Heat & Glo LifeStyle II-B User Manual

Size:
2.64 Mb
Download

Para obtener un ejemplar en Español de este Manual del propietario, visite www.heatnglo.com.

Pour demander un exemplaire en français de ce Manuel du propriétaire, visitez www.heatnglo.com.

Owner’s Manual

Installation and Operation

Model:

Twilight-II-B

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard, Title 24 CFR, Part 3280 orStandard for Installation in Mobile Homes, CAN/ CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

Keep children away.

CAREFULLY SUPERVISE children in same room as appliance.

Alert children and adults to hazards of high temperatures.

Do NOT operate with protective barriers open or removed.

Keep clothing, furniture, draperies and other combustibles away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. Do NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts:

installation must be performed by a licensed plumber or gas fitter;

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trainedprofessionals, or technicians supervised by an NFI certified professional.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this Owner’s Manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo LifeStyle Collection gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo LifeStyle Collection gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo LifeStyle Collection gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo LifeStyle Collection family of products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, abrand of Hearth & Home Technologies, Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

Not for usewithsolidfuel.

(Nedoitpasentreutiliseavecuncombustiblesolide).

Typeof Gas(Sorte De Gaz): Thisappliancemustbeinstalledinaccordancewithlocalcodes, ifany;ifnot,followANSIZ223.1intheUSAorCAN/CGAB149 installationcodes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum PermissibleGasSupplyfor PurposesofInputAdjustment.

 

 

 

ApprovedMinimum (De Gaz) Acceptable

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumPressure(Pression)

 

0.0inw.c.

(Po.Col.d’eau)

 

 

 

MaximumManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

Minimum ManifoldPressure(Pression)

0.0inw.c.

(Po.Col.d’eau)

 

 

 

TotalElectricalRequirements: 000Vac,00Hz.,lessthan00Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INCANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN.INPUTBTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICESIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

Table of Contents

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. Thermal Performance Data . . . . . . . . . . . . . . . . . . . . . . . . 4 D. Air Infiltration, Water Resistance and Structural Tests . . . 4 E. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 F. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4 G. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 4 H. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4 I. Requirements for the Commonwealth of Massachusetts. . 5

2 Getting Started

A. Design and Installation Considerations . . . . . . . . . . . . . . . 6

B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6

C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 6

3 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7 B. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 C. Mantel Projections - Indoor only . . . . . . . . . . . . . . . . . . . . 9

4 Termination Locations

A. Appliance Opening Minimum Clearances . . . . . . . . . . . . 10

5 Appliance Preparation

A. Removing Non-combustibleFacing Material Assembly . .11

B. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . .11

C.Installing Non-combustibleFacing Material (Outdoor Side). 14

6 Gas Information

A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

7 Electrical Information

A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 17 B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 17 C. Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 D. Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 19 E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 20 F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 20

8 Finishing

A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

9 Appliance Setup

A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 24

B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

D. Lava Rock and Ember Placement . . . . . . . . . . . . . . . . . . 24

E. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

F. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

G. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

H. Shutter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

10 Operating Instructions

A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 28 B. Lighting Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 C. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 30

11 Troubleshooting

A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 31

12 Maintaining and Servicing Appliance

A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

13 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 35

B. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

C. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 39

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Î = Contains updated information.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

3

1 Listing and Code Approvals

A. Appliance Certification

MODEL: Twilight-II-B

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance

STANDARD: ANSIZ21.50-2003CSA2.22-M03• UL307B

This product is listed to ANSI standards for “Vented Gas Appliances” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with theNational Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and theCAN/CGA B149 Installation Codes in Canada.

C. Thermal Performance Data

Model: Twilight-II-B

Sound Transmission

Thermal Resistance

Thermal Conductivity

Class (STC)

(R Value)

(K Value)

27

0.08hr-sqft-ºF/BTU

12.5 BTU-in/hr-sqft-ºF

D. Air Infiltration, Water Resistance and Structural Tests

The Hearth & Home Technologies Twilight-II-BIndoor/ Outdoor Appliance unit was tested to the following ASTM standards at the Stork Twin City Testing laboratory.

Air infiltration test ASTM:E283-(04).The sample was tested at 1.57 psf (equivalent to a25-mphwindload).

Water resistance test ASTM:E331-00.The test specimen was tested at the requested test pressures of 8.0 & 25.0 psf.

Structural test ASTM:E330-02.The unit was tested to a design pressure of50-psf,a test pressure of75-psf.

Test Results

Model

Air Infiltration

Water Resistance

Structural Load

(ASTM E283)

(ASTM E331)

(ASTM E330)

 

 

 

 

 

Twilight-II-B

0.07CFM/ft2

No leakage

No Blowout

Indoor/Outdoor

 

@ 8psf & 25psf

@ 75psf

E. BTU Specifications

Model

 

Input BTU/h

Orifice Size

U.S. (0-2000FT) or Canada(2000-4500FT)

(DMS)

 

Twilight-II-B(NG)

US

38,000

32

CAN

34,200

33

 

Twilight-II-B(LP)

US

37,000

50

CAN

33,300

51

 

F. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

G. Non-CombustibleMaterials Specification

Material which will not ignite and burn are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof. Materials that are reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at

750oC, shall be considerednon-combustiblematerials.

H. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

4

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

I.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

5

2 Getting Started

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

The Twilight-II-Bhas been carefully engineered to provide a unique fireplace experience. Since it is different than any other product on the market, care must be taken when installing this appliance so that our customer does not experience undesirable performance or conditions.

1.Install the appliance according to this Owner’s Guide paying particular attention to flashing and sealing instructions.

2.In the cold northern climates pay attention to exposures and prevailing wind conditions when locating the appliance, the same as you would for locating exterior windows and doors.

The Twilight-II-Bhas the thermal characteristics of a high quality window system. Temperatures near the appliance will be cooler than what is realized with a fully insulated wall.

Operation of the appliance will eliminate any cool drafts and will provide the room with a comfortable ambiance.

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning an appliance installation, it’s necessary to determine the following information before installing:

Where the appliance is to be installed. See Section 3.

Gas supply piping. See Section 6.

Electrical wiring. See Section 7.

Framing and finishing details. See Sections 3 and 8.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.See Section 9.

WARNING

Keep appliance dry.

• Mold or rust may cause odors.

• Water may damage controls.

B. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw

Framing material

Pliers

Hi temp caulking material

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Manometer

Voltmeter

Tape measure

Level

Non-corrosiveleak check solution

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews One 1/4 inch female connection (for optional fan)

C. Inspect Appliance and Components

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

• Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components. Report damaged parts to dealer.

Carefully remove the appliance and components from the packaging.

Remove and keep outdoor flashing header from pallet by removing two fasteners.

The gas logs may be packaged separately and must be field installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

6

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

3 Framing and Clearances

NOTE:

Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

Illustrations/diagrams are not drawn to scale.

Actual installation may vary due to individual design preference.

A.Selecting Appliance Location

When selecting a location for your appliance it is important to consider the required clearances to walls (see Figure 3.1).

WARNING

Fire Risk

Provide adequate clearance:

Around air openings

To combustibles

• For service access

Locate appliance away from traffic areas.

NOTE: For actual appliance dimensions refer to Section 13.

GLASS

FLUSH TO EXTERIOR INSULATED ENVELOPE

 

B

 

 

 

 

 

GLASS

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In addition to these framing dimensions, also reference the following section:

• Clearances and Mantel Projections (Sections 3.B and 3.C)

D

 

E

GLASS

B

C

GLASS

 

 

 

 

 

 

FLUSH TO EXTERIOR INSULATED ENVELOPE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

B

C

 

 

D

E

 

 

Minimum

Minimum

-

 

 

Minimum

-

 

Inches

43

1/2

24

 

 

36

43

 

Millimeters

1092.2

12.7

609.6

 

 

914.4

1092.2

 

Figure 3.1 Appliance Locations

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

7

B. Clearances

WARNING

Fire Risk.

Odor Risk.

Install appliance on hard metal or wood surfaces extending full width and depth of appliance.

Do NOT install appliance directly on carpeting,

vinyl, tile or any combustible material other than wood.

WARNING

Fire Risk.

Do not install appliance against vapor barriers or exposed insulation.

• Prevent contact with sagging or loose insulation.

WARNING

Fire Risk.

Locate and install appliance to all clearance specifications in manual.

OVERHANG

A

SIDING

A

B

 

 

 

A

SIDING

 

 

SIDING

 

Vinyl

Non-vinyl

A

36 in.

12 in.

B

64-5/16in.

35-5/16in.

Figure 3.2 Exterior View - Minimum Clearances

Í

Note: Framing dimensions assume use of 1/2 inch thick wall covering materials on exterior of framing only,

and NO sheetrock on interior of framing.

C

A

EXTERIOR

FRAMING

D

E

INTERIOR FRAMING

B

From top of hood to ceiling (interior) or F

overhang (exterior).

J

G

I

H

K

CLEARANCES TO COMBUSTIBLES:

 

A

B

C

D

E

 

F

 

G

H

I

J

K

 

Exterior

Interior

Rough

Rough

Framing

Clearance

Clearance to Overhang

 

 

Standoff

Standoff

 

 

Rough

Rough

for non-

Combustible

Combustible

Sides of

 

(EXT)

 

 

Opening

Opening

Opening

Opening

combustible

to Ceiling

 

Floor

Flooring

Height

Height

Appliance

 

(Depth)

(Width)

(INT)

 

 

 

Inside

Outside

 

Non-Vinyl

 

Vinyl

 

(Height)

(Height)

 

 

material

 

 

 

 

 

 

 

Inches

47-1/4

41-1/4

23

44

66-1/8

35-3/4

35-5/16

 

64-5/16

0

0

3-3/8

9-1/2

1/2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

1200

1048

584

1118

1680

908

897

 

1634

0

0

86

241

13

Figure 3.3 Clearances to Combustibles

8

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

C. Mantel Projections - Indoor only

CEILING

NON-COMBUSTIBLEBOARD

(SUPPLIED ON APPLIANCE)

INDOOR SIDE ONLY

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

10

11

 

 

 

35-3/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

8

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-5/8

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

12-

 

5/8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11-5/8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10-5/8

 

 

 

 

 

 

 

 

8-

9-

 

5/8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5/8

 

 

 

 

 

 

 

 

 

 

HOOD

 

 

 

 

 

 

 

 

 

 

 

 

 

7-5/8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Measurements are in inches.

Figure 3.4 Indoor Clearances to Mantels or other Combustibles above Appliance

TOP VIEW

MEASURED

FROM CORNER

½ IN.

FIREPLACE

HOOD

Figure 3.5 Indoor clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.)

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

9

4 Termination Locations

A. Appliance Opening Minimum Clearances

WARNING

Fire Risk. Explosion Risk.

Maintain vent termination minimum clearances as specified.

= AREA WHERE APPLIANCE IS NOT PERMITTED

D

E

B

L

B

FP

F FP

 

FP

G

 

 

X = AIR SUPPLY INLET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

H

 

FP

= APPLIANCE OPENING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M

 

 

 

 

 

 

 

 

P

FP

B

 

 

 

 

 

R

N

 

 

 

 

 

FP

 

 

 

 

 

 

 

 

FP

 

 

I

M

FP

X

Q

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

J or K

(See Note 2)

 

 

 

 

 

 

 

A

=

0”...........................

clearances above grade, veran-

 

 

(See Note 1)

da, porch, deck or balcony

B*

=

12”.........................

clearances to window or door

 

 

 

that may be opened, or to per-

 

 

 

manently closed window.

D

=

 

vertical clearance to ventilated

35-5/16” (non-vinyl)

 

 

64-5/16”(vinyl)

soffit located above the hood

 

 

 

within a horizontal distance of 2

 

 

 

feet (60 cm) from the center-line

 

 

 

 

 

 

of the hood

E

=

35-5/16” (non-vinyl)

.. .clearance to unventilated soffit

 

 

64-5/16”(vinyl)

 

F

=

9”..........................

clearance to outside corner

G*

=

12”.........................

clearance to inside corner

H

=

3 ft. (Canada) ........

not to be installed above a gas me-

 

 

 

ter/regulator assembly within 3 feet

 

 

 

(90cm) horizontally from the center-

 

 

 

line of the regulator

I

=

3 ft. ........................

clearance to service regulator vent

 

 

 

outlet and electric service

*36” minimum for vinyl windows or vinyl siding.

**a appliance shall not open directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

***only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor, or if the screened porch guidelines are followed.

NOTE 1: Local codes or regulations may require different clearances.

NOTE 2: Termination in an alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions specified for vinyl ornon-vinylsiding and soffits.1. There must be 3 feet minimum between terminations or between the appliance and termination.2. All mechanical air intakes within 10 feet of a termination must be a minimum of 3 feet below the appliance hood.3. All gravity air intakes within 3 feet of the appliance hood must be a minimum of 1 foot below the termination.

Figure 4.1 Minimum Clearances for Appliance Opening

J

=

9” (U.S.A.)

 

 

 

 

 

 

 

12” (Canada)...........

clearance to non-mechani-

 

 

 

 

cal air supply inlet to building

 

 

 

 

or the combustion air inlet to

 

K

=

3 ft. (U.S.A.)

any other appliance

 

 

 

 

 

 

 

 

6 ft. (Canada)...........

clearance

to a mechanical

 

 

 

 

air supply inlet

 

L**

=

54”...........................

clearance above paved side-

 

 

 

(See Note 1)

walk or a paved driveway lo-

 

 

 

 

cated on public property

 

M***=

35-5/16”...................

clearance

under veranda,

 

 

 

 

porch, deck, balcony or over-

 

 

 

 

hang

 

 

 

 

 

64-5/16” ..................

vinyl

 

 

 

N

=

12” ..........................

non-vinylsiding

 

 

 

36” ..........................

vinyl siding

 

 

 

P

=

8 ft.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QMIN

 

RMAX

 

Twilight-II-B

 

10 feet

 

2 x Q ACTUAL

 

1 additional termination cap

 

Q + 3 feet

 

1 x Q ACTUAL

 

2 additional termination caps

 

Q + 6 feet

 

2/3 x Q ACTUAL

 

3 additional termination caps

 

Q + 9 feet

 

1/2 x Q ACTUAL

 

 

 

RMAX = (2 / # caps plus appliance) x QACTUAL

 

This appliance is approved for installation onto screened porches with the following guidelines:

Minimum porch area: 96 square feet Minimum ceiling height: 92 inches Minimum two walls must be screened

Minimum top of screen height, side walls: 6 ft. 8 in. Minimum screen area: 64 square feet

NOTE: There may be some odor and small amounts of soot associated with venting theTwilight-II-Bonto a screened porch. Ensuring good cross draft ventilation and routine maintenance of the appliance will maximize comfort and cleanliness.

10

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

5 Appliance Preparation

A.Removing Non-combustibleFacing Material Assembly

The non-combustibleassembly is located onright-handside of appliance (when looking from outdoor side of appliance).

CAUTION

Handle with care.

Non-combustiblematerial may be damaged if dropped.

Hold non-combustiblepieces in place.

Remove and save two screws from upper bracket.

Remove non-combustiblepieces.

Remove and save three screws from lower bracket.

Discard brackets.

Replace screws in holes where brackets were attached to appliance.

 

APPLIANCE

 

EXTERIOR

 

METAL HEARTH STRIP

 

UNDER EDGE OF

 

APPLIANCE

Figure 5.1

Positioning the Metal Hearth Strip

CAUTION

Handle with care.

Avoid damaging protruding edges on outdoor side of appliance.

B. Securing and Leveling the Appliance

WARNING

Fire Risk.

Prevent contact with sagging, loose insulation.

Do NOT install against vapor barriers or

exposed insulation.

Placing Metal Hearth Strip

The metal hearth strip (approx. 46 inches x 4 inches) is used to provide added protection where appliance and outer structure meet.

Place a generous bead of silicone caulk into the corner of the protective hearth strip.

Place the metal strip onto the structure where the outer edge of the appliance will sit (see Figure 5.1). It should overlap building paper to prevent water infiltration.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

11

Placing and Securing Appliance

Place the appliance into position. Make sure flashing edges on the outdoor surround fit up tight to the framing.

The diagram shows how to properly position, level, and secure the appliance (see Figure 5.13). Nailing tabs are provided to secure the appliance to the framing members.

Caulk behind flanges before securing to framing.

Place the appliance into position.

Level the appliance from side to side and front to

 

back.

Í

Shim the appliance as necessary. It is acceptable to

 

use wood shims.

Keep nailing tabs flush with the framing.

Secure the appliance to the framing by using nails or

 

screws through the nailing tabs.

SECURE TO

FRAMING

SECURE TO FRAMING

APPLIANCE

IN A MINIMUM 3

EXTERIOR

PLACES PER SIDE

 

NOTE: Caulk behind all flanges before securing to the exterior.

Figure 5.13 Proper Positioning, Leveling and

Securing of a Appliance

CAUTION

Do NOT notch into the framing around the appliance spacers.

Placing Flashing and Sheathing

Apply high temperature silicone sealant to corner edges Í of fireplace flange (see Figure 5.14).

APPLY HIGH

TEMPERATURE

SILICONE SEALANT

TO CORNER EDGES

FIREPLACE

FLANGE

BEND IN

FLANGE

Figure 5.14

Install outdoor flashing header (sheetmetal piece removed from shipping pallet). Place over upper portion of shroud flange. Line up holes on shroud sides (see Figure 5.15)

FLASHING

HEADER

(SLIDE DOWN)

FLASHING HEADER

(INSTALLED)

Figure 5.15

12

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

Seal flashing to exterior of building using hightemp caulk. Attach to building using holes provided on the top of the left and right sides of outdoor flashing (see Figure 5.15).

Í Apply housewrap or building paper

For placement of combustible housewrap or building paper and non-combustiblesheathing for the outside wall see Figures 5.16 and 5.17.

Special care should be taken when choosing building materials for weather proofing (i.e. building wraps, sealant tapes, liquid sealants, rubberized flashings, etc.). All sealant materials or building wraps installed within 6 inches of the top and sides of the fireplace surround must be approved to a minimum temperature of 225° F continuous exposure. Consult the material’s manufacturer to ensure product compliance.

TOP OF SURROUND

METAL FLASHING

 

 

6 IN.

EDGE OF SURROUND

6 IN.

 

Í Figure 5.16 Outside View withoutNon-combustibleSheathing Shown

 

SHEATHING,

 

COMBUSTIBLE

WALL STUD

HOUSEWRAP **

 

(BUILDING

 

PAPER) OVERLAP

 

FLASHING 1 in.

FIREPLACE

 

HEADER

 

HOUSEWRAP

NON-COMBUSTIBLE*

 

SHEATHING

INSULATION

12 in.

16-5/16in.

 

FLASHING

TOP OF

FIREPLACE

HEADER

 

INSULATED

TL-TRIMKIT

FRAMING

 

STANDOFF

 

 

TOP HOOD

 

APPLIANCE

 

HOOD

Figure 5.17

 

*NOTE: All finishing materials on top of exterior sheathing must benon-combustiblefor a minimum of 12 inches above and on both sides of the exterior face of the appliance. Thisnon-combustiblefinishing material can be up to a maximum of 6 inches thick (6 inches maximum horizontal overhang) to allow for brick and stone alcoves (see Figure 8.5).

** NOTE: Combustible house wrap or building paper

Í

MUST NOT extend over the outside ofnon-combustible

 

sheathing, and MAY extend over theflashing behind non-

 

combustible sheathing. Use high temp silicone or sealant

 

recommended by the manufacturer of the housewrap to

 

seal between combustible sheathing house wrap and non-

 

combustible sheathing. The sealant material used within

 

6 inches of the top and sides of the fireplace surround

 

must be approved to a minimum temperature of 225° F

 

continuous exposure.

 

Once the appliance is in place use enough high temperature silicone sealant or manufacturer specified sealant (approved to a minimum of 225° F) to make a water tight seal between outdoor surround and exterior sheathing.

Face the perimeter of the appliance with non-combustiblesheathing over shroud flanges and flashing. See Figure 5.18 fornon-combustiblezone.

NON-COMBUSTIBLE

 

ZONE

 

12 in.

12 in.

 

12 in.

Figure 5.18 Non-combustibleZone (Exterior)

 

WARNING

Risk of Fire

Non-combustibleclearances must be maintained.

• Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in thenon-combustiblezone.

See Sections 3 and 8 for proper clearances.

See Section 1 forcombustible /non-combustibledefinitions.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

13

C.Installing Non-combustibleFacing Material (Outdoor Side)

WARNING

Fire Risk.

Follow these instructions exactly.

Facing materials must be installed properly to prevent fire.

No materials may be substituted

without authorization by Hearth & Home Technologies.

Center and attach two top boards (the two shorter pieces) to the framing members. See Figure 5.19.

Use fasteners from fastener packet (in manual bag) in shaded areas (see Figure 5.19).

Use regular sheetrock screws in non-shadedareas.

Apply fasteners from

fastener packet in

these areas.

Figure 5.19 Attaching Non-combustibleFacing Material

(Outdoor Side Only)

Attach the left and right side pieces to the framing members. (See Figure 5.20).

NON-COMBUSTIBLE

FACING MATERIAL

49-5/8in.

66-1/8in.

Figure 5.20 Complete Installation of Non-combustible

Facing Material (Outdoor Side)

Use a wet or dry towel or soft brush to remove dust or dirt from facing material.

Apply a non-combustibleadhesive to attach tile, stone or othernon-combustiblefinishing materials per manufacturer’s instructions.

14

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

6 Gas Information

A. Fuel Conversions

C. Gas Connection

Before making gas connections ensure that appliance being installed is compatible with the available gas type.

Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and listed gas conversion kit.

NOTE: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.)

B. Gas Pressures

Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA51.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressures must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum

5.0 inches

11.0 inches

Inlet Pressure

w.c.

w.c.

Maximum Inlet

14.0 inches

14.0 inches

Gas Pressure

w.c.

w.c.

Manifold

3.5 inches

10.0 inches

Pressure

w.c.

w.c.

NOTE: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Refer to Reference Section 13 for location of gas line access in appliance.

NOTE: Gas line may be run from either side or the bottom of the appliance provided the hole in the outer wrap does NOT exceed2-1/2inches in diameter and does not penetrate the firebox.

WARNING

Gas Leak Risk

Support control when attaching pipe to prevent bending gas line.

NOTE: The gap between the supply piping and gas access hole may be caulked with high temperature caulk or stuffed with non-combustible unfaced insulation to prevent cold air infiltration.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

15

Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes.

Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.

WARNING

Fire or Explosion Hazard

• Gas build-upduring line purge may ignite.

• Purge should be performed by qualified technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING

CHECK FOR GAS LEAKS

Explosion Risk

Fire Risk

Asphyxiation Risk

Check all fittings and connections.

Do not use open flame.

After the gas line installation is complete, all connections must be tightened and checked

for leaks with a commercially-available,non-corrosiveleak check solution. Be sure to rinse off all leak check solution following testing.

Fittings and connections may have loosened during shipping and handling.

WARNING

Fire hazard.

Do NOT change the valve settings.

This valve has been preset at the factory.

Changing valve settings may result in fire hazard or bodily injury.

HIGH ALTITUDE INSTALLATIONS

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

16

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

7 Electrical Information

A. Recommendation for Wire

This appliance requires 110-120VAC be wired to the junction box for proper operation of the appliance.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

CAUTION

Shock hazard.

Replace damaged wire with type 105O C rated wire.

Wire must have high temperature insulation.

NOTE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

NOTE: Waterproof insulated wire should be used when wiring the junction box.

B. Connecting to the Appliance

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

If using thermostat use one compatible with a millivolt gas valve system.

Follow parameters for locating thermostat (see individual thermostat instructions) to ensure proper operation of appliance.

Keep wire lengths short as possible by removing any excess wire length.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

17

C. Optional Accessories

Optional fan and remote control kits require that 110-120VAC be wired to the factory installed junction box before the appliance is permanently installed (see Figure 7.1).

Fan Installation

To provide best airflow, we recommend positioning fan on the left side (as viewed from appliance interior side - see Figure 7.2). NOTE: It is recommended fan be installed prior to gas line installation.

Wall Switch

Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the appliance ON/ OFF switch pigtails.

APPLIANCE

 

INTERIOR

 

SIDE

 

FAN

 

DRIP

 

TRAY

Figure 7.2

Fan location

FAN SPEED

 

 

CONTROL

 

WIRE LEAD

(RHEOSTAT)

6 FT.

 

1 MALE END

 

APPROX.

1 FEMALE END

TEMPERATURE

SENSOR SWITCH

WIRE LEAD

2 FEMALE ENDS

6 FT.

APPROX.

FAN KIT

#GFK-160T

PLUG AND WIRE

ASSEMBLY

DETAIL A

JUNCTION BOX

SEE DETAIL A

NOTE: If any of the original wire as supplied with the appliance must be replaced, it must be replaced with the type 105oC rated wire.

Figure 7.1 Fan Wiring Diagram

18

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

D. Intellifire Ignition System Wiring

This appliance requires a 110 VAC supply to the appliance junction box for operation. When using the transformer, the junction box must have uninterrupted 120V. A wiring diagram is shown in Figure 7.3.

This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

This appliance is supplied with a battery pack and a 3 voltAC transformer, which requires the installation of the supplied junction box. It is highly recommended that the junction box be installed at this time to avoid reconstruction.

The battery pack requires two D cell batteries (not included).

NOTE: Batteries cannot be placed in the battery pack while using the 3 volt AC transformer. The transformer must be unplugged if the battery pack is used or battery life will be reduced.

CAUTION

Battery polarity must be correct or module damage will occur.

Optional Accessories Requirements

Wiring for optional accessories should be done now to avoid reconstruction.

PLUG-IN

IGNITION MODULE

3 VAC

3V TRANSFORMER

 

ON/OFF

 

WALL

 

SWITCH

 

 

FLAME SPARKER/

 

SENSOR

IGNITION

 

MODULE

 

(3V)

 

VALVE

LOW VOLTAGE

 

SEE NOTE 1

 

GROUND REMOTE

NEUTRAL

CONTROL HOT

 

WHITE WIRE

 

CAN BE

 

PLUGGED

 

INTO ANY

BLACK WIRE CAN BE

OF #1-#5

PLUGGED INTO ANY OF

LOCATIONS

#1 - #5 LOCATIONS

ON THE

ON THE HOT SIDE

NEUTRAL SIDE TRANSFORMER

 

3 VAC

 

PLUG IN

I

S

WHT

ORG

GROUND TO

FIREPLACE

CHASSIS

BRN

BRN

*

 

ORG

PIGGYBACK

ON/OFF SWITCH

VALVE

INTERMITTENT

PILOT

IGNITOR

GRN

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts.

Uninterrupted 120 VAC is required at junction box unless equipped with battery back-up.

Figure 7.3 Intellifire Pilot Ignition (IPI) Wiring Diagram

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

19

E. Junction Box Installation

If the box is being wired from the OUTSIDE of the appliance:

Install the Romexconnector (not included with appliance) in the side wrap.

Loosen two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

Make all necessary wire connections.

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 7.4).

Pull the electrical wires from outside the appliance through this opening into the valve compartment.

 

HEAT SHIELD

 

 

 

14/2WG

 

 

COPPER GROUND

WHT

BLK

ATTACHED TO GRN SCREW

 

 

WITH GRN WIRE

 

BLK

GREEN WIRE

WHT

 

 

INSIDE BOX

 

 

NOTE: Do NOT wire

Figure 7.4 Junction Box Detail

110 VAC to wall switch.

 

Loosen the two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.

F.Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall

 

 

 

 

 

 

 

mounted switch for use with a fan

 

 

 

 

 

 

 

(See Figure 7.5):

 

 

 

 

 

 

 

• The power supply for the appliance

 

 

 

6 INCH

 

 

 

 

 

 

APPROX.

 

 

 

must be brought into a switch box.

FAN

 

 

 

 

WIRE LEAD

 

• The power can then be supplied

 

 

 

 

 

SPEED CONTROL

 

 

 

 

 

 

 

 

 

1 MALE END

 

 

from the switch box to the appli-

(RHEOSTAT)

 

 

 

 

1 FEMALE END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ance using a minimum of 14-3with

 

 

 

 

 

TEMPERATURE

 

 

ground wire.

 

 

 

 

 

 

 

 

 

 

 

 

SENSOR SWITCH

 

At the switch box connect the black

 

 

 

 

 

WIRE LEAD

 

 

(hot) wire and red (switch leg) wire

 

 

 

 

 

2 FEMALE ENDS

JUNCTION

 

 

 

 

 

 

 

BOX

 

to the wall switch as shown.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

At the appliance connect the black

 

 

 

 

 

6 INCH

 

 

 

 

 

 

APPROX.

 

 

(hot), white (neutral) and green

 

 

FAN

 

 

 

 

 

(ground) wires to the junction box

 

 

 

 

 

 

 

 

as shown.

 

 

 

 

 

 

 

• Add a 1/4 inch insulated female

 

 

 

 

 

 

 

 

connector to the red (switch leg)

 

 

 

 

 

 

 

 

wire, route it through the knockout

 

 

PLUG AND WIRE

 

 

 

 

 

in the face of the junction box, and

 

 

ASSEMBLY

 

 

 

 

 

 

 

 

 

 

 

 

 

connect to the top fan switch con-

 

 

 

 

 

 

 

 

nector (1/4 inch male) as shown.

 

 

 

 

 

OPTIONAL

 

 

 

Figure 7.5 Junction Box Wired to Wall Switch

 

WALL SWITCH

 

 

 

 

 

 

20

Heat & Glo LifeStyle Collection

Twilight-II-B2108-900

Rev. G

8/07

 

8 Finishing

A. Mantel Projections

Figure 8.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance.

Interior

 

CEILING

View

 

 

 

NON-COMBUSTIBLEBOARD

 

(SUPPLIED ON APPLIANCE)

 

 

INDOOR SIDE ONLY

 

 

 

12

 

10

11

 

35-3/4

 

9

 

 

 

8

 

 

7

13-5/8

 

6

12-5/8

 

11-5/8

 

10-5/8

 

 

9-5/8

 

 

8-5/8

 

HOOD

7-5/8

 

 

Note: Measurements

 

are in inches.

Figure 8.1 Indoor Clearances to Mantels or other

Combustibles above Appliance

 

Top View

MEASURED

FROM CORNER

½ IN.

FIREPLACE

HOOD

Figure 8.2 Clearances to Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening.)

B. Facing Material

WARNING

Fire Risk.

Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles.

• Modifying or covering grilles could cause temperature rise and fire hazard.

Finishing materials must not interfere with:

Air flow through grilles or louvers.

Operation of louvers or doors.

Access for service.

Inside Facing Material

May install combustible materials up to specified clearances on top, front and sides of appliance.

Seal joints between finished wall and appliance top and sides with 300º F (140º C) minimum sealant.

Leave space so bottom grille can be lowered for trim door removal.

NON-COMBUSTIBLEZONE

 

 

 

 

 

 

 

 

 

 

 

 

 

41-7/8in.

 

 

 

 

 

 

 

 

 

2-3/4in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 8.3 Non-combustibleZone (Interior)

Outside Facing Material

OVERHANG

A

SIDING

A

B

 

 

 

A

SIDING

 

 

SIDING

 

Vinyl

Non-vinyl

A

36 in.

12 in.

B

64-5/16in.

35-5/16in.

Figure 8.4 Exterior View - Minimum Clearances

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

21

WARNING

Risk of Fire

Non-combustibleclearances must be maintained.

Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in the noncombustible zone.

See Sections 3 & 8 for proper clearances.

See Section 1 for combustible/noncombustible definitions.

May install non-combustiblematerials to cover gap between facing material and appliance (see Figure 8.5).

WARNING

Fire Risk.

Finish all edges and fronts to clearances and specifications listed in manual.

Black metal columns may be covered with non-combustiblematerial only.

Do NOT overlap combustible materials onto appliance front.

Install combustible materials only up to specified clearances on top, front and side edges.

Seal joints between the finished wall and appliance top and sides using only a 300º F minimum sealant.

WARNING

Fire Risk.

Water Intrusion Risk.

Hood is required.

Flashing and non-combustiblesheathing must be installed before facing materials.

Facing must be non-combustibleand seal tight to fireplace front.

COMBUSTIBLE

 

HOUSEWRAP

SHEATHING

 

 

 

 

NON-COMBUSTIBLE

 

 

SHEATHING

 

 

(SUPPLIED)

 

 

BRICK LEDGE

 

12 in.

 

 

 

NON-COMBUSTIBLE

 

 

FACING

REQUIRED

 

 

FLASHING

 

 

(SUPPLIED)

 

 

 

 

THERE MUST BE NO GAP

 

6 in.

BETWEEN BRICK LEDGE,

 

FACING MATERIAL AND

 

MAX.

 

APPLIANCE FRONT.

 

 

 

 

6 in. MAXMUM PROJECTION

 

 

FROM FACE OF FIREPLACE

HOOD

HOUSE

WRAP NON-COMBUSTIBLESHEATING

12 in.

Figure 8.5 Exterior View

22

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

NOTE: All finishing materials on top of exterior sheathing must benon-combustiblefor a minimum of 12 inches above and on both sides of the exterior face of the appliance. Thisnon-combustiblefinishing material can be up to a maximum of 6 inches thick (6 inches maximum horizontal overhang) to allow for brick and stone alcoves (see Figure 8.5).

NOTE: Combustible housewrap or building paperMUST NOT extend over the outside ofnon-combustiblesheathing, andMAY extend over theflashing header behindnon-combustiblesheathing. Use hightemp caulk to seal between combustible sheathing housewrap and noncombustible sheathing.

STUD WALL

FIREPLACE

HEADER

HOUSEWRAP

INSULATION

FLASHING

HEADER

INSULATED

FRAMING

STANDOFF

CEILING OR OVERHANG

SOFFIT

 

 

SHEATHING,

 

 

COMBUSTIBLE

 

 

HOUSEWRAP

 

 

(BUILDING

 

 

PAPER) OVERLAP

35-5/16in.

FLASHING 1 in.

MINIMUM CLEARANCE TO

 

NON-VINYLSOFFIT, MANTEL,

NON-COMBUSTIBLE

CEILING OR OVERHANG.

 

 

SHEATHING

64-5/16in.

 

 

MINIMUM CLEARANCE

 

TO VINYL SOFFIT,

 

CEILING OR OVERHANG.

12 in.

TOP OF

FIREPLACE

APPLIANCE

TOP HOOD

HOOD

 

Figure 8.6 Exterior View

HOUSEWRAP (BUILDING

PAPER) AND SHEATHING

DETAIL -

SEE FIGURE 8.5

INSULATION

APPLIANCE

HOOD

 

SOFFIT

 

 

 

 

 

SIDING

 

 

 

 

 

 

DRAIN PLANE

35-5/16in.

MINIMUM CLEARANCE

DETERMINED BY

TO NON-VINYL

LOCAL CODE

64-5/16in.

 

 

CLEARANCE TO VINYL

SOFFIT, OVERHANG, MANTEL,

OR CEILING

12 in. MINIMUM CLEARANCE TO NON-VINYLSIDING

36 in. MINIMUM CLEARANCE TO VINYL SIDING

TOP OF

APPLIANCE

TOP OF HOOD

BRICK OR OTHER NON-COMBUSTIBLE

FACING MATERIAL 6 INCH MAXIMUM

PROJECTION FROM SURFACE OF

FIREPLACE (INCLUDES NON-COMBUSTIBLE

MANTEL PROJECTION)

NON-COMBUSTIBLEBRICK LEDGE

MUST BE TIGHT TO APPLIANCE

FACE OR NON-COMBUSTIBLESHEATHING

Figure 8.7 Exterior View with Non-combustibleFacing Material

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

23

9 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

Placing Lava Rock

Place lava rock on refractory support pan. Cover entire support pan surface (see Figure 9.1).

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 13.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listedaccessories voids warranty.

Using non-listedaccessories may result in a safety hazard.

Only Hearth & Home Technologies approved

accessories may be used safely.

D. Lava Rock and Ember Placement

WARNING

Explosion Risk.

Follow ember placement instructions in manual.

Do NOT place embers directly over burner ports.

Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Figure 9.1 Placement of Lava Rock

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

Embers CANNOT be placed directly over ports.

When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place thedime-sizeember pieces just in front of the port trail, but not on or in between the ports (see Figure 9.2). Failure to follow this procedure will likely cause lighting and sooting problems.

Figure 9.2 Placement of Ember Materials

Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

24

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

E. Positioning the Logs

Log Set Assembly: LOGS-TWI

3

4

1

2

5

6

 

7

 

 

CAUTION: Logs are fragile! Carefully remove the logs from the packaging. Remove the metal supports which held the log box in place during shipping.

STEP 1. Before positioning the logs, refer to the installation manual for electric ember setup and ember placement.

1

1-inch

Indents

STEP 2. LOG #1(SRV2005-701):Use the indents on the bottom side of the log to position the large end of the log onto the grate tine as shown. Position the thin end of log #1 one inch from port pattern as shown.

Grate Bar Cutout

1

2

Pilot

Assembly

Cutout

STEP 3. LOG #2(SRV2005-700):Position log #2 on the left grate bar and the pilot assembly. Use the cut out notches on the log to position it as shown.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

25

32 1

STEP 4. LOG #3(SRV2005-702):Position log #3 as shown by leaning it against log # 2 and resting the other end on the peak of the burner. Do not cover any port holes.

2

4

1

3

 

 

Smooth Cutout

Sharp

Notch

STEP 5. LOG #4(SRV2005-703):Locate the sharp notch on log #4 against the grate tine as shown. The smooth cutout on log #4 should rest on the burner surface. As with log #3, be careful not to cover any port holes.

1

5

Sharp

Notch

STEP 6. LOG #5(SRV2005-704):Using the sharp notch on the heavy end of log #5, align it on the grate tine and on log #4 as shown.

26

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

3

4

1

2

5

6

 

 

STEP 7. LOG #6(SRV2077-701):Set log #6 onto the grate bar as shown. Lay the “Y” end of log #6 onto log #1 resting it into the small depression of log #1.

3

4

1

2

5

6

 

7

 

 

 

 

 

STEP 8. LOG #7(SRV703-703):Place log #7 on the grate tine between log #2 and log #5. Rest one end on the burner making sure not to cover any port holes.

F. Glass Assembly

WARNING

Handle glass doors with care.

Inspect the gasket to ensure it is undamaged.

Inspect the glass for cracks, chips or scratches.

Do NOT strike, slam or scratch glass.

Do NOT clean glass with a razor blade.

Do NOT operate appliance with glass door removed, cracked, broken or scratched.

Replace glass door assembly as a complete appliance.

Removing Glass Assembly

Remove wing nuts and glass clips around glass door. Remove glass door from the appliance.

Replacing Glass Assembly

Replace the glass door on the appliance.

G. Grilles and Trim

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other non-combustiblematerials can be used to cover up the gap between the sheet rock and the appliance.

Do not obstruct or modify the air inlet/outlet grilles. When overlapping on both sides, leave enough space so that the bottom grille can be lowered and the trim door removed.

H. Shutter Settings

 

NG

LP

Twilight-II-B

3/8 in.

Full Open

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

27

10 Operating Instructions

A. Before Lighting Appliance

This appliance has an Intellifire ignition system.

CAUTION

If installing Intellifire ignition battery backup:

Do not install batteries if the backup mode may not be used for extended time.

Batteries may leak.

Install batteries only when needed for power outage.

Before operating this appliance have a qualified technician:

Remove all shipping materials from inside and/or underneath the firebox.

Review proper placement of logs, rockwool, lava rock, and vermiculite.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position.

Ensure that the flow of combustion and ventilation air is not obstructed (front grilles and vent caps).

WARNING

Glass door must be in place when appliance is operating.

Risk of:

Combustion Fumes

Fire

Do NOT operate appliance with glass door removed.

Open viewing glass for servicing only.

Glass door MUST be in place and sealed before operating appliance.

Only use glass door certified for use with appliance.

Glass replacement should be done by qualified technician.

WARNING

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

Keep children away.

CAREFULLY SUPERVISE children in same room as appliance.

Alert children and adults to hazards of high temperatures.

Do NOT operate with protective barrier open or removed.

Keep clothing, furniture, draperies and other combustibles away.

A protective barrier is provided on the interior door to prevent direct contact with the fixed glass panel. Do NOT operate the appliance without that protective barrier.

Contact your dealer or Hearth & Home Technologies if help is needed to properly install a protective barrier.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

28

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

B. Lighting Appliance

Intellifire Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. Do not try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. Do not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

LIGHTING

INSTRUCTIONS (IPI)

1.Turn off all electric power to the appliance.

2.This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand.

GAS

VALVE

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you don’t smell gas, go to next step.

4.Turn on all electric power to the appliance.

5.To light the burner, flip the ON/OFF switch to the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6.If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Turn off all electric power to the appliance if service is to be performed.

2.Flip ON/OFF switch to the “OFF” position.

593-913D

Final Inspection by ________________________________

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

29

C. After Appliance is Lit

Initial Break-inProcedure

When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

NOTE: The appliance should be run three to four hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours. This will help to cure the products used in the paint and logs.

During this break-inperiod it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

CAUTION

Smoke and odors released during initial operation.

Open windows for air circulation.

Leave room during initial operation.

Smoke may set off smoke detectors.

Smoke and odors may be irritating to sensitive individuals.

WARNING

Fire Risk.

High Temperatures.

Keep combustible household items away from appliance.

Do NOT obstruct combustion and ventilation air.

Do NOT place combustible items on top of or in front of appliance.

Keep furniture, draperies away from appliance.

WARNING

Fire Hazard.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

Do NOT store flammable materials in the appliance’s vicinity.

Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids in this appliance.

Combustible materials may ignite.

D. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation of the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

condensation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appliance is al-

lowed to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this appliance may release an odor for the first several hours. This is

Odor from appliance

caused by the curing of the paint and the burning off of any oils remaining from manufactur-

ing. Odor may also be released from finishing materials and adhesives used around the

 

 

appliance.

 

 

Film on the glass

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See

 

your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the appliance.

 

 

Is it normal to see the pilot flame burn

In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when

continually?

ON/OFF is turned off. In a standing pilot system the pilot will always stay on.

 

 

30

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

11 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

A. Intellifire Ignition System

Sympton

Possible Cause

Corrective Action

1. The ignitor/module

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to

makes noise, but no

 

correct terminals on module and pilot assembly. Reversed wires at the module may

spark.

 

cause system to make sparking noise, but spark may not be present at pilot hood.

 

 

 

 

b. Loose connections

Verify no loose connections or electrical shorts in wiring from module to pilot assem-

 

or electrical shorts in

bly. Rod closest to pilot hood should be ignitor. Verify connections underneath pilot

 

the wiring.

assembly are tight; also verify connections are not grounding out to metal chassis,

 

 

pilot burner, pilot enclosure, mesh screen if present, or any other metal object.

 

c. Ignitor gap is too

Verify gap of igniter to pilot hood. The gap should be approximately .17 inch or 1/8

 

large.

inch.

 

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire

 

 

“I” from module. Place ON/OFF Rocker switch or wall switch in ON position. Hold

 

 

ground wire about 3/16 inch away from “I” terminal on module. If there is no spark

 

 

at “I” terminal module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked insulator around

 

 

electrode.

2. Pilot won’t light,

a. Transformer

Verify that transformer is installed and plugged into module. Check voltage of trans-

there is no noise or

installed correctly.

former under load at spade connection on module with ON/OFF switch in ON posi-

spark.

 

tion. Acceptable readings of a good transformer are between 3.2 and 2.8 volts AC.

 

b. A shorted or loose

Remove and reinstall the wiring harness that plugs into module. Verify there is a

 

connection in wiring

tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each

 

configuration or wiring

wire in wiring harness.

 

harness.

 

 

c. Improper wall switch

Verify that 110/VAC power is “ON” to junction box.

 

wiring.

 

 

d. Module not

Verify black ground wire from module wire harness is grounded to metal chassis of

 

grounded.

appliance.

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire

 

 

“I” from module. Place ON/OFF Rocker switch or wall switch in ON position. Hold

 

 

ground wire about 3/16 inch away from “I” terminal on module. If there is no spark

 

 

at “I” terminal module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked insulator around

 

 

electrode.

3. Pilot lights but

a. A shorted or loose

Verify all connections to wiring diagram in manual. Verify connections underneath

continues to spark,

connection in sensor

pilot assembly are tight. Verify connections are not grounding out to metal chassis,

and main burner will

rod.

pilot burner, pilot enclosure or screen if present, or any other metal object.

not ignite. (If the pilot

b. Poor flame rectifi-

Verify that flame is engulfing sensor rod. If the pilot assembly does not have a

continues to spark

cation or contaminated

ground strap, consider installing one to increase flame rectification. Verify correct pi-

after the pilot flame

sensor rod.

lot orifice is installed and inlet gas specifications. Flame carries rectification current,

has been lit, flame

 

not the gas. If flame lifts from pilot hood, the circuit is broken. A wrong orifice or too

rectification has not

 

 

high an inlet pressure can cause pilot flame to lift. The sensor rod may be contami-

occurred.)

 

 

nated. Clean sensor rod with emery cloth.

 

 

 

c. Module is not

Verify that module is securely grounded to metal chassis of appliance. Verify that

 

grounded.

wire harness is firmly connected to module.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

31

Intellifire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

3. Continued

d. Damaged pilot as-

Verify that ceramic insulator around the sensor rod is not cracked, damaged, or

 

sembly or dirty sensor

loose. Verify connection from sensor rod to white sensor wire. Clean sensor rod with

 

rod.

emery cloth to remove any contaminants that may have accumulated on sensor rod.

 

 

Verify continuity with a multimeter with ohms set at lowest range.

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire

 

 

“I” from module. Place ON/OFF Rocker switch or wall switch in ON position. Hold

 

 

ground wire about 3/16 inch away from “I” terminal on module. If there is no spark

 

 

at “I” terminal module must be replaced. If there is a spark at “I” terminal, module

 

 

is fine. Inspect pilot assembly for shorted sparker wire or cracked insulator around

 

 

electrode.

4. Pilot sparks, but

a. Correct gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet pressure reading is

Pilot will not light.

 

within acceptable limits, inlet pressure must not exceed 14 in. W.C.

 

b. Ignitor gap is too

Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in.

 

large.

 

 

c. Module is not

Verify module is securely grounded to metal chassis of appliance.

 

grounded.

 

32

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

12 Maintaining and Servicing Appliance

A. Maintenance Tasks

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-upat the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

Turn off gas.

Turn off electricity to appliance.

Disable remote control, if one is present.

Ensure appliance is completely cooled.

After servicing:

Replace any screen or barrier that was removed.

Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

Condition of doors, surrounds and fronts.

Condition of glass, glass assembly and glass seal.

Obstructions of combustion and ventilation air.

Condition of logs.

Condition of firebox.

Burner ignition and operation.

Burner air shutter adjustment

Gas connections and fittings.

Obstructions of termination cap.

Clean:

• Glass

Air passageways, grilles, control compartment

Burner, burner ports

Risk of:

Fire

Delayed ignition or explosion

Exposure to combustion fumes

Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial3-4hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when hot.

Turn off appliance after 3-4hours of operation and ALLOW TO COOL.

Remove and clean glass assembly.

Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

33

Inspect

 

Maintenance Tasks

Doors, Surrounds

1. Assess condition of screen and replace as necessary.

and Fronts

Recommend addition of screen if one is not present.

 

2.

Inspect for scratches, dents or other damage and repair as necessary.

 

 

 

 

3.

Verify no obstructions to airflow through the louvers.

 

 

 

 

4.

Verify maintenance of proper clearance to combustible household objects.

Gasket Seal, Glass

1. Inspect gasket seal and its condition.

Assembly and Glass

 

 

2.

Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.

 

 

 

 

 

3.

Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

4.

Verify that latches engage properly, clip studs are not stripped, and glass attachment components are intact

 

and operating properly. Replace as necessary.

 

5.

Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.

Valve Compartment

1.

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw

and Firebox Top

tips that have penetrated the sheet metal are sharp and should be avoided.

 

2.

Remove any foreign objects.

 

3.

Verify unobstructed air circulation.

Logs

1.

Inspect for broken, damaged, or missing logs. Replace as necessary.

 

 

 

 

2.

Verify correct log placement and no flame impingement causing sooting. Correct as necessary.

Firebox

1.

Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.

 

2.

Replace appliance if firebox has been perforated.

 

 

 

Burner Ignition and

1.

Verify burner is properly secured and aligned with pilot or igniter.

Operation

 

 

2.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

 

 

3.

Replace ember materials with new dime-sizeand shape pieces. Do not block ports or obstruct lighting paths.

 

4.

Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.

 

 

 

 

5.

Inspect for lifting or other flame problems.

 

 

 

 

6.

Verify air shutter is clear of dust and debris.

 

 

 

 

7.

Inspect orifice for soot, dirt or corrosion.

 

8.

Verify manifold and inlet pressures. Adjust regulator as required.

 

 

 

 

9.

Inspect pilot flame strength. Clean or replace orifice as necessary.

 

 

 

10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery

 

cloth or replace as required.

 

11. Verify millivolt output. Replace as necessary.

 

 

Venting

1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

3.

Verify that termination cap clearance to subsequent construction (building additions, decks, fences or

 

sheds) has been maintained.

 

4.

Inspect for corrosion or separation.

 

 

 

 

5.

Verify weather stripping, sealing and flashing remains intact.

 

 

 

 

6.

Inspect draft shield to verify it is not bent, damaged or missing.

 

 

Remote controls

1. Verify operation of remote.

 

2.

Replace batteries in remote transmitters and battery-poweredreceivers.

 

3.

Verify batteries have been removed from battery back-upIPI systems to prevent premature battery failure

 

or leaking.

34

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

13 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

 

 

OUTDOOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

E

G

 

 

 

OUTDOOR

 

 

 

 

 

 

 

 

OUTDOOR

 

 

 

 

 

 

 

 

 

A

 

C

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

I

 

 

ELECTRICAL

 

 

 

 

 

 

 

 

 

GAS LINE

 

 

 

 

 

 

 

 

 

ACCESS

ACCESS

 

 

 

 

 

 

J

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

 

K

 

N

 

O

 

 

 

 

 

Q

 

 

 

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

 

 

M

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

INDOOR VIEW

 

 

 

 

 

OUTDOOR VIEW

 

Location

Inches

Millimeter

 

Location

 

Inches

Millimeter

 

A

2-1/4

57

 

J

 

4-1/2

114

 

 

 

B

4-3/4

121

 

K

 

32-5/8

829

 

 

 

C

1/2

13

 

L

 

36-1/4

919

 

 

 

D

43

1091

 

M

 

41-7/8

1062

 

 

 

E

24

609

 

N

 

21-1/2

547

 

 

 

F

46-3/4

1187

 

O

 

38-5/8

981

 

 

 

G

40-3/4

1035

 

P

 

42-1/8

1070

 

 

 

H

3-3/8

86

 

Q

 

21-1/2

546

 

 

 

I

2-1/2

64

 

R

 

35-5/8

905

 

 

 

Figure 13.1 Appliance Dimensions

 

 

 

 

 

 

 

 

 

 

Heat & Glo LifeStyle Collection

Twilight-II-B

2108-900

Rev. G

8/07

35

B. Service Parts

Twilight-II-B

 

 

Service Parts Diagram

Beginning Manufacturing Date: 1-06

Ending Manufacturing Date: ______

 

17

Flashing Header

11

(Component of

 

Trim Kit)

 

10

8

14 13

9 16

12

15

Log Set Assembly

 

 

3

4

1

 

 

 

 

 

2

 

5

6

 

7

 

 

 

Part number list on following page.

36

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

Service Parts List

 

Twilight-II-B

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located

 

 

 

AVAILABLE

on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure

 

 

TO SHIP IN

correct service parts.

 

 

 

 

24 HOURS

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

 

Log Set Assembly

 

LOGS-TWI

Y

1

Log 1

 

SRV2005-701

 

2

Log 2

 

SRV2005-700

 

3

Log 3

 

SRV2005-702

 

4

Log 4

 

SRV2005-703

 

5

Log 5

 

SRV2005-704

 

6

Log 6

 

SRV2077-701

 

7

Log 7

 

SRV703-703

 

8

Burner Assembly

 

2087-004

Y

9

Grate Assembly

 

2005-012

 

10

Refractory, Side

 

SRV2005-730

 

11

Outdoor Glass Assembly

 

GLA-OUTDOOR2

Y

12

Junction Box Shield

 

2087-149

 

13

Indoor Glass Assembly

 

GLA-6TROC

Y

14

Hood - Interior Side

 

SRV60-143-BK

 

15

Glass Clip

 

2087-121

 

16

Junction Box

 

4021-013

Y

17

Trim Kit, Black

 

TL-TRIM-BK

 

 

Glass Latch Assembly

 

386-122A

Y

 

Non-CombustibleBoards (set only)

 

2108-030

 

 

Lava Rock Bag

 

2005-790

 

 

Mineral Wool

 

050-721

 

 

Pilot Tube

 

446-301

Y

 

Touch Up Paint

 

TUP-GBK-12

 

Conversion Kit NG

NGK-TWI

Y

Conversion Kit LP

LPK-TWI

Y

Pilot Orifice NG

593-528

Y

Pilot Orifice LP

593-527

Y

Regulator NG

NGK-DXF

Y

Regulator LP

LPK-DXF

Y

Additional service part numbers appear on following page.

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

37

Service Parts

Twilight-II-B

Valve Assembly Parts List

Beginning Manufacturing Date: 1-06

 

Ending Manufacturing Date: ______

 

3

IPI VALVE ASSEMBLY

1

5

 

7

 

14

 

 

 

 

12

15

 

 

 

 

 

 

 

6

 

 

 

 

13

8

 

 

 

 

 

 

 

9

 

 

 

 

10

11

 

 

 

2

4

 

 

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located

 

AVAILABLE

on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure

 

 

TO SHIP IN

correct service parts.

 

 

 

 

24 HOURS

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

1

Burner Neck Gasket

 

438-407

 

2

Valve NG

 

593-500

Y

2

Valve LP

 

593-501

Y

3

Flexible Gas Connector

 

383-302A

Y

4

Wire Assembly

 

593-590A

Y

5

Pilot Assembly NG

 

2090-012

Y

5

Pilot Assembly LP

 

2090-013

Y

6

Valve L Bracket

 

674-168

 

7

Burner Orifice (NG) (#32C)

 

582-832

Y

7

Burner Orifice (LP) (#50C)

 

582-850

Y

8

Valve Bracket

 

2087-117

 

9

Flex Ball Valve Assembly

 

302-320A

Y

10

ON/OFF Rocker Switch

 

060-521A

Y

11

Control Module

 

593-592

Y

12

Orifice Bracket

 

2087-109

 

13

Valve Bracket

 

2087-116

 

14

Orifice Bracket Gasket

 

2087-110

 

15

Valve Plate Gasket

 

2087-112

 

 

Battery Pack

 

593-594A

Y

 

3V Adaptor

 

593-593A

Y

38

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

 

C. Limited Lifetime Warranty

LIMITED LIFETIME WARRANTY

HEAT & GLO GAS APPLIANCE PRODUCTS

BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEAT & GLO will replace or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.

EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in material or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and limitations described below.

CONDITIONS, EXCLUSIONS AND LIMITATIONS:

1.This warranty applies to the original owner only and is nontransferable.

2.This warranty applies only to Products installed in the United States of America or Canada.

3.This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an expedient and cost-effectivemanner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT.

4.Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-YearWarranty.

5.Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty unless expressly authorized and approved by HEAT & GLO in writing.

6.Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.

7.This warranty will be void if:

a)The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.

b)Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved by HEAT & GLO in writing.

c)Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.

d)The Product is damaged due to shipping, improper handling, accident, abuse or misuse.

e)Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.

f ) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HEAT & GLO dealer or supplier.

NOTES TO CUSTOMER:

1. In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual servicing by an authorized HEAT & GLO dealer.

2. Please complete this information and retain this warranty in a safe place for future reference: Installation Date:__ Model #:_________________ Serial #:______________ Installing Contractor:______________________

3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products.

© 2005 Hearth & Home Technologies Inc.

060-981D3/05

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07

39

D. Contact Information

Heat & Glo LifeStyle Collection, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.Heatnglolifestyle.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.Heatnglolifestyle.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Printed in U.S.A. - Copyright 2007

40

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900Rev. G • 8/07