Heat & Glo LifeStyle Soho24B 2137-900 User Manual

Size:
2.19 Mb
Download

Owner’s Manual

Installation and Operation

Model: Soho24B

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual

and maintenance

these instructions for safe

party responsible for

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch.DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas(Sorte De Gaz): This appliance must be installed in accordance with local codes, if any;if not, follow ANSI Z223.1in the USAor CAN/CGA B149 installation codes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

 

 

Approved Minimum(De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Minimum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN CANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

Table of Contents

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4 E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 4 F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4 G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 H. Requirements for the Commonwealth of Massachusetts. . 5

2 Getting Started

A. Design and Installation Considerations . . . . . . . . . . . . . . . 6

B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6

C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 6

3 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7

B. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

C. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . . 8

D. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . . 9

5 Vent Information and Diagrams

A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

D. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 16 B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 16 C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 17 D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 18

7 Appliance Preparation

A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

B. Installation of Non-combustibleFacing Material . . . . . . . 20

C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 21

8 Installing Vent Pipe

A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 22 B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 23 C. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 23 D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 24 E. Install Decorative Ceiling Components . . . . . . . . . . . . . . 24 F. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 25 G. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 25 H. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 26 I. Install Decorative Wall Components . . . . . . . . . . . . . . . . 26 J. Heat Shield Requirements for Horizontal Termination . . . 26 K. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 27

9 Gas Information

A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

10 Electrical Information

A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 30 B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 30 C. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 30 D. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 31

11 Finishing

A. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

B. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

C. Installation of Non-CombustibleFacing Materials . . . . . . 33

12 Appliance Setup

A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 34

B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

D. Positioning Stones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

E. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

F. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

G. Reflective Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

13 Operating Instructions

A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 38 B. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 39 C. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 40

14 Troubleshooting

A. IntelliFire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . .

41

15 Maintaining and Servicing Appliance

 

 

A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43

 

16 Reference Materials

 

 

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . .

45

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . .

46

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50

D. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . .

53

 

E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

55

 

= Contains updated information.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

3

1 Listing and Code Approvals

A. Appliance Certification

MODELS: Soho24B

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance Heater

STANDARD: ANSIZ21.88a-2007CSA2.33a-2007

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports

02-31919.01and 02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

Note: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

C. BTU Specifications

Models

Maximum

Minimum

Orifice

Size

U.S. (0-2000ft.) or Canada(2000-4500ft.)

Input BTU/h

Input BTU/h

(DMS)

 

 

 

 

 

 

 

 

 

Soho24 (NG)

US

14,000

N/A

50

 

 

 

 

CAN

12,600

N/A

51

 

 

 

 

 

 

Soho24LP

US

13,000

N/A

59

 

 

 

 

CAN

11,700

N/A

60

 

 

 

 

 

 

D. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750ºC, shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

4

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

H.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,

“GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2) (a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

5

2 Getting Started

A. Design and Installation Considerations

C. Inspect Appliance and Components

Heat & Glo direct vent gas appliances are designed to

 

 

WARNING

operate with all combustion air siphoned from outside of

 

 

the building and all exhaust gases expelled to the outside.

 

 

Inspect appliance and components for damage.

No additional outside air source is required.

 

 

 

 

Damaged parts may impair safe operation.

 

 

CAUTION

 

 

• Do NOT install damaged components.

 

 

 

 

• Do NOT install incomplete components.

 

 

 

 

 

 

 

 

 

 

 

 

• Do NOT install substitute components.

 

Check building codes prior to installation.

 

 

Report damaged parts to dealer.

 

• Installation MUST comply with local, regional, state and

 

 

 

 

national codes and regulations.

Carefully remove the appliance and components from

 

• Consult local building, fire officials or authorities having jurisdic-

 

 

the packaging.

 

tion about restrictions, installation inspection, and permits.

 

 

 

 

 

• The vent system components and trim doors are shipped

When planning an appliance installation, it’s necessary to

 

in separate packages.

The gas logs may be packaged separately and must be

determine the following information before installing:

Where the appliance is to be installed.

 

field installed.

Report to your dealer any parts damaged in shipment,

The vent system configuration to be used.

 

particularly the condition of the glass.

Gas supply piping.

 

 

 

Read all of the instructions before starting the insta-

Electrical wiring.

 

 

 

llation. Follow these instructions carefully during the

Framing and finishing details.

 

installation to ensure maximum safety and benefit.

Whether optional accessories—devicessuch as a fan,

 

 

 

 

wall switch, or remote control—aredesired.

 

 

WARNING

 

 

 

 

 

 

 

 

 

WARNING

 

 

Hearth & Home Technologies disclaims any

 

 

 

 

 

responsibility for, and the warranty will be voided

 

Keep appliance dry.

 

 

by, the following actions:

 

 

Installation and use of any damaged appliance or vent

 

Mold or rust may cause odors.

 

 

 

 

system component.

 

Water may damage controls.

 

 

 

 

Modification of the appliance or vent system.

 

 

 

 

 

 

 

 

 

 

Installation other than as instructed by Hearth & Home

B. Tools and Supplies Needed

 

 

Technologies.

Before beginning the installation be sure that the following

 

• Improper positioning of the gas logs or the glass door.

 

• Installation and/or use of any component part not approved

tools and building supplies are available.

 

 

 

by Hearth & Home Technologies.

 

 

 

 

 

 

Reciprocating saw

Framing material

 

Any such action may cause a fire hazard.

Pliers

 

Noncorrosive leak check solution

 

 

 

Hammer

 

Gloves

 

 

 

Phillips screwdriver

Framing square

 

 

 

Flat blade screwdriver

Electric drill and bits (1/4 in.)

 

 

 

Plumb line

 

Safety glasses

 

 

 

Level

 

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews

Manometer Voltmeter

Tape measure

Caulking material (300ºF minimum continuous exposure rating)

6

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

3 Framing and Clearances

Note:

Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

Illustrations/diagrams are not drawn to scale.

Actual installation may vary due to individual design preference.

A.Selecting Appliance Location

When selecting a location for your appliance it is important to consider the required clearances to walls (see figure 3.1).

WARNING

Fire Risk

Provide adequate clearance:

Around air openings

To combustibles

• For service access

Locate appliance away from traffic areas.

NOTE: For actual appliance dimensions refer to Section 16.

B. Mantel Projections

A Studio front is required for all installs. No mantels are allowed when using Studio fronts.

E

A

1/2 IN.

 

 

B

A

 

ALCOVE

B

 

C

INSTALLATION

 

 

 

TOP VENT,

D

 

ONE 90º ELBOW

 

 

 

A

B

C

D

E

Inches

33-1/8

29-1/8

46-3/4

35-1/8

12

 

 

 

 

 

 

Millimeters

841

740

1187

892

305

In addition to these framing dimensions, also reference the following sections:

Clearances and Mantel Projections (Section 3B).

Vent Clearances and Framing (Section 6).

Figure 3.1 Appliance Locations

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

7

C. Constructing the Appliance Chase

on a cement surface, a layer of plywood may be placed

A chase is a vertical boxlike structure built to enclose

underneath to prevent conducting cold up into the room.

D. Clearances

the gas appliance and/or its vent system. Vertical vents

that run on the outside of a building may be, but are not

WARNING

required to be, installed inside a chase.

Construction of the chase may vary with the type of building.

Fire Risk.

These instructions are not substitutes for the requirements

Odor Risk.

of local building codes. Local building codes MUST be

Install appliance on hard metal or wood surfaces

checked.

extending full width and depth of appliance.

Chases should be constructed in the manner of all outside

Do NOT install appliance directly on carpeting,

vinyl, tile or any combustible material other than

walls of the home to prevent cold air drafting problems.

wood.

The chase should not break the outside building envelope

 

in any manner.

WARNING

Walls, ceiling, base plate and cantilever floor of the chase

Fire Risk.

should be insulated. Vapor and air infiltration barriers

should be installed in the chase as per regional codes for

Construct chase to all clearance specifications

the rest of the home. Additionally, in regions where cold

in manual.

air infiltration may be an issue, the inside surfaces may be

Locate and install appliance to all clearance

sheetrocked and taped for maximum air tightness.

specifications in manual.

To further prevent drafts, the wall shield and ceiling firestops

CAUTION

should be caulked with caulk with a minimum of 300ºF

continuous exposure rating to seal gaps. Gas line holes

 

and other openings should be caulked with caulk with a

The Soho24B requires an elevated platform construction

minimum of 300ºF continuous exposure rating or stuffed

to accommodate the Studio fronts, which are larger than

with unfaced insulation. If the appliance is being installed

the appliance.

A

 

F

 

 

 

 

 

 

 

G

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I

 

 

C

 

 

 

 

K

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

CLEARANCES TO COMBUSTIBLES:

 

 

 

 

A

B

C

D

E

F

G

H

I

J

K

 

Rough

Rough

Rough

Rough

Minimum

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

Opening

Opening

Opening

Opening

Platform

 

(Vent Pipe)

(Height)

(Depth)

(Width)

Height

to Ceiling

Floor

Flooring

Appliance Appliance Appliance

 

 

 

 

 

 

 

Inches

8-5/8

44

11-1/2

30-1/8

3

28

0

0

1/2

1/2

36

mm

219

1118

292

765

76

711

0

0

13

13

914

Figure 3.2 Clearances to Combustibles

 

 

 

 

 

 

 

 

8

 

 

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

 

 

 

4 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

(See Figure 4.4 for specific clearances)

Figure 4.1

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 4.2 Minimum height from roof to lowest discharge opening

Figure 4.2 specifies minimum vent heights for various pitched roofs.

A

B

6 in. (minimum) up to 20 in.

18 in. minimum

152 mm/508 mm

457 mm

20 in. and over

0 in. minimum

Gas, Wood or Fuel Oil

Termination Cap

B

A *

Gas

Termination

Cap **

*If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

**In a staggered installation with both gas and wood or fuel oil terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Figure 4.3 Multiple Vertical Termination

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

9

 

 

 

 

 

 

 

 

 

 

 

O

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

C

 

 

 

F

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

Q

 

J

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

H or i

 

 

 

 

 

 

 

V

 

B

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

D

X

V

 

E

 

 

V

 

 

 

 

G

 

 

 

 

 

 

 

V

 

H

 

 

 

 

 

 

 

 

 

V

M

 

 

V

 

 

 

 

 

 

 

 

V

V

H V

 

 

L

 

 

 

 

 

 

A

A

 

 

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

 

 

 

 

V

Electrical

K

V

 

V

 

 

 

 

 

 

 

 

= VENT TERMINAL

 

 

 

 

 

 

 

Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X = AIR SUPPLY INLET

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

 

 

 

V

 

 

A

=

12 inches.................

clearances above grade, veranda,

 

 

Covered Alcove Applications

 

 

 

 

porch, deck or balcony

 

 

 

 

 

 

(Spaces open only on one side and with an overhang)

 

B

=

12 inches

clearance to window or door that may

 

N

=

6 inches ...........

non-vinylsidewalls

 

 

 

 

be opened, or to permanently closed

 

 

12 inches

vinyl sidewalls

 

 

 

 

window

 

 

 

 

 

 

O

=

18 inches

non-vinylsoffit and overhang

 

C

=

18 inches

clearance below unventilated soffit

 

 

 

42 inches

vinyl soffit and overhang

 

 

 

18 inches

clearance below ventilated soffit

 

 

 

 

 

P

=

8 ft.

 

 

 

 

30 inches

clearance below vinyl soffits and

 

 

 

 

 

 

 

 

 

 

 

 

 

electrical service

 

 

 

QMIN

RMAX

 

D

=

6 inches...................

clearance to outside corner

 

1 cap

3 feet

2 x Q ACTUAL

 

E

=

6 inches...................

clearance to inside corner

 

2 caps

6 feet

1 x Q ACTUAL

 

F

=

3 ft. (Canada)

not to be installed above a gas me-

 

 

 

3 caps

9 feet

2/3 x Q ACTUAL

 

 

 

 

ter/regulator assembly within 3 feet

 

 

 

 

 

horizontally from the center-lineof the

 

4 caps

12 feet

1/2 x Q ACTUAL

 

 

 

 

regulator

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

 

G

=

3 ft

clearance to gas service regulator

 

 

 

 

 

 

 

 

 

 

vent outlet

 

 

Measure vertical clearances from this surface.

 

H

=

9 inches (U.S.A)

 

 

 

 

 

 

 

 

 

 

 

 

 

12 inches (Canada).clearance to non-mechanical(unpow-

 

 

 

 

 

 

 

 

 

ered) air supply inlet, combustion air

 

 

 

 

 

 

i

=

3 ft. (U.S.A.)

inlet or direct-venttermination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 ft. (Canada)...........

clearance to a mechanical (powered)

 

 

 

 

 

 

 

 

 

air supply inlet

 

 

 

 

 

 

All mechanical air intakes within 10 feet of a termination cap

 

 

 

 

 

 

must be a minimum of 3 feet below termination.

 

 

 

 

 

 

J

=

7 ft..........................

On public property: clearance above

 

 

 

 

 

 

 

 

 

paved sidewalk or a paved driveway.

 

 

 

 

 

 

A vent shall not terminate directly above a sidewalk or paved

 

Measure horizontal clearances from this surface.

 

driveway which is located between two single family dwellings

 

 

and serves both dwellings.

 

CAUTION! Risk of Burns! Termination caps are HOT,

 

 

 

 

 

 

 

 

 

 

consider proximity to doors, traffic areas or where people

 

K

=

6 inches

clearance from sides of electrical

may pass or gather (sidewalk, deck, patio, etc.). Listed cap

 

shields available. Contact your dealer.

 

 

 

 

 

service

• Local codes or regulations may require different

 

L

=

12 inches

clearance above electrical service

 

clearances.

 

 

 

Location of the vent termination must not interfere with access to the

 

 

 

• Vent system termination is NOT permitted in screened

 

electrical service.

 

 

 

 

 

 

porches.

 

 

 

M

=

18 inches ....................

clearanceunderveranda,porch,deck,

• Vent system termination is permitted in porch areas with

 

 

 

 

balcony or overhang

two or more sides open.

 

 

 

 

42 inches ................

vinyl or composite overhang

• Hearth & Home Technologies assumes no responsibility

 

Permitted when veranda, porch, deck or balcony is fully open

for the improper performance of the appliance when the

 

on a minimum of 2 sides beneath the floor.

 

 

 

 

 

venting system does not meet these requirements.

Figure 6.3 Minimum Clearances for Termination

• Vinyl protection kits are suggested for use with vinyl siding.

 

10

 

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

 

 

5 Vent Information and Diagrams

A. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

 

 

V1

First section (closest to appliance) of vertical length

 

 

V2

Second section of vertical length

 

 

H1

First section (closest to appliance) of horizontal length

 

 

H2

Second section of horizontal length

 

 

WARNING

Fire Hazard. Explosion Risk. Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney flue serving a separate solid-fuelor gas burning appliance.

• Vent this appliance directly outside.

• Use separate vent system for this appliance.

May impair safe operation of this appliance or other appliances connected to the flue.

B. Use of Elbows

CAUTION

ALL vent configuration specifications MUST be followed.

This product is tested and listed to these specifications.

Appliance performance will suffer if specifications are not followed.

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 5.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2(216 mm) inches horizontal run and8-1/2(216 mm) inches vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 5.1).

Vertical

 

 

in.

 

 

 

 

 

.

1/2

 

 

in

 

12

8-

 

 

 

8-1/2in.

 

Horizontal

Figure 5.1

C. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

1.Pipe measurements are shown using the effective length of pipe (see Figure 5.2).

2.Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 4.1).

3.Vertical terminations are measured to bottom of termination cap.

4.Horizontal pipe installed level with no rise.

 

Effective Height/Length

 

Pipe

inches

mm

 

SLP4

4

102

 

SLP6

6

152

Effective

SLP12

12

305

Height/

SLP24

24

610

Length

SLP36

36

914

 

 

SLP48

48

1219

 

SLP6A

2 - 6

51 - 152

 

SLP12A

2 - 12

51 - 305

Figure 5.2 SLP Pipe Effective Length

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

11

D. Vent Diagrams

WARNING

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between ceiling firestops.

ALWAYS maintain specified clearances around venting and firestop systems.

Install wall shield and ceiling firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

1. Top Vent - Horizontal Termination

One Elbow

V1 Minimum

H1 Maximum

Elbow only

1-1/2ft.

457 mm

 

 

1 ft.

305 mm

2-1/2ft.

762 mm

 

1-1/2ft.

457 mm

3-1/2ft.

1.1 m

 

2-1/2ft.

762 mm

5-1/2ft.

1.7 m

V1

3-1/2ft.

1.1 m

7-1/2ft.

2.3 m

H1

4-1/2ft.

1.4 m

15-1/2ft.

4.7 m

V1

+ H1 = 39 ft. (11.9 m) Maximum

 

 

H1 =15-1/2ft. (4.7 m) Maximum

Figure 5.3

Two Elbows

V1 Minimum

H1 + H2 Maximum

2 - 90º elbows

Cannot do

back to back

 

 

 

 

 

 

6 in

152 mm

1 1/2 ft.

457 mm

 

 

 

 

1-1/2ft.

457 mm

2-1/2ft.

762 mm

2-1/2ft.

762 mm

4-1/2ft.

1.4 m

3-1/2ft.

1.1 m

6-1/2ft.

1.9 m

 

 

 

 

5-1/2ft.

1.7 m

15-1/2ft.

4.7 m

V1 + H1+ H2 = 48 ft. (14.6 m) Maximum H1 + H2 =15-1/2ft. (4.7 m) Maximum

H2

V1

H1

 

Figure 5.4

INSTALLED

HORIZONTALLY

12

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

1. Top Vent - Horizontal Termination - (continued)

Three Elbows

V1 Min.

 

H1 Max.

V2 Min.

H2 Max.

Elbow only

2 ft.

 

610 mm

*

= V2

1 ft.

304 mm

2 ft.

 

610 mm

*

= V2

1-1/2ft.

457 mm

3 ft.

 

914 mm

*

= V2

2-1/2ft.

762 mm

5 ft.

 

1.5 m

*

= V2

3-1/2ft.

1.1 m

7 ft.

 

2.1 m

*

= V2

4-1/2ft.

1.4 m

15 ft.

 

4.6 m

*

= 0

 

 

 

 

 

 

 

*When using V2 , H2 Max = V2. If V2 = 0, then H2 Max =1-1/2ft. (38 mm) (H1 + H2 ) cannot exceed 15 ft. (4.6 m) when using appropriate V2.

H2

V2

H1V1

Figure 5.5

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

13

2. Top Vent - Vertical Termination

No Elbow

V1 = 45 ft Max. (13.72 m) V1 = 3 ft Min. (914 mm)

Note: The vertical termination baffle should be used for runs of 7 feet or greater. Use the vertical termination baffle for these applications:

• Extended vertical vent runs

• Extended vertical and horizontal vent runs with PVK-80Power Vent.

The vertical restrictor has a break away portion that creates a larger hole. If venting 7-15feet, the break away portion MUST be removed and the larger hole must be used. If venting over 15 feet, the break away portion should be left in place and the small hole should be used. ForPVK-80Power Vent applications, the break away portion should be left in place and the small hole should be used.

V1

Figure 5.6

 

 

 

 

 

 

 

 

 

BREAK AWAY PORTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VERTICAL TERMINATION BAFFLE

 

 

 

 

 

 

 

Two Elbows

V1 Minimum

 

 

 

 

H1 Maximum

V2

V1 + V2

Minimum

 

One Elbow

 

 

 

1-1/2ft.

457 mm

*

*

*

 

1/2 ft.

152 mm

 

2 ft.

610 mm

*

*

*

 

1-1/2ft.

457 mm

 

3 ft.

914 mm

*

*

*

 

2-1/2ft.

762 mm

 

5 ft.

1.5 m

*

*

*

 

3-1/2ft.

1.1 m

 

 

7 ft.

2.1 m

*

*

*

 

5-1/2ft.

1.7 m

 

 

15 ft.

4.6 m

*

*

*

 

 

 

 

V1 + V2 + H1 = 38 ft. (11.6 m) Max.

 

 

 

V2

*No specific restrictions on this value EXCEPT

 

 

V

1

+ V

2

+ H

1

cannot exceed 38 ft. (11.6 m)

 

 

 

 

 

 

 

 

 

 

 

V1

H1

Figure 5.7

14

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

2. Top Vent - Vertical Termination - (continued)

Three Elbows

V1 Minimum

 

 

H1+ H2 Maximum

V2

V1+ V2 Minimum

Elbow only

 

 

1/2 ft.

 

152 mm

*

*

*

1/2 ft.

152 mm

 

 

1 ft.

 

 

305 mm

*

*

*

 

 

 

 

 

 

 

 

 

 

 

1-1/2ft.

457 mm

 

 

2 ft.

 

 

610 mm

*

*

*

 

 

 

 

 

 

 

 

 

 

 

2-1/2ft.

762 mm

 

 

4 ft.

 

 

1.2 m

*

*

*

3-1/2ft.

1.1 m

 

 

 

6 ft.

 

 

1.8 m

*

*

*

4-1/2ft.

1.4 m

 

 

 

14 ft.

 

 

4.3 m

*

*

*

 

 

 

 

 

 

 

 

H + H = 14 ft (4.3 m) Maximum

 

 

 

V + V

1

+ H2

+ H

2

= 37 ft (11.3 m) Maximum

 

 

1

2

1

 

 

 

 

 

 

 

*No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot

 

 

 

 

exceed

 

37 ft. (11.3 m)

 

 

 

V2

H1

H2

V1

 

INSTALLED

HORIZONTALLY

Figure 5.8

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

15

6 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).

SLP heat shield - designed to be used on a wall4-3/8in. to7-5/8in. (111 mm to 194 mm thick).

If wall thickness is less than 4-3/8the existing heat shields must be field trimmed. If wall thickness is greater than7-5/8in. a DVP-HSM-Bwill be required.

Heat 2-1/2in. (64 mm)Shields top clearance at

wall shield firestops

3 in. (76 mm) top clearance

1 in. (25 mm) clearance around vertical sections

Wall

1/2 in. (13 mm) bottom

clearance at wall

Shield

shield firestops

Firestop

 

1 in. (25 mm)

WALL

clearance

 

bottom and sides

 

Figure 6.1 Horizontal venting clearances to combustible materials

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield firestop. The wall shield firestop maintains minimum clearances and prevents cold air infiltration.

The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.

SLP pipe - A wall shield firestop must be placed on each side of an interior wall. A minimum 1-1/2in. (38 mm) overlap of attached heat shields must be maintained.

See Section 8.L. for information for regarding the installation of a horizontal termination cap.

Non-CombustibleWall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one in. greater than the pipe is acceptable.

Whenever a non-combustiblewall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.

10 in. 10 in.

B

A*

A*

B

38 in.

37 in.

*Shows center of vent framing hole for top venting. The center of the hole is one (1) inch (25.4 mm) above the center of the horizontal vent pipe.

Figure 6.2 Exterior Wall Hole

16

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

C. Vertical Penetration Framing

A ceiling firestop MUST be used between floors and attics.

Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/ floor (see Figure 6.3).

Frame the area with the same sized lumber

as used in ceiling/floor joist.

• The ceiling firestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between floors that are not insulated. Refer to Figure 6.4.

• Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept back from the pipe to prevent overheating.

Figure 6.3

ATTIC ABOVE

A

A

PIPE

A

 

 

SLP

9 in. (229 mm)

 

 

INSTALL ATTIC INSULATION SHIELDS

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

3 FASTENERS

 

PER SIDE

 

CEILING FIRESTOP

CEILING FIRESTOP

INSTALLED BELOW CEILING

INSTALLED ABOVE CEILING

Figure 6.4 Installing the Attic Shield

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

17

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specified clearance and be secured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Vaulted Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Cut the attic insulation shield (if application is for vaulted ceiling) to fit your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90°

TO MAINTAIN CLEARANCE

AND PREVENT INSULATION

FROM FALLING INSIDE

BEND 3 TABS

OUTWARD TO

FASTEN TO CEILING

FIRESTOP-BEND

REMAINING TABS

INWARD 90 DEGREES

TO MAINTAIN

INSERT 3 CLEARANCE

SCREWS

Figure 6.5 Attic Insulation Shield

18

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

7 Appliance Preparation

A. Top Vent

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

ELBOW HEAT SHIELD

Figure 7.1

An elbow heat shield is attached to the Soho24B. Do not remove this heat shield.

SUPPORT TAB

ROPE RING

Figure 7.2

If venting with a 90 degree elbow directly off of the top of the unit, the heat shield should be placed as shown. Rotate the heat shield up to the vertical position and fold the tab down to contact the elbow. Make sure the rope ring, found in the manual bag, is in place around the elbow before attaching more pipe.

Figure 7.3

This is a view from the front of the unit when the elbow heat shield is properly in place.

ROPE RING

Figure 7.4

If venting vertically or using vertical pipe before the elbow, rotate the elbow heat shield to a vertical position and fold the heat shield in half as shown. Make sure the rope ring, found in the manual bag, is in place around the first sec-

tion of vent pipe.

Figure 7.5

This is a view from the front of the unit when not using an 90 degree elbow directly off the top of the unit.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

19

B.Installation of Non-combustibleFacing Material

The non-combustibleassembly is located on the left side of appliance.

CAUTION

Handle with care.

Non-combustiblematerial may be damaged if dropped.

Remove and save two screws from upper bracket.

Remove non-combustiblepieces.

Remove and save two screws from lower bracket.

Discard brackets.

Replace screws in holes where brackets were attached to appliance.

Attach non-combustiblepanel to appliance and framing with supplied screws. See Figures 7.6, 7.7 and 7.8.

WARNING

Fire Risk.

Follow these instructions exactly.

Facing materials must be installed properly to prevent fire.

• No materials may be substituted without authorization by Hearth & Home Technologies.

Use regular sheetrock screws in non-shadedareas.

Use a wet or dry towel or soft brush to remove dust or dirt from facing material.

Apply a non-combustibleadhesive to attach tile, stone or othernon-combustiblefinishing materials per manufacturer’s instructions.

NON-COMBUSTIBLE

ZONE

37.9"

31.7"

Figure 7.6 Complete Installation of Non-combustibleFacing

Material

NON-COMBUSTIBLEFACING MATERIAL

SUPPLIED LEFT SIDE OF APPLIANCE

Figure 7.7 Attaching Non-combustibleFacing Material

20

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

C. Securing and Leveling the Appliance

WARNING

Fire Risk.

Prevent contact with sagging, loose insulation.

Do NOT install against combustible materials

such as exposed insulation, plastic and insulation backer.

The diagram shows how to properly position, level, and secure the appliance (see Figure 7.8). Nailing tabs are provided to secure the appliance to the framing members.

Place the appliance into position.

Level the appliance from side to side and front to back.

Shim the appliance as necessary. It is acceptable to use wood shims.

Bend out nailing tabs on each side.

Keep nailing tabs flush with the framing.

Secure the appliance to the framing by using nails or screws through the nailing tabs and two holes in each end of outer non-combustiblepanel.

NAILING TABS

(BOTH SIDES)

Figure 7.8 Proper Positioning, Leveling and Securing of a

Appliance

WARNING

Fire Risk.

• ALWAYS maintain specified

clearances around the appliance.

• Do NOT notch into the framing around the appliance spacers.

Failure to keep insulation, framing or other material away from the appliance may cause fire.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

21

8 Installing Vent Pipe

A. Assemble Vent Sections

To attach the first vent component to the starting collars of the appliance:

Lock the vent components into place by sliding the pipe section onto the collar.

Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 8.1.

Slide the gasket over the first vent section and place it flush to the appliance. This will prevent cold air infiltration. Caulk with a minimum of 300ºF continuous exposure rating may be used to hold the part in place.

Continue adding vent components, locking each succeeding component into place.

Ensure that each succeeding vent component is securely fitted and locked into the preceding component.

Commercial, Multi-family(Multi-levelexceeding two stories), orHigh-RiseApplications

For Installation into a commercial, multi-family(multi-levelexceeding two stories) orhigh-riseapplications: All outer pipe joints must be sealed with silicone with a minimum of 300ºF continuous exposure rating, including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 8.2

Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 8.1 Adding Venting Components

Figure 8.2 High Temperature Silicone Sealant

22

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

B. Assemble Slip Sections

Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 8.3.

Slide together to the desired length.

Pilot hole

Figure 8.3 Slip Section Pilot Holes

Maintain a 1-1/2in. (38 mm) overlap between the slip section and the pipe section.

Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 8.4.

Figure 8.4 Screws into Slip Section

Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a high temperature silicone sealant.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

Only outer pipes are sealed, sealing the inner flue is not required.

All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed.

C. Secure the Vent Sections

Vertical runs of SLP pipe must be supported every 8 ft. (2.44 m).

Horizontal sections must be supported every 5 feet (1.52 m).

Vent supports or plumbers strap (spaced 120º apart) may be used to support. See Figures 8.5 and 8.6.

Wall shield firestops may be used to provide horizontal support.

SLP ceiling firestops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

Figure 8.5 Securing Vertical Pipe Sections

Figure 8.6 Securing Horizontal Pipe Sections

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

23

D. Disassemble Vent Sections

Rotate either section (see Figure 8.7) so the seams on both pipe sections are aligned as shown in Figure 8.8.

Pull carefully to separate the pieces of pipe.

Figure 8.7 Rotate Seams for Disassembly

Figure 8.8 Align and Disassemble Vent Sections

E. Install Decorative Ceiling Components

A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling thimble is used to cover the firestop.

Seal the gap between the vent pipe and firestop using silicone with a minimum of 300ºF continuous exposure rating to prevent cold air infiltration.

Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.

A decorative cathedral ceiling support box can be installed on a cathedral ceiling through which the vent passes.

Use a plumb-bobto mark the center line of the venting system on the ceiling and drill a small hole through the ceiling and roof at this point. Locate the hole and mark the outline of the cathedral ceiling support box on the outside roof.

Remove shingles or other roof covering as necessary to

cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure 8.9).

Level the support box both vertically and horizontally and temporarily tack it in place through the inside walls into the roof sheathing.

Use tin snips to cut the support box from the top corners down to the roof line and fold the resulting flaps to the roof. See Figure 8.10.

Nail the flaps to the roof AFTER running a bead of non hardening sealant between the flaps and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

LEVEL

CATHEDRAL CEILING

SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm)

GREATER IN SIZE THAN

PATTERN OF SUPPORT

BOX AS IT IS PROJECTED

ONTO ROOF LINE

Figure 8.9

Figure 8.10

24

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

F. Install Metal Roof Flashing

See minimum vent heights for various pitched roofs (Figure 8.11) to determine the length of pipe to extend through the roof.

Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 8.12.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12............................1.25*

Over 7/12 to 8/12..............................1.5*

Over 8/12 to 9/12..............................2.0*

Over 9/12 to 10/12............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12........................... 5.0

Over 14/12 to 16/12........................... 6.0

Over 16/12 to 18/12........................... 7.0

Over 18/12 to 20/12........................... 7.5

Over 20/12 to 21/12........................... 8.0

* 3 foot minimum in snow regions

Figure 8.11 Minimum Height From Roof To Lowest Discharge

Opening

 

 

NOTICE: Failure to properly caulk the roof flashing and pipe seams may permit entry of water.

Caulk the gap between the roof flashing and the outside diameter of the pipe.

Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 8.12.

Caulk the overlap seam of any exposed pipe sections that are located above the roof line.

CAULK

Figure 8.12

G. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Connect both halves of the storm collar with two screws (see Figure 8.13).

Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 8.14).

Caulk around the top of the storm collar (see Figure 8.15).

Figure 8.13 Assembling the Storm Collar

Figure 8.14 Assembling the Storm Collar Around the Pipe

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

25

H. Install Vertical Termination Cap

Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

Secure the cap by driving three self-tappingscrews (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 8.15).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 8.15

I. Install Decorative Wall Components

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the firestop.

Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 8.16.

J.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.

DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 8.17).

Heat shields must overlap 1-1/2in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attachedto the wall shield firestop. The other section isfactory-attachedto the cap. See Figure 8.17.

If the wall thickness does not allow the required 1-1/2in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

If the wall thickness is less than 4-3/8in. (111 mm), the heat shields on the cap and wall shield firestop must be trimmed. A minimum1-1/2in. (38 mm) overlap MUST be maintained.

Use an extended heat shield if the finished wall thickness is greater than 7-1/4in. (184 mm).

The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2in. (38 mm) overlap between heat shields.

Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields maynot be field constructed.

Figure 8.16 Wall Thimble

26

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

K. Install Horizontal Termination Cap

WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent.

1-1/2(38 mm) minimum overlap of flue telescoping section is required.

Failure to maintain overlap may cause overheating and fire.

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at outside edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current

ANSI Z223.1 and CAN/CGA-B149installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

NOTICE: For certain exposures which require superior resistance towind-drivenrain penetration, a flashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps withfactory-suppliedheat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

HEAT SHIELD

EXTENDED

1-1/2IN. (38 MM) MIN.

HEAT SHIELD

OVERLAP

WALL SHIELD

 

FIRESTOP

 

SLIP SECTION

 

CAN BE EXTENDED

 

INNER VENT

SHEATHING

OUTER VENT

 

INTERIOR

EXTERIOR

Figure 8.17 Venting through the wall

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

27

9 Gas Information

A. Fuel Conversions

C. Gas Connection

Before making gas connections ensure that appliance being installed is compatible with the available gas type.

Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressures

Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA54.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressures must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 inches

11.0 inches

w.c.

w.c.

 

Maximum inlet gas pressure

14.0 inches

14.0 inches

w.c.

w.c.

 

Manifold pressure

3.5 inches

10.0 inches

w.c.

w.c.

 

Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Refer to Reference Section 16 for location of gas line access in appliance.

Note: Gas line may be run from either side of the appliance provided the hole in the outer wrap does NOT exceed2-1/2inches in diameter and does not penetrate the firebox.

WARNING

Gas Leak Risk

Support control when attaching pipe to prevent bending gas line.

NOTE: The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed withnon-combustible,unfaced insulation to prevent cold air infiltration.

28

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes.

Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.

WARNING

Fire or Explosion Hazard

Gas buildup during line purge may ignite.

Purge should be performed by qualified technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING

CHECK FOR GAS LEAKS

Explosion Risk

Fire Risk

Asphyxiation Risk

Check all fittings and connections.

Do not use open flame.

After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially-available,non-corrosiveleak check solution. Be sure

to rinse off all leak check solution following testing.

Fittings and connections may have loosened during shipping and handling.

WARNING

Fire hazard.

Do NOT change the valve settings.

• This valve has been preset at the factory.

• Changing valve settings may result in fire hazard or bodily injury.

HIGH ALTITUDE INSTALLATIONS

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

29

10 Electrical Information

A. Recommendation for Wire

This appliance requires 110-120VAC be wired to the junction box either for proper operation of the appliance.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

B.Connecting to the Appliance

C. IntelliFire Ignition System Wiring

This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.1.

This appliance is equipped with an IntelliFire control valve which operates on a 3 volt system.

This appliance is supplied with a 3 volt AC transformer which requires the installation of the supplied junction box. It is highly recommended that the junction box be installed at this time to avoid reconstruction.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

If using thermostat use one compatible with a millivolt gas valve system.

Follow parameters for locating thermostat (see individual thermostat instructions) to ensure proper operation of appliance.

Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.

Keep wire lengths as short as possible by removing any excess wire length.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

WARNING

Shock hazard.

Replace damaged wire with type 105º C rated wire.

Wire must have high temperature insulation.

30

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

PLUG-IN

 

 

 

3V TRANSFORMER

 

 

ON/OFF

 

 

 

WALL SWITCH

 

 

 

IGNITION

 

 

 

MODULE

 

 

 

(3V)

 

 

 

VALVE

LOW VOLTAGE

 

 

SEE NOTE 1

 

NEUTRAL

GROUND

REMOTE

HOT

 

 

CONTROL

BLACK WIRE CAN BE

PLUGGED INTO ANY

OF #1 - #5 LOCATIONS

ON THE HOT SIDE

WHITE WIRE CAN BE

PLUGGED INTO ANY

OF#1 - #5 LOCATIONS

ON THE NEUTRAL SIDE

TRANSFORMER

3 VAC

PLUG-IN

IGNITION MODULE 3 VAC

INTERMITTENT

PILOT IGNITOR

 

 

ORG

 

 

 

WHT

 

 

 

GROUND TO

 

 

 

FIREPLACE

 

 

 

CHASSIS*

 

BLK

 

ORG

 

 

 

 

RED

BRN

 

GRN

BRN

 

 

 

 

THERMOSTAT

 

 

 

WIRE

 

 

VALVE

ASSEMBLY

 

 

 

REMOTE

JUMPER WIRE

Figure 10.1 IntelliFire Pilot Ignition (IPI) Wiring Diagram - Standard Method. Note: Appliance will not operate unless properly grounded.

D. Junction Box Installation

If the box is being wired from the OUTSIDE of the appliance:

Remove the cover plate located on the outer shell - right side (see Figure 10.2).

Install the supplied Romex™ connector in the cover plate.

Feed the necessary length of wire through the connector.

Make all necessary wire connections and reattach the cover plate to the outer shell.

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box/ receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 10.2).

Pull the electrical wires from outside the appliance through this opening into the valve compartment.

 

Romex

 

Connector

 

14/2WG

 

Cover Plate

 

outside firebox

WHT

 

BLK

 

WHT

 

BLK

Copper

 

GRN wire

ground attached

to GRN screw with

inside box

GRN wire

 

NOTE: Do NOT wire

 

110VAC to wall switch.

Figure 10.2 Junction Box Detail

Feed the necessary length of wire through the connector.

Make all necessary wire connections to the junction box/ receptacle and reassemble the junction box/receptacle to the

outer shell.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

31

11 Finishing

A. Facing Material

WARNING

Fire Risk.

Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles.

Modifying or covering grilles could cause temperature rise and fire hazard.

Finishing materials must not interfere with:

Air flow through grilles or louvers.

Operation of louvers or doors.

Access for service.

FINISH WALL MATERIAL MAY BE

COMBUSTIBLE - TOP AND SIDES

8 in.

NON-COMBUSTIBLEZONE

0 in.

 

 

31-11/16in.

0 in.

 

 

 

 

 

 

 

 

 

 

 

0 in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEALANT MATERIAL

 

 

 

 

 

 

 

WARNING

Fire Risk.

Finish all edges and fronts to clearances and specifications listed in manual.

Black metal appliance front may be covered with noncombustible material only.

Do NOT overlap combustible materials onto appliance front.

Install combustible materials up to specified clearances on top, front and side.

Seal joints between the finished wall and appliance top and sides using only a 300ºF minimum sealant.

B.Mantel Projections

A Studio front is required for all installs. No mantels are allowed when using Studio fronts.

Figure 11.1 Noncombustible Facing Diagram

WARNING

Risk of Fire

Non-combustibleclearancesMUST be maintained.

Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in thenon-combustiblezone.

See Section 11 for proper clearances.

See Section 1for combustible/non-combustible definitions.

32

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

C.Installation of Non-CombustibleFacing Materials

Gypsum wallboard (drywall) joints adjacent to the fireplace opening require special attention to minimize potential development of cracking. Hearth and Home Technologies recommends the following steps to minimize potential cracks in the finished drywall around the fireplace opening:

When installing gypsum wallboard around the fireplace, install the hole for the fireplace opening in a single wallboard sheet, if possible. This will minimize the joints adjacent to the fireplace opening.

The factory-suppliednon-combustibleboard and the gypsum wallboard must join on the structural framing, where applicable. Wallboard andnon-combus-tible board should be fastened to the framing with at least 1.25" long screw fasteners, located within 1.5" from each corner, and at no more than 12" intervals along the joint length.

The wall-boardjoints should be finished with a Taping Coat, followed by at least two subsequent Finish Coats of joint compound.

For the initial Taping Coat, it is critical that a generalpurpose chemically hardening joint compound, such as SHEETROCK™ Brand Durabond™ Setting-TypeJoint Compound, be used to fill the joint and embed the mesh tape.Fiberglass-meshtape is recommended because it will provide a morecrack-resis-tant joint than one finished with paper tape. Let the Taping Coat properly cure before applying subsequent Finish Coats.

For the second and third finishing coats, it is acceptable to use a light-weightjoint compound and standard application, curing and sanding methods.

Do not operate the fireplace during the drywall finishing process. Allow the finish coat to cure for at least 24 hours prior to using the appliance.

Painting

If desired finishing includes a painted wall, 100% acrylic latex with compatible primer is recommend around the appliance. Oil-basedor standard acrylic paints may discolor due to heat exposure.

Wallboard Joint-CrackPrevention and Repair

Wallboard joints around the fireplace will be affected by exposure to elevated temperatures, along with other environmental and structural factors. The specific methods presented in the previous section will help prevent or minimize development of cracks.

If a crack does emerge adjacent the fireplace, it can be permanently repaired by filling it with spackling paste or paintable latex caulk, followed by repainting.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

33

12 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 16.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listedaccessories voids warranty.

Using non-listedaccessories may result in a safety hazard.

Only Hearth & Home Technologies approved

accessories may be used safely.

34

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

D. Positioning Stones

For proper performance and safety, it is critical that the Black Onyx stones are set up in accordance with these instructions.

Stone Placement: Soho24B

WARNING! Choking Hazard! Keep stones out of reach of children.

BURNER AREA

Figure 12.1.

As you are positioning the stones, make sure that no stones are in the cross-hatchedarea shown between the two arrows above. This is to ensure proper lighting and avoid interference with the pilot flame.

WARNING

Delayed Ignition Risk

Place stones according to instructions.

Do NOT place stones in area in front of pilot shield.

Do NOT place stones in a position that they may fall into area in front of pilot shield.

Do NOT use any media other than the stones supplied with this fireplace.

Fireplace will not function properly.

Delayed ignition may occur.

JIG

PILOT SHIELD

Figure 2.

Step 1. The included stone placement jig MUST be used any time stones are placed on the burner to ensure that none end up in thecross-hatchedarea noted in Figure 1.

Figure 12.3.

Step 2. The stone placement jig is shipped in its proper position. Remove the two screws securing the jig, making sure the jig stays in the proper position. See Figure 3.

Figure 12.4.

Step 3. Place a single layer of stones over the burner area inside of the tabs surrounding the burner and behind the pilot shield.

Figure 12.5.

Step 4. Place the remaining stones over the basepan taking care not to add more stones to the burner area.

2137-936C

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

35

Figure 12.6.

Step 5. Carefully place a layer of stones over the pilot shield to disguise it.

Figure 12.7.

Step 6. Spread the stones out evenly. Double check that there is only one layer of stones on the burner area and that thecross-hatchedarea in Figure 1 is still free of stones.

Figure 12.8.

Step 7. Carefully remove the stone placement jig making sure that no stones fall into the pilot area.

NO STONES IN THIS AREA

Figure 12.9.

Step 8. This is a view of the front area of the pilot shield. This area must be free of stones for safe operation.

36

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

E. Glass Assembly

WARNING

Handle glass doors with care.

Inspect the gasket to ensure it is undamaged.

Inspect the glass for cracks, chips or scratches.

Do NOT strike, slam or scratch glass.

Do NOT operate appliance with glass door removed, cracked, broken or scratched.

Replace glass door assembly as a complete appliance.

Removing Glass Assembly

Pull the two glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance (see Figure 12.10).

Replacing Glass Assembly

Replace the glass door on the appliance. Pull out and latch the two glass assembly latches into the groove on the glass frame.

GLASS

ASSEMBLY

BOTTOM

LATCH

Figure 12.10 Glass Assembly

F. Air Shutter Setting

 

NG

LP

Burner

1/16 in.

Full Open

G. Reflective Panel

The back and sides of the SOHO are covered with a reflective panel. This panel will bronze with burning, but it will retain its reflectivity.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

37

13 Operating Instructions

A. Before Lighting Appliance

CAUTION

If installing IntelliFire ignition battery backup:

Do not install batteries if the backup mode may not be used for extended time.

Batteries may leak.

Install batteries only when needed for power outage.

Before operating this appliance have a qualified technician:

Remove all shipping materials from inside and/or underneath the firebox.

Review proper placement of logs, rockwool, lava rock, and vermiculite.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position.

Ensure that the flow of combustion and ventilation air is not obstructed (front grilles and vent caps).

WARNING

Glass door must be in place when appliance is operating.

Risk of:

Combustion Fumes

Fire

Do NOT operate appliance with glass door removed.

Open viewing glass for servicing only.

Glass door MUST be in place and sealed before operating appliance.

Only use glass door certified for use with appliance.

Glass replacement should be done by qualified technician.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

38

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

B. Lighting Instructions (IPI)

The IPI system may be operated with two D-cellbatteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

Final inspection by

LIGHTING

INSTRUCTIONS (IPI)

1.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

3.To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4.If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2.Service technician should turn off electric power to the control when performing service.

593-913G

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

39

C. After Appliance is Lit

Initial Break-inProcedure

When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

NOTE: The appliance should be run three to four hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours.

During this break-inperiod it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

WARNING

Fire Risk.

High Temperatures.

Keep combustible household items away from appliance.

Do NOT obstruct combustion and ventilation air.

Do NOT place combustible items on top of or in front of appliance.

Keep furniture, draperies away from appliance.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

CAUTION

Smoke and odors released during initial operation.

Open windows for air circulation.

Leave room during initial operation.

Smoke may set off smoke detectors.

Smoke and odors may be irritating to sensitive individuals.

WARNING

Fire Hazard.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

Do NOT store flammable materials in the appliance’s vicinity.

• Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids in this appliance.

• Combustible materials may ignite.

D. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

condensation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appliance is al-

lowed to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this appliance may release an odor for the first several hours. This is

Odor from appliance

caused by the curing of the paint and the burning off of any oils remaining from manufactur-

ing. Odor may also be released from finishing materials and adhesives used around the

 

 

appliance.

 

 

 

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

Film on the glass

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See

 

your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the appliance.

 

 

Is it normal to see the pilot flame burn

In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is

turned off. Some optional control systems available with IPI models may allow pilot flame to

continually?

remain lit.

 

 

 

40

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

14 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

A. IntelliFire Ignition System

Sympton

1. The ignitor/module makes noise, but no spark.

2. Pilot won’t light, there is no noise or spark.

3. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot flame has been lit, flame rectification has not occurred.)

Possible Cause

Corrective Action

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to

 

correct terminals on module and pilot assembly. Reversed wires at the module may

 

cause system to make sparking noise, but spark may not be present at pilot hood.

 

 

b. Loose connections

Verify no loose connections or electrical shorts in wiring from module to pilot assem-

or electrical shorts in

bly. Rod closest to pilot hood should be ignitor. Verify connections underneath pilot

the wiring.

assembly are tight; also verify connections are not grounding out to metal chassis,

 

pilot burner, pilot enclosure, mesh screen if present, or any other metal object.

c. Ignitor gap is too

Verify gap of igniter to pilot hood. The gap should be approximately .17 inch or 1/8

large.

inch.

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire

 

“I” from module. Place ON/OFF Rocker switch or wall switch in ON position. Hold

 

ground wire about 3/16 inch away from “I” terminal on module. If there is no spark

 

at “I” terminal module must be replaced. If there is a spark at “I” terminal, module

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked insulator around

 

electrode.

a. Transformer

Verify that transformer is installed and plugged into module. Check voltage of trans-

installed correctly.

former under load at spade connection on module with ON/OFF switch in ON posi-

 

tion. Acceptable readings of a good transformer are between 3.2 and 2.8 volts AC.

b. A shorted or loose

Remove and reinstall the wiring harness that plugs into module. Verify there is a

connection in wiring

tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each

configuration or wiring

wire in wiring harness.

harness.

 

c. Improper wall switch

Verify that 110/VAC power is “ON” to junction box.

wiring.

 

d. Module not

Verify black ground wire from module wire harness is grounded to metal chassis of

grounded.

appliance.

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire

 

“I” from module. Place ON/OFF Rocker switch or wall switch in ON position. Hold

 

ground wire about 3/16 inch away from “I” terminal on module. If there is no spark

 

at “I” terminal module must be replaced. If there is a spark at “I” terminal, module

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked insulator around

 

electrode.

a. A shorted or loose

Verify all connections to wiring diagram in manual. Verify connections underneath

connection in sensor

pilot assembly are tight. Verify connections are not grounding out to metal chassis,

rod.

pilot burner, pilot enclosure or screen if present, or any other metal object.

b. Poor flame rectifi-

Verify that flame is engulfing sensor rod. If the pilot assembly does not have a

cation or contaminated

ground strap, consider installing one to increase flame rectification. Verify correct pi-

sensor rod.

lot orifice is installed and inlet gas specifications. Flame carries rectification current,

 

not the gas. If flame lifts from pilot hood, the circuit is broken. A wrong orifice or too

 

high an inlet pressure can cause pilot flame to lift. The sensor rod may be contami-

 

nated. Polish sensor rod with fine steel wool.

c. Module is not

Verify that module is securely grounded to metal chassis of appliance. Verify that

grounded.

wire harness is firmly connected to module.

 

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

41

IntelliFire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

 

3. Continued

d. Damaged pilot as-

Verify that ceramic insulator around the sensor rod is not cracked, damaged, or

 

sembly or dirty sensor

loose. Verify connection from sensor rod to white sensor wire. Polish sensor rod with

 

rod.

fine steel wool to remove any contaminants that may have accumulated on sensor

 

 

 

rod. Verify continuity with a multimeter with ohms set at lowest range.

 

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire

 

 

 

“I” from module. Place ON/OFF Rocker switch or wall switch in ON position. Hold

 

 

 

ground wire about 3/16 inch away from “I” terminal on module. If there is no spark

 

 

 

at “I” terminal module must be replaced. If there is a spark at “I” terminal, module

 

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked insulator around

 

 

 

electrode.

 

4. Pilot sparks, but

a. Correct gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet pressure reading is

 

Pilot will not light.

 

within acceptable limits.

 

 

b. Ignitor gap is too

Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in.

 

 

large.

 

 

 

c. Module is not

Verify module is securely grounded to metal chassis of appliance.

 

 

grounded.

 

 

42

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

15 Maintaining and Servicing Appliance

A. Maintenance Tasks

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

Turn off gas.

Turn off electricity to appliance.

Disable remote control, if one is present.

Ensure appliance is completely cooled.

After servicing:

Replace any screen or barrier that was removed.

Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

Condition of doors, surrounds and fronts.

Condition of glass, glass assembly and glass seal.

Obstructions of combustion and ventilation air.

Condition of logs.

Condition of firebox.

Burner ignition and operation.

Burner air shutter adjustment

Gas connections and fittings.

Obstructions of termination cap.

Clean:

• Glass

Air passageways, grilles, control compartment

Burner, burner ports

Risk of:

Fire

Delayed ignition or explosion

Exposure to combustion fumes

Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial3-4hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when hot.

Turn off appliance after 3-4hours of operation and ALLOW TO COOL.

Remove and clean glass assembly.

Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

43

Inspect

 

Maintenance Tasks

 

 

Doors, Surrounds

1. Assess condition of screen and replace as necessary.

and Fronts

 

Recommend addition of screen if one is not present.

 

2.

Inspect for scratches, dents or other damage and repair as necessary.

 

 

 

 

3.

Verify no obstructions to airflow through the louvers.

 

 

 

 

4.

Verify maintenance of proper clearance to combustible household objects.

 

 

Gasket Seal, Glass

1. Inspect gasket seal and its condition.

Assembly and Glass

 

 

2.

Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.

 

 

 

 

 

3.

Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

4.

Verify that latches engage properly, clip studs are not stripped, and glass attachment components are intact

 

 

and operating properly. Replace as necessary.

 

5.

Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.

 

 

 

Valve Compartment

1.

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw

and Firebox Top

 

tips that have penetrated the sheet metal are sharp and should be avoided.

 

2.

Remove any foreign objects.

 

 

 

 

3.

Verify unobstructed air circulation.

 

 

 

Logs

1.

Inspect for broken, damaged, or missing logs. Replace as necessary.

 

 

 

 

2.

Verify correct log placement and no flame impingement causing sooting. Correct as necessary.

 

 

 

Firebox

1.

Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.

 

 

 

 

2.

Replace appliance if firebox has been perforated.

 

 

 

Burner Ignition and

1.

Verify burner is properly secured and aligned with pilot or igniter.

Operation

 

 

2.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

 

 

 

 

 

3.

Replace ember materials with new dime-sizeand shape pieces. Do not block ports or obstruct lighting paths.

 

 

 

 

4.

Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.

 

 

 

 

5.

Inspect for lifting or other flame problems.

 

 

 

 

6.

Verify air shutter is clear of dust and debris.

 

 

 

 

7.

Inspect orifice for soot, dirt or corrosion.

 

 

 

 

8.

Verify manifold and inlet pressures. Adjust regulator as required.

 

 

 

 

9.

Inspect pilot flame strength. Clean or replace orifice as necessary.

 

 

 

10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Polish with fine

 

 

steel wool or replace as required.

 

11. Verify millivolt output. Replace as necessary.

 

 

Venting

1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.

 

 

 

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

 

 

 

3.

Verify that termination cap clearance to subsequent construction (building additions, decks, fences or

 

 

sheds) has been maintained.

 

4.

Inspect for corrosion or separation.

 

 

 

 

5.

Verify weather stripping, sealing and flashing remains intact.

 

 

 

 

6.

Inspect draft shield to verify it is not bent, damaged or missing.

 

 

Remote controls

1. Verify operation of remote.

 

 

 

 

2.

Replace batteries in remote transmitters and battery-poweredreceivers.

 

 

 

 

3.

Verify batteries have been removed from battery back-upIPI systems to prevent premature battery failure

 

 

or leaking.

44

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

 

 

 

 

I

 

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

L

K

 

 

 

 

 

 

 

 

 

 

 

ØN

 

M

 

 

 

 

 

 

 

 

 

 

 

O

 

C

 

 

 

 

 

 

 

 

 

 

 

D

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Q

 

 

 

E

 

 

F

 

 

 

 

 

 

 

GAS LINE

 

 

 

B

 

 

 

ELECTRICAL

ACCESS

P

 

 

 

 

 

 

ACCESS

 

 

 

A

 

 

 

G

 

 

 

 

 

 

 

 

Appliance Dimensions Table

 

 

 

 

 

 

Location

Inches

Millimeter

Location

Inches

Millimeter

 

A

29-1/8

740

J

11-1/2

 

292

 

 

B

25-9/32

643

K

11-1/2

 

292

 

 

C

37-3/16

945

L

11

 

279

 

 

D

29-3/16

742

M

5-9/16

 

142

 

 

E

4-1/8

105

N

6-5/8

 

168

 

 

F

2-3/16

56

O

37

 

940

 

 

G

4-1/2

115

P

3-3/4

 

96

 

 

H

32-3/4

832

Q

2-1/4

 

57

 

 

I

23-1/16

586

 

 

 

 

 

Figure 16.1 Appliance Dimensions

 

 

 

 

 

 

 

 

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

 

45

B. Vent Components Diagrams

SL Series Components

13-7/8in.

(352 mm)

9-1/2in.

(241 mm)

14 in.

(356 mm)

DRC-RADIUS

Cap Shield

11-5/8in.

(295 mm)

7-1/8in.

12-1/8in.

(308 mm)

(181 mm)

 

5-3/4in. (146 mm)

COOL-ADD

Cap Shield

Figure 16.1 SLP Series Vent Components

46

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

B. Vent Components Diagrams(continued)

8-3/4in.

222 mm

Effective

Height/

Length

SLP PIPE

 

6-1/2in.

6-1/2in.

165 mm

 

165 mm

6-1/2in.

 

6 in.

165 mm9-1/4in.

235 mm

152 mm

 

6-5/8in.

 

168 mm

6-5/8in.

SLP45

168 mm

45° Elbow

 

9-7/8in.

251 mm

SLP90

90° Elbow

Effective Height/Length

Pipe

inches

mm

SLP4

4

102

 

 

 

SLP6

6

152

SLP12

12

305

SLP24

24

610

 

 

 

SLP36

36

914

SLP48

48

1219

 

 

 

SLP6A

2 - 6

51 - 152

SLP12A

2 - 12

51 - 305

 

 

 

10-7/8in.

276 mm

8-7/8in.

 

 

 

 

 

 

 

 

 

 

 

1-1/2in.

 

 

 

 

 

 

 

 

 

 

 

225 mm

 

 

 

 

 

 

 

 

 

 

 

38 mm

 

 

 

SLP-HVS

Horizontal Pipe

Support

8-11/16in.

 

12 in.

 

220 mm

 

 

 

305 mm

 

 

 

 

8-11/16in.

1-1/2in.

12 in.

5-1/2in.

220 mm

38 mm

305 mm

146 mm

SLP-FS

 

SLP-WS

 

Ceiling Firestop

 

Wall Shield Firestop

 

Figure 16.2 SLP Series Vent Components

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

47

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm). The heat shield is designed to be used on a wall 4 in. to7-1/4in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than7-1/4in. (184 mm) aDVP-HSM-Bwill be required.

 

8 in.

 

 

 

 

(203 mm)

 

 

 

 

Heat

 

 

 

 

Shield

 

 

 

15-1/8in.

 

 

 

 

(384 mm)

 

 

 

 

 

 

Term Cap

Minimum

Maximum

 

 

Effective Length

Effective Length

 

Max

 

12 in.

Trap1

3-1/8in.

4-3/4in.

Effective

79 mm

121 mm

(305 mm)

Length

 

 

5-1/4in.

9-1/4in.

 

SLP-TRAP

Trap2

 

133 mm

235 mm

 

Horizontal Termination Cap

 

 

 

 

 

 

6-11/16in.

3-15/16in.

6-3/8in.

4-3/16in.

 

(169 mm)

(101 mm)

163 mm

106 mm

3-15/16in.

3-13/16in.

 

4 in.

4-5/8in.

(101 mm)

(97 mm)

 

102 mm

117 mm

 

8 in.

5-1/16in.

8-1/8in.

5-1/16in.

 

(128 mm)

 

(203 mm)

206 mm

128 mm

 

 

 

SL-2DVP

 

 

DVP-2SL

 

Adapter

 

 

Adapter

 

 

26 in.

 

14-7/16in.

660 mm

 

 

 

367 mm

 

 

 

DVP-HSM-B

14-7/16in.

2-5/16in.

Extended Heat Shield

59 mm

 

367 mm

 

 

 

SLP-WT-BK

Wall Thimble-Black

ASSEMBLY

SLP90 SL-2DVP

 

PVK-80

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: Use the vertical termination baffle with thePVK-80.See Figure 5.6.

(For use on Intellifire appliances only)

Figure 16.3 SLP Series Vent Components

48

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

B. Vent Components Diagrams (continued)

14 in.

356 mm

10-9/16in.

269 mm

SLP-CCS-BK

Cathedral Ceiling

Support Box-Black

14-1/16in.

357 mm

 

 

10-3/4in.

14 in.

7-1/2in.

273 mm

 

356 mm

192 mm

 

SLP-FLEX-TRAP

Horizontal

Termination Kit

10-11/16in. 271mm

28-1/2in.

724 mm

13-1/2in.

343 mm

SLK-SNKD

Snorkel

Termination Cap

Figure 16.3 SLP Series Vent Components

13 in.

330 mm

13 in.

1-5/16in.

34 mm

330 mm

 

SLP-DCF-BK

Ceiling Firestop

Black

12 in.305 mm

12-1/2in.318 mm

SLP-TVHW

Vertical

Termination Cap

 

7-1/4in.

1 in.

(184 mm)

(25 mm)

 

14 in.

(356 mm)

3/8 in. (10 mm) 1 in. (25 mm)

7-3/4to10-3/8in.

(197 to 264 mm)

DVP-FBHT

Horizontal

Termination Cap

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

49

C. Service Parts

 

SOHO24B

24 x 24 Direct Vent Fireplace

Beginning Manufacturing Date: Aug. 2007

 

 

 

Ending Manufacturing Date: ______

 

 

 

1

 

 

 

2

 

4

3

 

 

 

 

 

5

 

 

 

6

 

 

8

7

 

 

10

9

 

13

 

 

 

 

 

12

11

 

 

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

 

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

1

Heat Shield

 

2137-138

 

 

2

Non-combustibleBoard (Outside)

 

2111-148

 

 

 

Bracket Non-combustibleBoard

 

2111-128

 

 

 

Non-combustibleBoard (Inside)

 

2077-148

 

 

3

Surround

 

2077-112

 

 

4

Heat Shield Retainer

 

2137-134

 

 

5

Reflective Panel

 

2137-135

 

 

6

Stone Placement Jig

 

2137-140

 

 

7

Pilot Cover (Outer)

 

2137-137

 

 

8

Pilot Cover (Inner)

 

2137-136

 

 

9

Base Pan

 

2137-129

 

 

10

Glass Door Assembly

 

GLA-SOHO24B

Y

 

11

Valve/ Burner Assembly

 

Refer to valve page

 

 

12

Junction Box

 

4021-013

Y

 

13

Wire, Wall Switch

 

2045-024

Y

Additional service part numbers appear on following page.

50

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

Service Parts

SOHO24B

 

 

 

Beginning Manufacturing Date: Aug. 2007

 

Ending Manufacturing Date: ______

#11 IPI Valve Assembly

11.1

11.2

11.3

11.4

11.5

11.611.16

11.711.15

11.8

 

11.10

 

 

 

 

 

11.9

 

11.14

 

 

 

 

 

 

 

 

 

11.12

1113

 

 

 

 

11.11

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

11.1

Pilot Assembly NG

 

 

2090-012

Y

Pilot Assembly LP

 

 

2090-013

Y

 

 

 

11.2

Burner Assembly NG

 

 

2137-010

Y

Burner Assembly LP

 

 

2137-011

Y

 

 

 

11.3

Pilot Cover Bracket

 

 

2137-141

 

11.4

Pilot Bracket

 

 

2137-102

 

11.5

Flexible Gas Connector

 

 

530-302A

Y

11.6

Burner Neck Gasket

 

 

438-407

 

11.7

Valve Plate Gasket

 

 

2077-138

 

11.8

Battery Pack

 

 

593-594A

Y

11.9

Valve Bracket

 

 

2111-186

 

11.10

Flex Ball Valve Assembly

 

 

302-320A

Y

11.11

Valve NG

 

 

593-500

Y

Valve LP

 

 

593-501

Y

 

 

 

11.12

3 Volt Transformer

 

 

593-593A

Y

11.13

Module

 

 

593-592

Y

11.14

Module Wire Assembly

 

 

593-590A

Y

11.15

Orifice NG (#50C)

 

 

582-850

Y

Orifice LP (#59C)

 

 

582-859

Y

 

 

 

11.16

Grommet, 3-Hole

 

 

2118-420

 

Additional service part numbers appear on following page.

 

 

 

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

51

Service Parts

SOHO24B

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Black Onyx

 

SOHO24B-ONYX

 

 

Fiber Glass Rope

 

045-455

 

 

Flue Restrictor

 

2137-139

 

 

Glass Latch Assembly

Qty 2 req

339-121A

Y

 

Glass Latch Assembly

Pkg of 2

33858/2

Y

 

Remote Wire Assembly

 

2103-013

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

Wall Switch Control Kit

No longer available

WSK100-HNG

 

 

Post Nov 2007

WSK-21

 

 

 

 

 

Conversion Kit NG

NGK-SOHO24B

Y

 

Conversion Kit LP

LPK-SOHO24B

Y

 

Pilot Orifice NG

593-528

Y

 

Pilot Orifice LP

593-527

Y

 

Regulator NG

NGK-DXF

Y

 

Regulator LP

LPK-DXF

Y

52

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

D. Limited Lifetime Warranty

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

 

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

Parts

Labor

Gas

Wood

Pellet

EPA

Coal

Electric

Venting

Components Covered

 

 

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

 

 

1 Year

X

X

X

X

X

X

X

covered by Conditions,

 

 

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

 

 

2 years

 

 

 

 

and glass

 

 

 

 

 

 

 

 

 

 

 

X

X

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

X

X

 

 

 

Manifold tubes,

 

 

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

Burners, logs and refractory

 

 

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

X

X

X

 

 

Firebox and heat exchanger

 

 

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

X

X

All replacement parts

 

 

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

4021-645C12-29-10

 

 

 

 

 

 

 

Page 1 of 2

 

 

 

 

 

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

53

D. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

7KLV ZDUUDQW\ RQO\ FRYHUV ++7 DSSOLDQFHV WKDW DUH SXUFKDVHG WKURXJK DQ ++7 DXWKRUL]HG GHDOHU RU GLVWULEXWRU $ OLVW RI ++7 DXWKRUL]HG GHDOHUV LV DYDLODEOH RQ WKH ++7 EUDQGHG ZHEVLWHV

7KLV ZDUUDQW\ LV RQO\ YDOLG ZKLOH WKH ++7 DSSOLDQFH UHPDLQV DW WKH VLWH RI RULJLQDO LQVWDOODWLRQ

&RQWDFW \RXU LQVWDOOLQJ GHDOHU IRU ZDUUDQW\ VHUYLFH ,I WKH LQVWDOOLQJ GHDOHU LV XQDEOH WR SURYLGH QHFHVVDU\ SDUWV FRQWDFW WKH QHDUHVW ++7 DXWKRUL]HG GHDOHU RU VXSSOLHU $GGLWLRQDO VHUYLFH IHHV PD\ DSSO\ LI \RX DUH VHHNLQJ ZDUUDQW\ VHUYLFH IURP D GHDOHU RWKHU WKDQ WKH GHDOHU IURP ZKRP \RX RULJLQDOO\ SXUFKDVHG WKH SURGXFW

&KHFN ZLWK \RXU GHDOHU LQ DGYDQFH IRU DQ\ FRVWV WR \RX ZKHQ DUUDQJLQJ D ZDUUDQW\ FDOO 7UDYHO DQG VKLSSLQJ FKDUJHV IRU SDUWV DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

WARRANTY EXCLUSIONS:

7KLV ZDUUDQW\ GRHV QRW FRYHU WKH IROORZLQJ

&KDQJHV LQ VXUIDFH ILQLVKHV DV D UHVXOW RI QRUPDO XVH $V D KHDWLQJ DSSOLDQFH VRPH FKDQJHV LQ FRORU RI LQWHULRU DQG H[WHULRU VXUIDFH ILQLVKHV PD\ RFFXU 7KLV LV QRW D IODZ DQG LV QRW FRYHUHG XQGHU ZDUUDQW\

'DPDJH WR SULQWHG SODWHG RU HQDPHOHG VXUIDFHV FDXVHG E\ ILQJHUSULQWV DFFLGHQWV PLVXVH VFUDWFKHV PHOWHG LWHPV RU RWKHU H[WHUQDO VRXUFHV DQG UHVLGXHV OHIW RQ WKH SODWHG VXUIDFHV IURP WKH XVH RI DEUDVLYH FOHDQHUV RU SROLVKHV

5HSDLU RU UHSODFHPHQW RI SDUWV WKDW DUH VXEMHFW WR QRUPDO ZHDU DQG WHDU GXULQJ WKH ZDUUDQW\ SHULRG 7KHVH SDUWV LQFOXGH SDLQW ZRRG SHOOHW DQG FRDO JDVNHWV ILUHEULFNV JUDWHV IODPH JXLGHV OLJKW EXOEV EDWWHULHV DQG WKH GLVFRORUDWLRQ RI JODVV

0LQRU H[SDQVLRQ FRQWUDFWLRQ RU PRYHPHQW RI FHUWDLQ SDUWV FDXVLQJ QRLVH 7KHVH FRQGLWLRQV DUH QRUPDO DQG FRPSODLQWV UHODWHG WR WKLV QRLVH DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

'DPDJHV UHVXOWLQJ IURP IDLOXUH WR LQVWDOO RSHUDWH RU PDLQWDLQ WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK WKH LQVWDOODWLRQ

 

LQVWUXFWLRQV RSHUDWLQJ LQVWUXFWLRQV DQG OLVWLQJ DJHQW LGHQWLILFDWLRQ ODEHO IXUQLVKHG ZLWK WKH DSSOLDQFH IDLOXUH WR

 

LQVWDOO WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK ORFDO EXLOGLQJ FRGHV VKLSSLQJ RU LPSURSHU KDQGOLQJ LPSURSHU RSHUD-

 

WLRQ DEXVH PLVXVH FRQWLQXHG RSHUDWLRQ ZLWK GDPDJHG FRUURGHG RU IDLOHG FRPSRQHQWV DFFLGHQW RU LPSURSHUO\

 

LQFRUUHFWO\ SHUIRUPHG UHSDLUV HQYLURQPHQWDO FRQGLWLRQV LQDGHTXDWH YHQWLODWLRQ QHJDWLYH SUHVVXUH RU GUDIWLQJ

 

FDXVHG E\ WLJKWO\ VHDOHG FRQVWUXFWLRQV LQVXIILFLHQW PDNH XS DLU VXSSO\ RU KDQGOLQJ GHYLFHV VXFK DV H[KDXVW IDQV RU

 

IRUFHG DLU IXUQDFHV RU RWKHU VXFK FDXVHV XVH RI IXHOV RWKHU WKDQ WKRVH VSHFLILHG LQ WKH RSHUDWLQJ LQVWUXFWLRQV

 

LQVWDOODWLRQ RU XVH RI FRPSRQHQWV QRW VXSSOLHG ZLWK WKH DSSOLDQFH RU DQ\ RWKHU FRPSRQHQWV QRW H[SUHVVO\ DXWKRUL]HG

 

DQG DSSURYHG E\ ++7 PRGLILFDWLRQ RI WKH DSSOLDQFH QRW H[SUHVVO\ DXWKRUL]HG DQG DSSURYHG E\ ++7 LQ ZULWLQJ

 

DQG RU LQWHUUXSWLRQV RU IOXFWXDWLRQV RI HOHFWULFDO SRZHU VXSSO\ WR WKH DSSOLDQFH

 

1RQ ++7 YHQWLQJ FRPSRQHQWV KHDUWK FRPSRQHQWV RU RWKHU DFFHVVRULHV XVHG LQ FRQMXQFWLRQ ZLWK WKH DSSOLDQFH

 

$Q\ SDUW RI D SUH H[LVWLQJ ILUHSODFH V\VWHP LQ ZKLFK DQ LQVHUW RU D GHFRUDWLYH JDV DSSOLDQFH LV LQVWDOOHG

++7¶V REOLJDWLRQ XQGHU WKLV ZDUUDQW\ GRHV QRW H[WHQG WR WKH DSSOLDQFH¶V FDSDELOLW\ WR KHDW WKH GHVLUHG VSDFH ,QIRUPDWLRQ LV SURYLGHG WR DVVLVW WKH FRQVXPHU DQG WKH GHDOHU LQ VHOHFWLQJ WKH SURSHU DSSOLDQFH IRU WKH DSSOLFDWLRQ &RQVLGHUDWLRQ PXVW EH JLYHQ WR DSSOLDQFH ORFDWLRQ DQG FRQILJXUDWLRQ HQYLURQPHQWDO FRQGLWLRQV LQVXODWLRQ DQG DLU WLJKWQHVV RI

WKH VWUXFWXUH

This warranty is void if:

7KH DSSOLDQFH KDV EHHQ RYHU ILUHG RU RSHUDWHG LQ DWPRVSKHUHV FRQWDPLQDWHG E\ FKORULQH IOXRULQH RU RWKHU GDPDJLQJ FKHPLFDOV 2YHU ILULQJ FDQ EH LGHQWLILHG E\ EXW QRW OLPLWHG WR ZDUSHG SODWHV RU WXEHV UXVW FRORUHG FDVW LURQ EXEEOLQJ FUDFNLQJ DQG GLVFRORUDWLRQ RI VWHHO RU HQDPHO ILQLVKHV

7KH DSSOLDQFH LV VXEMHFWHG WR SURORQJHG SHULRGV RI GDPSQHVV RU FRQGHQVDWLRQ

7KHUH LV DQ\ GDPDJH WR WKH DSSOLDQFH RU RWKHU FRPSRQHQWV GXH WR ZDWHU RU ZHDWKHU GDPDJH ZKLFK LV WKH UHVXOW RI EXW QRW OLPLWHG WR LPSURSHU FKLPQH\ RU YHQWLQJ LQVWDOODWLRQ

LIMITATIONS OF LIABILITY:

7KH RZQHU¶V H[FOXVLYH UHPHG\ DQG ++7¶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

4021-645C12-29-10

Page 2 of 2

54

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

E. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

2000-945

Printed in U.S.A. - Copyright 2012

Heat & Glo • Soho24B • 2137-900Rev. P • 8/12

55