Heath Zenith UT-9272-BZ, UT-9274-BZ User Manual

0 (0)
Heath Zenith UT-9272-BZ, UT-9274-BZ User Manual

 

 

 

 

Items

Models

Product Description

 

 

 

 

 

247592

UT-9272-BZ

150 Watt High Pressure Sodium Security Light

 

 

 

 

247595

UT-9274-BZ

100 Watt Metal Halide Security Light

 

 

 

 

 

 

 

Questions or problems? Before returning to your retailer, call our technical service department at 1-800-858-8501 (English speaking only), 7:30 am to 4:30 pm, CST, Monday – Friday.

INSTALLATION INSTRUCTIONS

Estimated Installation Time: 45 minutes Items needed for installation (not included):

• Phillips and flathead screwdrivers

3/8" Socket

3/16" Drill bit

Drill

Pliers

Wire strippers/cutters

Safety glasses

Silicone caulk

Ladder

• Small box or rag

READ ALL INSTRUCTIONS CAREFULLY BEFORE

BEGINNING INSTALLATION.

NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system.

Lamp in Fixture Contains Mercury. Dispose According to Local, State, or Federal Laws.

WARNING: Turn power off at the circuit breaker or fuse.

1.Select a location on a flat wall with structurally sound wood and from 10 to 25 feet from the ground. The wood should be at least one inch thick to safely secure the fixture.

2.Attach the cover plate using two large machine screws.

3.Using the mounting bracket as a template. Hold it at the desired mounting location (making sure the bottom is level), and mark four mounting holes. We suggest drilling 3/16" pilot holes for the lag screws.

4.Put the two top lag screws through their holes in the mounting bracket and hold them in place while you push the gasket onto these lag screws. Start these two screws into the two top pilot holes.

5.Start the other two lag screws, and then tighten all four screws.

6.Hang the fixture on the mounting bracket using the slot in the cover plate.

7.Twist the fixture wires to the supply wires (black to black, white to white, and the bare fixture wire to the supply ground wire).

8.Make sure the wires do not get pinched, and swing the fixture up so the base fits tightly against the gasket. Push the pin through the hole at the top near the gasket, and into the mating loop in the mounting bracket. You may need to tap the pin to seat it all the way down.

9.Secure the fixture with the small machine screw going through the cover plate and into the mounting bracket.

10.Install bulb. Bulb rating must match the rating of the fixture. Model 9272: 150 Watt high pressure sodium type S55 bulb. Model 9274: 100 Watt metal halide type M90/O open rated bulb.

11.Hold the lens and wire cage up to the fixture and align the clips on the wire cage with the protrusions in the housing. Hook the clips over these protrusions and snap the clips closed to hold the lens and wire cage in place.

12.Loosen the screw in the center of the photocontrol socket two turns. Twist the socket so that the arrow points north. Note: There is a stop to prevent the socket from turning all the way around. If you have trouble turning the socket, try turning it the other direction. Retighten the screw in the center of the socket.

13.Align the photocontrol (it will only plug-in one way). Plug it in and twist clockwise until it stops.

14.Caulk fixture mounting surface with silicone weather sealant

To test operation during the daytime, cover the photocontrol with a small box or rag. Turn the power on. Light should turn on and reach full brightness within ten minutes. Remove the box or rag to expose the photocontrol to daylight. Light should turn off within two minutes. With the photocontrol exposed, the light will operate automatically – on at dusk and off at dawn.

Housing

Photocontrol

 

 

Pin

Lag Screw

(4) Mounting

Bracket

Cover

Bulb Plate

Gasket

Lens

Package Contents and Fixture Assembly

© 2008 HeathCo LLC

598-1289-04

TECHNICAL SERVICE

Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.com. If the problem persists, call* for assistance at 1-800-858-8501 (English speaking only), 7:30 AM to 4:30 PM CST (M-F). You may also write* to:

HeathCo LLC

P.O. Box 90045, Bowling Green, KY 42102-9045 ATTN: Technical Service

* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

LIFETIME WARRANTY

This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.

For as long as you (the original purchaser) own this product, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.

Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.

This warranty covers only this product and is not extended to other equipment and components that a customer uses in conjunction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty requests.

2

598-1289-04

 

 

 

 

Articulos

Modelos

Descripción del producto

 

 

 

 

 

247592

UT-9272-BZ

Lámpara de seguridad de sodio de alta presión de 150 vatios

 

 

 

 

247595

UT-9274-BZ

Lámpara de seguridad halógena metálica de 100 vatios

 

 

 

 

 

 

 

¿Preguntas o problemas? Antes de devolver el producto al minorista, llame a nuestro departamento de servicio técnico al 1-800-858- 8501 (sólo se habla inglés), de 7:30 am a 4:30 pm, Hora Estándar del Centro, de Lunes a Viernes.

INDICACIONES PARA SU INSTALACIÓN

Tiempo estimado de instalación: 45 minutos

Artículos que se necesitan para la instalación (no incluidos):

• Tornillos Phillips y de cabeza plana

 

 

• Zócalo de 3/8 pulgadas

Broca de 3/16 pulgada

Taladro

Alicates

Desforrador/cortador de alambre

Lentes de seguridad

Calafateo de silicona

Escalera

• Caja pequeña o trapo

LEA TODAS LAS INDICACIONES CON CUIDADO ANTES DE COMENZAR LA INSTALACIÓN.

NOTA: Todo el cableado debe estar hecho de acuerdo al Código Eléctrico Nacional (Código Eléctrico Canadiense en Canadá) por medio de conductos o de otro medio aceptable. Comuníquese con un electricista profesional si tiene preguntas relacionadas con la aptitud del sistema.

La lámpara en el dispositivo contiene mercurio. Deseche de acuerdo con las leyes locales, estatales o federales.

ADVERTENCIA: Desconecte la energía en el cortacircuito.

1.Seleccione la ubicación en una pared plana de madera estructuralmente firme y entre 10-25 pies del suelo. La madera debería ser al menos de una pulgada de espesor para asegurar firmemente al artefacto.

2.Coloque la placa cubertora usando los dos tornillos para metal grandes.

3.Use la consola de montaje como plantilla. Sosténgala en la ubicación de montaje deseada (Asegúrese que la base inferior esté a nivel), y marque la ubicación de los cuatro orificios de montaje. Le sugerimos taladrar orificios guías de 3/16" para los tirafondos.

4.Pase los dos tirafondos superiores por los orificios correspondientes de la consola de montaje y sosténgalos en su lugar mientras empuja el empaque permitiendo que estos tirafondos lo traspasen. Pase estos dos tornillos por los dos orificios guías superiores.

5.Pase los otros dos tirafondos, ajuste luego los cuatro tirafondos.

6.Cuelgue el artefacto en la consola de montaje usando la ranura de la placa cubertora.

7.Entorche los cables del artefacto con los cables de alimentación

(negro con negro, blanco con blanco, y el cable desnudo del artefacto al cable de tierra de alimentación).

8.Asegúrese que los cables no se aprieten y balance el artefacto hacia arriba de modo que la base encaje firmemente contra el empaque. Empuje la clavija por el orificio superior cerca del empaque, y por el ojal de contacto de la consola de montaje. Puede ser necesario golpear ligeramente la clavija para asentarla en el fondo.

pasa por la placa cubertora y la consola de montaje.

10.Instale la bombilla. La potencia nominal de la lámpara debe emparejar con la potencia nominal del artefacto.

Modelo 9272: Bombilla de sodio a alta presión de 150 vatios tipo S55.

Modelo 9274: Bombilla halógena metálica de 100 vatios tipo M90/O.

11.Sostenga la placa traslúcida y la jaula de alambre hacia arriba contra el artefacto y alinee las presillas de la jaula de alambre con las salientes de la carcasa. Enganche las presillas en estos salientes y cierre a presión las presillas para que la placa traslúcida y la jaula de alambre queden en su lugar.

12.Afloje en dos vueltas el tornillo que está en el centro del zócalo del fotocontrol. Gire el zócalo de modo que la flecha apunte al norte. Nota: Hay un tope para impedir que el zócalo gire toda la vuelta. Si Ud. tiene problema en girar el zócalo, inténtelo en la otra dirección. Vuelva a ajustar el tornillo del centro del zócalo.

13.Alinee el fotocontrol (sólo se enchufará de una forma). Enchúfelo y gírelo en sentido horario hasta el tope.

14.Calafatee el aparato y la superficie de montaje con un sellador de silicona contra la intemperie.

Para probar el funcionamiento durante la luz diurna, cubra el fotocontrol con una caja pequeña o un trapo. Conecte la alimentación. La lámpara debe encenderse y alcanzar su brillo máximo en diez minutos. Retire la caja o el trapo para exponer el fotocontrol a la luz diurna. La lámpara debería apagarse en dos minutos. Con el fotocontrol descubierto, la lámpara operará automáticamenteen- cendiéndose en el crepúsculo y apagándose al amanecer.

Carcasa

Fotocontrol

Clavija

Tirafondo(4)

Consola de Montaje

Lámpara

 

(bulbo)

Placa

 

cubertora

Empaque

Placa Traslúcida

9. Asegure el artefacto usando el pequeño tornillo para metal que

 

Contenido del paquete y conjunto artefacto de luz

598-1289-04

3

598-1289-04 S

© 2008 HeathCo LLC

Loading...
+ 5 hidden pages