Heat & Glo LifeStyle SLR (COSMO) User Manual

Size:
3.43 Mb
Download

Owner’s Manual

Installation and Operation

Model:

SLR (Cosmo)

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch.DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

1

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas fireplace, an elegant and clean alternative to wood burning fireplaces. The Heat & Glo gas fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas fireplace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fireplace products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your fireplace.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on fireplace: _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 20802 Kensington Boulevard, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas (Sorte De Gaz): This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1

in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglementsNATURAL GAS locaux ou, en l’absence de tels reglements, selon les codes d’installationCAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

Approved Minimum (De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

Maximum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

Minimum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

IN CANADA

 

Model:

XXXXXXXX

ALTITUDE:

0-0000FT.

0000-0000FT.

(Modele):

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

(Serie):

Model Number

Serial Number

2

Heat & Glo • SLR • 2143-900Rev. B • 7/08

Safety Alert Key:

DANGER! Indicates a hazardous situation which, if not avoidedwill result in death or serious injury.

WARNING! Indicates a hazardous situation which, if not avoidedcould result in death or serious injury.

CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 6 C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 6 E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 6 F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 6 G. Requirements for the Commonwealth of Massachusetts. . 7

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . . 9 E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 F. Remote Controls, Wall Controls and Wall Switches. . . . . . 9 G. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . 9 H. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 10 I. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 J. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 11

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .12

B. Maintenance Tasks-QualifiedService Technician . . . . . . 13

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 14

B. Design and Installation Considerations . . . . . . . . . . . . . . 15

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 15

D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 15

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 16

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 17

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 18

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 20

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 31 B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 31 C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 32 D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 33

9 Appliance Preparation

A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

B. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 35

10 Installing Vent Pipe (SLP Pipe)

A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 36 B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 37 C. Secure The Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . 37 D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 38 E. Install Decorative Ceiling Components . . . . . . . . . . . . . . 38 F. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 39 G. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 39 H. Install RF4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 I. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 41 J. Install Decorative Wall Components . . . . . . . . . . . . . . . . 41 K. Heat Shield Requirements for Horizontal Termination . . . 41 L. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 42

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 44

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

B. Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 45

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 45

D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 46

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 46

Heat & Glo • SLR • 2143-900Rev. B • 7/08

3

13 Finishing

A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 47

B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 50

C. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

D. Decorative Fronts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 54

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 54

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

E. Rock Media Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 55

F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

G. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

H. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

15 Troubleshooting

A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 58

16 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 60

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 61

C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Î = Contains updated information.

4

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Limited Lifetime Warranty

LIMITED LIFETIME WARRANTY HEAT & GLO GAS APPLIANCE PRODUCTS

BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEAT & GLO will replace or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.

EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in material or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and limitations described below.

CONDITIONS, EXCLUSIONS AND LIMITATIONS:

1.This warranty applies to the original owner only and is nontransferable.

2.This warranty applies only to Products installed in the United States of America or Canada.

3.This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an expedient and cost-effectivemanner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT.

4.Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-YearWarranty.

5.Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty unless expressly authorized and approved by HEAT & GLO in writing.

6.Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.

7.This warranty will be void if:

a)The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.

b)Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved by HEAT & GLO in writing.

c)Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.

d)The Product is damaged due to shipping, improper handling, accident, abuse or misuse.

e)Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.

f ) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HEAT & GLO dealer or supplier.

NOTES TO CUSTOMER:

1.In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual servicing by an authorized HEAT & GLO dealer.

2.Please complete this information and retain this warranty in a safe place for future reference: Installation Date:___

Model #:_________________ Serial #:______________ Installing Contractor:_________________________

3.HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products.

© 2007 Hearth & Home Technologies Inc.

060-981E10/07

Heat & Glo • SLR • 2143-900Rev. B • 7/08

5

1 Listing and Code Approvals

A. Appliance Certification

MODEL: SLR

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Vented Gas Fireplace Heater

STANDARD: ANSIZ21.88a-2007CSA2.33a-2007

Vented Gas Fireplace Heaters

This product is listed to ANSI standards for “Vented Gas Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Tempered Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

C. BTU Specifications

Models

 

Maximum

Minimum

Orifice

 

Input

Size

(U.S. or Canada)

Input BTU/h

BTU/h

(DMS)

 

 

 

 

 

 

 

 

US

26,000

N/A

#42

 

 

(0-2000FT)

SLR (NG)

 

 

 

 

 

CANADA

21,870

N/A

#43

 

 

(2000-4500

 

 

FT)

 

 

 

 

 

US

25,000

N/A

.057

 

 

(0-2000FT)

SLR (LP)

 

 

 

 

 

CANADA

23,500

N/A

#54

 

 

(2000-4500

 

 

FT)

 

 

 

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper orifice size.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

Heat & Glo Quality Systems registered by SGS ICS

6

 

 

Heat & Glo • SLR • 2143-900Rev. B • 7/08

 

 

 

 

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

G.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) in. in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

7

2 Operating InstructionsUser Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

If you expect that small children or vulnerable adults may come into contact with this fireplace, the following precautions are recommended:

Install a physical barrier such as:

-A decorative firescreen.

-Adjustable safety gate.

Keep remote controls out of reach of children.

Never leave children alone near a hot fireplace, whether operating or cooling down.

Teach children to NEVER touch the fireplace.

Consider not using the fireplace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/staysafe.

To prevent unintended operation when not using your fireplace for an extended period of time (summer months, vacations, trips, etc):

Remove batteries from remote controls.

Turn off wall controls.

Unplug 3 volt adapter plug and remove batteries on IPI models.

B. Your Fireplace

WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire or injury.

Install a switch lock or a wall/remote control with child protection lockout feature.

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.D.

FIXED GLASS ASSEMBLY

(NOT SHOWN)

SECTION 14.K.

CLEAR SPACE

SECTION 2.C.

Figure 2.1 General Operating Parts

8

Heat & Glo • SLR • 2143-900Rev. B • 7/08

C. Clear Space

WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2.

Avoid placing candles and other heat-sensitiveobjects on mantel or hearth. Heat may damage these objects.

 

3

 

 

 

 

CLEAR

 

 

OF

FT.

SPACE

 

IN

 

 

FRONT

 

 

FIREPLACE

Figure 2.2

Clear Space

 

 

D. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

ÎThis decorative front has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

E. Fixed Glass Assembly

See Section 14.F.

F.Remote Controls, Wall Controls and Wall Switches

Follow the instructions supplied with the control installed to operate your fireplace:

For safety:

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

See your dealer if you have questions.

G. Before Lighting Fireplace

Before operating this fireplace for the first time, have a qualified service technician:

Verify all shipping materials have been removed from inside and/or underneath the firebox.

Review proper placement of logs, ember material and/or other decorative materials.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

9

H. Lighting Instructions (IPI)

The IPI system may be operated with two D-cellbatteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS (IPI)

1.Turn off all electric power to the appliance.

2.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

4.Turn on all electric power to the appliance.

5.To light the burner, flip the ON/OFF switch to the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6.If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Turn wall control or ON/OFF switch to “OFF”.

2.Turn off all electric power to the appliance if service is to be performed.

593-913F

Final inspection by

10

Heat & Glo • SLR • 2143-900Rev. B • 7/08

I. After Fireplace is Lit

Initial Break-inProcedure

The fireplace should be run three to four hours continuously on high.

Turn the fireplace off and allow it to completely cool.

Ε Remove fixed glass assembly. See Section 14.F.

Clean fixed glass assembly. See Section 3.

Replace the fixed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the fireplace.

NOTICE! Open windows for air circulation during fireplace break-in.

Some people may be sensitive to smoke and odors.

Smoke detectors may activate.

J.Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the fireplace warms, this conden-

sation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the fireplace is allowed to

burn for 20 to 40 minutes.

 

 

 

 

When first operated, this fireplace may release an odor for the first several hours. This is caused

Odor from fireplace

by the curing of materials from manufacturing. Odor may also be released from finishing materials

and adhesives used near the fireplace. These circumstances may require additional curing related

 

 

to the installation environment.

 

 

Film on the glass

This is a normal result of the curing process of the paint and logs. Glass should be cleaned within

3 to 4 hours of initial burning. A non-abrasivecleaner such as gas appliance glass cleaner may be

 

 

necessary. See your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the

Metallic noise

sound produced by a furnace or heating duct. This noise does not affect the operation or longevity

 

of the fireplace.

 

 

 

There may be some “cracking” noise coming from the fireplace during the first few heating and

Rock noise

cooling cycles. This noise is associated with settling rock and some minor cracking of larger

pieces of rock. This will lessen over time as the glass rock is conditioned to the heating and cool-

 

 

ing temperature changes.

 

 

Rocks falling through basepan

It is expected that a few small pieces (approximately 10 pieces) of rock may fall through the base-

pan and come to rest on the fireplace bottom. This has no affect on fireplace performance.

 

 

 

Heat & Glo • SLR • 2143-900Rev. B • 7/08

11

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-freeservice. We recommend annual service by a qualified service technician.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care.

Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

DO NOT clean glass while it is hot

Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.

Remove door or decorative front from fireplace and set aside on work surface.

Ε See Section 14.F for instructions to remove fixed glass assembly.

Clean glass with a non-abrasivecommercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

Ε Refer to Section 14F for glass removal and replacement instructions.

Reinstall door or decorative front.

Inspect for scratches, dents or other damage and repair as necessary.

Check that louvers are not blocked.

Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote control instructions.

Locate remote control transmitter and receiver.

Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

Place batteries as needed in remote transmitters and battery-poweredreceivers.

Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

Remove batteries from remote controls.

Unplug 3 volt adapter plug on IPI models.

12

Heat & Glo • SLR • 2143-900Rev. B • 7/08

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

Inspect for corrosion or separation.

Verify weather stripping, sealing and flashing remains intact.

Inspect draft shield to verify it is not damaged or missing.

B.Maintenance Tasks-QualifiedService Technician

The following tasks must be performed by a qualified service technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, drop cloth and a stable work surface.

Inspect gasket seal and its condition.

Inspect fixed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

Confirm there is no damage to glass or glass frame. Replace as necessary.

Verify that fixed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Firebox

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, sandpaper, steel wool, cloths, mineral spirits, primer andtouch-uppaint.

Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

Replace fireplace if firebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, dust cloths

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that

have penetrated the sheet metal are sharp and should be avoided.

Remove all foreign objects.

Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer.

Verify burner is properly secured and aligned with pilot

 

 

or igniter.

 

• Clean off burner top, inspect for plugged ports, corrosion

 

 

or deterioration. Replace burner if necessary.

 

Verify batteries have been removed from battery back-

 

 

up IPI systems to prevent premature battery failure or

 

 

leaking.

 

Check for smooth lighting and ignition carryover to all

 

 

ports. Verify that there is no ignition delay.

 

Inspect for lifting or other flame problems.

 

• Verify air shutter setting is correct. See Section 14.H for

Î

 

 

required air shutter setting. Verify air shutter is clear of

 

 

dust and debris.

 

Inspect orifice for soot, dirt and corrosion. Verify orifice

 

 

size is correct. See Service Parts List for proper orifice

 

 

sizing.

 

Verify manifold and inlet pressures. Adjust regulator as

 

 

required.

 

Inspect pilot flame pattern and strength. See Figure 3.1

 

 

for proper pilot flame pattern. Clean or replace orifice

 

 

spud as necessary.

 

• Inspect IPI flame sensing rod for soot, corrosion and

 

 

deterioration. Clean with emery cloth or replace as

 

 

required.

 

Verify IPI millivolt output. Replace as necessary.

 

Verify that there is not a short in flame sense circuit by

 

 

checking continuity between pilot hood and flame sense

 

 

rod. Replace pilot as necessary.

 

 

 

 

 

 

 

Figure 3.1 IPI Pilot Flame Pattern

Heat & Glo • SLR • 2143-900Rev. B • 7/08

13

4

Getting Started

Installer Guide

 

 

 

A. Typical Appliance System

NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

VERTICAL TERMINATION CAP (SECTION 10)

NON-COMBUSTIBLEROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE

(SECTION 10)

VENT PIPE (SECTIONS 7&8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.C)

FRAMING/HEADER (SECTION 5)

HORIZONTAL TERMINATION CAP

(SECTION 7)

WALL PENETRATIONFRAMING

(SECTION 8B)

STORM COLLAR (SECTION 10)

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY FROM VENT PIPE IF ATTIC IS INSULATED. (SECTION 8.D)

FRAMING HEADED

OFF IN CEILING

JOISTS (SECTION 8.C)

WALL SWITCH

GAS LINE (SECTION 11)

Figure 4.1 Typical System

14

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring requirements.

Framing and finishing details.

Whether optional accessories—devicessuch as a wall switch or remotecontrol—aredesired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

High temperature caulking material

Hammer

Phillips screwdriver (magnetic)

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in. magnetic)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Flat blade screwdriver

Non-corrosiveleak check solution

1/2 - 3/4 in. length, #6 or #8 Self-drillingscrews One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

If packaged separately, the log set and appliance grate must be installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

15

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

It is important to follow the framing and finishing instructions step by step to ensure proper placement of fireplace in the surrounding framing/finishing materials.

Unlike many traditional, single sided Heat & Glo fireplaces, the SLR is recessed into surround framing. The left and right nailing tabs were designed to ensure the fireplace is recessed to the correct location within the framing materials. Refer to Section 13 for detailed instructions on finishing.

A

E

1 IN.

D*

 

A

ALCOVE

B

INSTALLATION

C

TOP VENT

 

ONE 900 ELBOW

TOP VENT

ONE 90° ELBOW

B

F

 

A

B

C

D

E

F

Inches

53-1/32

48

75

See Section D.

19-9/32

17-3/4

Millimeters

1347

1218

1905

Figure 5.5 & 5.6

490

451

 

 

 

 

 

 

 

Î Figure 5.1 Appliance Locations

16

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Constructing the Appliance Chase

A chase is a vertical box-likestructure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase.

NOTICE: Treatment of ceiling firestops and wall shield firestops and construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth.DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specified air space clearances to appliance and vent pipe:

Insulation and other materials must be secured to prevent accidental contact.

The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fireplace or chimney.

Failure to maintain airspace may cause overheating and a fire.

Note: Figure 5.2 shows the fireplace installed on the floor. However, this fireplace can be elevated off the floor provided that the fireplace is properly supported by framing materials and the ceiling clearances are maintained.

 

MEASURE FROM TOP OF

A

FIREPLACE OPENING

 

E

F

B

 

H

C

J

G

D

 

 

I

MINIMUM FRAMING DIMENSIONS*

 

A

B

C

D

E

F

G

H

I

J

 

Rough

Rough

Rough

Rough

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

Opening

Opening

Opening

Opening

 

to Ceiling

Floor

Flooring

Appliance

Appliance

Appliance

 

(Vent Pipe)

(Height)

(Depth)

(Width)

 

 

 

 

 

 

 

Inches

8-5/8

42 1/4

18-1/4

50

31

0

0

1

1

36

 

 

 

 

 

 

 

 

 

 

 

Millimeters

219

1073

464

1270

787

0

0

25

25

914

 

 

 

 

 

 

 

 

 

 

 

Figure 5.2. Clearances to Combustibles

Heat & Glo • SLR • 2143-900Rev. B • 7/08

17

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantels

1/2 in.

Thick Wall

Sheathing 12 in. MAX.

14 in. MEASUREMENT FROM TOP OF MIN. FIREPLACE OPENING

Figure 5.3 Clearances To Combustible Mantels Or Other Combustibles Above Appliance

Non-combustibleMantels

1/2 in.

Thick Wall

Sheathing 12 in. MAX.

14 in. MEASUREMENT MIN. FROM TOP OF FIREPLACE

OPENING

Figure 5.4 Clearances To Non-CombustibleMantels Or OtherNon-CombustiblesAbove Appliance

Note: Fornon-combustiblefireplace finish material (marble, stone, etc) specifications refer to Figure 13.13 and Figure 13.15.

18

Heat & Glo • SLR •

Combustible Mantel Legs Or Wall Projections

Extending Past The Face Of The Fireplace

2 IN.

MINIMUM 3 FT. MAXIMUM

6 IN.

MINIMUM

Figure 5.5 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Non-combustibleMantel Legs Or Wall Projections Extending Past The Face Of The Fireplace

3 IN.

MINIMUM UNLIMITED

Figure 5.6 Non-CombustibleMantel Leg or Wall Projections

Î

(Acceptable on both sides of opening)

 

Front Side Finishing Detail

 

1.00 in.

 

FRAMING

 

1-9/16in.

 

1/2 in. BUILDING MATERIAL

Figure 5.7

Front Side Finishing Detail

2143-900Rev. B • 7/08

1/2 in.

SHEETROCK

3-1/2in.

NON-COMBUSTIBLE

BOARD SHIPPED

WITH APPLIANCE

1 in.

1-9/16in.AIR SPACE

Figure 5.8 Non-CombustibleZone

Heat & Glo • SLR • 2143-900Rev. B • 7/08

19

6 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Maintain vent clearance to combustibles as specified.

DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and fire.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12.................................................1.25*

Over 7/12 to 8/12.................................................1.5*

Over 8/12 to 9/12.................................................2.0*

Over 9/12 to 10/12...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12.............................................5.0

Over 14/12 to 16/12.............................................6.0

Over 16/12 to 18/12.............................................7.0

Over 18/12 to 20/12.............................................7.5

Over 20/12 to 21/12.............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge

Opening

 

 

DIRECT VENT GAS, WOOD OR FUEL

OIL TERMINATION

B

C

A

GAS

TERMINATION

 

 

Minimum Dimensions

 

Termination

Wood & Fuel Oil

Comments

 

 

Termination

 

A

6 in.

20 in.

Horizontal distance between terminations

B

20 in.

24 in.

Distance to perpendicular wall

C

18 in.

18 in.

Vertical distance between terminations

 

 

 

 

Figure 6.2 Staggered Termination Caps

DIRECT VENT GAS, WOOD OR FUEL

OIL TERMINATION

 

 

20 IN.

 

 

(508 MM)

 

 

(MINIMUM) TO

 

20 IN. MIN. *

PERPENDICULAR

WOOD OR

WALL

(508 MM)

GAS TERMINATION

(GAS ONLY)

 

*IF USING DECORATIVE CAP COVER(S), THIS DISTANCE MAY NEED TO BE INCREASED. REFER TO THE INSTALLATION INSTRUCTIONS SUPPLIED WITH THE DECORATIVE CAP COVER.

Figure 6.3 Leveled Termination Caps

20

Heat & Glo • SLR • 2143-900Rev. B • 7/08

 

 

 

E

 

 

 

 

C

 

 

A

 

F

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

J

B

 

 

 

U.S

 

 

 

 

 

 

 

 

 

V

V

B

 

 

 

 

B

(3 FT.)

 

 

 

 

V

 

 

 

 

 

i

 

 

 

 

 

 

 

 

 

 

 

 

D

V

V

 

G

M

X

 

 

 

A

 

 

V

H OR i

 

 

O

 

 

 

V

 

 

 

 

 

N

 

 

 

 

P

 

L

 

 

R

 

 

 

V

K

Electrical

K

V

 

 

 

 

Service

 

C

Q

V

(See Note 2)

Measure vertical clearances from this surface.

 

V

= VENT TERMINAL

X = AIR SUPPLY INLET

A

=

12 inches.................

clearances above grade, veranda,

 

 

 

(See Note 1)

porch, deck or balcony

B

=

12 inches.................

clearances to window or door

 

 

 

 

that may be opened, or to perma-

 

 

 

 

nently closed window. (Glass)

C

=

18 inches.................

vertical clearance to unventilated

 

 

 

 

soffit or to ventilated soffit located

 

 

 

 

above the terminal

 

 

 

30 inches .................

for vinyl clad soffits and below

 

 

 

 

electrical service

D

=

9 inches..................

clearance to outside corner

E

=

6 inches...................

clearance to inside corner

F

=

3 ft. (Canada)..........

not to be installed above a gas

 

 

 

 

meter/regulator assembly within 3

 

 

 

 

feet (90 cm) horizontally from the

 

 

 

 

center-lineof the regulator

G

=

3 ft...........................

clearance to gas service regulator

H

=

9 inches (U.S.A.)

vent outlet

 

 

 

 

12 inches (Canada) clearance to non-mechanical

 

 

 

 

air supply inlet to building or the

 

 

 

 

combustion air inlet to any other

i

=

3 ft. (U.S.A.)

appliance

 

 

 

 

6 ft. (Canada)...........

clearance to a mechanical (pow-

 

 

 

(See Note 1)

ered) air supply inlet

**a vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

***only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor, or meets Note 2.

Note 1: On private property where termination is less than 7 feet above a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap shield is suggested. (See vents components page)

Note 2: Termination in a covered alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions specified for vinyl ornon-vinylsiding and soffits.1. There must be 3 feet minimum between termination caps.2. All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below the termination cap.3. All gravity air intakes within 3 feet of a termination cap must be a minimum of 1 foot below the termination cap.

Figure 6.4 Minimum Clearances for Termination

Measure horizontal clearances from this surface.

= AREA WHERE TERMINAL IS NOT PERMITTED

J**

=

7 ft..........................

clearance above paved

 

 

(See Note 1)

sidewalk or a paved driveway

 

 

 

located on public property

K

=

6 inches.................

clearance from sides of electri-

 

 

(See Note 5)

cal service

L

=

12 inches................

clearance above electrical

 

 

(See Note 5)

service

Covered Alcove Applications

M*** =

18 inches .............

clearance under veranda, porch,

 

 

 

 

deck, balcony or overhang

 

 

42 inches

......... vinyl

 

 

N

=

6 inches ...........

non-vinylsidewalls

 

 

12 inches .........

vinyl sidewalls

O

=

18 inches .........

non-vinylsoffit and overhang

 

 

42 inches .........

vinyl soffit and overhang

P

=

8 ft.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QMIN

RMAX

 

 

1 cap

 

3 feet

2 x Q ACTUAL

 

 

2 caps

 

6 feet

1 x Q ACTUAL

 

 

3 caps

 

9 feet

2/3 x Q ACTUAL

 

 

4 caps

 

12 feet

1/2 x Q ACTUAL

 

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

Note 3: Local codes or regulations may require different clearances.

Note 4: Termination caps may be hot. Consider their proximity to doors or other traffic areas.

Note 5: Location of the vent termination must not interfere with access to the electrical service.

In the U.S and Canada: Vent system termination is NOTpermitted in screened porches.

Vent system termination is permitted in porch areas with two or more sides open. You must follow all side walls, overhang and ground clearances as stated in the instructions.

Heat & Glo assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

21

7 Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home Technologies SLP venting systems. Refer to Section 16B for vent component information.

DO NOT mix pipe, fittings or joining methods from different manufacturers.

The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOTvent to a pipe serving a separate solid fuel burning appliance.

NOTICE: TheSLP-HRC-SSandSLP-HRC-ZC-SSterminationcaps are NOT approved for use with propane fuel.

B. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

 

 

V1

First section (closest to appliance) of vertical length

 

 

V2

Second section of vertical length

 

 

H1

First section (closest to appliance) of horizontal length

 

 

H2

Subsequent sections of horizontal length

 

 

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2in. (216 mm) horizontal run and8-1/2in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1).

Vertical

 

in.

 

 

 

 

.

 

 

1/2-8

 

12

in

 

 

8-1/2in.

Horizontal

Figure 7.1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

Pipe measurements are shown using the effective length of pipe (see Figure 7.2).

Measurements are made from the appliance outer wrap, not from the standoffs.

Horizontal terminations are measured to the outside mounting surface (flange of termination cap).

Vertical terminations are measured to bottom of termination cap.

Horizontal pipe installed level with no rise.

A

B

1-1/4in. (32 mm) OVERLAP

Figure 7.2 Chimney Offset/Return

 

Effective Height/Length

 

Pipe

inches

mm

 

SLP4

4

102

Effective

SLP6

6

152

SLP12

12

305

Height/

SLP24

24

610

Length

SLP36

36

914

 

 

SLP48

48

1219

 

SLP6A

2 - 6

51 - 152

 

SLP12A

2 - 12 51 - 305

Figure 7.3 SLP Pipe Effective Length

 

Î

E. Vent Diagrams

General Rules:

When penetrating a combustible wall, a wall shield firestop must be installed.

When penetrating a combustible ceiling, a ceiling firestop must be installed.

Horizontal runs of vent do not require vertical rise; horizontal runs may be level.

22

Heat & Glo • SLR • 2143-900Rev. B • 7/08

WARNING

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between ceiling firestops.

ALWAYS maintain specified clearances around venting and firestop systems.

Install wall shield and ceiling firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

Top Vent - Horizontal Termination

Venting with 1 elbow

V Minimum

H1 Maximum

SLR

 

 

 

 

 

 

90 Elbow

1-1/2ft.

610 mm

 

 

 

 

1 ft.

305 mm

3 ft.

914 mm

 

 

 

 

2 ft.

610 mm

5 ft.

1.5 m

 

 

 

 

3 ft.

914 mm

7 ft.

2.1 m

 

 

 

 

4 ft.

1.2 m

14 ft.

4.3 m

 

 

 

 

H MAX. =14 ft. (4.3 m)

V + H MAX. = 40 ft. (12.2 m)

H1

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

Note: TheSLP-HRC-SSandSLP-HRC-ZC-SStermination caps are not approved for use with propane (LP) fuel.

V1

Figure 7.4

Heat & Glo • SLR • 2143-900Rev. B • 7/08

23

1. Top Vent - Horizontal Termination - (continued)

Top Vent - Horizontal Termination

Venting with 2 elbows

 

V Minimum

H1 + H2 MAXIMUM

 

 

SLR

 

 

 

 

 

90° Elbow

1 ft.

 

305 mm

 

 

 

 

 

 

1 ft.

 

305 mm

2 ft.

 

610 mm

 

 

 

 

 

 

2 ft.

 

610 mm

4 ft.

 

1.2 m

 

 

 

 

 

 

3 ft.

 

914 mm

6 ft.

 

1.8 m

 

 

 

 

 

 

4 ft.

 

1.2 m

14 ft.

 

4.3 m

 

 

 

 

 

 

H + H1 MAX. =14 ft. (4.3 m)

V + H + H1 MAX. = 40 ft. (12.2 m)

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

Note: TheSLP-HRC-SSandSLP-HRC-ZC-SStermination caps are not approved for use with propane (LP) fuel.

H2

V1

H1

 

INSTALLED

HORIZONTALLY

Figure 7.5

24

Heat & Glo • SLR • 2143-900Rev. B • 7/08

1. Top Vent - Horizontal Termination - (continued)

 

 

 

 

 

 

Top Vent - Horizontal Termination

 

 

 

 

 

 

 

Venting with 3 elbows

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLR

 

 

 

V1 Minimum

H1 + H2 Maximum

V2

V1 + V2 Minimum

 

90° Elbow

6 ft.

 

 

 

1.8 m

*

*

 

1 ft.

305 mm

10 ft.

 

 

 

3.0 m

*

*

 

2 ft.

610 mm

12 ft.

 

 

 

3.7 m

*

*

 

3 ft.

914 mm

14 ft.

 

 

 

4.3 m

*

*

 

 

 

H1

+ H2

MAX. =14 ft. (4.3 m)

 

 

 

 

V1 + V2 + H1

+ H2 MAX. = 40 ft. (12.2 m)

 

 

*No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)

 

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

Note: TheSLP-HRC-SSandSLP-HRC-ZC-SStermination caps are not approved for use with propane (LP) fuel.

H2

V2

H1V1

Figure 7.6

Heat & Glo • SLR • 2143-900Rev. B • 7/08

25

1. Top Vent - Horizontal Termination - (continued)

Top Vent - Horizontal Termination

Venting with 3 elbows

 

 

V Minimum

H1 + H2 + H3 MAXIMUM

 

 

SLR (NG ONLY)

 

 

 

 

 

 

90° Elbow

ft.

mm

 

 

 

 

 

 

 

3 ft.

 

914 mm

15 ft.

4.6 m

 

 

 

 

 

 

Î

 

 

H1 + H2 + H3 MAX. =15 ft. (4.6 m)

 

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

Note: This venting configuration is approved ONLY for Natural Gas models.

H2

H1

H3

V1

Figure 7.7

26

Heat & Glo • SLR • 2143-900Rev. B • 7/08

Top Vent - Vertical Termination

No Elbows

V1 = 44 ft. Max. (13.4 m)

Note: If installing a vertical vent/termination off the top of the appliance, the optional exhaust restrictor may be needed.

Note: Use SLP Series components only.

V1

Figure 7.8 Vertical Vent Maximum

Exhaust restrictors are recommended for these vertically terminated products which have excessive draft. Exhaust restrictors will compensate for high draft, and restore visual flame height. If the vent configuration has a total vertical of 15-44feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance manual bag.

Exhaust restrictor Instructions

1.Locate the two pilot holes located in the inside firebox heat shield as shown in Figure 7.8.

2.Center the exhaust restrictor such that the thru holes in the vent restrictor align with the pilot holes in the restrictor.

3.Use (2) ½” self-piercingscrews to secure vent restrictor to firebox heat shield. See Figure 7.9

PILOT HOLES

Figure 7.9 Location of Pilot Holes

Figure 7.10 Exhaust Restrictor Installation

4.In some applications, such as those where the fireplace is elevated off the floor, the vent restrictor may be painted, but painting is not required.

Notice: Before painting, contact your dealer for information on the appropriate high temperature paint.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

27

Top Vent - Vertical Termination

Venting with 2 elbows

 

 

 

 

 

SLR

 

 

 

V1 Minimum

H Maximum

 

V2

V1 + V2 Minimum

 

 

90° Elbow

2 ft.

610 mm

 

*

*

 

1 ft,

 

152 mm

3 ft.

914 mm

 

*

*

 

2 ft.

 

457 mm

5 ft.

1.5 m

 

*

*

Î

3 ft.

 

914 mm

7 ft.

2.1 m

 

*

*

 

4 ft.

 

1.1 m

15 ft.

4.6 m

 

*

*

 

 

 

 

H MAX. =15 ft. (4.6 m)

 

 

 

 

 

 

V1 + V2 + H MAX. = 40 ft. (12.2 m)

 

 

 

 

* No specific restrictions on this value EXCEPT V1 + V2 + H cannot exceed 40 ft. (12.2 m)

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 7.3).

V2

V1

H1

Figure 7.11

28

Heat & Glo • SLR • 2143-900Rev. B • 7/08

Top Vent - Vertical Termination

Venting with 3 elbows

 

 

 

SLR

 

 

Î

V1 Minimum

H1 + H2 Maximum

V2

V1 + V2 Minimum

 

90° Elbow

1 ft.

305 mm

*

*

1 ft.

305 mm

2 ft.

610 mm

*

*

2 ft.

610 mm

4 ft.

1.2 m

*

*

3 ft.

914 mm

6 ft.

1.8 m

*

*

4 ft.

1.2 m

14 ft.

4.3 m

*

*

 

 

H MAX. =14 ft. (4.3 m)

 

 

 

 

V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)

 

 

* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)

 

 

Note: Use SLP Series

 

 

 

 

components only.

 

 

 

 

Note: ThereMUST be a 25%

 

 

 

 

reduction in total H when using

 

 

 

V2

flex vent except when using the

 

 

 

simple up and out installation

 

 

 

 

 

 

 

 

(see Figure 7.3).

 

 

H1

H2

V1

 

 

INSTALLED

 

HORIZONTALLY

Figure 7.12

Heat & Glo • SLR • 2143-900Rev. B • 7/08

29

Top Vent - Vertical Termination

Venting with 4 elbows

Note: Use SLP Series components only.

Note: ThereMUST be a 25% reduction in total H when using flex vent except when using the simple up and out installation (see Figure 5.3).

V1 MIN.

 

H1 MAX.

V2 MIN.

H2 MAX.

V3 MIN.

 

 

 

 

 

 

 

 

 

 

 

1-1/2ft.

457 mm

 

4 ft.

1.2 m

4 ft.

1.2 m

4 ft.

1.2 m

3-1/2ft.

1.0 m

 

 

 

 

 

 

 

 

 

 

 

 

 

V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)

 

 

V3

V2

H2

H1

V1

Figure 7.13

30

Heat & Glo • SLR • 2143-900Rev. B • 7/08

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent.DO NOT pack insulation or other combustibles:

Between ceiling firestops

Between wall shield firestops

Around vent system

Failure to keep insulation or other material away from vent pipe may cause over heating and fire.

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).

SLP heat shield - designed to be used on a wall4-3/8in. to7-5/8in. (111 mm to 194 mm thick).

If wall thickness is less than 4-3/8the existing heat shields must be field trimmed. If wall thickness is greater than7-5/8in. aDVP-HSM-Bwill be required.

 

(SLP Pipe Shown)

 

Heat

3 in. (76 mm)

Shield

top clearance

 

1 in. (25 mm)

 

clearance around

 

vertical sections

 

 

Wall

 

Shield

 

Firestop

 

WALL

3 in. (76 mm) top clearance *

Heat

Shield

1 in. (25 mm) clearance bottom & sides

* When using SLP pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are: Top: 2-1/2in. (64 mm)

Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm)

Figure 8.1 Horizontal Venting Clearances To Combustible

Materials

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield firestop(s). The wall shield firestop maintains minimum clearances and prevents cold air infiltration.

The opening must be framed on all four sides using the

 

 

same size framing materials as those used in the wall

 

 

construction.

 

• SLP pipe - A wall shield firestop must be placed on each

 

 

side of an interior wall. A minimum 1-1/2in. (38 mm)

 

 

overlap of attached heat shields must be maintained.

 

See Section 10.L. for information for regarding the in-

Î

 

stallation of a horizontal termination cap.

 

Non-CombustibleWall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one in. greater than the pipe is acceptable.

Whenever a non-combustiblewall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.

DO NOT PACK WITH

INSULATION OR

OTHER MATERIAL

10 in.

10 in.

B

A

A*

B

Î

48-1/16in.

47-1/16in.

*Shows center of vent framing hole for top venting. The center of the hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.

Figure 8.2 Wall Penetration

Heat & Glo • SLR • 2143-900Rev. B • 7/08

31

C. Install the Ceiling Firestop

A ceiling firestop MUST be used between floors and attics.

SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.4).

Frame the area with the same sized lumber as used in ceiling/floor joist.

The ceiling firestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between floors that are not insulated. Refer to Figure 8.5.

Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu- lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

 

 

ATTIC ABOVE

 

 

A

 

 

A

 

PIPE

A

 

SLP

9 in. (229 mm)

Figure 8.4

Installing Ceiling Firestop

 

 

INSTALL ATTIC INSULATION SHIELDS

 

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

 

3 FASTENERS

 

 

PER SIDE

 

 

CEILING FIRESTOP

CEILING FIRESTOP

 

INSTALLED BELOW CEILING

INSTALLED ABOVE CEILING

 

Figure 8.5 Installing the Attic Shield

 

32

Heat & Glo • SLR • 2143-900Rev. B • 7/08

 

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specified clearance and be secured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Vaulted Ceiling Installation

The attic insulation shield has been laser-etchedwith cut lines and ceiling pitches to make field trimming easier.

Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Cut the attic insulation shield (if application is for vaulted ceiling) using a laser-etchedcut line, to fit your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90°

TO MAINTAIN CLEARANCE

AND PREVENT INSULATION

FROM FALLING INSIDE

LASER-ETCHED

INSERT 3 CUT LINES

SCREWS

BEND 3 TABS

OUTWARD TO

FASTEN TO CEILING

FIRESTOP-BEND

REMAINING TABS

INWARD 90 DEGREES

TO MAINTAIN

CLEARANCE

Figure 8.6 Attic Insulation Shield

Heat & Glo • SLR • 2143-900Rev. B • 7/08

33

9 Appliance Preparation

A. Top Vent

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

ELBOW HEAT SHIELD SHOWN

IN SHIPPING POSITION

Figure 9.1 Elbow Shield Shown as Shipped

ELBOW HEAT SHIELD

SHOWN AS INSTALLED

PIPE GASKET

Figure 9.2 Elbow Shield Shown Installed

If venting with a 90 degree elbow directly off of the top of the appliance, the elbow heatshield must be repositioned as shown in Figure 9.2.

If venting vertically or using a straight seciton of vertical pipe, remove the elbow heat shield and discard by removing the two 1/4 in. screws that secure the elbow heat shield to the top of the fireplace.

For all venting applications, ensure that the pipe gasket is in place before attaching any pipe section. This gasket is shipped in place around the starting collar. See Figure 9.2.

34

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

Sagging or loose insulation

Insulation backing or plastic

Framing and other combustible materials

Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs. Failure to maintain air space clearance may cause overheating and fire.

For details on setting the appliance in the framing, refer to section 13.A. The diagram shows how to properly position, level, and secure the appliance (see Figure 9.3). Nailing tabs are provided to secure the appliance to the framing members.

Bend out nailing tabs on each side.

Place the appliance into position.

Keep nailing tabs flush with the framing.

Level the appliance from side to side and front to back.

Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

Secure the appliance to the framing by using nails or screws through the nailing tabs.

Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

Figure 9.3 shows the fireplace installed on the floor. However, this fireplace can be elevated off the floor provided that the fireplace is properly supported by framing materials and the ceiling clearances are maintained.

NAILING TABS

BOTH SIDES

Figure 9.3 Proper Positioning, Leveling And Securing Of An

Appliance

Heat & Glo • SLR • 2143-900Rev. B • 7/08

35

10 Installing Vent Pipe (SLP Pipe)

A. Assemble Vent Sections

To attach the first vent component to the starting collars of the appliance:

Lock the vent components into place by sliding the pipe section onto the collar.

Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 10.1.

Slide the gasket over the first vent section and place it flush to the appliance. This will prevent cold air infiltration. High temperature caulk may be used to hold the part in place.

Continue adding vent components, locking each succeeding component into place.

Ensure that each succeeding vent component is securely fitted and locked into the preceding component.

Commercial, Multi-family(Multi-levelexceeding two stories), orHigh-RiseApplications

For Installation into a commercial, multi-family(multi-levelexceeding two stories) orhigh-riseapplications: All outer pipe joints must be sealed with high temperature silicone, including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 10.2

Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 10.1 Adding Venting Components

Figure 10.2 High Temperature Silicone Sealant

36

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Assemble Slip Sections

Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 10.3.

Slide together to the desired length.

Pilot hole

Figure 10.3 Slip Section Pilot Holes

Maintain a 1-1/2in. (38 mm) overlap between the slip section and the pipe section.

Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 10.4.

Figure 10.4 Screws into Slip Section

Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a high temperature silicone sealant.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

Only outer pipes are sealed, sealing the inner flue is not required.

All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed.

C.Secure The Vent Sections

Vertical runs of pipe must be supported every 8 ft. (2.44 m).

Horizontal sections must be supported every 5 feet (1.52 m).

Vent supports or plumbers strap (spaced 120º apart) may be used to support. See figures 10.5 and 10.6.

Wall shield firestops may be used to provide horizontal support.

Ceiling firestops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

Figure 10.5

Securing Vertical Pipe Sections

Î

Figure 10.6 Securing Horizontal Pipe Sections

Î

Heat & Glo • SLR • 2143-900Rev. B • 7/08

37

D. Disassemble Vent Sections

Rotate either section (see Figure 8.7) so the seams on both pipe sections are aligned as shown in Figure 10.8.

Pull carefully to separate the pieces of pipe.

Figure 10.7 Rotate Seams for Disassembly

Figure 10.8 Align and Disassemble Vent Sections

E. Install Decorative Ceiling Components

A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling thimble is used to cover the firestop.

Seal the gap between the vent pipe and firestop using high temperature silicone to prevent cold air infiltration.

Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.

A decorative cathedral ceiling support box can be installed on a cathedral ceiling through which the vent passes.

Use a plumb-bobto mark the center line of the venting system on the ceiling and drill a small hole through the ceiling and roof at this point. Locate the hole and mark the outline of the cathedral ceiling support box on the outside roof.

Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure 10.9).

Level the support box both vertically and horizontally and temporarily tack it in place through the inside walls into the roof sheathing.

Use tin snips to cut the support box from the top corners down to the roof line and fold the resulting flaps to the roof. See Figure 10.10.

Nail the flaps to the roof AFTER running a bead of non hardening sealant between the flaps and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

LEVEL

CATHEDRAL CEILING

SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm)

GREATER IN SIZE THAN

PATTERN OF SUPPORT

BOX AS IT IS PROJECTED

ONTO ROOF LINE

Figure 10.9

Figure 10.10

38

Heat & Glo • SLR • 2143-900Rev. B • 7/08

F. Install Metal Roof Flashing

Note: Skip this section if using theRF4-8.

See minimum vent heights for various pitched roofs (Figure 10.11) to determine the length of pipe to extend through the roof.

Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 10.12.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12............................1.25*

Over 7/12 to 8/12..............................1.5*

Over 8/12 to 9/12..............................2.0*

Over 9/12 to 10/12............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12........................... 5.0

Over 14/12 to 16/12........................... 6.0

Over 16/12 to 18/12........................... 7.0

Over 18/12 to 20/12........................... 7.5

Over 20/12 to 21/12........................... 8.0

* 3 foot minimum in snow regions

Figure 10.11 Minimum Height From Roof To Lowest Discharge

Opening

 

 

NOTICE: Failure to properly caulk the roof flashing could cause water entry.

Caulk the gap between the roof flashing and the outside diameter of the pipe.

Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 10.12.

CAULK

Figure 10.12

G. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Connect both halves of the storm collar with two screws (see Figure 10.13).

Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 10.14).

Caulk around the top of the storm collar (see Figure 10.20).

Figure 10.13 Assembling the Storm Collar

Figure 10.14 Assembling the Storm Collar Around the Pipe

Heat & Glo • SLR • 2143-900Rev. B • 7/08

39

H. Install RF4-8

The RF4-8may be used in place of the roof flashing and

Îstorm collar (Sections 10.F and Section 10.G.)

Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FSwhen using theRF4-8Flashing. Refer to Sect. 10.C Securing Vent Sections.

SECURE WITH 4

SCREWS NO LONGER

THAN 1 IN. (25 MM)

SLP-FS

Figure 10.15 Secure Pipe with SLP-FS

Trim the rubber boot (using scissors or a utility knife), cutting along the marked measurement lines. See Figure 10.16. Use the 150 mm line.

Lubricate pipe or flue with water and slide the flashing down. It may be necessary to trim the top shingles around the base of the rubber boot to ensure a good fit.

Draw around flashing, remove.

Apply silicone sealant to roof inside the lines (Figure 10.17)

Lubricate pipe or flue with water and slide flashing down. Seat firmly in sealant. Nail roof flashing to the roof.

Apply silicone sealant on the top outside of the base plate on the sides and on top edge. See Figure 10.18. Install shingles, Apply sealant at the top edge of the rubber boot. See Figure 10.19.

We recommend that you top coat with conventional acrylic house paint to improve the appearance of your galvanized base flashing.

Figure 10.16 Trim Rubber Boot

40

Heat & Glo • SLR •

Figure 10.17 Apply Sealant

APPLY SEALANT

TOP & PARTIAL SIDES

Figure 10.18 Slide Flashing Down, Secure & Apply Sealant

SILICONE SEALANT (TOP OF BOOT)

SHINGLES TRIMMED

FLASHING OVER

SHINGLES OVER

SHINGLES

FLASHING

 

Figure 10.19 Installation Complete

2143-900Rev. B • 7/08

I. Install Vertical Termination Cap

Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

Secure the cap by driving three self-tappingscrews (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 10.20).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 10.20

J. Install Decorative Wall Components

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the firestop.

Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 10.21.

K.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.

DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 10.22).

Heat shields must overlap 1-1/2in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attachedto the wall shield firestop. The other section isfactory-attachedto the cap. See Figure 10.22.

If the wall thickness does not allow the required 1-1/2in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

If the wall thickness is less than 4 in./102 mm (DVP) or 4-3/8in./ 111 mm (SLP), the heat shields on the cap and wall shield firestop must to be trimmed. A minimum1-1/2in. (38 mm) overlap MUST be maintained.

Use an extended heat shield if the finished wall thickness is greater than 7-1/4in. (184 mm).

The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2in. (38 mm) overlap between heat shields.

Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields maynot be field constructed.

Figure 10.21 Wall Thimble

Heat & Glo • SLR • 2143-900Rev. B • 7/08

41

L. Install Horizontal Termination Cap

WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent.

1-1/2(38 MM) MINIMUM OVERLAP OF FLUE TELESCOPING SECTION IS REQUIRED.

FAILURE TO MAINTAIN OVERLAP MAY CAUSE OVERHEATING AND FIRE.

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at outside edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current

ANSI Z223.1 and CAN/CGA-B149installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

NOTICE: For certain exposures which require superior resistance towind-drivenrain penetration, a flashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps withfactory-suppliedheat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

HEAT SHIELD

EXTENDED

1-1/2IN. (38 MM) MIN.

HEAT SHIELD

OVERLAP

WALL SHIELD

 

FIRESTOP

 

SLIP SECTION

 

CAN BE EXTENDED

 

INNER VENT

SHEATHING

OUTER VENT

 

INTERIOR

EXTERIOR

Figure 10.22 Venting through the wall

 

42

Heat & Glo • SLR • 2143-900Rev. B • 7/08

11 Gas Information

A. Fuel Conversion

Make sure the appliance is compatible with available gas types.

Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressure

Optimum appliance performance requires proper input pressures.

Gas line sizing requirements will be determined in ANSI Z221.3 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

Pressure requirements are:

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

14.0 in. w.c.

14.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

SCREW LOCATIONS (16)

DO NOT REMOVE

THESE FOUR SCREWS

Figure 11.1 Basepan Removal

ACCESS TO

MANUAL SHUTOFF

VALVE AND

JUNCTION BOX

LOWER COVER

PANEL

VALVE

ASSEMBLY

Figure 11.2 Gas and Electrical Access

Note: This appliance does include a manual gas shutoff valve that is located in the valve compartment. This manual gas shutoff valve is accessible for service by removing the basepan and burner assembly. See Figure 11.1.

The lower access cover panel is removable if finishing material is not installed.

There is an access plate located on the left side of the firebox bottom. See Figure 11.2. Remove screws and plate to access the manual shutoff valve included with this fireplace. See Figure 11.3 and Figure 11.4. Depending upon local code, an additional manual gas shutoff, in an easily accessible area may be required and located upstream from the appliance.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Î

Heat & Glo • SLR • 2143-900Rev. B • 7/08

43

Figure 11.3 Gas Fitting Access

Figure 11.4 Gas Fitting and Junction Box Access

C. Gas Connection

Refer to Reference Section 16 for location of gas line access in appliance.

Gas line may be run through knockout(s) provided.

The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed with non-combustible,unfaced insulation to prevent cold air infiltration.

Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

Pipe incoming gas line into valve compartment.

Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.

Purge should be performed by qualified service technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all fittings and connections with a non-corrosivecommercially availableleak-checksolution.DO NOT use open flame. Fittings and connections could have loosened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce burner orifice 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce burner orifice 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

44

Heat & Glo • SLR • 2143-900Rev. B • 7/08

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric

Code CSA C22.1.

Wire the appliance junction box to 110-120VAC. This is required for use of optional accessories (standing pilot ignition) or proper operation of the appliance (Intellifire ignition).

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

B. Intellifire Ignition System Wiring

Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figure 12.2, Intellifire Pilot Ignition (IPI) Wiring Diagram.

This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

Plug the 3-voltAC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

C. Optional Accessories Requirements

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

Optional Remote Control Receiver and Battery Pack

Location

Batteries are to be installed only when battery power is

Î

 

required. Because of the limited accessibility to valve

 

cavity, the position of the Battery Tray, IPI Control Module,

 

and Optional Remote Control Receiver locations must be

 

installed as shown in Figure 12.1.

 

The Battery Tray, Control Module, and Remote Control

 

receiver can be accessed thru the air space between the

 

firebox front and the lower-frontfinishing cover panel. The

 

decorative front and glass assembly must be removed to

 

access these components.

 

The battery tray is attached with velcro to the inside of

 

the lower cover panel. The IPI control module and the

 

remote control receiver are placed on the firebox bottom.

 

FIREBOX BOTTOM

BATTERY TRAY

IPI CONTROL MODULE

REMOTE CONTROL RECEIVER

LOWER ACCESS PANEL

Figure 12.1 Valve Cavity

Heat & Glo • SLR • 2143-900Rev. B • 7/08

45

HOT

NEUTRAL

BATTERY PACK

IGNITION MODULE 3 VAC

INTERMITTENT PILOT IGNITOR

I

S

TRANSFORMER

WHITE

3 VAC

PLUG IN

BLACK

RED

ORANGE

GROUND TO

FIREPLACE

CHASSIS

WIRES

(TO BROWN)

ORANGE

GREEN

THERMOSTAT

WIRE ASSEMBLY

VALVE

Figure 12.2 Intellifire Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with batteryback-up.

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

E. Junction Box Installation

1.Remove the two screws that hold the junction box bracket to the right corner of the fireplace.

2.Remove the one screw that secures the junction box to the junction box bracket.

3.Route the wire through the strain relief in the outer wrap and down through the strain relief on left side of the junction box bracket and up through the right strain relief. See Figure 12.3.

4.Make the connection inside the junction box to the 120V wire. Connect green to the ground nut, black to black and white to white.

5.Reattach junction box to junction box bracket with one screw.

6.Reattach the junction box bracket to the appliance with two screws.

NOTE: There is an alternative access to the junction box.

Î

This can be accessed by removing the valve assembly.

 

See Figure 11.2.

 

 

 

JUNCTION BOX

BRACKET

NOTICE: DO NOT wire

110 VAC to wall switch.

Figure 12.3 Junction Box Detail

In the event that the junction box needs to be accessed

Î

or installed after finish methods have been applied, ac-

 

cess is possible by removing the valve assembly. See

 

Fig. 11.2. Bend the top heat shield back and remove the

 

one screw that secures the junction box to the bracket.

 

Ensure the heat shield is bent back so that it is positioned

 

above the junction box.

 

46

Heat & Glo • SLR • 2143-900Rev. B • 7/08

13 Finishing

A. Framing and Finishing Instructions

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause fire.

Finishing Instructions

It is important to follow the framing and finishing instructions to ensure proper placement of fireplace into the surrounding framing/finishing materials.

Wall sheathing materials 1/2 in. thick are specified in this installation manual to properly align with the factoryinstalled non combustible material

WARNING! Risk of Fire! DO NOT, under any circumstances, remove the factory-installed noncombustible board or cover it with any combustible material, such as:

Drywall (gypsum board)

Plywood

Or other materials that do not meet the ASTM E 136 Non-combustibilitystandard. See specification below

Failure to comply with these instructions may cause a fire or cause the appliance to overheat.

Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

Setting the Fireplace into the Framing

Unlike many traditional, single-sidedHeat & Glo fireplaces, this fireplace is recessed into surround framing. The left and right nailing tabs were designed for the SLR model as a means to ensure the fireplace is recessed to the correct location within the framing materials.

1.Bend three nailing tabs away from fireplace 180 degrees on both left and right nailing tabs. Do not adjust the column standoffs. See Figure 13.1 and Figure 13.2.

2.Screw each nailing tab to the adjoining framing material. Ensure that the 1” air space clearance is maintained on the sides of the fireplace. See Figure 13.3.

Top Flange

Top Flange

Factory-Installed

Factory-Installed

Non-Combustible

Board

Non-Combustible

 

Board

NAILING TABS

 

DO NOT ADJUST

Figure 13.1 Nailing Tabs

Figure 13.2 Nailing Tabs

Shipping Position

Installation Position

1.00 in.

FRAMING

1-9/16in.

1/2 in. BUILDING MATERIAL

Figure 13.3 Front Side Finishing Detail

Heat & Glo • SLR • 2143-900Rev. B • 7/08

47

WARNING! Risk of Fire! Maintain specified air space clearances to combustibles.

Failure to comply with these instructions may cause a fire or cause the appliance to overheat.

Ensure that the one inch back clearance and one inch side clearances are maintained.

 

TOP FLANGE

 

NON-COMBUSTIBLEBOARD

 

(PROVIDED WITH UNIT)

 

FINISHING FLANGES

 

LOWER COVER PANEL

 

NO

 

SCREWS

 

SIDE COLUMNS

Figure 13.4

Finishing Details

CAUTION! RISK OF GLASS DAMAGE AND CUTS! DO NOT DRILL OR INSTALL ANY TYPE OF SCREW OR FASTENER INTO THE LOWER COVER PANEL. SHARP SCREW OR FASTENER TIPS MAY PENETRATE AND BREAK THE GLASS OR CAUSE CUTS.

The SLR can be finished using either the Tonic or Martini decorative fronts. See Figures 13.17 and 13.18. Depending on the decorative front, the final fireplace installation can be accomplished by either the “overlap” or “inside-fit”method. Reference Section 13.C regarding installation details associated with the Inside and Overlap Fit methods.

If the final fireplace installation uses the Overlap Method, wall sheathing material ½” thick is specified and can be installed tight to the side finishing flanges. If the final fireplace installation uses the Inside-FitMethod, additional clearance of 4” must be maintained between combustible ½” thick wall sheathing material and the side finishing flanges. Reference Section 13.C regarding installation details associated with the Inside and Overlap Fit methods.

When finishing the wall around the fireplace, it is critical that wall sheathing be fastened properly. Wall sheathing fasteners, such as screws or nails, are not permitted in some locations. See Figure 13.4. It is acceptable to pre-drillholes and useself-tappedscrews in the factory-

installed non-combustibleboard which

may be used

to lathe (a backer for tile, marble, etc.)

Screws being

installed through the factory-installednon-combustibleboard should beself-tappingtype with a minimum length of 5” and maximum length of 7”. It is also acceptable to penetrate the top flange withself-tappingscrews. See Figure 13.4. Do not drill or install screws into the side columns as the existingstand-offswill support the wall sheathing. Do not drill or install screws which may penetrate the lower cover panel as this will restrict required access to the glass,battery-back-up,and remote receiver. See Figure 13.4.

The appliance is designed to accept ½” wall sheathing materials such as drywall, plywood, wood composites, or non-combustiblematerials. The type of material used depends whether the installation is an Inside or Overlap Fit method. Reference Section 13.C regarding installation details associated with the Inside an Overlap Fit methods. The left/right sides and bottom of the fireplace opening include finishing flanges that will interlock with ½” wall sheathing. See Figure 13.4. The ½” thick wall sheathing can be installed tight to the left, right, and bottom finishing flanges such that the rough edges of the sheathing are tucked behind the flanges. See Figure 13.5. It is necessary to cut a ½” slot in the sheathing where it is tucked tightly behind the lower finishing flange. See Figure 13.7.

Verify that the lover cover panel is installed correctly, and that the fireplace opening height is 16 in. See Figure 13.6.

NOTE: It is acceptable to use a high temperature silicone sealant to adhere drywall to lower cover panel.

FINISHING

FLANGES

Figure 13.5 Side Wall Sheathing Installed

Î

48

Heat & Glo • SLR • 2143-900Rev. B • 7/08

16 IN.

Figure 13.6 Confirm Fireplace Opening

Dimension

SIDE WALL

SHEATHING

1/2 INCH CUT IN LOWER WALL WALL SHEATHING SHEATHING

Figure 13.7 Lower Drywall Detail

Sealing Joints

The joints between the drywall sides and drywall above the top factory installed non-combustibleboard CAN NOT be sealed with a combustible drywall tape. Depending upon the final finishing method, use a minimum rated 300 degree sealant, drywall compound, or thin set to seal the side and top joints.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

49

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause fire.

Note: Fornon-combustiblefireplace finish material (marble, stone, etc) specifications refer to Figure 13.13 and Figure 13.15.

Combustible Mantels

1/2 in.

Thick Wall

Sheathing 12 in. MAX.

14 in. MEASUREMENT FROM TOP OF MIN. FIREPLACE OPENING

Figure 13.8 Clearances To Combustibles Mantels Or Other Combustibles Above Appliance

Non-combustibleMantels

1/2 in.

Thick Wall

Sheathing 12 in. MAX.

14 in. MEASUREMENT MIN. FROM TOP OF FIREPLACE

OPENING

Figure 13.9 Clearances To Non-CombustibleMantels Or Other

Non-CombustiblesAbove Appliance

Combustible Mantel Legs Or Wall Projections Extending Past The Face Of The Fireplace

2 IN.

MINIMUM 3 FT. MAXIMUM

6 IN.

MINIMUM

Figure 13.10 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Non-combustibleMantel Legs Or Wall Projections Extending Past The Face Of The Fireplace

3 IN.

MINIMUM UNLIMITED

Figure 13.11 Non-CombustibleMantel Leg or Wall Projections

Î

(Acceptable on both sides of opening)

 

50

Heat & Glo • SLR • 2143-900Rev. B • 7/08

C. Facing Material

Facing and/or finishing materials must not interfere with air flow through louvers, operation of louvers or doors, or access for service.

Facing and/or finishing materials must never overhang into the glass opening.

Observe all clearances when applying combustible materials.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

WARNING! Risk of Fire! DO NOT install drywall or other combustible materials over the factory-installed non-com- bustible board. Overlapping materials could ignite.

Decorative facing material thickness is measured from the face of the factory-installednon-combustibleboard. See Figure 13.12 and Figure 13.14.

FACTORY-INSTALLED

NON-COMBUSTIBLE

BOARD

NON-COMBUSTIBLEFINISHING MATERIAL0-1IN. THICK

TONIC DECORATIVE

FRONT SHOWN

NON-COMBUSTIBLEFINISHING MATERIAL0-1IN. THICK

DRYWALL OR EQUIVALENT (1/2 IN.)

Figure 13.12 Overlap Fit Method (Tonic or Martini Decorative Front)

Both the Tonic and Martini decorative fronts can be installed such that they overlap non-combustiblematerials up to 1 in. thick. See Figure 13.12 and Figure 13.13.

Additionally, the Tonic is approved to be installed in an inside fit application with up to 4 in. of non-combustiblematerial up to 4 in. thick. See Figure 13.14, Figure 13.15 and Figure 13.16.

Please refer to the appropriate section for specific requirements for each method if installation. See Figure 13.17 and Figure 13.18 for decorative front identification.

Non-CombustibleFinish Materials

0 - 1 inch thickness-OverlapFit Method

Both the Tonic and Martini decorative fronts are designed to overlap finish materials 0 inches to 1 inch thick. See Figure 13.12.

NOTICE: This one inch maximum not only includes the decorative finish materials (marble, tile, slate, etc) but also the thinset, lath and adhesive used to attach the decorative finish material.

The non-combustiblefinish material can be installed up to the 16 inch (height) by 43 inch (width) fireplace opening.

Top Joint

 

 

0 in.

Side

NON-COMBUSTIBLE

Side

Joint

BOARD

Joint

Bottom

Joint

Figure 13.13 Non-CombustibleFinish Material Diagram for0-1Inch Thick Overlap Fit Method (Tonic or Martini Decorative Front)

Heat & Glo • SLR • 2143-900Rev. B • 7/08

51

Non-CombustibleFinish Materials

0 Inches to 4 Inches Thick Inside Fit Method

Note: The Inside Fit application is only approved for the Tonic decorative front.

The Tonic decorative front is approved for inside fit applications. Non-combustiblefinishing materials up to 4 inches thick can be installed around the Tonic front (left, right, top, and bottom). The inside fit method requires an additional 4 in. of 1/2 in. thicknon-combustiblebuilding material (not supplied with fireplace) to be installed on the left and right sides flush with the factory installed noncombustible board. See Figure 13.15.

WARNING! Risk of Fire! The Martini decorative Front is not approved for inside fit installations.DO NOT install Martini decorative front using an inside fit application. Resulting elevated \temperatures may cause overheating and fire.

For the Tonic decorative front inside fit applications, the decorative front must be installed tightly to the finishing flanges and must not overlap any finish material.

Ensure that no non-combustiblefinish materials are installed within 3/4 in. of the fireplace opening. The 3/4 in. spacing is required to provide clearance for removing and installing the Tonic decorative front. See Figure 13.16.

FACTORY-INSTALLED

NON-COMBUSTIBLE

BOARD

0-4IN.

17-1/2IN. APPLIANCE OPENING (HEIGHT)

0- 4 IN.

DRYWALL OR EQUIVALENT (1/2 IN.)

Top Joint

0 in.

Non-Combustible

Finishing Material

 

4 in. MINIMUM

 

NON-COMBUSTIBLE

Side

BOARD

Joint

0 in.

Non-Combustible

 

Finishing Material

0 in.

4 in. MINIMUM

Bottom

Joint

Figure 13.15 Noncombustible Surface Finishing Material 0-4

Inches Thick-InsideFit Method (Tonic Decorative

Front Only)

Non-CombustibleFinish Material0-4Inches Thick

3/4 IN.

3/4 IN.

 

Bottom

 

Joint

Figure 13.16 Noncombustible Surface Finishing Material 0-4InchThick-InsideFit Method (Tonic Decorative Front Only)

Figure 13.14 Inside Fit Method (Tonic Decorative Front Only)

52

Heat & Glo • SLR • 2143-900Rev. B • 7/08

D. Decorative Fronts

WARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place.

Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used.

Inside and Overlap Fit

See Section 13.C.

TONIC DECORATIVE FRONT

(TN-SLR-**)

Figure 13.17 Tonic Decorative Front

Overlap Fit Only

See Section 13.C.

MARTINI DECORATIVE FRONT

(MT-SLR-**)

Figure 13.18 Martini Decorative Front

The tinted glass on the Martini Decorative Front meets the tempered glass specifications in Section 1.B of this installation manual.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

53

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14F.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox. The standard black rock media and manual bag assembly are also shipped underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

54

Heat & Glo • SLR • 2143-900Rev. B • 7/08

E. Rock Media Instructions

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

Cleaning the Rock

During shipment of the Rock Media, dust and debris can accumulate. It is recommended that the Rock Media be rinsed thoroughly with water to remove dust and small glass particles. An easy method to clean the Rock Media is to dump the rocks into a bucket and rinse thoroughly with a garden hose. Allow the rocks to dry before installing them into the fireplace.

INSTALLATION

1.Choose 7 - 10 flat, quarter-sized,pieces of Rock Media and set them aside. These will be used later to conceal the pilot cover. Reference Figure 14.1 for choosing flat pieces of glass.

NO YES

Figure 14.1. Selecting Flat Rocks for Pilot Cover.

ÎWARNING

Delayed Ignition Risk

Place stones according to instructions.

Do NOT place stones in area in front of pilot or between burner tracks.

Do NOT place stones in a position that they may fall into area in front of pilot.

Do NOT use any media other than the stones supplied with this fireplace.

Do NOT use more than one 10 lb. bag of rock media per fireplace.

Fireplace will not function properly.

Delayed ignition may occur.

2.Place an even layer of decorative rock around the base pan as shown in Figure 14.2. Do not place rocks in the slot over the burner ports. See Figures 14.2 and 14.3. This may cause lighting issues, undesirable burner flame, or delayed ignition.

BURNER PORT SLOT MUST BE FREE OF ROCKS

Figure 14.2. Place Rock Media

Î

WARNING! Risk of Fire. DO NOT place rock media directly in front of the pilot assembly or between the burner tracks over the burner ports..

3.Figure 14.4 shows an outline of the area in front of the pilot assembly. No rock media may be placed in the

outlined area. Continue to place an even amount of Rock Media over the entire base pan. DO NOT install Rock Media in between the tracks over the entire length of the burner.

DO NOT PLACE ROCK MEDIA

BETWEEN BURNER TRACKS

Figure 14.3. Burner Tracks

DO NOT PLACE ROCK MEDIA

IN FRONT OF PILOT ASSEMBLY

Figure 14.4. Pilot Bracket Detail

Î

Heat & Glo • SLR • 2143-900Rev. B • 7/08

55

4.The rock media placement jig must remain in place while media is placed on the basepan and around the pilot bracket.

5.Remove the rock media placement jig by removing the screw as noted in Figure 14.5.

SCREW

Figure 14.5. Remove Screw

6.Place the flat pieces of Rock Media that were sorted out in Step 1, carefully hide the pilot cover. See Figures 14.6 and 14.4.

Î Figure 14.6. Place Flat Pieces of Rock Media

56

Heat & Glo • SLR • 2143-900Rev. B • 7/08

F. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace as a complete assembly.

Removing Fixed Glass Assembly

1.Remove the decorative front.

2.Locate the two spring latches that are on the upper left and right of the fireplace.

3.Use both index fingers to release spring latches. See Figure 14.3.

4.Allow glass to tilt forward. Grasp glass on the upper right and left sides and lift glass “up” and “out.”

Replacing Fixed Glass Assembly

1.Locate glide tabs on lower left and right corners.

2.Grasp glass on upper right and left sides and tilt bottom of glass assembly toward fireplace.

3.Allow of the bottom gasketing of the glass assembly to touch the face of the fireplace.

4.Put pressure on the glass as you allow the glass assembly to drop into the two lower glass clips. See Figure 14.3.

5.Tilt top of glass towards fireplace and engage both top spring latches

UPPER SPRING LATCH

LOWER GLASS CLIP

G. Install the Mesh

The mesh front is included with the Tonic front. The Martini tinted glass front does not include mesh.

1.Remove fixed glass assembly as instructed.

2.Place glass assembly into mesh screen such that the four mesh clips attached to the mesh assembly snap into the four corresponding slots on the fixed glass assembly.

H. Air Shutter Setting

Air shutter settings may be adjusted by a qualified installer at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.4.

Loosen the 1/4 in. screw.

Twist shutter to adjust

Shutter may be open for longer horizontal vent runs.

Do not close the air shutter more than 1/16 in. for NG or 5/16 in. for LP.

Tighten the screw.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

Figure 14.4 Air Shutter

Air Shutter Settings

 

NG

LP

SLR

1/16 in.

5/16 in.

Figure 14.3 Fixed Glass Assembly

Heat & Glo • SLR • 2143-900Rev. B • 7/08

57

15 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician.

A. Intellifire Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor

The ignitor/module

 

are connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

b. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from

spark.

 

shorts in the wiring.

module to pilot assembly. Verify connections underneath pilot as-

 

 

sembly are tight; also verify connections are not grounding out to

 

 

metal chassis, pilot burner, pilot enclosure, mesh screen if present,

 

 

or any other metal object.

 

 

 

 

c. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

d. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5

 

 

mm) away from “I” terminal on module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal

 

 

module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked

 

 

insulator around electrode. Replace pilot if necessary.

 

 

 

2. Pilot won’t light,

a. No power or transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly.

voltage of transformer under load at spade connection on module

spark.

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

b. A shorted or loose connection in wir-

Remove and reinstall the wiring harness that plugs into module.

 

ing configuration or wiring harness.

Verify there is a tight fit. Verify pilot assembly wiring to module. Re-

 

 

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

c. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

d. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

e. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Re-

 

 

move ignitor wire “I” from module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal

 

 

module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked

 

 

insulator around electrode.

 

 

 

3. Pilot sparks, but

a. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits, inlet pressure must

 

 

not exceed 14 in. W.C.

 

 

 

 

b. Ignitor gap is incorrect.

Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm).

 

 

 

 

c. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

d. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

 

solenoid ohms readings.

age is below 2.7.

 

 

 

58

Heat & Glo • SLR • 2143-900Rev. B • 7/08

Intellifire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

a. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify

ues to spark, and main

 

connections are not grounding out to metal chassis, pilot

burner will not ignite.

 

burner, pilot enclosure or screen if present, or any other

(If the pilot continues

 

metal object.

to spark after the

 

 

b. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. Verify cor-

not occurred.)

 

 

rect pilot orifice is installed and gas inlet is set to pressure

 

 

 

 

specifications. Clean flame sensing rod with emery cloth to

 

 

remove any contaminants that may have accumulated on

 

 

flame sensing rod.

 

 

 

 

c. Module is not grounded.

Verify module is securely grounded to metal chassis of

 

 

appliance. Verify that wire harness is firmly connected to

 

 

the module.

 

 

 

 

d. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing

 

nated flame sensing rod.

rod is not cracked, damaged, or loose. Verify connection

 

 

from flame sensing rod to white sensor wire. Clean flame

 

 

sensing rod with emery cloth to remove any contaminants

 

 

that may have accumulated on flame sensing rod. Verify

 

 

continuity with a multimeter with ohms set at lowest range.

 

 

Replace pilot if any damage is detected.

 

 

 

 

e. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

switch or wall switch in ON position. If there is no spark at

 

 

“I” terminal module must be replaced. If there is a spark at

 

 

“I” terminal, module is fine.

 

 

 

Heat & Glo • SLR • 2143-900Rev. B • 7/08

59

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

1 INCH STANDOFF

K

L

S R M J

I

ØN

 

 

C

 

 

 

 

 

 

NON-COMBUSTIBLEZONE

 

 

 

 

 

(PROVIDED WITH UNIT)

 

 

 

GAS LINE

 

 

 

 

 

 

O ACCESS

 

 

 

 

E

H

T

 

 

 

 

D

 

 

 

 

 

 

 

P

 

 

 

 

F

 

 

 

 

 

 

 

U

 

 

 

 

 

 

 

 

B

 

 

G

ELECTRICAL

 

 

 

 

ACCESS

Q

 

A

 

 

 

 

 

 

 

 

 

 

LEFT VIEW

 

FRONT VIEW

 

 

RIGHT VIEW

Location

Inches

Millimeters

Location

Inches

Millimeters

 

A

48

1218

K

1

25

 

B

43

1092

L

37-3/4

959

 

C

39-1/16

993

M

15-3/4

400

 

D

13-1/4

337

N

6-5/8

168

 

E

39-5/8

1006

O

41-3/4

1060

 

F

3-9/16

90

P

2-3/16

55

 

G

6-7/8

174

Q

6

152

 

H

47-1/16

1195

R

17-1/4

438

 

I

9-5/16

237

S

18-1/4

464

 

J

16-3/4

425

T

25-7/8

657

 

 

 

 

U

9-3/4

248

 

Î Figure 16.1 Appliance Dimensions

 

 

 

 

 

 

60

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Vent Components Diagrams

13-7/8in.

9-1/2in.

 

 

(352 mm)

(241 mm)

11-5/8in.

 

 

 

 

 

 

(295 mm)

 

14 in.

 

7-1/8in.

12-1/8in.

(356 mm)

 

(308 mm)

 

(181 mm)

 

 

 

DRC-RADIUS

5-3/4in.

 

Cap Shield

(146 mm)

COOL-ADD

 

 

 

 

 

 

Cap Shield

 

 

11-7/8in.

5 in.

 

 

(302 mm)

(127 mm)

 

 

13-7/8in.

 

 

 

(352 mm)

 

 

PVK-80

DVP-BEK2

(For use with IPI and DSI appliances only.)

 

 

DVP-HPCCap Brick Extension

Figure 16.2 DVP vent components

 

 

 

Heat & Glo • SLR • 2143-900Rev. B • 7/08

61

B. Vent Components Diagrams (continued)

 

 

 

 

 

6-1/2in.

 

6-1/2in.

 

 

 

165 mm

 

 

 

 

 

 

165 mm

 

 

 

6-1/2in.

 

 

 

 

 

 

8-3/4in.

 

 

 

165 mm

 

 

 

 

9-1/4in.

 

222 mm

 

 

6 in.

 

 

 

235 mm

 

 

 

 

152 mm

 

 

6-5/8in.

 

 

 

 

 

168 mm

 

 

 

6-5/8in.

 

SLP-45- 45° Elbow

 

 

 

 

 

 

 

168 mm

 

 

 

 

 

 

 

 

 

 

9-7/8in.

 

 

 

 

 

251 mm

 

 

 

 

 

SLP9090° Elbow

 

 

Effective Height/Length

 

 

 

Pipe

inches

mm

 

Effective

 

SLP4

4

102

26 in.

Height/

 

SLP6

6

152

Length

 

SLP12

12

305

660 mm

 

 

SLP24

24

610

 

 

 

SLP36

36

914

 

 

 

SLP48

48

1219

 

 

SLP-PIPE

SLP6A

2 - 6 51 - 152

DVP-HSM-B

 

SLP12A

2 - 12

51 - 305

 

 

Extended Heat Shield

SLP-HVS

RF4-8

SLP-FS

SLP-WS

Horizontal Pipe

Roof Flashing

Ceiling Firestop

Wall Shield Firestop

Support

 

 

 

Figure 16.5 SLP Series Vent Components

62

Heat & Glo • SLR • 2143-900Rev. B • 7/08

B. Vent Components Diagrams (continued)

SLK-SNKD

SLP-CCS-BK

SLP-TVHW

PVK-80

Cathedral Ceiling

Vertical

Snorkel

Power Vent

Support Box-Black

Termination Cap

Termination Cap

 

 

 

 

SLP-TRAP2

SLP-DCF-BK

SLP-WT-BK

SL-2DVP

Horizontal

Ceiling Firestop

Wall Thimble-Black

Adapter

Termination Cap

Black

 

 

8-1/8in.

13 in.

Effective Length

 

 

(206 mm)

(330 mm)

5-1/2in.

8-3/8in.

5-3/4to8-3/8in.

 

 

 

 

146 to 213 mm

140 mm

213 mm

 

 

 

87°

 

 

 

 

15 in.

(381 mm) 10-1/2in.

267 mm

10-7/8in.

276 mm

Note: TheSLP-HRC-SSandSLP-HRC-ZC-SStermination caps are not approved for use with propane (LP) fuel.

SLP-HRC-SS

SLP-HRC-ZC-SS

HORIZONTAL TERMINATION CAP

Figure 16.6 SLP Series Vent Components

Heat & Glo • SLR • 2143-900Rev. B • 7/08

63

C. Service Parts

SLR

 

 

 

 

Service Parts Diagram

Beginning Manufacturing Date: July 2008

 

 

Ending Manufacturing Date: ______

1

2

3

Î

4

5

6

8

10

7

9

Part number list on following page.

64

Heat & Glo • SLR • 2143-900Rev. B • 7/08

C. Service Parts List

 

 

SLR

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

 

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

1

Elbow Heat Shield

 

2143-168

n

2

Sheet Rock Ledge

 

2143-147

N

3

Top Panel, Finishing Edge

 

2143-102

N

4

Non Combustible Board

 

2143-117

N

5

Base Pan

 

2143-115

N

6

Burner NG

 

2143-007

Y

Burner LP

 

2143-008

Y

 

 

7

Pilot Bracket

 

2143-123

n

8

Glass Door Assembly

 

GLA-SLR

Y

9

Junction Box

 

4013-021

Y

10

Lower Cover Panel

 

2143-103

N

 

 

 

 

 

 

12 in Pipe

 

SLP12

N

 

Black Rock

10 LB Bag

2143-850

N

 

Gasket Assembly

 

 

 

 

Contains burner neck, shutter bracket, vent, seal cap,

 

2121-080

N

 

valve plate, and air passage gaskets

 

 

 

 

Glass Latch Assembly

Qty 2 req

386-122A

Y

 

Finish Edge

Right

2143-118

N

 

Left

2143-169

 

 

 

 

 

Touch Up Paint

 

TUP-GBK-12

N

 

Wall Switch Kit

 

WSK-21

N

 

Conversion Kit NG

N/A

N

 

Conversion Kit LP

LPK-SLR

Y

 

Pilot Orifice NG

593-528

Y

 

Pilot Orifice LP

593-527

Y

 

Regulator NG

NGK-DXF

Y

 

Regulator LP

LPK-DXF

Y

Additional service part numbers appear on following page.

Heat & Glo • SLR • 2143-900Rev. B • 7/08

65

Service Parts

SLR

 

 

Valve Assembly Diagram/ Parts List

Beginning Manufacturing Date: July 2008

 

Ending Manufacturing Date: ______

1

IPI Valve Assembly

3

2

 

4

11

10

 

 

 

 

 

5

 

 

 

 

6

9

 

 

 

 

 

 

 

 

8

 

 

 

 

7

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

1

Pilot Assembly NG

 

2090-012

Y

Pilot Assembly LP

 

2090-013

Y

 

 

2

Valve Bracket

 

2118-104

N

3

Flex Ball Valve Assembly

 

302-320A

Y

4

Valve NG

 

593-500

Y

Valve LP

 

593-501

Y

 

 

5

Module

 

593-592

Y

6

Thermostat Wire Assembly

 

2118-170

Y

7

Module Wire Assembly

 

593-590A

Y

8

3 Volt Transformer

 

593-593A

Y

9

Bulkhead W/Flex Tube

 

7000-156

Y

10

Battery Pack

 

593-594A

Y

11

Orifice NG (#42C)

 

582-842

Y

Orifice LP (.057C)

 

582-057

Y

 

 

 

Jumper Wires 21 in

 

2012-206

 

66

Heat & Glo • SLR • 2143-900Rev. B • 7/08

D. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588,

6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940,

6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Printed in U.S.A. - Copyright 2008

Heat & Glo • SLR • 2143-900Rev. B • 7/08

67