Honeywell HWM-335, HWM-331, HWM-330, HWM-450 User Manual

4.5 (2)
Honeywell HWM-335, HWM-331, HWM-330, HWM-450 User Manual

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 1

OWNER’S MANUAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 US GALLONS (11.3 LITERS)

4 US GALLONS (15.1 LITERS)

 

OUTPUT PER DAY

OUTPUT PER DAY

 

WARM MOISTURE HUMIDIFIERS

WARM MOISTURE HUMIDIFIER

 

Models:

Model:

 

HWM-330

HWM-450

 

HWM-331

 

 

 

 

HWM-335

 

 

 

The Honeywell trademark is used by Kaz, Inc. under license from Honeywell Intellectual Properties, Inc.

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 2

IMPORTANT SAFETY

INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS HUMIDIFIER

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1.Always place this humidifier on a firm, flat and level surface. This humidifier may not work properly on an uneven surface.

2.Do not place humidifier directly on wood furniture or other surfaces that could be damaged by water.

3.CAUTION: To reduce the risk of severe burns, place this humidifier in an area where it is not accessible to children.

4.Do not place the humidifier near any heat sources such as stoves, radiators, and heaters.

5.Before using the humidifier, check the power cord for any signs of damage. If the cord is found to be damaged, DO NOT USE and return the humidifier to the manufacturer under the warranty agreement for repair.

6.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.

7.To disconnect the humidifier, first turn controls to the OFF position, then grip the plug and pull it from the wall outlet. Never pull by the cord.

8.A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

9.The humidifier should always be unplugged and emptied when not in operation or while being serviced or cleaned.

10.Never tilt or attempt to move the humidifier while it is operating or filled with water. UNPLUG the humidifier before moving.

11.This humidifier requires regular cleaning. Refer to the CLEANING instructions provided. Never clean the humidifier in any manner other than as instructed in this manual. You may have to clean your unit once per week or more depending on the mineral content of your water.

12.Do not immerse the base in water or other liquid. Do not pour water in the humidifier outlet.

13.Do not direct steam directly at individuals, walls or furniture.

14.When a humidifier is used in a closed room or small rooms, check periodically for proper ventilation, as excessive humidity can cause condensation stains on walls.

15.Do not attempt to remove Medicine Cup, Power Unit, Water Tank, Water Tray or Mineral Absorption Pad during operation, or within 10-15 minutes after the humidifier has been turned “off” and unplugged. Serious injury may result. The Water Tray and Mineral Absorption Pad should only be removed for cleaning and maintenance purposes.

16.DO NOT touch the steam vapor. Steam can cause severe burns.

17.DO NOT block the mist grille. This will damage the humidifier.

2

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 3

Introduction

H O W D O E S I T W O R K ?

WARM MOISTURE SYSTEM:

Water passes into the unit where it is heated and purified by the QuickSteamheating plate. The unit then pulls the air through the top vent and spreads invisible, bacteria-free mist into the room.

Your humidifier is made up of these parts:

Medicine Cup

Mist Grille

Tank Handle

 

Water Tank

Power

Unit

Fill Cap

Removable Water Tray

Mineral

Absorption

Pad

Mineral Reservoir

Base

Heating Plate

3

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 4

Set-Up

NOTE: We recommend that the humidifier be disinfected prior to first use. Please see CLEANING INSTRUCTIONS.

Select a firm, level, flat location - at least six inches (15 cm) from any wall or object for proper air flow (Fig. 1). Place the humidifier on a water-resistant surface, as water can damage furniture and some flooring.

Kaz will not accept responsibility for property damage caused by water spillage.

Remove the Water Tank by grasping handle and pulling straight up (Fig. 1). Set aside.

Remove the Power Unit by grasping it and lightly tilting forward while pulling up. You will feel the unit disengage from its lock (Fig. 2). Set the Power Unit aside.

Remove the Water Tray (Fig. 3). Set the Water Tray aside.

Place one Mineral Absorption Pad flat on the Heating Plate. See the MINERAL ABSORPTION PAD section (page 5) for more information.

Replace the Water Tray.

Replace the Power Unit, making sure it is installed properly. Align the back of the Power Unit directly behind the tabs of the Base and press down firmly. You will hear a slight click. Your Power Unit will be flush with the Base (Fig. 4).

Fill the Water Tank with cool tap water (Fig. 5). See the FILLING section (page 5) for more information.

NOTE: Save your box for end of season storage. (See END OF SEASON CARE AND STORAGE section.)

Fig. 1

WALL

 

6"

Fig. 2

Power

 

Unit

Base

Fig. 3

Removable

Water Tray

Base

Fig. 4

4

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 5

Mineral Absorption Pad Instructions

CAUTION: HOT SURFACES MAY CAUSE SEVERE BURNS.

DO NOT TOUCH ANY SURFACES UNTIL THEY HAVE COOLED.

Water contains minerals and other particles. The amount of minerals varies dependent on your local water supply. It is common for these minerals to stick to your humidifier’s Heating Plate and in turn decrease the performance of your humidifier. Mineral Absorption Pads trap the minerals and help prevent stubborn mineral buildup on your Heating Plate.

Before starting your humidifier, place one Mineral Absorption Pad flat on the Heating Plate. After the humidifier has been operating, the water and all internal parts will become HOT, and caution should be exercised when handling the Mineral Absorption Pad. Please allow the humidifier water and all internal parts to cool down (at least 10-15 minutes). Use tongs or long tweezers when handling the pad to prevent burns.

The life of the Mineral Absorption Pad will vary, depending on the mineral content of the water being used. Using normal/moderate mineral content water the Mineral Absorption Pad should be changed after approximately 2 weeks of continuous use. Again, the life of the pad will vary dependent on your usage and mineral content of your water.

For indications that your Mineral Absorption Pad needs to be changed, examine it AFTER the water has cooled down to see if it is still soft and pliable. If the pad is stiff and hard you should replace it. Another sign that indicates your Mineral Absorption Pad must be changed is scale buildup on your heating plate.

Filling

Remove the Water Tank by grasping handle and pulling straight up. Set aside (Fig. 1).

Turn the Water Tank upside down so that the Fill Cap is facing

up; unscrew the Fill Cap by turning it counter-clockwise and set aside.

Fill the Water Tank with COOL tap water (Fig. 5). DO NOT USE HOT WATER. Doing so may damage the humidifier.

Distilled water is not necessary but should be considered in hard water areas to prevent mineral build-up.

Replace the fill cap by turning it clockwise .

DO NOT OVER-TIGHTEN. Turn the Water Tank right-side up.

NOTE: Do not add any medication or other additives to water.

NOTE: When carrying the filled Water Tank, please use the handle and place your other hand under the tank for additional support.

Position the Water Tank in the humidifier and push into place (Fig. 6).

Some water will flow into the Removable Tray when the filled Water Tank is properly in place.

Once the filled Water Tank has been positioned, do not attempt to move the humidifier. To avoid leaking, you should never move the humidifier while filled with water.

CAUTION: Do not pour water into the grille on the top of the humidifier. Doing so may damage the humidifier or cause personal injury.

Fig. 5

Fig. 6

5

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 6

Manual Control Operation (Models HWM-330 and HWM-331)

P O W E R

CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH

WET HANDS AS AN ELECTRICAL SHOCK COULD

OCCUR.

With the power switch in the OFF position, plug the filled humidifier into a polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way.

O U T P U T / M O I S T U R E C O N T R O L

Set the Moisture Control knob to the desired position (Fig. 7). HIGH: For fast humidifying

LOW: For everyday moisture control

Fig. 7

Moisture Refill/

Control Clean

Knob

Power

Light Humidistat

(Illuminated) Knob

Continuous Mode - Your unit will run continuously at your selected output level until you shut it off or it runs out of water.

A D V A N C E D M I S T ™ H U M I D I S T A T

The Advanced MistHumidistat allows you to adjust and select the

Fig. 8

humidity level to your personal preference. Your humidifier will turn on and off throughout the day and night to maintain the desired humidity level you have selected.

H O W T O S E T T H E H U M I D I S T A T

First, turn the Humidifier on and select your moisture/output level. Set the Advanced MistHumidistat on HIGH by turning the knob clockwise to the end (Fig. 7).

Let the humidifier run on high for a least one hour or until your room has reached a comfortable humidity level.

At this point, slowly turn your Humidistat knob counter-clockwise until the humidifier shuts off (Fig. 8).

Now that your Humidistat knob is set, the humidifier will automatically turn back on when your room drops below your comfort setting and will automatically turn off again when the setting is reached.

NOTE: If the humidifier will not start or restart when you select a moisture level, the Advanced MistHumidistat may be set too low. Turn the dial clockwise to the end (Fig. 7).

R E F I L L / C L E A N H U M I D I F I E R

When the Refill/Clean indicator light is illuminated it implies your unit

Fig. 9

 

is out of water or you need to clean your humidifier (Fig. 9).

 

Refill/Clean Light

Check your water level. If your Tank is empty, turn your Power knob

(Illuminated)

 

 

to the OFF position, remove the Tank and refill it as described in the

 

 

FILLING section.

 

If your water level is full, this implies it’s time to clean your

 

 

humidifier. Please turn off and unplug the unit and refer to the

 

 

CLEANING section.

 

NOTE: Your unit’s performance will decrease if you do not clean your heating plate. Your unit may continuously shut off and output will decrease.

NOTE: Do not turn on the unit until the tank is refilled and reinstalled.

6

Fig. 10

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 7

Manual Control Operation (HWM-331)

NOTE: This product is equipped with a Vapor Mist Sensor Badge

(Fig 10). When the Vapor Mist Sensor Badge located on the medicine cup, turns from grey to blue warm moisture

is being emitted from the humidifier. Do not touch the medicine cup or warm moisture outlet grille unless the unit has been turned off and the Vapor Mist Sensor Badge has turned back to grey.

EasySetControl Operation (Model HWM-335)

P O W E R

 

CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH

Fig. 11

 

 

 

 

 

WET HANDS AS AN ELECTRICAL SHOCK COULD

Humidistat

Moisture

 

OCCUR.

Control

 

Control

 

 

With the power OFF, plug the filled humidifier into a polarized 120V

Refill/

 

 

outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it

 

 

Clean

 

 

will only fit one way.

 

 

Light

 

S T E P 1 : P O W E R

Power

Reset

Button

Button

 

 

Press the Power button to start the humidifier. Your humidifier will

(On/Off)

 

 

 

 

automatically start on High power, continuous run (Fig. 11).

 

 

To turn your humidifier OFF simply press the Power button again.

Fig. 12

 

S T E P 2 : O U T P U T / M O I S T U R E C O N T R O L

 

 

 

Your unit has three output/moisture levels:

 

 

 

HIGH: For fast humidifying

 

 

 

MED: For everyday moisture control

 

 

 

LOW: For minimum operation (ideal for nighttime use)

 

 

• Push the Up button (+) to increase output level and push the Down button (-) to decrease output level. The LED's will illuminate to reflect which level you have selected (Fig. 12).

Continuous Mode: Your unit will run continuously at your selected output level until you shut it off or it runs out of water.

Fig. 13

S T E P 3 : S E T H U M I D I T Y

• Set your desired humidity anywhere between 35% and 55%.

• Push the Up button (+) to increase desired humidity and push the Down button (-) to decrease desired humidity. The LED's will illuminate to reflect which desired humidity level you have selected (Fig. 13).

For example: If you set your humidity at 40%, the 35% and 40%

LED’s will be illuminated.

Once you have set your desired humidity, the unit will operate under this desired setting until the unit is turned off.

When the desired room humidity has been reached the unit will automatically shut off. (The humidity LED's will remain illuminated.)

Your unit will turn back on when your room decreases beyond your set level.

NOTE: Your room humidity can often fluctuate. It is normal for your unit to turn itself on and off throughout the day as it is monitoring your changing environment.

To go back to Continuous Mode, turn your unit off and then back on and select your desired output setting (see Step 2).

7

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 8

EasySetControl Operation (Model HWM-335) cont’d.

R E F I L L / C L E A N I N D I C A T O R

Fig. 14

When the Refill/Clean indicator light is illuminated it implies your unit is out of water or you need to clean your humidifier (Fig. 14).

Check your water level. If the Tank is empty, remove the Tank and refill it

 

 

 

as described in the FILLING section.

 

 

Press the Reset button to restart the humidifier after the Tank is

 

 

 

reinstalled.

Refill/Clean

Reset

The humidifier will then resume to its previous settings.

Light

Button

(illuminated)

 

If the water level is full, this implies it’s time to clean your

humidifier. Please turn off and unplug the unit and refer to the CLEANING section.

NOTE: Do not press the Reset button until the Tank is refilled and reinstalled.

NOTE: Your unit’s performance will decrease if you do not clean your Heating Plate. You unit may continuously shut off and output will decrease.

Digital EasySetControl Operation (Model HWM-450)

P O W E R

CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH

WET HANDS AS AN ELECTRICAL SHOCK COULD

OCCUR.

With the power OFF, plug the filled humidifier into a polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way.

S T E P 1 : P O W E R

Press the Power button to start the humidifier. Your humidifier will automatically start on High power, continuous run. The display will be illuminated and will reflect the current room humidity (Fig. 15).

To turn your humidifier OFF simply press the Power button again.

S T E P 2 : O U T P U T / M O I S T U R E C O N T R O L

Your unit has three output/moisture levels:

HIGH: For fast humidifying

MED: For everyday moisture control

LOW: For minimum operation (ideal for nighttime use)

To change your moisture level, press the moisture control button ( ) up or down (Fig. 16).

Fig. 15

Desired

Timer

Control

Humidity

 

Light

Humidistat

Moisture

Control

Control

 

Refill/Clean

Reset

Light

Power Button

Button

 

(On/Off)

 

Fig. 16

Reset

Button

Once you have selected your moisture level the display will go back to showing the current room humidity after 3 seconds.

NOTE: If you wish to change or check your output/moisture setting simply press the Moisture Control button once and it will show you your setting. If you would like to change it, continue to push the button up or down until you have reached your desired setting. Again, after 3 seconds the display will revert to showing the current room humidity.

Continuous Mode: Your unit will run continuously at your selected output level until you shut it off or it runs out of water.

S T E P 3 : T I M E R C O N T R O L

You can set your Timer for up to 18 hours. This function should only be used if you desire that the humidifier be automatically shut off after a certain period of time.

8

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 9

Digital EasySetControl Operation (Model HWM-450) cont’d.

• Press the Timer button ( ) up or down to set how many hours you

Fig. 17

would like the humidifier to run (Fig. 17).

 

• When the display indicates your desired time, wait 3 seconds.

• After 3 seconds, your desired time is set and the display will revert back to showing the current room humidity.

NOTE: If you wish to change your Timer setting or check to see how much time is left simply press the Timer button once and it will show you the time left. If you want to change the time remaining, continue to

push the button up or down until you have reached your desired time. Again, after 3 seconds the display will revert to showing the current

room humidity.

Fig. 18

S T E P 4 : S E T H U M I D I T Y

• You can set your desired humidity in 1% increments anywhere from 25% to 65%.

• To set your desired humidity, press the Humidity button ( ) up or down (Fig. 18).

• When the display indicates your desired humidity setting wait 3 seconds.

• After 3 seconds your desired humidity is set and the display will

revert back to showing the current room humidity. NOTE: If you wish to change your Humidity setting or check to see what Fig. 19

you set, simply press the Humidity button once and it will show you the set humidity. If you want to change it, continue to push the button up

or down until you have reached your new desired humidity. Again, after 3 seconds the display will revert to showing the current room humidity.

Once you have set your humidity the unit will operate under this desired setting until the unit is turned off.

• When your desired room humidity has been reached your unit will shut off and the House Icon () on the top of your display will

illuminate (Fig. 19). It will stay illuminated until your desired humidity Fig. 20 decreases at which time your unit will turn back on.

NOTE: Your room humidity can often fluctuate. It is normal for your unit to turn itself on and off throughout the day as it is monitoring your changing environment.

R E F I L L / C L E A N I N D I C A T O R

• When the Refill/Clean indicator light is illuminated it implies your unit is out of water or you need to clean your humidifier.

Check your water level. If your Tank is empty, remove the Tank and refill it as described in the FILLING section.

Press the Reset button to restart the humidifier after the Tank is reinstalled (Fig. 20).

The humidifier will then resume to its previous settings.

If your water level is full, this implies it’s time to clean your humidifier. Please turn off and unplug the unit and refer to the CLEANING section.

NOTE: Do not press the Reset button until the Tank has been refilled and reinstalled.

NOTE: Your unit’s performance will decrease if you do not clean your heating plate. Your unit may continuously shut off and output will decrease.

9

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 10

Medicine Cup

CAUTION: HOT STEAM MAY CAUSE SEVERE BURNS

Fig. 21

DO NOT TOUCH THE MEDICINE CUP UNTIL IT HAS COOLED.

Place

 

 

 

 

Soothing vapor can be distributed into the air by using the Medicine Cup

 

 

at the top of the unit. To add medicine to the Medicine Cup:

medicine

 

 

here

• Turn the humidifier OFF and wait 10 minutes for the unit to cool.

 

 

 

Remove the Medicine Cup from the unit by pulling firmly upward (Fig. 21).

Fill the cup halfway with liquid medicine. Only place the medicine in the small oval area. Do not put medicine in the grille area.

Carefully reinstall the Medicine Cup back into the unit.

After use, remove and clean the Medicine Cup with warm water. Reinstall the clean and dry Medicine Cup into the unit.

WARNING: DO NOT use any liquid medicines other than those specifically recommended for use with steam vaporizers or warm HUMIDIFIERS. DO NOT pour medicine through the front or side grilles or add it to the water tank.

Kaz assumes no responsibility for consequences resulting from the use of medicine in this humidifier.

Weekly Cleaning

CAUTION: DO NOT CLEAN THE HUMIDIFIER WITH THE POWER CORD PLUGGED IN THE ELECTRICAL OUTLET AS AN ELECTRICAL SHOCK COULD OCCUR.

We recommend cleaning the humidifier once a week. It may require cleaning more often if you have hard water, notice a build up of impurities or detect unpleasant odors. The importance of routine cleaning and care cannot be over emphasized.

Cleaning involves two steps: SCALE REMOVAL and DISINFECTING. Be sure to perform these in the proper order to avoid harmful chemical interactions.

Fig. 22

Power

 

Unit

Base

• First, turn off and unplug the humidifier. Wait at least 10-15 minutes for the unit to cool.

Remove the Water Tank.

Fig. 23

To remove the Power Unit, grasp the Power Unit and lightly tilt

Removable

Water Tray

 

forward while pulling up. You will feel the unit disengage from its lock

 

 

 

(Fig. 22). Set the Power Unit aside.

 

Remove the Water Tray (Fig. 23) and set aside. Be sure to

Base

 

 

thoroughly clean the Water Reservoir in the Base. Minerals often

 

 

accumulate in this area, so special attention should be used.

 

Empty any water from the Base and Removable Tray.

 

Be sure the Heating Plate has cooled sufficiently.

Mineral Reservoir

 

 

Remove the Mineral Absorption Pad using tweezers or tongs and

check the condition of the Mineral Absorption Pad and the Heating Plate found on the Base. If build-up of minerals is heavy, follow the Cleaning the Heating Plate instructions.

CAUTION: DO NOT SUBMERGE THE BASE IN WATER. DOING SO MAY CAUSE PROPERTY DAMAGE OR PERSONAL INJURY. ALLOW THE HUMIDIFIER TO DRY COMPLETELY BEFORE PLUGGING INTO POWER OUTLET.

10

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 11

Weekly Cleaning cont’d.

STEP ONE:

SCALE REMOVAL

Removable Tray

1.Fill the Removable Water Tray (Fig. 3) with:

• 1 cup (8 oz.) of undiluted white vinegar

2.Let solution stand for 20 minutes.

3.With the vinegar in the Removable Tray, clean all interior surfaces with a soft cloth or brush to help remove scales.

4.Rinse the Removable Tray thoroughly with water to remove scale and cleaning solution.

STEP TWO:

DISINFECTING

Water Tank/Removable Tray

1.Fill the Water Tank with:

1 teaspoon of household bleach and

1 gallon of water

Pour some of this solution into the

Removable Tray.

2.Let solution stand for 20 minutes.

3.Rinse with water until the smell of bleach is gone.

NOTE: Removable Water Tray and Medicine Cup are top shelf dishwasher safe.

NOTE: THE USE OF OTHER WATER TREATMENT PRODUCTS, CHEMICALS, SOAPS, DETERGENTS OR ABRASIVE CLEANSERS NOT RECOMMENDED IN THIS MANUAL MAY CAUSE DAMAGE TO THE HUMIDIFIER OR AFFECT PERFORMANCE.

Cleaning the Heating Plate

CAUTION: HOT SURFACES MAY CAUSE SEVERE BURNS. DO NOT TOUCH ANY SURFACES UNTIL THEY HAVE COOLED.

CAUTION: DO NOT CLEAN THE HUMIDIFIER WITH THE POWER CORD PLUGGED IN THE ELECTRICAL OUTLET AS AN ELECTRICAL SHOCK COULD OCCUR.

If the output drops, or the Refill/Clean light remains on, even while there is water in the tank, the mineral build-up may need to be removed from the Heating Plate and the Mineral Reservoir. You may also have to replace the Mineral Absorption Pad.

Fig. 24

Heating

Plate

Mineral

Mineral

Absorption Pad

Reservoir

How often you perform this special maintenance depends upon the

hardness of the water you are using and how quickly mineral deposits form on the interior surfaces of the humidifier.

1.Turn off and unplug the humidifier. Allow at least 15 minutes for the unit to cool.

2.The Heating Plate is on the bottom of the Base. To access it, grasp the Power Unit and lightly tilt it forward while pulling up. You will feel the unit disengage from its lock (Fig. 22). Set the Power Unit aside.

3.Remove the Water Tray and set aside (Fig. 23).

4.Remove the Mineral Absorption Pad using tweezers or tongs to prevent burns.

5.BE SURE THE HEATING PLATE HAS COOLED SUFFICIENTLY. Empty any water from the base and remove mineral debris from the Mineral Reservoir. Be sure to clean the Mineral Reservoir thoroughly.

11

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 12

Cleaning the Heating Plate cont’d.

6.Use a non-metallic brush or soft, dry cloth to wipe the Heating Plate (Fig. 24). The Heating Plate is made of stainless steel so be sure to use non-abrasives. Some deposits may remain, but should not interfere with the operation of the unit.

CAUTION: DO NOT CLEAN THE HEATING PLATE UNDER RUNNING WATER.

DOING SO MAY CAUSE PROPERTY DAMAGE OR PERSONAL INJURY.

End-of-Season Care and Storage

Follow the CLEANING instructions when the humidifier will not be used for at least one week or more, or at the end of the season.

Dry the humidifier completely before storing. DO NOT store with water inside the Removable Tray, Base or Water Tank.

Pack the unit in its original carton and store in a cool, dry location.

Before next use, remember to clean your humidifier.

Consumer Relations

Mail questions or comments to:

Kaz, Inc.

Consumer Relations Dept. 250 Turnpike Road Southborough, MA 01772

Replacement Mineral Absorption Pads

Please be sure to specify model number.

Call us toll-free at: 1-800-477-0457 E-mail: consumerrelations@kaz.com

Or, visit our website at: www.kaz.com

Mineral Absorption Pads:

Model Number HMP-12P

Electrical Ratings

The Honeywell QuickSteam™ Series models are rated at 120V, 60 Hz.

NOTE: DO NOT RETURN PRODUCT TO STORE. IF YOU EXPERIENCE A PROBLEM, PLEASE CALL US TOLL-FREE AT 1-800-477-0457. OUR CONSUMER RELATIONS TEAM WILL HELP AND ADVISE NEXT STEPS.

CAUTION: DO NOT OPEN THE POWER UNIT OR BASE YOURSELF.

DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO

THE HUMIDIFIER OR PERSONAL INJURY.

12

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 13

Troubleshooting

Problem

Possible Cause

Corrective Action

Power

 

 

 

 

 

 

Unit is not running,

Unit needs cleaning

Clean the unit (Heating Plate, Mineral Ditch, etc.) and

some lights are on

 

change Mineral Absorption Pad as needed

 

 

 

 

 

 

Unit is out of water

Refill and reinstall Water Tank

 

 

 

 

 

 

Humidity level set too low

Reset humidity to a higher level

 

 

 

 

 

 

Unit is too hot

Turn off the power and let the unit cool down

 

 

 

 

 

 

Power Unit is not installed

Reinstall Power Unit

 

 

properly

 

 

 

 

 

 

 

Unit is not set on level

Place the unit on a firm, flat, and level surface

 

 

surface

 

 

 

 

 

 

 

There is too much moisture

Turn off the power and completely dry out the unit

 

 

inside the unit

 

 

 

 

Unit is not running, no lights

Unit is off due to timer

Press Power button

 

 

 

 

 

 

Power unit is not

Reinstall Power unit

 

 

installed properly

 

 

 

 

 

 

 

Power outage

Press Power button

 

 

 

Humidity level was set but

Humidity level set too low

Reset humidity to a higher level

unit does not start

 

 

 

 

 

Humidity level was set but

Humidity level set too high

Reset humidity to a lower level

unit does not shut off

 

 

 

 

 

Tripping the circuit breaker

Too many appliances

Remove excessive appliance(s) or place the

 

 

plugged in the same circuit

humidifier in a different circuit

Light flickering

Electrical interference

Place the humidifier in a different circuit (power outlet)

 

 

 

Sound

 

 

 

 

 

Crackling, popping sound

Unit needs cleaning

Clean the unit (Heating Plate, Mineral Reservoir, etc.)

 

 

 

and change Mineral Absorption Pad as needed

 

 

 

Gurgling sound

Unit is operating normally

None needed

 

 

 

There is no difference in

Unit is operating normally

None needed

sound between the high

 

 

and low setting

 

 

 

 

 

Humidity Display

 

 

 

 

 

Humidity display is too high

Moisture/condensation

Turn off the power and completely dry out the unit

 

 

accumulated in humidity sensor

 

 

 

 

 

 

 

Unit is overfilled with water

Drain the excess water from the base and completely

 

 

 

dry out the unit

 

 

 

Humidity display is too low

Unit is too hot

Turn off the power and let the unit cool down

 

 

 

Condensation

 

 

 

 

 

Condensation forming

Humidity level set too high

Reset humidity to a lower level and/or reduce the

on the walls and/or windows

 

Output level

 

 

 

 

 

 

Unit is placed too close to

Relocate the unit

 

 

the wall and/or windows

 

 

 

 

Steam/condensation

Unit is overfilled with water

Drain the excess water from the base and completely

coming out of the front grill

 

dry out the unit

13

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 14

3 Year Limited Warranty

You should first read all instructions before attempting to use this product.

A. This 3 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under

this warranty.

KAZ IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B.At its option, Kaz will repair or replace this product if it is found to be defective in material or workmanship. Defective product should be returned to the place of purchase in accordance with store policy. Thereafter, while within the warranty period defective product may be returned to Kaz.

C.This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.

D.Return defective product to Kaz, Inc. with a brief description of the problem. Include proof of purchase and a $10 US/$15.50 CAN check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number. You must prepay shipping charges. Send to:

In U.S.A.:

Kaz, Inc.

Attn: Returns Department

4755 Southpoint Drive

Memphis, TN 38118

USA

In Canada:

Kaz, Inc.

Attn: Returns Department

510 Bronte Street South

Milton, ON L9T 2X6

Canada

©2006 Kaz, Inc. All Rights Reserved.

P/N: 31IM0330195

14

Loading...
+ 30 hidden pages