Heat & Glo LifeStyle LCOR-HV-IPI User Manual

Size:
3.29 Mb
Download

Service Parts List (NG, LP)

RCOR-HV-IPI

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.

 

 

 

 

 

AVAILABLE

 

 

 

 

 

TO SHIP IN 24

 

 

 

 

 

HOURS

ITEM

 

COMMON PARTS

SERIAL #

PART NUMBER

Î

 

 

 

 

 

 

 

 

Burner Orifice NG (#32DMS)

 

582-832

Y

 

 

 

 

 

 

 

 

Burner Orifice LP (#50DMS)

 

582-850

Y

 

 

 

 

 

 

1

 

End Glass Assembly

 

GLA-MS

Y

 

 

 

 

 

 

2

 

Glass Door Assembly

 

GLA-6TROC

Y

 

 

 

 

 

 

3

 

Burner Assembly

 

2005-006

Y

 

 

 

 

 

 

4

 

Log Grate

 

2005-012

 

 

 

 

 

 

 

5

 

Side Refractory

 

SRV2005-730

 

 

 

 

 

 

 

6

 

Refractory, Back

 

SRV2005-731

 

 

 

 

 

 

 

7

 

Log Set Assembly

 

LOGS-MSR

Y

 

 

 

 

 

 

8

 

Log 1

 

SRV2005-701

 

 

 

 

 

 

 

9

 

Log 2

 

SRV2005-700

 

 

 

 

 

 

 

10

 

Log 3

 

SRV2005-702

 

 

 

 

 

 

 

11

 

Log 4

 

SRV2005-703

 

 

 

 

 

 

 

12

 

Log 5

 

SRV2005-704

 

 

 

 

 

 

 

13

 

Log 6

 

SRV2005-705

 

 

 

 

 

 

 

14

 

Log 7

 

SRV703-703

 

 

 

 

 

 

 

 

 

Lava Rock Bag

 

2005-790

 

 

 

 

 

 

 

 

 

Flue Restrictor

 

385-128

 

 

 

 

 

 

 

 

 

Teco-Sil,5 lb. bag

 

700-790

 

 

 

 

 

 

 

 

 

Ember Mesh Assembly

 

2006-008

Y

 

 

 

 

 

 

 

 

Non-CombustibleBoard (side)

 

2006-136

 

 

 

 

 

 

 

 

 

Non-CombustibleBoard (end)

 

2008-114

 

 

 

 

 

 

 

 

 

Junction Box

 

4021-013

Y

 

 

 

 

 

 

 

 

3V Adaptor Plug

 

593-593A

Y

 

 

 

 

 

 

 

 

Battery Pack

 

593-594A

Y

 

 

 

 

 

 

 

 

Fiberglass Rope

 

060-455

 

 

 

 

 

 

 

 

 

Glass Latch Support Assembly

 

386-122A

Y

 

 

 

 

 

 

 

 

Mineral Wool

 

050-721

 

 

 

 

 

 

 

 

 

Conversion Kit NG

 

NGK-MS

Y

 

 

Conversion Kit LP

 

LPK-MS

Y

 

ACCESSORIES

 

 

 

 

 

Fan Kit

 

GFK-160A

 

 

 

Remote Control Kit

 

RC-SMART-HNG

 

 

 

Remote Control Kit

 

SMART-STAT-HNG

 

 

 

Remote Control - Multi-functional

 

RCT-MLT-HNG

 

 

 

Wall Switch, Multi-functional

 

WSK-MLT

 

 

 

Plug Adapator Kit (for WSK-MLT)

 

PLUG-ADP

 

 

 

Louvers with Mesh

 

MS-LOUVERS

 

 

 

Louvers with Mesh - End Panel

 

MS-LOUVERS-EP

 

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

11

Service Parts

PIER-HV-IPI,ST-HV-IPIL&RCOR-HV-IPI

(NG, LP) Exploded Parts Diagram

Beginning Manufacturing Date: 6-03

 

Ending Manufacturing Date: ______

13

14

9

8

7

10

11

12

 

1

 

 

6

 

 

 

 

 

 

 

 

 

2

3

4

5

 

 

 

 

 

 

 

 

AVAILABLE TO

 

 

 

 

 

 

SHIP IN 24

 

 

 

 

 

 

HOURS

ITEM

DESCRIPTION

 

SERIAL #

PART NUMBER

 

1

ON/OFF Rocker Switch

 

 

 

060-511

Y

2

ON/OFF Wire Assembly

 

 

 

060-521A

Y

3

Valve NG

 

 

 

750-500

Y

3

Valve LP

 

 

 

750-501

Y

4

Flexible Gas Connector

 

 

 

2005-009

Y

5

Module

 

 

 

593-592

Y

6

Wire Assembly

 

 

 

593-590A

Y

7

Ember Box Assembly

 

 

 

2005-114

Y

8

Pilot Assembly NG

 

 

 

385-510A

Y

8

Pilot Assembly LP

 

 

 

385-511A

Y

9

Pilot Bracket

 

 

 

2005-118

 

10

Gasket Orifice

 

 

 

2005-166

 

11

Valve Bracket

 

 

 

2005-120

 

12

Flex Ball Valve Assembly

 

 

 

302-320A

Y

13

Pilot Assembly Support

 

 

 

385-120

 

14

Ground Strap

 

 

 

385-512

 

 

Regulator, NG

 

 

 

NGK-DXV

Y

 

Regulator, LP

 

 

 

LPK-DXV

Y

 

Pilot Tube

 

 

 

446-301

Y

 

Orifice Spud NG

 

 

 

446-505

Y

 

Orifice Spud LP

 

 

 

446-517

Y

NOTE: Replacement bulbs to be supplied by homeowner. Recommended replacements: Sylvania Mini Candelabra 75 watts.

12

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

1Approvals and Codes

Appliance Certification

The Heat & Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories.

Certification

MODELS: PIER-HV-IPI,ST-HV-IPI,LCOR-HV-IPI,RCOR-HV-IPI

LABORATORY: Underwriters LaboratoriesTYPE: Direct Vent Gas Fireplace HeaterSTANDARD: ANSI Z21.88•CGA2.22•UL307B

Installation Codes

The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you are in compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGA-B149Installation Codes (in Canada). The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes with the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the CSAC22.1 Canadian Electric Code (in Canada).

These models may be installed in a bedroom or bed-sittingroom in the U.S.A. and Canada.

High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2,000 feet in the U. S. A. and in Canada.

When installing this appliance at an elevation above 2,000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A. or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4,500 feet (in Canada), check with local authorities.

Heat & Glo Quality Systems registered by SGS ICS

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

13

NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.

G.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be ProductApproved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

14

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

2Getting Started

Introducing the Heat & Glo Gas Fireplaces

Heat & Glo direct vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems. Gas fireplace diagrams, including the dimensions, are shown in this section.

Pre-installPreparation

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass.Do not install any unit with damaged, incomplete, or substitute parts.

The vent system components are shipped in separate packages. The gas logs are packaged separately and must be field installed.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and may present a fire hazard.

The Heat & Glo Warranty will be voided by, and Heat & Glo disclaims any responsibility for, the following actions:

Installation of any damaged fireplace or vent system component.

Modification of the fireplace or direct vent system.

Installation other than as instructed by Heat & Glo.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not manufactured and approved by Heat & Glo, not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, it’s necessary to determine:

Where the unit is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

15

 

5-1/4

 

 

 

 

(133mm)

 

 

 

 

 

1/2

 

 

 

 

 

(13mm)

 

 

 

 

 

12

 

 

 

 

(306mm)

 

 

 

 

 

Ø8

 

 

 

 

 

(205mm)

 

 

 

12

Ø8

 

42-5/8

 

 

(305mm)

 

(1082mm)

 

 

 

(205mm)

 

 

 

 

 

ELECTRICAL

 

 

 

 

 

ACCESS

 

 

 

 

 

 

 

32-5/16

 

 

 

 

42

(820mm)

 

21-9/16

34-3/4

GAS LINE

(1067mm)

21-9/16

 

(547mm)

ACCESS

 

 

 

(883mm)

 

(547mm)

 

 

 

 

 

 

4-1/16

2-5/16

 

 

17-15/16

 

(58mm)

 

 

 

(102mm)

 

37-7/16

(455mm)

 

 

 

 

 

 

 

 

 

 

 

 

(950mm)

24

 

4-1/2

4-3/4

 

 

 

 

 

(610mm)

 

(114mm)

(121mm)

 

 

 

 

 

 

 

TOP VENT

 

 

 

 

 

COLLARS

 

TOP STANDOFFS

 

 

 

 

 

 

 

 

 

 

 

 

REAR VENT

 

 

 

 

 

COLLARS

 

 

 

 

SIDE GLASS

 

 

GAS CONTROLS

 

DOOR

 

 

 

& LABELS

 

 

GAS LINE

 

 

 

 

 

 

 

 

 

 

ACCESS

 

 

 

 

 

ELECTRICAL

 

 

 

 

 

ACCESS

 

Figure 1. Diagram of the PIER-HV-IPI

 

 

 

16

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

 

 

 

 

5-14

 

 

 

 

 

(133mm)

 

 

 

 

 

1/2

 

 

 

 

 

(13mm)

 

 

 

 

 

(4)

 

 

 

 

12

 

 

 

 

 

(306mm)

 

 

 

 

 

Ø8

 

 

 

 

 

(205mm)

 

 

 

 

 

12

 

 

 

 

 

(305mm)

 

 

 

 

 

Ø8

46-5/8

 

 

 

 

(205mm)

(1183mm)

 

 

 

 

ELECTRICAL

 

 

 

 

 

ACCESS

 

 

 

 

 

 

32-5/16

 

 

34-3/4

 

42

(821mm)

4-1/2

 

 

 

(114mm)

 

(882mm)

 

(1067mm)

21-9/16

 

 

 

 

GAS LINE

(548mm)

 

 

 

 

ACCESS

 

 

 

 

 

 

 

 

 

 

8-1/2

 

 

 

 

 

(216mm)

 

 

4-1/16

 

2-5/16

36-3/16

24

 

 

(58mm)

(919mm)

(610mm)

2-9/16

(102mm)

 

 

 

 

(64mm)

4-1/2

 

4-3/4

 

 

 

(114mm)

 

(121mm)

 

 

 

 

TOP VENT

 

 

 

 

COLLARS

 

 

 

 

 

TOP STANDOFFS

 

REAR VENT

 

 

 

 

 

 

 

 

 

 

COLLARS

 

 

 

GAS CONTROLS

SIDE GLASS

 

 

 

 

& LABELS

DOOR

 

 

 

 

 

 

GAS LINE

 

 

 

 

 

ACCESS

 

 

 

 

 

ELECTRICAL

 

 

 

 

 

ACCESS

 

Figure 2.

Diagram of the ST-HV-IPI

 

 

 

 

 

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

 

17

 

 

1/2

 

 

 

5-1/4

(13mm)

 

 

 

(4)

 

 

 

(133mm)

 

 

 

 

Ø8

 

 

 

 

(205mm)

 

 

 

 

12-1/16

 

 

 

 

(306mm)

 

 

 

 

12

 

 

 

Ø8

(305mm)

42-5/8

 

17-15/16

 

 

(205mm)

 

 

 

(1083mm

 

(455mm)

 

 

 

 

ELECTRICAL

 

 

 

 

ACCESS

 

 

 

 

GAS LINE

 

 

 

 

ACCESS

 

 

 

34-3/4

 

 

21-9/16

 

(882mm)

 

 

21-9/16

2-9/16

 

(548mm)

 

 

(547mm)

 

(64mm)

 

42

 

 

 

 

2-5/16

 

(1067mm)

 

 

 

 

 

 

(58mm)

 

 

 

10

 

32-5/16

 

 

(254mm)

 

 

24-1/8

 

(821mm)

 

 

 

 

(612mm)

 

 

 

 

7-1/4

 

37-7/16

 

 

(184mm)

 

 

29-1/4

 

(950mm)

 

4-3/4

 

 

 

(743mm)

 

 

 

 

(121mm)

 

 

 

TOP VENT

 

TOP STANDOFFS

 

 

COLLARS

 

 

 

 

 

 

 

 

REAR VENT

 

 

 

 

COLLARS

SIDE GLASS

 

 

 

 

DOOR

 

 

 

 

 

 

END GLASS

 

GAS LINE

 

 

DOOR

 

 

 

 

ACCESS

 

GAS CONTROLS

 

 

 

 

 

 

 

& LABELS

 

 

ELECTRICAL

 

 

 

 

ACCESS

Figure 3. Diagram of the LCOR-HV-IPIandRCOR-HV-IPI

 

 

18

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

 

3Installing the Fireplace

Step 1. Locating the Fireplace

The diagram below shows space and clearance requirements for locating a fireplace within a room.

Note: Refer to Figure 4B for dimensions and appliance locations if installing a Pier-HV unit with a Catalina shelf and/or marble package.

GLASS

GLASS

 

PIER-HV-IPI

GLASS

RCOR-HV-IPI

TOP VIEW

TOP VIEW

36"

 

 

GLASS

 

GLASS

 

36"

36"

 

36"

 

GLASS

 

36"

ST-HV-IPI

 

GLASS

 

 

TOP VIEW

 

 

GLASS

36"

LCOR-HV-IPI

 

TOP VIEW

36"

GLASS

 

 

 

Figure 4A. Fireplace Dimensions and Locations

Note: Refer to the Catalina installation instruction included with kit for assembly and installation.

Note: This location diagram MUST be followed when installing aPier-HVwith a Catalina shelf/marble package since the fireplace is installed further from finished wall.

FINISHED

WALL

45 -1/4in. (1149mm)

50-1/2in.34-1/2 in.

7 in.

47-1/2in.

13/16 in.45-1/4in.

Marble sizes (inches):

Header ..................................

26 x 8

Side headers ..................

45-1/2x 8

Legs ................................

33-1/2x 7

Figure 4B.

Fireplace Locations/Dimensions with

 

Catalina Shelf/Marble Package ONLY

Clearance Requirements

The top, back, and sides of the fireplace are defined by stand-offs.The minimum clearance to a perpendicular wall extending past the face of the fireplace is one inch (25 mm). The metal ends of the fireplace mayNOT be recessed into combustible construction.

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06

19

Minimum Clearances

from the Fireplace to Combustible Materials

 

Inches

mm

Glass Sides or Ends

.......... 36 ....................

914

Floor ...................................

0 .......................

0

Rear Vent ...........................

1/2 .....................

13

Metal Sides or Ends ..........

1/2 .....................

13

Top ...................................

2 1/2 ...................

64

Ceiling* ..............................

31 ....................

787

*The clearance to the ceiling is measured from the top of the unit, excluding the standoffs (see Figures 37 & 38).

The distance from the unit to combustible construction is to be measured from the unit outer wrap surface to the combustible construction, NOT from the screw heads that secure the unit together.

Minimum Clearances

from the Vent Pipe to Combustible Materials

 

Inches

mm

Vertical Sections. .............

1 ................

25

Horizontal Sections

 

 

Top .....................................

3 ................

75

Bottom ...............................

1 ................

25

Sides .................................

1 ................

25

At Wall Firestops

 

 

Top ..................................

2 1/2 ............

63.7

Bottom ..............................

1/2 ...............

13

Sides .................................

1 ................

25

For minimum clearances, see the direct vent termination clearance diagrams on pages 31 and 32 in this manual.

Step 2. Framing the Fireplace

Fireplace framing can be built before or after the fireplace is set in place. Framing should be positioned to accommodate wall coverings and fireplace facing material. The diagram below shows framing reference dimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING.

!WARNING: FRAMING DIMENSIONS ASSUME USE OF 1/2 INCH THICK WALL COVERING

MATERIALS ON EXTERIOR OF FRAMING ONLY AND NO SHEETROCK ON INTERIOR OF FRAMING.

20

Heat & Glo • PIER-HV-IPI,ST-HV-IPI,L&R-COR-HV-IPI2005-900Rev. K • 11/06