Hobart M802, V1401 User Manual

Name: Hobart M802
Brand: Hobart
SKU: 890429
Rating: 4.3 (6 reviews)

4.3 (6)

V1401 MIXER

M802 & V1401 MIXERS

MODELS

M802 ML - 104687, 104694, 104695, 104696

V1401 ML - 104674, 104681, 104683, 104686

701 S. RIDGE AVENUE TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

FORM 33785 Rev. B (June 2001)

Model M802 Mixer

Model V1401 Mixer

– 2 –

23456789012345678901234567890121234567890

23456789012345678901234567890121234567892345678901234567890123456789012123456789Installation, Operation00 and Care of

2345678901234567890123456789012123456789 0

2345678901234567890123456789012123456789M802 and0 V1401 MIXERS

2345678901234567890123456789012123456789 0

2345678901234567890123456789012123456789SAVE THESE0 INSTRUCTIONS

2345678901234567890123456789012123456789 0

1234567890123456789012345678901212345678901234567890123456789012123456789012

23456789012345678901234567890121234567890123456789012345678901212345678901

23456789012345678901234567890121234567890123456789012345678901212345678901GENERAL

23456789012345678901234567890121234567890123456789012345678901212345678901

The23456789012345678901234567890121234567890123456789012345678901212345678901M802 model mixer is a heavy duty 80 quart mixer with a 3 horsepower motor and an electro-

234567890123456789012345678901223456789012345678901234567890121234567890123456789012345678901212345678901

123456789012345678901234567890121234567890123456789012345678901212345678901

mechanical timer123456789012345678901234567890121234567890123456789012345678901212345678901as standard equipment. Other standard features include a clutch and power bowl

123456789012345678901234567890121234567890123456789012345678901212345678901

lift. With the1use2345678901234567890123456789012123456789012of bowl adapters and special agitators, 30,45678901234567890121234567890140 or 60 quart bowls may be used on the

123456789012345678901234567890121234567890123456789012345678901212345678901

123456789012345678901234567890121234567890123456789012345678901212345678901 M802. This 123456789012345678901234567890mixer is also available with a 14"21234567890123456789012345678901212345678901higher than standard pedestal.

123456789012345678901234567890121234567890123456789012345678901212345678901

The V1401 model123456789012345678901234567890121234567890123456789012345678901212345678901mixer is a heavy duty 140 quart mixer with a 5 horsepower motor and an electro-

123456789012345678901234567890121234567890123456789012345678901212345678901

mechanical timer123456789012345678901234567890121234567890123456789012345678901212345678901as standard equipment. Other standard features include a clutch and power bowl lift. With the use of bowl adapters and special agitators, 30, 40, 60, 80 or 100 quart bowls may be used on the V1401. This mixer is also available with a 17" higher than standard pedestal.

Bowl Guard is standard equipment on all M802 and V1401 models.

Programmable Timer Controller is optional on M802 and V1401 models.

These mixers can be ordered with deluxe finish, which includes chrome plated transmission case, base, bowl support, and pedestal.

A variety of attachments and accessories are available for all mixers. These are described in a separate Use and Applications Handbook which is furnished with each mixer.

– 3 –

INSTALLATION

UNPACKING

Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery.

Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate.

LOCATION

Place the mixer in its operating location. There should be adequate space around the mixer for the user to operate the controls and install and remove bowls. The area above the mixer should allow the top cover to be removed for routine maintenance and servicing.

Holes are provided in the base for permanent bolting to the floor, although this is not necessary in normal installations. Four plastic plugs are supplied with the mixer to plug these holes if they are not used.

Once located, the mixer must be leveled.

Remove the top cover screws and the top cover.

Place a level on the machined surface of the transmission case (Fig. 1) and slide shims under the legs (base) of the mixer as required to level it front-to-back and side-to-side.

Do not replace the top cover until installation is completed.

Fig. 1

Check Lubrication Before Use

This mixer is shipped with oil in the transmission and planetary. Check oil levels before starting mixer. Refer to LUBRICATION, pages 13 – 14, for applicable lubrication procedures.

– 4 –

ELECTRICAL CONNECTIONS

WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.

WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.

A junction box with threaded hole for 3⁄4" trade size conduit is located at the top of the pedestal. Make electrical connections per the wiring diagram located on the inside of the Top Cover.

Check Rotation (Three-Phase Machines Only)

Three-phase machines must be connected so the planetary rotates in the direction of the arrow on the Drip Cup. To check rotation:

Set the gear shift lever on 1.

Apply power to the mixer, set the Electro-Mechanical Timer on HOLD; or, if equipped with a Programmable Timer Controller, set it on [ -- : -- ]. Place the Bowl Support all the way up. Set the speed on 1. Position the clutch on RUN. Momentarily run the machine by pushing the START and then STOP buttons.

If rotation is incorrect, DISCONNECT ELECTRICAL POWER SUPPLY and interchange any two of the incoming power supply leads.

– 5 –

+ 11 hidden pages