Heat & Glo LifeStyle MTL-INSERT User Manual

Size:
2.05 Mb
Download

Owner’s Manual

Installation and Operation

Model:

MTL-Insert

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard, Title 24 CFR, Part 3280 orStandard for Installation in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts:

installation must be performed by a licensed plumber or gas fitter;

a CO detector shall be installed in the room where the appliance is installed.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

1

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 20802 Kensington Boulevard, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas (Sorte De Gaz): This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1

in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglementsNATURAL GAS locaux ou, en l’absence de tels reglements, selon les codes d’installationCAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

Approved Minimum (De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

Maximum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

Minimum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

IN CANADA

 

Model:

XXXXXXXX

ALTITUDE:

0-0000FT.

0000-0000FT.

(Modele):

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

(Serie):

Model Number

Serial Number

2

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

Table of Contents

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

B. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

C. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4

D. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 4

E. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4

F. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Getting Started

A. Design and Installation Considerations . . . . . . . . . . . . . . . 5

B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 5

C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 5

3 Fireplace Size Requirements

A. Minimum Fireplace Opening . . . . . . . . . . . . . . . . . . . . . . . 6

B. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . . 8

5 Vent Information and Diagrams

A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

B. Horizontal Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6 Installation Preparation

A. Flue Damper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 B. Chimney . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 C. Gas Line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. Hearth or Hearth Extension . . . . . . . . . . . . . . . . . . . . . . . 10 E. Fireplace Conversion Notice . . . . . . . . . . . . . . . . . . . . . . 10 F. Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7 Installing Vent Pipe and Appliance

A. Venting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

B. Connecting Vent Pipe. . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

C. Placing, Securing and Leveling the Appliance . . . . . . . . . 12

D. Installing Termination Cap . . . . . . . . . . . . . . . . . . . . . . . . 13

8 Gas Information

A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9 Electrical Information

A. Wiring the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Optional Junction Box Installation . . . . . . . . . . . . . . . . . . 17

10 Finishing

A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

11 Appliance Setup

A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 20

B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

D. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

E. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

F. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

G. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

12 Operating Instructions

A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 25 B. Lighting Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 C. Check Pilot Flame Appearance . . . . . . . . . . . . . . . . . . . . 27 D. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 E. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 28

13 Troubleshooting

A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 29

14 Maintaining and Servicing Appliance

A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

15 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 33

B. Vent Kits Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

D. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 38

E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

= Contains updated information.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

3

1 Listing and Code Approvals

A. Appliance Certification

MODELS: MTL-INSERT

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Vented Gas Fireplace Heaters

STANDARD: ANSIZ21.88a-2007/CSA2.33a-2007

ANSI Z21.88-2005/CSA2.33-2005

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

Note: To assure top performance, safety and efficiency, inserts must be installed with an approved flue liner as per CAN/CGAB-149or National Fuel Gas Code ANSI Z223 and these instructions.

Note: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

C. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

D. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750º C, shall be considered non-combustible materials.

B. BTU Specifications

Models

Maximum

Minimum

Orifice

Input

Input

Size

(U.S. or Canada)

BTU/h

BTU/h

(DMS)

 

 

 

US

32,000

22,000

#35

MTL-INSERT

(0-2000FT.)

 

 

 

(NG)

CANADA

28,800

19,800

#36

 

(2000-4500FT.)

 

 

 

 

 

US

31,000

18,000

#52

MTL-INSERT

(0-2000FT.)

 

 

 

(LP)

CANADA

27,900

16,220

#53

 

(2000-4500FT.)

 

 

 

 

 

 

 

 

 

E. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

F. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

4

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

2 Getting Started

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

Heat & Glo gas inserts are designed for recessed installations into solid fuel masonry or factory built non-combustiblefireplaces that have been installed in accordance with the National, Provincial, State and local building codes.

Prior to installing the gas insert:

Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

Replace component parts of the chimney and fireplace as specified by the professionals.

Ensure all joints are properly engaged and the chimney is properly secured.

When planning an appliance installation, it’s necessary to determine the following information before installing:

Minimum fireplace size. See Section 3.A.

Gas supply piping.

Electrical wiring.

Finishing details.

Existing mantel, mantel legs and wall projection locations. See Section 3.C.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

B. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Pliers

Hi temp caulking material

Hammer

Flat blade screwdriver

Voltmeter

Framing square

Gloves

Variable speed drill

1/4 Hex drive

Safety glasses

Manometer

Phillips screwdriver

Tape measure

Non-corrosiveleak check solution

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews

C. Inspect Appliance and Components

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

• Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components. Report damaged parts to dealer.

Carefully remove the appliance and components from the packaging.

The vent system components, surrounds and fronts are shipped in separate packages.

The fiber logs may be packaged separately and must be field installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING

Keep appliance dry.

• Mold or rust may cause odors.

• Water may damage controls.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

5

3 Fireplace Size Requirements

A. Minimum Fireplace Opening

Minimum fireplace opening requirements are shown in Figure 5.1.

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

The firebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed from a factory built firebox in order to gain minimum gas insert opening requirements.

Any smoke shelves, shields and baffles may be removed from the factory built firebox if attached with mechanical fasteners.

The metal floor of the solid fuel firebox may be removed to facilitate the installation of the insert. The appliance may not be placed directly on the base of the outer wrap, a 1/4 inch airspace must be provided between the insert and the floor of the outer wrap. Use the levelling legs to raise the insert a minimum of 1/4 inch. The original fireplace may never be returned to solid fuel in this condition. The sidewalls and top structure of the firebox may not be altered with the exception of removable baffles and dampers.

Cutting of any sheet metal parts of the fireplace in which the gas fireplace insert is to be installed is prohibited, except the floor as tested for and as noted above.

NOTE: For actual appliance dimensions refer to Section 15.

B

 

 

TOP VIEW

C

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum Appliance Size

 

 

 

 

 

 

 

 

Location

 

 

 

MTL-INSERT

 

 

 

 

 

 

 

 

 

 

 

 

Inches

 

Millimeters

 

 

 

 

 

 

 

A

 

Front Width

 

29-1/4

 

743

 

 

 

 

 

 

 

B

 

Rear Width

 

20-1/4

 

515

 

 

 

 

 

 

 

C

 

Depth

 

13-5/8

 

346

 

 

 

 

 

 

 

*

 

Height

 

20-1/4

 

515

 

 

 

 

 

 

 

* NOTE: If exhaust collar on insert and fireplace damper do not line up, add 4

 

 

 

 

 

 

 

inches (102 mm) to minimum fireplace height for bends in vent pipe.

 

 

Figure 3.1 Fireplace Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

Heat & Glo • MTL-Insert

2145-900Rev. F

• 9/08

 

 

B. Clearances

WARNING

Fire Risk.

Odor Risk.

• Clearance to combustible material under the insert is 1/4 inch (0.6 cm).

Use leveling legs to raise insert minimum 1/4 inch above combustible material or outer wrap of factory built firebox.

WARNING

Fire Risk.

• Locate and install appliance to all clearance specifications in manual.

INLET AIR

12 in. MAX.

EXHAUST VENT PIPE

 

VENT PIPE

 

 

MANTEL

15 in. MIN.

MEASUREMENTS FROM

TOP EDGE OF UNIT

Figure 3.2 Clearances to Mantels or other Combustibles above Appliance

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

7

4 Termination Locations

A. Vent Termination Minimum Clearances

Figure 4.1 specifies minimum vent heights for various pitched roofs.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5*

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 4.1 Minimum height from roof to lowest discharge opening

WARNING

Fire Risk.

Asphyxiation Risk.

Terminations MUST meet minimum clearances.

Exhaust gases are hot.

• Nearby vents may draw fumes into house.

8

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

5 Vent Information and Diagrams

A. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

VMIN

Minimum Vertical Run Length 14 ft.

VMAX

Maximum Vertical Run Length 50 ft.

B. Horizontal Venting

Horizontal venting is NOT allowed.

C. Measuring Standards

Vertical measurements listed in the vent diagram (Figure 5.1) were made using the following standard:

• Vertical terminations are measured to top of chimney.

WARNING

Fire Hazard. Explosion Risk. Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney flue serving a separate solid fuel or gas burning appliance.

May impair safe operation of this appliance or other appliances connected to the flue.

Vent this appliance directly outside.

Use separate vent system for this appliance.

CAUTION

ALL vent specifications MUST be followed.

This product is tested and listed to these specifications.

Appliance performance will suffer if specifications are not followed.

TERMINATION CAP

ADAPTOR

EXHAUST VENT PIPE

MIN. = 14FT.

MAX. = 50FT.

INSULATION SEAL

INLET VENT AIR PIPE

Figure 5.1

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

9

6 Installation Preparation

Prepare the existing solid fuel masonry or factory built non-combustiblefirebox for installation.

A. Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open position, OR completely remove it.

E. Fireplace Conversion Notice

Permanently attach the label with the following warning to the inside lower back of the fireplace firebox into which the insert is being installed. Silicone may be required to properly secure the label.

B. Chimney

Ensure chimney is constructed of non-combustiblematerials.

Ensure chimney is clean and in good working order.

Ensure that all chimney cleanouts fit properly to prevent air leakage into chimney.

C. Gas Line

Note: If the factory built fireplace has no gas access hole provided, an access hole of 1 inch (25 mm) diameter or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship - like manner. This access hole must be plugged withnon-combustibleinsulation after the gas supply line has been installed.

Install gas line into firebox cavity.

Check local codes and gas line sizing requirements following NFPA54. See Section 8.

WARNING

Fire Risk.

This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fireplace reapproved by the authority having jurisdiction.

Prior to installing the gas insert:

Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

Replace component parts of the chimney and fireplace as specified by the professionals.

Ensure all joints are properly engaged and the chimney is properly secured.

D. Hearth or Hearth Extension

WARNING

Fire Risk.

A hearth or hearth extension (if present) must comply with either of the following:

The solid fuel burning fireplace manufacturer’s specification.

• Local building codes required by authority having jurisdiction.

• NFPA 211

F. Remote Control

The receiver for the remotes must be installed BETWEEN the base pan of the insert and the firebox of the woodburning fireplace (see photo below).

EXISTING SIDE

REFRACTORY

REMOTE

RECEIVER

UNIT

EXISTING BOTTOM OF

FIREPLACE

Figure 6.1

Note: TheMTL-INSERTdoes not ship standard with a junction box. In order to use a remote control, a junction box must be installed.

10

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

7 Installing Vent Pipe and Appliance

A. Venting Components

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

The vertical vent termination system installed on this model includes:

One length of 3-inchflexible vent pipe for combustion air (included with vent kit). Pipe will be either a4-footor30-footsection depending on which kit is being used in the application.

Flexible vent pipe for exhaust air (included with vent kit).

One pipe-to-capadaptor (included with vent kit).

One vertical termination cap (included with vent kit).

B. Connecting Vent Pipe

Reference instructions in the termination kit.

Install the 3-inchflexible vent pipe(s) down through the chimney.

Use three screws to secure the exhaust flexible vent pipe to the 3 foot section stainless steel flexible vent pipe using the factory-installed3-inchcollar in the stainless steel section of pipe (see Figure 7.1).

Use 3 screws to attach either a 4 foot or 30 foot section of inlet air vent to the inlet collar on the collar slide plate (see Figure 7.1). NOTE: The collar slide plate may be removed from appliance to aid installation.

Seal opening between flex vent and chimney just above insert. Non-combustible,unfaced fiberglass insulation may be used for this purpose.

TERMINATION

 

 

 

 

CAP

 

 

 

 

 

 

 

INLET AIR STARTING COLLAR

 

EXHAUST

 

 

 

 

AIR

 

 

LOCKING TAB

 

VENT PIPE

 

 

 

 

 

 

 

 

 

 

STARTING COLLAR BRACKET

 

 

 

EXHAUST STARTING COLLAR

 

INLET AIR

 

 

 

 

VENT PIPE

 

 

 

 

INLET AIR STARTING COLLAR

 

 

 

STARTING COLLAR BRACKET

 

 

 

EXHAUST STARTING COLLAR

 

 

 

Figure 7.1

 

 

 

 

Heat & Glo • MTL-Insert

2145-900Rev. F

9/08

11

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 7.2).

Place 3/8 inch bead of 300º F silicone on flue tile top.

C.Placing, Securing and Leveling the Appliance

Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

Install gas line into hole provided on insert side.

If applicable install remote control wires into insert side (see Section 6F).

Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

Non-combustible,unfaced fiberglass insulation may be installed between the back of the decorative surround and the face of the existing fireplace surround to which the insert is being installed.

Attach surround. Follow instructions accompanying surround.

Push insert so that surround becomes tight against face of fireplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces.

• No other components such as shrouds, sheetmetal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

Connect vent sections per installation instructions.

The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

Do NOT allow vent to sag below connection point to appliance.

12

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

D. Installing Termination Cap

For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.3) .

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min . ) Ft.

Flat to 6/12

....................

1.0*

Over 6/12 to ........7/12

1.25*

Over 7/12 to ..........8/12

1.5*

Over 8/12 to ..........9/12

2.0*

Over 9/12 to ........10/12

2.5*

Over 10/12 .....to 11/12

3.25

Roof Pitch

H (Min.) Ft.

Over 11/12 to 12/12 .......

4.0

Over 12/12 to 14/12.......

5.0

Over 14/12 to 16/12.......

6.0

Over 16/12 to 18/12.......

7.0

Over 18/12 to 20/12.......

7.5

Over 20/12 to 21/12.......

8.0

* 3 foot minimum in snow regions

Figure 7.3 Minimum Height from Roof to Lowest Discharge Opening

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

Damper Flashing Kit (Optional)

For use with LINK-DV4-30BLiner Kit.

Note: Damper may have to be removed to use this kit.

Run flex liners through 3” holes in damper flashing.

Attach damper flashing to firebox roof with self tapping screws included in kit.

CLASS A PIPE

Figure 7.4

To help eliminate cold air drafts, it may be necessary to place non-

Note: TheLINK-DV4-30B

combustible insulation around the flues as they go though the damper.

system REQUIRES this insulation.

 

 

Masonry LINK-DV30B

LINK-DV4-30B

Installation

Installation

TERMINATION

CAP

EXHAUST

AIR

VENT PIPE

OR

WARNING:

DO NOT BLOCK

THIS PIPE END!

 

Note: Untwist

INLET AIR

the pipe while

extending it, to

VENT PIPE

achieve full 30’

 

 

length.

Figure 7.5

Factory Built

Wood Burning

OPTIONAL LINK-ZC-ADPB

FOR USE WITH CLASS A

WOODBURNING PIPE

Remove 18 inch x 18 inch flashing on cap by removing 3 screws. Connect both the LINK-ZC-ADPBto Class A Pipe and the termination cap to theLINK-ZC-ADPBwith the self tapping screws provided.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

13

8 Gas Information

A. Fuel Conversions

C. Gas Connection

Before making gas connections ensure that appliance being installed is compatible with the available gas type.

Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts.

Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

B. Gas Pressures

Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA54.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressures must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 inches

11.0 inches

w.c.

w.c.

 

Maximum inlet gas pressure

14.0 inches

14.0 inches

w.c.

w.c.

 

Manifold pressure

3.5 inches

10.0 inches

w.c.

w.c.

 

NOTE: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Refer to Reference Section 15 for location of gas line access in appliance.

NOTE: Gas line may be run from either side of the appliance provided the hole in the outer wrap does NOT exceed2-1/2inches in diameter and does not penetrate the firebox.

WARNING

Gas Leak Risk

Support control when attaching pipe to prevent bending gas line.

NOTE: The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed withnon-combustible,unfaced insulation to prevent cold air infiltration.

Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes.

Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.

Check all fittings and connections of appliance which may have loosened during shipping.

14

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

WARNING

Fire or Explosion Hazard

Gas buildup during line purge may ignite.

Purge should be performed by qualified technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING

CHECK FOR GAS LEAKS

Explosion Risk

Fire Risk

Asphyxiation Risk

Check all fittings and connections.

Do not use open flame.

After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially-available,non-corrosiveleak check solution. Be sure

to rinse off all leak check solution following testing.

Fittings and connections may have loosened during shipping and handling.

WARNING

Fire hazard.

Do NOT change the valve settings.

• This valve has been preset at the factory.

• Changing valve settings may result in fire hazard or bodily injury.

HIGH ALTITUDE INSTALLATIONS

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

15

9 Electrical Information

A. Wiring the Appliance

Appliance Requirements

Note: Electrical wiring must be installed by a licensed electrician.

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

This appliance DOES NOT require 110-120VAC to operate.

It is recommended that a 110 VAC junction box be connected for use with fan or remote control. (See Figure 9.2 for junction box wiring).

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

ON/OFF Switch

An ON/OFF switch is included with the door/front and should be attached to the door/front. The location of the ON/OFF switch varies depending on model. It may be installed on the valve cover plate or included with the decorative surround. (See Installation instructions for remote control).

If desired an additional wall switch or thermostat may be added to system as shown in Figure 9.1. Follow directions included with the optional wall switch.

STANDING

 

PILOT

 

 

 

REMOTE SWITCH

 

 

PIGTAIL

 

 

ON

 

 

OFF

 

VALVE

ON/OFF

 

SWITCH

 

 

 

WHT

 

 

RED

OPTIONAL WALL SWITCH,

 

 

THERMOSTAT OR REMOTE

Figure 9.1

Standing Pilot Ignition Wiring Diagram

 

16

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

B. Optional Junction Box Installation

 

JUNCTION BOX ACCESS

 

SIDEWALL

JUNCTION

BOX

 

 

SCREW

 

PROVIDED

Figure 9.2

Optional Junction box installation

Note: The MTL-INSERTdoes not ship standard with a junction box. The junction box is an optional accessory.

Optional Accessories

Connecting the electrical junction box is required if using a blower or remote.

Plug the cord into a convenient outlet.

An electrician may install an outlet box inside the fireplace. Place the outlet in the lower, back corner of the fireplace.

Must use cord supplied.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING

Shock hazard.

Replace damaged wire with type 105º C rated wire.

Wire must have high temperature insulation.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

17

 

VARIABLE SPEED CONTROL

 

 

 

JUNCTION BOX

 

BLK

BLK

 

 

 

 

 

 

BLK

 

BLOWER RECEPTACLE

 

 

 

BLK

BLK

 

 

 

BLK

 

BLK

 

 

 

 

 

BLK

WHT

WHT

 

GROUND

 

 

 

 

TEMPERATURE

 

 

BLOWER

 

GRN

 

SENSOR SWITCH

BLK

WHT

 

 

 

 

110-120VAC

 

 

 

FAN

JUNCTION

 

 

 

BOX

 

 

 

TEMPERATURE

 

 

 

SENSOR SWITCH

 

 

 

SPEED CONTROL

 

 

 

(RHEOSTAT)

 

BEND

 

GROUND WIRE

 

UP TABS

 

(ATTACH TO ANY

 

 

 

METAL SURFACE)

Figure 9.3 Fan/Rheostat Wire Diagram (Optional)

 

 

Note: The MTL-INSERTdoes not ship standard with a fan. The fan is an optional accessory.

18

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

10 Finishing

A. Mantel Projections

Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround.

INLET AIR

12 in. MAX.

EXHAUST VENT PIPE

 

VENT PIPE

 

 

MANTEL

15 in. MIN.

MEASUREMENTS FROM

TOP EDGE OF UNIT

Figure 10.1 Clearances to Mantels or other Combustibles above Appliance

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

19

11 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

• Embers CANNOT be placed directly over ports.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 15.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listedaccessories voids warranty.

Using non-listedaccessories may result in a safety hazard.

Only Hearth & Home Technologies approved

accessories may be used safely.

D. Ember Placement

WARNING

Explosion Risk.

Follow ember placement instructions in manual.

Do NOT place embers directly over burner ports.

Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place the dime-sizeember pieces near port holes in burner top, sides and front (see Figure 11.1). Failure to follow this procedure will likely cause lighting and sooting problems.

EMBER MATERIAL

Figure 11.1 Placement of Embers

Place Mystic Ember over burner surface and around base of burner. Do not cover any burner port holes. Use this material to give the appliance a realistic ash bed.

Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

20

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

E. Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

CAUTION: Logs are fragile! Carefully remove the logs from the packaging.

Log Set Assembly: LOGS-SXT

1

4

3

2 6

5

PILOT BURNER BASEPAN

GRATE

TABS

1

 

1

 

 

 

LOG #1 (SRV349-701): Place log #1 in the back of the insert. Locate the legs of the log outside the 3/8" tabs to either side of the burner. Pull the log forward until the log is stopped by the back edge of the burner.

349-9351/02

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

21

2

 

2

 

 

 

 

 

LOG #2 (SRV349-702): Position log #2 by locating its slot over the tab on the front left of the burner. The slot of the left side of log #2 fits over the bar grate. Push the left side back so it rests against the step.

3

 

3

 

 

 

 

 

LOG #3 (SRV327-703): Position log #3 by locating its slot over the tab on the right front of the burner. The slot on the right side of log #3 fits over the bar grate.

4

 

4

 

 

 

LOG #4 (SRV349-704): Place the bottom left corner of log #4 behind log #2 and rest its top right corner on log #1. The bottom left corner of the log rests in the square cut out of the base pan.

22

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

5

 

5

 

 

 

LOG #5 (SRV327-705): Rest log #5 in the cutouts on both log #1 and log #3 as shown. The front edge of log #1 should be at the top of the hole when looking through the hole in log #5.

6

6

LOG #6 (SRV349-706): Position the "Y" end of log #6 into the cutout on log #4 and its opposite end into the groove on log #2.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

23

F. Glass Assembly

WARNING

Handle glass doors with care.

Inspect the gasket to ensure it is undamaged.

Inspect the glass for cracks, chips or scratches.

Do NOT strike, slam or scratch glass.

Do NOT operate appliance with glass door removed, cracked, broken or scratched.

Replace glass door assembly as a complete appliance.

Removing Glass Assembly

There are two glass latches on bottom of the glass assembly.

To release glass assembly, pull latch forward and allow to retract away from glass assembly.

Remove glass assembly after the bottom two latches have been released (see Figure 11.5).

Replacing Glass Assembly

Replace the glass door on the appliance. Fasten the latches on the glass frame.

GLASS ASSEMBLY

BOTTOM LATCH

Figure 11.5 Glass Assembly

G. Air Shutter Setting

Optimal flame appearance is dependent on the air shutter setting. Adjustments should be made by a qualified technician.

Model

NG

LP

MTL-INSERT

3/8 in.

Full Open (3/4 in.)

24

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

12 Operating Instructions

A. Before Lighting Appliance

This appliance has a Standing Pilot Ignition.

Before operating this appliance have a qualified technician:

Remove all shipping materials from inside and/or underneath the firebox.

Review proper placement of logs, rockwool, lava rock, and vermiculite.

Check the wiring.

Check the air shutter adjustment.

Purge gas line (with glass assembly removed). See Section 8.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position.

Ensure that the flow of combustion and ventilation air is not obstructed (front grilles and vent caps).

WARNING

Fire Risk.

Explosion Risk.

Gas may build up while lighting pilot.

Remove glass assembly before lighting pilot.

Replace glass assembly after lighting pilot.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

25

B. Lighting Appliance

Standing Pilot Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. Do not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS

1.Turn off all electric power to the appliance.

2.Push in gas control knob slightly and turn clockwise

to “OFF”.

NOTE: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you don’t smell gas, go to next step.

4.Find the pilot. The pilot is inside combustion chamber next to the main burner.

5.Turn knob on gas control counter clockwise

to “PILOT”.

6.Push in control knob all the way and hold in. Immediately depress red or black piezo button. It may require several depressions of the red or black piezo button until PILOT lights. If PILOT light does not light after 10 seconds, return to step 3. Continue to hold the control knob in for about one minute after the pilot is lit. Release knob and it will pop back out. Pilot should remain lit. If it goes out, repeat steps 3 through 6.

If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

7.Turn gas control knob counterclockwise to

“ON”.

8.To light Burner, flip the on/off switch to the “ON” position, and close access grille.

9.Turn on all electric power to the appliance.

TO TURN OFFGAS TO APPLIANCE

1. Turn off all electric power to the appliance if service is to be performed.

2.

Open control access panel.

3.

Move switch to “OFF” position.

4.

Push in gas control knob slightly and turn clock-

 

wise

to OFF”. Do not force.

5.

 

Close control access panel.

 

 

464-903G

26

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

C. Check Pilot Flame Appearance

Pilot flame must contact the thermocouple and thermopile for reliable appliance operation.

Pilot flame should be as shown in Figure 12.1.

Figure 12.1 Proper Pilot Flame

If adjustment is needed remove cap screw from gas valve using 1/8 inch standard screwdriver (see Figure 12.2).

Turn adjustment screw clockwise to increase pilot flame size. Make small adjustments.

PILOT

ADJUSTMENT

Figure 12.2 Adjustments

Do NOT turn adjustment screwcounter-clockwisetoo far as it will come out of the valve allowing gas to escape.

Replace cap screw and seal to prevent gas leaks.

Check for gas leaks after tightening.

D. After Appliance is Lit

WARNING

Glass door must be in place when appliance is operating.

Risk of:

Combustion Fumes

Fire

Do NOT operate appliance with glass door removed.

Open viewing glass for servicing only.

Glass door MUST be in place and sealed before operating appliance.

Only use glass door certified for use with appliance.

Glass replacement should be done by qualified technician.

Initial Break-inProcedure

When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

Note: The appliance should be run three to four hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours. This will help to cure the products used in the paint and logs.

During this break-inperiod it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

27

WARNING

Fire Risk.

High Temperatures.

Keep combustible household items away from appliance.

Do NOT obstruct combustion and ventilation air.

Do NOT place combustible items on top of or in front of appliance.

Keep furniture, draperies away from appliance.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

CAUTION

Smoke and odors released during initial operation.

Open windows for air circulation.

Leave room during initial operation.

Smoke may set off smoke detectors.

Smoke and odors may be irritating to sensitive individuals.

WARNING

Fire Hazard.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

Do NOT store flammable materials in the appliance’s vicinity.

• Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids in this appliance.

• Combustible materials may ignite.

E. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

condensation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appliance is al-

lowed to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this appliance may release an odor for the first several hours. This is

Odor from appliance

caused by the curing of the paint and the burning off of any oils remaining from manufacturing

 

and might set off home smoke detectors.

 

 

 

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

Film on the glass

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See

 

your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the appliance.

 

 

Is it normal to see the pilot flame burn

In a standing pilot system the pilot will always stay on.

continually?

 

 

 

28

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

13 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

A. Standing Pilot Ignition System

Symptom

Possible Causes

Corrective Action

 

 

 

1. After repeated triggering

a. Defective ignitor.

Check the spark at the electrode and pilot. If no spark and electrode

of the red or black piezo

 

wire is properly connected, replace the ignitor.

ignitor button, the spark

 

 

b. Defective pilot or misaligned

Using match, light the pilot. If the pilot lights, turn off the pilot and

ignitor will not light the pilot.

 

electrode (spark at electrode).

trigger the red piezo ignitor button again. If the pilot lights, an im-

 

 

proper gas/air mixture caused the bad lighting and a longer purge

 

 

period is recommended. If the pilot will not light, ensure the gap

 

 

at the electrode and pilot is one-eighth(1/8) inch to have a strong

 

 

spark. If the gap is OK, replace the pilot.

 

 

 

 

c. No gas or low gas pressure.

Check the remote shut-offvalves from the fireplace. Usually, there

 

 

is a valve near the gas main. There can be more than one (1) valve

 

 

between the fireplace and the main.

 

 

 

 

d. No LP in tank.

Check the LP (propane) tank. You may be out of fuel.

 

 

 

2. The pilot will not stay lit

a. Defective thermocouple.

Check that the pilot flame impinges on the thermocouple. Clean

after carefully following the

 

and/or adjust the pilot for maximum flame impingement.

lighting instructions.

 

Ensure that the thermocouple connection at the gas valve is fully

 

 

 

 

inserted and tight (hand tighten plus 1/4 turn).

 

 

Disconnect the thermocouple from the valve, place one millivolt

 

 

meter lead wire on the tip of the thermcouple and the other meter

 

 

lead wire on the thermocouple copper lead. Start the pilot and hold

 

 

the valve knob in. If the millivolt reading is less than 15mV, replace

 

 

the thermocouple.

 

 

 

 

b. Defective valve.

If the thermocouple is producing more than 15 millivolts, replace

 

 

faulty valve.

 

 

 

3. The pilot is burning,

a. ON/OFF switch or wires

Check the ON/OFF switch and wires for proper connections. Place

there is no burner flame,

defective.

the jumper wires across the terminals at the switch. If the burner

the valve knob is in the ON

 

comes on, replace the defective switch. If the switch is OK, place the

position, and the ON/OFF

 

jumper wires across the switch wires at the gas valve. If the burner

switch is in the ON position.

 

comes on, the wires are faulty or connections are bad.

 

 

 

 

b. Thermopile may not be gener-

If the pilot flame is not close enough physically to the thermopile,

 

ating sufficient millivoltage.

adjust the pilot flame.

 

 

Be sure the wire connections from the thermopile at the gas valve

 

 

terminals are tight and that the thermopile is fully inserted into the

 

 

pilot bracket.

 

 

Check the thermopile with a millivolt meter. Take the reading at

 

 

TH-TP&TPterminals of the gas valve. The meter should read 325

 

 

millivolts minimum, while holding the valve knob depressed in the

 

 

pilot position, with the pilot lit, and the ON/OFF switch in the OFF

 

 

position. Replace the faulty thermopile if the reading is below the

 

 

specified minimum.

 

 

With the pilot in the ON position, disconnect the thermopile leads

 

 

from the valve. Take a reading at the thermopile leads. The read-

 

 

ing should be 325 millivolts minimum. Replace the thermopile if the

 

 

reading is below the minimum.

 

 

 

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

29

Troubleshooting (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

3. Continued

c. Defective valve.

Turn the valve knob to the ON position. Place the

 

 

ON/OFF switch in the ON position. Check the millivolt

 

 

meter a the thermopile terminals. The millivolt meter

 

 

should read greater than 125mV. If the reading is ac-

 

 

ceptable, and if the burner does not come on, replace

 

 

the gas valve.

 

 

 

 

d. Plugged burner orifice.

Check the burner orifice for stoppage. Remove stop-

 

 

page.

 

 

 

 

e. Wall switch or wires are defective.

Follow the corrective action in Symptom and Pos-

 

 

sible Cause 1.a above. Check the switch and wiring.

 

 

Replace where defective.

 

 

 

4. Frequent pilot outage

a. Pilot flame may be too high or too low, or blow-

Clean thermocouple and adjust the pilot flame for

problem.

ing out (high pressure), causing pilot safety to drop

maximum flame impingement. Follow lighting instruc-

 

out.

tions carefully.

 

 

 

5. The pilot and main

a. No LP in tank.

Check the LP (propane) tank. Refill the fuel tank.

burner extinguish while

 

 

b. Inner vent pipe leaking exhaust gases back into

Check venting system for damage. Replace/repair

in operation.

the system.

improperly assembled pipe sections.

 

 

 

 

 

c. Glass too loose and air tight packet leaks in

Replace glass panel assembly.

 

corners after usage.

 

 

 

 

 

d. Bad thermopile or thermocouple.

Replace if necessary.

 

 

 

 

e. Improper vent cap installation.

Check for proper installation and freedom from debris

 

 

or blockage.

 

 

 

6. Glass soots.

a. Flame impingement.

Adjust the log set so that the flame does not exces-

 

 

sively impinge on it.

 

 

 

 

b. Improper air shutter setting.

Adjust the air shutter located on the control panel.

 

 

 

 

c. Debris around air shutter.

Inspect the opening at the base of the burner. NO MA-

 

 

TERIAL SHOULD BE PLACED IN THIS OPENING.

 

 

 

7. Flame burns blue

a. Insufficient oxygen being supplied.

Ensure that the vent cap is installed properly and free

and lifts off burner.

 

of debris. Ensure that the vent system joints are tight

 

 

and have no leaks.

 

 

Ensure that no debris has been placed at the base of,

 

 

or in the area of the air holes in the center of the base

 

 

pan beneath the burner.

 

 

Ensure that the glass is tightened properly on the unit,

 

 

particularly on top corners.

 

 

 

30

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

14 Maintaining and Servicing Appliance

A. Maintenance Tasks

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

Turn off gas.

Turn off electricity to appliance.

Disable remote control, if one is present.

Ensure appliance is completely cooled.

After servicing:

Replace any screen or barrier that was removed.

Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

Condition of doors, surrounds and fronts.

Condition of glass, glass assembly and glass seal.

Obstructions of combustion and ventilation air.

Condition of logs.

Condition of firebox.

Burner ignition and operation.

Burner air shutter adjustment

Gas connections and fittings.

Obstructions of termination cap.

Clean:

• Glass

Air passageways, grilles, control compartment

Burner, burner ports

Risk of:

Fire

Delayed ignition or explosion

Exposure to combustion fumes

Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial3-4hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when hot.

Turn off appliance after 3-4hours of operation and ALLOW TO COOL.

Remove and clean glass assembly.

Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

31

Inspect

 

Maintenance Tasks

 

 

 

Doors, Surrounds

1.

Assess condition of screen and replace as necessary. Recommend addition of screen if one is not present.

and Fronts

 

 

2.

Inspect for scratches, dents or other damage and repair as necessary.

 

 

 

 

 

3.

Verify no obstructions to airflow through the louvers.

 

 

 

 

4.

Verify maintenance of proper clearance to combustible household objects.

 

 

 

Gasket Seal, Glass

1.

Inspect gasket seal and its condition.

Assembly and Glass

 

 

2.

Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.

 

 

 

 

 

3.

Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

4.

Verify that latches engage properly, clip studs are not stripped, and glass attachment components are

 

 

intact and operating properly. Replace as necessary.

 

5.

Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.

 

 

 

Valve Compartment

1.

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw

and Firebox Top

 

tips that have penetrated the sheet metal are sharp and should be avoided.

 

 

 

 

2.

Remove any foreign objects.

 

 

 

 

3.

Verify unobstructed air circulation.

 

 

 

Logs

1.

Inspect for broken, damaged, or missing logs. Replace as necessary.

 

 

 

 

2.

Verify correct log placement and no flame impingement causing sooting. Correct as necessary.

 

 

 

Firebox

1.

Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.

 

 

 

 

2.

Replace appliance if firebox has been perforated.

 

 

 

Burner Ignition and

1.

Verify burner is properly secured and aligned with pilot or igniter.

Operation

 

 

2.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

 

 

 

 

 

3.

Replace ember materials with new dime-sizeand shape pieces. Do not block ports or obstruct lighting paths.

 

 

 

 

4.

Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.

 

 

 

 

5.

Inspect for lifting or other flame problems.

 

 

 

 

6.

Verify air shutter is clear of dust and debris.

 

 

 

 

7.

Inspect orifice for soot, dirt or corrosion.

 

 

 

 

8.

Verify manifold and inlet pressures. Adjust regulator as required.

 

 

 

 

9.

Inspect pilot flame strength. Clean or replace orifice as necessary.

 

 

 

 

10.

Inspect thermocouple/thermopile for soot, corrosion and deterioration. Clean with emery cloth or replace

 

 

as required.

 

 

 

11. Verify millivolt output. Replace as necessary.

 

 

 

Venting

1.

Inspect venting for blockage or obstruction such as bird nests, leaves, etc.

 

 

 

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

 

 

 

3.

Verify that termination cap clearance to subsequent construction (building additions, decks, fences or

 

 

sheds) has been maintained.

 

 

 

 

4.

Inspect for corrosion or separation.

 

 

 

 

5.

Verify weather stripping, sealing and flashing remains intact.

 

 

 

 

6.

Inspect draft shield to verify it is not bent, damaged or missing.

 

 

 

Remote controls

1.

Verify operation of remote.

 

 

 

 

2.

Replace batteries in remote transmitters and battery-poweredreceivers.

 

 

 

 

3.

Verify batteries have been removed from battery back-upIPI systems to prevent premature battery failure

 

 

or leaking.

32

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

15 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

A

B

C

LM

N

K

O

J

D

E

F

G

I

 

 

 

H

GAS INLET

 

ELECTRICAL

 

ACCESS

P

 

T

Q

 

 

R

 

U

 

 

S

 

 

MODEL DIMENSIONS

LOCATION

MTL-INSERT

 

 

Inches

Millimeters

 

 

 

 

A

29-1/32

737

B

20-5/32

512

C

10-3/32

256

D

32-5/16

821

E

26-11/16

678

F

11-5/8

296

G

22-23/32

577

H

20-7/16

519

I

21-1/8

537

J

8-7/16REF

215

MODEL DIMENSIONS

LOCATION

MTL-INSERT

 

 

Inches

Millimeters

 

 

 

 

K

2-5/16

58

L

4-7/16

112

M

5-5/32

131

N

2-5/32

55

O

13-23/32

348

P

2-1/2

64

Q

5-9/32

135

R

8-29/32

227

S

14-11/16

373

T

2-9/16

65

 

 

 

U

6-1/16

154

Figure 15.1 Appliance Dimensions

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

33

B. Vent Kits Components

Direct Vent Flex Liner Kits (see Figure 15.2)

LINK-DV-30B or(LINK-DV-30):Masonry 3 inch flex liner kit. Expands to 30 feet. Includes: two liners, termination cap, flashing, and link adapter.

LINK-DV4-30B or(LINK-DV4-30):Masonry 3 inch flex liner kit. Expands to 30 feet and 4 feet respectively. Includes: two liners, termination cap, flashing, and link adapter.

LINK-DV30B

LINK-DV4-30B

Installation

Installation

TERMINATION

CAP

EXHAUST

AIR

VENT PIPE

WARNING:

DO NOT BLOCK

THIS PIPE END!

INLET AIR

VENT PIPE

OPTIONAL LINK-ZC-ADPB

FOR USE WITH CLASS A

WOODBURNING PIPE

Figure 15.2 Direct Vent Flex Liner Kits

Direct Vent Flex Liner Accessory Kits (see Figure 15.3)

Flash-Damp:Zero clearance damper flashing kit for use withLINK-DV-30B orLINK-DV4-30B liner kits.

LINK-ZC-ADP:Zero clearance chimney adapter

SVRLINK-ADP:Adapter kit (colinear to coaxial 3 inches included in above kits).

FLEX3-30:One 3 inch flexible liner expands to 30 feet.

FLEX3-30/2:Two 3 inch flexible liners expands to 30 feet each.

FLEX-CNCT:Connector kit - 3 inch liner to 3 inch liner, one connector per kit.

FLASH-DAMP

LINK-ZC-ADP

SVRLINK-ADP

FLEX3-30

FLEX3-30/2

FLEX3-CNCT

Figure 15.3 Direct Vent Flex Liner Accessory Kits

34

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

C. Service Parts

MTL-INSERT

Service Parts Diagram

Beginning Manufacturing Date: Oct. 2007

 

Ending Manufacturing Date: ______

7

8

9

10

11

17

14

12

13

16 15

Log Set Assembly

 

4

5

1

6

 

 

3

2

 

 

 

 

 

Part number list on following page.

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

35

 

 

Service Parts

 

MTL-INSERT

 

 

 

 

 

 

 

 

 

 

Service Parts Diagram

 

 

 

 

 

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

 

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

 

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Log Set Assembly

 

LOGS-SXT

Y

1

Log 1

 

SRV349-701

 

2

Log 2

 

SRV349-702

 

3

Log 3

 

SRV327-703

 

4

Log 4

 

SRV349-704

 

5

Log 5

 

SRV327-705

 

6

Log 6

 

SRV349-706

 

7

Termination Assembly

 

319-213A

 

8

Burner NG, LP

 

349-176A

Y

9

Heat shield

 

349-150

 

10

Grate Assembly

 

327-360A

 

11

Base Pan

 

349-124

 

12

Control Panel

 

319-129

 

13

Piezo Ignitor

 

219-513

Y

14

Glass Door Assembly

 

GLA-349

Y

15

Extension Knob Hi / Lo

 

571-533

Y

16

Extension Knob On / Off

 

571-534

Y

17

Cover Plate

 

060-219

 

 

 

 

 

 

 

Blower (Optional)

 

GFK-160A

 

 

Flex Pipe Handle

 

438-351

 

 

Glass Latch Assembly

 

386-122A

Y

 

Grommet ( Req for Junction box Installation)

 

100-831

 

 

Junction Box (Req for Blower installation)

 

040-250A

Y

 

Mineral Wool

 

050-721

 

 

Pilot Tube

 

SRV485-301

Y

 

Thermocouple

 

2103-511

Y

 

Thermopile

 

2103-512

Y

 

Touch Up Paint

 

203-9

 

 

Conversion Kit NG

NGKS-SXT

Y

 

Conversion Kit LP

LPKS-SXT

Y

 

Pilot Orifice NG

2103-116

Y

 

Pilot Orifice LP

2103-117

Y

 

Regulator NG

230-1570

Y

 

Regulator LP

230-1520

Y

Additional service part numbers appear on following page.

36

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

Service Parts

 

MTL-INSERT

Valve Assembly Parts List

 

Beginning Manufacturing Date: Oct. 2007

 

 

 

 

Ending Manufacturing Date: ______

Standing Pilot Valve Assembly

1

 

 

 

 

2

 

 

 

 

4

3

 

 

 

 

 

 

 

 

 

 

15

 

 

 

13

14

 

 

 

 

 

5

 

 

 

7

6

 

 

 

 

 

 

 

9

8

 

 

12

 

 

 

 

10

 

 

 

 

11

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

1

Pilot Assembly NG

 

2103-010

Y

Pilot Assembly LP

 

2103-011

Y

 

 

2

Pilot Bracket

 

319-164

 

3

Shutter Bracket Assembly

 

2026-130

Y

4

Orifice NG (#35C)

 

582-835

Y

Orifice LP (#52C)

 

582-852

Y

 

 

5

Shutter Arm, Top

 

319-170

 

6

Shutter Arm, Bottom

 

319-168

 

7

L Bracket

 

319-120

 

8

Valve Bracket

 

319-146

 

9

Flexible Gas Connector

 

477-301A

Y

10

Valve NG

 

230-0710

Y

Valve LP

 

230-0720

Y

 

 

11

Flex Ball Valve Assembly

 

531-320A

Y

12

Gasket, Valve Plate

 

319-401

 

13

Bracket, Burner Support

 

319-166

 

14

Burner Neck

 

319-336

 

15

Gasket, Burner Neck

 

319-400

 

 

Wiring Assembly

 

2020-069

Y

 

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

 

37

D. Limited Lifetime Warranty

Hearth & Home Technologies LIMITED WARRANTY

Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

 

 

 

 

 

 

 

Components Covered

Parts

Labor

Gas

Wood

Pellet

EPA

Electric

 

Venting

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All Parts and Material Except as

1 Year

X

X

X

X

X

 

X

covered by Conditions, Exclusion,

 

 

 

 

 

 

 

 

 

and Limitations listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

 

 

 

Igniters, Electronic Components,

 

 

 

 

 

 

 

and Glass

2 years

 

 

 

 

 

 

 

X

X

X

X

 

 

 

Blowers

 

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded Refractory Panels

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots

 

 

 

 

 

 

 

 

 

 

5 years

3 years

 

 

X

X

 

 

 

Castings & Baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Firebox, HHT Chimney,

7 years

3 years

 

X

X

X

 

 

 

Termination & Heat

 

 

 

 

 

 

 

 

 

Exchanger

 

 

 

 

 

 

 

 

 

 

10 years

1 year

X

 

 

 

 

 

 

Burners, Logs & Refractory

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

1 year

X

 

 

 

 

 

 

Firebox & Heat Exchanger

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

 

X

All Replacement Parts

 

 

 

 

 

 

 

 

See Conditions, Exclusions, and limitations.

9-01-08

 

 

 

 

 

 

 

 

 

 

CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY

This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation.

The maximum amount recoverable under this warranty is limited to the purchase price of the product.

In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.

Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home is not covered under this warranty.

Page 1 of 2

4021-645A09-01-08

38

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

D. Limited Lifetime Warranty (continued)

This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered by this warranty.

Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this noise are not covered by this warranty.

HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identification label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those specified in the operating instructions; (6) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; and/or (7) modification of the appliance not expressly authorized and approved by HHT in writing.

This warranty does not apply to non-HHTventing components, hearth components or other accessories used in conjunction with the installation of this product.

This warranty is void if the appliance has been over-firedor operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.

Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE WARRANTY SPECIFIED ABOVE.

This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all warranties currently in existence.

If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HHT dealer or supplier.

Page 2 of 2

4021-645A09-01-08

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08

39

E. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Printed in U.S.A. - Copyright 2008

40

Heat & Glo • MTL-Insert2145-900Rev. F • 9/08