Heat & Glo LifeStyle SL-550TV-IPI-D User Manual

Size:
3.46 Mb
Download

Owner’s Manual

Installation and Operation

Models:

SL-550TV-D,SL-550TV-IPI-D

SL-750TV-D,SL-750TV-IPI-D

SL-950TV-D,SL-950TV-IPI-D

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the Commonwealth of Massachusetts:

installation must be performed by a licensed plumber or gas fitter;

a CO detector shall be installed in the room where the appliance is installed.

WARNING

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

Keep children away.

CAREFULLY SUPERVISE children in same room as appliance.

Alert children and adults to hazards of high temperatures.

Do NOT operate with protective barriers open or removed.

Keep clothing, furniture, draperies and other combustibles away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. Do NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trained

professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, abrand of Hearth & Home Technologies, Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

Not for usewithsolidfuel.

(Nedoitpasentreutiliseavecuncombustiblesolide).

TypeofGas (Sorte De Gaz): Thisappliancemustbeinstalledinaccordancewithlocalcodes, ifany;ifnot,followANSIZ223.1intheUSAorCAN/CGAB149 installationcodes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum PermissibleGasSupplyfor PurposesofInputAdjustment.

 

 

 

ApprovedMinimum (De Gaz) Acceptable

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumPressure(Pression)

 

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

Minimum ManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

TotalElectricalRequirements: 000Vac,00Hz.,lessthan00Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INCANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN.INPUTBTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICESIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

- Table of Contents-

Section 1: Listing and Code Approvals

 

 

A. Appliance Certification...................................

4

 

B. Glass Specifications ......................................

4

 

C. BTU Specifications ........................................

4

 

D. High Altitude Installations ..............................

5

 

E. Non-combustibleMaterials Specification.......

5

 

F. Combustible Materials Specification..............

5

Section 2:

Getting Started

 

 

A. Design and Installation Considerations .........

6

 

B. Negative Pressure.........................................

7

 

C. Tools and Supplies Needed...........................

8

 

D. Inspect Appliance and Components..............

8

Section 3: Framing and Clearances

 

Î

A. Selecting Appliance Location.........................

9

Î

B. Constructing the Appliance Chase ..............

10

 

C. Clearances ..................................................

10

 

D. Mantel Projections........................................

11

Section 4:

Termination Locations

 

 

A. Vent Termination Minimum Clearances .......

12

Section 5: Vent Information and Diagrams

 

 

A. Vent Guidelines ...........................................

13

 

B. Vent System Configuration..........................

13

Section 6: Vent Clearances and Framing

 

 

A. Pipe Clearances to Combustibles ...............

15

 

B. Wall Penetration Framing ............................

15

 

C. Vertical Penetration Framing .......................

15

Section 7:

Appliance Preparation

 

 

A. Installing Outside Air Kit Damper Assembly..

16

 

B. Gas/Electrical Connections .........................

16

 

C. Securing and Leveling Appliance ................

17

Section 8: Installing Vent Pipe

 

 

A. Assembly of Vent Sections..........................

18

 

B. Attaching Vent to Firebox ............................

18

 

C. Securing Vent Sections ..............................

18

Section 9:

Gas Information

 

 

A. Fuel Conversions.........................................

19

 

B. Gas Pressures.............................................

19

 

C. Gas Connection...........................................

19

Section 10:

Electrical Information

 

 

A. Recommendation for Wire ........................

21

 

B. Connecting to the Appliance .....................

21

 

C. Intellifire Ignition System Wiring................

21

 

D. Standing Pilot Ignition System Wiring.......

22

 

E. Junction Box Installation ...........................

23

 

F.

Wall Switch Installation for Fan.................

23

Section 11:

Finishing

 

 

A. Mantel Projections ....................................

24

 

B.

Facing Material .........................................

24

Section 12:

Appliance Setup

 

 

A. Remove Shipping Materials......................

25

 

B. Remove Grate Shipping Support..............

25

 

C. Clean the appliance ..................................

25

 

D. Accessories ..............................................

25

 

E. Install the Refractory.................................

25

 

F. Lava Rock, Vermiculite, Rockwool

 

 

 

and Ember Placement ..............................

25

 

G. Positioning the Logs .................................

26

 

H. Glass Assembly ........................................

30

 

I.

Screen Mesh.............................................

30

 

J.

Grilles and Trim.........................................

30

 

K. Hood .........................................................

30

 

L. Shutter Settings ........................................

30

Section 13:

Operating Instructions

 

 

A. Before Lighting Appliance .........................

31

 

B. Check Appliance Draft ..............................

31

 

B. Lighting Appliance.....................................

32

 

C. After Appliance is Lit .................................

34

 

D. Frequently Asked Questions.....................

34

Section 14:

Troubleshooting

 

 

A. Standing Pilot Ignition System ..................

35

 

B. Intellifire Ignition System...........................

37

Section 15:

Maintaining and Servicing Appliance...........

39

Section 16:

Reference Materials

 

 

A. Appliance Dimension Diagram .................

41

 

B. Service Parts ............................................

42

 

C. Warranty ...................................................

52

 

D. Contact Information ..................................

53

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

3

1Listing and Code Approvals

A. Appliance Certification

MODELS: SL-550TV-D,SL-750TV-D,SL-950TV-D,

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: B-VentDecorative

STANDARD: ANSIZ21.50-2002• CGA2.2

This product is listed to ANSI standards for “Vented Gas Fireplaces” and “Gas Fired Appliances for Use at High Altitudes”.

This model (natural gas and propane) can be installed in a bedroom (in the United States) which has a total volume of unconfined space appropriate to the particular installation. Refer to the National Fuel Gas Code ANSI Z223.1/

NFPA54 (current edition), The Uniform Mechanical Code - (current edition), and local Building Officials for the options allowed in obtaining an effective bedroom volume of unconfined space.

This model (natural gas and propane) can be installed in a bedroom (in Canada) if a thermostat (Model WH-STAT)is installed with the unit. Consult local code authorities. Detailed installation instructions for ModelWH-STATare included with the kit.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

Heat & Glo Quality Systems registered by SGS ICS

B. Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with theNational Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and theCAN/CGA B149 Installation Codes in Canada.

C. BTU Specifications

Model(s)

 

Maximum

Minimum

Orifice

 

Input BTU/h

Input BTU/h

Size

U.S. (0-2000ft.) or Canada(2000-4500ft.)

(DMS)

SL-550TV-D

US

21,000

12,000

44

 

 

 

 

SL-550TV-IPI-D

CAN

18,900

10,800

45

 

 

 

 

 

 

SL-550TV-D(LP)

US

20,000

N/A

54

 

 

 

 

SL-550TV-IPI-D(LP)

CAN

18,000

N/A

55

 

 

 

 

 

 

SL-750TV-D

US

23,000

16,000

42

 

 

 

 

SL-750TV-IPI-D

CAN

20,700

14,400

43

 

 

 

 

 

 

SL-750TV-D(LP)

US

23,000

N/A

53

 

 

 

 

SL-750TV-IPI-D(LP)

CAN

20,700

N/A

54

 

 

 

 

 

 

SL-950TV-D

US

30,000

21,000

36

 

 

 

 

SL-950TV-IPI-D

CAN

27,000

18,900

37

 

 

 

 

 

 

SL-950TV-D(LP)

US

30,000

21,000

51

 

 

 

 

SL-950TV-IPI-D(LP)

CAN

27,000

N/A

52

 

 

 

 

 

 

4

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

D. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750oC,shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

5

2 Getting Started

A. Design and Installation Considerations

Heat & Glo B-typevent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

Where the appliance is to be installed. See Sections 3 and 4.

The vent system configuration to be used. See Sections

5 and 6.

Gas supply piping. See Sections 7 and 9.

Electrical wiring. See Sections 7 and 10.

Framing and finishing details. See Sections 3, 6 and 11.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.See Section 10.

WARNING

Fire Risk

Explosion Risk

Keep appliance dry.

Water may damage controls.

Mold or rust may cause odors.

6

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

B. Negative Pressure

WARNING

Asphyxiation Risk.

Negative pressure can cause spillage of combustion fumes and soot.

Fireplace needs to draft properly for safety.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

Preventing negative pressure

Location of fireplace and chimney

Negative pressure results from the imbalance of air available for the fireplace to operate properly. Causes for this imbalance include:

Exhaust fans (kitchen, bath, etc.)

Range hoods

Combustion air requirements for furnaces, water heaters and other combustion appliances

Clothes dryers

Location of return-airto furnace or air conditioning

Imbalances of the HVAC air handling system

Upper level air leaks (recessed lighting, attic hatch opening, duct leaks)

To minimize the effects of negative air pressure, the following must be considered:

Install the fresh air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace.

Avoid installing the fireplace near doors, walkways or small isolated spaces.

Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted ductwork and air handler joints and seams taped or sealed.

Basement installations should be avoided due to stack effect. Stack effect creates negative pressure in lower levels. Hearth & Home Technologies recommends the use of direct vent fireplaces in basements.

Location of the fireplace and chimney will affect performance. As shown in Figure 2.1, the chimney should:

Be installed through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-downof the fire.

Penetrate the highest part of the roof. This minimizes the effects of wind turbulence.

Be located away from trees, adjacent structures, uneven roof lines and other obstructions.

Offsets can restrict draft so their use should be minimized. Consider the fireplace location relative to floor and ceiling and attic joists.

Recommended Recommended

Location Location

Marginal

Location

Location

Not

Recommended

Location NOT

Recommended

Leeward

Multi-levelRoofs

Figure 2.1

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

7

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw

Framing material

Pliers

Hi temp caulking material

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Tape measure

Manometer

Voltmeter

Non-corrosiveleak check solution

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews One 1/4 inch female connection (for optional fan).

D. Inspect Appliance and Components

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components.

Report suspected damaged parts to dealer.

The following B-ventcomponents are needed for installation (see Figure 2.2).

Fireplace Box

Pipe Components

Firestops

Attic Insulation Shield

Elbows

Strapping

Roof Flashing or Chase Top

Termination Cap

Storm Collar

Carefully remove the appliance and components from the packaging.

The vent system components and trim doors are shipped in separate packages.

The gas logs may be packaged separately and must be field installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

VERTICAL TERMINATION CAP

STORM COLLAR

ROOF FLASHING

OR CHASE TOP

ATTIC INSULATION SHIELD

FIRESTOP SPACER

GAS B-VENT

PIPE SECTION (S)

Figure 2.2 Typical Vertical Installation

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

8

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

3 Framing and Clearances

NOTE:

 

WARNING

Illustrations reflect typical installations and are FOR

 

 

DESIGN PURPOSES ONLY.

Fire Risk

Illustrations/diagrams are not drawn to scale.

Provide adequate clearance:

Actual installation may vary due to individual design

Around air openings

 

preference.

 

To combustibles

 

 

 

 

For service access

A. Selecting Appliance Location

Locate appliance away from traffic areas.

 

 

When selecting a location for your appliance it is important to

consider the required clearances to walls (see Figure 3.1). NOTE: For actual appliance dimensions refer to

Section 16.

A

F

TOP VENT

B

ALCOVE

INSTALLATION D

A

B

C

TOP VENT

TOP VENT

B

E

Model

A

B

C

D

E

F

 

 

 

 

 

 

 

 

SL-550TV-D

Inches

41-1/2

37

58-3/4

 

16-1/4

1/2

 

 

 

 

 

 

 

Millimeters

1054

940

1492

 

413

13

 

 

 

 

 

 

 

36 Inches

 

 

 

Inches

45

42

63-3/4

16-1/4

1/2

SL-750TV-D

914 Millimeters

 

 

 

 

 

 

Millimeters

1143

1067

1619

Maximum

413

13

 

 

 

 

 

 

 

 

 

 

 

SL-950TV-D

Inches

50

49

70-3/4

 

16-1/4

1/2

 

 

 

 

 

 

 

Millimeters

1270

1245

1792

 

413

13

 

 

 

 

 

 

 

 

 

 

In addition to these framing dimensions, also reference the following sections:

Clearances and Mantel Projections (Sections 3.C and 3.D)

Vent Clearances and Framing (Section 6).

ÎFigure 3.1 Appliance Locations

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07

9

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase.

Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts in cold climates, the firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

WARNING

Fire Risk.

Odor Risk.

Install appliance on hard metal or wood surfaces extending full width and depth of appliance.

Do NOT install appliance directly on carpeting, vinyl, tile or any combustible material other than wood.

Do NOT place furniture or any other combustible household objects within 36 inches of the appliance front.

WARNING

Fire Risk.

Construct chase to all clearance specifications in manual.

Locate and install appliance to all clearance

specifications in manual

A

E

 

 

 

 

 

F

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

 

 

I

 

 

 

 

 

 

 

 

 

 

 

Models

A

B

C

D

E

F

G

H

I

J

SL-550TV-D

Inches

10

33

16-1/4

37

31

0

0

1/2

1/2

36

mm

254

838

413

940

787

0

0

13

13

914

 

SL-750TV-D

Inches

10

38-1/4

16-1/4

42

31

0

0

1/2

1/2

36

mm

254

971

413

1067

787

0

0

13

13

914

 

SL-950TV-D

Inches

10

42-1/4

16-1/4

49

31

0

0

1/2

1/2

36

mm

254

1073

413

1245

787

0

0

13

13

914

 

Î Figure 3.2 Clearances to Combustibles

 

 

 

 

 

 

 

 

 

 

10

Heat & Glo • SL-550 /750 /950TV-D2053-985Rev. J • 4/07