PROJECTION COLOR TV
Operating Guide for 51F710, 57F710, 65F710, 51F710S, 57F710S, 65F710S
IMPORTANT SAFETY INSTRUCTIONS ................................................................................ |
2-3 |
FIRST TIME USE .................................................................................................................. |
4-19 |
THE REMOTE CONTROL .................................................................................................. |
20-32 |
ON-SCREEN DISPLAY........................................................................................................ |
33-64 |
CARE OF YOUR HITACHI TV AND REMOTE CONTROL ........................................................ |
65 |
RECEPTION PROBLEMS.......................................................................................................... |
66 |
USEFUL INFORMATION .................................................................................................... |
67-70 |
57” / 65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS .................................................... |
71-76 |
INDEX ........................................................................................................................................ |
77 |
END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE.............................. |
78-79 |
As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
IMPORTANT SAFETY INSTRUCTIONS
SAFETY POINTS YOU SHOULD KNOW ABOUT
YOUR HITACHI TELEVISION
Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions.
Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.
Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model.
Follow all warnings and instructions marked on this television.
CAUTION |
RISK OF ELECTRIC SHOCK |
DO NOT OPEN |
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, |
DO NOT REMOVE COVER (OR BACK). |
NO USER SERVICEABLE PARTS INSIDE. |
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. |
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
•THE TELEVISION SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE TELEVISION.
NOTE: • There are no user serviceable parts inside the television.
• Model and serial numbers are indicated on back side of the television.
CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user’s authority to operate the television.
MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the user’s authority to operate the equipment.
POWER SOURCE
THIS TELEVISION IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, AC CURRENT. INSERT THE POWER CORD INTO A 120 VOLT 60Hz OUTLET.
TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION’S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NEVER CONNECT THE TELEVISION TO 50Hz, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE.
NOTE: This television receiver will display television closed captioning, ( or ), in accordance with paragraph 15.119 and 15.122 of the FCC rules.
CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other hazards. If the television does not operate properly, unplug the television and call your authorized dealer or service center.
2
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
Follow all warnings and instructions marked on this television.
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with a dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or ground- ing-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.Only use the attachments/accessories specified by the manufacturer.
12. |
Use only with the cart, stand, tripod, brack- |
|
et, or table specified by the manufacturer, or |
|
sold with the apparatus. When a cart is |
|
used, use caution when moving the |
|
cart/apparatus combination to avoid injury |
|
from tip-over. |
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.Televisions are designed to comply with the recommended safety standards for tilt and stability.
Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury.
16.Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
17.An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.
18.If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding
electrode.
Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
•This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A CableCARD provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator’s enhanced program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable company.
•Do not place any objects on the top of the television which may fall or cause a child to climb to retrieve the objects.
•Projection TV’s are heavy and can mark or damage floor surfaces (especially wood flooring) if moved improperly. Do not slide or force TV into position. Always roll TV allowing casters at bottom of unit to help steer and position the TV.
•PREVENTION OF SCREEN BURN
This Wide Screen TV is designed to display wide screen pictures. Images should be viewed mostly in wide screen format or zoomed to fit the screen with moving pictures. Use of side panels, top and bottom panels of standard picture formats should only be 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the picture will age more rapidly than the gray areas. Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-moving) patterns can cause permanent damage to television receivers. Such “SCREEN BURNS” constitute misuse and are NOT COVERED by your HITACHI Factory Warranty.
•PUBLIC VIEWING OF COPYRIGHTED MATERIAL
Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.
•This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
This product contains lead. Dispose of this product in accordance with applicable environmental laws. For product recycling and disposal information, contact your local government agency or the Electronic Industries Alliance at www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada). For more information, call 1-800-HITACHI.
3
ACCESSORIES
Check to make sure you have the following accessories before disposing of the packing material.
TIME USE |
REMOTE CONTROL |
BATTERIES |
“Z” ALLEN KEY |
|
|
(“AA”) |
|
||
|
|
|
||
FIRST |
|
2. |
For 57” and 65” Models Only |
|
|
3. |
|||
OPTIONAL TV TOP SHELF (NOT INCLUDED, ORDER SEPARATELY) |
||||
|
||||
|
Model No. Part No. |
|
||
|
SLF10 |
QJ01611 |
|
|
|
1. |
|
|
CAUTION: This SLF10 TV Top Shelf for use only with Hitachi 51F710, 51F710S and 57F710, 57F710S. Use with other apparatus is capable of resulting in instability causing possible injury.
1.Remote Control Unit CLU-4341UG2 (Part No. HL02071) or CLU4351UG2 (Part No. HL02072).
2.Two “AA” size, 1.5V batteries (For Remote Control Unit).
3.“Z” Allen Key (Part No. 61010122).
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT
1.Open the battery cover of the remote control by pushing down and sliding the back cover off.
2.Insert two new “AA” size batteries for the remote control. When replacing old batteries, push them towards the springs and lift them out.
3.Match the batteries to the (+) and (-) marks in the battery compartment.
4.Replace the cover.
BOTTOM VIEW
(Remote Control)
Lift up on tab to remove back cover.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.
4
HOW TO SET UP YOUR NEW HITACHI PROJECTION TV
ANTENNA
Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set.
To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
NOTE: Your new HDTV has a built-in high definition television signal processor. This television includes a fan to cool the processor. The sound of moving air from the fan is normal and maybe noticeable in very quiet environments.
VIEWING
The major benefit of the HITACHI Projection Television is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing.
The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as the viewer moves to the left and right of the receiver.
During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room.
If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.
USE TIME FIRST
|
|
|
|
|
R |
|
20' |
|
S |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4" Minimum |
50 |
BEST |
|
|
|
|
|
|
|
|
|
HORIZONTAL |
|
|
|
|
|
BEST |
|
|
|
|
|
|
|
|
|
VERTICAL VIEWING |
5' |
|
10' |
15' |
20' |
|
|
|
20 |
ANGLE |
|
|
||||
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
50 |
VIEWING ANGLE |
|
|
|
3’ |
|
|
|
4" Minimum |
|
|
|
|
|
|
|
|
|
|
|
|
||
0’ |
5’ |
10’ |
15’ |
20’ |
L |
|
|
|
S |
|
|
|
|
|
|
|
|
CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too close to the television. Move the magnetic field source away from the television until there is no picture distortion.
5
HOOK-UP CABLES AND CONNECTORS
FIRST TIME USE
Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.
300-Ohm Twin Lead Connector
This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm).
Phono Connector
Used on all standard video and audio cables which connect to inputs and outputs located on the television’s rear jack panel and front control panel.
“F”Type 75-Ohm Coaxial Antenna Connector
For connecting RF signals (antenna or cable TV) to the antenna jack on the television.
Optical Cable
This cable is used to connect to an audio amplifier with an Optical Audio In jack. Use this cable for the best sound quality.
1 6 2 7 3 8 4 9 5
D-SUB MINI 9-Pin Cable
This cable is used to connect to the RS232C input located on the rear panel so you can control some of your TV functions from an external home control system.
HDMI Cable
S-Video (Super Video) Connector |
This cable is used to connect your external devices such as Set- |
This connector is used on camcorders, VCRs and laserdisc |
Top-Boxes or DVD players equipped with an HDMI output con- |
players with an S-Video feature in place of the |
nection to the TV’s HDMI input. |
standard video cable to produce a high quality picture. |
|
ANTENNA CONNECTIONS TO REAR JACK PANEL
VHF (75-Ohm) antenna/CATV (Cable TV)
When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the ANT A (75-Ohm) terminal. If you have an antenna, connect the coaxial cable to the ANT B terminal.
To outdoor antenna or CATV cable
To antenna
To outdoor VHF or UHF antenna
VHF (300-Ohm) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV.
From UHF antenna
When both VHF and UHF antennas are connected
Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer.
ANT A |
From outdoor |
|
antenna or |
|
CATV System |
Antenna Mixer
6
FRONT PANEL CONTROLS
h
i
e
USE TIME FIRST
INPUT 5 |
MAGIC |
AUDIO |
|
VOL- |
VOL+ |
CH- |
CH+ |
INPUT |
MENU |
FOCUS |
S-VIDEO VIDEO L/MONO |
R |
F |
E |
H |
G |
EXIT |
SELECT |
|
|
|
|
|
|
|
|
||
|
|
|
CURSOR |
|
|
|
|
|
|
|
e |
d |
|
c |
b a |
f |
|
g |
|
|
|
|
|
|||
|
|
|
|
|
|
aMENU/SELECT button
This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.
bINPUT/EXIT button
Press this button to display the input menu, Ant A/B, INPUT:1,2,3,4 and 5. This button also serves as the EXIT button when in MENU mode.
cCHANNEL selector
Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down (H) and up (G) buttons when in MENU mode.
dVOLUME level
Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left (F) and right (E) buttons when in MENU mode. When the TV power is turned OFF at a volume level 31 or greater, the volume level will default to 30 when the TV is turned ON. However, if it is set to a level 30 or less, the volume level will be at the level it was set when the TV is turned ON.
ePOWER button/ POWER LED
Press this button to turn the TV on or off. This LED light is on during normal operation. At initial TV Turn “ON”, the Power button LED will blink several times before a channel can be tuned and viewed. This is a normal default operation of this television. The blinking time of the Power button LED varies depending on the period of time between when you turn “ON” and when you turn “OFF” the TV. This default operation is an energy saving feature. You can choose not to use this feature by selecting “On” for the “Quick Start Up” option in the On-Screen-Display Menu. Select “Setup” in the On-Screen-Display Menu, then select “Quick Start Up”. Select the “On” feature to quickly tune and view channels at initial TV Turn “ON” (see page 64).
fMAGIC FOCUS
Use this button to automatically adjust your picture quality to optimum performance (see page 55).
gFRONT INPUT JACKS (INPUT 5)
Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording. Press the INPUT button and select Input 5. If you have mono sound, insert the audio cable into the left audio jack.
hIR RECEIVER Sensor (1)
The screen area acts as one of the IR receivers (remote sensor) of the TV. When using the remote control, point it towards the screen for best response.
iIR RECEIVER Sensor (2)
This is an additional remote sensor for a better remote control range of response.
7
FRONT PANEL JACKS AND CONNECTORS
FIRST TIME USE
The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples:
INPUT 5 |
INPUT 5 |
AUDIO |
AUDIO |
S-VIDEO VIDEO L/MONO R |
S-VIDEO VIDEO L/MONO R |
NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal.
2.If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.
3.If you have a mono VCR, insert the audio cable into the left audio jack of your TV.
8
REAR PANEL JACKS
ae
ANT A
HDMI 1
|
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
|
Y/ |
Y/ |
|
|
|
|
|
||
c |
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
||||
|
S-VIDEO |
|
|
|
|
|
|
|
|
PB |
PB |
d |
|
|
|
PR |
PR |
|
VIDEO |
|
|
|
|
|
|
(MONO) |
(MONO) |
(MONO) |
(MONO) |
|
L |
|
|
|
|
|
AUDIO |
|
TV AS CENTER |
|
|
|
R |
|
|
|
|
|
AUDIO |
|
|
|
|
|
TO HI-FI |
|
|
|
|
b jf
CableCARD
(Top of card faces right)
OPTICAL OUT
Digital Audio
Upgrade Card
Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; and 6,381,747 licensed for limited viewing uses only.
RS232C
1 2 3 4 5
6 7 8 9
i
k
g h
aAntenna Input
ANT A- A 75-Ohm RF antenna or CATV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture. ANT B- A 75-Ohm RF antenna input. ANT B can only be displayed as a main picture. ANT B cannot be displayed as a
sub-picture.
NOTE: You may ask your local cable company whether DTV services are available.
bAudio/Video Inputs 1, 2, 3 and 4
By using the INPUTS button, CURSOR buttons and SELECT button of the remote control you can select each video source. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the left audio jack.)
USE TIME FIRST
NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a time.
cMONITOR OUT
These jacks provide fixed or variable audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video output (see page 63).
dS-VIDEO Inputs 3 and 4
Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.
eComponent: Y-PBPR Inputs
Inputs 1 and 2 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use composite video signal for both inputs.
NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority over VIDEO input.
2.Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s PR input.
3.Your component outputs may be labeled Y-CBCR. In this case, connect the component CB output to the TV’s PB input and the component CR output to the TV’s PR input.
4.It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs (see page 37).
5.To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR jacks.
6.Input 1 and Input 2 (Y/VIDEO) can be used for composite video and component video input.
9
REAR PANEL JACKS
FIRST TIME USE
fHDMI1 (High Definition Multimedia Interface) (INPUT 1)
About HDMI
HDMI is the next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed high-definition video and multi-channel audio in a single cable. Because digital television (DTV) signals remain in digital format, HDMI assures that pristine high-definition images retain the highest video quality from the source all the way to your television screen.
Use the HDMI input for your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
NOTES: 1. The HDMI input is not intended for use with personal computers.
2. Only DTV formats such as 1080i, 720p, 480i and 480p are available for HDMI input.
gOptical Out (Digital Audio)
This jack provides Digital Audio Output for your audio device that is Dolby® Digital and PCM compatible, such as an audio amplifier.
NOTE: *Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
hUpgrade Card
This card slot is for future software upgrades. Hitachi will notify you if a software upgrade is required for your TV. In order to receive written notification, please complete and return your warranty card.
iRS232C Input
For use with third party home Audio/Video control systems which are commercially available. Please see your dealer regarding these “non Hitachi” home control systems (see page 64 to activate this input).
jTV AS CENTER (INPUTS 1-4)
These jacks are for stereo amplifiers with center signal output capability. This feature allows the TV speakers to be used as a center speaker. The TV must be set as a center channel by selecting “TV as Center” on the Internal Speakers Settings of the Audio Menu (see page 41).
10
REAR PANEL JACKS
kCableCARD Slot
This slot is for the CableCARD that will be provided by your local cable operator to gain access to chosen cable channels. The CableCARD will allow you to tune digital and high definition cable channels. Please call your local cable operator if this service is available before requesting a CableCARD (also known as Point of Deployment (POD) module).
Connect a coaxial cable to ANT A terminal of the Rear Panel Jacks.
Insert the CableCARD into the slot (Top of card should be facing right as shown).
Digital Cable
ANT A
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
Y/ |
Y/ |
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
|||
S-VIDEO |
|
|
|
|
|
|
|
PB |
PB |
|
|
|
PR |
PR |
VIDEO |
|
|
|
|
|
(MONO) |
(MONO) |
(MONO) |
(MONO) |
L |
|
|
|
|
AUDIO |
|
TV AS CENTER |
|
|
R |
|
|
|
|
AUDIO |
|
|
|
|
TO HI-FI |
|
|
|
|
CableCARD
(Top of card faces right)
THIS |
END |
|
|
T |
|
INSER |
|
CableCARD |
OPTICAL OUT
Digital Audio
Upgrade Card
Claims of U.S. Patent Nos. 4,577,216; 4,819,098; and 6,381,747 licensed
limited viewing uses only.
RS232C
1 2 3 4 5
6 7 8 9
USE TIME FIRST
If the CableCARD is properly installed or not installed, the TV will display the following respective screens.
|
|
|
|
|
|
|
|
CableCARD is installed |
|
OR |
|
CableCARD |
|
|
|
|
|
is not installed |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After the CableCARD is installed, wait until the second screen below appears. The third screen below will appear if a channel is not authorized for viewing. Press the EXIT button to exit the second screen.
Acquiring Data.
Please wait.
In order to start cable service for this device, please contact your cable provider
CableCARD(tm): 123-456-789-1
Host: 123-456-789-1
Data: 123-456-789-1
UnitAddress: 123-456-789-1
Not an Authorized Channel
Press EXIT to return
Please take note of all information on the screen (you will provide this information to your cable operator). Call your cable operator and give them the information from the card to start your cable service.
NOTES: 1. A digital cable subscription is required.
2.Antenna B will not be available when CableCARD is inserted.
3.Do not insert a PCMCIA card into the CableCARD slot.
11
REAR PANEL CONNECTIONS
FIRST TIME USE
Outside antenna or digital cable
TYPICAL FULL-FEATURE SETUP
DVD Player
OUTPUT
Y PB/CB PR/CR L R
|
|
|
|
|
External Digital |
|
|
|
|
|
Component with |
|
|
|
|
CableCARD |
HDMI output |
|
|
|
|
(Top of card faces right) |
capability |
|
ANT A |
|
|
|
|
|
|
|
|
|
HDMI |
|
|
|
|
|
OUT |
|
|
|
|
HDMI 1 |
|
|
ANT B |
INPUT 2 |
INPUT 1 |
|
|
|
Y/ |
Y/ |
|
|
|
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
VIDEO |
VIDEO |
|
|
INPUT 3 |
|
|
|
||
S-VIDEO |
|
|
|
|
To an amplifier/receiver |
|
|
PB |
PB |
|
with optical input capability. |
|
|
OPTICAL OUT |
|
||
|
|
|
|
Digital Audio |
|
|
|
PR |
PR |
Upgrade Card |
|
|
|
Apparatus Claims of U.S. Patent Nos. |
|
||
VIDEO |
|
|
|
|
|
|
|
|
4,631,603; 4,577,216; 4,819,098; |
|
|
|
|
|
|
4,907,093; and 6,381,747 licensed |
|
|
|
|
|
for limited viewing uses only. |
|
(MONO) |
(MONO) |
(MONO) |
(MONO) |
|
|
|
|
L |
|
|
|
|
|
|
|
AUDIO |
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|||
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
INPUT |
OUTPUT |
OUTPUT |
S-VIDEO V L R |
S-VIDEO V L R |
S-VIDEO V L R |
VCR #2 VCR #1
Laserdisc player, VCR, camcorder, etc.
NOTES: 1. Connect only 1 component to each input jack.
2.Follow connections that pertain to your personal entertainment system.
3.Inputs 1 and 2 can accomodate Composite and Component video signals.
4.Cables are not included with the purchase of this TV, except when noted as “provided”.
12
TIPS ON REAR PANEL CONNECTIONS
• S-VIDEO, Y-PbPr and HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature.
|
Use these connections in place of the standard video connection if your device has this feature. |
|
|
• If your device has only one audio output (mono sound), connect it to the left audio jack on the television. |
FIRST |
||
• Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables. |
|||
|
|||
• A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 3 in |
TIME |
||
• |
You may use VIDEO or S-VIDEO inputs to connect to Input 3, Input 4 or Input 5, but only one of these may be used at a time. |
||
|
the example on page 12). Refer to your VCR operating guide for more information on line input-output connections. |
|
|
• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack. |
USE |
||
|
|||
• COMPONENT: Y-PBPR (Input 1 & 2) connections are provided for high performance components, such as DVD players and set- |
|
||
|
top-boxes. Use these connections in place of the standard video connection if your device has this feature. Input 2 accepts |
|
|
|
both composite and component video signals. |
|
|
• |
Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input |
|
|
|
and the components R-Y output to the TV’s PR input. |
|
|
• Your component outputs may be labeled Y-CBCR. In this case, connect the components CB output to the TV’s PB input and |
|
||
|
the components CR output to the TV’s PR input. |
|
|
• You may use composite and component video signals for Inputs 1 and 2. |
|
||
• |
It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs (see page 37). |
|
•To ensure no copyright infringement, the MONITOR OUT output may be abnormal, when using the Y-PBPR jacks.
•When using an HDMI input from a Set-Top-Box, it is recommended that a 1080i or 720p input signal is used.
13
FIRST TIME USE
CONNECTING EXTERNAL AUDIO SOURCES
Match the numbers below to the diagram for speaker placement.
1 The television’s internal speakers will act as center speaker (select Audio-Internal Speakers-TV as Center). 2 These FRONT left and right speakers are connected to the FRONT output of a separate audio amplifier. 3 These REAR left and right speakers are connected to the REAR output of a separate audio amplifier.
4 This subwoofer is connected to the LFE/Sub Out output of a separate audio amplifier.
REAR PANEL OF TELEVISION
CableCARD
(Top of card faces right)
ANT A
HDMI 1
|
ANT B |
INPUT 2 |
INPUT 1 |
|
Y/ |
Y/ |
|
|
|
||
MONITOR OUT |
INPUT 4 |
VIDEO |
VIDEO |
INPUT 3 |
|
||
S-VIDEO |
|
|
|
PB |
PB |
|
OPTICAL OUT |
|
Digital Audio |
Upgrade Card
PR PR
Apparatus Claims of U.S. Patent Nos. VIDEO 4,631,603; 4,577,216; 4,819,098;
4,907,093; and 6,381,747 licensed for limited viewing uses only.
(MONO) |
(MONO) |
(MONO) |
(MONO) |
|
|
|
|
|
L |
|
|
|
|
|
|
|
|
AUDIO |
TV AS CENTER |
|
RS232C |
|||||
|
|
|
|
|||||
R |
|
|
|
1 |
2 |
3 |
4 |
5 |
|
|
|
|
6 |
7 |
8 |
9 |
|
AUDIO |
|
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
|
|
|
|
CENTER |
OPTICAL |
|
|
|
|
|
|
|
OUT |
INPUT |
|
|
|
|
Stereo System Amplifier
or DVD Player
NOTES: 1. The Optical Out (Digital Audio) provides a fixed digital audio output to your external component such as an A/V receiver with optical input capability. The audio level can only be controlled through the volume control of the external audio amplifier.
2.See page 42 for AUDIO-Digital Output.
14
CONNECTING EXTERNAL VIDEO SOURCES
The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.
Before Operating External Video Source
Connect an external source to the INPUT terminal, then press the INPUTS button to show the INPUTS menu. Use the CURSOR PAD to select the Antenna and Input of your choice. Then press the SELECT button to confirm your choice (see page 24).
Input 5
Ant B
Ant A
Input 1
Input 2
Move SEL Sel
USE TIME FIRST
NOTE: When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the back panel
of the TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the set will appear to be OFF.
CONNECTING A MONAURAL AUDIO SOURCE TO INPUT1~INPUT5
1.Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below.
2.Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.
3.Press the INPUTS button, then select INPUT 1 from the INPUTS menu to view the program from the VCR or the laserdisc player. The VIDEO OSD label disappears automatically after approximately four seconds.
4.Select Antenna from the INPUTS menu to return to the previous channel.
CableCARD
(Top of card faces right)
ANT A
HDMI 1
|
ANT B |
INPUT 2 |
INPUT 1 |
|
Y/ |
Y/ |
|
|
|
||
MONITOR OUT |
INPUT 4 |
VIDEO |
VIDEO |
INPUT 3 |
|
||
S-VIDEO |
|
|
|
PB |
PB |
|
OPTICAL OUT |
|
Digital Audio |
Upgrade Card
PR PR
Apparatus Claims of U.S. Patent Nos. VIDEO 4,631,603; 4,577,216; 4,819,098;
4,907,093; and 6,381,747 licensed for limited viewing uses only.
(MONO) |
(MONO) |
(MONO) |
(MONO) |
|
|
|
|
L |
|
|
|
|
|
|
|
AUDIO |
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|||
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
Audio Video
OUTPUT
VCR
15
|
|
|
|
CONNECTING EXTERNAL VIDEO SOURCES |
|
|
|
|
|||
|
|
|
|
||
|
CONNECTING A STEREO SOURCE TO INPUT1~INPUT5 |
||||
|
1. |
Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set |
|||
USE |
|
|
below. |
||
2. |
Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. |
||||
|
|||||
TIME |
3. |
Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. |
|||
4. |
Press the INPUTS button, then select INPUT 3 from the INPUTS menu to view the program from the VCR or laserdisc player. |
||||
|
|||||
FIRST |
|
|
The VIDEO OSD label disappears automatically after approximately four seconds. |
||
5. |
Select Antenna from the INPUTS menu to return to the previous channel. |
||||
|
|
|
|
|
CableCARD |
|
|||
|
|
|
|
(Top of card faces right) |
||||
|
ANT A |
|
|
|
|
|
|
|
|
|
|
|
HDMI 1 |
|
|
|
|
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
|
|
|
|
Y/ |
Y/ |
|
|
|
|
|
|
|
|
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
|
|
|
|
|
|
|
|
|||
S-VIDEO |
|
|
|
|
|
|
|
|
|
|
|
PB |
PB |
|
|
|
|
|
|
|
|
OPTICAL OUT |
|
|
|
|
|
|
|
|
Digital Audio |
|
|
|
|
|
|
|
PR |
Upgrade Card |
|
|
||
|
|
|
PR |
|
|
|
|
|
VIDEO |
|
|
|
Apparatus Claims of U.S. Patent Nos. |
||||
|
|
|
4,631,603; 4,577,216; 4,819,098; |
|||||
|
|
|
|
4,907,093; and 6,381,747 licensed |
||||
|
(MONO) |
|
|
for limited viewing uses only. |
||||
|
(MONO) |
(MONO) |
(MONO) |
|
|
|
|
|
L |
|
|
|
|
|
|
|
|
AUDIO |
|
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|
|||
|
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
|
OUTPUT
R L V
VCR
NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.
2.A single VCR can be used for VCR #1 and VCR #2 (see page 12), but note that a VCR cannot record its own video or line output. Refer to your VCR operating guide for more information on line input-output connections.
16
CONNECTING EXTERNAL VIDEO SOURCES
CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 |
|
||
1. |
Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV |
|
|
|
set below. |
FIRST |
|
3. |
Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. |
||
2. |
Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. |
|
|
4. |
Press the INPUTS button, then select INPUT 3 from the INPUTS menu to view the program from the VCR or laserdisc player. |
TIME |
|
|
|||
|
The VIDEO OSD label disappears automatically after approximately four seconds. |
USE |
|
5. |
Select Antenna from the INPUTS menu to return to the previous channel. |
||
|
|
|
|
|
CableCARD |
|
|||
|
|
|
|
(Top of card faces right) |
||||
|
ANT A |
|
|
|
|
|
|
|
|
|
|
|
HDMI 1 |
|
|
|
|
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
|
|
|
|
Y/ |
Y/ |
|
|
|
|
|
|
|
|
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
|
|
|
|
|
|
|
|
|||
S-VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
PB |
|
|
|
|
|
|
|
|
OPTICAL OUT |
|
|
|
|
|
|
|
|
Digital Audio |
|
|
|
|
|
|
|
PR |
Upgrade Card |
|
|
||
|
|
|
PR |
|
|
|
|
|
VIDEO |
|
|
|
Apparatus Claims of U.S. Patent Nos. |
||||
|
|
|
4,631,603; 4,577,216; 4,819,098; |
|||||
|
|
|
|
4,907,093; and 6,381,747 licensed |
||||
|
(MONO) |
(MONO) |
(MONO) |
for limited viewing uses only. |
||||
|
(MONO) |
|
|
|
|
|||
L |
|
|
|
|
|
|
|
|
AUDIO |
|
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|
|||
|
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
|
R L V
S-VIDEO
VCR
NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.
2.A single VCR can be used for VCR #1 and VCR #2 (see page 12), but note that a VCR cannot record its own video or line output. Refer to your VCR operating guide for more information on line input-output connections.
17
CONNECTING EXTERNAL VIDEO SOURCES
FIRST TIME USE
CONNECTING A COMPONENT SOURCE WITH HDMI or DVI CAPABILITY TO INPUT 1
1.Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the TV set below. When using a component with DVI output, you also have to connect the AUDIO OUT (R/L) of the component to the AUDIO IN (R/L) of INPUT 1.
2.Press the INPUTS button, then select INPUT 1 from the INPUTS menu to view the program from the HDTV set top box or DVD player. The VIDEO OSD label disappears automatically after approximately four seconds.
3.Select Antenna from the INPUTS menu to return to the previous channel.
HDMI-HDMI
|
|
|
|
CableCARD |
|
|||
|
|
|
|
(Top of card faces right) |
||||
|
ANT A |
|
|
|
|
|
|
|
|
|
|
|
HDMI 1 |
|
|
|
|
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
|
|
|
|
Y/ |
Y/ |
|
|
|
|
|
|
|
|
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
|
|
|
|
|
|
|
|
|||
S-VIDEO |
|
|
|
|
|
|
|
|
|
|
|
PB |
PB |
|
|
|
|
|
|
|
|
OPTICAL OUT |
|
|
||
|
|
|
|
Digital Audio |
|
|
|
|
|
|
|
PR |
Upgrade Card |
|
|
||
|
|
|
PR |
|
|
|
|
|
VIDEO |
|
|
|
Apparatus Claims of U.S. Patent Nos. |
||||
|
|
|
4,631,603; 4,577,216; 4,819,098; |
|||||
|
|
|
|
4,907,093; and 6,381,747 licensed |
||||
|
(MONO) |
(MONO) |
(MONO) |
for limited viewing uses only. |
||||
|
(MONO) |
|
|
|
|
|||
L |
|
|
|
|
|
|
|
|
AUDIO |
|
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
|
HDMI Cable
DVI-HDMI
|
|
|
|
CableCARD |
|
|||
|
|
|
|
(Top of card faces right) |
||||
|
ANT A |
|
|
|
|
|
|
|
|
|
|
|
HDMI 1 |
|
|
|
|
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
|
|
|
|
Y/ |
Y/ |
|
|
|
|
|
|
|
|
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
|
|
|
|
|
|
|
|
|||
S-VIDEO |
|
|
|
|
|
|
|
|
|
|
|
PB |
PB |
|
|
|
|
|
|
|
|
OPTICAL OUT |
|
|
||
|
|
|
|
Digital Audio |
|
|
|
|
|
|
|
PR |
Upgrade Card |
|
|
||
|
|
|
PR |
|
|
|
|
|
VIDEO |
|
|
|
Apparatus Claims of U.S. Patent Nos. |
||||
|
|
|
4,631,603; 4,577,216; 4,819,098; |
|||||
|
|
|
|
4,907,093; and 6,381,747 licensed |
||||
|
(MONO) |
(MONO) |
(MONO) |
for limited viewing uses only. |
||||
|
(MONO) |
|
|
|
|
|||
L |
|
|
|
|
|
|
|
|
AUDIO |
|
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
|
DVI to HDMI
Cable
HDMI Output
DIGITAL OUTPUT
R L
AUDIO OUT
DVD Player or HDTV STB
DVD Player or HDTV STB
NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.
2.The HDMI input on INPUT 1 contains the copy protection system called High-bandwidth Digital Content Protection (HDCP). HDCP is a cryptographic system that encrypts video signals when using HDMI connections to prevent illegal copying of video contents.
3.HDMI is not a “NETWORK” technology. It establishes a one-way point-to-point connection for delivery of uncompressed video to a display.
4.The connected digital output device controls the HDMI interface so proper set-up of device user settings determines final video appearance.
18
CONNECTING EXTERNAL VIDEO SOURCES
CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR. |
|
||
1. |
Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV |
|
|
|
set below. |
FIRST |
|
2. |
Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. |
||
|
|||
3. |
Connect the cable from the CR/PR OUT or R-Y OUT of the laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. |
TIME |
|
4. |
Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack. |
||
USE |
|||
5. |
Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack. |
||
|
|||
6. |
Press the the INPUTS button, then select INPUT 2 from the INPUTS menu to view the program from the Laserdisc/DVD player |
|
|
|
or HDTV set top box. The VIDEO OSD label disappears automatically after approximately four seconds. |
|
|
7. |
Select Antenna from the INPUTS menu to return to the previous channel. |
|
|
|
|
|
CableCARD |
|
|||
|
|
|
|
(Top of card faces right) |
||||
|
ANT A |
|
|
|
|
|
|
|
|
|
|
|
HDMI 1 |
|
|
|
|
|
ANT B |
|
INPUT 2 |
INPUT 1 |
|
|
|
|
|
|
Y/ |
Y/ |
|
|
|
|
|
|
|
|
|
|
|
|
||
MONITOR OUT |
INPUT 4 |
INPUT 3 |
VIDEO |
VIDEO |
|
|
|
|
|
|
|
|
|
|
|||
S-VIDEO |
|
|
|
|
|
|
|
|
|
|
|
PB |
PB |
|
|
|
|
|
|
|
|
OPTICAL OUT |
|
|
||
|
|
|
|
Digital Audio |
|
|
|
|
|
|
|
PR |
Upgrade Card |
|
|
||
|
|
|
PR |
|
|
|
|
|
VIDEO |
|
|
|
Apparatus Claims of U.S. Patent Nos. |
||||
|
|
|
4,631,603; 4,577,216; 4,819,098; |
|||||
|
|
|
|
4,907,093; and 6,381,747 licensed |
||||
|
(MONO) |
(MONO) |
(MONO) |
for limited viewing uses only. |
||||
|
(MONO) |
|
|
|
|
|||
L |
|
|
|
|
|
|
|
|
AUDIO |
|
TV AS CENTER |
RS232C |
|||||
|
|
|
|
|
|
|||
|
|
|
|
1 |
2 |
3 |
4 |
5 |
R |
|
|
|
|
6 |
7 |
8 |
9 |
|
|
|
|
|
|
|
|
|
AUDIO |
|
|
|
|
|
|
|
|
TO HI-FI |
|
|
|
|
|
|
|
|
OUTPUT
R L PR PB Y
DVD Player
NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.
2. See page 13 for tips on REAR PANEL CONNECTIONS.
19
THE REMOTE CONTROL
THE REMOTE CONTROL
In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-boxes, satellite receivers (SAT) and DVD players with one touch. Basic operation keys are grouped together in one area.
To operate your TV, point the remote control at the screen of the TV and press the TV button. The remote will now control your television.
To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The remote will now control your VCR (see page 32 for instructions on how to program the remote to control your VCR).
To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The remote will now control your cable box (see page 29 for instructions on how to program the remote to control your cable box).
To operate your set-top-box or satellite receiver, point the remote at the remote sensor of the set-top-box or satellite receiver and press the SAT button. The remote will now control your set-top-box or satellite receiver. If you have a satellite receiver, use this button to program your satellite receiver (see page 30 for instructions on how to program the remote to control your SAT).
To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The remote will now control your DVD player (see page 31 for instruction on how to program the remote to control your DVD
player).
20
HOW TO USE THE REMOTE TO CONTROL YOUR TV
a b
fd
eg hj
k
n
m
i l
n
o p
q c
aPOWER button
Press this button to turn the TV set on or off when the remote is in TV mode. (See page 20 for instructions on how to set the remote control to TV mode.)
bMODE buttons
These buttons allow the remote to control your TV, VCR, DVD, Cable box/Satellite box depending on which button is pressed.
cPAUSE button
Press the PAUSE button to freeze the picture. Press the EXIT button to return the picture to motion. Press the PAUSE button repeatedly to cycle through the three different freeze modes (see page 28).
Freeze
Freeze |
Freeze |
Freeze |
Freeze
dDAY/NIGHT button
Press this button to toggle between Day and Night picture mode settings. Select Day for day time viewing with more brightness and contrast to compete with room light. Select Night for night time viewing with less brightness and contrast for a more detailed picture (see page 36 for settings changes).
21
CONTROL REMOTE THE
HOW TO USE THE REMOTE TO CONTROL YOUR TV
THE REMOTE CONTROL
eASPECT button
Press this button to quickly change the picture format ASPECT ratio.
Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options.
4:3 |
STANDARD |
Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the |
|
|
left and right of the image to preserve the original aspect ratio of the source. Note: Use this mode for |
|
|
only 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted |
|
|
area of the picture will age more rapidly than the gray areas. |
4:3 |
EXPANDED |
Use this aspect mode to display conventional (4:3) sources by linearly increasing image expansion from |
|
|
the center towards the edges of the display area in order to fill it. |
4:3 |
Zoom1/Zoom2 |
Use these aspect modes to zoom in on conventional (4:3) sources. |
16:9 STANDARD |
Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect |
|
|
|
ratio. |
16:9 Zoom |
Use this aspect to Zoom-in once while in 16:9 aspect. |
(1)NTSC/480i/480P Input
4:3 |
|
|
|
INPUT |
4:3 STANDARD |
4:3 EXPANDED |
4:3 ZOOM1 |
|
16:9 ZOOM |
16:9 STANDARD |
4:3 ZOOM2 |
(2)480i/480P Input
16:9
INPUT |
4:3 STANDARD |
4:3 EXPANDED |
4:3 ZOOM1 |
|
16:9 ZOOM |
16:9 STANDARD |
4:3 ZOOM2 |
(3)HDMI/720P/1080i Input
16:9
INPUT 16:9 STANDARD 16:9 ZOOM 4:3 EXPANDED
NOTES: 1. The Aspect Style setting you select for an ANT input will automatically be set for the other ANT input. However, all five video inputs have independent Aspect Style settings.
2.Vertical position adjustments are directly available when you choose 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM aspect style (see also page 43).
22
HOW TO USE THE REMOTE TO
CONTROL YOUR TV
fINPUTS button
When the remote control is in TV mode, press this button to access the INPUTS menu. Use the CURSOR and SELECT buttons to select the inputs that are being used. Pressing the INPUTS button repeatedly will also cycle through the Inputs menu items. Then press the SELECT button to select.
Ant B
Ant A
Input 1
Input 2
Input 3
Input 4
Input 5
Input 5
Ant B
Ant A
Input 1
Input 2
Move SEL Select
Select to choose Antenna B.
Select to choose Antenna A.
Select to choose Input 1 for Video 1.
Select to choose Input 2 for Video 2.
Select to choose Input 3 for Video 3.
Select to choose Input 4 for Video 4.
Select to choose Input 5 for Video 5.
CONTROL REMOTE THE
23
HOW TO USE THE REMOTE TO CONTROL YOUR TV
THE REMOTE CONTROL
gPICTURE-IN-PICTURE button
See separate section on pages 26-28 for a description.
hMENU button
The MENU button will start the On-Screen Display.
iGUIDE button [Cable Box (CBL), Satellite Receiver (SAT)/Set-Top-Box (STB) mode only]
The use of this button is only applicable when the remote control is in (CBL) and (SAT/STB) mode. Press this button to access the Channel Guide of the (CBL), and (SAT/STB).
jEXIT button
This button will exit all On-Screen Displays.
kCURSOR buttons/SELECT button
All the On-Screen Display features can be set or adjusted by using the CURSOR buttons and the SELECT button, except for numeric entries. Press the CURSOR buttons toward desired direction and press the SELECT button to select.
lINFO button
Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the TIMER is set.
|
ANALOG CHANNELS |
|
|
||||
|
|
|
|
|
3:32 PM |
Time |
|
|
|
|
|
|
Ant A 22 |
Main Picture Source |
|
|
|
|
|
|
ST Stereo |
Audio Broadcast |
|
|
|
|
|
|
R |
Broadcast Rating |
|
INFO |
|
|
|
|
|
|
|
|
|
|
|
|
|
Aspect |
|
|
Closed |
|
|
|
|
Mode |
|
|
|
|
|
|
|
|
|
|
Captioning |
|
|
|
|
|
|
Day/Night |
Day |
|
CC Off |
4:3 Expanded |
|
|
|
Mode |
|
|
|
||||
|
View --:-- AM --:-- PM |
|
|
|
|
||
|
Event Timer |
|
|
|
|
|
|
|
DIGITAL CHANNELS |
|
|
||||
|
|
|
TV Time |
|
3:32PM |
|
|
|
|
|
Picture Source |
|
Ant A 122-1 |
|
|
|
|
|
Channel ID |
|
KPBS-DT |
|
3:32 PM |
|
|
Program Language |
|
Engl |
|
||
|
|
|
Broadcast Rating |
|
720p Format |
|
|
|
|
|
|
TV-Y |
No Info |
|
|
INFO |
|
|
Signal Format |
|
|
INFO |
|
|
Closed |
|
|
|
|
||
|
Captioning |
|
|
|
|
||
|
|
|
Aspect Mode |
|
|
||
Day/Night |
Day |
CC Off |
4:3 Expanded |
|
|
||
Mode |
|
|
|||||
|
View --:-- AM |
--:-- PM REC --:-- AM |
--:-- AM |
INFO |
Return |
||
|
Event Timer |
|
Timer Recording |
|
|
|
3:32 PM S-IN: 3 VID 3
When an S-VIDEO Input is connected to VIDEO: 3.
3:32 PM YPBPR: 1
VID: 1
When a COMPONENT VIDEO: Y-PBPR Input is connected to VIDEO: 1.
NOTES: 1. The Sleep Timer info will show momentarily after releasing INFO button.
2.Press the INFO button again or the EXIT button to return to normal viewing.
24