH111
Select the system setting
The SYSTEM switch can be set to control your heating or cooling system, depending on the season.
• Cool: Cooling system control.
• Off: All systems are off.
• Heat: Heating system control.
|
Fan |
Heat Off Cool |
Auto On |
Set SYSTEM switch to control the heating or cooling system.
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
5 |
69-2603ES—01 |
Operating Manual
Select the fan setting
Set the FAN switch to Auto or On.
In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on.
If set to “On,” the fan runs continuously.
|
Fan |
Heat Off Cool |
Auto On |
Set FAN switch to choose whether the fan runs continuously or only as needed.
69-2603ES—01 |
6 |
RTH111
Adjustboutyourthetemperaturenewthermostat
Press σ or τ to adjust the temperature.
Note: Make sure the thermostat is set to the
system you want to control (heat or cool).
Set 77
Cool
On
|
Fan |
Heat Off Cool |
Auto On |
7 |
69-2603ES—01 |
Operating Manual
Built-in compressor protection
Set 77
Cool
On
M32769
Message flashes until safe restart time has elapsed.
This feature helps prevent damage to the compressor in your air conditioning or heat pump system.
Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait 5 minutes before restarting.
During the wait time, the display will flash the message Cool On. When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
69-2603ES—01 |
8 |