Heat & Glo LifeStyle Exclaim-50 User Manual

Size:
7.34 Mb
Download

Owner’s Manual

Installation and Operation

Models:

EXCLAIM-50

Wood Burning Fireplace

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating •

Read, understand

• Leave this manual with

and maintenance

and follow these

party responsible for

instructions included.

instructions for safe

use and operation.

 

installation and

 

 

operation.

 

DO DISCARDNOT

WARNING

WARNING

 

If the information in these instructions is not followed exactly, a

fi re may result causing property damage, personal injury, or death.

Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance.

Do not overfi re. Overfi ring will void your warranty.

Comply with all minimum clearances to combustibles as specifi ed. Failure to comply may cause house fi re.

Installation and service of this fi replace should be performed by qualifi ed personnel. Hearth & Home Technologies suggests NFI certifi ed or factory-trainedprofessionals, or technicians supervised by an

NFI certifi ed professional.

HOT SURFACES!

Screen/mesh, glass doors and other surfaces are hot during operation AND cool down.

Hot screen/mesh and glass doors will cause burns.

DO NOT touch screen/mesh or glass doors until cooled

NEVER allow children to touch screen/mesh or glass doors

Keep children away

CAREFULLY SUPERVISE children in same room as fi replace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable materials.

Keep clothing, furniture, draperies and other fl ammable materials away.

WARNING

Fire Risk

For use with solid wood fuel or decorative gas appliance only.

DO NOT install unvented gas logs.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

1

Read this manual before installing or operating this fireplace. Please retain this owner’s manual for future reference.

Congratulations!

Congratulations on selecting a Heat & Glo wood burning fireplace. The Heat & Glo fireplace you have selected is designed to provide the utmost in safety, reliability and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest you keep it with your other important documents and product manuals.

The information contained in this owner’s manual unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo wood burning fireplace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fireplace products!

Homeowner Reference Information

We recommend that you record the following pertinent

 

 

 

 

 

 

 

information about your fireplace:

 

Model Name:

 

 

Date purchased/installed:

 

 

 

Serial Number:

 

 

Location on fireplace:

 

 

 

Dealership purchased from:

 

 

Dealer phone:

 

 

 

Notes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Listing Label Information/Location

The model information regarding your specific fireplace can be found on the rating plate located on the smoke shield of the fireplace.

Serial

Grate

Fireplace

Number

Model

 

 

FIREPLACE NO.

FIRE DAMAGE. REPLACE MODEL NO.

MODEL NO.

 

MFG. DATE

 

 

WARNING: RISK OF

 

 

 

 

 

 

GRATE WITHHEARTH&HOME

 

 

 

 

 

 

 

 

TECHNOLOGIES INC.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIRECHAMBER INTENDED FOR USE WITH HEARTH & HOME TECHNOLOGIES INC. LISTED FIREPLACE PARTS. SEE INSTALLATION AND OPERATING INSTRUCTIONS FOR THIS MODEL. ONLY HEARTH & HOME TECHNOLOGIES INC. GLASS DOOR KITS CAN BE INSTALLED ON THIS UNIT.

FIREPLACE ALSO FOR USE

YES

 

NO

 

 

 

 

 

CLEARANCE TO

CHIMNEY

FIREBOX

 

 

 

 

 

 

IN.

 

IN MANUFACTURED HOMES

 

 

 

 

 

 

COMBUSTIBLES:

2 IN. MIN.

 

 

 

 

 

 

MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FAN KIT

 

 

 

&

 

 

 

 

 

RATEDAT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MODEL NO.

 

 

 

 

 

 

 

 

115 VOLTS, 50/60 Hz.,

 

 

 

AMP.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DO NOT OVERFIRE. USE ONLY: SOLID WOOD FUEL OR

 

WARNING! THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED

 

 

 

LISTED DECORATIVE GAS APPLIANCE. DO NOT USE A

 

GAS LOG SET. TO REDUCE THE RISK OF FIRE OR INJURY, DO NOT

 

FIREPLACE INSERT OR OTHER PRODUCTS NOT

 

INSTALL AN UNVENTED GAS LOG SET INTO FIREPLACE.

 

SPECIFIED FOR USE WITH THIS PRODUCT. IF DOORS

 

WARNING! THIS APPLIANCE IS NOT FOR USE AS COOKING EQUIPMENT.

 

ARE USED OPERATE FIREPLACE WITH DOORS FULLY

 

 

OPEN OR CLOSED ONLY. WHEN BURNING A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IF INSTALLATION OR OPERATING INSTRUCTIONS ARE MISSING

 

DECORATIVE GAS APPLIANCE IN THE FIREPLACE,

 

 

 

CONTACT: HEARTH & HOME TECHNOLOGIES INC.,

 

 

 

 

 

 

 

 

ADJUST DAMPER TO THE FULLY OPEN POSITION.

 

 

 

 

 

 

 

 

 

 

1915 W. SAUNDERS ST., MT. PLEASANT, IA 52641.

 

 

 

 

 

 

 

 

Note: An arrow () found in the text signifies change in content.

2

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

!Safety Alert Key:

DANGER! Indicates a hazardous situation which, if not avoidedwill result in death or serious injury.

WARNING! Indicates a hazardous situation which, if not avoidedcould result in death or serious injury.

CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Indicates practices which may cause damage to the fireplace or to property.

Table of Contents

Congratulations!

2

Warranty

4

1 Listing and Code Approvals

6

A.

Appliance Certification

6

B.

Non-CombustibleMaterials

6

C.

Combustible Materials

6

User Guide

2 Operating Instructions

7

A.

Your Fireplace

7

B.

Seasoned Wood

8

C.

Starting a Fire

8

D.

Grate

8

E.

Firescreen

8

F.

Flue Damper

8

G.

Refractory

8

H.

Glass Doors

9

I.

Outside Air (optional)

9

J.

Vented Gas Log Sets & Gas Log Lighters

9

K.

Optional Components

9

L.

Clear Space

9

M.

Wood Fuel

10

3

Maintenance and Service

11

 

A.

Disposal of Ashes

11

 

B.

Chimney Inspection/Cleaning

11

 

C.

Check Firebox Refractory

12

 

D.

Inspect Grate

12

 

E.

Glass Cleaning

12

4

Troubleshooting Guide

13

Installer Guide

5 Getting Started

14

A.

Typical Fireplace System

14

B.

Design and Installation Considerations

15

C.

Draft

15

D.

Negative Pressure

15

E.

Locating Fireplace & Chimney

16

F.

Tools and Supplies Needed

17

G.

Fireplace System Requirements

17

H.

Inspect Fireplace and Components

17

6 Framing & Clearances

18

A.

Select Fireplace Location

18

B.

Clearances

19

C.

Sidewalls/Surrounds

20

D.

Frame the Fireplace

20

7 Installation of Fireplace

21

A.

Things to Consider

21

B.

Unpack the Refractory & Fireplace

21

C.

Position the Fireplace

22

D.

Place Protective Metal Hearth Strips

22

E.

Level Fireplace

22

F.

Install Refractory

23

G.

Install Outside Air Kits

24

8 Chimney Assembly

26

A.

Chimney Requirements

27

B.

Using Offsets/Returns

28

C.

Assemble Chimney Sections

29

D.

Install Chimney Air Kit

29

E.

Install Ceiling Firestops

30

F.

Install Attic Insulation Shield

31

G.

Cut out Hole in Roof

32

H.

Complete Installation

32

I.

Install Flashing

32

J.

Chimney Termination Requirements

33

9 Chase Installations

34

A.

Construct the Chase

34

B.

Install Fireplace & Chimney

35

C.

Install Chase Top

35

D.

Install Termination Cap

35

10

Shrouds

37

 

 

A.

Radiation Shield

37

 

 

B.

Field Constructed Shrouds

37

 

11

Finishing

39

 

 

A.

Non-CombustibleMaterials

39

 

 

B.

Combustible Materials

39

 

 

C.

Hearth Extension

39

 

 

D.

Finishing Material

42

 

 

E.

Combustible Mantel

43

 

 

F.

Sidewalls/Surrounds

44

 

12

Accessories

45

 

 

A.

Gas Log/Lighter Provision

45

 

 

B.

Wood Burning Inserts

45

 

13

Reference Materials

46

 

 

A.

Fireplace Dimensions

46

 

 

B.

Optional Components

47

 

 

B.

Chimney Components

48

 

D.

Service Parts

51

 

E.

Contact Information

52

 

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

3

Warranty

Hearth & Home Technologies Inc.

 

 

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

Parts

Labor

Gas

Wood

Pellet

EPA

Coal

Electric

Venting

Components Covered

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

1 Year

X

X

X

X

X

X

X

covered by Conditions,

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

2 years

 

 

 

 

and glass

 

 

 

 

 

 

 

X

X

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

X

X

 

 

 

Manifold tubes,

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

Burners, logs and refractory

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

X

X

X

 

 

Firebox and heat exchanger

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

X

X

All replacement parts

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

4

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

WARRANTY CONDITIONS:

This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites.

This warranty is only valid while the HHT appliance remains at the site of original installation.

Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the product.

Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this warranty.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur. This is not a flaw and is not covered under warranty.

Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discoloration of glass.

Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.

Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/ incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed constructions, insufficient make-upair supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the appliance.

Non-HHTventing components, hearth components or other accessories used in conjunction with the appliance.

Any part of a pre-existingfireplace system in which an insert or a decorative gas appliance is installed.

HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-

ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of the structure.

This warranty is void if:

The appliance has been over-firedor operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals.Over-firingcan be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes.

The appliance is subjected to prolonged periods of dampness or condensation.

There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

5

1 Listing and Code Approvals

A. Appliance Certification

This fireplace system has been tested and listed in accordance with UL 127 standards by Underwriters Laboratories Inc. for installation and operation in the United States.

This fireplace may be installed in sleeping rooms EXCEPT in manufactured homes. If installed with a gas log set, provisions for the National Fuel Gas Code must be met.

This fireplace has been tested and listed for use with the optional components specified in this manual. These optional components may be purchased separately and installed at a later date. Installation of an outside air kit will require significant reconstruction and is best if installed at the time of fireplace installation.

Heat & Glo is a registered trademark of Hearth & Home Technologies Inc.

Warning! Risk of Fire! Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the following actions.

DO NOT:

install or operate damaged fireplace

modify fireplace

install other than as instructed by Hearth & Home Technologies

operate the fireplace without fully assembling all components

overfire

install an unvented gas log set

installanycomponentnotapprovedbyHearth&Home Technologies

install parts or components not Listed or approved

B. Non-CombustibleMaterials

Materials which will not ignite and burn, composed of any combination of the following:

-

Steel

-

Iron

-

Brick

-

Tile

-

Concrete

-

Slate

-

Glass

-

Plasters

Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube Furnace at 750° C

C. Combustible Materials

Materials made of or surfaced with any of the following materials:

-

Wood

-

Compressed paper

-

Plant fibers

-

Plastic

Any material that can ignite and burn; flame proofed or not, plastered or un-plastered

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified installer, service agency or your dealer.

NoTICE: This fireplace is tested and approved as a decorative fireplace. It should not be factored as a primary heat source in residential heating calculations.

6

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

User Guide

2 Operating Instructions

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fi replace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable materials.

Keep clothing, furniture, draperies and other fl ammable materials away.

If you expect that children may come into contact with this appliance, we recommend a barrier such as a decorative screen. See your dealer for suggestions.

A. your Fireplace

WARNING! DO NOT operate fi replace before reading and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury.

Refractory

Section 2.G.

 

Mantel

 

Grate

 

 

Section 2.D.

 

 

 

 

Gas Log Set

 

 

Gas Log Lighters

 

 

(not shown)

 

 

Section 2.J.

Wood Fuel

 

Firescreen

Section 2.M.

 

(not shown)

 

 

Section 2.E.

 

Hearth

Glass Doors

 

 

 

 

(not shown)

 

 

Section 2.H.

 

 

Clear Space

 

 

Section 2.L.

Outside Air Control

 

Flue Damper

Section 2.I.

 

Section 2.F.

 

UP to Open

 

 

UP to Open

 

 

 

 

DOWN to Close

 

 

DOWN to Close

 

 

 

 

 

 

Figure 2.1 General Operating Parts

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

7

B. Seasoned Wood

Properly seasoned wood is important for successful operation of your fireplace. Most woodburning fireplace problems are caused by burning wet, unseasoned wood.

Seasoned firewood is wood that is cut to size, split and air dried to a moisture content of around 20%.

Imagine a wooden bucket that weighs about eight pounds. Fill it with a gallon of water, put it in the fireplace and try to burn it. This sounds ridiculous but that is exactly what you are doing if you burn unseasoned wood.

A tree cut down a year ago and not split is likely to have almost as high a moisture content now as it did when it was cut.

Please refer to Section 2.M. for more detail.

C. Starting a Fire

NoTICE: You must establish a good draft to prevent smoke spillage into the room.

Warning! Risk of Fire! Keep combustible materials, gasoline and other flammable vapors and liquids clear of the fireplace.

Do NOT:

store flammable materials close to the fireplace

use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace.

Keep all flammable liquids well away from the fireplace while it is in use. Combustible materials may ignite.

The first three or four fires should be of moderate size to allow the oils and binders to be burned from the fireplace and the refractory and paint to cure. You may notice an industrial odor the first few fires. This is considered normal.

Use well-seasonedwood.

Open the flue damper to a fully open position.

Place crumpled or twisted paper under the fireplace grate.

Loosely arrange kindling or small pieces of wood to form a ‘tent’ on the fireplace grate.

Pre-warmthe flue to establish a draft to help reduce smoke spillage duringstart-up.Hold a rolled up piece of burning newspaper under the flue damper for a few moments.

Light the crumpled paper to ignite the kindling.

Add small pieces of wood until a hot bed of embers has been established.

Add a minimum of three average size pieces of split firewood, placed to allow combustion air and flames between them.

Caution! Odors and vapors released during initial operation may be irritating to sensitive individuals.

Open windows for air circulation.

D. Grate

This fireplace is designed to be used with the grate supplied with this unit or one approved by HHT. The grate will break down over time and will need occasional replacement.

Warning! Risk of Fire! Use only thefactory-suppliedintegral grate.

Keeps logs in place.

Allows proper air circulation around the fire.

E. Firescreen

The firescreen is provided to control sparks. Keep it closed when the fireplace is in use.

Warning! Risk of Fire or Burns!

Screen will not prevent burning materials from falling out.

Screen pulls or handles may be hot.

F. Flue Damper

Refer to Figure 2.1 for location of control.

Must be in fully open position (handle up toward the top of the fireplace) during operation of the fireplace.

Before lighting the fireplace, verify fully open position by looking up from the inside of the fireplace.

Warning! Risk of Fire and Asphyxiation! Open damper prior to operating fireplace. A closed damper overfires the fireplace and spills smoke and flames into the room.

G. Refractory

The refractory is supplied to contain heat and provide an attractive interior.

It will break down over time and will need occasional replacement. Small hairline cracks and discoloration are normal and do not affect its safety.

(See refractory maintenance Section 3.C.)

Warning! Risk of Fire! Do not burn fireplace without refractory. Use only refractory supplied by Hearth & Home Technologies, Inc.

8

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

H. Glass Doors

Glass doors are optional.

Refer to Figure 2.2 for how to properly use them.

WARNING! Risk of Fire! Install ONLY doors approved by Hearth & Home Technologies, Inc.

WARNING! Risk of Fire and Smoke! Fireplaces equipped with doors should be operated only with doors fully open or doors fully closed. If doors are left partly open, gas and fl ame may be drawn out of the fi replace opening.

FULLY OPEN

PARTLY OPEN

CORRECT

INCORRECT

FULLY CLOSED

PARTLY CLOSED

CORRECT

INCORRECT

Figure 2.2 Operating Positions of Bi-foldDoors

J. Vented Gas Log Sets & Gas Log Lighters

Optional

Vented gas logs or gas log lighters can be installed in this fi replace. Follow the instructions provided with the accessory for operation.

WARNING! Risk of Fire or Asphyxiation!

DO NOT install unvented gas logs.

Damper must be locked open.

Gas fl ame may generate fumes.

K. Optional Components

Other options may be available

Consult your dealer/distributor

WARNING! Risk of Fire! DO NOT install and or use any component not approved by Hearth & Home Technologies Inc.

L. Clear Space

Do not place combustible objects within areas indicated in Figure 2.3.

WARNING! DO NOT place combustible objects in front of the fi replace. High temperatures may ignite clothing, furniture or draperies.

Mantel - avoid placing candles and other heat-sensitiveobjects on mantel or hearth. Heat may damage these objects.

I. Outside Air (optional)

The outside air kit supplies some combustion air for your fi replace. It may help reduce the effects of negative air pressure. (See Figure 2.1 for location of controls.)

• Refer to Figure 2.1 for location of control

• Close the inlet to prevent cold drafts when the fi replace is not being used.

CAUTION! Risk of Burns! The outside air control handle is HOT when fi replace is in operation. Adjust BEFORE lighting fi re.

48 in. (1219 mm) Clear Space

Front of Fireplace

24 in. (610 mm) Clear Space

Sides of Fireplace

(from the FP opening)

Figure 2.3 Clear Space

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

9

M.Wood Fuel

Hardwood vs Softwood

Your fireplace performance depends on the quality of the firewood you use.

Seasoned wood contains about 8,000 BTUs per pound.

Hard woods are more dense than soft woods.

Hard woods contain 60% more BTUs than soft woods.

Hard woods require more time to season, burn slower and are harder to ignite.

Soft woods require less time to dry, burn faster and are easier to ignite.

Start the fire with soft wood to bring the fireplace up to operating temperature and to establish draft.

Add hard wood for slow, even heat and longer burn time.

Soft woods

Hard woods

Douglas Fir

Oak

Pine

Maple

Spruce

Apple

Cedar

Birch

Poplar

 

 

Aspen

 

 

Alder

 

 

Moisture

Warning! Risk of Fire!

Do NOT burn wet or green wood.

Wet, unseasoned wood can cause accumulation of creosote.

The majority of the problems fireplace owners experience are caused by trying to burn wet, unseasoned wood.

Wet, unseasoned wood requires energy to evaporate the water instead of heating your home, and

Evaporating moisture cools your chimney, accelerating formation of creosote.

Seasoned Wood

Cut logs to size

Split to 6 in. (152 mm) or less

Air dry to a moisture content of around 20%

-Soft wood - about nine months

-Hard wood - about eighteen months

NoTICE:Seasoning time may vary depending on drying conditions.

Storing Wood

Steps to ensure properly seasoned wood:

Stack wood to allow air to circulate freely around and through woodpile.

Elevate wood pile off ground to allow air circulation underneath.

Smaller pieces of wood dry faster. Any piece over 6 in. (152 mm) in diameter should be split.

Wood (whole or split) should be stacked so both ends of each peice are exposed to air. More drying occurs through the cut ends than the sides.

Store wood under cover to prevent water absorbtion from rain or snow. Avoid covering the sides and ends completely.

Warning! Fire Risk! DO NOT store wood:

In front of the fireplace.

In space required for loading or ash removal.

Processed Solid Fuel Firelogs

Manufactured firelogs may be used with this fireplace. Hearth & Home Technologies Inc. recommends the use of UL Classified processed fuel firelogs. Follow the manufacturer’s lighting and safety instructions.

Using firelogs may require more frequent chimney inspection and cleaning.

Do not poke or stir the logs while they are burning. Use only firelogs that have been evaluated for the application in manufactured fireplaces and refer to firelog warnings and caution markings on packaging prior to use.

10

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

3 Maintenance and Service

A. Disposal of Ashes

Frequency: When they reach bottom of grateBy: Homeowner

Warning! Risk of Fire! Ashes could contain hot embers.

Place ashes in a metal container with a tight-fittinglid.

The closed container should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal.

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled.

B. Chimney Inspection/Cleaning

Frequency: At least twice a year during heating season or as recommended by a certified chimney sweep

By: Certified chimney sweep

Warning! Risk of Fire! Ignited creosote is extremely HOT. Prevent creosote buildup.

Refer to Figure 3.1 to remove/reinstall termination caps.

Creosote - Formation and Need for Removal

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burningfire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire.

Warning! Risk of Fire! A chimney fire can permanently damage your chimney system and nearby structures.

In the event of a chimney fire, Hearth & Home Technologies Inc. recommends

replacement of the chimney, and

inspection of the adjacent structure to the provisions of NFPA Level III inspection criteria.

The chimney shall be inspected at least twice a year during the heating season to determine when a creosote buildup has occurred.

When creosote has accumulated it shall be removed to reduce the risk of a chimney fire.

1.REMOVE (8) SCREWS

2.LIFT TOP

Remove 4 screws Remove screws, and lift top pan off. lift top cover.

Top Cover

 

Cap

Cap

Chimney

 

 

Slip

 

Section

Remove 2 screws from

 

the front and back and

 

lift the top off.

TOP

SCREW

TOP

SCREW

TR11/TR11T

ST1175

TCT1175

Round Termination Cap

 

Terra Cotta

Square Termination Cap

Termination Cap

DT SERIES

Figure 3.1 Chimney & Termination Cap Cleaning

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

11

C. Check Firebox Refractory

Frequency: After each ash removal

By: Homeowner

Warning! Risk of Fire! Inspect fireplace refractory. Crumbling, deteriorated refractory can allow overheating of surrounding materials.

Expansion and contraction will cause minor cracking of the refractory. This is normal. The refractory will require periodic replacement depending on use.

The panels should be replaced if

Cracks exceed ¼ inch (6 mm) in width,

Metal is exposed behind the refractory,

Large pieces of refractory fall out.

D. Inspect Grate

Frequency: After each ash removal

By: Homeowner

Inspect grate for:

Warping or sagging 1-1/2in. (38 mm) or more

Broken welds

Burn-throughof grate bars

For safe operation, replace only with an approved grate from Hearth & Homes Technologies Inc.

E. Glass Cleaning

Frequency: As desired

By: Homeowner

CaUTION! Handle glass assembly with care. Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

Do not clean glass while it is hot

Clean glass with a non-abrasivecommercially available cleaner or ashes:

Light deposits

-Use household glass cleaner

Heavy deposits

-Use wood ash on damp cloth or,

-Use commercial fireplace glass cleaner (consult with your dealer)

12

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

4 Troubleshooting Guide

Start Fire Problems

Possible Cause

Solution

Can’t get fire started

Not enough kindling/paper or no

Use dry kindling, more paper. Arrange kindling &

Excessive smoke or spillage

kindling/paper

wood for air movement.

Burns too slowly

 

 

Damper closed/not fully open

Open damper.

Smolders, sizzles

 

 

 

Not enough air for fire to ignite

Check for restricted cap/shroud.

 

 

 

 

 

Open air kit (if installed).

 

 

 

 

 

Check for flue blockage.

 

 

 

 

 

Pre-warmflue before starting fire (refer to starting

 

 

fire section).

 

 

 

 

 

Check for adequate vent height (refer to chimney

 

 

assembly section).

 

 

 

 

 

Open window below the fireplace towards the

 

 

wind.

 

 

 

 

Wood condition is too wet, too

Use dry, seasoned wood (refer to wood fuel

 

large

section).

 

 

 

 

Bed of coals not established

Start with paper & kindling to establish bed of

 

before adding wood

coals (refer to starting fire section).

 

 

 

 

Flue blockage such as birds’

Have chimney inspected for creosote and cleaned

 

nests or leaves in termination

by a certified chimney sweep.

 

cap

 

 

 

 

 

Down draft or negative pressure

Do not use exhaust fans during start-up(refer to

 

Competition with exhaust

negative pressure section).

 

devices

 

 

Open window below the fireplace towards the

 

 

 

 

wind.

 

 

 

Fire burns too fast

Extremely dry or soft wood

Mix in hardwood.

 

 

 

 

 

Mix in less seasoned wood after fire is established

 

 

(refer to wood fuel section).

 

 

 

 

No glass doors

Add glass doors to slow down air flow.

 

 

 

 

Overdrafting

Check for correct vent height; too much vertical

 

 

height creates overdrafting.

 

 

 

 

 

Check location of vent termination (refer to

 

 

chimney assembly section).

 

 

 

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

13

Installer Guide

5 Getting Started

A. Typical Fireplace System

Additional lateral support for chimney above roof (or enclosed in chase) if needed (Section 8)

Non-combustibleroof flashing maintains minimum clearance around chimney

Support straps on rafter support

chimney (not shown)

Ceiling firestop on floor of attic (Section 8)

Chimney system (Section 8)

Combustible framing/header on top of V-shapedstandoffs (Section 6)

Chimney Air Kit (Section 8) Required in Canada. Outlet must be no less than 6 ft. (1.83m) off ground level.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

))))))))

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

))

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

))

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

))

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

))

 

 

 

 

 

)))))))))))))

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outside combustion air

(Section 7) Protective metal hearth strip(s) (Section 7)

Figure 5.1 Typical Fireplace System

NOTICE:

Illustrations and photos reflect typical installations and are for design purposes only.

Illustrations/diagrams are not drawn to scale.

Actual product may vary from pictures in manual.

Termination cap (Section 8 & 9)

Storm Collar (Section 9)

Chimney penetrates roof preferably without affecting

roof rafters (Section 8)

Offset & Return (with hanger straps) (Section 8)

Attic insulation shield (not shown) must be used here to keep

insulation away from chimney if attic is insulated (Section 8)

Framing headed off in ceiling joists (Section 8)

Enclosed space above and around fireplace (Section 6)

Mantel and surround (Section 11)

Decorative facing and trim (Section 11)

Hearth extension (Section 11)

Factory-builtfireplace

14

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

B. Design and Installation Considerations

Notice: Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the fireplace is to be installed

The vent system configuration to be used

Gas supply piping

Electrical wiring

Framing and finishing details

Whether optional accessories—devicessuch as a fan, wall switch or remotecontrol­—aredesired

Notice: Junction box should be installed during initial setup to avoid major reconstruction.

C. Draft

Draft is the pressure difference needed to vent fireplaces successfully. When a fireplace is drafting successfully, all combustion byproducts are exiting the home through the chimney.

Considerations for successful draft include:

Preventing negative pressure

Location of fireplace and chimney

NoTICE: Hearth & Home Technologies assumes no responsibility for the improper performance of the fireplace system caused by:

Inadequate draft due to environmental conditions

Downdrafts

Tight sealing construction of the structure

Mechanical exhausting devices

Improper location of the chimney

D. Negative Pressure

Warning! Risk of Asphyxiation! Negative pressure can cause spillage of combustion fumes and soot. Fire must draft properly for safe operation.

Negative pressure results from the imbalance of air available for the fireplace to operate properly. It can be strongest in lower levels of the house.

Causes include:

Exhaust fans (kitchen, bath, etc.)

Range hoods

Combustion air requirements for furnaces, water heaters and other combustion appliances

Clothes dryers

Location of return-airvents to furnace or air conditioning

Imbalances of the HVAC air handling system

Upper level air leaks such as:

-Recessed lighting

-Attic hatch

-Duct leaks

To minimize the effects of negative air pressure:

Install the outside air kit with the intake facing prevailing winds during the heating season

Ensure adequate outdoor air for all combustion appliances and exhaust equipment

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace

Avoid installing the fireplace near doors, walkways or small isolated spaces

Recessed lighting should be a “sealed can” design

Attic hatches weather stripped or sealed

Attic mounted duct work and air handler joints and seams taped or sealed

Basement installations should be avoided

NoTICE:Hearth&HomeTechnologiesInc.recommends the use of direct vent fireplaces in basements.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

15

E. Locating Fireplace & Chimney

Location of the fireplace and chimney will affect performance.

Install within the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-downof the fire.

Penetrate the highest part of the roof. This minimizes the effects of wind loading.

Locate termination cap away from trees, adjacent structures, uneven roof lines and other obstructions.

Minimize the use of chimney offsets.

Consider the fireplace location relative to floor and ceiling and attic joists.

Take into consideration the termination requirements in Section 8 and Section 9.

NoTICE:Locatingthefireplaceinabasementorinalocation of considerable air movement can cause intermittent smoke spillage from fireplace. Do not locate fireplace near

frequently open doors

central heat outlets or returns

Location NOT recommended:

Not the highest point of the roof

Wind loading possible

Windward

 

Recommended Location:

Recommended Location:

Above peak

• Above peak

Inside heated space

Marginal Location:

Marginal Location:

• Wind loading possible

• Below peak

 

Recommended:

• Insulated exterior chase in cooler climates

Location NOT recommended:

Too close to tree

Below adjacent structure

Lower roof line

Avoid outside wall

Leeward

Multi-levelRoofs

Figure 5.2 Recommended Chimney Locations

16

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

F. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw

Framing material

Pliers

Non-combustiblesealant

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits

Plumb line

Safety glasses

Level

Tape measure

1/2-3/4in. length, #6 or #8self-drillingscrews Misc. screws and nails

G. Fireplace System Requirements

This fireplace system requires:

Refractory Assembly

Grate Assembly

Outside Air Hoods

- Duct must be installed, but sold separately.

H. Inspect Fireplace and Components

Warning! Risk of Fire and/or Explosion! Damaged parts could impair safe operation. Do NOTinstall damaged, incomplete or substitute components. Keep fireplace dry.

Remove fireplace and components from packaging and inspect for damage.

Vent system components and doors are shipped in separate packages.

Report to your dealer any parts damaged in shipment.

Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

17

6 Framing & Clearances

A. Select Fireplace Location

 

74-1/4in.

 

 

 

Note: 1-1/2in. (38 mm) min.

24-3/8in.

 

 

30-3/8in.

distance from sides & back

(1886 mm)

 

 

 

 

(772 mm)

of fireplace to combustible

(619 mm)

 

 

 

 

 

 

 

materials. 1/2 in. (13 mm)

 

 

 

 

 

 

 

 

 

 

min. at nailing flanges.

 

 

 

77 in.

 

Note: In addition to these

 

 

 

(1956 mm)

24 in.

 

 

 

 

framing dimensions,

 

 

 

 

(610 mm)

 

 

Across a

 

also reference the

 

 

 

 

 

 

In an exterior chase

following sections:

 

61-5/8in.

corner

 

 

or projecting into a

Clearances (Section

 

(1565 mm)

 

 

 

garage

 

6.B.)

52-1/2in.

 

 

104-7/8in.

 

 

 

Mantel Projections

(1334 mm)

 

 

 

 

(Section 11.E.)

(2664 mm)

30-3/8in.

 

 

 

 

 

 

Fireplace Dimensions

 

 

(772 mm)

 

 

 

 

 

 

 

(Section 13.A.)

 

 

 

 

 

 

As a room

Along a wall

 

divider 77 in.

77 in.

5/8 in. (16 mm)

(1956 mm)

(1956 mm)

all configurations

48 in.

 

30-3/8in.

(1219 mm)

 

 

 

(772 mm)

24 in.

 

 

(610 mm)

 

 

Figure 6.1 Fireplace Locations (Framing dimensions shown)

18

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

B. Clearances

Warning! Risk of Fire! You must comply with all minimum air space clearances to combustibles as specified in Figure 6.2.Do NOT pack required air spaces with insulation or other materials.

Storm Collar

Roof Flashing

2 in. min.

(51 mm)

(attic)

2 in. min.

(51 mm)

Ceiling Firestop

(roof)

2 in. min.

(51 mm)

Attic

Insulation

Shield

Ceiling Firestop

(ceiling)

2 in. min.

(51 mm)

Offset/Return with

hanger straps

2 in. min.

(51 mm)

0 in. to level of standoffs

0 in. from floor

(ceiling)

2 in. min. Must have 2 in. (51 mm)(51 mm) minimum clearance

to header

1-1/2in. (38mm) from back of appliance

1-1/2in. (38mm) from side of appliance

(except at nailing flanges where it is 1/2 in. (13 mm)

Figure 6.2 Air Space Clearances

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

19

C. Sidewalls/Surrounds

Adjacent combustible sidewalls must be located a minimum of 24 in. (610 mm) from the fireplace opening.

Combustible and non-combustiblemantel legs, surrounds and stub walls may be constructed within the gridded area, Figure 6.3.

Grid represents inch scale.

FLUSH

BRICK

4 in.

[102 mm]

FRONT

FRONT

 

22 3/8 in. [568 mm]

50°

angle

 

50 in.[1270 mm]

60 5/8 in. [1540 mm]

39°

angle

 

19 3/4 in. [502 mm]

 

 

 

 

 

24 in.

24 in.

[610 mm]

[610 mm]

Figure 6.3 Mantel Leg or Wall Projections (Acceptable on both sides of opening)

D. Frame the Fireplace

Figure 6.4 shows typical framing using combustible materials (2x4 lumber shown).

Observe all required air space clearances to combustible materials as shown in Figure 6.1 & 6.2.

Framing across the top of fireplace must be above top standoffs.

2 in. (51 mm) minimum air space clearance to the enclosure.

Framing must be extended straight up, all the way to the ceiling.

61 5/8 in.

(1565 mm)

30 1/2 in.*

(772 mm) * If interior of chase will be drywalled, add the thickness to this measurement.

Fireplace header cannot be positioned until after the fireplace assembly is in place.

Use only non-combustiblematerial below the top of the front standoffs.

8 in. (203 mm) extra space needed (both sides) for outside air connection. If outside air duct has no bend, this dimension may be reduced as long as minimum clearances are met.

Figure 6.4 Framing the Fireplace

20

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

7 Installation of Fireplace

Caution! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

A. Things to Consider

Location of chimney air kit

Location(s) of outside air kits

Electrical connections and/or wall switch

Gas line piping

B. Unpack the Refractory & Fireplace

Remove back refractory from outside of fireplace by bending tabs up and lifting refractory out of brackets. See Figure 7.1.

Bend tabs back down out of the way. See Figure 7.2.

Do not remove screws or refractory brackets from fireplace. If refractory brackets must be removed, fill holes in outer shell with screws.

Repeat this process to remove side refractories.

Figure 7.1 Unpack Back Refractory

Figure 7.2 Bend Refractory Brackets Back Down

Remove screens by removing screw from end of each screen rod.

Figure 7.3 Remove Screen Rods

Remove hearth stone by removing three corrugated shipping spacers (Figure 7.4). Lift hearth stone out of fireplace. See Figure 7.5.

Figure 7.4 Shipping Spacers

Figure 7.5 Lifting Out Hearth Stone

Remove fireplace from pallet:

-Remove screws from shipping brackets and pallet (Figure 7.6),

-Replace screws removed from fireplace.

-Brackets can be used to anchor fireplace in position.

Figure 7.6 Removing Shipping Brackets

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

21

C. Position the Fireplace

Place the fireplace on a continuous flat surface.

Follow framing instructions in Section 6.

Warning! Risk of Fire! Prevent contact with sagging, loose insulation.

DO NOT install against vapor barriers or exposed insulation.

Secure insulation and vapor barriers.

Provide minimum air space clearances at the sides and back of the fireplace assembly as outlined in Section 6.

D. Place Protective Metal Hearth Strips

Warning! Risk of Fire! Protective metal hearth strips MUST be installed.DO NOT cover metal strips with combustible materials. Sparks or embers may ignite flooring.

Refer to Figure 7.7.

Locate the two protective metal hearth strips measuring approximately 26 in. x 4 in. (660 mm x 102 mm) included with this fireplace.

Slide each metal strip 2 in. (51 mm) under front edge of fireplace.

Overlap strips in the middle of fireplace opening by 1 in. (25 mm) minimum..

Metal strips must extend beyond the front and sides of the fireplace opening by at least 2 in. (51 mm).

Protect the front of a platform elevated above the hearth extension with metal strips (not included with fireplace) per Figure 7.8. See Section 11 for hearth extension instructions.

E. Level Fireplace

Level fireplace side-to-sideandfront-to-back.

Shim with non-combustiblematerial as necessary.

Secure fireplace to framing with nailing flanges with a minimum of two fasteners per nailing flange.

Shipping brackets removed in Section B may be (but are not required to be) used to anchor the fireplace to the floor.

Check fireplace opening for square to ensure proper fit of glass doors. Measure diagonals of fireplace opening to make sure they are equal.

1 in. (25 mm) overlap

Protective metal strips are placed 2 in. (51 mm) under the front of the fireplace and must extend beyond the front and sides of fireplace opening by 2 in. (51 mm).

Figure 7.7 Position the Protective Metal Hearth Strips

 

Top piece must overlap

 

bottom piece

 

Raised Platform

2 in.

1 in. (25 mm) min.

(51 mm)

overlap

Floor

2 in.

(51 mm)

Figure 7.8 Protect the Front of an Elevated Platform

22

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

F. Install Refractory

We recommend two installers for hearth stone and refractory installation!

Remove smoke shield by removing five screws (starting from one side: remove two, skip one, remove one, skip one, remove two). See Figures 7.9 and 7.10.

Figure 7.9 Remove Smoke Shield

Fasten in place with the refractory retainer and screws provided. See Figure 7.12.

refractory RETAINER

Figure 7.12 Attach Back Refractory

Note: To ensure proper installation, gas knockouts in the side refractories should be positioned towards back of fireplace. See Figure 7.13.

 

 

Smoke Shield

Front Face

 

Skip

Skip

Remove these screws.

Figure 7.10 Remove Smoke Shield

Place side refractory into fireplace. Position towards front of fireplace and slide to the rear. See Figures 7.13 and 7.14. Repeat for the second side refractory.

Position the bottom of the back refractory to the back of the fireplace and center from side to side. See Figure 7.11. Be sure to position it so the retainer notch is at the top.

Figure 7.13 Install Side Refractory

Figure 7.11 Install Back Refractory

Figure 7.14 Side Refractory Installed

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

23

Slide grate retainers into notches in bottom of back Caution! Risk of Fire or Asphyxiation! Do not draw out- refractory on each side as shown in Figures 7.15 andside combustion air from wall, floor or ceiling cavity, or enclosed

7.16. Place one on each side of back refractory.

Figure 7.15 Slide Grate Retaining Bracket into Notch

Figure 7.16 Grate Retaining Bracket in Place

Replace hearth stone.

Place grate into fireplace and slide back legs into brackets to hold grate in place.

Repalce smoke shield and screen assemblies.

spaces such as an attic or garage.

Do not place outside air hood close to exhaust vents or chimneys. Fumes or odor could be drawn into the room through the fireplace.

Locate outside air inlet to prevent blockage from leaves, snow/ice, or other debris. Blockages could cause combustion air starvation.

3 ft min. from top of uppermost chimney section to air inlet.

 

 

 

)

 

 

 

 

 

 

) )

 

 

 

 

 

 

))

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)))

 

 

 

 

 

 

)

 

 

 

 

 

 

))

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

))))

 

 

 

 

 

 

)

 

 

 

 

 

 

))

 

 

 

 

 

 

))

 

 

 

 

 

 

)))

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

))

 

 

 

 

 

 

))

 

 

 

 

 

 

))

 

 

 

 

 

 

)

 

 

 

 

 

 

))

 

 

 

 

 

 

)

 

 

 

 

 

 

))

 

 

 

 

 

 

)))

 

 

 

 

 

 

))

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

))

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

 

)

 

 

 

 

 

)

 

 

 

 

 

)))))

 

 

 

 

)

 

 

 

 

 

)

 

 

 

 

 

 

 

)

 

 

 

 

 

))

 

 

 

 

))

 

 

 

)))))))))))))

 

 

 

))

 

 

 

 

)

 

 

 

 

 

)

 

 

 

 

 

)

 

 

 

 

 

 

Figure 7.17 Possible Outside Air Inlet Locations

G. Install Outside Air Kits

Refer to Figures 7.17 through 7.21.

Keep duct runs short and straight to minimize restriction. A small dip is acceptable for a cold air trap.

The outside air kit must be installed on both sides of the fireplace.

Locate the outside air hoods in a clear area, preferably into prevailing wind during the heating season. Refer to Figure 5.2 and Figure 7.18.

The air duct may be run vertically.

-The outside air hood must be at least 3 ft (.91 m) below the top of the uppermost chimney section as shown in Figure 7.17.

NO

NO

 

Garage or

NO

Outlet blocked by

combustible

snow, leaves, etc.

liquids storage

Attic space

 

 

NO

 

 

Outlet placed

 

 

higher than 3 ft

 

 

below the

 

 

termination cap

YES

Factory-built

Clear area

fireplace

 

outside

 

 

 

house or in

 

 

ventilated

Use only duct materials specified by manufacturer (preferably

crawl space

 

with short run or mainly straight duct, except small dip for cold

 

air trap which will help prevent flow of cold air).

Figure 7.18 Outside Combustion Air Placement

24

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

Locate outside air kit on one side of fireplace.

Position ring over tabs and screw in place. See Figure 7.21.

Repeat for other side.

Figure 7.19 Close-upof Outside Air Kit

Open door (raise handle up to open, refer to Figure 2.1 for location of handles).

Bend the four tabs out at 90 degrees. See Figure 7.20.

Figure 7.21 Attaching Outside Air Kit Collar

Check the operation by moving the outside air control handles up and down (refer to Figure 2.1).

Mark and cut out a 4 in. (102 mm) hole in the building side for air entry.

Install the outside air hoods in the sidewall of the structure, flush with the building’s exterior.

Assemble the flexible duct (not supplied) between the collar and the outside air hood. Secure into position with the supplied wire ties.

Check for light leaks with a flashlight and seal with duct tape and/or insulation.

Figure 7.20 Bending Tabs on Outside Air Kit Collar

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

25

8 Chimney Assembly

Notice: Chimney performance may vary.

Trees, buildings, roof lines and wind conditions affect performance.

Chimney height may need adjustment if smoking or overdraft occurs.

Chimney must extend beyond combustible roof structure

Maintain minimum height of chimney above roof

Install roof flashing according to minimum requirements

Offsets/returns may not exceed 30° from vertical

Lock chimney sections together firmly to resist movement

Termination Cap

Additional support for tall chimneys

Storm Collar

Maintain minimum clearances to combustibles as specified

Support straps for returns must be secured to adequate framing

Offsets and returns must be secured with the screws provided (outer pipe only)

Ceiling firestops are required where chimney passes through ceiling orfloor

Figure 8.1 Typical Chimney System - Guidelines for Chimney System Installation

26

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

A. Chimney Requirements

Measure vertical distances from the base of the fireplace as shown in Figure 8.2.

• Minimum overall straight height

20 ft

(6.1 m)

• Minimum height with offset/return

20.5 ft

(6.25 m)

• Maximum height

90 ft

(27.43 m)

• Maximum chimney length between an offset

20 ft

(6.1 m)

and return

 

 

• Maximum distance between chimney

35 ft

(10.67 m)

stabilizers

 

 

• Double offset/return minimum height

24 ft

(7.32 m)

• Maximum unsupported chimney length

6 ft

(1.83 m)

between the offset and return

 

 

• Maximum unsupported chimney height above

35 ft

(10.67 m)

the fireplace

 

 

• Maximum unsupported chimney above roof

6 ft

(1.83 m)

Warning! Risk of Fire! You must maintain 2 in. (51 mm) air space clearance to insulation and other combustible materials around the chimney system. Failure to do so may cause overheating and fire.

Determine the chimney components needed to complete your particular installation:

Measure the total vertical height of the fireplace installation from the base of the fireplace assembly to the approximate location of the bottom of the termination cap.

Subtract the effective height of the fireplace assembly (see Figure 8.2) from the total vertical height to determine the overall height of the chimney installation.

Create a schematic for your application similar to Figure 8.2 showing components required (referring to Table 8.1). Figure 8.1 identifies those components and where used.

Installaceilingfirestopwheneverthechimneypenetrates a floor/ceiling.

Notice: A maximum of two pairs of offsets and returns may be used.

Caution! Risk of Fire and/or Asphyxiation! DO NOT connect this fireplace to a chimney flue servicing another appliance. Do NOTconnect to any air distribution duct or system. These actions could cause overheating/fire in the chimney flue, or release of exhaust fumes into the living areas.

Table 8.1

HEIGHT OF CHIMNEY COMPONENTS

in.

mm

Chimney Stabilizer

 

 

 

SL11

4-3/4

121

Ceiling Firestops

 

 

 

FS538

0

0

 

FS540

0

0

 

 

 

 

Offsets/Returns

 

 

 

SL1130

18

457

Roof Flashing

 

 

 

RF570

0

0

 

RF571

0

0

Chimney Sections*

 

 

 

SL1106

4-3/4

121

 

SL1112

10-3/4

273

 

 

 

 

 

SL1118

16-3/4

425

 

SL1136

34-3/4

883

 

SL1148

46-3/4

1187

* Dimensions reflect effective height.

 

 

6 ft (1.83 m) max. unsupported chimneyabove roof

Ceiling Firestop

68-1/8in.

 

(1730 mm)

 

Effective Height

Gas

(bottom of fireplace

Knockout

to top of starter collar)

35 ft (10.67 m) max. straight unsupported chimney height

20.5 ft (6.25 m) min. height/single offset-return

24 ft. (7.32 m) min. height/double offset-return

90 ft (27.43 m) max. height

Figure 8.2 Chimney Requirements

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

27

B. Using Offsets/Returns

Use an offset/return to bypass overhead obstructions.

An offset and return can be used as a single entity or separated by chimney section(s).

Warning! Risk of Fire! Do not use offset/returns greater than 30°. Chimney draft will be restricted and could cause overheating and fire.

Measure the shift needed to avoid the overhead obstruction. Refer to dimension A in Figure 8.3.

Find the appropriate A dimension listed in Table 8.2.

The B dimension coinciding with the A dimension measurement in Table 8.2 represents the required vertical clearance needed to complete the offset/return.

Read across the chart to find the number of chimney sections/model numbers needed between the offset and return.

A

B

1-1/4in. (32 mm) OVERLAP

Figure 8.3 Chimney Offset/Return

Example:

Your “A” dimension from Figure 8.3 is 14 1/2 in. (368 mm). Using Table 8.2 the dimension closest to, but not less than 14 1/2 in. (368 mm) is 15 3/4 in. (400 mm) using a 30° offset/return.

You determined from the table that you would need 36 5/8 in. (930 mm) (Dimension “B”) between the offset and return.

The chimney component that best fits your application is two SL1112s.

Table 8.2

 

A

 

B

 

 

 

 

 

in.

 

mm

in.

 

mm

SL1106

SL1112

SL1118

SL1136

SL1148

4 7/8

 

124

17 7/8

 

454

-

-

-

-

-

7 1/4

 

184

22

 

559

1

-

-

-

-

 

 

 

 

 

 

 

 

 

 

 

9 3/4

 

248

26 1/8

 

664

2

-

-

-

-

10 1/4

 

260

27 1/4

 

692

-

1

-

-

-

12 3/4

 

324

31 3/8

 

797

1

1

-

-

-

 

 

 

 

 

 

 

 

 

 

 

13 1/4

 

337

32 3/8

 

822

-

-

1

-

-

15 3/4

 

400

36 5/8

 

930

-

2

-

-

-

 

 

 

 

 

 

 

 

 

 

 

18 1/8

 

460

40 3/4

 

1035

1

2

-

-

-

18 3/4

 

476

41 3/4

 

1060

-

1

1

-

-

 

 

 

 

 

 

 

 

 

 

 

21 3/4

 

552

47

 

1194

-

-

2

-

-

22 1/4

 

565

4 8

 

1219

-

-

-

1

-

24 3/4

 

629

52 1/8

 

1324

1

-

-

1

-

27 3/4

 

705

57 3/8

 

1457

-

1

-

1

-

28 1/4

 

718

58 3/8

 

1483

-

-

-

-

1

 

 

 

 

 

 

 

 

 

 

 

30 3/4

 

781

62 1/2

 

1588

1

-

-

-

1

33 3/4

 

857

67 3/4

 

1721

-

1

-

-

1

 

 

 

 

 

 

 

 

 

 

 

36 3/4

 

933

73

 

1854

-

-

1

-

1

39 3/4

 

1010

78 1/8

 

1984

-

-

-

2

-

41 1/8

 

1045

82 3/8

 

2092

1

-

-

2

-

45 3/4

 

1162

88 1/2

 

2248

-

-

-

1

1

48 1/8

 

1222

92 3/4

 

2356

1

-

-

1

1

 

 

 

 

 

 

 

 

 

 

 

51 3/4

 

1314

98 7/8

 

2511

-

-

-

-

2

Proper assembly of air cooled chimney parts results in an overlap of chimney joints of 1-1/4in. (32 mm). Effective length is built into this table.

28

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

C. Assemble Chimney Sections

Warning! Risk of Fire! Do NOT install substitute or damaged chimney components.

Use only those components described in this manual.

Substitute or damaged chimney components could impair safe operation and cause overheating and fire.

Support the pipe during construction and check to be sure inadvertent loading has not dislodged the chimney section from the fireplace or at any chimney joint.

Attach a straight chimney section or an offset to the top of the fireplace.

Placeinnerfluetotheinsideofthechimneysectionbelow it. Place the outer casing outside the outer casing of the chimney section below it. Refer to Figure 8.4.

NoTICE: Chimney sections cannot be disassembled once locked together. Plan ahead!

Lock chimney sections and/or offsets/returns together by pushing downward until the top section meets the stop bead on the lower section.

Pull on the top section to make sure it is fully engaged and will not separate.

You may use #6 or #8 sheet metal screws no longer than 1/2 in. (13 mm) to fasten chimney sections together. Do NOT penetrate inner flue.

Warning! Risk of Fire! You MUST use screws (provided) to fasten offset/returns to chimney sections to keep the chimney parts from twisting. Failure to do so could cause fire.

Fasten offset/returns to chimney sections. Insert the screws (provided) through the predrilled holes. Do NOT penetrate inner flue.

Secure chimney returns with hanger straps provided; fasten to studs or joists.

Verticalstraightrunsofchimneymustbesupportedevery 35 ft (10.7 m).

D. Install Chimney Air Kit

Required in Canada.

Follow instructions provided with this accessory.

Figure 8.4 Assembling Chimney Sections

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

29

E. Install Ceiling Firestops

Caution! Risk of Fire! Ceiling firestops must be used whenever the chimney penetrates a ceiling/floor.

Chase construction requires ceiling firestops at each floor or every 10 ft (3.05 m) of clear space.

The ceiling firestop slows spread of fire and reduces cold air infiltration.

Install a ceiling firestop whenever chimney penetrates ceiling/floor.

Mark and cut an opening in ceiling as shown in Figure 8.5.

Frame the opening with the same size lumber used in the ceiling joists.

Nail the ceiling firestop to the bottom of the ceiling joists when there is a room above.

Use an attic insulation shield if the ceiling is insulated. The ceiling firestop may then be attached above or below the joists.

Warning! Risk of Fire! Do NOT seal area between firestop opening and chimney pipe except where they enter the attic or leave the warm air envelope of the home (use 600° F sealant).

ROOM ABOVE (non-insulatedceiling)

B

A

Ceilng firestop frombottom

ATTIC ABOVE (insulated ceiling)

Ceiling firestop from top

Note: Use same dimensional lumber for framing ceiling firestop and joists.

 

 

A

 

B

Catalog #

in.

 

mm

in.

 

mm

FS538

17

 

432

17

 

432

FS540

17

 

432

26

 

660

Figure 8.5 Installing the Ceiling Firestop

30

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

F. Install Attic Insulation Shield

Warning! Risk of Fire! You MUST install an attic insulation shield when there is any possibility of insulation or other combustible material coming into contact with the chimney.

Do NOT pack insulation between the chimney and the attic insulation shield.

Failure to keep insulation and other materials away from chimney pipe could cause fire.

Do NOT offset chimney inside insulation shield.

Installation of a ceiling firestop is required

Refer to Figures 8.6 - 8.8.

Roll the shield (around the chimney if already installed) until you have a 3 in. (76 mm) overlap and the three holes on each side match up (large holes on top).

Insert three screws into the matching holes to form a tube.

Bend three tabs on the bottom of the tube inward to 90° to maintain chimney air space (refer to Figure 8.6).

Rest the insulation shield on the ceiling firestop below.

Bend the three short tabs at the top of the shield inward to 90° to maintain the 2 in. (51 mm) air space from the chimney.

Bend the remaining top tabs to just meet the pipe.

If you wish to make a custom shield or barrier, follow these guidelines:

Metal is preferred, although any material stiff enough to hold back the insulation can be used.

Warning! Risk of Fire! Use of cardboard or other materials that can deflect under humidity or other environmental conditions is not recommended.

The shield or barrier must be tall enough to extend above the insulation and prevent blown-ininsulation from spilling into the cavity.

Maintain specified air spaces around chimney.

Check instructions and local codes for further details.

 

Bend remaining tabs

 

to rest against pipe to

Bend inward

prevent insulation

90°

from falling in.

 

Insert three

 

screws

3 in. (76 mm) overlap

Figure 8.6 Prepare Attic Insulation Shield

 

 

Tabs bent in to

 

Pipe

rest against pipe

 

 

 

 

Attic Insulation Shield

 

 

17 in. (432 mm)

 

6 Tabs bent

diameter

 

in 90°

Ceiling Firestop

 

 

Insulation

Pipe

Insulation

13 in.

(330 mm)

Figure 8.7 Install Attic Insulation Shield (firestop above ceiling)

 

 

Tabs bent in to

 

 

rest against pipe

 

Pipe

 

 

 

Attic Insulation Shield

 

 

17 in. (432 mm)

 

 

diameter

 

6 Tabs bent

 

 

in 90°

 

Insulation

 

Insulation

13 in.

Pipe

Ceiling Firestop

(330 mm)

 

 

Figure 8.8 Install Attic Insulation Shield (firestop below ceiling)

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

31

G. Cut out Hole in Roof

Refer to Figure 8.9.

Plumb from roof to center of chimney.

Drive a nail up through roof to mark center of pipe.

Measure to either side of nail and mark the 17 in. x 17 in. (432 mm x 432 mm) opening required.

Measure opening on the horizontal; actual length may be larger depending on roof pitch.

Cut out and frame opening.

Refer to Chapter 25of the Uniform Building Codefor roof framing details.

H. Complete Installation

Warning! Risk of Fire! You MUST maintain 2 in. (51 mm) air space to insulation and other combustible materials around the chimney system. Failure to do so could cause overheating and fire.

Keep chimney sections from separating or twisting.

You may secure straight chimney sections at the joints with screws no longer than 1/2 in. (13 mm).

The following steps should be skipped if using a chase:

Install roof flashing appropriate to roof pitch.

Install round termination cap and storm collar.

I. Install Flashing

Assemble chimney so it passes through the framed opening.

Slip the flashing over the chimney.

Notice: Roofing shingles must be below the flashing plate on the lower side of a sloped roof and over the flashing plate on the sides and top.

Nail the flashing to the roof. Keep gaps between the flashing plate and the roof to a minimum.

Caulk the flashing plate and roof junction as well as the vertical seam on the flashing. All nail heads must be caulked with a roofing sealant.

Figure 8.9 Ceiling/Attic Construction

32

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

J. Chimney Termination Requirements

Install a cap approved and listed for this fireplace system.

Locate cap where it will not become plugged by snow or other materials.

Locate cap away from trees or other structures.

The bottom of the termination cap must be at least 3 ft (.91 m) above the roof AND at least 2 ft (.61 m) above any portion of roof within 10 ft (3.05 m) as shown in Figure 8.10.

The distance required between caps is shown in Figure 8.10.

Slanted Roofs

Chimney must extend 3 ft (.9 m) above the roof

Flat Roofs

Chimney must extend 3 ft (.9 m) above the roof

Chimney must extend 2 ft (.6 m) above any portion of the roof or adjacent structures within

10 ft (3 m) of the chimney

Chimney must extend 2 ft (.6 m) above any portion of the roof or adjacent structures within

10 ft (3 m) of the chimney

Multiple Chimney Locations

Gas, Wood or Fuel Oil

Termination Cap

A

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 in. (minimum) up to 20 in.

18 in. minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

152 mm/508 mm

457 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

Wood

 

20 in. and over

0 in. minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum

 

 

 

 

 

 

 

 

 

A *

 

 

 

 

 

 

(See

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

illustration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

above)

Gas

Termination

Cap **

Perpendicular Wall

* If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

** In a staggered installation with both gas and wood terminations, the wood termination cap must be higher than the gas termination cap.

Figure 8.10 Multiple Chimney Locations

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

33

9 Chase Installations

A. Construct the Chase

A chase is a vertical boxlike structure built to enclose the fireplace and/or its vent system. Vertical chimneys that run on the outside of a building must be installed inside a chase.

Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked.

A chase should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner. All outer walls need to be insulated.

Building codes require false ceiling and ceiling firestops at each floor of the chase or every 10 ft (3.05 m) of clear space to control spread of fire.

Walls, ceiling, base plate and cantilever floor at the first level of the chase should be insulated. See Figure 9.1. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, Hearth & Home Technologies recommends that the inside surfaces be sheet rocked and taped (or the use of an equivalent method) for maximum air tightness.

Round Termination Cap

 

Metal Chase Top

 

 

Ceiling

 

 

Firestop

 

 

False Ceiling

 

 

Attic

 

Tabs

Insulation

 

Shield

 

 

 

 

Ceiling

Insulation in the

 

outside walls

 

Firestop

 

of the chase

 

 

Insulation

Insulation

 

False Ceiling

False Ceiling

 

 

Chimney

 

Figure 9.1

Chase Assembly

 

Gas line holes and other openings should be caulked with high temperature caulk or stuffed with unfaced fiberglass insulation. If the fireplace is being installed on a cement slab, we recommend that in cold climates, a sheet of plywood or other raised platform be placed underneath to prevent conducting cold up into the room.

Three examples of chase applications are shown in Figure 9.2.

1.Fireplace and chimney enclosed in an exterior chase.

2.Chimney offset through exterior wall and enclosed in chase.

3.Chase constructed on roof.

Note: In cooler climates, all chase walls should be insulated.

1

2

3

Figure 9.2 Chase Constructions

Warning! You must install false ceilings and ceiling firestops at each floor of the chase or every 10 ft (3.05 m) to control spread of fire.

Warning! Risk of Fire! Do not seal area between fire stop opening and chimney pipe. Restricting air flow around chimney may cause fire.

Warning! Risk of Fire! You must maintain a minimum 2 in. (51 mm) air space clearance to insulation and other materials surrounding the chimney system.

Insulation and other materials must be firmly secured to prevent accidental contact with chimney system.

The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fireplace or chimney.

Failure to prevent contact between insulation or other materials and chimney system may cause overheating and fire.

34

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

B. Install Fireplace & Chimney

Install as per Sections 7 and 8.

C. Install Chase Top

You MUSTuse a chase top in a chase installation. Chase tops are available from your Heat & Glo dealer or may be field constructed.

Include a turndown and drip edge to prevent water from seeping into the chase.

Include a 2 in. (51 mm) soldered, caulked or spun collar around pipe opening to keep water out.

Provide a 1/8 in. (3 mm) gap around the flue pipe.

Slope the chase top downward away from the opening.

Caution! Do not caulk the pipe to the chase top collar.

Caulk all seams to prevent leaks.

Refer to Figure 9.4.

Slope Downward (1/4 in. per foot minimum)

2 in. (51 mm) Collar on Chase Top

Turn-down

Drip Edge

Chase

.018 (26 ga) min. Galvanized Chase Top

Figure 9.3 Chase Top Construction

D. Install Termination Cap

Install the chimney sections up through the chase enclosure.

Refer to termination cap instructions.

Warning! Risk of Fire! The minimum overlap of cap to pipe (as shown in the following illustrations) MUST be met or chimney may separate from cap. Separation allows sparks, heat and embers to escape.

Notice: Paint the termination cap with arust-resistantpaint to protect against the effects of corrosion on those parts exposed to the weather.

TR11 Round Termination Cap

Slip storm collar

around chimney pipe before termination cap pipe is snapped into the chimney pipe.

Caulk gaps between storm collar & pipe, and storm collar

& chase top.

Collar

2 in. (51 mm) Minimum Height

Chase Top

Termination

Cap

Storm

Collar

Chimney

Pipe

Do NOT block air holes

6 in. (153 mm) Minimum top of chase to top of chimney pipe

Chase

Termination cap pipe and chimney section must be snapped together to maintain an overlap of 1-1/2in. (38 mm).

Figure 9.4 Installing a TR11 Round Termination Cap

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

35

TR11T Round Telescoping Termination Cap

Assemble storm collar around extended termination cap pipe

once cap is installed.

Caulk gaps between storm collar & pipe, and storm collar

& chase top.

Collar

2 in. (51 mm) Minimum Height

Chase Top

Termination

Cap

Do NOT block air holes

Storm

Collar

3 clip brackets. Slip over chase collar and attach with screws provided.

14 1/2 in. (368 mm) Maximum

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2in. (38 mm)

Figure 9.5 Installing a TR11T Round Telescoping Termination

Cap

ST1175 Square Termination Cap

Flange

Termination Cap

Collar

2 in. (51 mm) Minimum Height

Chase Top

Chimney

Pipe

Place waterproof caulk or sealer under each flange of the termination cap and on top of each screw to help prevent leaks.

The last section of pipe must stop between 2 in. (51 mm) above the top of the chase and 4 3/4 in. (121 mm) below the top of the chase.

2 in. (51 mm) maximum

4 3/4 in. (121 mm) maximum

Chase

Termination cap pipe and chimney section must overlap 1-1/2in. (38 mm)

Figure 9.6 Installing an ST1175 Square Termination Cap

TCT1175 Terra Cotta Cap

 

Place waterproof sealer

Remove 2 screws

under each flange of the

termination cap and on

from front & back

top of each screw to

to lift the top off

help prevent leaks.

 

Termination Cap

The last section of pipe

 

must stop between 2 in.

 

(51 mm) above top of

Collar

chase and 7 in. (178 mm)

below top of chase

2 in. (51 mm)

 

Minimum Height

 

Chase Top

2 in. (51 mm)

 

7 in. (178 mm)

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2in. (38 mm)

Figure 9.7 Installing a TCT1175 Terra Cotta Cap

36

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

10 Shrouds

A. Radiation Shield

Some shrouds require a radiation shield. Use where specified.

Radiation shield must be constructed of minimum 26 ga sheet metal.

B. Field Constructed Shrouds

Warning! Risk of Fire! Shrouds must be constructed as specified. Improper construction may overheat chase top.

Chase top shrouds may be field constructed where permitted by regional building codes.

NoTICE:Some regional codes require anagency-Listedshroud. Consult your local building officials.

Hearth & Home Technologies Inc. supplies UL listed shrouds. See your dealer for details.

The following field constructed shroud designs have been tested for Hearth Technologies fireplace systems and termination caps.

The shrouds must be constructed from a minimum .018 in. (26 ga) thick aluminized steel.

Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap

3 in. (76 mm) tall legs

Length x Width to fit inside shroud

Figure 10.1 Radiation Shield

The wire mesh is optional but recommended and must be .018 in. thick minimum, 1/2 in. mesh.

Open Top Shroud (TR11/TR11T caps require radiation shield)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top Dim.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top Dim.

 

 

 

 

 

 

 

 

 

 

 

Min. Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Width

 

 

 

3 in (76 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

minimum

 

 

 

 

 

 

Min. Opening

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Width

 

 

 

 

 

 

 

Base Dim.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

TR11/11T

 

TR11/11T TV

 

 

 

 

 

 

 

 

 

 

Base Dim.

 

 

 

 

 

 

 

 

 

 

 

 

Min. Base Dims.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in

32 x 32

 

26 x 26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

813 x 813

 

660 x 660

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Radiation Shield

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Required

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. Top Dims.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in

29 x 29

 

23 x 23

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

737 x 737

 

584 x 584

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min. Opening Width

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in

26 x 26

 

20 x 20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

660 x 660

 

508 x 508

Figure 10.2 Open Top Shroud Dimensions

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

37

Mailbox Style Shroud (radiation shield required)

3 in. (76 mm) Min. Opening Height

Min. Height above radiation

shield

Min. Base Dim

Min.

 

 

 

 

 

Base Dim

 

Min. Opening Width

 

TR11/11T

TR11/11T TV

 

 

 

 

 

 

 

Min. Base Dims.

 

3 in. (76 mm) Min.

 

 

in

34 x 34

28 x 30

Radiation Shield Height

 

 

 

mm

864 x 864

711 x 762

 

from top of Chase

 

 

 

Min. Height Above Radiation Shield

 

 

 

in

21-1/4

20-1/2

 

 

 

 

 

 

 

 

 

mm

540

521

 

 

 

 

Min. Opening Width

 

 

 

in

28 x 28

22 x 24

Figure 10.3 Mailbox Style Shroud Dimensions

mm

711 x 711

559 x 610

 

 

 

Roofed Style Shroud (radiation shield required)

Minimum

Height above

Radiation Shield

3 in. (76 mm) Radiation

Shield Height

Min.

 

Minimum

Termination

Opening

Height

Cap

 

Radiation Shield

Chase Top

Base Dimension

Minimum

Base Dimension

Min. Opening Width

 

TR11/11T

TR11/11T TV

 

 

Min. Base Dims.

 

in

34 x 34

34 x 34

 

 

 

 

 

mm

864 x 864

864 x 864

 

Min. Height Above Radiation Shield

 

in

16

16

 

mm

406

406

 

 

Min. Opening Width

 

in

28

28

 

mm

711

711

 

 

Min. Opening Height

 

in

12

12

 

 

 

 

 

mm

305

305

Figure 10.4 Roofed Style Shroud Dimensions

38

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

11 Finishing

A. Non-combustibleMaterials

Materials which will not ignite and burn, composed of any combination of the following:

-

Steel

-

Iron

-

Brick

-

Tile

-

Concrete

-

Slate

-

Glass

-

Plasters

Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube Furnace at 750° C

B. Combustible Materials

Materials made of or surfaced with any of the following materials:

-

Wood

-

Compressed paper

-

Plant fibers

-

Plastic

Any material that can ignite and burn; flame proofed or not, plastered or un-plastered

C. Hearth Extension

WARNING! Risk of fire! High temperatures, sparks, embers or other burning material falling from the fireplace may ignite flooring or concealed combustible surfaces.

Protective metal hearth strips MUST be installed.

Hearth extensions MUST be installed exactly as specified.

Table 11.1

R = 1/k x inches of thickness

You MUST use a hearth extension with this fireplace.

This fireplace has been tested and approved for use with a hearth extension insulated to a minimum R value of 1.03.

The hearth extension material MUST be covered with tile, stone or other non-combustiblematerial.

Manufactured hearth materials will usually have a published R value (resistance to heat) ork value (conductivity of heat). Refer to the formula in Table 11.1 to convert a k value to an R value,

Refer to Table 11.2 for hearth extension insulation alternatives.

12 in.

 

(305 mm)

 

50 in.

12 in.

(1270 mm)

(305 mm)

 

74 in.

 

(1880 mm)

 

 

Raised Hearth

 

20 in. (508 mm)

 

minimum

 

Flush Hearth

Figure 11.1 Hearth Extension Dimensions

30 in. (762 mm)

minimum

Table 11.2

Hearth Extension Insulation Alternatives-Totalminimum R Value must equal 1.03

 

 

 

Minimum

 

k per inch

r per inch

thickness

Material

thick

thick

required

Hearth & Home HX3, HX4 (Micore 300™)

0.49

2.06

1/2 in.

 

 

 

 

USG Micore 160™

0.39

2.54

1/2 in.

USG Durock™ Cement Board

1.92

0.52

2 in.

Cement Mortor

5.0

0.20

5-1/8in.

 

 

 

 

Common Brick

5.0

0.20

5-1/8in.

Ceramic Tile

12.50

0.08

12-1/4in.

 

 

 

 

Armstrong™ Privacy Guard Plus

0.46

2.18

1/2 in.

Marble

14.3-20.0

0.07-0.05

14-5/8in. -20-3/8in.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

39

Raised Hearth Extension Framing

The hearth framing must be constructed of non-combusti-ble materials and placed on an HX4 or equivalent material (Figures11.2-11.4).When creating the platform, allow for the thickness of thenon-combustiblefinishing materials (Figure 11.5).

IMPORTANT! Hearth extension design must be determined before installation of fireplace.

 

Continuous,

 

 

 

non-combustiblesealant

Fireplace

 

1/2 in. Micore

Tile, stone or other

 

or equivalent

 

non-combustiblematerial

Protective

insulation

(see Table 11.2)

 

 

Metal Hearth

 

 

 

Strip

2 in. (51 mm) Floor constructed of wood or required other combustible material

Figure 11.2 Hearth Extension Construction

20 in. Min. Hearth Extension

Non-combustible

Finishing Material

Non-combustible

Framing Material

1/2 in. Micore

 

 

 

 

 

 

 

 

Protective Metal

Floor

or equivalent

insulation

Hearth Strips

 

 

 

 

 

 

Figure 11.3 Raised Platform Hearth Extension Detail

Non-combustible

Framing Material

Hearth mustextend at least12 in. beyond

the fireplace opening on both sides.

1/2 in. Micore or equivalent

20 in. Min.

Figure 11.4 Raised Platform Hearth Extension-FramingMaterials

Non-combustible

Finishing Materials

Figure 11.5 Raised Platform Hearth Extension-FinishingMaterials

40

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

Non-combustibleSealant

After completing the framing and applying the facing materials over the framing, a bead of non-combustiblesealant must be used to close off any gaps at the top and sides between the fireplace hearth.

Non-combustibleSealant

Figure 11.6 Place Non-combustibleSealant

Flush Hearth Extension Framing

A raised hearth extension built flush with the fireplace opening (Figures 11.7, 11.8) requires the fireplace to be installed on a non-combustiblesurface.

12 in.

 

 

Min.

12 in.

30 in. min.

 

 

 

 

Min.

 

Figure 11.7 Flush Hearth Extension

 

 

Note: The bottom of the fireplaceopening is7-5/8in. above the bottomof the fireplace. Finished hearth mustNOT extend above this level.

Finished

Floor 30 in. Min.

Hearth Extension

Micore

Non-combustibleMaterial

Protective Metal

 

 

Hearth Strip

Figure 11.8 Flush Hearth Extension Side View

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

41

D. Finishing Material

Refer to Sections 11.A. and Sections 11.B. for combus- tible/non-combustiblematerials. Refer to Figure 11.9 fornon-combustiblezone.

Warning! Risk of Fire! You must maintain clearances.

Use only non-combustibleframing material below standoffs.

Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in the non-combustiblezone.

Do NOT cover metal fireplace front with combustible materials.

Install combustible materials only to specified clearances on top front and side edges.

Complete framing and apply facing material (drywall) over framing.

Abead of 300-degF minimumnon-combustiblesealant must be used to close off any gaps at the top and sides between the fireplace and facing to prevent cold air leaks.

These surfaces

 

may be covered

 

with non-combustible

 

material.

Non-combustible

 

 

sealant.

Figure 11.9 Non-combustibleFacing

 

Large gaps can be bridged with fiberglass rope gasket.

Only non-combustiblematerials may be used to cover the metal fireplace front.

Finished combustible wall Flat 2 x 4 stud wall

2 x 4 header, flush with front of stand-offs

Combustible material

Non-combustibledecorative facing(up to full brick depth)

Continuous, non-combustiblesealant

Tile, stone or other non-combustiblematerial

1/2 in. Micore or equivilent insulation

Figure 11.10 Decorative Facing

Metal strips are placed 2 in. (51 mm) under the front of the fireplace and must extend beyond the front and sides of fireplace opening by 2 in. (51 mm)

Floor constructed of wood or other combustible material

42

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

E. Combustible Mantel

Refer to shaded areas of Figure 11.11 for locations and dimensions of combustible mantels

A combustible mantel may be positioned no lower than 20 in. (508 mm) above the top of the fireplace opening.

A combustible mantel may have a maximum depth of 12 in. (305 mm).

Combustible trim and materials cannot be placed within 6 in. (152mm) of the fireplace opening (top or sides).

Combustible materials projecting more than 1 1/2 in. (38 mm) shall not be placed within 12 in. (305 mm) from the top of the fireplace opening.

Combustible trim must not cover the metal surfaces of the fireplace.

Mantel clearance is in accordance with Section 7-3.3.3 ofANSI/NFPA211.

Combustible Wall

Combustible

7 ft (2134 mm)

minimum

 

Decorative Facing

base of fireplace

 

 

to ceiling

 

12 in./305 mm

 

 

Mantel

 

2 x 4 stud wall

 

 

 

20 in./508 mm

 

 

minimum

 

Front Standoffs

 

 

Non-combustible

12 in./305 mm

 

Decorative Facing

minimum

 

 

 

such as: Steel, iron,

 

 

brick, tile, concrete,

 

 

slate, tile, plasters

6 in./152 mm

 

1 1/ 2 in./38 mm

minimum

 

 

 

maximum

 

 

 

Measured from top of fireplace opening

Seal joint with

Grid represents 1 in. squares

non-combustible

 

sealant

 

Figure 11.11 Clearances to Mantels or other Combustibles above Fireplace

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

43

F. Sidewalls/Surrounds

Adjacent combustible sidewalls must be located a minimum of 24 in. (610 mm) from the fireplace opening.

Combustible or non-combustiblemantel legs, surrounds and stub walls may be constructed per Figure 11.12.

4 in. [102 mm]

 

 

 

19 3/4 in. [502 mm]

 

 

 

 

 

 

BRICK FRONT

39°

angle

24in.

[610mm]

 

 

 

 

 

 

 

Grid represents inch scale.

FLUSH FRONT

50 in. [1270 mm]

60 5/8 in. [1540mm]

 

 

 

 

 

 

 

 

angle

50°

3/822[568 in.mm]

24 in. [610 mm]

Figure 11.12 Mantel Leg or Wall Projections (acceptable on both sides of opening)

44

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

12 Accessories

A. Gas Log/Lighter Provision

Warning! Fire and/or Asphyxiation Risk! Use with solid wood fuel or decorative gas appliance only. Gas fire generates fumes.

DO NOT install unvented gas logs

Damper must be locked fully open when gas logs are installed

A certified gas log lighter or decorative gas log set can be installed in this fireplace.

Maximum input is 100,000 BTU/hr.

Decorative gas appliance must be certified to ANSI Z21.60 “Standard for Decorative Gas Appliances for Installation in Vented Fireplaces”.

Must be installed in accordance with the National Fuel

Gas Code, ANSI Z223.1.

A gas log set must incorporate a gas shutoff.

Gas log set requires the damper to be locked fully open.

A listed automatic damper system with safety interlock may be used in this fireplace with only compatible, listed gas log sets. See damper system manufacturer’s insturctions.

Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe.

Seal refractory around pipe with fireplace mortar or a non-combustiblesealant.

Firebox

Refractory

Seal with fireplace mortarornon-combust-ible sealant

Gas line

Repack insulation knockout

Outer shell of fireplace

Maintain air clearanceto combustibles.

Combustible materials

Gas line

4 in.(102 mm)

1 1/2 in. (38 mm) air space around

pipe

Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side.

Figure 12.1 Gas Line Installation

B. Wood Burning Inserts

Warning! Risk of Fire! Improper installation of wood inserts may cause fireplace or chimney system to overheat.

If a wood burning insert is being installed in this fireplace, Hearth & Home Technologies recommends full reline of the chimney.

Cooling air openings at the top of the chimney must not be obstructed in any manner.

Hearth & HomeTechnologies recommends securing the reline at the top of the flue and using the cap certified for use with this fireplace system.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

45

46

7/12 • AA Rev • 041-401350-EXCLAIM• Glo & Heat

41 5/8 in.

 

(1057 mm)

20 3/4 in.

 

(527 mm)

29 1/2 in.

11 5/8 in.

(749 mm)

(295 mm)

 

60 5/8 in.

 

(1540 mm)

 

 

68 1/8 in.

70 1/2 in.

 

Outside

[1730 mm]

Outside

[1791 mm]

Air

(effective height)

Air

60 1/4 in.

 

 

 

Gas

 

33 in.

 

[1530 mm]

Gas

Knockout

 

 

54 3/8 in.

Knockout

 

[838 mm]

 

 

 

 

[1381 mm]

 

 

14 3/4 in.

 

 

 

9 7/8 in.

 

 

14 3/4 in.

9 7/8 in.

[375 mm]

 

 

[375 mm]

[251 mm]

 

8 3/4 in.

50 in.

10 1/2 in.

[251 mm]

 

10 1/2 in.

 

19 in.

[1270 mm]

19 in.

[267mm]

[222 mm]

 

[267 mm]

[483 mm]

 

 

 

 

[483 mm]

Dimensions Fireplace .A

Materials Reference 13

B. Optional Components

66 in.

(1676 mm)

20 in.

(508 mm)

1/2 in.(13 mm)

HX4 Hearth Extension

DM100 Glass Doors

See your Heat & Glo Dealer for a complete list of optional components.

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

47

B. Chimney Components

The following pictures show only those chimney components which may be safely used with this fireplace.

Catalog #

Description

CAK5A

Chimney Air Kit

ID4

Insulated Duct/Outside Air

UD4

Uninsulated Duct/Outside Air

SL1106

Chimney Section - 6 in. (152 mm) long

SL1112

Chimney Section - 12 in. (305 mm) long

SL1118

Chimney Section - 18 in. (457 mm) long

SL1136

Chimney Section - 36 in. (914 mm) long

SL1148

Chimney Section - 48 in. (1219 mm) long

SL11

Chimney Stabilizer

SL1130

Chimney Offset/Return - 30 deg

FS538

Ceiling Firestop - Straight

FS540

Ceiling Firestop - 30 deg

AS10

SL1100 Straight Attic Insulation Shield, 24 in. (610 mm)

JB577

Chimney Joint Band

CB576

Chimney Bracket

RF570

Roof Flashing - Flat to 6/12 Pitch

RF571

Roof Flashing - 6/12 to 12/12 Pitch

TR11

Round Termination Cap

TR11T

Round Telescoping Termination Cap

TCT1175

Terra Cotta Termination Cap

ST1175

Square Termination Cap

DTO134

Short Octagon Decorative Cap

DTO146

Tall Octagon Decorative Cap

DTS134

Short Square Decorative Cap

DTS146

Tall Square Decorative Cap

CT56

Chase Top

LDS33

Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)

LDS46

Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)

LDS-BV

Decorative Shroud - 26 in. x 26 in. (660 mm x 660 mm)

 

Field Constructed Shrouds (See “Woodburning

 

Termination Cap”)

CT-11A

Adapter-Maybe used with the following Copper Caps

 

CT-Series

 

 

 

DT-Series

 

 

14 in.

14 in. (356 mm)

(356 mm)

5-1/4in.

 

(133 mm)

4 in. (102 mm)

13 in.

(330 mm)

CAK5A Chimney Air Kit

ID4 Insulated Duct

4 in. (102 mm)

42 in.

(1067 mm)

UD4 Uninsulated Duct

4 in. (102 mm)

42 in.

(1067 mm)

A

11 in.

13 in.

(330 mm)

(279 mm)

 

 

B

 

Chimney Sections

 

A

 

 

B

Catalog #

in

 

mm

in

 

mm

SL1106

6

 

152

4-3/4

 

121

SL1112

12

 

305

10-3/4

 

273

 

 

 

 

 

 

 

SL1118

18

 

457

16-3/4

 

425

SL1136

36

 

914

34-3/4

 

883

 

 

 

 

 

 

 

SL1148

48

 

1219

46-3/4

 

1187

 

 

 

 

 

 

 

A = Actual Length

B = Effective Length (length of

chimney part after it has

been snapped to another)

 

Inside

20-3/4in.

Diameter

(527 mm)

11 in.

 

(279 mm)

 

Outside Diameter

 

13 in.

 

(330 mm)

SL11 Vent Stabilizer

48

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

 

 

Inside

 

 

Diameter

 

 

11 in.

 

 

(279 mm)

21 in.

 

Outside

(533 mm)

Diameter

 

 

 

 

13 in.

 

 

(330 mm)

 

SL1130 Offset/Return

Assembled

Diameter: 17 in./432 mm

Height: 24 in./610 mm

AS10 Straight Attic Insulation Shield

13 in.

2 in.

(330 mm)

(51 mm)

A

B17 in. (432 mm)

Catalog #

A

 

B

FS538

0-deg.

17 in.

 

432 mm

FS540

30-deg.

26 in.

 

660 mm

15-1/4in.

(387 mm)

29 in.

25-1/4in.

(737 mm)

(641 mm)

RF570 Roof Flashing

15-1/4in.

(387 mm)

JB577 Chimney Joint Band

39-7/8in.

28 in.

(711 mm)

(1013 mm)

 

RF571 Roof Flashing

15-3/4in.

13 in.(400 mm)

(330 mm)

CB576 Chimney Joint Band

 

 

 

TR11/TR444 - Round Termination Cap

10 3/4 in.

26 in.

TR-TVK

TR Top Vent Kit

CT-11A

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

49

32-3/8in.

(822 mm)

34-3/8in.

(873 mm)

TR11T/TR442 - Round Telescoping Termination Cap

23 in.(584 mm)

19 in.

(483 mm)

15-5/8in.

(397 mm)

ST1175/ST475 - Square Termination Cap

C

 

D

B

 

 

A

 

LDS33/LDS46 Decorative Shroud

 

A

 

B

C

 

 

D

Catalog #

in.

mm

in.

mm

in.

mm

in.

mm

LDS33

36

914

36

914

8.5

216

11

279

LDS46

48

1219

72

1829

8.5

216

11

279

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

A

 

 

 

LDS-BVDecorative Shroud

 

 

Catalog #

 

A

 

B

C

E

 

E

LDS-BV

in.

26

 

12.5

15.5

22

 

23

mm

660

 

318

394

533

584

 

 

20 in.(508 mm)

17 in.

 

(432 mm)

9-3/8in.

 

 

(238 mm)

B

B

A

A

10-1/4in.

(260 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

C

 

 

 

TCT1175 - Terra Cotta Cap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

72 in.

 

36 in.

 

DTS134/DTS146

 

 

DTO134/DTO146 Decorative Caps

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(1829 mm)

 

(914 mm)

 

DTO134

 

 

A

 

 

B

C

 

13-3/8in.

 

 

 

 

 

 

 

 

 

in

 

34

 

20

24

 

(340 mm)

 

 

 

 

 

 

 

 

 

 

 

mm

 

864

 

508

610

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DTO146

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in

 

46

 

22.7

26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

 

1168

 

576

660

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DTS134

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in

 

34

 

21.18

24

 

 

 

 

 

 

 

 

 

2 in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

 

864

 

538

610

 

 

 

 

 

 

 

 

(51 mm)

 

 

 

 

 

 

 

CT56 Chase Top

 

 

 

DTS146

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in

 

46

 

21.18

26

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mm

 

1168

 

538

660

50

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12

7/12 • AA Rev • 041-401350-EXCLAIM• Glo & Heat

 

Service Parts

EXCLAIM-50H,EXCLAIM-50T

 

50 in. Woodburning Fireplace

Beginning Manufacturing Date: March 2004

 

 

Ending Manufacturing Date: Active

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

1

 

 

6

5

 

 

 

 

 

7

 

 

 

 

 

 

9

8

 

 

3

2

 

 

 

 

 

 

 

10

 

 

 

 

 

 

11

 

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

 

at Depot

ITEM

DESCRIPTION

 

COMMENTS

PART NUMBER

 

1

Starter Section Assembly

 

 

 

22072B

y

2

Damper Blade Assembly

 

 

 

35160

 

3

Damper Control

 

 

 

35159

 

 

Damper Weight

 

 

 

19785A

 

4

Rear Top Standoff

 

Qty. 4 req.

 

11864i

 

5

Front Top Standoff

 

Qty. 2 req.

 

34567

 

6

Upper Front

 

 

 

4013-208

 

7

Top Front Face

 

Overlay Only

34544

 

8

Grate

 

 

 

GR39

y

9

Smoke Shelf

 

 

 

4013-185

 

10

Smoke Shield

 

 

 

4013-184

y

11

Firescreen Assembly w/Rod

 

Qty. 2 req.

 

35211

y

 

Firescreen Rod

 

1 ea.

 

34571

 

 

Firescreen Assembly

 

1 ea.

 

34590

y

 

Firescreen Handle

 

1 ea.

 

10002

 

 

Heat Shield

 

 

 

34568

 

 

Nailing Flange

 

Qty. 6 req.

 

31190

 

 

Outside Air Kit

 

Qty. 2 req.

 

35191

 

 

Fastener Pack

 

1 ea.

 

4025-023

 

 

Outside Air Shield

 

1 ea.

 

33271

y

 

4 in. Outside Air Inlet Ring

 

1 ea.

 

35192

 

 

Screen Cover (top only)

 

Qty. 2 req.

 

34548

 

 

Smoke Shield Kit

 

 

 

4013-188

y

 

Strip Protector

 

Qty. 3 req.

 

18320

 

 

Touch-UpPaint

 

 

 

71479

 

Additional service parts on following page.

07/12

Service Parts

EXCLAIM-50H,EXCLAIM-50T

 

Beginning Manufacturing Date: March 2004

 

Ending Manufacturing Date: Active

Traditional Herringbone

 

 

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

 

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Herringbone Refractory (EXCLAIM-50H)

 

 

 

 

 

Brick Refractory - Back

 

4013-068

 

 

 

Brick Refractory - Hearth

 

4013-063

 

 

 

Brick Refractory - Left Side

 

4013-070

 

 

 

Brick Refractory - Right Side

 

4013-069

 

 

Traditional Refractory (EXCLAIM-50T)

 

 

 

 

 

Brick Refractory - Back

 

4013-064

 

 

 

Brick Refractory - Hearth

 

4013-063

 

 

 

Brick Refractory - Left Side

 

4013-066

 

 

 

Brick Refractory - Right Side

 

4013-065

 

 

 

Refractory Retainer Kit

 

4013-089

 

 

 

Refractory Retainer

3 ea.

11847

 

 

 

Grate Retainer

2 ea.

4017-060

 

 

 

Installation Instructions & Owner’s Manual

 

4013-041

 

 

 

 

 

07/12

Parts Service .D

51

E. Contact Information

Please contact your Heat & Glo dealer with any questions or concerns.

For the number of your nearest Heat & Glo dealer, please visit www.heatnglo.com.

– NOTES –

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating •

Read, understand

• Leave this manual with

and maintenance

and follow these

party responsible for

instructions included.

instructions for safe

use and operation.

 

installation and

 

 

operation.

 

DO DISCARDNOT

52

Heat & Glo • EXCLAIM-504013-041• Rev AA • 7/12