Heat & Glo LifeStyle SLR32 User Manual

Size:
2.78 Mb
Download

Owner’s Manual

Installation and Operation

Model:

SLR32

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual

and maintenance

these instructions for safe

party responsible for

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch.DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas fireplace, an elegant and clean alternative to wood burning fireplaces. The Heat & Glo gas fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas fireplace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fireplace products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your fireplace.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on fireplace: _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.

Type of Gas

Gas and Electric

Information

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas(Sorte De Gaz): This appliance must be installed in accordance with local codes, if any;if not, follow ANSI Z223.1 in the USAor CAN/CGA B149 installation codes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

 

 

Approved Minimum(De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Minimum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN CANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

Safety Alert Key:

DANGER! Indicates a hazardous situation which, if not avoidedwill result in death or serious injury.

WARNING! Indicates a hazardous situation which, if not avoidedcould result in death or serious injury.

CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 7 C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7 E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 7 F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 7 G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 H. Requirements for the Commonwealth of Massachusetts. . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10 E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 F. Remote Controls, Wall Controls and Wall Switches. . . . . 10 G. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10 H. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11 I. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 J. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .13

B. Maintenance Tasks-QualifiedService Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 15

B. Design and Installation Considerations . . . . . . . . . . . . . . 16

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 16

D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 16

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 17

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 18

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 20

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 22

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 34 B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 34 C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 35 D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 36

9 Appliance Preparation

A. Preparing Elbow Heat Shield . . . . . . . . . . . . . . . . . . . . . . 37

B. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 38

10 Installing Vent Pipe (SLP Pipe)

A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 39 B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 40 C. Secure The Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . 40 D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 41 E. Install Decorative Ceiling Components . . . . . . . . . . . . . . 41 F. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 42 G. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 42 H. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 43 I. Install Decorative Wall Components . . . . . . . . . . . . . . . . 43 J. Heat Shield Requirements for Horizontal Termination . . . 43 K. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 44

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 46

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

B. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 47

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 47

D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 48

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 48

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

3

13 Finishing

A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 49

B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 52

C. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

D. Decorative Fronts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 56

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 56

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

E. Glass Rock Media Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

G. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

H. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

15 Troubleshooting

A. IntelliFire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 59

16 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 61

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 62

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

= Contains updated information.

4

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

B. Limited Lifetime Warranty

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

 

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

Parts

Labor

Gas

Wood

Pellet

EPA

Coal

Electric

Venting

Components Covered

 

 

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

 

 

1 Year

X

X

X

X

X

X

X

covered by Conditions,

 

 

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

 

 

2 years

 

 

 

 

and glass

 

 

 

 

 

 

 

 

 

 

 

X

X

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

X

X

 

 

 

Manifold tubes,

 

 

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

Burners, logs and refractory

 

 

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

X

X

X

 

 

Firebox and heat exchanger

 

 

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

X

X

All replacement parts

 

 

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

4021-645C12-29-10

 

 

 

 

 

 

 

Page 1 of 2

 

 

 

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

5

B. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

7KLV ZDUUDQW\ RQO\ FRYHUV ++7 DSSOLDQFHV WKDW DUH SXUFKDVHG WKURXJK DQ ++7 DXWKRUL]HG GHDOHU RU GLVWULEXWRU $ OLVW RI ++7 DXWKRUL]HG GHDOHUV LV DYDLODEOH RQ WKH ++7 EUDQGHG ZHEVLWHV

7KLV ZDUUDQW\ LV RQO\ YDOLG ZKLOH WKH ++7 DSSOLDQFH UHPDLQV DW WKH VLWH RI RULJLQDO LQVWDOODWLRQ

&RQWDFW \RXU LQVWDOOLQJ GHDOHU IRU ZDUUDQW\ VHUYLFH ,I WKH LQVWDOOLQJ GHDOHU LV XQDEOH WR SURYLGH QHFHVVDU\ SDUWV FRQWDFW WKH QHDUHVW ++7 DXWKRUL]HG GHDOHU RU VXSSOLHU $GGLWLRQDO VHUYLFH IHHV PD\ DSSO\ LI \RX DUH VHHNLQJ ZDUUDQW\ VHUYLFH IURP D GHDOHU RWKHU WKDQ WKH GHDOHU IURP ZKRP \RX RULJLQDOO\ SXUFKDVHG WKH SURGXFW

&KHFN ZLWK \RXU GHDOHU LQ DGYDQFH IRU DQ\ FRVWV WR \RX ZKHQ DUUDQJLQJ D ZDUUDQW\ FDOO 7UDYHO DQG VKLSSLQJ FKDUJHV IRU SDUWV DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

WARRANTY EXCLUSIONS:

7KLV ZDUUDQW\ GRHV QRW FRYHU WKH IROORZLQJ

&KDQJHV LQ VXUIDFH ILQLVKHV DV D UHVXOW RI QRUPDO XVH $V D KHDWLQJ DSSOLDQFH VRPH FKDQJHV LQ FRORU RI LQWHULRU DQG H[WHULRU VXUIDFH ILQLVKHV PD\ RFFXU 7KLV LV QRW D IODZ DQG LV QRW FRYHUHG XQGHU ZDUUDQW\

'DPDJH WR SULQWHG SODWHG RU HQDPHOHG VXUIDFHV FDXVHG E\ ILQJHUSULQWV DFFLGHQWV PLVXVH VFUDWFKHV PHOWHG LWHPV RU RWKHU H[WHUQDO VRXUFHV DQG UHVLGXHV OHIW RQ WKH SODWHG VXUIDFHV IURP WKH XVH RI DEUDVLYH FOHDQHUV RU SROLVKHV

5HSDLU RU UHSODFHPHQW RI SDUWV WKDW DUH VXEMHFW WR QRUPDO ZHDU DQG WHDU GXULQJ WKH ZDUUDQW\ SHULRG 7KHVH SDUWV LQFOXGH SDLQW ZRRG SHOOHW DQG FRDO JDVNHWV ILUHEULFNV JUDWHV IODPH JXLGHV OLJKW EXOEV EDWWHULHV DQG WKH GLVFRORUDWLRQ RI JODVV

0LQRU H[SDQVLRQ FRQWUDFWLRQ RU PRYHPHQW RI FHUWDLQ SDUWV FDXVLQJ QRLVH 7KHVH FRQGLWLRQV DUH QRUPDO DQG FRPSODLQWV UHODWHG WR WKLV QRLVH DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

'DPDJHV UHVXOWLQJ IURP IDLOXUH WR LQVWDOO RSHUDWH RU PDLQWDLQ WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK WKH LQVWDOODWLRQ

 

LQVWUXFWLRQV RSHUDWLQJ LQVWUXFWLRQV DQG OLVWLQJ DJHQW LGHQWLILFDWLRQ ODEHO IXUQLVKHG ZLWK WKH DSSOLDQFH IDLOXUH WR

 

LQVWDOO WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK ORFDO EXLOGLQJ FRGHV VKLSSLQJ RU LPSURSHU KDQGOLQJ LPSURSHU RSHUD-

 

WLRQ DEXVH PLVXVH FRQWLQXHG RSHUDWLRQ ZLWK GDPDJHG FRUURGHG RU IDLOHG FRPSRQHQWV DFFLGHQW RU LPSURSHUO\

 

LQFRUUHFWO\ SHUIRUPHG UHSDLUV HQYLURQPHQWDO FRQGLWLRQV LQDGHTXDWH YHQWLODWLRQ QHJDWLYH SUHVVXUH RU GUDIWLQJ

 

FDXVHG E\ WLJKWO\ VHDOHG FRQVWUXFWLRQV LQVXIILFLHQW PDNH XS DLU VXSSO\ RU KDQGOLQJ GHYLFHV VXFK DV H[KDXVW IDQV RU

 

IRUFHG DLU IXUQDFHV RU RWKHU VXFK FDXVHV XVH RI IXHOV RWKHU WKDQ WKRVH VSHFLILHG LQ WKH RSHUDWLQJ LQVWUXFWLRQV

 

LQVWDOODWLRQ RU XVH RI FRPSRQHQWV QRW VXSSOLHG ZLWK WKH DSSOLDQFH RU DQ\ RWKHU FRPSRQHQWV QRW H[SUHVVO\ DXWKRUL]HG

 

DQG DSSURYHG E\ ++7 PRGLILFDWLRQ RI WKH DSSOLDQFH QRW H[SUHVVO\ DXWKRUL]HG DQG DSSURYHG E\ ++7 LQ ZULWLQJ

 

DQG RU LQWHUUXSWLRQV RU IOXFWXDWLRQV RI HOHFWULFDO SRZHU VXSSO\ WR WKH DSSOLDQFH

 

1RQ ++7 YHQWLQJ FRPSRQHQWV KHDUWK FRPSRQHQWV RU RWKHU DFFHVVRULHV XVHG LQ FRQMXQFWLRQ ZLWK WKH DSSOLDQFH

 

$Q\ SDUW RI D SUH H[LVWLQJ ILUHSODFH V\VWHP LQ ZKLFK DQ LQVHUW RU D GHFRUDWLYH JDV DSSOLDQFH LV LQVWDOOHG

++7¶V REOLJDWLRQ XQGHU WKLV ZDUUDQW\ GRHV QRW H[WHQG WR WKH DSSOLDQFH¶V FDSDELOLW\ WR KHDW WKH GHVLUHG VSDFH ,QIRUPDWLRQ LV SURYLGHG WR DVVLVW WKH FRQVXPHU DQG WKH GHDOHU LQ VHOHFWLQJ WKH SURSHU DSSOLDQFH IRU WKH DSSOLFDWLRQ &RQVLGHUDWLRQ PXVW EH JLYHQ WR DSSOLDQFH ORFDWLRQ DQG FRQILJXUDWLRQ HQYLURQPHQWDO FRQGLWLRQV LQVXODWLRQ DQG DLU WLJKWQHVV RI

WKH VWUXFWXUH

This warranty is void if:

7KH DSSOLDQFH KDV EHHQ RYHU ILUHG RU RSHUDWHG LQ DWPRVSKHUHV FRQWDPLQDWHG E\ FKORULQH IOXRULQH RU RWKHU GDPDJLQJ FKHPLFDOV 2YHU ILULQJ FDQ EH LGHQWLILHG E\ EXW QRW OLPLWHG WR ZDUSHG SODWHV RU WXEHV UXVW FRORUHG FDVW LURQ EXEEOLQJ FUDFNLQJ DQG GLVFRORUDWLRQ RI VWHHO RU HQDPHO ILQLVKHV

7KH DSSOLDQFH LV VXEMHFWHG WR SURORQJHG SHULRGV RI GDPSQHVV RU FRQGHQVDWLRQ

7KHUH LV DQ\ GDPDJH WR WKH DSSOLDQFH RU RWKHU FRPSRQHQWV GXH WR ZDWHU RU ZHDWKHU GDPDJH ZKLFK LV WKH UHVXOW RI EXW QRW OLPLWHG WR LPSURSHU FKLPQH\ RU YHQWLQJ LQVWDOODWLRQ

LIMITATIONS OF LIABILITY:

7KH RZQHU¶V H[FOXVLYH UHPHG\ DQG ++7¶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

4021-645C12-29-10

Page 2 of 2

6

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

1 Listing and Code Approvals

A. Appliance Certification

MODEL: SLR32

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Vented Gas Fireplace Heater

STANDARD: ANSIZ21.88-2009• CSA2.33-2009

Vented Gas Fireplace Heaters

This product is listed to ANSI standards for “Vented Gas Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Tempered Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

C. BTU Specifications

Models

Maximum

Orifice

(U.S. or Canada)

Input BTU/h

Size (DMS)

 

 

 

 

 

US

20,000

#45

 

(0-2000FT)

SLR32 (NG)

 

 

CANADA

19,000

#46

 

 

(2000-4500FT)

 

 

 

 

 

 

 

 

US

17,500

1.25 mm

SLR32 (LP)

(0-2000FT)

 

 

CANADA

15,750

#56

 

 

(2000-4500FT)

 

 

 

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper orifice size.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

7

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

H.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) in. in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

8

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

2 Operating InstructionsUser Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

Never leave children alone near a hot fireplace, whether operating or cooling down.

Teach children to NEVER touch the fireplace.

Consider not using the fireplace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/safety-information.

To prevent unintended operation when not using your fireplace for an extended period of time (summer months, vacations, trips, etc):

Remove batteries from remote controls.

Turn off wall controls.

Unplug 3 volt adapter plug and remove batteries on IPI models.

WARNING! Choking Hazard! Keep glass rock media out of reach of children.

If you expect that small children or vulnerable adults may come into contact with this fireplace, the following precautions are recommended:

Install a physical barrier such as:

-A decorative firescreen.

-Adjustable safety gate.

B. Your Fireplace

WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire or injury.

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.D.

FIXED GLASS ASSEMBLY

(NOT SHOWN)

SECTION 14.F.

CLEAR SPACE

SECTION 2.C.

Figure 2.1 General Operating Parts

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

9

C. Clear Space

WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2.

Avoid placing candles and other heat-sensitiveobjects on mantel or hearth. Heat may damage these objects.

 

3

 

 

 

 

 

CLEAR

 

 

OF

FT.

 

SPACE

 

IN

 

 

 

 

FRONT

 

 

FIREPLACE

Figure 2.2

Clear Space

 

 

 

D. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

This decorative front has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

E. Fixed Glass Assembly

See Section 14.F.

F.Remote Controls, Wall Controls and Wall Switches

Follow the instructions supplied with the control installed to operate your fireplace:

For safety:

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

See your dealer if you have questions.

G. Before Lighting Fireplace

Before operating this fireplace for the first time, have a qualified service technician:

Verify all shipping materials have been removed from inside and/or underneath the firebox.

Verify that media tray is securely fastened to the base pan.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.

10

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

H. Lighting Instructions (IPI)

The IPI system may be operated with two D-cellbatteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS (IPI)

1.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

3.To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4.If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2.Service technician should turn off electric power to the control when performing service.

593-913G

Final inspection by

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

11

I. After Fireplace is Lit

Initial Break-inProcedure

The fireplace should be run three to four hours continuously on high.

Turn the fireplace off and allow it to completely cool.

Remove fixed glass assembly. See Section 14.F.

Clean fixed glass assembly. See Section 3.

Replace the fixed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the fireplace.

NOTICE! Open windows for air circulation during fireplace break-in.

Some people may be sensitive to smoke and odors.

Smoke detectors may activate.

TO CEILING

120°F

FIREPLACE

 

 

122°F

OPENING

 

 

 

125°F

 

 

 

 

127°F

30

 

129°F

26 28

 

131°F

133°F

24

135°F

22

 

138°F

18

20

 

 

 

 

 

 

14

16

 

 

 

 

 

MEASUREMENTS FROM

TOP EDGE OF FIREPLACE

OPENING

APPLIANCE FRONT

Figure 2.3. Maximum Wall Surface Temperatures Above Fireplace

J. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the fireplace warms, this con-

densation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the fireplace is allowed

to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this fireplace may release an odor for the first several hours. This is caused

Odor from fireplace

by the curing of materials from manufacturing. Odor may also be released from finishing materials

and adhesives used near the fireplace. These circumstances may require additional curing related

 

 

to the installation environment.

 

 

Film on the glass

This is a normal result of the curing process of the paint. Glass should be cleaned within 3 to 4

hours of initial burning. A non-abrasivecleaner such as gas appliance glass cleaner may be nec-

 

 

essary. See your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the

Metallic noise

sound produced by a furnace or heating duct. This noise does not affect the operation or longevity

 

of the fireplace.

 

 

 

There may be some “cracking” noise coming from the fireplace during the first few heating and

 

cooling cycles. This noise is associated with settling rock and some minor cracking of larger

 

pieces of rock. This will lessen over time as the glass rock is conditioned to the heating and cool-

Glass Rock Media

ing temperature changes.

 

It is expected that a few small pieces (approximately 10 pieces) of rock may fall through the base-

 

pan and come to rest on the fireplace bottom. This has no affect on fireplace performance.

 

 

Power Outages

This appliance can operated on battery power in the event of a power outage. To access the bat-

tery pack, the decorative front, mesh and glass assembly must be removed. Refer to Section 12

(battery backup)

for more details.

 

 

 

Wall above appliance feels hot to

No action necessary. This appliance ships with a non-combustiblematerial attached. Specifica-

the touch.

tions of the attached non-combustiblematerial are listed in Section 1.E.

 

 

12

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-freeservice. We recommend annual service by a qualified service technician.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care.

Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

DO NOT clean glass while it is hot

Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.

Remove door or decorative front from fireplace and set aside on work surface.

See Section 14.F for instructions to remove fixed glass assembly.

Clean glass with a non-abrasivecommercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

Refer to Section 14.F for glass removal and replacement instructions.

Reinstall door or decorative front.

Inspect for scratches, dents or other damage and repair as necessary.

Check that louvers are not blocked.

Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote control instructions.

Locate remote control transmitter and receiver.

Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

Place batteries as needed in remote transmitters and battery-poweredreceivers.

Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

Remove batteries from remote controls.

Unplug 3 volt adapter plug on IPI models.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

13

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

Inspect for corrosion or separation.

Verify weather stripping, sealing and flashing remains intact.

Inspect draft shield to verify it is not damaged or missing.

B.Maintenance Tasks-QualifiedService Technician

The following tasks must be performed by a qualified service technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, drop cloth and a stable work surface.

Inspect gasket seal and its condition.

Inspect fixed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

Confirm there is no damage to glass or glass frame. Replace as necessary.

Verify that fixed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Firebox

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, sandpaper, steel wool, cloths, mineral spirits, primer andtouch-uppaint.

Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

Replace fireplace if firebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, dust cloths

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that

have penetrated the sheet metal are sharp and should be avoided.

Remove all foreign objects.

Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer.

Verify burner is properly secured and aligned with pilot or igniter.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or leaking.

Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

Inspect for lifting or other flame problems.

Verify air shutter setting is correct. See Section 14.H for required air shutter setting. Verify air shutter is clear of dust and debris.

Inspect orifice for soot, dirt and corrosion. Verify orifice size is correct. See Service Parts List for proper orifice sizing.

Verify manifold and inlet pressures. Adjust regulator as required.

Inspect pilot flame pattern and strength. See Figure 3.1 for proper pilot flame pattern. Clean or replace orifice spud as necessary.

Inspect IPI flame sensing rod for soot, corrosion and deterioration. Polish with fine steel wool or replace as required.

Verify IPI millivolt output. Replace as necessary.

Verify that there is not a short in flame sense circuit by checking continuity between pilot hood and flame sensing rod. Replace pilot as necessary.

Figure 3.1 IPI Pilot Flame Pattern

14

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

4

Getting Started

Installer Guide

 

 

 

A. Typical Appliance System

NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

HORIZONTAL

VERTICAL TERMINATION CAP

TERMINATION CAP

(SECTION 10.H)

(SECTION 10.K)

 

WALL PENETRATION

 

FRAMING

 

(SECTION 8.B)

 

STORM COLLAR (SECTION 10.G)

NON-COMBUSTIBLEROOFFLASHING MAINTAINS MINIMUM

CLEARANCE AROUND PIPE (SECTION 10.F)

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR

OF ATTIC (SECTION 8.C)

FRAMING/HEADER (SECTION 5)

VENT PIPE PENETRATES

ROOF PREFERABLY

WITHOUT AFFECTING ROOF

RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT

SHOWN) MUST BE USED HERE

TO KEEP INSULATION AWAY

FROM VENT PIPE IF ATTIC IS

INSULATED. (SECTION 8.D)

FRAMING HEADED

OFF IN CEILING

JOISTS (SECTION 8.C)

WALL SWITCH

GAS LINE (SECTION 11)

Figure 4.1 Typical System

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

15

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring requirements.

Framing and finishing details.

Whether optional accessories—devicessuch as a wall switch or remotecontrol—aredesired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

Non-corrosiveleak check solution

Hammer

Phillips screwdriver (magnetic)

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in. magnetic)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Flat blade screwdriver

1/2 - 3/4 in. length, #6 or #8 Self-drillingscrews

Caulking material (300ºF minimum continuous exposure rating)

D. Inspect Appliance and Components

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

16

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

It is important to follow the framing and finishing instructions step by step to ensure proper placement of fireplace in the surrounding framing/finishing materials.

Unlike many traditional, single sided Heat & Glo fireplaces, the SLR32 is recessed into surrounding framing. The left and right nailing tabs were designed to ensure the fireplace is recessed to the correct location within the framing materials. Refer to Section 13 for detailed instructions on finishing.

A

E

1 IN.

D*

 

A

ALCOVE

B

INSTALLATION

C

TOP VENT

 

ONE 900 ELBOW

TOP VENT

ONE 90° ELBOW

B

F

 

 

A

 

B

C

D

 

E

F

 

 

Inches

46-3/4

 

37-5/8

63-1/8

See Section D.

 

15-1/16

18-3/4

 

 

 

Millimeters

1188

 

956

1603

Figure 5.5 & 5.6

 

383

476

 

 

Figure 5.1 Appliance Locations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

17

B. Constructing the Appliance Chase

A chase is a vertical box-likestructure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase.

NOTICE: Treatment of ceiling firestops and wall shield firestops and construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with caulk with a minimum of 300ºF continuous exposure rating to seal gaps. Gas line holes and other openings should be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with unfaced insulation. If the appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

The factory-suppliednon-combustibleboard must be used in all installations. It must be directly attached to structural framing adjacent to the appliance. Screw fasteners should be installed in the pilot holes provided in the outer perimeter of thenon-combustibleboard. See Figure 13.3.

The factory-suppliedboard is designed such that its edges will be at the approximate center of the adjacent framing, assuming it is1-1/2in. nominal thickness. This will allow the wallboard joints to occur on the center of the framing where the panels can be fastened properly. If the framing thickness is less than1-1/2in. nominal, such as with formed steel systems, then it may be necessary to adjust the adjacent framing dimensions so that the noncombustible board and wallboard joints are centered on the framing.

18

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth.DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specified air space clearances to appliance and vent pipe:

Insulation and other materials must be secured to prevent accidental contact.

The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fireplace or chimney.

Failure to maintain airspace may cause overheating and a fire.

Note: Figure 5.2 shows the fireplace installed on the floor. However, this fireplace can be elevated off the floor provided that the fireplace is properly supported by framing materials and the ceiling clearances are maintained.

MEASURE FROM TOP

OF FIREPLACE OPENING

A

E

 

 

 

 

 

 

F

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J

 

 

 

 

 

 

C

 

 

 

 

G

 

 

H

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

MINIMUM FRAMING DIMENSIONS*

 

 

 

 

A

B

C

D

E

F

G

H

I

J

 

Rough

Rough

Rough

Rough

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

Opening

Opening

Opening

Opening

 

to Ceiling

Floor

Flooring

Appliance

Appliance

Appliance

 

(Vent Pipe)

(Height)

(Depth)

(Width)

 

 

 

 

 

 

 

Inches

8-5/8

36-1/2

18-1/4

37-3/4

31

0

0

1

1/2

36

Millimeters

219

927

464

959

787

0

0

25

13

914

Figure 5.2. Clearances to Combustibles

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

19

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantels

Combustible Mantel Legs Or Wall Projections Extending Past The Face Of The Fireplace

1/2 in.

Thick Wall

Sheathing 12 in.MAX.

14 in. MEASUREMENT FROM TOP OF MIN. FIREPLACE OPENING

Figure 5.3 Clearances To Combustible Mantels Or Other Combustibles Above Appliance

Non-combustibleMantels

 

1/2 IN.

 

 

Thick Wall

12 IN.

 

Sheathing

 

MAX.

 

 

 

 

14 IN.

 

 

MIN.

 

MEASUREMENT

 

 

FROM TOP OF

 

 

FIREPLACE

 

 

OPENING

1 IN.MIN.

 

 

 

 

4 IN.

 

 

MAX.

Figure 5.4

Clearances To Non-CombustibleMantels Or Other

 

Non-CombustiblesAbove Appliance

Note: Fornon-combustiblefireplace finish material (marble, stone, etc) specifications refer to Section 13.C.

20

Heat & Glo • SLR32 •

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 IN.

 

 

3

 

 

 

FIREPLACE

 

MINIMUM

 

 

 

FT. MAXIMUM

OPENING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 IN.

 

 

 

 

 

 

 

 

 

MINIMUM

Figure 5.5 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Non-combustibleMantel Legs Or Wall Projections Extending Past The Face Of The Fireplace

3 IN.

FIREPLACE MINIMUM UNLIMITED OPENING

7 IN.

Figure 5.6 Non-CombustibleMantel Leg or Wall Projections (Acceptable on both sides of opening)

Front Side Finishing Detail

 

1/2 IN.

 

FRAMING

 

NAILING TAB

 

1/2 IN. FACTORY-SUPPLIED

 

NON-COMBUSTIBLEBOARD

Figure 5.7

Front Side Finishing Detail

2269-900Rev. E • 4/12

 

1/2 IN. THICK

5 IN.

WALL

SHEATHING

 

 

NON-COMBUSTIBLE

 

BOARD SHIPPED

1 IN.

WITH APPLIANCE

 

1 IN.AIR SPACE

Figure 5.8 Non-CombustibleZone

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

21

6 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Maintain vent clearance to combustibles as specified.

DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and fire.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12.................................................1.25*

Over 7/12 to 8/12.................................................1.5*

Over 8/12 to 9/12.................................................2.0*

Over 9/12 to 10/12...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12.............................................5.0

Over 14/12 to 16/12.............................................6.0

Over 16/12 to 18/12.............................................7.0

Over 18/12 to 20/12.............................................7.5

Over 20/12 to 21/12.............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge

Opening

 

 

22

 

Heat & Glo • SLR32 •

A

B

6 in. (minimum) up to 20 in.

18 in. minimum

152 mm/508 mm

457 mm

20 in. and over

0 in. minimum

Gas, Wood or Fuel Oil

Termination Cap

B

A *

Gas

Termination

Cap **

*If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

**In a staggered installation with both gas and wood or fuel oil terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Figure 6.2 Staggered Termination Caps

2269-900Rev. E • 4/12

 

 

 

 

 

 

 

 

 

 

 

O

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

C

 

 

 

F

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

Q

 

J

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

H or i

 

 

 

 

 

 

 

V

 

B

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

D

X

V

 

E

 

 

V

 

 

 

 

G

 

 

 

 

 

 

 

V

 

H

 

 

 

 

 

 

 

 

 

V

M

 

 

V

 

 

 

 

 

 

 

 

V

V

H V

 

 

L

 

 

 

 

 

 

A

A

 

 

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

 

 

 

 

V

Electrical

K

V

 

V

 

 

 

 

 

 

 

 

= VENT TERMINAL

 

 

 

 

 

 

 

Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X = AIR SUPPLY INLET

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

A

=

12 inches.................

clearances above grade, veranda,

 

 

 

 

porch, deck or balcony

B

=

9 inches...................

clearance to window or door that may

 

 

 

 

be opened, or to permanently closed

 

 

 

 

window

C

=

18 inches.................

clearance below unventilated soffit

 

 

18 inches.................

clearance below ventilated soffit

 

 

30 inches .................

clearance below vinyl soffits and

 

 

 

 

electrical service

D

=

6 inches...................

clearance to outside corner

E

=

6 inches...................

clearance to inside corner

F

=

3 ft. (Canada)..........

not to be installed above a gas me-

 

 

 

 

ter/regulator assembly within 3 feet

 

 

 

 

horizontally from the center-lineof the

 

 

 

 

regulator

G

=

3 ft...........................

clearance to gas service regulator

 

 

 

 

vent outlet

H

=

12 inches.................

clearance to non-mechanical(unpow-

 

 

 

 

ered) air supply inlet, combustion air

i

=

3 ft. (U.S.A.)

inlet or direct-venttermination

 

 

 

6 ft. (Canada)...........

clearance to a mechanical (powered)

 

 

 

 

air supply inlet

All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below termination.

J

= 7 ft..........................

On public property: clearance above

 

 

paved sidewalk or a paved driveway.

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

K

=

6 inches.................

clearance from sides of electrical

 

 

 

service

L

=

12 inches................

clearance above electrical service

Location of the vent termination must not interfere with access to the electrical service.

M = 18 inches ....................

clearanceunderveranda,porch,deck,

 

balcony or overhang

42 inches ................

vinyl or composite overhang

Permitted when veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor.

C

V

Covered Alcove Applications

(Spaces open only on one side and with an overhang)

N= 6 inches ........... non-vinylsidewalls 12 inches ......... vinyl sidewalls

O= 18 inches ......... non-vinylsoffit and overhang 42 inches ......... vinyl soffit and overhang

P= 8 ft.

 

QMIN

RMAX

1 cap

3 feet

2 x Q ACTUAL

2 caps

6 feet

1 x Q ACTUAL

3 caps

9 feet

2/3 x Q ACTUAL

4 caps

12 feet

1/2 x Q ACTUAL

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

CAUTION! Risk of Burns! Termination caps are HOT, consider proximity to doors, traffic areas or where people maypass or gather (sidewalk, deck, patio, etc.). Listed cap shields available. Contact your dealer.

Local codes or regulations may require different clearances.

Vent system termination is NOT permitted in screened porches.

Vent system termination is permitted in porch areas with two or more sides open.

Hearth & Home Technologies assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

• Vinyl protection kits are suggested for use with vinyl siding.

Figure 6.3 Minimum Clearances for Termination Heat & Glo • SLR32 • 2269-900 Rev. E • 4/12

23

7 Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home Technologies SLP venting systems. Refer to Section 16.B for vent component information.

DO NOT mix pipe, fittings or joining methods from different manufacturers.

The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOTvent to a pipe serving a separate solid fuel burning appliance.

B. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

 

 

V1

First section (closest to appliance) of vertical length

 

 

V2

Second section of vertical length

 

 

H1

First section (closest to appliance) of horizontal length

 

 

H2

Subsequent sections of horizontal length

 

 

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2in. (216 mm) horizontal run and8-1/2in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1).

Vertical

 

in.

 

 

 

 

.

 

 

1/2-8

 

12

in

 

 

8-1/2in.

Horizontal

Figure 7.1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

Pipe measurements are shown using the effective length of pipe (see Figure 7.2).

Measurements are made from the appliance outer wrap, not from the standoffs.

Horizontal terminations are measured to the outside mounting surface (flange of termination cap).

Vertical terminations are measured to bottom of termination cap.

Horizontal pipe installed level with no rise.

A

B

1-1/4in. (32 mm)

OVERLAP

Figure 7.2 Chimney Offset/Return

 

Effective Height/Length

 

Pipe

inches

mm

 

SLP4

4

102

Effective

SLP6

6

152

SLP12

12

305

Height/

SLP24

24

610

Length

SLP36

36

914

 

 

SLP48

48

1219

 

SLP6A

2 - 6

51 - 152

 

SLP12A

2 - 12

51 - 305

Figure 7.3 SLP Pipe Effective Length

E. Vent Diagrams

General Rules:

When penetrating a combustible wall, a wall shield firestop must be installed.

When penetrating a combustible ceiling, a ceiling firestop must be installed.

Horizontal runs of vent do not require vertical rise; horizontal runs may be level.

24

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

WARNING

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between ceiling firestops.

ALWAYS maintain specified clearances around venting and firestop systems.

Install wall shield and ceiling firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

Top Vent - Horizontal Termination

Venting with 1 elbow

V Minimum

H1 Maximum

SLR32

 

 

 

 

 

 

90 Elbow

1-1/2ft.

457 mm

 

 

 

 

1 ft.

305 mm

3 ft.

914 mm

 

 

 

 

2 ft.

610 mm

5 ft.

1.5 m

 

 

 

 

3 ft.

914 mm

7 ft.

2.1 m

 

 

 

 

4 ft.

1.2 m

14 ft.

4.3 m

 

 

 

 

H MAX. =14 ft. (4.3 m)

V + H MAX. = 40 ft. (12.2 m)

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

V1

H1

Figure 7.4

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

25

1. Top Vent - Horizontal Termination - (continued)

Top Vent - Horizontal Termination

Venting with 2 elbows

 

V Minimum

H1 + H2 MAXIMUM

 

 

SLR32

 

 

 

 

 

90° Elbow

1 ft.

 

305 mm

 

 

 

 

 

 

1 ft.

 

305 mm

2 ft.

 

610 mm

 

 

 

 

 

 

2 ft.

 

610 mm

4 ft.

 

1.2 m

 

 

 

 

 

 

3 ft.

 

914 mm

6 ft.

 

1.8 m

 

 

 

 

 

 

4 ft.

 

1.2 m

15 ft.

 

4.6 m

 

 

 

 

 

 

H + H1 MAX. =15 ft. (4.6 m)

V + H + H1 MAX. = 40 ft. (12.2 m)

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

H2

V1

H1

 

INSTALLED

HORIZONTALLY

Figure 7.5

26

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

1. Top Vent - Horizontal Termination - (continued)

 

 

 

 

 

 

Top Vent - Horizontal Termination

 

 

 

 

 

 

 

Venting with 3 elbows

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLR32

 

 

 

V1 Minimum

H1 + H2 Maximum

V2

V1 + V2 Minimum

 

90° Elbow

6 ft.

 

 

 

1.8 m

*

*

 

1 ft.

305 mm

10 ft.

 

 

 

3.0 m

*

*

 

2 ft.

610 mm

12 ft.

 

 

 

3.7 m

*

*

 

3 ft.

914 mm

14 ft.

 

 

 

4.3 m

*

*

 

 

 

H1

+ H2

MAX. =14 ft. (4.3 m)

 

 

 

 

V1 + V2 + H1

+ H2 MAX. = 40 ft. (12.2 m)

 

 

*No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)

 

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

H2

V2

H1V1

Figure 7.6

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

27

Top Vent - Vertical Termination

No Elbows

V1 = 44 ft. Max. (13.4 m)

Note: If installing a vertical vent/termination off the top of the appliance, the optional exhaust restrictor may be needed.

Note: Use SLP Series components only.

V1

Figure 7.7 Vertical Vent Maximum

Exhaust restrictors are recommended for these vertically terminated products which have excessive draft. Exhaust restrictors will compensate for high draft, and restore visual flame height. If the vent configuration has a total vertical of 15-44feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance manual bag.

Exhaust restrictor Instructions

1.Locate the two pilot holes located in the inside firebox heat shield as shown in Figure 7.8.

2.Center the exhaust restrictor such that the through holes in the vent restrictor align with the pilot holes in the restrictor.

3.Use two 1/2 in. self-piercingscrews to secure vent restrictor to firebox heat shield. See Figure 7.9.

PILOT HOLES

Figure 7.8 Location of Pilot Holes

Figure 7.9 Exhaust Restrictor Installation

4.In some applications, such as those where the fireplace is elevated off the floor, the vent restrictor may be painted, but painting is not required.

NOTICE: Before painting, contact your dealer for information on the appropriate high temperature paint.

28

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

Top Vent - Vertical Termination

Venting with 2 elbows

SLR32

V1 Minimum

H Maximum

V2

V1 + V2 Minimum

 

90° Elbow

2 ft.

610 mm

*

*

1 ft,

 

152 mm

3 ft.

914 mm

*

*

2 ft.

 

457 mm

5 ft.

1.5 m

*

*

3 ft.

 

914 mm

7 ft.

2.1 m

*

*

4 ft.

 

1.1 m

15 ft.

4.6 m

*

*

H MAX. =15 ft. (4.6 m)

V1 + V2 + H MAX. = 40 ft. (12.2 m)

* No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

V2

V1

H1

Figure 7.10

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

29

Top Vent - Vertical Termination

Venting with 3 elbows

SLR32

 

V1 Minimum

H1 + H2 Maximum

V2

V1 + V2 Minimum

 

90° Elbow

1 ft.

305 mm

*

*

1 ft.

 

305 mm

2 ft.

610 mm

*

*

2 ft.

 

610 mm

4 ft.

1.2 m

*

*

3 ft.

 

914 mm

6 ft.

1.8 m

*

*

4 ft.

 

1.2 m

14 ft.

4.3 m

*

*

H MAX. =14 ft. (4.3 m)

V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)

* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)

 

 

Note: Use SLP Series

 

 

 

components only.

 

 

 

 

 

 

 

 

 

 

 

 

Note: ThereMUST be a 25%

 

 

reduction in total H when using

 

 

flex vent except when using the

V2

simple up and out installation

 

 

 

 

(see Figure 7.3).

 

 

 

 

 

 

 

 

H1

H2

V1

 

 

INSTALLED

 

HORIZONTALLY

Figure 7.11

30

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

Top Vent - Vertical Termination

Venting with 4 elbows

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 5.3).

V1 MIN.

 

H1 MAX.

V2 MIN.

H2 MAX.

V3 MIN.

 

 

 

 

 

 

 

 

 

 

 

1-1/2ft.

457 mm

 

4 ft.

1.2 m

4 ft.

1.2 m

4 ft.

1.2 m

3-1/2ft.

1.0 m

 

 

 

 

 

 

 

 

 

 

 

 

 

V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)

 

 

V3

V2

H2

H1

V1

Figure 7.12

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

31

Coaxial to Colinear Venting

The coaxial to colinear adapter (DV-46DVA-GCL)is approved for installations into solid fuel masonry or factory built fireplaces that have been installed in accordance with the National, Provincial, State and local building codes. TheDV-46DVA-GCLmust be recessed into existing masonry fireplace. See Table 1 and Figure 7.14.

INLET AIR VENT PIPE

EXHAUST VENT PIPE

Figure 7.13 Coaxial/Colinear Appliance Adapter (DV-46DVA-GCL)

WARNING! Risk of Fire! Coaxial to colinear venting configuration may only be used in existingnon-combus-tible chimney. Installation in any other venting application could cause fire.

Prior to installing the gas appliance:

Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

Replace component parts of the chimney and fireplace as specified by the professionals.

Ensure all joints are properly engaged and the chimney is properly secured.

Table 1

CLEARANCE TO COMBUSTIBLES REQUIREMENTS

DV-46DVA-GCL

3 IN.

Exhaust Vent Pipe

5 IN.

OUTSIDE FACE OF

FIREPLACE

EXHAUST VENT PIPE

TOP OF FIREPLACE

OPENING

5 IN. MIN.

3 IN. MIN.

SHADED AREA DEFINED AS

“INSIDE EXISTING MASONRY FIREPLACE”

Figure 7.14 Existing Fireplace DV-46DVA-GCLClearance

Requirements

Clearances to Combustibles:

Refer to Section 5 for clearances to the appliance, mantel, mantel legs and wall projection.

Refer to Section 8 for pipe clearances to combustibles.

Termination Cap

For installation of termination cap see minimum vent heights for various pitched roofs. See Section 6 of appliance owner’s manual.

Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open position, OR completely remove it.

Venting Components

The LINK-DV30Bis approved for use with the coaxial/colinear venting application. TheLINK-DV30Bkit includes:

Two 30 feet sections of flexible vent pipe (3 inches Ø). One section is used to draw combustion air and the other section is used to expel exhaust gases.

One vertical termination cap.

CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCLadapter andLINK-DV30Bkit.This may result in poor flame appearance, sooting, pilot malfunction, or overheating.

32

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

Connecting the DV-46DVA-GCLAdapter to Appliance Top Vent

Remove top seal cap and insulation if equipped. See Section 14, “Appliance Setup.” Attach the DV-46DVA-GCL adapter to the appliance starting collar with3-1/2in.self-tappingscrews. See Figure 7.15.

Connecting the LINK-DV30Bto theDV-46DVA-GCLadapter

Insert the two sections of flexible vent pipe down the existing chimney.

Attach one section of flexible vent pipe to the exhaust collar on top of the DV-46DVA-GCLadapter with threeself-tappingscrews.

Attach one section of flexible vent pipe to the inlet collar on top of the DV-46DVA-GCLadapter with three selftapping screws.

To minimize cold air drafts, seal around the flex vents at the damper inside the chimney with non-combustibleunfaced fiberglass or rock wool insulation.

The DV-46DVA-GCLadapter must be recessed into existing masonry fireplace. This measurement is taken from the top of the fireplace opening. See Table 1 and Figure 7.14.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Do NOT connect this gas appliance to a chimney flue serving a separate solid fuel or gas burning appliance.

May impair safe operation of this appliance or other appliances connected to the flue.

Vent this appliance directly outside.

Use separate vent system for this appliance.

CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCLadapter andLINK-DV30Bkit.This may result in poor flame appearance, sooting, pilot malfunction, or overheating.

TOP VENT

TERMINATION CAP

NOTICE: To achieve optimum per-

 

 

formance of appliance, minimize or

 

 

avoid bends in exhaust vent pipe.

 

 

 

 

 

 

V

 

 

EXISTING CHIMNEY

 

 

 

EXHAUST AIR

 

 

 

 

VENT PIPE

INLET AIR

 

 

 

 

VENT PIPE

 

 

EXISTING CHIMNEY

 

 

 

 

 

To minimize cold air

 

 

 

 

drafts, seal with

 

 

 

 

non-combustible

 

 

 

 

insulation.

 

V

DIRECT VENT FIREPLACE

 

Minimum

10 ft.

3.05 m

 

 

Maximum

40 ft.

12.2 m

 

 

 

 

FLOOR

HEARTH

 

 

 

 

 

Figure 7.15

 

 

 

 

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

33

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent.DO NOT pack insulation or other combustibles:

Between ceiling firestops

Between wall shield firestops

Around vent system

Failure to keep insulation or other material away from vent pipe may cause over heating and fire.

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).

SLP heat shield - designed to be used on a wall4-3/8in. to7-5/8in. (111 mm to 194 mm thick).

,I ZDOO WKLFNQHVV LV OHVV WKDQ WKH H[LVWLQJ KHDW VKLHOGV PXVW EH ILHOG WULPPHG ,I ZDOO WKLFNQHVV LV JUHDWHU WKDQ LQ D '93 +60 % ZLOO EH UHTXLUHG

 

(SLP Pipe Shown)

 

 

Heat

3 in. (76 mm)

3 in. (76 mm)

Shield

top clearance *

top clearance

 

Heat

 

 

Shield

1 in. (25 mm)

 

 

clearance around

 

 

vertical sections

 

 

 

 

1 in. (25 mm)

 

Wall

clearance

 

Shield

bottom & sides

 

Firestop

 

 

WALL

 

* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are: Top: 2-1/2in. (64 mm)

Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm)

Figure 8.1 Horizontal Venting Clearances To Combustible

Materials

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield firestop(s). The wall shield firestop maintains minimum clearances and prevents cold air infiltration.

The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.

SLP pipe - A wall shield firestop must be placed on each side of an interior wall. A minimum 1-1/2in. (38 mm) overlap of attached heat shields must be maintained.

See Section 10.K. for information for regarding the installation of a horizontal termination cap.

Non-CombustibleWall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one in. greater than the pipe is acceptable.

Whenever a non-combustiblewall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.

DO NOT PACK WITH

INSULATION OR

OTHER MATERIAL

10 in. 10 in.

B

A

A*

B

40-3/4in.

39-3/4

1035 mm

1010mm

*Shows center of vent framing hole for top venting. The center of the hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.

Figure 8.2 Wall Penetration

34

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

C. Install the Ceiling Firestop

A ceiling firestop MUST be used between floors and attics.

SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.3).

Frame the area with the same sized lumber as used in ceiling/floor joist.

The ceiling firestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between floors that are not insulated. Refer to Figure 8.4.

Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu- lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

 

 

ATTIC ABOVE

 

 

A

 

 

A

 

PIPE

A

 

SLP

9 in. (229 mm)

Figure 8.3

Installing Ceiling Firestop

 

INSTALL ATTIC INSULATION SHIELDS

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

3 FASTENERS

 

PER SIDE

 

CEILING FIRESTOP

CEILING FIRESTOP

INSTALLED BELOW CEILING

INSTALLED ABOVE CEILING

Figure 8.4 Installing the Attic Shield

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

35

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specified clearance and be secured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Vaulted Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Cut the attic insulation shield (if application is for vaulted ceiling) to fit your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90°

TO MAINTAIN CLEARANCE

AND PREVENT INSULATION

FROM FALLING INSIDE

BEND 3 TABS

OUTWARD TO

FASTEN TO CEILING

FIRESTOP-BEND

REMAINING TABS

INWARD 90 DEGREES

TO MAINTAIN

INSERT 3 CLEARANCE

SCREWS

Figure 8.5 Attic Insulation Shield

36

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

9 Appliance Preparation

A. Preparing Elbow Heat Shield

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

ELBOW HEAT SHIELD

SHOWN AS INSTALLED

Figure 9.1 Elbow Shield Shown Installed

If venting with a 90 degree elbow directly off of the top of the appliance, the elbow heat shield must be repositioned as shown in Figure 9.1.

If venting vertically or using a straight section of vertical pipe, remove the elbow heat shield and discard by removing the two 1/4 in. screws that secure the elbow heat shield to the top of the fireplace.

For all venting applications, ensure that the pipe gasket is in place before attaching any pipe section. This gasket is shipped in place around the starting collar. See Figure 9.1.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

37

B. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

Sagging or loose insulation

Insulation backing or plastic

Framing and other combustible materials

Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs. Failure to maintain air space clearance may cause overheating and fire.

For details on setting the appliance in the framing, refer to section 13.A. The diagram shows how to properly position, level, and secure the appliance (see Figure 9.2). Nailing tabs are provided to secure the appliance to the framing members.

Bend out nailing tabs on each side.

Place the appliance into position.

Keep nailing tabs flush with the framing.

Level the appliance from side to side and front to back.

Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

Secure the appliance to the framing by using nails or screws through the nailing tabs.

Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

Figure 9.2 shows the fireplace installed on the floor. However, this fireplace can be elevated off the floor provided that the fireplace is properly supported by framing materials and the ceiling clearances are maintained.

NAILING TABS

BOTH SIDES

Figure 9.2 Proper Positioning, Leveling and Securing of an

Appliance

38

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

10 Installing Vent Pipe (SLP Pipe)

A. Assemble Vent Sections

To attach the first vent component to the starting collars of the appliance:

Lock the vent components into place by sliding the pipe section onto the collar.

Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 10.1.

Slide the gasket over the first vent section and place it flush to the appliance. This will prevent cold air infiltration. Caulk with a minimum of 300ºF continuous exposure rating may be used to hold the part in place.

Continue adding vent components, locking each succeeding component into place.

Ensure that each succeeding vent component is securely fitted and locked into the preceding component.

Commercial, Multi-family(Multi-levelexceeding two stories), orHigh-RiseApplications

For Installation into a commercial, multi-family(multi-levelexceeding two stories) orhigh-riseapplications: All outer pipe joints must be sealed with silicone with a minimum of 300ºF continuous exposure rating, including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 10.2

Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 10.1 Adding Venting Components

Figure 10.2 High Temperature Silicone Sealant

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

39

B. Assemble Slip Sections

Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 10.3.

Slide together to the desired length.

Pilot hole

Figure 10.3 Slip Section Pilot Holes

Maintain a 1-1/2in. (38 mm) overlap between the slip section and the pipe section.

Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 10.4.

Figure 10.4 Screws into Slip Section

Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a silicone sealant with a minimum of 300ºF continuous exposure rating.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

Only outer pipes are sealed, sealing the inner flue is not required.

All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed.

C. Secure The Vent Sections

Vertical runs of pipe must be supported every 8 ft. (2.44 m).

Horizontal sections must be supported every 5 feet (1.52 m).

Vent supports or plumbers strap (spaced 120º apart) may be used to support. See figures 10.5 and 10.6.

Wall shield firestops may be used to provide horizontal support.

Ceiling firestops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

Figure 10.5 Securing Vertical Pipe Sections

Figure 10.6 Securing Horizontal Pipe Sections

40

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

D. Disassemble Vent Sections

Rotate either section (see Figure 10.7) so the seams on both pipe sections are aligned as shown in Figure 10.8.

Pull carefully to separate the pieces of pipe.

Figure 10.7 Rotate Seams for Disassembly

Figure 10.8 Align and Disassemble Vent Sections

E. Install Decorative Ceiling Components

A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling thimble is used to cover the firestop.

Seal the gap between the vent pipe and firestop using silicone with a minimum of 300ºF continuous exposure rating to prevent cold air infiltration.

Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.

A decorative cathedral ceiling support box can be installed on a cathedral ceiling through which the vent passes.

Use a plumb-bobto mark the center line of the venting system on the ceiling and drill a small hole through the ceiling and roof at this point. Locate the hole and mark the outline of the cathedral ceiling support box on the outside roof.

Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure

10.9).

Level the support box both vertically and horizontally and temporarily tack it in place through the inside walls into the roof sheathing.

Use tin snips to cut the support box from the top corners down to the roof line and fold the resulting flaps to the roof. See Figure 10.10.

Nail the flaps to the roof AFTER running a bead of non hardening sealant between the flaps and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

LEVEL

CATHEDRAL CEILING

SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm)

GREATER IN SIZE THAN

PATTERN OF SUPPORT

BOX AS IT IS PROJECTED

ONTO ROOF LINE

Figure 10.9

Figure 10.10

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

41

F. Install Metal Roof Flashing

See minimum vent heights for various pitched roofs (Figure 10.11) to determine the length of pipe to extend through the roof.

Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 10.12.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12............................1.25*

Over 7/12 to 8/12..............................1.5*

Over 8/12 to 9/12..............................2.0*

Over 9/12 to 10/12............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12........................... 5.0

Over 14/12 to 16/12........................... 6.0

Over 16/12 to 18/12........................... 7.0

Over 18/12 to 20/12........................... 7.5

Over 20/12 to 21/12........................... 8.0

* 3 foot minimum in snow regions

Figure 10.11 Minimum Height From Roof To Lowest Discharge

Opening

 

 

NOTICE: Failure to properly caulk the roof flashing and pipe seams may permit entry of water.

Caulk the gap between the roof flashing and the outside diameter of the pipe.

Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 10.12.

Caulk the overlap seam of any exposed pipe sections that are located above the roof line.

CAULK

Figure 10.12

G. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Connect both halves of the storm collar with two screws (see Figure 10.13).

Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 10.14).

Caulk around the top of the storm collar (see Figure 10.15).

Figure 10.13 Assembling the Storm Collar

Figure 10.14 Assembling the Storm Collar Around the Pipe

42

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

H. Install Vertical Termination Cap

Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

Secure the cap by driving three self-tappingscrews (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 10.15).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 10.15

I. Install Decorative Wall Components

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the firestop.

Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 10.16.

J.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.

DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 10.17).

Heat shields must overlap 1-1/2in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attachedto the wall shield firestop. The other section isfactory-attachedto the cap. See Figure 10.17.

If the wall thickness does not allow the required 1-1/2in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

If the wall thickness is less than 4 in./102 mm (DVP) or 4-3/8in./ 111 mm (SLP), the heat shields on the cap and wall shield firestop must be trimmed. A minimum1-1/2in. (38 mm) overlap MUST be maintained.

Use an extended heat shield if the finished wall thickness is greater than 7-1/4in. (184 mm).

The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2in. (38 mm) overlap between heat shields.

Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields maynot be field constructed.

Figure 10.16 Wall Thimble

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

43

K. Install Horizontal Termination Cap

WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent.

1-1/2(38 mm) minimum overlap of flue telescoping section is required.

Failure to maintain overlap may cause overheating and fire.

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at outside edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current

ANSI Z223.1 and CAN/CGA-B149installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

NOTICE: For certain exposures which require superior resistance towind-drivenrain penetration, a flashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps withfactory-suppliedheat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

HEAT SHIELD

EXTENDED

1-1/2IN. (38 MM) MIN.

HEAT SHIELD

OVERLAP

WALL SHIELD

 

FIRESTOP

 

SLIP SECTION

 

CAN BE EXTENDED

 

INNER VENT

SHEATHING

OUTER VENT

 

INTERIOR

EXTERIOR

Figure 10.17 Venting through the wall

 

44

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

11 Gas Information

A. Fuel Conversion

Make sure the appliance is compatible with available gas types.

Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressure

Optimum appliance performance requires proper input pressures.

Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

Pressure requirements are:

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

8.0 in. w.c.

Maximum inlet pressure

10.0 in. w.c.

13.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: This appliance does include a manual gas shutoff valve that is located in the valve compartment. This manual gas shutoff valve is accessible for service by removing the base pan, burner assembly and valve plate. See Figure 11.1.

The lower access cover panel is removable if finishing material has not been previously installed.

Access Through the Valve Assembly

The lower access cover panel is removable if finishing material has not been previously installed.

Remove Media Tray, Burner Assembly, and Base pan. To access components:

1.Remove eleven screws around perimeter of valve plate as well as valve bracket screw. See Figure 11.2 and Figure 11.5.

2.Lift the valve plate from the back so that the gas valve can clear the valve plate hole in the bottom the firebox. See Figure 11.3.

BURNER SCREWS

MESH SCREWS

Figure 11.1 Cover Tray Removal

Figure 11.2. Remove Valve Plate Screws

3.Set the valve bracket on the front lip of the firebox bottom. Turn “off” the ball valve. Disconnect gas valve from the gas flex ball valve assembly at the pressure fitting. See Figure 11.4.

Figure 11.3. Remove Valve Plate

4.Lift the valve assembly up and out to make necessary service or repair.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

45

Figure 11.4. Disconnect Gas Valve

Note: Install the gas supply line in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Valve Pressure Taps

The pressure taps are accessible through the front of the appliance. The decorative mesh front and fireplace gas assembly must be removed to gain access to the pressure taps. See Figure 11.5.

PRESSURE TAPS

VALVE BRACKET SCREW

Figure 11.5 Valve Pressure Taps and Remote Receiver Location

Note: The manifold and inlet pressure tabs can be accessed from the front of the fireplace when valve assembly is installed.

C. Gas Connection

Refer to Reference Section 16 for location of gas line access in appliance.

Gas line may be run through knockout(s) provided.

The gap between supply piping and gas access hole may be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with non-combustible,unfaced insulation to prevent cold air infiltration.

Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

Pipe incoming gas line into valve compartment.

Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.

Purge should be performed by qualified service technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all fittings and connections with a non-corrosivecommercially availableleak-checksolution.DO NOT use open flame. Fittings and connections could have loosened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce burner orifice 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce burner orifice 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

46

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric

Code CSA C22.1.

Wire the appliance junction box to 110-120VAC. This is required for use of optional accessories (standing pilot ignition) or proper operation of the appliance (IntelliFire ignition).

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

B. IntelliFire Ignition System Wiring

Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figure 12.2, IntelliFire Pilot Ignition (IPI) Wiring Diagram.

This appliance is equipped with an IntelliFire control valve which operates on a 3 volt system.

Plug the 3-voltAC transformer into the appliance junction

box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

C. Optional Accessories Requirements

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

NOTE: Install optional remote receiver adjacent to battery pack.

Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

Optional Remote Control Receiver and Battery Pack Location

Batteries are to be installed only when battery power is required. Because of the limited accessibility to valve cavity, the position of the battery pack, IPI control module, and optional remote control receiver locations must be installed as shown in Figure 12.1.

The battery pack, control module, and remote control receiver can be accessed through the air space between the firebox front and the lower-frontfinishing cover panel. The decorative front and glass assembly must be removed to access these components.

The battery pack is attached with velcro to the inside of the lower cover panel. The IPI control module and the remote control receiver are placed on the firebox bottom.

DC ADAPTER JUNCTION BOX

THERMOSTAT WIRE

 

CONTROL MODULE

 

 

BATTERY PACK

VALVE

 

 

(LOCATED INSIDE BOTTOM COVER

 

 

PANEL)

 

 

 

Figure 12.1 Valve Cavity

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

47

HOT

NEUTRAL

BATTERY PACK

IGNITION MODULE 3 VAC

INTERMITTENT PILOT IGNITOR

TRANSFORMER

 

3 VAC

 

PLUG IN

BLACK

 

RED

THERMOSTAT

WIRE ASSEMBLY

I

S

WHITE

ORANGE

GROUND TO

FIREPLACE

CHASSIS

WIRES

 

(TO BROWN)

 

ORANGE

GREEN

 

NOTE: 1. Ignition module, valve, pilot, and

VALVE

wall switch operate on 3 volts. 120 VAC is

required at junction box unless equipped

 

 

with battery back-up.

Figure 12.2 IntelliFire Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

E. Junction Box Installation

1.Bend junction box heat shield to the right along the perforated hand bends.

2.Remove the one screw located in front of the junction box.

3.Remove the plastic electrical knockout slug in the top of the junction box.

4.Install wire strain (not included) and route wire through wire strain fitting.

5.Make the connections inside the junction box to the 120V wire. Connect the green wire to the ground nut, the black wire to the black wire and the white wire to the white wire.

6.Reinstall the junction box.

7.Reposition the junction box heat shield such that it is positioned over the junction box.

Note: There is an alternative access to the junction box. This can be accessed by removing the valve assembly. See Section 11.

48

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

13 Finishing

A. Framing and Finishing Instructions

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.)

Finishing Instructions

It is important to follow the framing and finishing instructions to ensure proper placement of fireplace into the surrounding framing/finishing materials.

Wall sheathing materials 1/2 in. thick are specified in this installation manual to properly align with the factoryinstalled non combustible material.

WARNING! Risk of Fire! DO NOT remove the factoryinstalled non-combustible board or cover it with combustible material, such as:

Drywall (gypsum board)

Plywood

Materials that do not meet the ASTM E 136 Non-com-bustibility standard (below).

Removal of factory-installed,non-combustibleboard and/ or use of materials not meeting the ASTM E 136 standard may cause fire.

Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

Setting the Fireplace into the Framing

Unlike many traditional, single-sidedHeat & Glo fireplaces, this fireplace is recessed into surround framing. The left and right nailing tabs were designed for the SLR32 model as a means to ensure the fireplace is recessed to the correct location within the framing materials.

1.Bend two nailing tabs away from fireplace 180 degrees on both left and right nailing tabs. Do not adjust the column standoffs. See Figure 13.1.

2.Screw each nailing tab to the adjoining framing material. Ensure that the 1 inch air space clearance is maintained on the sides of the fireplace. See Figure 13.2.

FACTORY-INSTALLED

NON-COMBUSTIBLEBOARD

NAILING TABS

Figure 13.1 Nailing Tabs Installation Position

1/2 IN.

FRAMING

NAILING TAB

1/2 IN. FACTORY-SUPPLIED

NON-COMBUSTIBLEBOARD

Figure 13.2 Front Side Finishing Detail

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

49

WARNING! Risk of Fire! Maintain specified air space clearances to combustibles.

Failure to comply with these instructions may cause a fire or cause the appliance to overheat.

PILOT HOLES (7 LOCATIONS) TO ATTACH

NON-COMBUSTIBLEBOARD TO FRAMING

FACTORY-INSTALLED

NON-COMBUSTIBLEBOARD

=1 INCH MAX. SELF-TAPPINGSCREWS ALLOWED

= NO SCREWS ALLOWED

= 5-7INCHSELF-TAPPINGSCREWS

ALLOWED

Note: It is acceptable to use a silicone sealant with a minimum of 300ºF continuous exposure rating to adhere drywall to lower cover panel.

Figure 13.3 Finishing Details

CAUTION! Risk of Glass Damage and Cuts! DO NOT drill or install any type of screw or fastener into the lower cover panel. Sharp screw or fastener tips may penetrate and break the glass or cause cuts.

Note: Refer to Section 13.C regarding installation details associated with the Inside and Overlap Fit methods.

The SLR32 must be finished using either the Tonic or Martini decorative fronts. See Figures 13.12 and 13.13. The final fireplace installation can be accomplished by either the Overlap Fit or Inside Fit method. Reference Section 13.C regarding installation details associated with the Inside Fit and Overlap Fit methods.

It is acceptable to pre-drillholes and useself-tappedscrews in thefactory-installednon-combustibleboard to attachnon-combustiblebacker board for tile, marble, etc. Refer to Figure 13.3 for acceptable screw location and screw length requirements.

Self-tappingscrews up to one inch long can be installed through the nailing tab and outer1-3/4inch edges of thefactory-installednon-combustibleboard to secure the drywall adjacent to thefactory-installednon-combustibleboard. See Figure 13.3.

Do not drill or install screws which may penetrate the lower cover panel as this will restrict required access to the glass, battery-back-up,and remote receiver. See Figure 13.3.

The appliance is designed to accept 1/2 in. wall sheathing materials such as drywall, plywood, wood composites, or non-combustiblematerials. The type of material used depends whether the installation is an Inside or Overlap Fit Method. Refer to Section 13.C regarding installation details associated with the Inside an Overlap Fit methods.

The factory-suppliednon-combustibleboard must be used in all installations. It must be directly attached to structural framing adjacent to the appliance. Screw fasteners should be installed in the pilot holes provided in the outer perimeter of thenon-combustibleboard. See Figure 13.3.

The factory-suppliedboard is designed such that its edges will be at the approximate center of the adjacent framing, assuming it is1-1/2in. nominal thickness. This will allow the wallboard joints to occur on the center of the framing where the panels can be fastened properly. If the framing thickness is less than1-1/2in. nominal, such as with formed steel systems, then it may be necessary to adjust the adjacent framing dimensions so that the noncombustible board and wallboard joints are centered on the framing.

50

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

• For the initial Taping Coat, it is critical that a general-

 

purpose chemically hardening joint compound, such

 

as SHEETROCK™ Brand Durabond™ Setting-Type

 

Joint Compound, be used to fill the joint and embed

 

the mesh tape. Fiberglass-meshtape is recommended

 

because it will provide a more crack-resistantjoint

 

than one finished with paper tape. Let the Taping

 

Coat properly cure before applying subsequent Finish

 

Coats.

FIREPLACE OPENING

For the second and third finishing coats, it is acceptable

15-7/8IN. TO16-1/8IN.

to use a light-weightjoint compound and standard

 

 

application, curing and sanding methods.

 

Do not operate the fireplace during the drywall finishing

 

process. Allow the finish coat to cure for at least 24

 

hours prior to using the appliance.

 

 

 

 

 

 

 

 

 

 

 

 

Painting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If desired finishing includes a painted wall, 100%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

acrylic latex with compatible primer is recommend

 

 

 

 

 

 

 

 

 

 

 

 

around

the

appliance. Oil-basedor

standard

Figure 13.4. Required Fireplace Opening Height

acrylic

paints

may discolor due to heat

exposure.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: The lower cover panel must be pushed all the way

Wallboard Joint-CrackPrevention and Repair

down. The outer finishing flanges should line up. The fire-

Wallboard joints around the fireplace will be affected

place opening must be between 15-7/8in. and16-1/8in.

for the decorative fronts to fit correctly. See Figure 13.4.

by exposure to elevated temperatures, along with

 

 

 

 

 

 

 

 

 

 

 

 

other environmental and structural factors. The specific

 

 

 

 

 

 

 

 

 

 

 

 

methods presented in the previous section will help

Finish and Sealing Joints

prevent or minimize development of cracks.

 

All joints between the finished wall sheathing and the

If a crack does emerge adjacent the fireplace, it can be

appliance must be sealed with non-combustiblematerials.

permanently repaired by filling it with spackling paste or

Sealants, such as caulk or mastic used to seal the gap

paintable latex caulk, followed by repainting.

 

between the wall and the fireplace, should be rated at

 

 

 

 

a minimum continuous exposure to 300°F. Wall board

 

 

 

 

joints can be taped and sealed with combustible drywall

 

 

 

 

tape.

 

 

 

 

Finishing Around Opening with Gypsum Wallboard

Gypsum wallboard (drywall) joints adjacent to the fireplace opening require special attention to minimize potential development of cracking. Hearth and Home Technologies recommends the following steps to minimize potential cracks in the finished drywall around the fireplace opening:

When installing gypsum wallboard around the fireplace, install the hole for the fireplace opening in a single wallboard sheet, if possible. This will minimize the joints adjacent to the fireplace opening.

The factory-suppliednon-combustibleboard and the gypsum wallboard must join on the structural framing, where applicable. Wallboard andnon-combustibleboard should be fastened to the framing with at least1-1/4in. long screw fasteners, located within1-1/2in. from each corner, and at no more than 12 inch intervals along the joint length.

The wall-boardjoints should be finished with a Taping Coat, followed by at least two subsequent Finish Coats of joint compound.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

51

B. Mantel and Wall Projections

Combustible Mantel Legs Or Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear-

Extending Past The Face Of The Fireplace

 

 

ances to combustibles as specified. Framing closer than the

 

 

minimums listed must be constructed entirely of noncom-

 

 

bustible materials (i.e., steel studs, concrete board, etc.)

 

 

Failure to comply could cause fire.

 

 

Note: Fornon-combustiblefireplace finish material (marble,

 

 

stone, etc) specifications refer to Section 13.C.

 

 

Combustible Mantels

 

 

2 IN.

 

 

 

 

 

FIREPLACE

MINIMUM 3 FT. MAXIMUM

1/2 in.

 

OPENING

 

 

 

 

Thick Wall

12 in.

 

6 IN.

Sheathing

 

MINIMUM

 

MAX.

Figure 13.7 Combustible Mantel Leg or Wall Projections

 

 

 

 

 

(Acceptable on both sides of opening)

14 in. MEASUREMENT FROM TOP OF

MIN. FIREPLACE OPENING Non-combustibleMantel Legs Or Wall Projections Extending Past The Face Of The Fireplace

Figure 13.5 Clearances To Combustibles Mantels Or Other

 

 

 

 

Combustibles Above Appliance

 

 

 

 

Non-combustibleMantels

 

FIREPLACE

3 IN.

UNLIMITED

 

MINIMUM

 

 

 

OPENING

 

 

1/2 IN.

 

 

 

 

 

 

7 IN.

 

 

Thick Wall

12 IN.

 

 

 

 

Sheathing

 

 

 

 

MAX.

Figure 13.8 Non-CombustibleMantel Leg or Wall Projections

 

 

 

 

 

(Acceptable on both sides of opening)

 

 

14 IN.

 

 

 

 

 

MIN.

 

 

 

 

MEASUREMENT

 

 

 

 

 

FROM TOP OF

 

 

 

 

 

FIREPLACE

 

 

 

 

 

OPENING

1 IN.MIN.

 

 

 

 

 

 

 

 

 

4 IN.

 

 

 

 

 

MAX.

 

 

 

 

Figure 13.6 Clearances To Non-CombustibleMantels Or Other

 

 

 

 

Non-CombustiblesAbove Appliance

 

 

 

52

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

 

C. Facing Material

Facing and/or finishing materials must not interfere with air flow through louvers, operation of louvers or doors, or access for service.

Facing and/or finishing materials must never overhang into the glass opening.

Observe all clearances when applying combustible materials.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

WARNING! Risk of Fire! DO NOT install drywall or other combustible materials over the factory-installed non-com- bustible board. Overlapping materials could ignite.

Decorative facing material thickness is measured from the face of the factory-installednon-combustibleboard. See Figure 13.9 and Figure 13.10.

Overlap Requirement: See Figure 13.9.

Inside Fit requirement: See Figure 13.10 and Figure 13.11.

FACTORY-INSTALLED

NON-COMBUSTIBLE

BOARD

NON-COMBUSTIBLEFINISHING MATERIAL0-1IN. THICK

TONIC DECORATIVE

FRONT SHOWN

NON-COMBUSTIBLEFINISHING MATERIAL0-1IN. THICK

DRYWALL OR EQUIVALENT (1/2 IN.)

Figure 13.9 Overlap Fit Method (Tonic or Martini Decorative Front)

Non-CombustibleFinish Materials

0 - 1 inch thickness-OverlapFit Method

Both the Tonic and Martini decorative fronts are designed to overlap finish materials 0 inches to 1 inch thick. See Figure 13.9.

NOTICE: This one inch maximum not only includes the decorative finish materials (marble, tile, slate, etc) but also the mortar or adhesive used to attach the decorative finish material.

The non-combustiblefinish material can be installed up to the fireplace opening.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

53

Non-CombustibleFinish Materials

0 Inches to 4 Inches Thick-InsideFit Method

The Tonic decorative front is approved for inside fit applications. Non-combustiblefinishing materials up to 4 inches thick can be installed around the front (left, right, top, and bottom).

For the Tonic decorative front inside fit applications, the decorative front must be installed tight to the finishing flanges and must not overlap any finish material.

Ensure that minimum clearances to non-combustiblefinish materials meet the specifications in Figure 13.11.

FACTORY-INSTALLED

NON-COMBUSTIBLE

BOARD

0-4IN.

3/4 IN.

20-1/2IN. APPLIANCE

OPENING (HEIGHT)

3 IN.

0- 4 IN.

DRYWALL OR

EQUIVALENT

(1/2 IN.)

Figure 13.10 Inside Fit Method (Tonic Decorative Front Only)

Non-CombustibleFinish Material0-4Inches Thick

3/4 IN.

3/4 IN.

 

3 IN.

 

Bottom Joint

Figure 13.11 Noncombustible Surface Finishing Material 0-4Inch

Thick-InsideFit Method (Tonic Decorative Front

Only)

54

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

D. Decorative Fronts

WARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place.

Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used.

Inside and Overlap Fit

See Section 13.C.

TONIC DECORATIVE FRONT

(TN-SLR32-**)

Figure 13.12 Tonic Decorative Front

Overlap Fit Only

See Section 13.C.

MARTINI DECORATIVE FRONT

(MT-SLR32-**)

Figure 13.13 Martini Decorative Front

The tinted glass on the Martini Decorative Front meets the tempered glass specifications in Section 1.B of this installation manual.

E

F

 

A

 

B

 

C

 

D

 

Figure 13.14 Dimensions of Tonic Decorative Front.

Table 1. Dimensions of Tonic Decorative Front.

A

Top of decorative front to bottom of

26-1/2in.

670 mm

appliance.

 

 

 

B

Bottom of decorative front to bottom of

8-3/4in.

175 mm

appliance.

 

 

 

C

Inside dimension of decorative front

27 in.

991 mm

(width).

 

 

 

D

Outside dimension of decorative front

32-1/2in.

1130 mm

(width).

 

 

 

E

Inside dimension decorative front

11-1/2in.

327 mm

(height).

 

 

 

F

Outside dimension of decorative front

17-3/4in.

495 mm

(height).

 

 

 

D

A

B

C

Figure 13.15. Dimensions of Martini Decorative Front

Table 1. Dimensions of Martini Decorative Front.

A

Top of decorative front to bottom of

27-3/16IN.

691 mm

appliance.

 

 

 

B

Bottom of decorative front to bottom

8-3/8IN.

212 mm

of appliance.

 

 

 

C

Outside dimension of decorative

34-3/16IN.

868 mm

front (width).

 

 

 

D

Outside dimension of decorative

18-7/8IN.

480 mm

front (height).

 

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

55

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14.F.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox. The standard glass rock media and manual bag assembly are also shipped underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Glass Rock Media Kit

NOTE: During appliance set up, gas pressure verification, or troubleshooting, do not operate appliance with glass off for more than 30 seconds to prevent the media tray form warping. Flames may curl back underneath the

media tray wtih glass removed.

WARNING! Choking Hazard! Keep glass rock media out of reach of children.

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Cleaning the Glass Rock Media

During shipment of the glass rock media, dust and debris can accumulate in the rock bag. It is recommended that the glass rock media be rinsed thoroughly with water to remove dust and small glass rock particles. An easy method to clean the glass rock media is to empty the contents of the bag into a bucket and rinse thoroughly with a garden hose. Allow the glass rock media to dry before installing into the fireplace.

Installation

1.Figure 14.2 shows the outline of the media tray edges and the gap between the edges of the media tray and the firebox. DO NOT install glass rock media inside the dashed lines. This may cause delayed ignition, undesirable burner flame, or lighting issues.

NOTICE: Care should be taken to avoid placing glass rock media between the left, right and back edges of the media tray and the firebox. Blocking this gap may cause an undesirable flame appearance. See Figure 14.2.

WARNING

Delayed Ignition Risk

Place glass rock media according to instructions.

Do NOT place glass rock media in area in front of pilot or between burner tracks.

Do NOT place glass rock media in a position that they may fall into area in front of pilot.

Do NOT use any media other than the glass rock media supplied with this fireplace.

Do NOT use more than one 10 lb. bag of glass rock media per fireplace.

Fireplace will not function properly.

Delayed ignition may occur.

NO GLASS ROCK

MEDIA INSIDE

DASHED LINE.

Figure 14.1. Glass Rock Media Jig Location

2.Place an even layer of glass rock media around the base pan as shown in Figure 14.2. Do not place glass rock media between the inside edges of the media tray. Place entire contents of the bag onto the media tray. See Figure 14.2.

3.Remove rock placement jig by removing one screw that attaches jig to pilot shield. Location of the jig is represented by the white, boxed area in Figure 14.1. Place smaller sized glass rock media on top of the pilot shield. See Figure 14.3. Do not place glass rock media in front of pilot assembly.

NO GLASS ROCK

GAP

MEDIA INSIDE

 

DASHED LINES.

 

Figure 14.2. Maintain Media Tray Air Spaces.

56

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

PILOT SHIELD

Figure 14.3. Placing Glass Rock Media on Pilot Shield

WARNING! Risk of Fire! DO NOT place glass rock media directly in front of the pilot assembly or between the burner tracks over the burner ports.

4. Install only approved media kit. Options include:

MEDIA-AMBER

MEDIA-BLACK

MEDIA-CLEAR

MEDIA-COBALT

MEDIA-BK2-GEMS

MEDIA-WH2-GEMS

MEDIA-STONES-2

SLR32-LOGS

MEDIA-CL2-GEMS

GLASS32-LINER

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

57

F. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace as a complete assembly.

Removing Fixed Glass Assembly

1.Remove the decorative front.

2.Locate the two spring latches that are on the upper left and right of the fireplace.

3.Use both index fingers to release spring latches. See Figure 14.4.

4.Allow glass to tilt forward. Grasp glass on the upper right and left sides and lift glass “up” and “out.”

Replacing Fixed Glass Assembly

1.Locate glide tabs on lower left and right corners.

2.Grasp glass on upper right and left sides and tilt bottom of glass assembly toward fireplace.

3.Allow of the bottom gasketing of the glass assembly to touch the face of the fireplace.

4.Put pressure on the glass as you allow the glass assembly to drop into the two lower glass clips. See Figure 14.4.

5.Tilt top of glass towards fireplace and engage both top spring latches

G. Install the Mesh

The mesh front is included with the Tonic front. The Martini tinted glass front does not include mesh.

1.Remove fixed glass assembly as instructed.

2.Place glass assembly into mesh screen such that the four mesh clips attached to the mesh assembly snap into the four corresponding slots on the fixed glass assembly.

H. Air Shutter Setting

Air shutter settings may be adjusted by a qualified installer at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.5.

Loosen the 1/4 in. screw.

Twist shutter to adjust

Shutter may be open for longer horizontal vent runs.

Do not close the air shutter more than 1/8 in. for NG or 1/4 in. for LP when glass rock media (shipped with appliance) is installed. See Table 14.1 below for settings when optional media (fiber) stones kit or optional log kit are installed. See instructions provided with kit.

Tighten the screw.

NOTICE: If the flames appear to be orange, open the air shutter to prevent residue buildup on the glass.

UPPER SPRING LATCH

Figure 14.5 Air Shutter

 

 

LOWER GLASS CLIP

 

 

 

 

 

 

Air Shutter Settings

 

 

 

SLR32

NG

LP

 

Glass Rock Media

1/8 in.

1/4 in.

 

Media Stones (Optional Kit)

 

 

 

 

Logs (Optional Kit)

3/16 in.

5/16 in.

 

Table 14.1

 

 

Figure 14.4 Fixed Glass Assembly

58

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

15 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician.

A. IntelliFire Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor

The ignitor/module

 

are connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

b. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

spark.

 

shorts in the wiring.

ule to pilot assembly. Verify connections underneath pilot assembly

 

 

are tight; also verify connections are not grounding out to metal

 

 

chassis, pilot burner, pilot enclosure, mesh screen if present, or

 

 

any other metal object.

 

 

 

 

c. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

d. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5

 

 

mm) away from “I” terminal on module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal

 

 

module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked

 

 

insulator around electrode. Replace pilot if necessary.

 

 

 

2. Pilot won’t light,

a. No power or transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly.

voltage of transformer under load at spade connection on module

spark.

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

b. A shorted or loose connection in wir-

Remove and reinstall the wiring harness that plugs into module.

 

ing configuration or wiring harness.

Verify there is a tight fit. Verify pilot assembly wiring to module. Re-

 

 

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

c. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

d. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

e. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Re-

 

 

move ignitor wire “I” from module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal

 

 

module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked

 

 

insulator around electrode.

 

 

 

3. Pilot sparks, but

a. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits, inlet pressure must not

 

 

exceed 14 in. W.C.

 

 

 

 

b. Ignitor gap is incorrect.

Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm).

 

 

 

 

c. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

d. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

 

solenoid ohms readings.

age is below 2.7.

 

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

59

IntelliFire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

a. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify

ues to spark, and main

 

connections are not grounding out to metal chassis, pilot

burner will not ignite.

 

burner, pilot enclosure or screen if present, or any other

(If the pilot continues

 

metal object.

to spark after the

 

 

b. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. Verify cor-

not occurred.)

 

 

rect pilot orifice is installed and gas inlet is set to pressure

 

 

 

 

specifications. Polish flame sensing rod with fine steel wool

 

 

to remove any contaminants that may have accumulated

 

 

on flame sensing rod.

 

 

 

 

c. Module is not grounded.

Verify module is securely grounded to metal chassis of

 

 

appliance. Verify that wire harness is firmly connected to

 

 

the module.

 

 

 

 

d. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing rod

 

nated flame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

flame sensing rod to white sensor wire. Polish flame sens-

 

 

ing rod with fine steel wool to remove any contaminants

 

 

that may have accumulated on flame sensing rod. Verify

 

 

continuity with a multimeter with ohms set at lowest range.

 

 

Replace pilot if any damage is detected.

 

 

 

 

e. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

switch or wall switch in ON position. If there is no spark at

 

 

“I” terminal module must be replaced. If there is a spark at

 

 

“I” terminal, module is fine.

 

 

 

60

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

MK

L

N

J

I Ø

A

B

H

O

 

R

 

 

E

 

 

Q

 

 

S

 

P

F

 

C

 

 

G

 

 

D

Location

Inches

Millimeters

A

39

991

B

27-1/4

692

C

31

787

D

36-3/4

933

E

16

406

F

3-1/2

89

G

8-1/4

210

H

39-3/4

1010

I

6-5/8

168

Location

Inches

Millimeters

J

18-5/16

465

K

1

25

L

12-7/8

327

M

25-3/4

654

N

7-1/4

184

O

36

914

P

7-1/2

191

Q

2-1/4

57

R

37

940

S

9-3/4

248

Figure 16.1 Appliance Dimensions

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

61

B. Vent Components Diagrams

 

13-7/8in.

9-1/2in.

 

 

 

 

(352 mm)

(241 mm)

11-5/8in.

 

 

 

 

 

 

 

 

 

 

(295 mm)

 

 

14 in.

 

 

7-1/8in.

12-1/8in.

 

(356 mm)

 

 

(308 mm)

 

 

 

(181 mm)

 

 

 

 

 

 

 

DRC-RADIUS

5-3/4in.

 

 

 

Cap Shield

(146 mm)

COOL-ADD

 

 

 

 

 

 

 

 

 

 

Cap Shield

 

 

9 in.

12-1/2in.

11-7/8in.

5 in.

2-3/4in.

(229 mm)

(302 mm)

(127 mm)

 

 

(317 mm)

(70 mm)

 

 

 

 

 

 

 

 

 

 

 

11-1/2in.

13-7/8in.

 

 

 

 

(280 mm)

 

 

 

 

 

(352 mm)

 

 

 

12-1/4in.

 

 

 

 

 

(311 mm)

 

 

 

 

16 in.

 

 

 

 

 

(406 mm)

PVK-80

 

 

 

 

 

 

DVP-BEK2

 

 

(For use with IPI and DSI appliances only.)

DVP-HPCCap Brick Extension

Figure 16.2 Vent Components

 

 

 

62

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

 

B. Vent Components Diagrams (continued)

 

 

 

 

6-1/2in.

6-1/2in.

 

 

 

165 mm

 

 

 

 

165 mm

 

 

 

6-1/2in.

 

 

 

 

8-3/4in.

 

 

 

165 mm

 

 

 

9-1/4in.

222 mm

 

 

6 in.

 

 

235 mm

 

 

152 mm

 

6-5/8in.

 

 

 

 

168 mm

 

 

 

6-5/8in.

SLP-45- 45° Elbow

 

 

 

 

 

 

168 mm

 

 

 

 

 

 

 

 

9-7/8in.

 

 

 

 

251 mm

 

 

 

SLP9090° Elbow

 

Effective Height/Length

 

 

Pipe

inches

mm

 

Effective

SLP4

4

102

 

SLP6

6

152

 

Height/

 

Length

SLP12

12

305

 

 

SLP24

24

610

EFFECTIVE HEIGHT/

 

SLP36

36

914

LENGTH

 

 

 

SLP48

48

1219

SLP-FLEX-PIPE

SLP-PIPE

SLP6A

2 - 6

51 - 152

 

SLP12A

2 - 12

51 - 305

 

 

 

 

SLP-FLEX-2

24

610

 

 

SLP-FLEX-3

36

914

26 in.

 

SLP-FLEX-5

60

1524

 

660 mm

 

SLP-FLEX-10

120

3048

 

DVP-HSM-B

Extended Heat Shield

SLP-HVS

SLP-FS

SLP-WS

Horizontal Pipe

Ceiling Firestop

Wall Shield Firestop

Support

 

 

Figure 16.5 SLP Series Vent Components

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

63

B. Vent Components Diagrams (continued)

 

SLK-SNKD

 

SLP-CCS-BK

SLP-TVHW

 

 

Cathedral Ceiling

Vertical

 

Snorkel

 

 

 

Support Box-Black

Termination Cap

Termination Cap

 

 

SLP-DCF-BK

 

SLP-WT-BK

SL-2DVP

Ceiling Firestop

 

Wall Thimble-Black

Adapter

Black

 

 

 

 

 

 

 

 

12 IN.

 

 

 

 

305 mm

 

 

 

7 IN.

 

 

 

 

178 mm

 

 

 

15-1/2IN.

 

 

 

394 mm

 

SLP90

SL-2DVP

 

DVP-FBHT

DVP-FBHT

Figure 16.6 SLP Series Vent Components

 

 

64

 

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm). The heat shield is designed to be used on a wall 4 in. to7-1/4in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than7-1/4in. (184 mm) aDVP-HSM-Bwill be required.

 

8 in.

 

 

 

 

(203 mm)

 

 

 

 

Heat

 

 

 

 

Shield

 

 

 

15-1/8in.

 

 

 

 

(384 mm)

 

 

 

 

 

 

Term Cap

Minimum

Maximum

 

 

Effective Length

Effective Length

 

Max

 

12 in.

Trap1

3-1/8in.

4-3/4in.

Effective

79 mm

121 mm

(305 mm)

Length

 

 

5-1/4in.

9-1/4in.

 

SLP-TRAP

Trap2

 

133 mm

235 mm

 

Horizontal Termination Cap

 

 

 

 

 

15 in.

(381 mm)

8-1/8in.

13 in.

Effective Length

 

 

(206 mm)

(330 mm)

5-1/2in.

8-3/8in.

5-3/4to8-3/8in.

 

 

 

 

146 to 213 mm

140 mm

213 mm

 

 

 

87°

 

 

 

 

10-1/2in.

267 mm

10-7/8in. 276 mm

SLP-HRC-SS

SLP-HRC-ZC-SS

HORIZONTAL TERMINATION CAP

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

65

B. Vent Components Diagrams (continued)

13-5/8IN.

346 mm

12-1/2IN.

318 mm

20-3/4IN.

527 mm

PVI-SLP

Power Vent Inline

Note: The PVI-SLPcan only be used with Natural Gas Appliances.

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 ft. PV Wire Harness

PVI-WH10

20 ft. PV Wire Harness

PVI-WH20

40 ft. PV Wire Harness

PVI-WH40

60 ft. PV Wire Harness

PVI-WH60

80 ft. PV Wire Harness

PVI-WH80

100 ft. PV Wire Harness

PVI-WH100

Note: Wire harnesses required to power thePVI-SLPconnect to the appliance and are ordered separately fromPVI-SLP.Contact your dealer to order.

12-1/2IN.

(318 mm)

 

16 IN.

 

406 mm

 

4-1/2IN.

 

114 mm

 

9-3/16IN.

 

(233 mm)

13-5/8

16-11/16IN.

(346 mm)

424 mm

SLP-LPC

SLP Low Profile Cap

15 IN.

(381 mm)

16-11/16IN.

(424 mm)

COAXIAL to COLINEAR VENTING

LINK-DV30B

DVP-2SL

DV-46DVA-GCL

Flex Liner Kit

Adapter

Coaxial/Colinear Appliance Connector

Figure 16.10 Coaxial to Colinear Vent Components

 

66

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

C. Service Parts

SLR32

 

 

Landscape DV Appliance

Beginning Manufacturing Date: Oct 2011

 

Ending Manufacturing Date: ______

 

 

2

1

 

 

 

 

4

3

 

 

5

 

 

 

6

 

 

8

7

 

 

 

 

 

9

 

 

 

 

 

11

12

 

 

 

 

 

10

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

 

parts for your appliance please provide model number and serial number. All parts listed

 

 

in this manual may be ordered from an authorized dealer.

 

 

at depot

 

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

1

Elbow Heat Shield

 

2269-168

 

 

2

Sheet Rock Ledge

 

2269-114

 

3

Top Panel, Finishing Edge

 

2269-102

 

 

4

Non Combustible Board, Top

 

2269-403

 

 

5

Media Tray

 

2269-118

 

 

6

Base Pan

 

2269-117

 

 

7

Burner NG

 

2269-007

Y

 

8

Glass Door Assembly

 

SRV-GLA32

Y

 

9

Lower Cover Panel

 

2269-103

 

 

10

Valve Assembly

 

Refer to valve page

 

 

11

Junction Box Bracket

 

2269-154

 

 

12

Junction Box

 

4021-013

Y

Additional service part numbers appear on following page.

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

67

 

C. Service Parts

 

 

 

SLR32

 

 

 

 

Beginning Manufacturing Date: Oct 2011

 

 

 

 

Ending Manufacturing Date: ______

#11 Valve Assembly

11.3

 

 

 

 

 

 

11.4

 

 

 

 

 

 

 

11.2

 

 

 

 

 

 

11.1

 

 

 

 

 

11.5

 

 

 

 

 

 

11.6

 

 

 

 

 

 

11.7

 

 

 

 

 

 

11.8

11.16

 

 

 

 

 

11.9

11.15

11.14

 

 

 

 

11.10

 

11.13

 

 

 

 

 

 

 

 

 

 

 

 

11.12

 

 

 

 

 

 

11.11

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

10.1

3-HoleGrommet

 

 

 

2118-420

 

10.2

Pilot Bracket

 

 

 

2269-127

 

10.3

Pilot Shield

 

 

 

2269-123

 

10.4

Pilot Assembly NG

 

 

 

2208-012

Y

Pilot Assembly LP

 

 

 

2208-013

Y

 

 

 

 

10.5

Orifice NG (#45C)

 

 

 

582-845

Y

Orifice LP (.125mm C)

 

 

 

582-8125

Y

 

 

 

 

10.6

Bulkhead W/Flex Tube

 

 

 

383-302A

Y

10.7

Valve Bracket

 

 

 

2269-153

 

10.8

Valve NG

 

 

 

593-500

Y

Valve LP

 

 

 

593-501

Y

 

 

 

 

10.9

Male Connector

 

Pkg of 5

303-315/5

Y

10.10

Thermostat Wire Assembly

 

 

2118-170

Y

10.11

Flex Ball Valve Assembly

 

 

 

531-320A

Y

10.12

Jumper Wires 21 in

 

 

 

2012-206

Y

10.13

3 Volt Transformer

 

 

 

593-593A

Y

10.14

Battery Pack

 

 

 

593-594A

Y

10.15

Module Wire Assembly

 

 

 

593-590A

Y

10.16

Module

 

 

 

593-592

Y

Additional service part numbers appear on following page.

 

 

 

 

68

 

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

 

 

C. Service Parts

SLR32

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Exhaust Restrictor

 

530-299

 

 

Gasket Assembly

 

 

 

 

Contains burner neck, shutter bracket, vent, seal cap,

 

2113-080

 

 

valve plate, and air passage gaskets

 

 

 

 

 

 

 

 

 

Glass Latch Assembly , Top

Pkg of 2

33858/2

Y

 

Glass Latch Assembly , Bottom

 

2143-119

 

 

Heat Shield, Inner

 

2269-109

 

 

Touch Up Paint

 

TUP-GBK-12

 

 

Wall Switch Kit

 

WSK-21-W

 

 

Conversion Kit NG

N/A

 

 

Conversion Kit LP

LPK-SLR32

Y

 

Pilot Orifice NG

593-528

Y

 

Pilot Orifice LP

593-527

Y

 

Regulator NG

NGK-DXF

Y

 

Regulator LP

LPK-DXF

Y

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12

69

D. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

2000-945

Printed in U.S.A. - Copyright 2012

70

Heat & Glo • SLR32 • 2269-900Rev. E • 4/12