Heat & Glo LifeStyle SL-950TV-IPI-D User Manual

Size:
3.46 Mb
Download

Owner’s Manual

Installation and Operation

Models:

SL-550TV-D,SL-550TV-IPI-D

SL-750TV-D,SL-750TV-IPI-D

SL-950TV-D,SL-950TV-IPI-D

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the Commonwealth of Massachusetts:

installation must be performed by a licensed plumber or gas fitter;

a CO detector shall be installed in the room where the appliance is installed.

WARNING

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

Keep children away.

CAREFULLY SUPERVISE children in same room as appliance.

Alert children and adults to hazards of high temperatures.

Do NOT operate with protective barriers open or removed.

Keep clothing, furniture, draperies and other combustibles away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. Do NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trained

professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, abrand of Hearth & Home Technologies, Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

Not for usewithsolidfuel.

(Nedoitpasentreutiliseavecuncombustiblesolide).

TypeofGas (Sorte De Gaz): Thisappliancemustbeinstalledinaccordancewithlocalcodes, ifany;ifnot,followANSIZ223.1intheUSAorCAN/CGAB149 installationcodes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum PermissibleGasSupplyfor PurposesofInputAdjustment.

 

 

 

ApprovedMinimum (De Gaz) Acceptable

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumPressure(Pression)

 

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

Minimum ManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

TotalElectricalRequirements: 000Vac,00Hz.,lessthan00Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INCANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN.INPUTBTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICESIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

- Table of Contents-

Section 1: Listing and Code Approvals

 

 

A. Appliance Certification...................................

4

 

B. Glass Specifications ......................................

4

 

C. BTU Specifications ........................................

4

 

D. High Altitude Installations ..............................

5

 

E. Non-combustibleMaterials Specification.......

5

 

F. Combustible Materials Specification..............

5

Section 2:

Getting Started

 

 

A. Design and Installation Considerations .........

6

 

B. Negative Pressure.........................................

7

 

C. Tools and Supplies Needed...........................

8

 

D. Inspect Appliance and Components..............

8

Section 3: Framing and Clearances

 

Î

A. Selecting Appliance Location.........................

9

Î

B. Constructing the Appliance Chase ..............

10

 

C. Clearances ..................................................

10

 

D. Mantel Projections........................................

11

Section 4:

Termination Locations

 

 

A. Vent Termination Minimum Clearances .......

12

Section 5: Vent Information and Diagrams

 

 

A. Vent Guidelines ...........................................

13

 

B. Vent System Configuration..........................

13

Section 6: Vent Clearances and Framing

 

 

A. Pipe Clearances to Combustibles ...............

15

 

B. Wall Penetration Framing ............................

15

 

C. Vertical Penetration Framing .......................

15

Section 7:

Appliance Preparation

 

 

A. Installing Outside Air Kit Damper Assembly..

16

 

B. Gas/Electrical Connections .........................

16

 

C. Securing and Leveling Appliance ................

17

Section 8: Installing Vent Pipe

 

 

A. Assembly of Vent Sections..........................

18

 

B. Attaching Vent to Firebox ............................

18

 

C. Securing Vent Sections ..............................

18

Section 9:

Gas Information

 

 

A. Fuel Conversions.........................................

19

 

B. Gas Pressures.............................................

19

 

C. Gas Connection...........................................

19

Section 10:

Electrical Information

 

 

A. Recommendation for Wire ........................

21

 

B. Connecting to the Appliance .....................

21

 

C. Intellifire Ignition System Wiring................

21

 

D. Standing Pilot Ignition System Wiring.......

22

 

E. Junction Box Installation ...........................

23

 

F.

Wall Switch Installation for Fan.................

23

Section 11:

Finishing

 

 

A. Mantel Projections ....................................

24

 

B.

Facing Material .........................................

24

Section 12:

Appliance Setup

 

 

A. Remove Shipping Materials......................

25

 

B. Remove Grate Shipping Support..............

25

 

C. Clean the appliance ..................................

25

 

D. Accessories ..............................................

25

 

E. Install the Refractory.................................

25

 

F. Lava Rock, Vermiculite, Rockwool

 

 

 

and Ember Placement ..............................

25

 

G. Positioning the Logs .................................

26

 

H. Glass Assembly ........................................

30

 

I.

Screen Mesh.............................................

30

 

J.

Grilles and Trim.........................................

30

 

K. Hood .........................................................

30

 

L. Shutter Settings ........................................

30

Section 13:

Operating Instructions

 

 

A. Before Lighting Appliance .........................

31

 

B. Check Appliance Draft ..............................

31

 

B. Lighting Appliance.....................................

32

 

C. After Appliance is Lit .................................

34

 

D. Frequently Asked Questions.....................

34

Section 14:

Troubleshooting

 

 

A. Standing Pilot Ignition System ..................

35

 

B. Intellifire Ignition System...........................

37

Section 15:

Maintaining and Servicing Appliance...........

39

Section 16:

Reference Materials

 

 

A. Appliance Dimension Diagram .................

41

 

B. Service Parts ............................................

42

 

C. Warranty ...................................................

52

 

D. Contact Information ..................................

53

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

3

1Listing and Code Approvals

A. Appliance Certification

MODELS: SL-550TV-D,SL-750TV-D,SL-950TV-D,

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: B-VentDecorative

STANDARD: ANSIZ21.50-2002• CGA2.2

This product is listed to ANSI standards for “Vented Gas Fireplaces” and “Gas Fired Appliances for Use at High Altitudes”.

This model (natural gas and propane) can be installed in a bedroom (in the United States) which has a total volume of unconfined space appropriate to the particular installation. Refer to the National Fuel Gas Code ANSI Z223.1/

NFPA54 (current edition), The Uniform Mechanical Code - (current edition), and local Building Officials for the options allowed in obtaining an effective bedroom volume of unconfined space.

This model (natural gas and propane) can be installed in a bedroom (in Canada) if a thermostat (Model WH-STAT)is installed with the unit. Consult local code authorities. Detailed installation instructions for ModelWH-STATare included with the kit.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

Heat & Glo Quality Systems registered by SGS ICS

B. Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with theNational Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and theCAN/CGA B149 Installation Codes in Canada.

C. BTU Specifications

Model(s)

 

Maximum

Minimum

Orifice

 

Input BTU/h

Input BTU/h

Size

U.S. (0-2000ft.) or Canada(2000-4500ft.)

(DMS)

SL-550TV-D

US

21,000

12,000

44

 

 

 

 

SL-550TV-IPI-D

CAN

18,900

10,800

45

 

 

 

 

 

 

SL-550TV-D(LP)

US

20,000

N/A

54

 

 

 

 

SL-550TV-IPI-D(LP)

CAN

18,000

N/A

55

 

 

 

 

 

 

SL-750TV-D

US

23,000

16,000

42

 

 

 

 

SL-750TV-IPI-D

CAN

20,700

14,400

43

 

 

 

 

 

 

SL-750TV-D(LP)

US

23,000

N/A

53

 

 

 

 

SL-750TV-IPI-D(LP)

CAN

20,700

N/A

54

 

 

 

 

 

 

SL-950TV-D

US

30,000

21,000

36

 

 

 

 

SL-950TV-IPI-D

CAN

27,000

18,900

37

 

 

 

 

 

 

SL-950TV-D(LP)

US

30,000

21,000

51

 

 

 

 

SL-950TV-IPI-D(LP)

CAN

27,000

N/A

52

 

 

 

 

 

 

4

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

D. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750oC,shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

5

2 Getting Started

A. Design and Installation Considerations

Heat & Glo B-typevent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

Where the appliance is to be installed. See Sections 3 and 4.

The vent system configuration to be used. See Sections

5 and 6.

Gas supply piping. See Sections 7 and 9.

Electrical wiring. See Sections 7 and 10.

Framing and finishing details. See Sections 3, 6 and 11.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.See Section 10.

WARNING

Fire Risk

Explosion Risk

Keep appliance dry.

Water may damage controls.

Mold or rust may cause odors.

6

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

B. Negative Pressure

WARNING

Asphyxiation Risk.

Negative pressure can cause spillage of combustion fumes and soot.

Fireplace needs to draft properly for safety.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

Preventing negative pressure

Location of fireplace and chimney

Negative pressure results from the imbalance of air available for the fireplace to operate properly. Causes for this imbalance include:

Exhaust fans (kitchen, bath, etc.)

Range hoods

Combustion air requirements for furnaces, water heaters and other combustion appliances

Clothes dryers

Location of return-airto furnace or air conditioning

Imbalances of the HVAC air handling system

Upper level air leaks (recessed lighting, attic hatch opening, duct leaks)

To minimize the effects of negative air pressure, the following must be considered:

Install the fresh air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace.

Avoid installing the fireplace near doors, walkways or small isolated spaces.

Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted ductwork and air handler joints and seams taped or sealed.

Basement installations should be avoided due to stack effect. Stack effect creates negative pressure in lower levels. Hearth & Home Technologies recommends the use of direct vent fireplaces in basements.

Location of the fireplace and chimney will affect performance. As shown in Figure 2.1, the chimney should:

Be installed through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-downof the fire.

Penetrate the highest part of the roof. This minimizes the effects of wind turbulence.

Be located away from trees, adjacent structures, uneven roof lines and other obstructions.

Offsets can restrict draft so their use should be minimized. Consider the fireplace location relative to floor and ceiling and attic joists.

Recommended Recommended

Location Location

Marginal

Location

Location

Not

Recommended

Location NOT

Recommended

Leeward

Multi-levelRoofs

Figure 2.1

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

7

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw

Framing material

Pliers

Hi temp caulking material

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Tape measure

Manometer

Voltmeter

Non-corrosiveleak check solution

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews One 1/4 inch female connection (for optional fan).

D. Inspect Appliance and Components

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components.

Report suspected damaged parts to dealer.

The following B-ventcomponents are needed for installation (see Figure 2.2).

Fireplace Box

Pipe Components

Firestops

Attic Insulation Shield

Elbows

Strapping

Roof Flashing or Chase Top

Termination Cap

Storm Collar

Carefully remove the appliance and components from the packaging.

The vent system components and trim doors are shipped in separate packages.

The gas logs may be packaged separately and must be field installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

VERTICAL TERMINATION CAP

STORM COLLAR

ROOF FLASHING

OR CHASE TOP

ATTIC INSULATION SHIELD

FIRESTOP SPACER

GAS B-VENT

PIPE SECTION (S)

Figure 2.2 Typical Vertical Installation

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

8

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

3 Framing and Clearances

NOTE:

 

WARNING

Illustrations reflect typical installations and are FOR

 

 

DESIGN PURPOSES ONLY.

Fire Risk

Illustrations/diagrams are not drawn to scale.

Provide adequate clearance:

Actual installation may vary due to individual design

Around air openings

 

preference.

 

To combustibles

 

 

 

 

For service access

A. Selecting Appliance Location

Locate appliance away from traffic areas.

 

 

When selecting a location for your appliance it is important to

consider the required clearances to walls (see Figure 3.1). NOTE: For actual appliance dimensions refer to

Section 16.

A

F

TOP VENT

B

ALCOVE

INSTALLATION D

A

B

C

TOP VENT

TOP VENT

B

E

Model

A

B

C

D

E

F

 

 

 

 

 

 

 

 

SL-550TV-D

Inches

41-1/2

37

58-3/4

 

16-1/4

1/2

 

 

 

 

 

 

 

Millimeters

1054

940

1492

 

413

13

 

 

 

 

 

 

 

36 Inches

 

 

 

Inches

45

42

63-3/4

16-1/4

1/2

SL-750TV-D

914 Millimeters

 

 

 

 

 

 

Millimeters

1143

1067

1619

Maximum

413

13

 

 

 

 

 

 

 

 

 

 

 

SL-950TV-D

Inches

50

49

70-3/4

 

16-1/4

1/2

 

 

 

 

 

 

 

Millimeters

1270

1245

1792

 

413

13

 

 

 

 

 

 

 

 

 

 

In addition to these framing dimensions, also reference the following sections:

Clearances and Mantel Projections (Sections 3.C and 3.D)

Vent Clearances and Framing (Section 6).

ÎFigure 3.1 Appliance Locations

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

9

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase.

Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts in cold climates, the firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

WARNING

Fire Risk.

Odor Risk.

Install appliance on hard metal or wood surfaces extending full width and depth of appliance.

Do NOT install appliance directly on carpeting, vinyl, tile or any combustible material other than wood.

Do NOT place furniture or any other combustible household objects within 36 inches of the appliance front.

WARNING

Fire Risk.

Construct chase to all clearance specifications in manual.

Locate and install appliance to all clearance

specifications in manual

A

E

 

 

 

 

 

F

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

 

 

I

 

 

 

 

 

 

 

 

 

 

 

Models

A

B

C

D

E

F

G

H

I

J

SL-550TV-D

Inches

10

33

16-1/4

37

31

0

0

1/2

1/2

36

mm

254

838

413

940

787

0

0

13

13

914

 

SL-750TV-D

Inches

10

38-1/4

16-1/4

42

31

0

0

1/2

1/2

36

mm

254

971

413

1067

787

0

0

13

13

914

 

SL-950TV-D

Inches

10

42-1/4

16-1/4

49

31

0

0

1/2

1/2

36

mm

254

1073

413

1245

787

0

0

13

13

914

 

Î Figure 3.2 Clearances to Combustibles

 

 

 

 

 

 

 

 

 

 

10

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

D. Mantel Projections

 

12 INCHES

 

(305mm)

NON-COMBUSTIBLE

12 INCHES

MATERIAL ONLY

(305mm)

 

 

1/2 INCH

 

(13mm)

TOP FRONT EDGE

OF FIREPLACE

Figure 3.3 Clearances to Mantels or other

Combustibles above Appliance

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

11

4 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

8 FEET

VERTICAL

 

WALL

LOWEST

DISCHARGE

OPENING

TERMINATION

CAP

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5*

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 4.1 Minimum Height from Roof to Lowest Discharge Opening

Figure 4.1 specifies minimum vent heights for various pitched roofs.

 

 

 

 

GAS OR WOOD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TERMINATION

 

 

8 FEET

 

 

 

 

 

 

 

 

 

 

 

(MINIMUM) TO

 

 

 

 

 

 

 

 

 

 

 

PERPENDICULAR

 

 

 

 

 

GAS

 

 

 

WALL (GAS ONLY)

18 IN. TERMINATION

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Termination Clearances

 

Gas

Wood

A

6 inches

20 inches

Figure 4.2 Multiple Vertical Termination

12

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

5 Vent Information and Diagrams

A. Vent Guidelines

 

Rise to Run Ratio = 2:1

WARNING

 

Maximum Total Horizontal Run = 15 Feet

 

Minimum Total Vertical Rise = 9 Feet

Fire Risk.

 

Maximum Total Vertical Rise = 30 Feet

 

Maximum Number of Elbows: Two 900 or Four 450

Asphyxiation Risk.

 

 

 

This appliance requires the specified pipe for

 

operation.

 

 

• Incorrect pipe may cause spillage, condensation

MINIMUM CLEARANCES

and overheating.

 

 

ARE PER VENT

 

 

MANUFACTURER’S

These models require the following size B-ventdouble

SPECIFICATIONS

 

wall, or single wall rigid or flex vent pipe.

 

 

Models

Pipe Size

9 FEET

SL-550TV-D,SL-550TV-IPI-D

5 inches

MINIMUM

SL-750TV-D,SL-750TV-IPI-D

5 inches

 

SL-950TV-D,SL-950TV-IPI-D

6 inches

 

B-ventpipeMUST be used when the vent system is

VENT SUPPORTS ARE PER

within combustible construction.

 

VENT MANUFACTURER’S

 

 

SPECIFICATIONS

Single wall rigid or flexible vent may be used ONLY if the vent system is installed withinnon-combustibleconstruction such as a masonry chimney.

Follow pipe manufacturer’s installation guidelines when installing the appliance.

Figure 5.1

WARNING

 

Fire Hazard.

 

 

 

Explosion Risk.

 

 

 

Asphyxiation Risk.

 

 

 

Do NOT connect this gas appliance to a

 

 

 

chimney flue serving a separate solid-fuelor

VENT SUPPORTS

 

 

gas burning appliance.

 

 

ARE PER VENT

 

 

• Vent this appliance directly outside.

MANUFACTURER'S

METAL

 

• Use separate vent system for this appliance.

SPECIFICATIONS.

PLUMBERS' STRAP

 

 

 

 

May impair safe operation of this appliance or

 

 

 

other appliances connected to the flue.

 

 

B. Vent System Configuration

MAXIMUM HORIZONTAL RUN IS 50%

 

 

OF VERTICAL. HORIZONTAL RUN

 

CAUTION

CANNOT BE MORE THAN 15 FT.

 

 

 

ALL vent configuration specifications MUST be followed.

 

 

This product is tested and listed to appliance and vent

 

 

 

manufacturer’s specifications.

 

 

• Appliance performance will suffer if specifications are not

 

 

 

followed.

Figure 5.2

 

 

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

13

WARNING

Fire Risk. Explosion Risk.

Insulation and other combustibles must not infringe on clearances.

• ALWAYS maintain specified clearances around venting and firestop systems.

• Install firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

MAXIMUM HORIZONTAL 15 FEET

MINIMUM VERTICAL 9 FEET

45 DEGREES

OFFSETS EXCEEDING

ELBOW

45 DEGREES ADAPT

 

HORIZONTAL LIMITATIONS

90 DEGREES

 

ELBOW

 

Note: Maximum horizontal distance is 50% vertical vent height.

Figure 5.3

14

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

6 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

• Do not pack air space with insulation or other materials.

National building codes recommend using attic shield to keep loose materials/insulation from contacting vent.

Failure to keep insulation or other materials away from vent pipe may cause fire.

TOP

CLEARANCE

CLEARANCE

AROUND VERTICAL

SECTIONS

SIDE AND

BOTTOM CLEARANCE

C. Vertical Penetration Framing

Use B-ventmanufacturer’s firestops to provide adequate clearances.

WARNING

Fire Hazard

Keep loose materials or blown insulation from touching the vent pipe.

National building codes recommend using attic shield to keep loose materials/ blown insulation from contacting vent.

Hearth & Home Technologies requires the use of an attic shield.

Figure 6.1 Pipe Clearances

Follow vent pipe manufacturer’s instructions for all clearances around pipe.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

15

7 Appliance Preparation

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

A. Installing Outside Air Kit Damper Assembly

 

WARNING

 

 

 

Asphyxiation Risk.

 

Figure 7.2 Outside Air Kit Installation

 

 

 

 

Fire Risk.

• Attach damper assembly to appliance using screws

 

Do NOT draw outside combustion air from:

 

• Wall, floor or ceiling cavity.

 

provided (see Figure 7.2).

 

• Enclosed space such as an attic or garage.

Insert narrow end of handle through tab and into upper

 

• Close proximity to exhaust vents or chimneys.

 

slot of door.

 

Fumes or odor may result.

Check handle operation. Pull handle out to open, and in

 

 

 

 

 

to close.

Remove and discard cover plate or knockout from side

B. Gas and Electrical Connections

 

of appliance.

Open air kit damper slightly.

If applicable, ensure that gas and electrical connections are

• Locate door hinge toward back of appliance (see Figure

installed at this time. Refer to Sections 9 (Gas Information)

 

7.1).

and 10 (Electrical Information).

DOOR

HINGE

HANDLE

Figure 7.1 Damper Assembly and Handle

16

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

C. Securing and Leveling Appliance

WARNING

Fire Risk.

Prevent contact with sagging, loose insulation.

Do NOT install against combustible materials

such as exposed insulation, plastic and insulation backer.

The diagram shows how to properly position, level, and secure the appliance (see Figure 7.3). Nailing tabs are provided to secure the appliance to the framing members.

Place the appliance into position.

Level the appliance from side to side and front to back.

Shim the appliance, as necessary. It is acceptable to use wood shims.

Bend out nailing tabs on each side.

Keep nailing tabs flush with the framing.

Secure the appliance to the framing by using nails or screws through the nailing tabs.

Figure 7.3 Proper Positioning, Leveling and Securing of a

Appliance

CAUTION

Do NOT notch into the framing around the appliance spacers.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

17

8 Installing Vent Pipe

A. Assembly of Vent Sections

This B-Ventappliance requires5-inch(SL-550/750TV-D)or6-inch(SL-950TV-D)B-ventdouble-wallpipe. Follow the pipe manufacturer’s installation guidelines when installing the unit. This will ensure proper operation and prevent safety hazards.

WARNING

Fire Risk

Exhaust Fumes Risk

Impaired Performance of Appliance

• Assemble pipe sections per B-ventmanufacturer’s instructions.

Use support tabs for screws.

Screws must not exceed one inch long and must not penetrate inner lining.

Pipe may separate if not properly joined.

C. Securing Vent Sections

Secure vent sections with vent supports following B-ventmanufacturer’s instructions.

WARNING

Fire Risk. Explosion Risk.

Combustion Fume Risk.

Use vent run supports per vent manufacturer’s installation instructions.

Connect vent sections per vent manufacturer’s installation instructions.

Maintain all clearances to combustibles.

Maintain specified slope (if required).

Improper support may allow vent to sag or separate.

B. Attaching Vent to Firebox

Attach the first B-Ventcomponent to the flue outlet collar using 3self-tappingscrews. See Figure 8.1.

B-VENT

 

SECURING

 

SCREWS

 

FLUE OUTLET

 

COLLAR

 

Figure 8.1

 

18

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

9 Gas Information

A. Fuel Conversions

C. Gas Connection

Before making gas connections ensure that appliance being installed is compatible with the available gas type.

Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts.

NOTE: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.)

B. Gas Pressures

Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA51.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressure must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum Inlet

5.0 inches

11.0 inches

Pressure

w.c.

w.c.

Maximum Inlet

14.0 inches

14.0 inches

Gas Pressure

w.c.

w.c.

Manifold Pressure

3.5 inches

10.0 inches

w.c.

w.c.

 

NOTE: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Refer to Reference Section 16 for location of gas line access in appliance.

NOTE: Gas line may be run from either side of the appliance provided the hole in the outer wrap does NOT exceed2-1/2inches in diameter and does not penetrate the firebox.

WARNING

Gas Leak Risk

Support control when attaching pipe to prevent bending gas line.

NOTE: The gap between the supply piping and gas access hole may be caulked with high temperature caulk or stuffed withnon-combustible,un-facedinsulation to prevent cold air infiltration.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

19

Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes.

Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.

WARNING

Fire or Explosion Hazard

• Gas build-upduring line purge may ignite.

• Purge should be performed by qualified technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING

CHECK FOR GAS LEAKS

Explosion Risk

Fire Risk

Asphyxiation Risk

Check all fittings and connections.

Do not use open flame.

After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially-available,noncorrosive leak check solution. Be sure to rinse off all leak check solution following testing.

Fittings and connections may have loosened during shipping and handling.

WARNING

Fire hazard.

Explosion Risk.

Do NOT change the valve settings.

This valve has been preset at the factory.

Changing valve settings may result in fire hazard or bodily injury.

HIGH ALTITUDE INSTALLATIONS

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

20

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

10 Electrical Information

A. Recommendation for Wire

This appliance requires 110-120VAC be wired to the junction box either for use of optional accessories (standing pilot ignition) or for proper operation of the appliance (Intellifire ignition). Refer to Figure 10.1 to determine if the appliance uses an Intellifire ignition system or Standing Pilot ignition system.

Open the control access panel to view wiring system and gas valve. If this appliance has a red or black ignitor button (as noted in Figure 10.1) this appliance has a Standing Pilot ignition system. If there is no red or black ignitor button, this appliance has an Intellifire ignition system.

Figure 10.1

Standing Pilot Ignition

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

B. Connecting to the Appliance

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

This appliance MUST be used with a wall switch or a remote control.

If using thermostat use one compatible with a millivolt gas valve system.

Follow parameters for locating thermostat (see individual thermostat instructions) to ensure proper operation of appliance.

Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.

Keep wire lengths short as possible by removing any excess wire length.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

C.Intellifire Ignition System Wiring

This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.2.

This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

This appliance is supplied with a battery pack and a 3 volt AC transformer, which requires the installation of the supplied junction box. It is highly recommended that the junction box be installed at this time to avoid reconstruction.

The battery pack requires two D cell batteries (not included).

NOTE: Batteries cannot be placed in the battery pack while using the 3 volt AC transformer. The transformer must be unplugged if the battery pack is used or battery life will be reduced.

CAUTION

Battery polarity must be correct or module damage will occur.

Optional Accessories Requirements

Wiring for optional accessories should be done now to avoid reconstruction.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING

Shock hazard.

Replace damaged wire with type 105º C rated wire.

Wire must have high temperature insulation.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

21

INTERMITTENT

PILOT IGNITOR

I

IGNITION

MODULE 3 VAC

S

TRANSFORMER 3V

 

 

WHITE

 

 

 

 

ORG

 

 

 

 

GROUND TO

 

PLUG-IN

 

BROWN

FIREPLACE CHASSIS

BLACK

 

 

 

BROWN

 

 

GREEN

RED

 

ORG

 

 

 

 

BATTERY PACK

TEMP SENSOR

VALVE

THERMOSTAT WIRE ASSEMBLY

Figure 10.2 Intellifire Pilot Ignition (IPI) Wiring Diagram

TRANSFORMER

3 VAC

PLUG-IN

INTERMITTENT

PILOT IGNITOR

REMOTE RECEIVER

IGNITION MODULE 3 VAC

 

WHITE

 

ORG

BLACK

GROUND TO

FIREPLACE CHASSIS

 

RED

 

TEMP SENSOR

JUMPER WIRE TO BROWN

ORG

GREEN

BATTERY PACK

 

 

 

VALVE

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on

3 volts. 120 VAC is required at junction box unless equipped with battery back-up.

D. Standing Pilot Ignition System Wiring

This standing pilot ignition system wiring does not require a 110 VAC supply to operate.

It is recommended that a 110 VAC junction box be installed for use with a fan or remote control. (See Figure 10.4 for junction box wiring).

WHITE

PILOT

PIEZO

PILOT

THERMOCOUPLE

 

THERMOCOUPLE

RED

TEMP SENSOR

VALVE

 

 

VALVE

THERMOSTAT WIRE ASSEMBLY

WHITE

RED

TEMP SENSOR

REMOTE

RECEIVER

Figure 10.3 Standing Pilot Ignition Wiring Diagram

22

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

E. Junction Box Installation

If the box is being wired from the OUTSIDE of the appliance:

Remove the cover plate located on the outer shell right side (see Figure 10.4).

Install the supplied Romexconnector in the cover plate.

Feed the necessary length of wire through the connector.

Make all necessary wire connections and reattach the cover plate to the outer shell.

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box/receptacle inward to disengage it from the outer shell (see Figure 10.4).

Pull the electrical wires from outside the appliance through this opening into the valve compartment.

Feed the necessary length of wire through the connector.

Make all necessary wire connections to the junction box/receptacle and reassemble the junction box/ receptacle to the outer shell.

 

Romex

 

Connector

 

14/2WG

 

Cover Plate

 

outside firebox

WHT

 

BLK

 

WHT

 

BLK

Copper

 

GRN wire

ground attached

to GRN screw with

inside box

GRN wire

 

NOTE: Do NOT wire

Figure 10.4 Junction Box Detail

110VAC to wall switch.

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 10.5):

The power supply for the appliance must be brought into a switch box.

The power can then be supplied from the switch box to the appliance using a minimum of 14-3with ground wire.

At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

Add a 1/4 inch insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 inch male) as shown.

Heat & Glo

 

 

 

SWITCH

MINIMUM 14-3AWG

 

 

 

WITH GROUND

 

 

 

 

 

Red

Black

 

 

Black

 

 

White

White

 

 

Green

Green

JUNCTION BOX

 

Green

 

Red

Black White

 

 

 

 

POWER

 

 

 

SUPPLY WIRES

 

 

 

SWITCH BOX

Red

 

 

 

Figure 10.5 Fan Control Switch Wiring

 

 

SL-550 /750 /950TV-D2053-985Rev. J • 4/07

23

11Finishing

A. Mantel Projections

Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance.

 

12 INCHES

 

(305mm)

NON-COMBUSTIBLE

12 INCHES

MATERIAL ONLY

(305mm)

 

 

1/2 INCH

 

(13mm)

 

TOP FRONT EDGE

 

OF FIREPLACE

Figure 11.1 Clearances to Mantels or other

Combustibles above Appliance

B. Facing Material

WARNING

Fire Risk.

Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles.

Modifying or covering grilles could cause temperature rise and fire hazard.

Finishing materials must not interfere with:

Air flow through grilles or louvers.

Operation of louvers or doors.

Access for service.

FINISH WALL MATERIAL

MAY BE COMBUSTIBLE

- TOP AND SIDES

TOP SEAL

JOINT

SIDE SEAL

JOINT

1/2 INCH

(13mm)

1/2 INCH

(13mm)

Figure 11.3 Noncombustible Facing Diagram

WARNING

Fire Risk.

Finish all edges and fronts to clearances and specifications listed in manual.

Black metal appliance front may be covered with noncombustible material only.

Do NOT overlap combustible materials onto appliance front.

Install combustible materials up to specified clearances on top front and side edges.

Seal joints between the finished wall and appliance top and sides using only a 300º F minimum sealant.

24

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

12 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

B. Remove Grate Shipping Support

Remove the log pack and hood, if applicable.

Bend top retaining tab of grate shipping support into vertical position (see Figure 12.1).

Lift grate slightly upward with one hand so that the grate clears the support.

Slide shipping support to side, remove and discard.

Lower grate onto refractory.

Figure 12.1

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 16.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listedaccessories voids warranty.

Using non-listedaccessories may result in a safety hazard.

Only Hearth & Home Technologies approved accessories may be used safely.

E.Install the Refractory

F.Lava Rock, Vermiculite, Rockwool/ Ember Placement

WARNING

Explosion Risk.

Follow ember placement instructions in manual.

Do NOT place embers directly over burner ports.

Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place thedime-sizeember pieces about 1/2 inch apart near port holes in burner top, but not on or in between the ports. For best performance do NOT place embers on ports at rear of burner (see Figure 12.2). Failure to follow this procedure will likely cause lighting and sooting problems.

Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

Figure 12.2 Placement of Embers

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

25

G. Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

Log Set Assembly: LOGS-SL550-DModels:SL-550TV-D

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

 

2

 

4

 

TABS

 

 

 

 

 

 

 

 

 

1

 

3

5

 

 

 

 

 

 

 

 

 

 

 

 

METAL TABS

NOTCHES

1

LOG #1 (SRV2044-700): Place log #1 onto the grate bars so that the notches in the bottom of the log fit onto the grate bars. Slide the log to the front tab for NG, slide to the rear tab for LP.

NOTCH

2

LOG #2 (SRV550-717): Place log #2 on the right two grate bars using the notch on the bottom of log #2. Slide the right edge of log #2 forward until it touches the grate.

26

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

NOTCH

3

LOG #3 (SRV2044-703): Place log #3 on the left two grate bars using the notch on the bottom of log #3. Slide the left edge of log #3 forward until it touches the grate.

4

TAB LOCATOR

LOG #4 (SRV2044-701): Place log #4 into the tab on log #1. The bottom notch of log #4 should sit on the grate as shown.

 

 

5

TAB LOCATOR

 

 

 

 

 

 

LOG #5 (SRV2044-702): Place log #5 into the tab in log #1. The “Y” end of log #6 should fit around the grate as shown.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

27

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

2 4 6

1

3 5

Log Set Assembly: LOGS-SL750-D

Models: SL-750TV-D,SL-950TV-D

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

METAL TABS

1

NOTCHES

LOG #1 (SRV2045-700): Place log #1 on the grate using the notches in the bottom of the log. Slide log #1 up to the front tabs for NG. Slide it back until top of log touches the back of the fireplace for LP.

2

NOTCHES

LOG #2 (SRV530-719): Place log #2 on the right two grate bars using the notches in the bottom of the log. Slide the log backward until the back edge is in contact with the tab and parallel to log #1.

28

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

RAISED FLAT SPOTS

3

NOTCHES

RAISED FLAT SPOTS

LOG #3 (SRV530-718): Place log #3 on the left two grate bars using the notches in the bottom of the log. Position log parallel to log #1 and on the same line as log #2. Left edge of log should rest between grate bar and second tab.

4

TAB LOCATOR

LOG #4 (SRV2045-703): Place log #4 on top of log #1 and log #2 so that the cutouts on the bottom of log #4 fit on the tab on log #1 and will fit in the flat spot on log #2.

5

TAB LOCATOR

LOG #5 (SRV2045-702): Place log #5 on the tab on log #1 so that the cutouts on the bottom of log #5 fit onto the raised flat spots on log #2.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

29

6

TAB LOCATOR

LOG #6 (SRV2045-701): Place log #6 so that the right edge fits into the notch on log #5, the middle goes into the tab on log #1, and the left edge rests on log #3.

H. Glass Assembly

WARNING

Handle glass doors with care.

Inspect the gasket to ensure it is undamaged.

Inspect the glass for cracks, chips or scratches.

Any scratch in glass, requires replacement.

Do NOT strike, slam or scratch glass.

Do NOT operate appliance with glass door removed, cracked, broken or scratched.

Replace glass door assembly as a complete appliance.

Removing Glass Assembly

Pull the four glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance (see Figure 12.17).

Replacing Glass Assembly

Replace the glass door on the appliance. Pull out and latch the four glass assembly latches into the groove on the glass frame.

LATCHES

(BOTH BOTTOM

AND TOP)

I. Screen Mesh

The screen mesh is a protective barrier and must be attached.

J. Grilles and Trim

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other non-combustiblematerials can be used to cover up the gap between the sheet rock and the appliance.

Do not obstruct or modify the air inlet/outlet grilles or hood. When overlapping on both sides, leave enough space so that the bottom grille can be lowered and the trim door removed.

K. Hood

Hood is included with the front and required in all installations.

L. Shutter Settings

Models

NG

LP

SL-550TV-D

1/4 in.

3/8 in.

SL-750TV-D

1/4 in.

3/8 in.

SL-950TV-D

3/8 in.

Full open

GLASS

ASSEMBLY

Figure 12.17 Glass Assembly

30

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

13 Operating Instructions

A. Before Lighting Appliance

Before lighting this appliance determine if it has a Standing Pilot or Intellifire ignition system by opening the control access panel to view wiring system and gas valve. If this appliance has a red or black ignitor button (see Figure 10.1) this appliance has a Standing Pilot ignition system. If there is no red or black ignitor button, this appliance has an Intellifire ignition system.

CAUTION

If installing Intellifire ignition battery backup:

Do not install batteries if the backup mode may not be used for extended time.

Batteries may leak.

Install batteries only when needed for power outage.

Before operating this appliance have a qualified technician:

Remove all shipping materials from inside and/or underneath the firebox.

WARNING

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

• Keep children away.

• CAREFULLY SUPERVISE children in same room as appliance.

Alert children and adults to hazards of high temperatures.

Do NOT operate with protective barriers open or removed.

Keep clothing, furniture, draperies and other combustibles away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. Do NOT operate the appliance with the protective barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

Review proper placement of logs, rockwool, lava rock, and vermiculite.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

Ensure that the flow of combustion and ventilation air is

B. Check Appliance Draft

 

 

not obstructed (front grilles and vent caps).

Check draft of appliance to

 

 

 

 

DRAFT HOOD

 

 

 

verify proper venting condi-

 

 

WARNING

 

 

 

tions.

 

 

Glass door must be in place when

• Close all windows and

 

 

doors, turn on all exhaust

 

 

appliance is operating. Risk of:

 

 

fans in home.

FLAME UP

 

Combustion Fumes

 

• Appliance is to be com-

- ACCEPTABLE -

 

Fire

 

 

Do NOT operate appliance with glass door removed.

pletely assembled to nor-

 

 

• Open viewing glass for servicing only.

mal operating condition.

 

 

• Turn on appliance and al-

 

 

• Glass door MUST be in place and sealed before operating

 

 

appliance.

 

low to operate for at least

 

 

• Only use glass door certified for use with appliance.

10 minutes.

 

 

• Glass replacement should be done by qualified

• Check draft as shown in

FLAME IN

 

- GOOD -

 

technician.

 

Figure 13.1. This can be

 

 

 

 

 

 

done using a smoke or

 

 

 

WARNING

flame producing match.

 

 

 

• Hold lit match at bottom

 

 

Do NOT use this appliance if any part has been under water.

edge of draft hood opening

 

 

and observe flame/smoke

 

 

Immediately call a qualified service technician to inspect the

 

 

per the figure.

FLAME OUT

 

appliance and to replace any part of the control system and

 

 

- BAD -

 

any gas control which has been under water.

Figure

13.1

 

 

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

31

C. Lighting Appliance

Intellifire Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. Do not try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

CAUTION:

Hot while in operation. Do not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

Final Inspection by _____________________________

LIGHTING

INSTRUCTIONS (IPI)

1.Turn off all electric power to the appliance.

2.This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand.

GAS

VALVE

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you don’t smell gas, go to next step.

4.Turn on all electric power to the appliance.

5.To light the burner, flip the ON/OFF switch to the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6.If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Turn off all electric power to the appliance if service is to be performed.

2.Flip ON/OFF switch to the “OFF” position.

593-913D

32

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

Standing Pilot Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

CAUTION:

Hot while in operation. Do not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS

1.Turn off all electric power to the appliance.

2.Push in gas control knob slightly and turn clockwise

to “OFF”.

NOTE: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you don’t smell gas, go to next step.

4.Find the pilot. The pilot is inside combustion chamber next to the main burner.

5.Turn knob on gas control counter clockwise

to “PILOT”.

6.Push in control knob all the way and hold in. Immediately depress red or black piezo button. It may require several depressions of the red or black piezo button until PILOT lights. If PILOT light does not light after 10 seconds, return to step 3. Continue to hold the control knob in for about one minute after the pilot is lit. Release knob and it will pop back out. Pilot should remain lit. If it goes out, repeat steps 3 through 6.

If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

7.Turn gas control knob counterclockwise to

“ON”.

8.To light Burner, flip the on/off switch to the “ON” position, and close access grille.

9.Turn on all electric power to the appliance.

 

 

 

TO TURN OFF

 

 

 

 

GAS TO APPLIANCE

1.

Turn off all electric power to the appliance if service

 

 

is to be performed.

2.

Open control access panel.

3.

Move switch to “OFF” position.

4.

Push in gas control knob slightly and turn clock-

 

 

wise

to OFF”. Do not force.

5.

Close control access panel.

 

 

 

 

464-903G

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

33

D. After Appliance is Lit

Initial Break-inProcedure

When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

NOTE: The appliance should be run three to four hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours. This will help to cure the products used in the paint and logs.

During this break-inperiod it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

CAUTION

Smoke and odors released during initial operation.

Open windows for air circulation.

Leave room during initial operation.

Smoke may set off smoke detectors.

Smoke and odors may be irritating to sensitive individuals.

WARNING

Fire Risk.

High Temperatures.

Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air.

Do NOT place combustible items on top of or in front of appliance.

Keep furniture, draperies away from appliance.

WARNING

Fire Hazard.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

Do NOT store flammable materials in the appliance’s vicinity.

Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids in this appliance.

Combustible materials may ignite.

E. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance

warms, this condensation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appli-

ance is allowed to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this appliance may release an odor for the first several hours.

Odor from appliance

This is caused by the curing of the paint and the burning off of any oils remaining

from manufacturing. Odor may also be released from finishing materials and adhe-

 

 

sives used around the appliance.

 

 

 

This is a normal result of the curing process of the paint and logs. Glass should be

Film on the glass

cleaned within 3 to 4 hours of initial burning to remove deposits left by oils from the

manufacturing process. A non-abrasivecleaner such as gas fireplace glass cleaner

 

 

may be necessary. See your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down,

Metallic noise

similar to the sound produced by a furnace or heating duct. This noise does not af-

 

fect the operation or longevity of the appliance.

 

 

Is it normal to see the pilot flame

In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off

burn continually?

when ON/OFF is turned off. In a standing pilot system the pilot will always stay on.

 

 

34

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

14 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

A. Standing Pilot Ignition System

Symptom

Possible Causes

Corrective Actions

 

 

 

1. After repeated

a. Defective ignitor.

Check the spark at the electrode and pilot. If no spark and electrode wire

triggering of the

 

is properly connected, replace the ignitor.

red or black piezo

 

 

ignitor button, the

 

 

b. Defective pilot

Using match, light the pilot. If the pilot lights, turn off the pilot and trigger

spark ignitor will not

or misaligned

the red piezo ignitor button again. If the pilot lights, an improper gas/air

light the pilot.

electrode (spark at

mixture caused the bad lighting and a longer purge period is recom-

 

 

electrode).

mended. If the pilot will not light, ensure the gap at the electrode and pilot

 

 

is one-eighth(1/8) inch to have a strong spark. If the gap is OK, replace

 

 

the pilot.

 

c. No gas or low

Check the remote shut-offvalves from the fireplace. Usually, there is a

 

gas pressure.

valve near the gas main. There can be more than one (1) valve between

 

 

the fireplace and the main.

 

d. No LP in tank.

Check the LP (propane) tank. You may be out of fuel.

 

 

 

2. The pilot will not

a. Defective ther-

Check that the pilot flame impinges on the thermocouple. Clean and/or

stay lit after care-

mocouple.

adjust the pilot for maximum flame impingement.

fully following the

 

 

lighting instructions.

 

Ensure that the thermocouple connection at the gas valve is fully inserted

 

 

and tight (hand tighten plus 1/4 turn).

 

 

Disconnect the thermocouple from the valve, place one millivolt meter

 

 

lead wire on the tip of the thermocouple and the other meter lead wire on

 

 

the thermocouple copper lead. Start the pilot and hold the valve knob in. If

 

 

the millivolt reading is less than 15mV, replace the thermocouple.

 

b. Defective valve.

If the thermocouple is producing more than 15 millivolts, replace faulty

 

 

valve.

3. The pilot is

a. ON/OFF switch

Check the ON/OFF switch and wires for proper connections. Place the

burning, there is

or wires defective.

jumper wires across the terminals at the switch. If the burner comes on,

no burner flame,

 

replace the defective switch. If the switch is OK, place the jumper wires

the valve knob is

 

across the switch wires at the gas valve. If the burner comes on, the wires

in the ON position,

 

are faulty or connections are bad.

and the ON/OFF

 

 

b. Thermopile may

If the pilot flame is not close enough physically to the thermopile, adjust

switch is in the ON

not be generating

the pilot flame.

position.

sufficient millivolt-

 

 

 

 

age.

Be sure the wire connections from the thermopile at the gas valve termi-

 

 

nals are tight and that the thermopile is fully inserted into the pilot bracket.

 

 

Check the thermopile with a millivolt meter. Take the reading at TH-

 

 

TP&TP terminals of the gas valve. The meter should read 325 millivolts

 

 

minimum, while holding the valve knob depressed in the pilot position,

 

 

with the pilot lit, and the ON/OFF switch in the OFF position. Replace the

 

 

faulty thermopile if the reading is below the specified minimum.

 

 

With the pilot in the ON position, disconnect the thermopile leads from

 

 

the valve. Take a reading at the thermopile leads. The reading should be

 

 

325 millivolts minimum. Replace the thermopile if the reading is below the

 

 

minimum.

 

 

 

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

35

Troubleshooting (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

3. ...Continued

c. Defective valve.

Turn the valve knob to the ON position. Place the ON/OFF

 

 

switch in the ON position. Check the millivolt meter a the ther-

 

 

mopile terminals. The millivolt meter should read greater than

 

 

125mV. If the reading is acceptable, and if the burner does not

 

 

come on, replace the gas valve.

 

 

 

 

d. Plugged burner orifice.

Check the burner orifice for stoppage. Remove stoppage.

 

 

 

 

e. Wall switch or wires are

Follow the corrective action in Symptom and Possible Cause 1.a

 

defective.

above. Check the switch and wiring. Replace where defective.

 

 

 

4. Frequent pilot

a. Pilot flame may be too

Clean thermocouple and adjust the pilot flame for maximum

outage problem.

high or too low, or blowing

flame impingement. Follow lighting instructions carefully.

 

out (high pressure), causing

 

 

pilot safety to drop out.

 

 

 

 

5. The pilot and

a. No LP in tank.

Check the LP (propane) tank. Refill the fuel tank.

main burner ex-

 

 

tinguish while in

b. Inner vent pipe leaking

Check venting system for damage. Replace/repair improperly

operation.

exhaust gases back into the

assembled pipe sections.

 

 

system.

 

 

 

 

 

c. Glass too loose and air

Replace glass panel assembly.

 

tight packet leaks in corners

 

 

after usage.

 

 

 

 

 

d. Bad thermopile or thermo-

Replace if necessary.

 

couple.

 

 

 

 

 

e. Improper vent cap instal-

Check for proper installation and freedom from debris or block-

 

lation.

age.

 

 

 

6. Glass soots.

a. Flame impingement.

Adjust the log set so that the flame does not excessively impinge

 

 

on it.

 

 

 

 

b. Improper air shutter set-

Adjust the air shutter located on the control panel.

 

ting.

 

 

 

 

 

c. Debris around air shutter.

Inspect the opening at the base of the burner. NO MATERIAL

 

 

SHOULD BE PLACED IN THIS OPENING.

 

 

 

7. Flame burns

a. Insufficient oxygen being

Ensure that the vent cap is installed properly and free of debris.

blue and lifts off

supplied.

Ensure that the vent system joints are tight and have no leaks.

burner.

 

Ensure that no debris has been placed at the base of, or in the

 

 

 

 

area of the air holes in the center of the base pan beneath the

 

 

burner.

 

 

Ensure that the glass is tightened properly on the unit, particu-

 

 

larly on top corners.

 

 

 

36

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

B. Intellifire Ignition System

Symptom

Possible Causes

Corrective Actions

 

 

 

1. The ignitor/

a. Incorrect wir-

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are con-

module makes

ing.

nected to correct terminals on module and pilot assembly. Reversed wires

noise, but no

 

at the module may cause system to make sparking noise, but spark may

spark.

 

not be present at pilot hood.

 

 

 

 

b. Loose connec-

Verify no loose connections or electrical shorts in wiring from module to pi-

 

tions or electri-

lot assembly. Rod closest to pilot hood is ignitor. Verify connections under-

 

cal shorts in the

neath pilot assembly are tight; also verify connections are not grounding

 

wiring.

out to metal chassis, pilot burner, pilot enclosure, mesh screen if present,

 

 

or any other metal object.

 

 

 

 

c. Ignitor gap is

Verify gap of igniter to pilot hood. The gap should be approximately .17

 

too large.

inch or 1/8 inch.

 

 

 

 

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor

 

 

wire “I” from module. Place ON/OFF Rocker switch or wall switch in ON

 

 

position. Hold ground wire about 3/16 inch away from “I” terminal on mod-

 

 

ule. If there is no spark at “I” terminal module must be replaced. If there is

 

 

a spark at “I” terminal, module is fine. Inspect pilot assembly for shorted

 

 

sparker wire or cracked insulator around electrode.

 

 

 

2. Pilot won’t

a. Transformer

Verify that transformer is installed and plugged into module. Check volt-

light, there is no

installed correctly.

age of transformer under load at spade connection on module with ON/

noise or spark.

 

OFF switch in ON position. Acceptable readings of a good transformer are

 

 

between 3.2 and 2.8 volts AC.

 

 

 

 

b. A shorted or

Remove and reinstall the wiring harness that plugs into module. Verify

 

loose connection

there is a tight fit. Verify pilot assembly wiring to module. Remove and

 

in wiring configu-

verify continuity of each wire in wiring harness.

 

ration or wiring

 

 

harness.

 

 

 

 

 

c. Improper wall

Verify that 110 VAC power is “ON” to junction box.

 

switch wiring.

 

 

 

 

 

d. Module not

Verify black ground wire from module wire harness is grounded firmly to

 

grounded.

metal chassis of appliance.

 

 

 

 

e. Faulty mod-

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor

 

ule.

wire “I” from module. Place ON/OFF Rocker switch or wall switch in ON

 

 

position. Hold ground wire about 3/16 inch away from “I” terminal on mod-

 

 

ule. If there is no spark at “I” terminal module must be replaced. If there is

 

 

a spark at “I” terminal, module is fine. Inspect pilot assembly for shorted

 

 

sparker wire or cracked insulator around electrode.

 

 

 

3. Pilot lights

a. A shorted or

Verify all connections to wiring diagram in manual. Verify connections

but continues

loose connection

underneath pilot assembly are tight. Verify connections are not grounding

to spark, and

in sensor rod.

out to metal chassis, pilot burner, pilot enclosure or screen if present, or

main burner will

 

any other metal object.

not ignite. (If the

 

 

b. Poor flame

Verify that flame is engulfing sensor rod. If the pilot assembly does not have

pilot continues

to spark after the

rectification or

a ground strap, consider installing one to increase flame rectification. Verify

pilot flame has

contaminated

correct pilot orifice is installed and inlet gas specifications. Flame carries rec-

been lit, flame

sensor rod.

tification current, not the gas. If flame lifts from pilot hood, the circuit is bro-

rectification has

 

ken. A wrong orifice or too high an inlet pressure can cause pilot flame to lift.

not occurred.)

 

The sensor rod may be contaminated. Clean sensor rod with emery cloth.

 

 

 

 

c. Module is not

Verify that module is securely grounded to metal chassis of appliance.

 

grounded.

Verify that wire harness is firmly connected to module.

 

 

 

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

37

Intellifire Ignition System - (continued)

Symptom

Possible Causes

Corrective Actions

 

 

 

3. ...continued

d. Damaged pilot

Verify that ceramic insulator around the sensor rod is not cracked, dam-

 

assembly or dirty

aged, or loose. Verify connection from sensor rod to white sensor wire.

 

sensor rod.

Clean sensor rod with emery cloth to remove any contaminants that may

 

 

have accumulated on sensor rod. Verify continuity with a multimeter with

 

 

ohms set at lowest range.

 

 

 

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor

 

 

wire “I” from module. Place ON/OFF Rocker switch or wall switch in ON po-

 

 

sition. Hold ground wire about 3/16 inch away from “I” terminal on module. If

 

 

there is no spark at “I” terminal module must be replaced. If there is a spark

 

 

at “I” terminal, module is fine. Inspect pilot assembly for shorted sparker

 

 

wire or cracked insulator around electrode.

4. Pilot sparks, but

a. Correct gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet pressure

Pilot will not light.

 

reading is within acceptable limits, inlet pressure must not exceed 14 in.

 

 

W.C.

 

 

 

 

b. Ignitor gap is too

Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in.

 

large.

 

 

 

 

 

c. Module is not

Verify module is securely grounded to metal chassis of appliance.

 

grounded.

 

 

 

 

 

d. Module voltage

Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is

 

output / Valve/Pi-

below 2.7.

 

lot solenoid ohms

 

 

readings.

 

 

 

 

38

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

15 Maintaining and Servicing Appliance

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-upat the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

Turn off gas.

Turn off electricity to appliance.

Disable remote control, if one is present.

Ensure appliance is completely cooled.

After servicing:

Replace any screen or barrier that was removed.

Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

Condition of doors, surrounds and fronts.

Condition of glass, glass assembly and glass seal.

Obstructions of combustion and ventilation air.

Condition of logs.

Condition of firebox.

Burner ignition and operation.

Burner air shutter adjustment

Gas connections and fittings.

Obstructions of termination cap.

Clean:

• Glass

Air passageways, grilles, control compartment

Burner, burner ports

Risk of:

Fire

Delayed ignition or explosion

Exposure to combustion fumes

Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial3-4hours operation.Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when hot.

Turn off appliance after 3-4hours of operation and ALLOW TO COOL.

Remove and clean glass assembly.

Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

39

Inspect

 

Maintenance Tasks

 

 

Doors, Surrounds and

1. Assess condition of screen and replace as necessary.Recommend addition of screen if one is not

Fronts

present.

 

2.

Inspect for scratches, dents or other damage and repair as necessary.

 

 

 

 

3.

Verify no obstructions to airflow through the louvers.

 

 

 

 

4.

Verify maintenance of proper clearance to combustible household objects.

 

 

Gasket Seal, Glass As-

1. Inspect gasket seal and its condition.

sembly and Glass

 

 

2.

Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.

 

 

 

 

3. Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

4.

Verify that latches engage properly, clip studs are not stripped, and glass attachment components are

 

intact and operating properly. Replace as necessary.

 

5.

Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.

 

 

Valve Compartment and

1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas.

Firebox Top

Screw tips that have penetrated the sheet metal are sharp and should be avoided.

 

2.

Remove any foreign objects.

 

 

 

 

3.

Verify unobstructed air circulation.

 

 

 

Logs

1.

Inspect for broken, damaged, or missing logs. Replace as necessary.

 

2.

Verify correct log placement and no flame impingement causing sooting. Correct as necessary.

 

 

 

Firebox

1.

Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.

 

 

 

 

2.

Replace appliance if firebox has been perforated.

 

 

 

Burner Ignition and

1.

Verify burner is properly secured and aligned with pilot or igniter.

Operation

 

 

2.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

 

 

 

 

 

3.

Replace ember materials with new dime-sizeand shape pieces. Do not block ports or obstruct lighting

 

paths.

 

 

 

 

4.

Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.

 

 

 

 

5.

Inspect for lifting or other flame problems.

 

 

 

 

6.

Verify air shutter is clear of dust and debris.

 

 

 

 

7.

Inspect orifice for soot, dirt or corrosion.

 

 

 

 

8.

Verify manifold and inlet pressures. Adjust regulator as required.

 

 

 

 

9.

Inspect pilot flame strength. Clean or replace orifice as necessary.

 

 

 

10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with

 

emery cloth or replace as required.

 

11. Verify millivolt output. Replace as necessary.

Venting

1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

3.

Verify that termination cap clearance to subsequent construction (building additions, decks, fences or

 

sheds) has been maintained.

 

4.

Inspect for corrosion or separation.

 

5.

Verify weather stripping, sealing and flashing remains intact.

 

6.

Inspect draft shield to verify it is not bent, damaged or missing.

 

 

 

Remote controls

1.

Verify operation of remote.

 

 

 

 

2.

Replace batteries in remote transmitters and battery-poweredreceivers.

 

 

 

 

3.

Verify batteries have been removed from battery back-upIPI systems to prevent premature battery

 

failure or leaking.

40

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

 

L

K

 

 

 

 

 

 

 

M

 

 

 

N

 

 

 

I

 

 

J

 

 

 

O

 

 

 

 

R

D

 

ELECTRICAL

 

 

E

F

 

 

ACCESS

GAS LINE

 

 

 

G

ACCESS

 

 

 

Q

 

 

 

 

P

B

C

 

H

A

 

 

 

 

 

 

 

 

 

Figure 16.1 Appliance Dimensions

 

 

 

 

Appliance Dimensions Table

 

 

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SL-550TV-D

Inches

36

31

32-1/2

17

28-1/2

31

8

15-3/4

25-3/4

1/2

1/2

8-1/8

16-1/4

5

5-1/16

2-1/4

1

28-1/2

Millimeters

913

790

827

438

723

789

198

402

327

653

14

206

415

127

129

55

25

726

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SL-750TV-D

Inches

41

36

37-3/4

20-1/2

32

34-1/2

8

-

15-3/8

30-3/4

-

-

-

5

-

-

-

32

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Millimeters

1040

917

960

526

810

878

198

-

390

780

-

-

-

127

-

-

-

815

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SL-950TV-D

Inches

48

43

41-3/4

22

-

38-1/2

-

-

18-7/8

37-3/4

-

-

-

6

6

-

-

36

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Millimeters

1218

1095

1062

559

-

979

-

-

479

958

-

-

-

153

153

-

-

917

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

41

B. Service Parts

SL-550TV-D

Service Parts Diagram

Beginning Manufacturing Date: 1-06

 

Ending Manufacturing Date: ______

11

12

9

8 10

6 13

14

Log Set Assembly

7

 

5

1

 

 

4

 

3

 

2

 

 

Part number list on following page.

42

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

B. Service Parts List

 

 

SL-550TV-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located

 

 

 

AVAILABLE

on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure

 

 

TO SHIP IN 24

correct service parts.

 

 

 

 

HOURS

 

 

 

 

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

 

Log Set Assembly

 

LOGS-SL550-D

Y

1

Log 1 (combined logs)

 

SRV2044-700

 

2

Log 2

 

SRV550-717

 

3

Log 3

 

SRV2044-703

 

4

Log 4

 

SRV2044-701

 

5

Log 5

 

SRV2044-702

 

6

Louver, Top

 

550-259A

 

7

Louver, Bottom

 

550-248A

 

8

Mesh Assembly

 

550-382A

Y

9

Burner NG, LP

Pre 0021076055

530-206A

Y

Post 0021076055

530-018

Y

 

 

10

Glass Door Assembly

 

GLA-550TR

Y

11

Log Grate

 

2044-040

 

12

Base Refractory NG, LP

 

2044-145

 

13

Hood

 

SRV550-175

 

14

Junction Box

 

4021-013

Y

 

Burner Orifice NG (#44C)

 

582-844

Y

 

Burner Orifice LP (#54C)

 

582-854

Y

 

Mineral Wool

 

050-721

 

 

Glass Latch Assembly

 

386-122A

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Additional service part numbers may appear on following page.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

43

B. Service Parts List

 

 

 

SL-550TV-D,SL-550TV-IPI-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on

 

 

 

AVAILABLE

your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct

 

 

TO SHIP IN 24

service parts.

 

 

 

 

 

 

 

 

 

 

HOURS

ITEM

DESCRIPTION

 

 

SERIAL #

PART NUMBER

 

 

 

 

 

STANDING PILOT

 

 

 

Thermocouple

 

 

Pre 0021076055

446-511

Y

 

 

 

Post 0021076055

2103-511

Y

 

 

 

 

 

Thermopile

 

 

Pre 0021076055

060-512

Y

 

 

 

Post 0021076055

2103-512

Y

 

 

 

 

 

Pilot tube

 

 

Pre 0021076055

SRV485-301

Y

 

 

 

Post 0021076055

N/A

 

 

 

 

 

 

 

Conversion Kit NG

 

 

Pre 0021076055

NGK-550TR-C

Y

 

 

 

Post 0021076055

NGKS-550TR-D

Y

 

 

 

 

 

Conversion Kit LP

 

 

Pre 0021076055

LPK-550TR-C

Y

 

 

 

Post 0021076055

LPKS-550TR-D

Y

 

 

 

 

 

Pilot Orifice NG

 

 

Pre 0021076055

446-505

Y

 

 

 

Post 0021076055

2103-116

Y

 

 

 

 

 

Pilot Orifice LP

 

 

Pre 0021076055

446-517

Y

 

 

 

Post 0021076055

2103-117

Y

 

 

 

 

 

Regulator NG

 

 

Pre 0021076055

060-518

Y

 

 

 

Post 0021076055

230-1570

Y

 

 

 

 

 

Regulator LP

 

 

Pre 0021076055

060-519

Y

 

 

 

Post 0021076055

230-1520

Y

 

 

 

 

 

 

IPI CONVERSION KITS

 

 

 

Conversion Kit NG

 

 

 

NGK-550IPIC

Y

 

Conversion Kit LP

 

 

 

LPK-550IPIC

Y

 

Pilot Orifice NG

 

 

Pre 0021076055

446-505

Y

 

 

 

Post 0021076055

593-528

Y

 

 

 

 

 

Pilot Orifice LP

 

 

Pre 0021076055

446-517

Y

 

 

 

Post 0021076055

593-527

Y

 

 

 

 

 

Regulator NG

 

 

 

NGK-DXV

Y

 

Regulator LP

 

 

 

LPK-DXV

Y

44

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

Service Parts

SL-750TV-D

Service Parts Diagram

Beginning Manufacturing Date: 1-06

 

Ending Manufacturing Date: ______

12

13

14

10

11

8

9

15

Log Set Assembly

7

6

5 4

1

3

2

Part number list on following page.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

45

Service Parts List

SL-750TV-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is lo-

 

AVAILABLE

cated on your dealers’ VIP site. When ordering, supply serial and model numbers to

 

 

TO SHIP IN 24

ensure correct service parts.

 

 

 

 

HOURS

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

 

Log Set Assembly

 

LOGS-SL750-D

Y

1

Log 1

 

SRV2045-700

 

2

Log 2

 

SRV530-719

 

3

Log 3

 

SRV530-718

 

4

Log 4

 

SRV2045-703

 

5

Log 5

 

SRV2045-702

 

6

Log 6

 

SRV2045-701

 

7

Mesh Assembly

 

530-382A

Y

8

Burner

Pre 0021073118

530-216A

Y

Post 0021073118

530-019

Y

 

 

9

Glass Door Assembly

 

GLA-750TR

Y

10

Log Grate

 

2045-040

 

11

Base Refractory NG, LP

 

2045-108

 

12

Hood

 

SRV530-175

 

13

Louver, Top

 

530-259A

 

14

Louver, Bottom

 

530-237A

 

15

Junction Box

 

4021-013

Y

 

Burner Orifice NG (#42C)

 

582-842

Y

 

Burner Orifice LP (#53C)

 

582-853

Y

 

Mineral Wool

 

050-721

 

 

Glass Latch Assembly

 

386-122A

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Additional service part numbers may appear on following page.

46

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

B. Service Parts List

 

 

SL-750TV-D,SL-750TV-IPI-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is

 

 

 

AVAILABLE

located on your dealers’ VIP site. When ordering, supply serial and model numbers

 

 

TO SHIP IN 24

to ensure correct service parts.

 

 

 

 

 

 

HOURS

ITEM

DESCRIPTION

 

SERIAL #

PART NUMBER

 

 

 

 

STANDING PILOT

 

 

 

Thermocouple

 

Pre 0021076242

446-511

Y

 

 

Post 0021076242

2103-511

Y

 

 

 

 

Thermopile

 

Pre 0021076242

060-512

Y

 

 

Post 0021076242

2103-512

Y

 

 

 

 

Pilot tube

 

Pre 0021076242

SRV485-301

Y

 

 

Post 0021076242

N/A

Y

 

 

 

 

Conversion Kit NG

 

Pre 0021076242

NGK-750TR-C

Y

 

 

Post 0021076242

NGKS-750TR-D

Y

 

 

 

 

Conversion Kit LP

 

Pre 0021076242

LPK-750TR-C

Y

 

 

Post 0021076242

LPKS-750TR-D

Y

 

 

 

 

Pilot Orifice NG

 

Pre 0021076242

446-505

Y

 

 

Post 0021076242

2103-116

Y

 

 

 

 

Pilot Orifice LP

 

Pre 0021076242

446-517

Y

 

 

Post 0021076242

2103-117

Y

 

 

 

 

Regulator NG

 

Pre 0021076242

060-518

Y

 

 

Post 0021076242

230-1570

Y

 

 

 

 

Regulator LP

 

Pre 0021076242

060-519

Y

 

 

Post 0021076242

230-1520

Y

 

 

 

 

 

IPI CONVERSION KITS

 

 

 

Conversion Kit NG

 

 

NGK-750IPIC

Y

 

Conversion Kit LP

 

 

LPK-750IPIC

Y

 

Pilot Orifice NG

 

Pre 0021073118

446-505

Y

 

 

Post 0021073118

593-528

Y

 

 

 

 

Pilot Orifice LP

 

Pre 0021073118

446-517

Y

 

 

Post 0021073118

593-527

Y

 

 

 

 

Regulator NG

 

 

NGK-DXV

Y

 

Regulator LP

 

 

LPK-DXV

Y

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

47

Service Parts

SL-950TV-D

Service Parts Diagram

Beginning Manufacturing Date: 1-06

 

Ending Manufacturing Date: ______

10

11

8

7 9

13

12

15

14

Log Set Assembly

6

5 4

1

3

2

Part number list on following page.

48

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

Service Parts List

 

 

SL-950TV-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is

 

 

 

AVAILABLE

located on your dealers’ VIP site. When ordering, supply serial and model numbers

 

to ensure correct service parts.

 

 

TO SHIP IN 24

 

 

 

 

HOURS

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

 

Log Set Assembly

 

LOGS-SL750-D

Y

1

Log 1

 

SRV2045-700

 

2

Log 2

 

SRV530-719

 

3

Log 3

 

SRV530-718

 

4

Log 4

 

SRV2045-702

 

5

Log 5

 

SRV2045-703

 

6

Log 6

 

SRV2045-701

 

7

Mesh Assembly

 

560-382A

Y

8

Burner NG, LP

Pre 0021076046

534-211A

Y

Post 0021076046

534-017

Y

 

 

9

Glass Door Assembly

 

GLA-950TR

Y

10

Log Grate

 

2045-040

 

11

Base Refractory NG, LP

 

2046-108

 

12

Hood

 

SRV560-175

 

13

Louver, Top

 

560-257A

 

14

Louver, Bottom

 

560-259A

 

15

Junction Box

 

4021-013

Y

 

Burner Orifice NG (#36C)

 

582-836

Y

 

Burner Orifice LP (#51C)

 

582-851

Y

 

Mineral Wool

 

050-721

 

 

Glass Latch Assembly

 

386-122A

Y

 

Touch Up Paint

 

TUP-GBK-12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Additional service part numbers may appear on following page.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

49

Service Parts List

 

 

SL-950TV-D,SL-950TV-IPI-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is

 

 

 

AVAILABLE

located on your dealers’ VIP site. When ordering, supply serial and model numbers

 

to ensure correct service parts.

 

 

 

TO SHIP IN 24

 

 

 

 

 

HOURS

ITEM

DESCRIPTION

 

SERIAL #

PART NUMBER

 

 

 

 

STANDING PILOT

 

 

 

Thermocouple

 

Pre 0021076046

446-511

Y

 

 

Post 0021076046

2103-511

Y

 

 

 

 

Thermopile

 

Pre 0021076046

060-512

Y

 

 

Post 0021076046

2103-512

Y

 

 

 

 

Pilot tube

 

Pre 0021076046

SRV485-301

Y

 

 

Post 0021076046

N/A

Y

 

 

 

 

Conversion Kit NG

 

Pre 0021076046

NGK-950TR-C

Y

 

 

Post 0021076046

NGKS-950TR-D

Y

 

 

 

 

Conversion Kit LP

 

Pre 0021076046

LPK-950TR-C

Y

 

 

Post 0021076046

LPKS-950TR-D

Y

 

 

 

 

Pilot Orifice NG

 

Pre 0021076046

446-505

Y

 

 

Post 0021076046

2103-116

Y

 

 

 

 

Pilot Orifice LP

 

Pre 0021076046

446-517

Y

 

 

Post 0021076046

2103-117

Y

 

 

 

 

Regulator NG

 

Pre 0021076046

060-518

Y

 

 

Post 0021076046

230-1570

Y

 

 

 

 

Regulator LP

 

Pre 0021076046

060-519

Y

 

 

Post 0021076046

230-1520

Y

 

 

 

 

 

IPI CONVERSION KITS

 

 

 

Conversion Kit NG

 

 

NGK-950IPIC

Y

 

Conversion Kit LP

 

 

LPK-950IPIC

Y

 

Pilot Orifice NG

 

Pre 0021076046

446-505

Y

 

 

Post 0021076046

593-528

Y

 

 

 

 

Pilot Orifice LP

 

Pre 0021076046

446-517

Y

 

 

Post 0021076046

593-527

Y

 

 

 

 

Regulator NG

 

 

NGK-DXV

Y

 

Regulator LP

 

 

LPK-DXV

Y

50

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

Service Parts

SL-550 /750 /950TV-D

Valve Assembly Parts List

 

Beginning Manufacturing Date: 1-06

 

 

Ending Manufacturing Date: ______

Standing Pilot

3

 

Valve Assembly

 

 

1

 

 

5

 

 

4

 

 

6

 

12

 

 

7

 

 

14

 

8

2

11

 

13

 

 

 

10

 

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on

 

AVAILABLE

your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct

 

 

TO SHIP IN 24

service parts.

 

 

 

 

 

 

HOURS

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

1

Burner Neck Gasket

 

2045-407

 

2

Thermostat Wire Assembly

 

2045-024

Y

 

Pilot Assembly NG

Pre 0021076055

530-510A

Y

3

Post 0021076055

2103-010

Y

 

Pilot Assembly LP

Pre 0021076055

530-511A

Y

 

 

Post 0021076055

2103-011

Y

 

 

4

Valve Bracket

Pre 0021076055

2025-101

 

Post 0021076055

2025-101/2044-155

 

 

 

 

5

Valve Plate Gasket

 

530-431

 

6

Flex Ball Valve Assembly

 

302-320A

Y

 

Valve NG

Pre 0021076055

060-522

Y

7

Post 0021076055

230-0710

Y

 

Valve LP

Pre 0021076055

060-523

Y

 

 

Post 0021076055

230-0720

Y

 

 

8

Flexible Gas Connector

 

530-302A

Y

9

Piezo Ignitor

 

291-513

Y

 

Pilot Bracket

Pre 0021076055

530-164

 

 

Post 0021076055

N/A

 

 

 

 

 

High Limit Switch

 

066-531

Y

 

Jumper Wires

 

2012-206

Y

 

1/4 Female Spades Wire

 

505-501A

Y

 

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

51

Service Parts

 

SL-550 /750 /950TV-D-IPI

Valve Assembly Parts List

 

Beginning Manufacturing Date: 1-06

 

Ending Manufacturing Date: ______

 

 

IPI Valve Assembly

3

 

 

 

1

 

 

5

 

 

4

 

 

6

 

12

 

 

7

 

 

14

 

8

2

11

 

13

 

 

10

 

 

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on

 

AVAILABLE

your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct

 

 

TO SHIP IN 24

service parts.

 

 

 

 

 

 

HOURS

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

1

Burner Neck Gasket

 

2045-407

 

 

 

 

 

 

2

Thermostat Wire Assembly

 

2045-024

Y

 

Pilot Assembly NG

Pre 0021076055

385-510A

Y

3

Post 0021076055

2090-012

Y

 

 

 

 

 

Pilot Assembly LP

Pre 0021076055

385-511A

Y

 

 

 

 

 

 

Post 0021076055

2090-013

Y

 

 

4

Valve Bracket

 

2025-101

 

5

Valve Plate Gasket

 

530-431

 

 

 

 

 

 

6

Flex Ball Valve Assembly

 

302-320A

Y

7

Valve NG

 

750-500

Y

Valve LP

 

750-501

Y

 

 

8

Flexible Gas Connector

 

530-302A

Y

 

 

 

 

 

10

Module

 

593-592

Y

11

Module Wire Assembly

 

593-590A

Y

12

Battery Pack

 

593-594A

Y

 

 

 

 

 

13

3 Volt Transformer

 

593-593A

Y

 

 

 

 

 

14

Jumper Wires

 

2012-206

Y

 

Pilot Bracket

Pre 0021076055

560-164

 

 

Post 0021076055

N/A

 

 

 

 

 

 

 

 

 

 

Pilot Assembly Support

Pre 0021076055

397-121

 

 

 

 

 

 

Post 0021076055

N/A

 

 

 

 

 

High Limit Switch

 

066-531

Y

 

5” Wire Harness

 

065-577A

Y

 

 

 

 

 

 

1/4 Female Spades Wire

 

505-501A

Y

 

 

 

 

 

 

Ground Strap

Pre 0021076055

385-512

 

 

Post 0021076055

N/A

 

 

 

 

52

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

 

C. Limited Lifetime Warranty

LIMITED LIFETIME WARRANTY

HEAT & GLO GAS APPLIANCE PRODUCTS

BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEAT & GLO will replace or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.

EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in material or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and limitations described below.

CONDITIONS, EXCLUSIONS AND LIMITATIONS:

1.This warranty applies to the original owner only and is nontransferable.

2.This warranty applies only to Products installed in the United States of America or Canada.

3.This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an expedient and cost-effectivemanner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT.

4.Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-YearWarranty.

5.Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty unless expressly authorized and approved by HEAT & GLO in writing.

6.Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.

7.This warranty will be void if:

a)The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.

b)Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved by HEAT & GLO in writing.

c)Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.

d)The Product is damaged due to shipping, improper handling, accident, abuse or misuse.

e)Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.

f ) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HEAT & GLO dealer or supplier.

NOTES TO CUSTOMER:

1.In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual servicing by an authorized HEAT & GLO dealer.

2.Please complete this information and retain this warranty in a safe place for future reference: Installation Date:______

Model #:_________________ Serial #:______________ Installing Contractor:_________________________

3.HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products.

© 2005 Hearth & Home Technologies Inc.

060-981D3/05

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

53

D. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568,

5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474,

6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Printed in U.S.A. - Copyright 2006

54

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07