Heat & Glo LifeStyle PALOMA-BZ-MOD User Manual

Size:
2.9 Mb
Download

Owner’s Manual

Installation and Operation

Model(s):

PALOMA-BZ-MOD

PALOMA-GR-MOD

PALOMA-GY-MOD

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual

and maintenance

these instructions for safe

party responsible for

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance.

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

In the Commonwealth of Massachusetts:

installation must be performed by a licensed plumber or gas fitter;

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas(Sorte De Gaz): This appliance must beinstalled in accordance with local codes, if any;if not, follow ANSI Z223.1in the USAor CAN/CGA B149 installation codes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

 

 

Approved Minimum(De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Minimum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN CANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

Table of Contents

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4 E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 4 F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4 G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 H. Requirements for the Commonwealth of Massachusetts. . 5

2 Getting Started

A. Design and Installation Considerations . . . . . . . . . . . . . . . 6

B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6

C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 6

3 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7 B. Clearances to Combustibles . . . . . . . . . . . . . . . . . . . . . . . 8

4 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . . 9

5 Vent Information

A. Venting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 D. How to Use the Vent Graph . . . . . . . . . . . . . . . . . . . . . . . 12 E. Venting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 F. Horizontal Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 G. Vertical Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 H. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 18 I. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 19 J. Cathedral Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 K. Class A Metal Chimney . . . . . . . . . . . . . . . . . . . . . . . . . . 20 L. Existing Masonry Chimney. . . . . . . . . . . . . . . . . . . . . . . . 21 M. Slim Line Wall Thimble. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8 Appliance Setup

A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 31 B. Unbolting Appliance from the Pallet . . . . . . . . . . . . . . . . . 31 C. Leveling and Lagging Down the Appliance . . . . . . . . . . . 32 D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 E. Top to Rear Vent Conversion . . . . . . . . . . . . . . . . . . . . . . 33 F. Shutter Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 G. Installing the Vent Restrictor. . . . . . . . . . . . . . . . . . . . . . . 34 H. Installing Rock Media and Ember Material. . . . . . . . . . . . 35 I. Optional Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 J. Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 K. Front Door Glass Assembly Replacement . . . . . . . . . . . . 42 L. Inner Glass Door Assembly Replacement . . . . . . . . . . . . 42

9 Operating Instructions

A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 43 B. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 C. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 44 D. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 E. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 45

10 Troubleshooting

A. IntelliFire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 47

11 Maintaining and Servicing Appliance

A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

12 Reference Materials

A.

Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . .

50

 

B.

Vent Components Diagram . . . . . . . . . . . . . . . . . . . . . . .

51

 

C.

Vent Components List . . . . . . . . . . . . . . . . . . . . . . . . . . .

52

D.

Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

53

E.

Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . .

57

 

F.

Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

59

 

7 Electrical Information

A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 28 B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 28 C. IntelliFire® Ignition System Wiring . . . . . . . . . . . . . . . . . . 28 D. Loss of Power and Battery Backup Usage. . . . . . . . . . . . 29 E. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 30

= Contains updated information.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

3

1 Listing and Code Approvals

A. Appliance Certification

MODELS: PALOMA-BZ-MOD,PALOMA-GR-MOD,

PALOMA-GY-MOD

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Vented Gas Fireplace Heater

STANDARD: ANSIZ21.88b-2008• CSA2.33a-2008

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

Manufactured Home or Mobile Home installation may occur only after the home is site located and must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4.

When installed, the appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

D. High Altitude Installations

Omni-TestLaboratories, Inc. listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and 0 to 4500 feet in Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/ or gas control which has been under water.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750ºC, shall be considered non-combustible materials.

B. Glass Specifications

This appliance is equipped with 5 mm ceramic glass behind the curved glass. Replace glass only with 5 mm ceramic glass. Please contact your dealer for replacement glass.

Note: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

C. BTU Specifications

Model

Maximum

Minimum

Orifice

*Steady

**P.4

(US or Canada)

Input

Input

Size

State

%

 

BTU/h

BTU/h

(DMS)

Efficiency %

 

Paloma (NG)

28,000

20,000

38

81

71

Paloma (LP)

26,000

19,000

53

81

72

*Maximum Vent Blower On **Canada Only

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

4

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

H.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2) (a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

5

2 Getting Started

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

WARNING

Keep appliance dry.

• Mold or rust may cause odors.

• Water may damage controls.

B. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

C. Inspect Appliance and Components

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

If packaged separately, the rock set must be installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the rock set or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

Reciprocating saw

Framing material

Pliers

Noncorrosive leak check solution or combustible gas detector

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Wrenches

Ratchets/Sockets

Allen Wrench Set

Manometer

Voltmeter

Tape measure

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews

One 1/4 inch female connection (for optional fan)

Caulk with a minimum of 300ºF continuous exposure rating

6

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

3 Framing and Clearances

Note:

Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

Illustrations/diagrams are not drawn to scale.

Actual installation may vary due to individual design preference.

A.Selecting Appliance Location

When selecting a location for your appliance it is important to consider the required clearances to walls (see figure 3.1).

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I

 

K

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

E

 

K

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“A” MEASUREMENT IS FROM APPLIANCE TOP, NOT SIDE

 

 

 

 

 

 

 

 

 

ALCOVE

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

A

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

Model

A

B

C

D

E

F

G

H

I

J

K

Inches

6

10-1/8

12-1/8

54

36

30-3/4

13-1/4

13-1/4

1

15-1/2

5

Paloma

152

257

308

1372

914

781

337

337

25

394

127

Millimeters

Figure 3.1

 

 

 

 

 

 

 

 

 

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

 

7

B. Clearances to Combustibles

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTE: For actual appliance dimensions refer to Section 12.

It is permissible to place the appliance on carpet.

CAUTION

Some carpet materials may be sensitive to radiant heat from the appliance causing discoloration or odor.

Note: Flooring beneath appliance may reach 90 degrees plus room ambient temperature. Check with flooring manufacturer for maximum temperature allowed on flooring surfaces.

WARNING

Fire Risk.

Locate and install appliance to all clearance specifications in manual.

WARNING

Fire Risk.

Odor Risk.

Tipping Risk

Install gas stove on a stable, level platform/ floor strong enough to support gas stove without tipping.

USE wood flooring, ceramic tile, brick hearth

or high pressure laminate flooring applied directly over the sub-flooringmaterial.

8

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

4 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

(See Figure 4.4 for specific clearances)

Figure 4.1

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 4.2 Minimum height from roof to lowest discharge opening

Figure 4.2 specifies minimum vent heights for various pitched roofs.

A

B

6 in. (minimum) up to 20 in.

18 in. minimum

152 mm/508 mm

457 mm

20 in. and over

0 in. minimum

Gas, Wood or Fuel Oil

Termination Cap

B

A *

Gas

Termination

Cap **

*If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

**In a staggered installation with both gas and wood or fuel oil terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Figure 4.3 Staggered Termination Caps

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

P

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Q

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(See Note 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

S

Electrical

 

S

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

= VENT TERMINAL

X = AIR SUPPLY INLET

 

 

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

=

12 inches.................

clearances above grade, veranda,

 

L**

=

7 ft..........................

 

clearance above paved

 

 

 

 

 

(See Note 1)

porch, deck or balcony

 

 

 

 

 

 

 

 

(See Note 1)

 

sidewalk or a paved driveway

 

B

=

12 inches

clearances to window or door

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

located on public property

 

 

M*** =

18 inches

 

clearance under veranda, porch,

 

 

 

 

 

 

 

 

 

 

that may be opened, or to perma-

 

 

 

 

 

 

 

 

 

 

 

 

nently closed window. (Glass)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

deck, balcony or overhang

 

D*

=

18 inches.................

vertical clearance to unventilated

 

 

 

 

 

 

 

 

42 inches ...............

 

vinyl

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

soffit or to ventilated soffit located

 

S

=

 

6 inches.................

 

clearance from sides of electri-

 

 

 

 

 

 

 

 

 

 

above the terminal

 

 

 

 

 

 

 

 

 

(See Note 5)

 

cal service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*30 inches................

for vinyl clad soffits and below

 

T

=

12 inches................

 

clearance above electrical

 

 

 

 

 

 

 

 

 

 

electrical service

 

 

 

 

 

 

 

 

(See Note 5)

 

service

 

 

 

 

 

 

 

 

 

 

 

 

 

F

=

9 inches..................

clearance to outside corner

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Alcove Applications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

=

...................6 inches

clearance to inside corner

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

 

 

=

6 inches

 

non-vinylsidewalls

 

 

 

 

H

=

3 ft. (Canada)

not to be installed above a gas

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 inches

 

vinyl sidewalls

 

 

 

 

 

 

 

 

 

 

 

 

 

 

meter/regulator assembly within 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

 

=

8 ft.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

feet (90 cm) horizontally from the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

center-lineof the regulator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QMIN

 

 

 

 

 

 

RMAX

 

 

 

 

 

I

=

3 ft...........................

clearance to gas service regulator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 cap

 

 

 

 

3 feet

 

 

 

2 x Q ACTUAL

 

 

 

 

 

 

 

 

 

 

 

 

vent outlet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J

=

9 inches (U.S.A.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 caps

 

 

 

 

6 feet

 

 

 

1 x Q ACTUAL

 

 

 

 

 

 

 

12 inches (Canada) clearance to non-mechanical

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 caps

 

 

 

 

9 feet

 

 

2/3 x Q ACTUAL

 

 

 

 

 

 

 

 

 

 

 

 

air supply inlet to building or the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

combustion air inlet to any other

 

 

 

 

 

 

 

 

4 caps

 

 

 

 

12 feet

 

 

1/2 x Q ACTUAL

 

 

 

 

 

 

 

 

 

 

 

 

appliance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

K

=

3 ft. (U.S.A.)

 

 

 

 

 

QMIN = # termination caps x 3

RMAX = (2 / # termination caps) x QACTUAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

...........6 ft. (Canada)

clearance to a mechanical (pow-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ered) air supply inlet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

**a vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

***only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor, or meets Note 2.

NOTE 1: On private property where termination is less than 7 feet above a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap shield is suggested. (See vents components page)

NOTE 2: Termination in an alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions specified for vinyl ornon-vinylsiding and soffits.1. There must be 3 feet minimum between termination caps.2. All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below the termination cap.3. All gravity air intakes within 3 feet of a termination cap must be a minimum of 1 foot below the termination cap.

Figure 4.4 Minimum Clearances for Termination

NOTE 3: Local codes or regulations may require different clearances.

NOTE 4: Termination caps may be hot. Consider their proximity to doors or other traffic areas.

NOTE 5: Location of the vent termination must not interfere with access to the electrical service.

WARNING: In the U.S: Vent system termination isNOT permitted in screened porches. You must follow side wall, overhang and ground clearances as stated in the instructions.

In Canada: Vent system termination isNOT permitted in screened porches. Vent system termination is permitted in porch areas with two or more sides open. You must follow all side walls, overhang and ground clearances as stated in the instructions.

Heat & Glo assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

10

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

5 Vent Information

A. Venting Components

In order to comply with applicable codes and product warranties, use only following venting components:

Hearth & Home Technologies (HHT)

Simpson Dura-Vent(SDV)

DO NOT USE FIELD-FABRICATEDVENTING COMPONENTS. Refer to the venting manufacturer’s instructions.

This product is approved to be vented either horizontally, through the side wall or vertically through the roof. You may vent through a Class A or masonry chimney if an approved adapter is used.

This appliance is a direct vent heater. All combustion air must come directly from the outside of the building. The vent pipe for this unit consists of an inner and an outer pipe. The inner pipe carries the appliance exhaust out of the system, and the outer pipe brings fresh combustion air into the appliance.

A round support box/wall thimble or heat shield is required when the venting passes through a combustible wall.

A support box or ceiling firestop is required when the venting passes through a ceiling.

Roof flashing and a storm collar are required when venting passes through the roof.

Follow instructions provided with the venting for installation of these items.

WARNING

Fire Hazard. Explosion Risk. Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney flue serving a separate solid-fuelor gas burning appliance.

Vent this appliance directly outside.

Use separate vent system for this appliance.

May impair safe operation of this appliance or other appliances connected to the flue.

B. Use of Elbows

CAUTION

ALL vent configuration specifications MUST be followed.

This product is tested and listed to these specifications.

Appliance performance will suffer if specifications are not followed.

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 5.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2(216 mm) inches horizontal run and8-1/2(216 mm) inches vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 5.1).

Vertical

 

 

in.

 

 

 

 

 

.

1/2

 

 

in

 

12

8-

 

 

8-1/2in.

Horizontal

Figure 5.1

C. Measuring Standards

Vertical and horizontal measurements were made using the following standards.

1.Pipe measurements are from center line to center line.

2.Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 4.1) on page 9.

3.Vertical terminations are measured to the top of the last pipe before termination cap.

4.Horizontal pipe installed level with 1/4 inch rise per foot.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

11

D. How to Use the Vent Graph

1.Measure the distance from the top of appliance to the center of the 90° elbow. On the graph below, draw a horizontal line from that measurement on the vertical axis across until it intersects with the slanted line.

2.From the point of this intersection, draw a vertical line to the bottom of the graph.

3.The point at which this line meets the bottom line of the graph is the maximum length of the horizontal run.

Example 1: If the vertical dimension from the top of the appliance to the center of the 90° elbow is 7 ft. (2 m), the horizontal run to the outer wall flange must not exceed 13 ft. (4 m).

Example 2: If the vertical dimension from the top of the appliance is 21 ft. (6.4 m), the horizontal run to the outer wall flange must not exceed 9 ft. (3 m).

4.Each 90° elbow is equivalent to 3 ft. (914 mm) of vent pipe and each 45° elbow is equivalent to 1 ft. (305

mm)of vent pipe, and must be subtracted from vent pipe run. A single vertical to horizontal 90° elbow is already calculated into the allowable 15 ft. (5 m) run. Each additional 90° elbow reduces the maximum horizontal distance by 3 ft. (914 mm).

Example: The use of three elbows would reduce the allowable horizontal run to 9 ft. (3 - 1 = 2 elbows x 3 ft. = 6 ft.; 15 ft. max. - 6 ft. = 9 ft. max.)

E. Venting Guidelines

The maximum horizontal vent run is 15 ft. (5 m) when the vertical vent rise is 10 ft. (3 m).

The minimum horizontal vent run is 11-5/8in. (295 mm).

Horizontal sections require a 1/4 in. (6 mm) rise for every 12 in. (305 mm) of horizontal travel.

Horizontal sections require noncombustible support every 3 ft. (914 mm), e.g. wall strap.

Wall thickness: Minimum 4 in. (102 mm). Maximum 20 in. (508 mm).

Vent Diameter: Exterior 6-5/8in. (168 mm); Inner 4 in. (102 mm).

EXCEPTION FOR REAR VENT KIT, HORIZONTAL INSTALLATION:

• The maximum horizontal vent run is 2 ft. (610 mm).

NOTICE: Maximum horizontal vent run is 18 in. (457 mm) when using the HRC termination cap.

The maximum horizontal vent run with a 45° elbow is 18 in. (457 mm).

No external minimum rise is required. The minimum horizontal vent run is 11-5/8in. (295 mm).

For any vertical rise when rear venting, a minimum of 2 ft. (610 mm) vertical must be used prior to any horizontal run.

 

35'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

34'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

32'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VENT

RESTRICTOR

 

 

 

 

 

 

 

 

 

 

 

 

 

24'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EX. 2

 

 

PLATE

REQUIRED

 

 

 

 

 

 

 

 

 

22'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VERTICAL DISTANCE

18'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOTAL HORIZONTAL RUN TO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUTSIDE OF EXTERIOR WALL

FROM APPLIANCE

14'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(INCLUDING ELBOWS)

TO THE 90º ELBOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To adjust the vent restrictor

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

plate, see page 34.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EX. 1

8'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0'

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11-5/8”2'

4'

6'

8'

10'

12'

14' 15'

(MIN)

 

 

 

 

 

 

 

 

(MAX)

6 ft. (2 m) Minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vertical Termination

 

 

 

 

 

 

 

2 ft. (610 mm) Maximum Horizontal run with no

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

vertical pipe and with 1/4 in. (6 mm) rise per foot.

 

 

 

 

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

 

 

 

CL For rear vent or top

 

 

 

 

 

 

 

 

 

 

 

of appliance for top

6 in. (152 mm) Minimum starter pipe

 

 

vent.

 

 

 

 

 

 

 

 

 

 

 

Figure 5.2

 

 

 

 

 

 

 

 

 

 

 

12

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

F. Horizontal Termination

TERMINATION CAP

90º ELBOW

PIPE LENGTH

WALL THIMBLE

WALL THIMBLE COVER

PIPE LENGTH

CHOOSE BETWEEN

SLIM LINE

OR

STANDARD

WALL THIMBLE

WALL THIMBLE

INTERIOR WALL

 

TERMINATION CAP

 

 

- 2 IN. (51 MM)

 

 

CLEARANCE FROM

 

 

REAR OF STOVE

 

 

CENTER LINE

 

 

 

MINIMUM OF 6 IN. (152 MM) OF

 

 

PIPE THROUGH THE WALL

TRIM RING

 

Figure 5.3

1.Determine the desired location of the appliance. Check to ensure that wall studs or roof rafters are not in the way when the venting system is being planned. If this is the case, you may want to adjust the location of the appliance.

WARNING

Fire Risk

Exhaust Fumes Risk

Impaired Performance of Appliance

Ensure vent components are locked together correctly.

Pipe may separate if not properly joined.

2.Direct vent pipe is designed with a locking connection. To connect the venting system to the appliance flue outlet, a twist-lockadapter is built into the appliance at the factory. Wall thickness may vary. Remember to include wall thickness in minimum clearances when figuring venting lengths for your installation needs.

3.Female ends of direct vent pipe/elbows are designed to slide straight onto the male ends of adjacent pipes by orienting the pipe indentations so they match and slide into the entry slots on the male ends, see Figure 5.4. Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 10.5. Continue adding vent components, locking each succeeding component into place. Ensure that each succeeding vent component is securely fitted and locked into the preceding component.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 5.4 Adding Venting Components

WARNING

Fire Risk. Explosion Risk.

Combustion Fume Risk.

Use vent run supports per installation instructions.

Connect vent sections per installation instructions.

Maintain all clearances to combustibles.

Do NOT allow vent to sag below connection point to appliance.

Maintain specified slope (if required).

Improper support may allow vent to sag or separate.

4.For installations using a round support box/wall thimble (check pipe manufacturer's instructions), mark the wall for a 10 in. x 10 in. (254 mm x 254 mm) square hole. The center of the square hole should line up with the center line of the horizontal pipe, as shown in Figure 5.5. Cut and frame the hole in the exterior wall where the vent will be terminated. If the wall being penetrated is constructed of noncombustible material, i.e. masonry block or concrete, a 7 in. (178 mm) diameter hole is acceptable.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

13

 

CENTER OF HOLE

CENTER LINE

 

WALL

CENTER LINE

THIMBLE

 

Figure 5.5

5.Installation requires a minimum of 6 in. (152 mm) horizontal run of vent with a 1/4 in. (6 mm) rise run towards the termination. Each 1 ft. (305 mm) of horizontal venting must include a 1/4 in. (6 mm) rise. Never allow the vent to run downward. This could cause high temperatures and may present the possibility of a fire. The location of the horizontal vent termination on an exterior wall must meet all local and national building codes, and must not be easily blocked or obstructed, see Figure 4.4 on page 10.

6.For installations requiring a vertical rise on the exterior of the building, the HHT RHVK snorkel kit (Part #8448921) is available with a 14 in. (356 mm) and a 36 in. (914 mm) tall snorkel termination cap. Follow the same installation procedures as used for standard horizontal terminations. If the snorkel termination must be installed below grade (i.e. basement application), proper drainage must be provided to prevent water from entering the snorkel termination. Do not backfill around snorkel termination.

7.Position the horizontal termination cap in the center of the 10 in. x 10 in. (254 mm x 254 mm) square hole and run a bead of non-hardeningmastic around its outside edges, so as to make a seal between it and the wall, attach termination cap to the exterior wall with the four wood screws provided. The arrow on the vent cap should be pointing up (Figure 5.6).

WOOD

SCREW

HOT

PART HHW2 #841-0670

(PREFERRED)

WALL THIMBLE

Figure 5.6

8.The four wood screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

9.Termination cap HHW2 (Part #841-0670)is highly recommended on a building with vinyl siding, as the vinyl siding standoff is built in. The pilot hole will be 2 in. (51 mm) closer to the bottom of the square than the top. Using a framing square, draw a 14 in. x 14 in. (356 mm x 356 mm) square around the pilot hole. See Figure 5.7.

8 in.

7 in.

(203 mm)

(178 mm)

7 in.

6 in.

(178 mm)

(152 mm)

Figure 5.7

10.If you are installing termination cap HHW2, the pipe will be off center on flashing). Ensure that proper clearances to combustible materials are maintained. If you are using an approved termination cap other than HHW2 (part #841-0670)on a building with vinyl siding, a vinyl siding standoff should be installed between the termination cap and the exterior wall (Figure 5.8, on the next page). Follow manufacturer’s instructions for attaching the vinyl siding standoff to the horizontal termination cap. The vinyl siding standoff prevents excessive heat from possibly melting the vinyl siding material. The vent terminal cap shall not be recessed into a wall or siding. Remove siding from the area where the standoff will be located.

14

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

 

VINYL SIDING

 

APPLY SEALANT TO

 

ALL FOUR SIDES

 

SCREWS

 

BOLT HORIZONTAL TOP

 

TO VINYL STANDOFF

 

SCREWS

WALL

 

THIMBLE

VINYL SIDING STANDOFF WITH

COVER

SIDING BENEATH REMOVED

 

WALL THIMBLE

Figure 5.8

11.Place the wall thimble cover over the pipe assembly and slide the appliance and vent assembly towards the wall, carefully inserting the vent pipe into the vent termination cap assembly. It is important that the vent pipe extend into the vent termination cap a sufficient distance so as to result in a minimum pipe overlap of 1-1/4in. (32 mm). Secure the connection between the vent pipe and the vent termination cap by attaching the two sheet metal strips extending from the vent termination cap assembly into the outer wall of the vent pipe. Use the two sheet metal screws provided to connect the strips to the pipe section (Figure 5.9).

1/4 in. (6 mm)

FOLD STRAP

HERE

SHEET METAL

SCREW

 

WALL

WALL THIMBLE COVER/CEILING

THIMBLE

 

FIRESTOP AS REQUIRED BY

 

LOCAL JURISDICTION

STRAP

 

Figure 5.9

Note: The attachment from the vent pipe to the vent termination cap must be sealed with silicone. Termination caps shall not be recessed into a wall or siding.

WARNING

Fire Risk

Exhaust Fumes Risk

Impaired Performance of Appliance

Ensure vent components are locked together correctly.

Pipe may separate if not properly joined.

WARNING

Do NOT connect a pipe section to a termination cap without using the telescoping flue section found on the termination cap.

WARNING

Burn Risk

• Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

15

G. Vertical Termination

VERTICAL TERMINATION CAP

STORM COLLAR

FLASHING

FIRESTOP

SUPPORT BOX

PIPE LENGTH

Figure 5.10

1.Check the installation instructions for required 1 in. (25 mm) clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. Check the instructions for maximum vertical rise of the venting system, and any maximum horizontal offset limitations. All offsets must fall within the set parameters of the vent graph (Figure 5.2) located on page 12.

Note: Maximum vertical rise allowable is 40 ft. (10.7 m), Figure 5.11. Maximum number of 45º elbows permitted for a vertical installation is eight, provided their installation does not decrease maximum allowable horizontal run (as specified by vent graph, on page 12).

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

40 ft. (12 m) MAXIMUM

Figure 5.11

2.Set the gas appliance in its desired location. Drop a plumb bob down from the ceiling to the position of the appliance flue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, and mark the spot where the vent will penetrate the roof. Determine if ceiling joists, roof rafters, or other framing will obstruct the venting system. You may wish to relocate the appliance, or to offset, as shown inFigure 5.12 to avoid cutting load bearing members.

PLUMBER'S TAPE

CONNECTED TO

WALL STRAP

WALL

STRAP

TWO 45º

ELBOWS

Figure 5.12

16

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

3. To install the round support box/wall thimble cover in

 

 

a flat ceiling, cut a 10 in. (254 mm) square hole in the

 

 

ceiling, centered on the hole drilled in Step 2. Frame

 

 

the hole as shown in Figure 5.13.

SHINGLES OVERLAP ON

CAP AND STORM

 

TOP EDGE OF FLASHING

 

 

COLLAR NOT SHOWN

 

 

FOR CLARITY

CEILING JOISTS

 

 

FRAMING

 

 

ROUND CEILING

SUPPORT BOX/WALL

THIMBLE COVER

Figure 5.14

 

1-1/2in. (38 mm)

 

7.

Continue to assemble pipe sections until the height of

 

LONG WOOD

 

 

SCREWS

 

 

the vent (before adding the termination cap) meets the

 

Figure 5.13

 

 

 

minimum code requirements as outlined in the current

 

 

 

 

 

CAN/CGA-B149Installation Codes (in Canada), the

4. Assemble the desired lengths of

pipe and elbows

 

National Fuel Gas Code NFPA 54/ANSI Z223.1 (in

 

USA), or local codes. Note that for steep roof pitches,

 

necessary to reach from the appliance up through

 

the vent height must be increased.

See Roof Pitch

 

the round support box. Ensure that all pipe and elbow

 

Table (Figure 4.2, on page 9). In high wind conditions,

 

connections are in their fully twist-lockedposition.

 

nearby trees adjoining rooflines, steep pitched roofs,

 

Assemble as instructed.

 

 

 

and other similar factors can result in poor draft, or

5.

Cut a hole in the roof centered on the small drill hole

 

down drafting. In these cases increasing the vent

 

placed in the roof in Step 2. The hole should be of

 

height or switching to the high wind termination cap

 

sufficient size to meet the minimum requirements for

 

may solve this problem.

 

 

clearance to combustibles, as specified.

Continue

8.

Slip the storm collar over the pipe, and push it down

 

to assemble lengths of pipe and elbows necessary

 

to the top of the flashing (Figure 5.15). Use non-

 

to reach from the ceiling support box/wall thimble up

 

hardening sealant above and below the joint between

 

through the roof line. Galvanized pipe and elbows may

 

the storm collar and the pipe.

 

 

be utilized in the attic, as well as above the roofline.

 

 

 

 

The galvanized finish is desirable above the roofline,

 

 

 

 

due to its higher corrosion resistance.

 

 

 

 

 

• If an offset is necessary in the attic to avoid

 

 

 

 

obstructions, it is important to support the vent pipe

 

OPTIONAL HIGH WIND

 

 

every 3 ft. (914 mm) to avoid excessive stress on the

 

TERMINATION CAP

 

 

 

SECURE FLASHING WITH

 

 

elbows, and possible separation.

Wall straps are

 

 

 

available for this purpose, Figure 5.12, page 16.

 

NON-HARDENINGSEALANT AND

 

 

 

ROOFING NAILS

 

 

• Whenever possible, use 45° elbows, instead of 90°

 

 

 

 

elbows. The 45° elbow offers less restriction to the

 

 

 

 

flow of flue gases and intake air.

 

 

 

 

 

6. Slip the flashing over the pipe section(s) protruding

 

 

 

 

through the roof. Secure the base of the flashing to

 

 

 

 

the roof with roofing nails. Ensure the roofing material

 

 

 

 

overlaps the top edge of the flashing as shown in

 

 

 

 

Figure 5.14. Verify that the chimney is the required

 

 

 

 

height above the roof. See roof pitch table, Figure 4.2,

 

 

 

 

on page 9.

 

 

 

 

 

 

 

 

 

Figure 5.15

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

17

9. Twist-lockthe vent cap and seal.

Note: Formulti-storyvertical installations, a ceiling firestop is required at the second floor, and any subsequent floors (Figure 5.16). The opening should be framed to 10 in. x 10 in. (254 mm x 254 mm) inside dimensions, in the same manner as shown in Figure 5.13.

NAILS

CEILING FIRESTOP

MINIMUM 1 in.(25 mm)

CLEARANCE

MINIMUM 1 in.(25 mm)

CLEARANCE

MINIMUM 1 in. (25 mm)

CLEARANCE

MINIMUM 1 in.(25 mm)

CLEARANCE

Figure 5.16

WARNING

Fire Risk. Explosion Risk.

• Any occupied areas above the first floor, including closets and storage spaces, which the vertical vent passed through must be enclosed. The enclosure may be framed and sheetrocked with standard construction materials; however, refer to these installation instructions for the minimum allowable clearance between the outside of the vent pipe and the combustible surfaces of the enclosure. Do not fill any of the required air space with insulation.

H. Secure the Vent Sections

Vertical runs of SLP pipe must be supported every 8 ft. (2.44 m).

Horizontal sections must be supported every 5 feet (1.52 m).

Vent supports or plumbers strap (spaced 120º apart) may be used to support vent sections. See Figures 10.8 and 10.9.

Wall shield firestops may be used to provide horizontal support to vent sections.

SLP ceiling firestops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

120º

Figure 10.8 Securing Vertical Pipe Sections

120º

Figure 10.9 Securing Horizontal Pipe Sections

18

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

I. Disassemble Vent Sections

Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.11.

Pull carefully to separate the pieces of pipe.

Figure 10.10 Rotate Seams for Disassembly

Figure 10.11 Align and Disassemble Vent Sections

J. Cathedral Ceiling

1.Follow installation Steps 1 and 2 under vertical installation section, page 16.

2.Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

3.Lower the support box through the hole in the roof until the bottom of the support box protrudes at least 2 in. (51 mm) below the ceiling (Figure 5.17). Align the support box both vertically and horizontally with a level. Temporarily tack the support box in place through the inside walls and into the roof sheathing.

LEVEL

CATHEDRAL CEILING

SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm)

GREATER IN SIZE THAN

PATTERN OF SUPPORT

BOX AS IT IS PROJECTED

ONTO ROOF LINE

Figure 5.17

4.Using tin snips, cut the support box from the top corners down to the roofline, and fold the resulting flaps over the roof sheathing (Figure 5.18). Before nailing it to the roof, run a bead ofnon-hardeningmastic around the top edges of the support box to make a seal between it and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

5.Assemble the desired lengths of pipe and elbows necessary to reach from the appliance up through the round support box. Ensure that all pipe and elbow connections are in their fully twist-lockedposition. Assemble as instructed.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

19

Figure 5.18

6.Place the support clamp (provided with the support box) inside the support box (at the bottom), and secure to the pipe section. The clamp allows the support box to support the weight of the pipe sections. Continue to add pipe sections until you are above the roofline.

7.Complete the cathedral ceiling installation by following the same procedures outlined in steps 7 through 9 for vertical installations, pages 17-18.

8.Install the black trim collar around the outside of the cathedral ceiling support box (Figure 5.19). The two pieces of the trim collar slide over one another to allow for easy adjustment around the support box. Using the six screws provided, secure the four corners and the overlapping sections of the trim collar to the ceiling. You may want to predrill the holes for the overlapped sections for ease of installation.

TRIM COLLAR

CATHEDRAL CEILING

SUPPORT BOX

SCREWS

Figure 5.19

K. Class A Metal Chimney

TERMINATION

CAP PART #SLK-991DA

TOP ADAPTER

FLASHING

EXISTING METAL

CHIMNEY SYSTEM

4 in. (102 mm) FLEX PIPE

RETRO CONNECTOR

DIRECT VENT

PIPE

Figure 5.20

CAUTION

Ensure that existing chimney is functionally sound and clean.

Have inspection done by qualified chimney sweep or professional installer BEFORE converting to direct vent appliance.

1.Remove existing chimney cap.

2.Measure the distance from the top of the chimney to the bottom of the ceiling support box, add 3 in. (76

mm)to this measurement, and cut a section of 4 in. (101 mm) flex pipe to that length (the flex should be fully extended).

3.Connect the end of the flex pipe section to the underside of the top adapter, using four sheet metal screws (Figure 5.21).

TOP ADAPTER

FLEX PIPE

SHEET METAL SCREWS

Figure 5.21

20

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

4.Pass the flex pipe down through the center of the chimney system, and center the top adapter on the top of the chimney pipe. Drill four 1/8 in. (3 mm) diameter holes through the top adapter, and into the chimney top. Ensure that you are drilling into the metal on the chimney. Twist lock the high wind termination cap onto the top adapter (Figures 5.22 and 5.23).

L. Existing Masonry Chimney

Type A

CHIMNEY LINER

TERMINATION CAP PART #923GK

3 IN. (76 MM) FLEX LINER

CO-AXIALTOCO-LINEAR

CONNECTOR PART #923GCL

PIPE LENGTH (OPTIONAL)

SHOWING TWO 30 FT. (9 M) SECTIONS OF FLEX LINER

Figure 5.22

HIGH WIND

TERMINATION CAP

SHEET METAL SCREWS

DRILL FOUR 1/8 IN. (3 MM)

DIAMETER HOLES

Figure 5.23

5.Pull the flex pipe down through the ceiling support box, until it protrudes approximately 3 in. (76 mm). Connect the flex pipe to the retro connector, and attach with sheet metal screws.

6.Push the flex pipe back up into the ceiling support box, center the retro connector, and attach it to the support box with sheet metal screws.

7.The connection between the appliance and the retro connector may be completed with sections of direct vent pipe.

Type C - Up & Out Installation

*NOTE: In the Commonwealth of Massachusetts, the word damper shall be replaced with the words flue restrictor.

Figure 5.24

CAUTION

Ensure that existing chimney is functionally sound and clean.

Have inspection done by qualified chimney sweep or professional installer BEFORE converting to direct vent appliance.

1.Before cutting any holes, assemble the desired sections of direct vent pipe to determine the center of the masonry penetration.

2.Once the center point of the penetration has been determined, cut a 6 in. (152 mm) diameter hole in the masonry. If the hole is too large, the retro connector might not mount properly; if the hole is too small, the appliance might starve for intake air. If there is a frame wall in front of the masonry wall, cut and frame a 10 in. (254 mm) square opening in the wall (centered around the 6 in. (152 mm) masonry opening). If there is sheet rock only (no studs) in front of the masonry the 10 in. (254 mm) opening is still needed, but does not need to be framed. If the hole is framed a round support box/wall thimble is required. This allows the retro connector to mount directly on the masonry and provide the correct clearances to combustibles (Figure 5.25).

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

21

STUDWALL

10 in. x 10 in.

(254 mm x 254 mm)

FRAMED OPENING IN WALL

MASONRY

CHIMNEY

RETRO

CONNECTOR

FOUR MASONRY BOLTS

WALL THIMBLE COVER

(NOT INCLUDED)

 

NOTE: For hearth applications refer to page 20, Figure 5.24 for the use of the 923GCL co-axialtoco-linearappliance connector.

Figure 5.25

3.Secure the flashing to the top of the masonry chimney using a bead of non-hardeningsealant-adhesive.If the flashing is larger than the top of the chimney, cut and fold flashing as needed to fit chimney (Figure 5.26).

CUT AND BEND FLASHING

AS NEEDED TO FIT CHIMNEY

SEALANT-ADHESIVE

Figure 5.26

4.To determine the length of flex needed, measure from 3 in. (76 mm) above the top of the flashing down to the level of the opening. Add the distance from the center of the chimney out through the wall. Cut a piece of 4 in. (102 mm) flex to this length (extended to its nominal length). Be sure to leave 2-3in.(51-76mm) of flex above the existing chimney to allow for connection to the termination kit.

5.Connect the flex liner to the top adapter using four sheet metal screws (Figure 5.21).

6.Feed the flex liner through the flashing into the chimney. Carefully feed the flex liner down the chimney to the bottom and out the opening in the masonry wall, forming an angle to line up the flex liner with the vent opening on the appliance.

WARNING

Fire Risk. Explosion Risk.

Do not let the flex liner sag below the level at which it will connect to the appliance or connector. This could allow hot gas to become trapped and potentially become a fire hazard. The flex liner path should always be sloped up toward the termination cap.

7.If additional lengths of flex liner are needed to span the chimney height, use a flex coupler to connect the pieces of flex liner together. Connect the flex to the coupler by using four sheet metal screws for each side (Figure 5.27).

FLEX LINER

FLEX COUPLER

SHEET METAL SCREWS

Figure 5.27

8.Secure the top adapter to the flashing. Use three sheet metal screws through the side of the top adapter into the flange on the flashing (Figure 5.28). Twist lock the high wind termination cap on to the top adapter.

22

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

HIGH WIND TERMINATION

CAP #SLK-991DA

TOP ADAPTOR

THREE SHEET

METAL SCREWS

FLASHING

Figure 5.28

9.Attach the flex to the retro connector. Use three sheet metal screws to attach the flex liner to the connector (Figure 5.29). Mount the retro connector to the masonry wall using masonry bolts. Redrill larger holes on connector as needed. Be careful to ensure that the connector is centered in the opening and the mounting holes line up with the masonry wall.

6 in. (152 mm) DIAMETER OPENING IN MASONRY WALL

10.Slide wall thimble cover over retro connector and secure with masonry bolts (Figure 5.30). If you have a framed wall in front of the masonry, use wood screws to mount wall thimble cover to framed wall, over retro connector and 10 in. (254 mm) square framed opening (Figure 5.25). If needed, add a section of direct vent pipe to the retro connector in order to extend through the opening in the wall thimble cover.

RETRO

CONNECTOR

WALL

THIMBLE COVER

FOUR MASONRY BOLTS

(NOT INCLUDED)

Figure 5.30

11.The connection between the appliance and the retro connector may be completed with sections of direct vent pipe.

RETRO

CONNECTOR

THREE MASONRY BOLTS

(NOT INCLUDED)

Figure 5.29

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

23

M. Slim Line Wall Thimble

Before you begin, review the venting configurations in Figures A, B and C on the next page.

Assembling Slim Line Trim Ring and Heat Shield

Figure 5.31 Lay the trim ring on flat surface and bend up the six welded brackets into a 90 degree position. The brackets along the outer edge of the ring are for locating the ring in the center of the hole.

Figure 5.32 The heat shield is shipped flat and must be hand bent into a half circle before attaching it to the trim ring. Bend the heat shield as shown.

CAUTION! Risk of Cuts. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Figure 5.33 Attach the heat shield to the trim ring with the four screws provided. Screws go through the heat shield and into the brackets on the trim ring.

Installing Slim Line Trim Ring and Heat Shield

Measure from the floor to the center of the vent pipe. Cut out a 9-1/2in. (241 mm) hole in the wall. Hold the trim ring/heat shield assembly in place and put a mark on the shield with a black marker where it protrudes through the exterior wall. SeeFigure A on the next page.

Use that mark as a guide to trim off excess heat shield with a pair of sheet metal shears.

3/4

3/4

3/4

Figure 5.34 When installing the trim ring/heat shield assembly make sure the trim ring is centered in the hole and that the shield is above the pipe. There must be a minimum of 3/4 in. (19 mm) minimum clearance maintained to combustibles from the top of the heat shield.

Ensure that framing on the inside of the wall is a minimum inner framing diameter of 10 in. x 10. in. (254 mm x 254 mm).

The four trim ring mounting screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

24

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

FIG. A 90 DEGREE ELBOW

USE HEAT SHIELD / WALL THIMBLE

PLACE MARK WHERE PROTRUDES THROUGH

EXTERIOR WALL TO CUT OFF EXCESS

90° ELBOW

CENTER LINE

 

 

 

 

 

 

 

PIPE LENGTH

 

 

 

 

 

 

 

TRIM RING

PIPE LENGTH

 

 

 

HTI VENT HHW2 PART #841-0670

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(RECOMMENDED FOR OPTIMUM PERFORMANCE)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIG. B 45 DEGREE ELBOW

TRIM RING

HEAT SHIELD

OVER PIPE

45° ELBOW

5 IN. (127 MM) CLEARANCE FROM APPLIANCE CORNER TO COMBUSTIBLE WALL

5 IN. (127 MM) CLEARANCE FROM APPLIANCE CORNER

FIG. C MINIMUM CLEARANCE

INTERIOR WALL - 2 IN. (51

MM) CLEARANCE FROM

REAR OF STOVE

CENTER LINE

MINIMUM OF 6 IN. (152 MM)

OF PIPE THROUGH THE WALL

WALL THIMBLE

 

 

 

 

 

 

 

 

 

HTI VENT HHW2 PART

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HEAT SHIELD OVER

 

#841-0670(RECOMMENDED

 

TOP HALF OF PIPE

 

FOR OPTIMUM PERFORMANCE)

TRIM RING

Figure 5.35

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

25

6 Gas Information

A. Fuel Conversion

Make sure the appliance is compatible with available gas types.

Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressures

Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA54.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressures must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 inches

11.0 inches

w.c.

w.c.

 

Maximum inlet gas pressure

7.0 inches

14.0 inches

w.c.

w.c.

 

Manifold pressure

3.5 inches

10.0 inches

w.c.

w.c.

 

If the pressure is not sufficient, ensure:

The piping used is large enough.

The supply regulator is adequately adjusted.

That the total gas load for the residence does not exceed the amount supplied.

The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should supply gas at the suggested input pressure listed above. Contact the local gas supplier if the regulator is at an improper pressure.

26

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

C. Gas Connection

Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

WARNING

Gas Leak Risk

Support control when attaching pipe to prevent bending gas line.

Note: The gap between supply piping and gas access hole may be caulked withcaulk with a minimum of 300ºF continuous exposure rating or stuffed withnon-combustible,unfaced insulation to prevent cold air infiltration.

Leak test all gas line joints and the gas control valve prior to and after starting the appliance.

Before making the gas connection, ensure that the appliance you are installing is designed for the type of gas being supplied. This information can be found on the ratings label under the appliance. If the appliance has been converted to propane (LP), the valve cover should have a label stating that the appliance has been converted to propane.

Connect the gas line at the 3/8 in. (10 mm) pipe connector on the valve at the back of appliance. We recommend connecting the appliance with an approved flex gas line. If flex gas lines are not approved in your area, you must connect a hard pipe to the gas hookup.

You must supply a manual shut-offvalve in a visible location within 3 ft. (914 mm) of the appliance.

WARNING

Fire or Explosion Hazard

Gas buildup during line purge may ignite.

Purge should be performed by qualified technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

Air only needs to be purged again if gas valve has been turned to the OFF position.

WARNING

CHECK FOR GAS LEAKS

Explosion Risk

Fire Risk

Asphyxiation Risk

Check all fittings and connections.

Do not use open flame.

After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially-available,non-corrosiveleak check solution. Be sure

to rinse off all leak check solution following testing.

Fittings and connections may have loosened during shipping and handling.

WARNING

Fire hazard.

Do NOT change the valve settings.

• This valve has been preset at the factory.

• Changing valve settings may result in fire hazard or bodily injury.

HIGH ALTITUDE INSTALLATIONS

Omni-TestLaboratories, Inc. listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and 0 to 4500 feet in Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

27

7 Electrical Information

A. Recommendation for Wire

See Figure 7.1 for recommended maximum lead length (two wire) when using wall thermostat/switch.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

6.Keep wire lengths as short as possible by removing any excess wire length.

7.Low voltage and 110 VAC voltage cannot be shared within the same wall box.

8.Ensure the thermostat is mounted level for accurate readings.

9.The thermostat should be mounted on an inside wall and not in direct line with the appliance convection air.

10.If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home.

Do not connect this appliance to a thermostat serving any other appliance.

B. Connecting to the Appliance

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

1.This appliance may be used with a wall switch, wall mounted thermostat and / or a remote control

Bedroom installation in Canada requires this appliance to be connected to a thermostat.

WARNING

Shock hazard.

This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle. Do not cut or remove the grounding prong from this plug.

2.If using thermostat, use one compatible with a millivolt gas valve system.

3.Follow parameters for locating thermostat (see individual thermostat instructions) to ensure proper operation of appliance.

4.Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.

5.Use the following chart for wire sizing.

Wire Size

Max. Length

16 gauge

65 feet

18 gauge

40 feet

20 gauge

25 feet

22 gauge

18 feet

Figure 7.1

C. IntelliFire® Ignition System Wiring

This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 7.2 on the next page.

This appliance is equipped with an IntelliFire® control valve which operates on a 3 volt system.

This appliance is supplied with a 3 volt AC transformer, which requires the installation of the supplied junction box.

This appliance is supplied with a battery pack that requires two D cell batteries (not included). Batteries cannot be placed in the battery pack while using the 3 volt AC transformer. Conversely, the transformer must be unplugged if the battery pack is used.

NOTICE: Battery polarity must be correct or module damage will occur.

28

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

 

 

 

 

IGNITION MODULE

 

 

 

 

 

3 VAC

I

 

 

PLUG-IN3V

 

 

 

INTERMITTENT

 

 

 

 

 

 

TRANSFORMER

 

FLAME

 

 

PILOT IGNITOR

 

 

 

 

S

 

ON/OFF

 

SPARKER/SENSOR

 

 

WALL

 

 

 

 

 

SWITCH

 

 

 

 

 

 

IGNITION

 

 

 

 

 

 

MODULE

 

 

 

 

 

 

(3V)

 

 

 

 

 

 

 

 

 

 

WHT

 

 

 

 

BATTERY

BLACK

ORG

 

 

VALVE

 

 

 

 

 

PACK

GROUND TO

 

 

 

 

 

 

 

 

 

 

APPLIANCE CHASSIS

 

 

 

REMOTE

 

RED

*

 

 

 

HOT

 

 

NEUTRAL

GROUND

CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

BRN

BRN

 

 

 

 

 

 

ORG

GRN

 

 

 

 

 

 

 

 

 

 

PIGGYBACK

 

 

 

 

TRANSFORMER

ON/OFF SWITCH

 

 

 

 

 

 

 

 

 

 

3 VAC

 

 

 

 

 

 

PLUG IN

 

 

 

 

JUNCTION BOX

 

 

VALVE

 

 

 

 

 

 

NOTE: Appliance will not operate unless properly grounded.

Figure 7.2

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING

Shock hazard.

Replace damaged wire with type 105º C rated wire.

Wire must have high temperature insulation.

D. Loss of Power and Battery Backup Usage

1.

Disconnect the power supply.

 

Unplug when

 

2.

Remove the front door assembly and lower access

 

using batteries

 

 

panel.

 

 

 

 

 

 

3.

Place two "D" cell batteries into the battery

holder.

 

 

 

(Figure 7.3)

 

 

 

4.

Turn on appliance and verify it is operational.

 

 

 

5.

Replace lower access panel and front door assembly.

 

 

 

CAUTION

 

 

 

If IPI battery back-upis installed:

 

 

 

• Do not install batteries if the backup mode may not be used

 

 

 

for extended time.

 

 

 

Batteries may leak.

 

 

 

Install batteries only when needed for power outage.

 

 

 

 

 

BATTERY LOCATION

 

 

 

 

Figure 7.3

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

29

E. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 7.4):

The power supply for the appliance must be brought into a switch box.

The power can then be supplied from the switch box to the appliance using a minimum of 14-3with ground wire.

At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

Add a 1/4 inch insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 inch male) as shown.

 

SWITCH

MINIMUM 14-3AWG

 

WITH GROUND

 

Red

Black

Black

White

White

Green

Green

JUNCTION BOX

 

Red Black White Green

 

 

POWER

 

SUPPLY WIRES

 

SWITCH BOX

Red

 

Figure 7.4 Junction Box Wired to Wall Switch

 

30

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

8 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

Gas line and power cord are shipped inside back panel. To access the gas line and power cord, remove the top plate from the appliance. Remove and retain the two Allen head screws that hold the back panel in place. Refer to Figure 8.8.

Using the black grommet located in the component bag, slide it into the bottom of the back panel and feed the power cord through the grommet, as shown in Figure 8.1.

B. Unbolting Appliance from the Pallet

The appliance is bolted and screwed to the pallet for shipping. Use a 1/2 in. socket to remove the bolt in center of bottom plate. Use a Phillips screwdriver to remove the two screws in the front of the bottom plate and the two screws holding the metal strap across the back of the appliance. Refer to Figure 8.2 for locations.

Figure 8.2

Figure 8.1

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

31

C. Leveling and Lagging Down the Appliance

Lagging the appliance down is REQUIRED.

WARNING

Fire Risk.

Odor Risk.

Tipping Risk

Install gas stove on a stable, level platform/ floor strong enough to support gas stove without tipping.

USE wood flooring, ceramic tile, brick hearth or high pressure laminate flooring applied

directly over the sub-flooringmaterial.

Level

Securing holes

Level

screw

Lag bolt hole

screw

 

 

Figure 8.3

Figure 8.4

After unbolting the appliance from the pallet, insert two 1/4 20 x 1/1/2 counterscrews.

Using pliers, adjust the counterscrews to level the appliance.

LAGGING

CLEARANCE

HOLE

Figure 8.5

Place the lag bolt from the component bag in the center hole in the bottom plate (lagging clearance hole). The appliance must be lagged down securely to prevent tipping forward.

Figure 8.6

Using pliers, adjust the counterscrews to level the appliance.

D. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 12.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listedaccessories voids warranty.

Using non-listedaccessories may result in a safety hazard.

Only Hearth & Home Technologies approved

accessories may be used safely.

32

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

E. Top to Rear Vent Conversion

Kit Contents: Top cover (no hole); Back panel (with hole).

Tools Required: Power drill; #2 Phillips bit; 5/32 in. (4 mm) Allen wrench; 5/8 in. (16 mm) open end wrench;high-tempsilicone sealant (optional).

1.Remove the front door assembly by lifting it off of the spring-loadedlatches on top of the appliance. Remove the inner glass door by disengaging thespring-loadedlatches at the bottom of the appliance and lifting it off of the two spring loaded latches at the top of the appliance.

2.Remove the top plate with hole and discard. (Figure 8.7).

INNER EXTENSION COLLAR

DV ADAPTER

Figure 8.9

6. Remove the four screws from the cover plate on rear of appliance. Retain cover plate, gasket and screws. (see Figure 8.10).

Figure 8.7

3.Remove and retain the Allen head screws that hold the solid back panel in place. (Figure 8.8) Remove and

discard the solid back panel.

Figure 8.10

ALLENHEAD SCREWS

Figure 8.8

4.Remove the four screws from the DV adapter collar. (Figure 8.9) Set aside DV adapter collar, gasket and screws.

5.Remove the inner extension starter collar (Shown in Figure 8.9) and set aside.

7.Install the outer collar with gasket to the rear of appliance with screws previously removed. Install the inner extension starter collar. (Figure 8.11).

8.Install the new back panel (with hole) to the rear of appliance. Replace the allen head screws removed in Step 3 to hold the back panel in place. (Figure 8.11).

Figure 8.11

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

33

9.Install the cover plate and gasket removed from the rear of the appliance to the top of the appliance with the screws previously removed. (Figure 8.12).

10.Install the new solid top.

Figure 8.12

F. Shutter Adjustment

The shutter is located on the underside of the burner, on the burner neck (see Figure 8.13).

Figure 8.13

Air Shutter Settings

PALOMA-BZ-MOD

 

 

PALOMA-GR-MOD

NG

LP

PALOMA-GYMOD

 

 

Rear Vent

1/2 in.

1/2 in.

Top Vent

3/8 in.

1/2 in.

G. Installing the Vent Restrictor

The vent restrictor plate must be installed before installing the baffle.

On the top of inside firebox for top vent ,on back of firebox for rear vent, loosen the three screws out about 1/8 in.

Place the vent restrictor plate over the the screws and slide into locking position. Retighten the screws. (See Figure 8.15.)

Top Vent

Rear Vent

Figure 8.15

For vertical venting above 15 ft. a vent restrictor is required.

34

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

H. Installing Rock Media and Ember Material

CAUTION! Risk of Cuts or Abrasions. Wear protective gloves and safety glasses during installation.

REAR ROCK

CLUSTER

NOTCHES ON

REAR ROCK

CLUSTER

LEFT ROCK

RIGHT ROCK

CLUSTER

CLUSTER

Figure 1. Rock Kit Components

KIT CONTENTS

(1) Rear Rock Cluster

(1) Left Rock Cluster

(1) Right Rock Cluster

(1 ) Bag Ember Material

INSTALLATION

1.Place the rear rock cluster in the firebox as shown in Figure 2. The flat portion should fit tight against the back of the firebox. Slide cluster to the right. There are notches on the bottom of the rock cluster that should fit over the base pan. Cluster should rest on burner and base pan.

NOTCHES ON

REAR ROCK

CLUSTER

Figure 2. Placing Rear Rock Cluster

2.Place right rock cluster in firebox as shown in Figure 3. The right end of the cluster should touch the right wall of the firebox. Push cluster back until the rear and right rock clusters touch as shown in Figure 4. Ensure the rock clusters are not covering any burner ports.

WARNING

Delayed Ignition Risk

Place rock clusters according to instructions.

Do NOT place rock clusters in a position that they cover burner ports.

Do NOT use any media other than the rock clusters supplied with this fireplace.

Fireplace will not function properly.

Delayed ignition may occur.

RIGHT ROCK

CLUSTER

Figure 3. Placing Right Rock Cluster

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

35

REAR ROCK

RIGHT AND REAR CLUSTERS

MAKE CONTACT

CLUSTER

RIGHT ROCK

 

 

CLUSTER

 

 

Figure 4. Right and Rear Rock Clusters Make Contact

3.Place left rock cluster in firebox as shown in Figure 5. The left end of the cluster should touch the left wall of the firebox. Push cluster back until the rear and left rock clusters contact each other as shown in Figure 6. Ensure the rock clusters are not covering any burner ports.

WARNING! Risk of Explosion! Follow instructions for placing rock clusters. DO NOT allow rock cluster to cover burner ports. Improperly placed rock cluster will interfere with proper burner operation.

LEFT ROCK

CLUSTER

Figure 5. Placing Left Rock Cluster

 

LEFT AND REAR

 

LEFT ROCK

CLUSTERS MAKE

REAR ROCK

CONTACT

CLUSTER

CLUSTER

 

 

Figure 6. Left and Rear Rock Clusters Make Contact

4.Ember material is shipped with this kit. To place the ember material:

WARNING! Risk of Explosion! Follow ember placement instructions. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation.

Embers CANNOT be placed directly over ports. Care should be taken not to cover the lighting trail of ports (from back to front).

Place dime-sizepieces of embers in the areas highlighted in Figure 7. Care should be taken so that the ports are not covered. Failure to follow this procedure will likely cause lighting and sooting problems.

EMBERS

Figure 7. Ember Placement

36

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

I. Optional Blower

The GFK-160ABlower has been designed to circulate room air through the appliance to enhance heat output.

The GFK-160Ablower system operates on 120 VAC, 60 Hz power. This is available through a receptacle in the factory installed junction box. The junction box is mounted in the bottom of the appliance behind the access panel. A variable speed control is provided with the blower system to provide quiet forced air flow at the desired speeds. A temperature sensor switch, which automatically turns the blower ON/OFF, is also provided with this kit.

Compare contents of carton with the actual parts received. If any parts are missing or damaged, contact your dealer before starting installation. Do not install a damaged blower kit. See Figure 8.21.

WARNING

Shock Risk

Explosion Risk

Do NOT wire 110V to gas control valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

Disconnect all electrical power. Remove the front door assembly by lifting off of appliance. Remove the lower access door. See Figure 8.22.

BLOWER

 

CONTROL

 

KNOB

 

GROUND

TEMP.

CLIP

 

SENSOR

CONTROL

SWITCH

NUT

 

WING NUT

SPEED

CONTROL

Figure 8.21

Installation precautions

The GFK-160ABlower kit is tested and safe when installed in accordance with this installation manual. It is your responsibility to read all instructions before starting installation and to follow these instructions carefully during installation to assure maximum benefit from, and safe operation, of the blower.

This blower is carefully engineered and must be installed only as specified. If you modify it or any of its components, you may cause a fire hazard and will void the WARRANTY. In addition, such action may void the coverage provided by the owner's home insurance.

CAUTION

All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the National Electric Code ANSI/NFPA NO. 70-current(in the United States), or with the current CSA C22.1 Canadian Electric Code (in Canada).

Figure 8.22

Attach enclosed wires to the temperature sensor switch/ bracket assembly. The blue wire attaches to the rear of the bracket and one of the black wires from the variable speed control attaches closest to the prepunched screw hole. See Figure 8.23.

Black Wires

Blue Wires

Figure 8.23

Feed the blue wire and other black wire from the variable speed control behind the gas valve assembly. Insert the wires into the slots indicated in Figure 8.28.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

37

Locate the machine screw underneath the firebox on the right side. Position the temperature sensor switch/bracket assembly over the machine screw and attach with the wing nut. Finger tighten. See Figure 8.24.

Attach the ground clip to the control panel. Attach the ground wire extension to the ground clip. Attach the blower ground wire to the ground wire extension. Refer to Figure 8.26.

Figure 8.24

Note: The switch/bracket assembly must be installed so that the sensor switch makes contact with the bottom of the firebox.

Attach rheostat in mating feature of control shield so that orientation of control knob is downward. See Figure 8.25.

Figure 8.26

Plug the blower cord into the FAN outlet on the junction box.

Push excess wires neatly towards the rear of the appliance.

Slide the blower into the bracket as indicated in Figure 8.27. Ensure the blower is pushed back into the bracket to allow the replacement of the lower access door. The magnet strips located on the blower feet are designed to hold the blower in place.

Plug appliance in. Turn the 110-120VAC service "ON" at the circuit breaker and turn the speed control switch to the "ON" position.

FAN BASE CONTACTS

FAN BRACKET

Figure 8.25

Figure 8.27

38

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

Recommended operating procedures

Ignite the fire in the appliance with the variable speed control switch in an "ON" position. The fan will automatically turn on when the temperature sensor switch closes at approximately 110 degrees Fahrenheit. Heated air should be delivered at the outlet grille. The fan will continue to operate after the appliance is turned OFF until the sensor switch opens.

Various conditions (such as appliance model, type of appliance installation, outside air temperature vs. inside air temperature) can contribute to the length of the time the blower remains on after the appliance is turned OFF. The blower can be turned off manually with the speed control switch.

VARIABLE

SPEED SWITCH

JUNCTION BOX

TEMPERATURE

SENSOR SWITCH

BLUE

Figure 8.28 Blower Wiring Diagram

WARNING! Risk of Shock! Replace damaged wire with type 105º C rated wire.

Wire must have high temperature insulation.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

39

J. Remote Controls

Tools Required: Powered screwdriver with Phillips head bit; hex wrench; 7/16 in. wrench; manometer.

Disconnect electricity at the circuit breaker before beginning this installation.

Familiarize yourself with the instructions enclosed with the remote control kit.

Remote receiver

Remove the top plate from the appliance. Remove the Allen head screws attaching the back panel to the appliance. Retain screws.

Remove the front glass door assembly and the lower access door.

Using two wire ties from the appliance component bag, mount the remote receiver to the rear of the control panel.

Feed the red and orange wires to the front of the appliance. Remove the optional blower, if installed.

Plug the 3-prongremote receiver cord into the junction box (REM/AUX). Refer to Figure 8.29.

Plug the 2-prongblower cord directly into the3-prongpolarized plug on the back of the receiver. This receptacle output is 110/120 VAC, 3 AMP.

Attach the ground wire from the blower onto the grounding clip.

Attach red wires from the remote receiver to the ON/OFF switch.

Reinstall the blower into the blower bracket.

3 Prong Cord

Wires Ties

Figure 8.29

Installing flame control solenoid

Remove the screw and knob from the variable regulator and discard. Unscrew the nut from the regulator and discard.

Remove the bag containing a washer and blue and red plungers from the side of the flame control solenoid.

Place washer on flame control solenoid. Insert the correct plunger (blue - Natural Gas, red - LP) into the flame control solenoid.

Thread the flame control solenoid with the correct plunger into the thread hole in the variable regulator. Turn one to two turns only. DO NOT tighten or damage may occur. See Figure 8.30.

GAS CONTROL

VALVE

WASHER

VARIABLE

REGULATOR

FLAME CONTROL

SOLENOID

KNOB

SCREW

NUT

VARIABLE

REGULATOR

WASHER

FLAME

CONTROL

SOLENOID

JAM NUT

PLUNGER

Figure 8.30 Flame Control Solenoid

40

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

Wiring the flame control solenoid:

Connect the two leads from the flame control solenoid to the orange leads from the receiver. See Figure 8.31.

Install a manometer into the pressure tap. Plug the remote receiver into the 110-120VAC power supply.

Light the appliance as directed in Section 9 of this manual. Set the manifold pressure on the gas valve by rotating the flame control solenoid. Adjust until the reading on the manometer is 3.5 in. W.C. for natural gas or 10 in. W.C. for LP.

Tighten the jam nut to the face of the variable regulator body. See Figure 8.30. Turn the main gas knob on the gas valve OFF. Remove the manometer from the pressure tap and screw the tap closed.

Follow the instructions from the remote control kit to operate and program the remote control.

 

REMOTE RECEIVER

 

 

 

 

 

 

REMOTE

 

 

 

 

 

 

RECEIVER

 

 

 

 

 

 

IGNITION MODULE

INTERMITTENT

 

 

 

3 VAC

PILOT IGNITOR

 

 

REDRED ORANGEORANGE

 

I

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

WHITE

 

 

TRANSFORMER

 

 

 

 

 

3 VAC

 

 

 

 

 

 

 

 

 

 

ORANGE

 

 

 

 

BRN

GROUND TO

 

 

PLUG

 

FIREPLACE CHASSIS

 

IN

 

BRN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RED

 

RED JUMPER

 

 

 

RED

 

 

 

 

 

WIRE TO

ORANGE

GREEN

 

BLACK

RED

 

BROWN

 

 

 

 

REDRED

 

 

 

 

BRN

 

 

BATTERY PACK

 

 

 

VALVE

 

 

 

 

 

 

 

 

PIGGYBACK

 

 

 

 

ON/OFF SWITCH

 

 

 

 

 

 

 

 

FLAME

 

 

 

 

 

 

CONTROL

 

 

 

 

 

 

SOLENOID

 

 

 

 

 

ORANGE

ORANGE

 

 

ORANGE

 

 

 

 

 

ORANGE

 

 

 

 

Figure 8.31 Remote Control IPI Wiring Diagram

 

 

 

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

41

K. Front Door Glass Assembly Replacement

Remove the front door assembly by pulling bottom of front away from appliance and lifting it off of the spring-loadedlatches on top of the appliance. See Figure 8.32.

Figure 8.32

Position the four flat 1/4 in. (6 mm) spacer washers on the front door so that the four mounting screws pass through them. Position the glass over the front door.

Install the four protective barrels into the glass and the four nylon washers on top of the glass.

From inside the door front, pass the screws through to the outside and thread on the caps until tight. See Figure 8.33.

CAP AND BARREL FASTENER SYSTEM

 

Nylon washer on back

Screw

and front of glass

 

Finishing Cap

Protective barrel sleeve through hole in the glass

of side Back door front

Figure 8.33

L. Inner Glass Door Assembly Replacement

Turn the appliance OFF and let it cool down before replacing the inner glass door assembly.

With the front door assembly removed from the appliance, remove the inner glass door assembly by disengaging the spring-loadedlatches at the bottom of the appliance and lifting off of the twospring-loadedlatches at the top of the appliance.

Replace with a new inner glass door assembly.

Figure 8.34 Complete Assembly

WARNING! Risk of Asphyxiation! Handle glass door assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace glass door as a complete assembly.

42

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

9 Operating Instructions

A. Before Lighting Appliance

Read this entire manual prior to using the appliance. Failure to follow the instructions may result in property damage, bodily injury, or even death.

CAUTION

If installing IntelliFire ignition battery backup:

Do not install batteries if the backup mode may not be used for extended time.

Batteries may leak.

Install batteries only when needed for power outage.

Before operating this appliance have a qualified technician:

Remove all shipping materials from inside and/or underneath the firebox.

Review proper placement of logs and mineral wool.

Check the wiring.

Check the baffle adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position.

Ensure that the flow of combustion and ventilation air is not obstructed (front grilles and vent caps).

WARNING

Glass door must be in place when appliance is operating.

Risk of:

Combustion Fumes

Fire

Do NOT operate appliance with glass door removed.

Open viewing glass for servicing only.

Glass door MUST be in place and sealed before operating appliance.

Only use glass door certified for use with appliance.

Glass replacement should be done by qualified technician.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/ or gas control which has been under water.

B. Controls

On/off Switch: When this switch is in the ON position, the pilot ignitor is engaged until temperature is established. The burner automatically turns on.

Valve Variable Control: This knob controls the flame height from low (“LO”) to high (“HI”). The indicator on the valve indicates the position of the knob.

Variable Speed Control: The blower is optional installed on the appliance and this knob controls the speed of the blower that pushes the heated air into the room.

Note: If using a remote control wall switch, or thermostat, the On/Off Switch must be left “OFF”. Turning the On/Off Switch to “ON” will keep the appliance on continually.

CONTROL PANEL

 

Valve Variable Control

Variable Speed

 

 

 

 

Control Knob

ON/OFF Switch

FutureOptional

LocationSwitch

 

Figure 9.1

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

43

C. Lighting Instructions (IPI)

The IPI system may be operated with two D-cellbatteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS (IPI)

1.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

3.To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4.If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2.Service technician should turn off electric power to the control when performing service.

593-913G

Final inspection by

44

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

D. After Appliance is Lit

Initial Break-inProcedure

When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

NOTE: The appliance should be run three to four hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours. This will help to cure the products used in the paint and logs.

During this break-inperiod it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

WARNING

Fire Risk.

High Temperatures.

Keep combustible household items away from appliance.

Do NOT obstruct combustion and ventilation air.

Do NOT place combustible items on top of or in front of appliance.

Keep furniture, draperies away from appliance.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

CAUTION

Smoke and odors released during initial operation.

Open windows for air circulation.

Leave room during initial operation.

Smoke may set off smoke detectors.

Smoke and odors may be irritating to sensitive individuals.

WARNING

Fire Hazard.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

Do NOT store flammable materials in the appliance’s vicinity.

Do NOT use gasoline, lantern fuel, kerosene,

charcoal lighter fluid or similar liquids in this appliance.

• Combustible materials may ignite.

E. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the fireplace warms, this

condensation will disappear.

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the fireplace is al-

lowed to burn for 20 to 40 minutes.

 

 

When first operated, this fireplace may release an odor for the first several hours. This is caused

Odor from fireplace

by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may

 

also be released from finishing materials and adhesives used around the fireplace.

Film on the glass

This is a normal result of the curing process of the paint. Glass should be cleaned within 3

to 4 hours of initial burning to remove deposits left by oils from the manufacturing process. A

 

 

non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the fireplace.

Is it normal to see the pilot flame burn

In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is

turned off. Some optional control systems available with IPI models may allow pilot flame to

continually?

remain lit. In a standing pilot system the pilot will always stay on.

 

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

45

10 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician.

A. IntelliFire Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

A. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

The ignitor/module

 

connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

B. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

spark.

 

shorts in the wiring.

ule to pilot assembly. Verify connections underneath pilot assem-

 

 

bly are tight; also verify connections are not grounding out to metal

 

 

chassis, pilot burner, pilot enclosure, mesh screen if present, or any

 

 

other metal object.

 

 

 

 

C. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

D. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5

 

 

mm) away from “I” terminal on module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode. Replace pilot if necessary.

 

 

 

2. Pilot won’t light,

A. No power or transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly.

voltage of transformer under load at spade connection on module

spark.

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

B. A shorted or loose connection in

Remove and reinstall the wiring harness that plugs into module.

 

wiring configuration or wiring har-

Verify there is a tight fit. Verify pilot assembly wiring to module. Re-

 

ness.

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

C. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

D. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF rocker switch or wall

 

 

switch in ON position. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

3. Pilot sparks, but

A. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits, inlet pressure must not

 

 

exceed 14 in. W.C.

 

 

 

 

B. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

D. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

 

solenoid ohms readings.

age is below 2.7.

 

 

 

46

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

IntelliFire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

A. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify con-

ues to spark, and main

 

nections are not grounding out to metal chassis, pilot burn-

burner will not ignite.

 

er, pilot enclosure or screen if present, or any other metal

(If the pilot continues

 

object.

to spark after the

 

 

B. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. Verify cor-

not occurred.)

 

 

rect pilot orifice is installed and gas inlet is set to pressure

 

 

 

 

specifications. Polish flame sensing rod with fine steel wool

 

 

to remove any contaminants that may have accumulated on

 

 

flame sensing rod.

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of ap-

 

 

pliance. Verify that wire harness is firmly connected to the

 

 

module.

 

 

 

 

D. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing rod

 

nated flame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

flame sensing rod to white sensor wire. Polish flame sens-

 

 

ing rod with fine steel wool to remove any contaminants

 

 

that may have accumulated on flame sensing rod. Verify

 

 

continuity with a multimeter with ohms set at lowest range.

 

 

Replace pilot if any damage is detected.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

switch or wall switch in ON position. If there is no spark at “I”

 

 

terminal module must be replaced. If there is a spark at “I”

 

 

terminal, module is fine.

 

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

47

11 Maintaining and Servicing Appliance

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

Turn off gas.

Turn off electricity to appliance.

Disable remote control, if one is present.

Ensure appliance is completely cooled.

After servicing:

Replace any screen or barrier that was removed.

Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

Condition of glass, glass assembly and glass seal.

Obstructions of combustion and ventilation air.

Burner ignition and operation.

Burner air shutter adjustment

Gas connections and fittings.

Obstructions of termination cap.

Clean:

Glass

Air passageways, grilles, control compartment

Burner, burner ports

Risk of:

Fire

Delayed ignition or explosion

Exposure to combustion fumes

Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial3-4hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when hot.

Turn off appliance after 3-4hours of operation and ALLOW TO COOL.

Remove and clean glass assembly.

Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

48

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

A. Maintenance Tasks

Inspect

 

Maintenance Tasks

 

1.

Inspect for scratches, dents or other damage and repair as necessary.

 

 

 

 

2.

Verify no obstructions to airflow through the louvers.

 

 

 

 

3.

Verify maintenance of proper clearance to combustible household objects.

 

 

 

Gasket Seal, Glass

1.

Inspect gasket seal and its condition.

Assembly and Glass

 

 

2.

Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.

 

 

 

 

 

3.

Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

4.

Verify that latches engage properly, clip studs are not stripped, and glass attachment components are

 

 

intact and operating properly. Replace as necessary.

 

5.

Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.

 

 

 

Valve Compartment

1.

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw

and Firebox Top

 

tips that have penetrated the sheet metal are sharp and should be avoided.

 

 

 

 

2.

Remove any foreign objects.

 

 

 

 

3.

Verify unobstructed air circulation.

 

 

 

Rocks

1.

Inspect for broken, damaged, or missing rocks. Replace as necessary.

 

 

 

 

2.

Verify correct rock placement and no flame impingement causing sooting. Correct as necessary.

 

 

 

Firebox

1.

Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.

 

 

 

 

2.

Replace appliance if firebox has been perforated.

 

 

 

Burner Ignition and

1.

Verify burner is properly secured and aligned with pilot or igniter.

Operation

 

 

2.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

 

 

 

 

 

3.

Replace ember materials with new dime-sizeand shape pieces. Do not block ports or obstruct lighting paths.

 

 

 

 

4.

Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.

 

 

 

 

5.

Inspect for lifting or other flame problems.

 

 

 

 

6.

Inspect orifice for soot, dirt or corrosion.

 

 

 

 

7.

Verify manifold and inlet pressures. Adjust regulator as required.

 

 

 

 

8.

Inspect pilot flame strength. Clean or replace orifice as necessary.

 

 

 

 

9.

Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Polish with fine

 

 

steel wool or replace as required.

 

10.

Verify millivolt output. Replace as necessary.

 

 

 

Venting

1.

Inspect venting for blockage or obstruction such as bird nests, leaves, etc.

 

 

 

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

 

 

 

3.

Verify that termination cap clearance to subsequent construction (building additions, decks, fences or

 

 

sheds) has been maintained.

 

4.

Inspect for corrosion or separation.

 

 

 

 

5.

Verify weather stripping, sealing and flashing remains intact.

 

 

 

Remote controls

1.

Verify operation of remote.

 

 

 

 

2.

Replace batteries in remote transmitters and battery-poweredreceivers.

 

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

49

12 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

 

A

 

 

 

 

 

 

 

 

B

 

 

C

 

 

 

 

 

 

D

 

Height includes 3/8 in (9.53 mm) hearth pad

 

 

 

 

E

 

 

 

 

 

 

 

 

F

 

 

 

 

G

 

 

 

 

I

 

 

Hearth Pad

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

Height includes 3/8 in (9.53 mm) hearth pad

 

Location

Inches

Millimeter

Location

Inches

Millimeter

 

A

18-7/8

479

F

7-1/8

181

 

B

40-3/4

1035

G

30

762

 

C

40-3/8

1025

H

28-7/8

733

 

D

15-7/8

403

I

34-5/8

879

 

E

3

76

 

 

 

Figure 12.1

Appliance Dimensions

 

 

 

 

 

50

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

B. Vent Components Diagram

 

6-1/2in.

 

 

165 mm

 

 

6-9/16in.

 

 

167 mm

 

 

6-9/16in.

 

9-7/16in.

167 mm

9-1/4in.

6 in.

235 mm

240 mm

152 mm

 

 

 

 

6-5/8in.

 

6-5/8in.

168 mm

 

168 mm

9-3/4in.

 

 

 

 

248 mm

 

SLP45

 

SLP90

 

 

 

 

6-5/8in.

 

6-5/8in.

168 mm

 

 

6-5/8in.

168 mm

 

168 mm

 

7-1/4in.

5-1/4in.

 

 

184 mm

133 mm

 

 

6-5/8in.

 

 

168 mm

 

 

13-1/4in.

6-9/16in.

 

337 mm

167 mm

SLP6

7-1/4in.

 

184 mm

SLP4

 

 

6-5/8in.

 

 

168 mm

6-9/16in.

 

 

167 mm

 

 

SLP12A

SLP6A

6-5/8in.

168 mm

6-5/8in.

168 mm

49-1/4in.

1251 mm

37-1/4in.

946 mm

6-5/8in.

168 mm

25-1/4in.

641 mm

13-1/4in.

337 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6-9/16in.

 

 

 

 

 

 

 

 

6-9/16in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6-9/16in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6-9/16in.

 

 

 

 

 

 

 

 

167 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

167 mm

 

 

 

 

 

 

 

167 mm

 

 

 

 

 

 

 

167 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLP12

 

 

 

 

 

 

SLP24

 

SLP36

 

 

 

 

 

SLP48

Note: Pipes overlap 1-3/8inches (34.93 mm) at each joint.

Figure 12.3 SLP Series Vent Components

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

51

C. Vent Components List

 

COMPONENTS

SLP-WT-BK

Ceiling Support / Wall Thimble, Black

SLP-CCS-BK

Cathedral Ceiling Support, Black

SLP6-BK

6 inch Pipe Length, Black

 

 

SLP4-BK

9 inch Pipe Length, Black

SLP12-BK

12 inch Pipe Length, Black

SLP34-BK

24 inch Pipe Length, Black

SLP36-BK

36 inch Pipe Length, Black

SLP48-BK

48 inch Pipe Length, Black

SLP6A-BK

11 inch - 14-5/8inch Pipe Length, Black

SLP12A-BK

12 inch - 17 inch Pipe, Adjustable, Black

SLP45-BK

45 degree Elbow, Black

SLP90-BK

90 degree Elbow, Black

SLP4

4 inch Pipe

SLP6

6 inch Pipe

SLP12

12 inch Pipe

SLP24

24 inch Pipe

SLP36

36 inch Pipe

SLP48

48 inch Pipe

SLP45

45 degree Elbow

SLP90

90 degree Elbow

SLP6A

3-6in. Adjustable Pipe Extension

SLP12A

3-12in. Adjustable Pipe Extension

SLP-RF6

0/12 - 6/12 Roof Flashing

SLP-RF12

7/12 - 12/12 Roof Flashing

SL-SCD

Storm Collar

SLP-FS

Ceiling Firestop

SLP-WS

Wall Firestop

SLP-HVS

Pipe Support Hanger

950

Vinyl Protector Kit - SL Pipe

DRC-RADIUS

Decorative Radius Cover

HTI-DV-WT

Wall Thimble

SLP-SA

Flue Adaptor

TERMINATION KITS

SLP-TRAP2

 

Trapezoid Termination Kit

SLP-TVHW

 

Vertical Termination Cap - High Wind

SRVSLK-991DA

 

Vertical Termination Cap

SLP-SK-BK

 

Horizontal Termination Kit (includes

 

 

904B, 930D, SLK-01TRD)

SLK-SNKD

 

Snorkel Kit

LINK-STOVE

 

Adapter Kit (includes 30 ft. of 4 inch

 

 

flex, apapters, wall thimble, masonry

 

 

& ZC flashing, 991DA cap and

 

 

hardware package

VPK-DV

 

Vinyl Siding Protector Kit

SLP-HHW2

 

HHW2 Horizontal High Wind

 

 

Cap (recommended for optimal

 

 

performance)

SLP-HRC-SS

 

SLP High Rise Cap-stainlesssteel

SLP-HRC-ZC-SS

 

SLP Zero Clearance High Rise Cap-

 

 

stainless steel

899-4491

 

HHW2K Horizontal Kit (one 90

 

 

degree black wall thimble, 24 inch

 

 

black

 

 

pipe, 11 inch - 14-5/8inch adjustable

 

 

vent, HHW2 termination cap)

844-8921

 

RHVK Snorkel Kit (with Dura-Vent

 

 

parts 911B and 940)

 

MISCELLANEOUS

46DVA-SC

 

Storm Collar

46DVA-FS

 

Ceiling Firestop

46DVA-WS

 

Wall Strap

46DVA-IS

 

Attic Insulation Shield

46DVA-GK

 

Chimney Liner Termination Kit

46DVA-GCL

 

Co-axial /Co-linealAppliance

 

 

Connector

46DVA-KMC

 

Retrofit Adj. Chimney Connector

 

 

Retrofit Chimney Connector Plate

NOTICE: The PVK-80power vent kit is NOT approved for use withPALOMA-BZ-MOD,PALOMA-GR-MOD,orPALOMA-GY-MOD.

52

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

D. Service Parts

PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMAGY-MOD

 

 

Service Parts Diagram

Beginning Manufacturing Date: Aug 2009

 

Ending Manufacturing Date: ______

Paloma-GY-MOD( Gray),Paloma-GR-MOD( Green),Paloma-BZ-MOD(Bronze))

1

2

3

4

20 21

5

6

19 7

8

9

18

12

10

16

17

11

15

 

 

 

Rock Placement

14

13

Part number list on following page.

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

53

D. Service Parts List

PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMAGY-MOD

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Rock Assembly

 

Paloma-Rock

 

1

Removable Top Assembly Top Vent

 

2123-012

 

Removable Top Assembly Rear Vent

 

2123-025

 

 

 

 

2

Top Assembly

 

7031-013

 

3

SLP Stove Adaptor

 

SLP-SA

 

4

Starting Collar Assembly

 

2189-002

 

5

Gasket, Adaptor

 

460-0610

 

6

Side Assembly Left

 

2123-027

 

7

Latch Assembly Upper

 

7003-006

Y

8

Heat Shield Baffle

 

2189-106

 

9

Heat Shield

 

2189-105

 

10

Access Door Assembly

 

7031-023

 

11

Burner Assembly

 

2189-005

Y

12

Glass Frame Assembly

 

2189-004

Y

 

 

Bronze

2123-028

 

13

Front Door Assembly

Green

2123-029

 

 

 

Gray

2123-016

 

 

Cap and Barrel Assembly

 

2123-019

 

14

Valve Plate Assembly

 

2189-003

 

15

Air Deflector

 

2123-185

 

16

Latch Assembly Lower

Pkg of 2

33858/2

Y

17

Control Assembly

 

7031-027

Y

 

Control Module

 

593-592

Y

 

Junction Box

 

4021-013

Y

 

Power Cord

 

832-2410

Y

 

Wire Assembly

 

593-590A

Y

 

3V Transformer

 

593-593A

Y

 

Battery Pack

 

593-594A

Y

18

Side Assembly Right

 

2123-026

 

19

Back Panel Assembly Vertical

 

7031-021

 

Back Panel Assembly Horizontal

 

7031-022

 

 

 

 

20

Cover Plate

 

2189-111

 

21

Cover Plate Gasket

 

7010-160

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Additional service part numbers appear on following page.

54

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

D. Service Parts

PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMAGY-MOD

Beginning Manufacturing Date: Aug 2009

Ending Manufacturing Date: ______

#22 Bottom Plate Assembly

22.1

22.10

22.2

22.3

22.9

22.4

22.8

22.6

22.5

22.7

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

 

parts for your appliance please provide model number and serial number. All parts listed

 

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

 

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

22.1

Pilot Assembly NG

 

2090-012

Y

 

Pilot Assembly LP

 

2090-013

Y

 

 

 

 

22.2

Burner Support

 

7031-279

 

 

22.3

3-HoleGrommet

 

2118-420

 

 

22.4

Orifice NG (#38C)

 

582-838

Y

 

Orifice LP (#53C)

 

582-853

Y

 

 

 

 

22.5

Valve NG

 

750-500

Y

 

Valve LP

 

750-501

Y

 

 

 

22.6

Burner Shelf

 

2189-113

 

 

22.7

Male connector

Pkg of 5

303-315/5

Y

 

22.8

Flex Ball Valve Assembly

 

2098-034

Y

 

22.9

Flex 12"

 

383-302A

Y

 

22.10

Pilot Bracket

 

2189-119

 

 

Additional service part numbers appear on following page.

 

 

 

 

 

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

55

D. Service Parts List

PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMAGY-MOD

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Temp Sensor

 

107-531

Y

 

Switch On/Off Rocker

 

230-0730

Y

 

Variable Speed Control

 

100-510A

Y

 

Air Deflector

 

2123-185

 

 

Flue Collar

 

7018-117

 

 

Flue Restrictor Plate

 

2189-118

 

 

 

 

 

 

 

 

 

 

 

 

Conversion Kit NG

 

NGK-PALOMA-MOD

Y

 

Conversion Kit LP

 

LPK-PALOMA-MOD

Y

 

Pilot Orifice NG

 

593-528

Y

 

Pilot Orifice LP

 

593-527

Y

 

Regulator NG

 

NGK-DXV

Y

 

Regulator LP

 

LPK-DXV

Y

 

Blower with Rheostat

 

GFK-160A

 

 

Remote Control

 

RCT-MLT-HNG

 

 

Wall Thermostat

 

WH-STAT

 

 

Wall Switch Kit (Off white)

 

WSK-21

 

 

Wall Switch Kit (White)

 

WSK-21-W

 

 

Rear Vent Conversion Kit

 

VRT-TR-AU

 

 

 

Bronze

PAL-GLS-BZ

 

 

Front Glass

Green

PAL-GLS-GR

 

 

 

Smoke

PAL-GLS-GY

 

 

 

Bronze

HP-PAL-BZ

 

 

Standard Hearth Pad

Green

HP-PAL-GR

 

 

 

Smoke

HP-PAL-GY

 

 

Touch Up Paint (Pewter)

 

TUPNP-12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

56

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

E. Limited Lifetime Warranty

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

 

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

Parts

Labor

Gas

Wood

Pellet

EPA

Coal

Electric

Venting

Components Covered

 

 

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

 

 

1 Year

X

X

X

X

X

X

X

covered by Conditions,

 

 

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

 

 

2 years

 

 

 

 

and glass

 

 

 

 

 

 

 

 

 

 

 

X

X

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

X

X

 

 

 

Manifold tubes,

 

 

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

Burners, logs and refractory

 

 

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

X

X

X

 

 

Firebox and heat exchanger

 

 

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

X

X

All replacement parts

 

 

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

4021-645C12-29-10

 

 

 

 

 

 

 

Page 1 of 2

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

57

E. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

7KLV ZDUUDQW\ RQO\ FRYHUV ++7 DSSOLDQFHV WKDW DUH SXUFKDVHG WKURXJK DQ ++7 DXWKRUL]HG GHDOHU RU GLVWULEXWRU $ OLVW RI ++7 DXWKRUL]HG GHDOHUV LV DYDLODEOH RQ WKH ++7 EUDQGHG ZHEVLWHV

7KLV ZDUUDQW\ LV RQO\ YDOLG ZKLOH WKH ++7 DSSOLDQFH UHPDLQV DW WKH VLWH RI RULJLQDO LQVWDOODWLRQ

&RQWDFW \RXU LQVWDOOLQJ GHDOHU IRU ZDUUDQW\ VHUYLFH ,I WKH LQVWDOOLQJ GHDOHU LV XQDEOH WR SURYLGH QHFHVVDU\ SDUWV FRQWDFW WKH QHDUHVW ++7 DXWKRUL]HG GHDOHU RU VXSSOLHU $GGLWLRQDO VHUYLFH IHHV PD\ DSSO\ LI \RX DUH VHHNLQJ ZDUUDQW\ VHUYLFH IURP D GHDOHU RWKHU WKDQ WKH GHDOHU IURP ZKRP \RX RULJLQDOO\ SXUFKDVHG WKH SURGXFW

&KHFN ZLWK \RXU GHDOHU LQ DGYDQFH IRU DQ\ FRVWV WR \RX ZKHQ DUUDQJLQJ D ZDUUDQW\ FDOO 7UDYHO DQG VKLSSLQJ FKDUJHV IRU SDUWV DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

WARRANTY EXCLUSIONS:

7KLV ZDUUDQW\ GRHV QRW FRYHU WKH IROORZLQJ

&KDQJHV LQ VXUIDFH ILQLVKHV DV D UHVXOW RI QRUPDO XVH $V D KHDWLQJ DSSOLDQFH VRPH FKDQJHV LQ FRORU RI LQWHULRU DQG H[WHULRU VXUIDFH ILQLVKHV PD\ RFFXU 7KLV LV QRW D IODZ DQG LV QRW FRYHUHG XQGHU ZDUUDQW\

'DPDJH WR SULQWHG SODWHG RU HQDPHOHG VXUIDFHV FDXVHG E\ ILQJHUSULQWV DFFLGHQWV PLVXVH VFUDWFKHV PHOWHG LWHPV RU RWKHU H[WHUQDO VRXUFHV DQG UHVLGXHV OHIW RQ WKH SODWHG VXUIDFHV IURP WKH XVH RI DEUDVLYH FOHDQHUV RU SROLVKHV

5HSDLU RU UHSODFHPHQW RI SDUWV WKDW DUH VXEMHFW WR QRUPDO ZHDU DQG WHDU GXULQJ WKH ZDUUDQW\ SHULRG 7KHVH SDUWV LQFOXGH SDLQW ZRRG SHOOHW DQG FRDO JDVNHWV ILUHEULFNV JUDWHV IODPH JXLGHV OLJKW EXOEV EDWWHULHV DQG WKH GLVFRORUDWLRQ RI JODVV

0LQRU H[SDQVLRQ FRQWUDFWLRQ RU PRYHPHQW RI FHUWDLQ SDUWV FDXVLQJ QRLVH 7KHVH FRQGLWLRQV DUH QRUPDO DQG FRPSODLQWV UHODWHG WR WKLV QRLVH DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

'DPDJHV UHVXOWLQJ IURP IDLOXUH WR LQVWDOO RSHUDWH RU PDLQWDLQ WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK WKH LQVWDOODWLRQ

 

LQVWUXFWLRQV RSHUDWLQJ LQVWUXFWLRQV DQG OLVWLQJ DJHQW LGHQWLILFDWLRQ ODEHO IXUQLVKHG ZLWK WKH DSSOLDQFH IDLOXUH WR

 

LQVWDOO WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK ORFDO EXLOGLQJ FRGHV VKLSSLQJ RU LPSURSHU KDQGOLQJ LPSURSHU RSHUD-

 

WLRQ DEXVH PLVXVH FRQWLQXHG RSHUDWLRQ ZLWK GDPDJHG FRUURGHG RU IDLOHG FRPSRQHQWV DFFLGHQW RU LPSURSHUO\

 

LQFRUUHFWO\ SHUIRUPHG UHSDLUV HQYLURQPHQWDO FRQGLWLRQV LQDGHTXDWH YHQWLODWLRQ QHJDWLYH SUHVVXUH RU GUDIWLQJ

 

FDXVHG E\ WLJKWO\ VHDOHG FRQVWUXFWLRQV LQVXIILFLHQW PDNH XS DLU VXSSO\ RU KDQGOLQJ GHYLFHV VXFK DV H[KDXVW IDQV RU

 

IRUFHG DLU IXUQDFHV RU RWKHU VXFK FDXVHV XVH RI IXHOV RWKHU WKDQ WKRVH VSHFLILHG LQ WKH RSHUDWLQJ LQVWUXFWLRQV

 

LQVWDOODWLRQ RU XVH RI FRPSRQHQWV QRW VXSSOLHG ZLWK WKH DSSOLDQFH RU DQ\ RWKHU FRPSRQHQWV QRW H[SUHVVO\ DXWKRUL]HG

 

DQG DSSURYHG E\ ++7 PRGLILFDWLRQ RI WKH DSSOLDQFH QRW H[SUHVVO\ DXWKRUL]HG DQG DSSURYHG E\ ++7 LQ ZULWLQJ

 

DQG RU LQWHUUXSWLRQV RU IOXFWXDWLRQV RI HOHFWULFDO SRZHU VXSSO\ WR WKH DSSOLDQFH

 

1RQ ++7 YHQWLQJ FRPSRQHQWV KHDUWK FRPSRQHQWV RU RWKHU DFFHVVRULHV XVHG LQ FRQMXQFWLRQ ZLWK WKH DSSOLDQFH

 

$Q\ SDUW RI D SUH H[LVWLQJ ILUHSODFH V\VWHP LQ ZKLFK DQ LQVHUW RU D GHFRUDWLYH JDV DSSOLDQFH LV LQVWDOOHG

++7¶V REOLJDWLRQ XQGHU WKLV ZDUUDQW\ GRHV QRW H[WHQG WR WKH DSSOLDQFH¶V FDSDELOLW\ WR KHDW WKH GHVLUHG VSDFH ,QIRUPDWLRQ LV SURYLGHG WR DVVLVW WKH FRQVXPHU DQG WKH GHDOHU LQ VHOHFWLQJ WKH SURSHU DSSOLDQFH IRU WKH DSSOLFDWLRQ &RQVLGHUDWLRQ PXVW EH JLYHQ WR DSSOLDQFH ORFDWLRQ DQG FRQILJXUDWLRQ HQYLURQPHQWDO FRQGLWLRQV LQVXODWLRQ DQG DLU WLJKWQHVV RI

WKH VWUXFWXUH

This warranty is void if:

7KH DSSOLDQFH KDV EHHQ RYHU ILUHG RU RSHUDWHG LQ DWPRVSKHUHV FRQWDPLQDWHG E\ FKORULQH IOXRULQH RU RWKHU GDPDJLQJ FKHPLFDOV 2YHU ILULQJ FDQ EH LGHQWLILHG E\ EXW QRW OLPLWHG WR ZDUSHG SODWHV RU WXEHV UXVW FRORUHG FDVW LURQ EXEEOLQJ FUDFNLQJ DQG GLVFRORUDWLRQ RI VWHHO RU HQDPHO ILQLVKHV

7KH DSSOLDQFH LV VXEMHFWHG WR SURORQJHG SHULRGV RI GDPSQHVV RU FRQGHQVDWLRQ

7KHUH LV DQ\ GDPDJH WR WKH DSSOLDQFH RU RWKHU FRPSRQHQWV GXH WR ZDWHU RU ZHDWKHU GDPDJH ZKLFK LV WKH UHVXOW RI EXW QRW OLPLWHG WR LPSURSHU FKLPQH\ RU YHQWLQJ LQVWDOODWLRQ

LIMITATIONS OF LIABILITY:

7KH RZQHU¶V H[FOXVLYH UHPHG\ DQG ++7¶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

4021-645C12-29-10

Page 2 of 2

58

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

F. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

2000-945

Printed in U.S.A. - Copyright 2012

Heat & Glo • PALOMA-BZ-MOD,PALOMA-GR-MOD,PALOMA-GY-MOD2189-900Rev. i • 5/12

59