Heat & Glo LifeStyle Escape-42DVLP User Manual

Size:
3.76 Mb
Download

Para obtener un ejemplar en Español de este Manual del propietario, visite www.heatnglo.com.

Pour demander un exemplaire en français de ce Manuel du propriétaire, visitez www.heatnglo.com.

Owner’s Manual

Installation and Operation

Model:

Escape-42DV

Escape-42DVLP

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual

and maintenance

these instructions for safe

party responsible for

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch.DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fi re department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as

replace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or otherflammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fi tter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

1

NAATTURAL GAS

Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gasfireplace, an elegant and clean alternative to wood burning fi replaces. The Heat & Glo gasfireplace you have selected is designed to provide the utmost in safety, reliability, and effi ciency.

As the owner of a new fi replace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas fi replace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fi replace products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your fireplace.

Model Name:___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on fi replace:_____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific fi replace can be found on the rating plate usually located in the control area of the fi replace.

Type of Gas

Gas and Electric

Information

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

Not for use with solid fuel.

((Ne doit pas entre utiliseavec un combustiblesolide).

Type of Gas (Sorte De Gaz):: This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1intheUSAorCAN/CGA B149installation codes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX·UL307B

Minimum Permissible Gas Supply forPurposes of Input Adjustment.

 

 

 

Approved Minimum (De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

MinimumManifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

TotalElectrical Requirements: 000Vac, 00Hz., less than 00Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INCANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX.INPUTBTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICESIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

Safety Alert Key:

DANGER! Indicates a hazardous situation which, if not avoidedwill result in death or serious injury.

WARNING! Indicates a hazardous situation which, if not avoidedcould result in death or serious injury.

CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 B. Glass Specifi cations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 C. BTU Specifi cations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 7 E. Non-CombustibleMaterials Specifi cation. . . . . . . . . . . . . . 7 F. Combustible Materials Specifi cation . . . . . . . . . . . . . . . . . 7 G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 H. Requirements for the Commonwealth of Massachusetts. . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 C. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10 E. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 F. Wall Controls and Wall Switches . . . . . . . . . . . . . . . . . . . 10 G. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10 H. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11 I. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 J. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .13B. MaintenanceTasks-Qualified Service Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 17

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 18

B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . 19

C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 20

E. Hearth Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . .

22

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

D. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .

29

 

B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . .

29

 

C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . .

30

 

D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . .

31

E. Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . .

31

9 Appliance Preparation

A. Removing Non-combustibleFacing Material Assembly. . 32

B. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 32

C. Installing Non-combustibleFacing Material . . . . . . . . . . . 33

10 Installing Vent Pipe

A. Assemble Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . . 34 B. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 35 C. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 35 D. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 36 E. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 37 F. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 37 G. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 38 H. Heat Shield Requirements for Horizontal Termination . . . 38 I. Install Horizontal Termination Cap . . . . . . . . . . . . . . . . . . 39

11 Gas Information

A. Fuel Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . 40

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

B. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 41

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 41

D. Electrical Service and Repair. . . . . . . . . . . . . . . . . . . . . . 43

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 43

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

3

13 Finishing

A. Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

B. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 45

C. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

D. Finishing Materials Requirements . . . . . . . . . . . . . . . . . . 46

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 47

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 47

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

E. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

F. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 48

G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

H. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

15 Troubleshooting

A. IntelliFire Ignition System. . . . . . . . . . . . . . . . . . . . . . . . . 53

16 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 55

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 56

C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

= Contains updated information.

4

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

B. Limited Lifetime Warranty

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

 

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

Parts

Labor

Gas

Wood

Pellet

EPA

Coal

Electric

Venting

Components Covered

 

 

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

 

 

1 Year

X

X

X

X

X

X

X

covered by Conditions,

 

 

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

 

 

2 years

 

 

 

 

and glass

 

 

 

 

 

 

 

 

 

 

 

X

X

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

X

X

 

 

 

Manifold tubes,

 

 

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

Burners, logs and refractory

 

 

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

X

X

X

 

 

Firebox and heat exchanger

 

 

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

X

X

All replacement parts

 

 

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

4021-645C12-29-10

 

 

 

 

 

 

 

Page 1 of 2

 

 

 

 

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

5

B. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

7KLV ZDUUDQW\ RQO\ FRYHUV ++7 DSSOLDQFHV WKDW DUH SXUFKDVHG WKURXJK DQ ++7 DXWKRUL]HG GHDOHU RU GLVWULEXWRU $ OLVW RI ++7 DXWKRUL]HG GHDOHUV LV DYDLODEOH RQ WKH ++7 EUDQGHG ZHEVLWHV

7KLV ZDUUDQW\ LV RQO\ YDOLG ZKLOH WKH ++7 DSSOLDQFH UHPDLQV DW WKH VLWH RI RULJLQDO LQVWDOODWLRQ

&RQWDFW \RXU LQVWDOOLQJ GHDOHU IRU ZDUUDQW\ VHUYLFH ,I WKH LQVWDOOLQJ GHDOHU LV XQDEOH WR SURYLGH QHFHVVDU\ SDUWV FRQWDFW WKH QHDUHVW ++7 DXWKRUL]HG GHDOHU RU VXSSOLHU $GGLWLRQDO VHUYLFH IHHV PD\ DSSO\ LI \RX DUH VHHNLQJ ZDUUDQW\ VHUYLFH IURP D GHDOHU RWKHU WKDQ WKH GHDOHU IURP ZKRP \RX RULJLQDOO\ SXUFKDVHG WKH SURGXFW

&KHFN ZLWK \RXU GHDOHU LQ DGYDQFH IRU DQ\ FRVWV WR \RX ZKHQ DUUDQJLQJ D ZDUUDQW\ FDOO 7UDYHO DQG VKLSSLQJ FKDUJHV IRU SDUWV DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

WARRANTY EXCLUSIONS:

7KLV ZDUUDQW\ GRHV QRW FRYHU WKH IROORZLQJ

&KDQJHV LQ VXUIDFH ILQLVKHV DV D UHVXOW RI QRUPDO XVH $V D KHDWLQJ DSSOLDQFH VRPH FKDQJHV LQ FRORU RI LQWHULRU DQG H[WHULRU VXUIDFH ILQLVKHV PD\ RFFXU 7KLV LV QRW D IODZ DQG LV QRW FRYHUHG XQGHU ZDUUDQW\

'DPDJH WR SULQWHG SODWHG RU HQDPHOHG VXUIDFHV FDXVHG E\ ILQJHUSULQWV DFFLGHQWV PLVXVH VFUDWFKHV PHOWHG LWHPV RU RWKHU H[WHUQDO VRXUFHV DQG UHVLGXHV OHIW RQ WKH SODWHG VXUIDFHV IURP WKH XVH RI DEUDVLYH FOHDQHUV RU SROLVKHV

5HSDLU RU UHSODFHPHQW RI SDUWV WKDW DUH VXEMHFW WR QRUPDO ZHDU DQG WHDU GXULQJ WKH ZDUUDQW\ SHULRG 7KHVH SDUWV LQFOXGH SDLQW ZRRG SHOOHW DQG FRDO JDVNHWV ILUHEULFNV JUDWHV IODPH JXLGHV OLJKW EXOEV EDWWHULHV DQG WKH GLVFRORUDWLRQ RI JODVV

0LQRU H[SDQVLRQ FRQWUDFWLRQ RU PRYHPHQW RI FHUWDLQ SDUWV FDXVLQJ QRLVH 7KHVH FRQGLWLRQV DUH QRUPDO DQG FRPSODLQWV UHODWHG WR WKLV QRLVH DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

'DPDJHV UHVXOWLQJ IURP IDLOXUH WR LQVWDOO RSHUDWH RU PDLQWDLQ WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK WKH LQVWDOODWLRQ

 

LQVWUXFWLRQV RSHUDWLQJ LQVWUXFWLRQV DQG OLVWLQJ DJHQW LGHQWLILFDWLRQ ODEHO IXUQLVKHG ZLWK WKH DSSOLDQFH IDLOXUH WR

 

LQVWDOO WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK ORFDO EXLOGLQJ FRGHV VKLSSLQJ RU LPSURSHU KDQGOLQJ LPSURSHU RSHUD-

 

WLRQ DEXVH PLVXVH FRQWLQXHG RSHUDWLRQ ZLWK GDPDJHG FRUURGHG RU IDLOHG FRPSRQHQWV DFFLGHQW RU LPSURSHUO\

 

LQFRUUHFWO\ SHUIRUPHG UHSDLUV HQYLURQPHQWDO FRQGLWLRQV LQDGHTXDWH YHQWLODWLRQ QHJDWLYH SUHVVXUH RU GUDIWLQJ

 

FDXVHG E\ WLJKWO\ VHDOHG FRQVWUXFWLRQV LQVXIILFLHQW PDNH XS DLU VXSSO\ RU KDQGOLQJ GHYLFHV VXFK DV H[KDXVW IDQV RU

 

IRUFHG DLU IXUQDFHV RU RWKHU VXFK FDXVHV XVH RI IXHOV RWKHU WKDQ WKRVH VSHFLILHG LQ WKH RSHUDWLQJ LQVWUXFWLRQV

 

LQVWDOODWLRQ RU XVH RI FRPSRQHQWV QRW VXSSOLHG ZLWK WKH DSSOLDQFH RU DQ\ RWKHU FRPSRQHQWV QRW H[SUHVVO\ DXWKRUL]HG

 

DQG DSSURYHG E\ ++7 PRGLILFDWLRQ RI WKH DSSOLDQFH QRW H[SUHVVO\ DXWKRUL]HG DQG DSSURYHG E\ ++7 LQ ZULWLQJ

 

DQG RU LQWHUUXSWLRQV RU IOXFWXDWLRQV RI HOHFWULFDO SRZHU VXSSO\ WR WKH DSSOLDQFH

 

1RQ ++7 YHQWLQJ FRPSRQHQWV KHDUWK FRPSRQHQWV RU RWKHU DFFHVVRULHV XVHG LQ FRQMXQFWLRQ ZLWK WKH DSSOLDQFH

 

$Q\ SDUW RI D SUH H[LVWLQJ ILUHSODFH V\VWHP LQ ZKLFK DQ LQVHUW RU D GHFRUDWLYH JDV DSSOLDQFH LV LQVWDOOHG

++7¶V REOLJDWLRQ XQGHU WKLV ZDUUDQW\ GRHV QRW H[WHQG WR WKH DSSOLDQFH¶V FDSDELOLW\ WR KHDW WKH GHVLUHG VSDFH ,QIRUPDWLRQ LV SURYLGHG WR DVVLVW WKH FRQVXPHU DQG WKH GHDOHU LQ VHOHFWLQJ WKH SURSHU DSSOLDQFH IRU WKH DSSOLFDWLRQ &RQVLGHUDWLRQ PXVW EH JLYHQ WR DSSOLDQFH ORFDWLRQ DQG FRQILJXUDWLRQ HQYLURQPHQWDO FRQGLWLRQV LQVXODWLRQ DQG DLU WLJKWQHVV RI

WKH VWUXFWXUH

This warranty is void if:

7KH DSSOLDQFH KDV EHHQ RYHU ILUHG RU RSHUDWHG LQ DWPRVSKHUHV FRQWDPLQDWHG E\ FKORULQH IOXRULQH RU RWKHU GDPDJLQJ FKHPLFDOV 2YHU ILULQJ FDQ EH LGHQWLILHG E\ EXW QRW OLPLWHG WR ZDUSHG SODWHV RU WXEHV UXVW FRORUHG FDVW LURQ EXEEOLQJ FUDFNLQJ DQG GLVFRORUDWLRQ RI VWHHO RU HQDPHO ILQLVKHV

7KH DSSOLDQFH LV VXEMHFWHG WR SURORQJHG SHULRGV RI GDPSQHVV RU FRQGHQVDWLRQ

7KHUH LV DQ\ GDPDJH WR WKH DSSOLDQFH RU RWKHU FRPSRQHQWV GXH WR ZDWHU RU ZHDWKHU GDPDJH ZKLFK LV WKH UHVXOW RI EXW QRW OLPLWHG WR LPSURSHU FKLPQH\ RU YHQWLQJ LQVWDOODWLRQ

LIMITATIONS OF LIABILITY:

7KH RZQHU¶V H[FOXVLYH UHPHG\ DQG ++7¶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

4021-645C12-29-10

Page 2 of 2

6

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

1 Listing and Code Approvals

A. Appliance Certifi cation

MODEL: ESCAPE-42DV

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance Heater

STANDARD: ANSIZ21.88-2002CSA2.33-M2002• UL307B

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSIZ223.1-latestedition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Glass Specifi cations

This appliance is equipped with 5 mm ceramic glass. Replace glass only with 5 mm ceramic glass. Please contact your dealer for replacement glass.

C. BTU Specifi cations

Models

 

Maximum

Minimum

Orifice

 

Input

Input

Size

(U.S. or Canada)

BTU/h

BTU/h

(DMS)

 

 

US

52,000

35,000

26

Escape-42DV(NG)

 

(0-2000FT)

 

 

 

 

 

CANADA

46,800

31,500

27

 

 

 

 

(2000-4500FT)

 

 

 

 

 

 

 

 

US

50,000

33,000

45

Escape-42DV(LP)

 

(0-2000FT)

 

 

 

 

 

CANADA

45,000

29,700

46

 

 

 

 

(2000-4500FT)

 

 

 

 

 

 

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper orifi ce size.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

F. Combustible Materials Specifi cation

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

7

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

H.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above fi nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfi ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fi tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the fl oor level where the gas equipment is to be installed. In addition, the installing plumber or gas fi tter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualifi ed licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent fl oor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certifi ed.

Signage

A metal or plastic identifi cation plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) in. in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the fl ue gases, but identifi es “special venting systems”, the following requirements shall be satisfi ed by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

8

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

2 Operating InstructionsUser Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as

replace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

- Adjustable safety gate.

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

Never leave children alone near a hot fi replace, whether operating or cooling down.

Teach children to NEVER touch the fi replace.

Consider not using the fi replace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/safety-information.

To prevent unintended operation when not using your fi replace for an extended period of time (summer months, vacations, trips, etc):

Remove batteries from remote controls.

Turn off wall controls.

Unplug 3 volt adapter plug and remove batteries on IPI models.

B. Your Fireplace

If you expect that small children or vulnerable adults may come into contact with this fi replace, the following precautions are recommended:

Install a physical barrier such as: - A decorative fi rescreen.

WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire or injury.

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

FIXED GLASS ASSEMBLY

(NOT SHOWN)

SECTION 14.G.

GRATE

SECTION 2.B.

MANTEL

HEARTH

CLEAR SPACE

SECTION 2.D.

Figure 2.1 General Operating Parts

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

9

C. Clear Space

WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2.

Avoid placing candles and other heat-sensitiveobjects on mantel or hearth. Heat may damage these objects.

 

3

FT.

CLEAR

 

 

 

 

IN

 

 

 

FRONTOFSPACE

 

 

 

FIREPLACE

Figure 2.2

Clear Space

 

D. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

E. Fixed Glass Assembly

See Section 14.G.

F. Wall Controls and Wall Switches

Follow the instructions supplied with the control installed to operate your fi replace:

For safety:

Install a switch lock or a wall/remote control with child protection lockout feature.

See your dealer if you have questions.

G. Before Lighting Fireplace

Before operating this fi replace for the fi rst time, have a qualifi ed service technician:

Verify all shipping materials have been removed from inside and/or underneath the fi rebox.

Review proper placement of logs, ember material and/or other decorative materials.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

Ensure that the fl ow of combustion air is not obstructed (termination cap).

WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.

10

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

H. Lighting Instructions (IPI)

The IPI system may be operated with two D-cellbatteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, afire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING,smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fi re department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualifi ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certifi ed for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualifi ed installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fi replace, please refer to www.fi replaces.com.

LIGHTING

INSTRUCTIONS (IPI)

1.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

3.To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4.If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2.Service technician should turn off electric power to the control when performing service.

593-913G

Final inspection by

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

11

I. After Fireplace is Lit

Initial Break-inProcedure

The fireplace should be run three to four hours continuously on high.

Turn the fi replace off and allow it to completely cool.

Remove fi xed glass assembly. See Section 14.G.

Clean fixed glass assembly. See Section 3.

Replace the fi xed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the fi replace.

NOTICE! Open windows for air circulation during fireplace break-in.

Some people may be sensitive to smoke and odors.

Smoke detectors may activate.

J.Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

condensation will disappear.

 

Blue fl ames

This is a result of normal operation and the fl ames will begin to yellow as the appliance is al-

lowed to burn for 20 to 40 minutes.

 

 

Whenfirst operated, this appliance may release an odor for thefirst several hours. This is caused

Odor from appliance

by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may

 

also be released from finishing materials and adhesives used around the appliance.

 

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

Film on the glass

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fi replace glass cleaner may be necessary. See

 

your dealer.

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the appliance.

Is it normal to see the pilot fl ame burn

In an intermittent pilot ignition system (IPI), the pilot fl ame should turn off when appliance is

turned off. Some optional control systems available with IPI models may allow pilot flame to

continually?

remain lit.

 

 

 

12

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fi replace.

When properly maintained, your fi replace will give you many years of trouble-freeservice. We recommend annual service by a qualifi ed service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualifi ed service technician only. The fi replace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fi replace must be kept clean.

CAUTION!RiskofBurns! The fireplace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fi xed glass assembly with care.

Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

DO NOT clean glass while it is hot

Prepare a work area large enough to accommodatefixed glass assembly and door frame by placing a drop cloth on a fl at, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or fl oor surfaces.

Remove door or decorative front from fi replace and set aside on work surface.

See Section 14.G for instructions to remove fi xed glass assembly.

Clean glass with a non-abrasivecommercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

Carefully set fi xed glass assembly in place on fi replace. Hold glass in place with one hand and secure glass latches with the other hand.

Reinstall door or decorative front.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

Assess condition of screen and replace as necessary.

Inspect for scratches, dents or other damage and repair as necessary.

Check that louvers are not blocked.

Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote control instructions.

Locate remote control transmitter and receiver.

Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

Place batteries as needed in remote transmitters and battery-poweredreceivers.

Place remote control out of reach of children.

If not using your fi replace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

Remove batteries from remote controls.

Unplug 3 volt adapter plug on IPI models.

Light Bulbs

Frequency: As needed

By: Homeowner

Tools needed: Protective gloves, replacement light bulbs.

Locate light bulb sockets in fi rebox. Remove existing light bulbs and proceed with instructions in Section 14.F of this manual.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

13

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

Inspect for corrosion or separation.

Verify weather stripping, sealing and fl ashing remains intact.

Inspect draft shield to verify it is not damaged or missing.

B.Maintenance Tasks-Qualified Service Technician

The following tasks must be performed by a qualifi ed service technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Qualifi ed Service Technician

Tools needed: Protective gloves, drop cloth and a stable work surface.

Inspect gasket seal and its condition.

Inspect fixed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

Confirm there is no damage to glass or glass frame. Replace as necessary.

Verify that fi xed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Logs

Frequency: Annually

By: Qualifi ed Service Technician

Tools needed: Protective gloves.

Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.

Verify correct log placement and no fl ame impingement causing sooting. Correct as necessary.

Firebox

Frequency: Annually

By: Service Technician

Tools needed: Protective gloves, sandpaper, steel wool, cloths, mineral spirits, primer andtouch-uppaint.

Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

Replace appliance if fi rebox has been perforated.

Surface cracking or crazing of fi rebrick material is normal and expected. The following types of cracks are acceptable and do not require replacement of the unit or the fi rebox:

Cracks that do not propagate entirely through the material.

Light fracture lines or “spider-webbing”on the surface of the material.

Cracks that are less than 1/32 in. wide and less than 3 in. long.

If cosmetically unacceptable, such cracks may be repaired with the SRV-PACKservice kit.

Cracks that are unacceptable:

Cracks greater than 1/32 in. wide and 3 in. long are at risk of growing.

Cracks that penetrate entirely through the firebrick material.

Inspection for cracking should be run when the appliance is cool. Cracks tend to close as the appliance heats up.

Control Compartment and Firebox Top

Frequency: Annually

By: Qualifi ed Service Technician

Tools needed: Protective gloves, vacuum cleaner, dust cloths

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

Remove all foreign objects.

Verify unobstructed air circulation.

14

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

Burner Ignition and Operation

Frequency: Annually

By: Qualifi ed Service Technician

Tools needed: Protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer.

Verify burner is properly secured and aligned with pilot or igniter.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

Replace Glowing embers with new dime-sizepieces.DO NOT block ports or obstruct lighting paths. Refer to Section 14 for proper ember placement.

Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or leaking.

Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

Inspect for lifting or other fl ame problems.

Verify air shutter setting is correct. See Section 14 for required air shutter setting. Verify air shutter is clear of dust and debris.

Inspect orifi ce for soot, dirt and corrosion. Verify orifi ce size is correct. See Service Parts List for proper orifi ce sizing.

Verify manifold and inlet pressures. Adjust regulator as required.

Inspect pilot fl ame pattern and strength. See Figure 3.1 for proper pilot fl ame pattern. Clean or replace orifi ce spud as necessary.

Inspect IPI fl ame sensing rod for soot, corrosion and

deterioration. Polish with fi ne steel wool or replace as required.

Verify that there is not a short in fl ame sensing circuit by checking continuity between pilot hood and fl ame sense rod. Replace pilot as necessary.

Figure 3.1 IPI Pilot Flame Patterns

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

15

4 Getting Started

Installer Guide

 

A. Typical Appliance System

NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

VERTICAL TERMINATION CAP (SECTION 10.G)

NON-COMBUSTIBLEROOF FLASHING MAINTAINS MINIMUM CLEARANCE

AROUND PIPE (SECTION 10.E)

STORM COLLAR (SECTION 10.F )

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.C )

FRAMING/HEADER (SECTION 5.C .)

GAS LINE (SECTION 11)

Figure 4.1 Typical System

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 8.D)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.C )

OPTIONAL

WALL SWITCH

MANTEL AND MANTEL LEG (SECTIONS 5.D and 13.B)

SURROUND

HEARTH EXTENSION

16

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fi re offi cials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the appliance is to be installed.

The vent system confi guration to be used.

Gas supply piping requirements.

Electrical wiring requirements.

Framing and fi nishing details.

Whether optional accessories—devicessuch as a wallswitch—aredesired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualifi ed service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

Flat blade screwdriver

Hammer

Phillips screwdriver

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Non-corrosiveleak check solution

1/2 - 3/4 in. length, #6 or #8 Self-drillingscrews

Caulking material (300ºF minimum continuous exposure rating)

D. Inspect Appliance and Components

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

If packaged separately, the log set and appliance grate must be installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefi t.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modifi cation of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fi re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock!

DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

17

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

B

A

PERPENDICULAR SIDEWALL

CAN OVERLAP TO 4 INCHES

FROM OPENING ON BOTH SIDES

C

D

E

 

 

 

 

A

B

C

D

E

 

 

 

 

Inches

57-1/2

22

91-1/2

64-3/4

45-3/4

 

 

 

 

Millimeters

1461

559

2325

1644

1162

 

 

 

 

 

 

 

 

 

 

 

 

Figure 5.1

Appliance Locations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

B. Constructing the Appliance Chase

A chase is a vertical box-likestructure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling firestops and wall shield firestops and construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever fl oor of the chase should be insulated. Vapor and air infi ltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infi ltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with caulk with a minimum of

300ºF continuous exposure rating to seal gaps. Gas line holes and other openings should be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with unfaced insulation. If the appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth.DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specified air space clearances to appliance and vent pipe:

Insulation and other materials must be secured to prevent accidental contact.

The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fi replace or chimney.

Failure to maintain airspace may cause overheating and a fi re.

A

FROM APPLIANCE

 

 

OPENING TO CEILING

E

B

 

C

J

F

H

 

D

 

G

I

* MINIMUM FRAMING DIMENSIONS

 

A

B

C

D

E

F

G

H

I

J

 

Rough

Rough

Rough

Rough

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

Opening

Opening

Opening

Opening

 

(Vent Pipe)

(Height)

(Depth)

(Width)

to Ceiling

Floor

Flooring

Appliance

Appliance

Appliance

 

 

 

 

 

 

 

Inches

10

52-1/2

22

57-1/2

43

0

12

1/2

1/2

36

 

 

 

 

 

 

 

 

 

 

 

mm

254

1334

559

1461

1092

0

305

13

13

914

 

 

 

 

 

 

 

 

 

 

 

* Adjust framing dimensions for interior sheathing (such as sheetrock)

Figure 5.2 Clearances to Combustibles

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

19

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantels

 

 

 

 

 

 

 

3-1/2IN.

 

 

 

 

 

 

 

 

FINISH WALL

 

 

 

 

 

 

 

 

COMBUSTIBLE

 

 

 

 

 

 

 

 

NO COMBUSTIBLES

 

 

 

 

 

 

 

IN THIS AREA

 

 

 

 

 

 

 

 

COMBUSTIBLE

39 IN.

 

 

 

 

 

 

FRAMING

 

 

 

 

 

 

 

 

METAL PANELS

 

 

 

 

 

 

 

(PROVIDED)

 

 

 

 

 

 

 

 

COMBUSTIBLE

 

 

 

 

 

 

 

PROJECTIONS

 

 

 

 

 

 

 

 

12 IN.

 

 

 

 

 

 

 

 

 

10-1/2IN.

 

 

 

 

 

11-12IN.

 

 

9 IN.

 

 

 

 

 

 

7-1/2IN.

 

 

 

 

 

 

 

 

6 IN.

 

 

 

 

 

 

 

 

4-3/4IN.

 

12 IN.

 

 

 

 

 

 

3 IN.

 

MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 IN. MIN.

 

 

 

 

 

 

 

6 IN. MIN.

 

 

NON-COMBUSTIBLE

 

 

 

 

 

 

 

FACING MATERIAL

 

 

TOP OF FIREPLACE

 

MIN. 1/2 IN. THICKNESS

 

 

 

 

 

 

 

 

 

OPENING

 

Height

 

in.

6

7

8

9

10

11

12

above

 

mm

152

178

203

228

254

279

305

opening

 

 

 

 

 

 

 

 

Horizontal

in.

3

4-3/4

6

7-1/2

9

10-1/2

12

Mantel

 

mm

76

121

152

191

228

267

305

distance

 

 

 

 

 

 

 

 

Figure 5.3

Minimum Vertical and Maximum Horizontal

 

 

Dimensions of Combustibles

 

 

 

Combustible Mantel Legs or Wall Projections

4 INCH

MINIMUM

UNLIMITED

NON-COMBUSTIBLE

MATERIAL

Figure 5.4 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

1/2 INCH

SHEETROCK

NON-COMBUSTIBLEZONE

11-1/2IN.

6 IN. (NON-COMBUSTIBLE

BOARD)

Figure 5.5 Non-CombustibleZone

20

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

E. Hearth Extension

WARNING! Risk of Fire! Hearth extension required to protect combustible floors in front of appliance.

The base of the fi replace may sit on a combustible surface. The area in front of the fi replace must be protected by a noncombustible hearth extension, unless the fi replace is raised a minimum of 3 inches above the combustible fl oor or hearth. See fi gures 5.6 and 5.7.

MARBLE, GRANITE, TILE OR

 

OTHER NON-COMBUSTIBLE

FRONT EDGE

HEARTH EXTENSION

OF ASH LIP

 

12 in.

 

1 in. Max.

 

WOOD OR OTHER COMBUSTIBLE

BOTTOM OF FIREPLACE

FLOOR OR PLATFORM

Figure 5.6 Fireplace sitting on combustible surface

FRONT EDGE

1 INCH

OF ASH LIP

(BUILT INTO UNIT)

4 INCH

 

 

3 INCH MIN.

WOOD OR OTHER

COMBUSTIBLES UP TO

BOTTOM

MAY BE

COMBUSTIBLE

1 INCH THICK ALLOWED

OF FIREPLACE

COMBUSTIBLE

FLOOR OR PLATFORM

UNDER THE OPENING

 

MATERIAL

Figure 5.7 Fireplace raised a minimum of 3 inches away from combustible surface

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

21

6 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Maintain vent clearance to combustibles as specifi ed.

DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and fi re.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12.................................................1.25*

Over 7/12 to 8/12.................................................1.5*

Over 8/12 to 9/12.................................................2.0*

Over 9/12 to 10/12...............................................2.5

Over 10/12 to 11/12.............................................3.25

Over 11/12 to 12/12.............................................4.0

Over 12/12 to 14/12.............................................5.0

Over 14/12 to 16/12.............................................6.0

Over 16/12 to 18/12.............................................7.0

Over 18/12 to 20/12.............................................7.5

Over 20/12 to 21/12.............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge

Opening

 

 

A

B

6 in. (minimum) up to 20 in.

18 in. minimum

152 mm/508 mm

457 mm

20 in. and over

0 in. minimum

Gas, Wood or Fuel Oil

Termination Cap

B

A *

Gas

Termination

Cap **

*If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

**In a staggered installation with both gas and wood or fuel oil terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Figure 6.2 Staggered Termination Caps

22

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

 

 

 

 

 

 

 

 

 

 

O

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

C

 

 

 

F

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

Q

 

J

B

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

H or i

 

 

 

 

 

 

V

 

B

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

D

X

V

 

E

 

V

 

 

 

 

G

 

 

 

 

 

 

V

 

H

 

 

 

 

 

 

 

 

V

M

 

 

V

 

 

 

 

 

 

 

V

V

H V

 

L

 

 

 

 

 

 

A

A

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

 

 

 

 

Electrical

K

V

 

V

 

 

 

 

 

 

V

 

= VENT TERMINAL

 

 

 

 

 

 

Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X = AIR SUPPLY INLET

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

 

 

 

V

 

 

A

=

12 inches.................

clearances above grade, veranda,

 

 

Covered Alcove Applications

 

 

 

 

porch, deck or balcony

(Spaces open only on one side and with an overhang)

 

B

=

12 inches

clearance to window or door that may

 

N

=

6 inches ...........

non-vinylsidewalls

 

 

 

 

be opened, or to permanently closed

 

 

12 inches

vinyl sidewalls

 

 

 

 

window

 

 

 

 

 

 

O

=

18 inches

non-vinylsoffi t and overhang

 

C

=

24 inches

clearance below unventilated soffit

 

 

 

42 inches

vinyl soffi t and overhang

 

 

 

24 inches

clearance below ventilated soffit

 

 

 

 

 

P

=

8 ft.

 

 

 

 

42 inches

clearance below vinyl soffits and

 

 

 

 

 

 

 

 

 

 

 

 

 

electrical service

 

 

 

QMIN

RMAX

 

D

=

6 inches...................

clearance to outside corner

 

1 cap

3 feet

2 x Q ACTUAL

 

E

=

6 inches...................

clearance to inside corner

 

2 caps

6 feet

1 x Q ACTUAL

 

F

=

3 ft. (Canada)

not to be installed above a gas me-

 

 

 

3 caps

9 feet

2/3 x Q ACTUAL

 

 

 

 

ter/regulator assembly within 3 feet

 

 

 

 

 

horizontally from the center-lineof the

 

4 caps

12 feet

1/2 x Q ACTUAL

 

 

 

 

regulator

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

 

G

=

3 ft

clearance to gas service regulator

 

 

 

 

 

 

 

 

 

 

vent outlet

 

 

Measure vertical clearances from this surface.

 

H

= 12 inches

clearancetonon-mechanical(unpow-

 

 

 

 

 

 

 

 

 

 

 

 

ered) air supply inlet, combustion air

 

 

 

 

 

 

i

=

3 ft. (U.S.A.)

inlet or direct-venttermination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 ft. (Canada)...........

clearance to a mechanical (powered)

 

 

 

 

 

 

 

 

 

air supply inlet

 

 

 

 

 

 

All mechanical air intakes within 10 feet of a termination cap

 

 

 

 

 

 

must be a minimum of 3 feet below termination.

 

 

 

 

 

 

J

=

7 ft..........................

Onpublic property: clearance above

 

 

 

 

 

 

 

 

 

paved sidewalk or a paved driveway.

 

 

 

 

 

 

A vent shall not terminate directly above a sidewalk or paved

 

 

 

 

 

 

driveway which is located between two single family dwellings

 

 

 

 

 

 

and serves both dwellings.

 

 

Measure horizontal clearances from this surface.

 

 

 

 

 

CAUTION! Risk of Burns! Termination caps are HOT,

 

 

 

 

 

consider proximity to doors, traffic areas or where people

 

K

=

6 inches

clearance from sides of electrical

may pass or gather (sidewalk, deck, patio, etc.). Listed cap

 

shields available. Contact your dealer.

 

 

 

 

 

service

• Local codes or regulations may require different

 

L

=

12 inches

clearance above electrical service

 

clearances.

 

 

 

Location of the vent termination must not interfere with access to the

 

 

 

• Vent system termination is NOT permitted in screened

 

electrical service.

 

 

 

 

 

 

porches.

 

 

 

M

= 18 inches ....................

clearanceunderveranda,porch,deck,

• Vent system termination is permitted in porch areas with

 

 

 

 

balcony or overhang

two or more sides open.

 

 

 

42 inches ................

vinyl or composite overhang

• Hearth & Home Technologies assumes no responsibility

 

Permitted when veranda, porch, deck or balcony is fully open

for the improper performance of the appliance when the

 

on a minimum of 2 sides beneath the fl oor.

 

venting system does not meet these requirements.

 

 

 

 

 

Figure 6.3 Minimum Clearances for Termination

• Vinyl protection kits are suggested for use with vinyl siding.

 

 

 

 

 

 

 

 

 

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

 

23

7 Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home Technologies DVP venting systems. Refer to Section 16.B for vent component information.

DO NOT mix pipe, fi ttings or joining methods from different manufacturers.

The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOTvent to a pipe serving a separate solid fuel burning appliance.

B. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

 

 

V1

First section (closest to appliance) of vertical length

 

 

V2

Second section of vertical length

 

 

H1

First section (closest to appliance) of horizontal length

 

 

H2

Subsequent sections of horizontal length

 

 

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2in. (216 mm) horizontal run and8-1/2in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1).

Vertical

 

in.

 

 

 

 

.

 

 

1/2-8

 

12

in

 

 

8-1/2in.

Horizontal

Figure 7.1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

Pipe measurements are shown using the effective length of pipe (see Figure 7.2).

Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 6.3).

Vertical terminations are measured to bottom of termination cap.

Horizontal pipe installed level with no rise.

 

Pipe

Effective Length

 

Inches

Millimeters

 

 

 

DVP4

4

102

 

DVP6

6

152

Effective

DVP12

12

305

 

 

 

Height/Length

DVP24

24

610

 

DVP36

36

914

 

DVP48

48

1219

 

DVP6A

3 to 6

76 to 152

 

DVP12A

3 to 12

76 to 305

 

DVP12MI

3 to 12

76 to 305

 

DVP24MI

3 to 24

76 to 610

Figure 7.2 DVP Pipe Effective Length

 

 

24

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

E. Vent Diagrams

Top Vent - Horizontal Termination

One Elbow

Note: A fl ue restrictor can only

 

Note: Must have a 24 inches mini-

be used in vent runs that in-

 

mum vertical vent before attaching

clude no elbows and exceed

 

any elbow to the unit.

30 ft. total of straight vertical.

 

 

 

 

 

 

V1

H1

Figure 7.3

Two Elbows

Note: A fl ue restrictor can only

 

Note: Must have a 24 inches mini-

be used in vent runs that in-

 

mum vertical vent before attaching

clude no elbows and exceed

 

any elbow to the unit.

30 ft. total of straight vertical.

 

 

 

 

 

 

V1 Minimum

H1 Maximum

2 ft..

610 mm

7 in*

178 mm

 

 

 

 

3 ft.

914 mm

2 ft.

610 mm

 

 

 

 

4 ft.

1.2 m

4 ft.

1.2 m

5 ft.

1.5 m

9 ft.

2.7 m

6 ft.

1.8 m

12 ft.

3.7 m

 

 

 

 

7 ft.

2.1 m

14 ft.

4.3 m

 

 

 

 

10 ft.

3.0 m

20 ft.

6.1 m

20 ft.

6.1 m

40 ft.

12.2 m

After V1 = 6 ft. then H1 = 2 x V ft. Maximum V1 + H1 = 60 ft. Maximum

*when used with approved termination caps

V1 Minimum

H1+ H2

3 ft.

914 mm

18 in

457 mm

4 ft.

1.2 m

3 ft.

914 mm

5 ft.

1.5 m

7 ft.

2.1 m

 

 

 

 

6 ft.

1.8 m

10 ft.

3.0 m

 

 

 

 

7 ft.

2.1 m

12 ft.

3.7 m

10 ft.

3.0 m

18 ft.

5.5 m

20 ft.

6.1 m

20 ft.

6.1 m

 

 

 

 

After V1= 6 ft. then H1 = 2 x V1 ft. Maximum V1 + H1 + H2 = 60 ft. Maximum

H1 + H2 = 20 ft. Maximum

H2

V1

H1

 

Figure 7.4

INSTALLED

 

 

HORIZONTALLY

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

25

Top Vent - Horizontal Termination - (continued)

Three Elbows

Note: Must have a 24 inches minimum vertical vent before attaching any elbow to the unit.

Note: A fl ue restrictor can only be used in vent runs that include no elbowsand exceed 30 ft. total of straight vertical.

 

V1

 

H1

V2 H

 

2

2 ft.

610 mm

7 in

178 mm

* H2 Max = 2 X V2

3 ft.

914 mm

2 ft.

610 mm

* H2 Max = 2 X V2

4 ft.

1.2 m

4 ft.

1.2 m

* H2 Max = 2 X V2

5 ft.

1.5 m

9 ft.

2.7 m

* H2 Max = 2 X V2

6 ft.

1.8 m

12 ft.

3.7 m

*

H2

Max = 2 X V2

7 ft.

2.1 m

14 ft.

4.3 m

*

H2

Max = 2 X V2

10 ft.

3.0 m

20 ft.

6.1 m

*

H2

Max = 2 X V2

V1 + H1 must be adhered to.

* V2 has no specifi c restrictions EXCEPT,

Ht max = 2 x Vt and Vtotal + Htotal cannot exceed 60 ft. Maximum

H2

V2

H1V1

Figure 7.5

26

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

Top Vent - Vertical Termination

No Elbow

Note: A fl ue restrictor can only be used in vent runs that include no elbowsand exceed 30 ft. total of straight vertical.

V1 = 50 ft. Max. (15.2 m)

V1 = 3 ft. Min. (914 mm)

FLUE

RESTRICTOR

FLUE RESTRICTOR

V1

Figure 7.6

Two Elbows

 

V1

 

H1

V2

2 ft.

610 mm

1 ft.

305 mm

*

 

Note: Must have a 24 inches mini-

3 ft.

914 mm

3 ft.

914 mm

*

4 ft.

1.2 m

4 ft.

1.2 m

*

mum vertical vent before attaching

any elbow to the unit.

5 ft.

1.5 m

9 ft.

2.7 m

*

 

6 ft.

1.8 m

12 ft.

3.7 m

*

Note: A fl ue restrictor can only

 

V1 + V2 + H1 = 50 ft. (15.2 m) Max.

 

be used in vent runs that in-

*No specifi c restrictions on this value EXCEPT

clude no elbows and exceed

V1

+ V2 + H1 cannot exceed 60 ft. (18.3 m).

 

30 ft. total of straight vertical.

 

 

V2

After V1 = 6 ft., then H1 Max.= V1 x 2

 

V1

H1

Figure 7.7

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

27

Top Vent - Vertical Termination - (continued)

Three Elbows

Note: Must have a 24 inches minimum vertical vent before attaching any elbow to the unit.

Note: A fl ue restrictor can only be used in vent runs that include no elbowsand exceed 30 ft. total of straight vertical.

 

V1

H1

H2

V2

Ht Max.

2 ft.

610 mm

*

*

**

7 in

178 mm

3 ft.

914 mm

*

*

**

2 ft.

610 mm

4 ft.

1.2 m

*

*

**

4 ft.

1.2 m

 

 

 

 

 

 

 

5 ft.

1.5 m

*

*

**

8 ft.

2.4 m

 

 

 

 

 

 

 

6 ft.

1.8 m

*

*

**

12 ft.

3.7 m

7 ft.

2.1 m

*

*

**

14 ft.

4.3 m

10 ft.

3.0 m

*

*

**

20 ft.

6.1 m

 

 

 

 

 

 

 

*H1 and H2 has no specifi c restrictions EXCEPT,

after V1 = 6 ft., then Ht Max = 2 x V1 **VT + HT = 60 ft. Max.

V2

H1

H2

V1

 

INSTALLED

HORIZONTALLY

Figure 7.8

28

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent.DO NOT pack insulation or other combustibles:

Between ceiling firestops

Between wall shield firestops

Around vent system

Failure to keep insulation or other material away from vent pipe may cause over heating and fire.

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).

DVP heat shield - designed to be used on a wall 4 in. to7-1/4in. (102 mm to 184 mm) thick.

If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4in. aDVP-HSM-Bwill be required.

3 in. (76 mm) top clearance

1 in. (25 mm) clearance around vertical sections

Heat

3 in. (76 mm)

Shield

top clearance

 

Heat

 

Shield

 

1 in. (25 mm)

Wall

clearance

Shield

bottom & sides

Firestop

 

 

WALL

Figure 8.1 Horizontal Venting Clearances To Combustible

Materials

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield fi restop(s). The wall shield fi restop maintains minimum clearances and prevents cold air infi ltration.

The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.

A wall shield fi restop is required on one side only on interior walls. If your local inspector requires a wall shield fi restop on both sides, then both wall shield fi restops must have a heat shield (refer to Section 16.B.) attached to them.

See Section 10.M. for information for regarding the installation of a horizontal termination cap.

Non-CombustibleWall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable.

Whenever a non-combustiblewall is penetrated, the wall shield fi restop is only required on one side and no heat shield is necessary.

10 in.

12 in.

B

A

A* B

73 -1/8in. 72-1/8in.

*Shows center of vent framing hole for top venting. The center of the hole is one (1) inch (25.4 mm) above the center of the horizontal vent pipe.

Figure 8.2 Exterior Wall Hole

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

29

C. Install the Ceiling Firestop

A ceiling fi restop MUST be used between fl oors and attics.

DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ floor (see Figure 8.3).

Frame the area with the same sized lumber as used in ceiling/fl oor joist.

The ceiling firestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between fl oors that are not insulated. Refer to Figure 8.4.

Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu- lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

 

 

ATTIC ABOVE

 

 

A

 

 

A

 

PIPE

A

 

DVP

10 in. (254 mm)

Figure 8.3

Installing Ceiling Firestop

 

 

INSTALL ATTIC INSULATION SHIELDS

 

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

 

3 FASTENERS

 

 

PER SIDE

 

 

CEILING FIRESTOP

CEILING FIRESTOP

 

INSTALLED BELOW CEILING

INSTALLED ABOVE CEILING

 

Figure 8.4 Installing the Attic Shield

 

30

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

 

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specifi ed clearance and be secured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling fi restop.

Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling fi restop and attach to the fi restop.

Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Vaulted Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Cut the attic insulation shield (if application is for vaulted ceiling) to fi t your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling fi restop.

Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling fi restop and attach to the fi restop.

Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90°

TO MAINTAIN CLEARANCE

AND PREVENT INSULATION

FROM FALLING INSIDE

BEND 3 TABS

OUTWARD TO

FASTEN TO CEILING

FIRESTOP-BEND

REMAINING TABS

INWARD 90 DEGREES

TO MAINTAIN

INSERT 3 CLEARANCE

SCREWS

Figure 8.5 Attic Insulation Shield

E. Installing the Optional Heat-Zone® Gas Kit

Remove the knockouts from the top of the appliance and discard them (see Figure 8.6).

Center the duct collar around the exposed hole and attach it to the appliance with 3 screws. Note: Do this BEFORE fi nal positioning of the appliance.

Determine the location for the air register/fan housing assembly.

Reference the Heat-Zone® Gas Kit instructions for the remaining installation steps.

KNOCKOUTS

Figure 8.6 Heat Zone® Knockouts

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

31

9 Appliance Preparation

A.Removing Non-combustibleFacing Material Assembly

The non-combustibleassembly is located on the back side of appliance.

CAUTION

Handle with care.

Non-combustiblematerial may be damaged if dropped.

Hold non-combustiblepieces in place.

Remove and save two screws from upper bracket.

Remove non-combustiblepieces.

Remove and save three screws from lower bracket.

Discard brackets.

Replace screws in holes where brackets were attached to appliance.

B. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

Sagging or loose insulation

Insulation backing or plastic

Framing and other combustible materials

Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs.

Nailing tabs

(Both sides)

Figure 9.1 Proper Positioning and Securing of an Appliance

Failure to maintain air space clearance may cause overheating and fire.

The diagram shows how to properly position and secure the appliance (see Figure 9.1). Nailing tabs are provided to secure the appliance to the framing members.

Bend out nailing tabs on each side.

Place the appliance into position.

Keep nailing tabs fl ush with the framing.

Level the appliance from side to side and front to back.

Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

Secure the appliance to the framing by using nails or screws through the nailing tabs.

Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

32

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

C. Installing Non-combustibleFacing Material

WARNING

Fire Risk.

Follow these instructions exactly.

Facing materials must be installed properly to prevent fi re.

• No materials may be substituted without authorization by Hearth & Home Technologies.

Center and attach two top boards to the framing members. See Figure 9.2.

Attach left and right side pieces to framing members.

Use fasteners from fastener packet (in manual bag) in shaded areas.

Use regular sheetrock screws in non-shadedareas.

Use a wet or dry towel or soft brush to remove dust or dirt from facing material.

Apply a non-combustibleadhesive to attach tile, stone or othernon-combustiblefi nishing materials per manufacturer’s instructions.

NON-COMBUSTIBLE

ZONE

43 in.

60 in.

Figure 9.3 Complete Installation of Non-combustibleFacing

Material

NON-COMBUSTIBLE

FACING MATERIAL

(9 IN. WIDE, SUPPLIED ATTACHED TO

BACK OF APPLIANCE)

 

9 IN.

NO FASTENERS

2 IN.

IN THIS AREA

1 IN.

 

APPLY FASTENERS

FROM FASTENER PACKET

IN THESE AREAS

Figure 9.2 Attaching Non-combustibleFacing Material

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

33

10 Installing Vent Pipe

A. Assemble Vent Sections

Attach Vent to the Firebox Assembly

Note: The end of the pipe sections with the lanced tabs will face toward the appliance.

Attach the fi rst pipe section to the starting collar:

Lanced pipe end to the starting collar

Inner pipe over inner collar

Push the pipe section until all lanced tabs snap in place

Lightly tug on pipe to confi rm it has locked.

Commercial, Multi-family(Multi-levelexceeding two stories), orHigh-RiseApplications

All outer pipe joints must be sealed with high temperature silicone (minimum of 300ºF continuous exposure rating), including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 10.1

Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer fl ues shall be sealed in this manner, unless otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Assemble Pipe Sections

Per Figure 10.2:

Start the inner pipe on the lanced end of section A into the fl ared end of section B.

Start the outer pipe of section A over the outer pipe of section B.

Once both vents sections are started, push fi rmly until all lanced tabs lock into place.

Lightly tug on the pipe to confi rm the tabs have locked.

It is acceptable to use screws no longer than 1/2 in. (13 mm) to hold outer pipe sections together. If predrilling holes, DO NOT penetrate inner pipe.

For 90° and 45° elbows that are changing the vent direction from horizontal to vertical, one screw minimum should be put in the outer fl ue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1/2 in. (13 mm). If predrilling screw holes, DO NOT penetrate inner pipe.

Figure 10.1 High Temperature Silicone Sealant

A

Lances

B

Figure 10.2

Figure 10.3

Note: Make sure that the seams are not aligned to prevent unintentional disconnection.

CORRECT

Figure 10.4 Seams

INCORRECT

34

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

B. Assemble Slip Sections

Slide the inner flue of the slip section into the innerflue of the pipe section and the outer flue of the slip section over the outer fl ue of the pipe section. See Figure 10.5.

Slide together to the desired length.

Pilot hole

Figure 10.5 Slip Section Pilot Holes

Maintain a 1-1/2in. (38 mm) overlap between the slip section and the pipe section.

Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 10.7.

Figure 10.6 Screws into Slip Section

Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE:If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

C. Secure the Vent Sections

Vertical runs must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise.

Horizontal sections must be supported every 5 feet (1.52 m).

Vent supports or plumbers strap (spaced 120º apart) may be used to support vent sections. See Figures 10.7 and 10.8.

Wall shield fi restops may be used to provide horizontal support to vent sections.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

120º

Figure 10.7 Securing Vertical Pipe Sections

120º

Figure 10.8 Securing Horizontal Pipe Sections

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

35

D. Disassemble Vent Sections

Rotate either section (see Figure 10.9) so the seams on both pipe sections are aligned as shown in Figure 10.10.

Pull carefully to separate the pieces of pipe.

Figure 10.9 Rotate Seams for Disassembly

Figure 10.10 Align and Disassemble Vent Sections

36

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

E. Install Metal Roof Flashing

See minimum vent heights for various pitched roofs (Figure 10.11) to determine the length of pipe to extend through the roof.

Slide the roof fl ashing over the pipe sections extending through the roof as shown in Figure 10.12.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12............................1.25*

Over 7/12 to 8/12..............................1.5*

Over 8/12 to 9/12..............................2.0*

Over 9/12 to 10/12............................. 2.5

Over 10/12 to 11/12......................... 3.25

Over 11/12 to 12/12........................... 4.0

Over 12/12 to 14/12........................... 5.0

Over 14/12 to 16/12........................... 6.0

Over 16/12 to 18/12........................... 7.0

Over 18/12 to 20/12........................... 7.5

Over 20/12 to 21/12........................... 8.0

* 3 foot minimum in snow regions

Figure 10.11 Minimum Height From Roof To Lowest Discharge

Opening

 

 

NOTICE: Failure to properly caulk the roof flashing and pipe seams may permit entry of water.

Caulk the gap between the roof fl ashing and the outside diameter of the pipe.

Caulk the perimeter of the fl ashing where it contacts the roof surface. See Figure 10.12.

Caulk the overlap seam of any exposed pipe sections that are located above the roof line.

CAULK

Figure 10.12

F. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Connect both halves of the storm collar with two screws (see Figure 10.13).

Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

Slide the assembled storm collar down the pipe section until it rests on the roof fl ashing (see Figure 10.14).

Caulk around the top of the storm collar (see Figure 10.15).

Figure 10.13 Assembling the Storm Collar

Figure 10.14 Assembling the Storm Collar Around the Pipe

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

37

G. Install Vertical Termination Cap

Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of the cap over the outer fl ue of the pipe section.

Secure the cap by driving three self-tappingscrews (supplied) through the pilot holes in the outer collar of the cap into the outer fl ue of the pipe (see Figure 10.15).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 10.15

H.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.

DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 10.16).

Heat shields must overlap 1-1/2in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attachedto the wall shield fi restop. The other section isfactory-attachedto the cap. See Figure 10.16.

If the wall thickness does not allow the required 1-1/2in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

If the wall thickness is less than 4 in. (102 mm), the heat shields on the cap and wall shield fi restop must be trimmed. A minimum 1-1/2in. (38 mm) overlap MUST be maintained.

Useanextendedheatshieldifthefi nishedwallthickness is greater than 7-1/4in. (184 mm).

The extended heat shield may need to be cut to length maintaining suffi cient length for a 1-1/2in. (38 mm) overlap between heat shields.

Attach the extended heat shield to either of the existing heatshieldsusingthescrewssuppliedwiththeextended heat shield. Refer to vent components diagrams in the back of this manual.

Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields maynot be field constructed.

38

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

I. Install Horizontal Termination Cap

WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent.

1-1/2(38 mm) minimum overlap of flue telescoping section is required.

Failure to maintain overlap may cause overheating and fire.

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at outside edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current

ANSI Z223.1 and CAN/CGA-B149installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

Note: When using termination caps withfactory-suppliedheat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

HEAT SHIELD

EXTENDED

1-1/2IN. (38 MM) MIN.

HEAT SHIELD

OVERLAP

WALL SHIELD

 

FIRESTOP

 

SLIP SECTION

 

CAN BE EXTENDED

 

INNER VENT

SHEATHING

OUTER VENT

 

INTERIOR

EXTERIOR

VENT DEPTH FROM BACK OF APPLIANCE TO

 

OUTSIDE SURFACE OF EXTERIOR WALL

 

(SEE CHART BELOW)

 

Figure 10.16 Venting through the wall

 

Termination Cap Specifi cation Chart (depth without using additional pipe sections)

 

DVP-TRAPK1

DVP-TRAP1

DVP-TRAPK2

DVP-TRAP2

 

Top Vent

Rear Vent

Top Vent

Rear Vent

 

Depth

Depth

Depth

Depth

 

3-1/2in. to

N/A

6 in. to

N/A

 

5-3/8in.

10 in.

Escape-

 

 

 

 

 

 

42DV

 

 

 

 

DVP-HPC1

DVP-HPC1

DVP-HPC2

DVP-HPC2

 

 

Top Vent

Rear Vent

Top Vent

Rear Vent

 

Depth

Depth

Depth

Depth

 

3-1/2in. to

N/A

5-3/4in. to

N/A

 

5-5/8in.

9-3/4in.

 

 

 

DVP-TRAP1can adjust1-1/2in.(3-1/8to4-5/8)

DVP-TRAP2can adjust 4 in.(5-3/8to9-3/8)

DVP-HPC1can adjust2-1/8in.(4-1/4to6-3/8)

DVP-HPC2can adjust4-1/8in.(6-3/8to10-1/2)

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

39

11 Gas Information

A. Fuel Conversion

Make sure the appliance is compatible with available gas types.

Conversions must be made by a qualified service technician using Hearth & Home Technologies specifi ed and approved parts.

B. Gas Pressure

Optimum appliance performance requires proper input pressures.

Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

Pressure requirements are:

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

14.0 in. w.c.

14.0 in. w.c.

Manifold pressure

3.5 in. w.c.

9.2 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualifi ed installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fi tter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm)T-handlemanualshut-offvalve and fl exible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

C. Gas Connection

Refer to Reference Section 16 for location of gas line access in appliance.

Gas line may be run through knockout(s) provided.

The gap between supply piping and gas access hole may be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air infiltration.

Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

Pipe incoming gas line into valve compartment.

Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.

Purge should be performed by qualified service technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all fittings and connections with a non-corrosivecommercially availableleak-checksolution.DO NOT use open flame. Fittings and connections could have loosened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce burner orifice 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce burner orifi ce 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

40

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric

Code CSA C22.1.

Wire the appliance junction box to 110-120VAC. This is required for proper operation of the appliance.

A110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

C. Optional Accessories Requirements

This appliance may be used with a wall switch or a wall mounted thermostat.

Wiring for optional Hearth & HomeTechnologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

This appliance comes standard with a multi-functionwall switch installed in the unit. A bag containing the wall switch, cover plate and fl ame control solenoid is located in the manual bag assembly on the right side of the unit.

Follow the “Determine Location” and “Wiring the Wall Switch” sections of the WSK-MLTinstructions.

Install the fl ame control solenoid by following Steps 5 - 11 in the “Installing the Control Box” section of the WSK-MLTinstructions.

Also carefully follow the “Setting Flame Height/Manifold Pressure” section of the included instructions to properly set the valve pressure. Operating instructions are also included in the WSK-MLTinstructions.

B. IntelliFire Ignition System Wiring

Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figure 12.1 IntelliFire Pilot Ignition (IPI) Wiring Diagram.

This appliance is equipped with an IntelliFire control valve which operates on a 3 volt system.

Plug the 3-voltAC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur. Batteries should not be placed in the battery pack until needed.

NOTICE: Do not use battery back up without removing refractory panels and mesh. Failure to do so may result in damage to components. Use battery back up to operate appliance only during power outage.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

41

WIRES WITH LABEL “FOR USE WITH

 

 

REMOTE OR WALL SWITCH ONLY”

DETAIL A

BATTERIES

(LOCATED UNDER FIREPLACE)

 

 

GREEN

ORANGE

 

 

 

GROUND

 

IPI

BLACK

 

VALVE

 

 

FLAME

RED (FEMALE/MALE)

RED (MALE/FEMALE)

SOLENOID

 

 

 

 

 

 

BLACK

RED

 

 

 

 

 

YELLOW (HNG)

 

 

 

 

 

BATTERY WHITE (HTL)

 

 

 

 

BLACK

RED

 

1

 

 

IPI PILOT

G Y R

IPI

2

 

 

3

 

 

BROWN

MODULE

4

BROWN

 

BROWN

 

5

BROWN

 

 

6

 

 

RED

 

7

 

 

 

8

 

3V DC

 

 

 

 

 

BLACK

 

 

 

 

RED

GREEN

REAR VIEW

R Y G

FRONT VIEW

 

FLAME ON

RED

 

 

 

RED

 

 

 

 

ORANGE

 

FLAME HIGH/LOW

AC

ORANGE

ADAPTER WIRES

 

 

 

PLUG

BLACK

 

 

 

BLACK

 

 

 

GROUND

 

 

AUX

PIGTAIL

FIREBOX LIGHTS

CONNECTION

GREEN

BLACK

*

 

 

YELLOW

FACTORY

 

YELLOW

CONNECTED

TOGETHER

 

FAN THERMOSTAT

 

FAN

 

CONNECTION

WHITE

GROUND

CONTINUOUS 110VAC SUPPLY

HOT

 

 

TRANS

REM/AUX

FAN

NEUTRAL

 

 

NOTE: BATTERY PACK AND SWITCH ARE LOCATED IN THE MANUAL BAG. THE BATTERY PACK IS TO BE USED ONLY IN THE CASE OF A POWER OUTAGE.

NOTE: APPLIANCE WILL NOT OPERATE UNLESS PROPERLY GROUNDED. *MUST ORDER PLUG-ADPSEPARATELY IF USING THEHEAT-ZONE.

NOTE: IGNITION MODULE, VALVE, PILOT

AND WALL SWITCH OPERATE ON 3 VOLTS.

DETAIL A

ON/OFF ROCKER SWITCH

GREEN

Figure 12.1 IntelliFire Pilot Ignition (IPI) Wiring Diagram

 

BATTERIES

BLACK

RED

42

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

PVK-80POWERVENT

 

 

 

 

 

 

 

 

 

(GREEN)

 

 

 

 

 

 

 

 

 

 

 

JUNCTION BOX

 

 

(WHITE)

 

 

 

 

 

 

 

(BLACK)

 

 

 

 

 

 

 

(BROWN)

(BROWN)

 

 

 

 

 

(WHITE)

(RED)

(BROWN)

 

 

 

 

 

(BLACK)

 

 

 

 

 

 

 

(BROWN)

 

 

 

 

 

 

 

(RED)

 

 

 

 

 

 

WHITE (HTL)

 

(GREEN)

 

 

 

 

 

(ORANGE)

 

 

 

 

 

YELLOW (H&G)

 

 

 

 

 

RED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GROUND

 

 

 

 

GREEN

 

IPI

BLACK

 

 

 

 

 

 

 

 

 

 

 

VALVE

 

 

 

 

 

 

REAR VIEW

 

 

IPI PILOT

G

Y

R

 

IPI

 

(BROWN)

R Y G

 

 

 

 

 

 

MODULE

(BROWN)

 

 

 

 

 

 

(RED)

(RED)

 

 

 

 

 

 

 

 

 

 

 

 

 

(BLACK)

(BLACK)

 

 

 

 

 

 

3V DC

 

 

 

 

FLAME

SOLENOID

FRONT VIEW

 

(RED)

 

 

 

 

 

 

FLAME ON (RED)

(ORANGE)

 

 

 

 

 

 

(YELLOW)

 

 

 

 

FLAME HIGH/LOW

(ORANGE)

FACTORY

 

(BLACK)

 

 

 

(BLACK)

 

CONNECTED

 

(WHITE)

 

 

TOGETHER

FIREBOX

FAN

 

(YELLOW)

(GROUND)

 

 

 

 

 

CONNECTION

 

FAN THEMOSTAT

 

 

 

TO HEAT ZONE

(BLACK)

 

 

 

 

 

 

 

 

 

 

AC

(BLACK)

 

 

 

 

 

PLUG

 

 

 

 

 

AUX

 

PLUG-ADP

BACK

 

 

GROUND PIGTAIL

CONNECTION

NOTE 1: BROWN AND RED WIRES FROM

 

LIGHT 1

GREEN

 

 

 

 

 

 

 

PVK-80ARE FOR THE VACUUM SWITCH

 

 

 

 

 

NOTE 2: BLACK, WHITE AND GREEN WIRES

 

 

 

 

 

RUN PVK-80MOTOR.

 

 

 

 

 

BACK

 

 

 

 

 

 

LIGHT 2

NOTE 3: GREEN WIRE FROM PVK-80SHOULD

TIE INTO GROUND A THE JUNCTION BOX

WHERE 110V SERVICE IS REQUIRED.

Figure 12.2 IPI Wiring diagram for optional PVK-80power vent termination cap

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

E. Junction Box Installation

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 12.4).

Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.4.

Make all necessary wire connections to the junction box/receptacle and reattach the junction box/receptacle to the outer shell.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

43

13 Finishing

A. Splatter Guard

The splatter guard is a piece of corrugated material used to protect the appliance during the installation process before finishing work on the whole hearth is complete. Splatter guards may be factory installed or accompany the door of the unit, depending on the fireplace model. Splatter guards must be removed before appliance is fired.

WARNING! Risk of Fire! Close the ball valve before installing the splatter guard to prevent accidental lighting. Remove the splatter guard before lighting the appliance.

Step 1. Turn off gas to valve. Red gas shutoff knob is located on ball valve. Disconnect the 3 volt transformer from the junction box. See Figure 13.1.

Figure 13.3

Figure 13.1

To install the Splatter Guard:

Step 2. Crease the bottom and side flaps of the splatter guard using the scored line as the guide. See Figure 13.2.

Figure 13.2

Step 3. Place the top side of splatter guard behind the left and right panel brackets and in front of the glass. See Figure 13.3.

44

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.)

Combustible Mantels

 

 

 

 

 

 

3-1/2IN.

 

 

 

 

 

 

 

FINISH WALL

 

 

 

 

 

 

 

COMBUSTIBLE

 

 

 

 

 

 

 

NO COMBUSTIBLES

 

 

 

 

 

 

IN THIS AREA

 

 

 

 

 

 

 

COMBUSTIBLE

39 IN.

 

 

 

 

 

FRAMING

 

 

 

 

 

 

 

METAL PANELS

 

 

 

 

 

 

(PROVIDED)

 

 

 

 

 

 

 

COMBUSTIBLE

 

 

 

 

 

 

PROJECTIONS

 

 

 

 

 

 

 

12 IN.

 

 

 

 

 

 

 

 

10-1/2IN.

 

 

 

 

11-12IN.

 

 

9 IN.

 

 

 

 

 

7-1/2IN.

 

 

 

 

 

 

 

6 IN.

 

 

 

 

 

 

 

4-3/4IN.

 

12 IN.

 

 

 

 

 

3 IN.

 

MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 IN. MIN.

 

 

 

 

 

 

6 IN. MIN.

 

NON-COMBUSTIBLE

 

 

 

 

 

 

FACING MATERIAL

 

 

TOP OF FIREPLACE

MIN. 1/2 IN. THICKNESS

 

 

 

 

 

 

 

 

OPENING

 

Height

in.

6

7

8

9

10

11

12

above

mm

152

178

203

228

254

279

305

opening

 

 

 

 

 

 

 

 

Horizontal

in.

3

4-3/4

6

7-1/2

9

10-1/2

12

Mantel

mm

76

121

152

191

228

267

305

distance

 

 

 

 

 

 

 

 

Figure 13.4 Minimum Vertical and Maximum Horizontal

 

 

Dimensions of Combustibles

 

 

 

Combustible Mantel Legs or Wall Projections

4 INCH

MINIMUM

UNLIMITED

NON-COMBUSTIBLE

MATERIAL

Figure 13.5 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

C. Facing Material

The appliance front metal surfaces may be covered with non-combustiblematerials only.

Non-combustiblematerials MUST be placed around the fi replace opening (see Figure 13.6)

Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers and door or removal of the right, left and bottom refractory panel for service.

Facing and/or fi nishing materials must never overhang into the glass opening.

Observe all clearances when applying combustible materials.

Seal joints between the fi nished wall and appliance top and sides using a 300 °F minimum sealant. Refer to Figure 13.7.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

45

NON-COMBUSTIBLE

ZONE

43 in.

60 in.

Figure 13.6 Noncombustible Facing Diagram

D. Finishing Materials Requirements

Note: Optional firescreen sits out1-1/2inches from the face of the fireplace. When using thin finishing material, you may want to use thickernon-combustiblebacker board to bring the finishing material flush with the fire screen. This is not required.

Use the two metal panels shipped with fi replace.

Unscrew the four screws holding two panels together.

Slide the two tapered tabs on bottom of each panel into slots of top surround.

Secure panels with sheet metal screws previously removed from panels.

The metal panels will cover the width of appliance and height of appliance to header board (11-1/2inch).

Cover entire face of appliance with non-combustiblematerials prior to applying finishing material, such as brick, stone or tile. See Figure 9.2, 9.3, 13.6 and 13.7.

The fi nishing material must NEVER pass the 1/2 inch metal edge around the opening and overhang into the glass opening.

VIEW FROM TOP OF APPLIANCE

 

 

7-1/2INCH MINIMUM

COMBUSTIBLE OK

 

NON-COMBUSTIBLE

 

MATERIAL

 

 

 

 

FINISH

NON-COMBUSTIBLE

WALL

 

FACING MATERIAL

 

 

 

60 in.

METAL

 

PANELS

 

 

 

 

43 in.

HIGH TEMPERATURE (300º F /149º C MIN.)

 

TOP AND SIDE SEAL JOINTS

 

Figure 13.7 Non-combustibleFinishing Material Requirements

46

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14.G.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the fi rebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Ember Placement

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place the ember material:

Remove the ash lip that is located in front of the glass.

Remove the side panels located in front of the glass.

Remove the pull mesh fi rescreen by unhooking from the fi replace.

Pull and release the six glass latches (3 per side) located on the sides of the glass frame.

Grasping the upper lip with one hand and the lower lip with the other, pull the bottom of the glass out fi rst. Guide the bottom while letting the top drop down under the top of the opening (see Section 14.G Fixed Glass Assembly).

There are two types of ember shipped with the unit. Embers for the burner surface and Mystic Embers for the fl oor of the unit.

Do NOT place embers between log #3 and log #4. They may disrupt the fl ames and are not visible.

Place Mystic Embers on the fl oor of unit. Use Mystic Embers to hide the pilot wires on left side of the burner.

NOTICE: Do NOT place Mystic Embers over lighted area of lens. Lens may melt if covered.

Save the remaining ember materials for use during fi replace servicing.

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

47

F. Install the Log Assembly

LOG PLACEMENT INSTRUCTIONS

Log Set Assembly: LOGS-ESCAPE42

Models: Escape-42DV

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

NOTE: If sooting occurs, the logs may need to be repositioned slightly to avoid excessive fl ame impingement.

CAUTION: Logs are fragile! Carefully remove the logs from the packaging.

NOTE: If logs rub against one another during positioning, the white inner material may become visible.Touch-uppaint may be applied to the white areas using a small brush or swab.DO NOT spray paint directly on surface of the logs. Reference service parts list for log touchup paint.

Step 1.

NOTE: If bulb and orange lens are already installed, proceed to Step 2.

Remove the bulb from its packaging and locate the sockets installed in the square cut outs in the fi rebox fl oor. The contacts on the bulb push into the two small holes in the socket top, as shown.

Place the framed orange lens on top of the fi rebox fl oor covering the bulb as shown. The four tabs on the lens frame go into the square cut out to help locate the lens.

6

3

5

4

 

 

 

1

1 7 8

1

2

2

48

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

Step 2.

Place the grate onto the burner. The back of the right tine drops into the hole on the right rear of the burner. Line the grate up so it is parallel with the front of the fi rebox. Be sure to push the grate all the way down to the fl oor.

LOG #1

 

 

 

 

(SRV2012-081)(Three):

 

 

There are quantity three (3) of Log

 

 

#1. Place one of the logs on the fl oor

 

 

of the fi replace on the left side of the

 

 

grate between the fi rebox and the

 

 

left grate tine. Place the second log

 

 

on the right side of the burner be-

 

 

tween the burner and the right grate

 

 

tine. The second log can be slightly

 

1

resting on the edge of the burner.

 

Place third log on top of the left side

1

1

of the burner. The burner ports will

be around the log. Do NOT cover

any burner ports with the log.

 

 

 

 

 

LOG #2 (SRV2012-082)(Two):

There are quantity 2 (two) of Log #2. Place one of the logs on the right side of the burner on the fl oor (see Figure A). The log will be in front of the orange Kapton lens.

Place the right end of the second log on the pilot bracket. The left end of the log should rest on the base of thefirebox See Figure B.

Figure A

Figure B

2 2

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

49

LOG #3

(SRV2052-083):

Place Log #3 onto the back of the burner. The log sits on top of the burner surface. The back of the log is pushed up against the back metal wall of the burner and the left end of the log is fl ush with the left edge of the metal wall.

LOG #4

(SRV2012-084):

Place Log #4 on top of the burner in front of Log 3. The triangle shaped groove in the bottom fi ts onto the right grate tine. The left end of the log will fi t the contour of the burner between the ports. DO NOT cover the burner ports.

LOG #5 (SRV2012-085):

Place Log #5 in front of Log #4. The groove in the bottom end of the log fi ts into the right vertical grate tine. The back of the log rests in the small fl at spot on top of Log #3.

FLUSH END

3

3

4

3

5

4

50

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

LOG #6

(SRV2052-086):

Place log #6 on the left side of the grate with the groove on the end of the log fi tting into the vertical left grate tine. The other end sits on the fl at spot of log #3.

LOG #7

(SRV2012-087):

Place log #7 on top of log #6. The groove in the front side of the log fi ts into the second vertical tine from the left of the grate. The center of the log rests in the flat spot on log #6.

LOG #8

(SRV2012-088):

Place Log #8 on top of Log #5. The fl at bottom of Log #8 sits on the large fl at area of Log #5. The burned end of Log #8 rests on the second vertical tine from the right of the grate. The tine fi ts on the burned out groove on the left end of the log.

Final Step:

Place MYSTIC EMBERS generously around on the fl oor of the fi replace. Do NOT put Mystic embers on the burner surface around the ports. Place embers around the pilot wires to disguise the wires from view.

6 3

7

6

5

8

2052-945B

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

51

G. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace as a complete assembly.

Removing Fixed Glass Assembly

Remove the ash lip that is located in front of the glass.

Remove the side panels located in front of the glass.

Remove the pull mesh fi rescreen by unhooking from the fi replace.

Pull and release the six glass latches (3 per side) located on the sides of the glass frame.

Grasping the upper lip with one hand and the lower lip with the other, pull the bottom of the glass outfirst. Guide the bottom while letting the top drop down under the top of the opening (see Figure 14.1).

Replacing Fixed Glass Assembly

Replace the glass door on the appliance. Pull out and latch the six glass assembly latches into the groove on the glass frame.

UPPER

LIP

GLASS

CLIP

Figure 14.1 Fixed Glass Assembly

H. Install the Mesh

The pull-typefi rescreen hangs on the three hanger brackets located above the glass.

I. Air Shutter Setting

Air shutter settings should be adjusted by a qualifi ed service technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

Air Shutter Settings

 

NG

LP

ESCAPE42-DV

3/8 in.

N/A

ESCAPE42-DVLP

N/A

11/16 in.

52

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

15 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualifi ed service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualifi ed service technician. Contact your dealer to arrange a service call by a qualifi ed service technician.

A. IntelliFire Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

A. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

The ignitor/module

 

connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

B. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

spark.

 

shorts in the wiring.

ule to pilot assembly. Verify connections underneath pilot assem-

 

 

bly are tight; also verify connections are not grounding out to metal

 

 

chassis, pilot burner, pilot enclosure, mesh screen if present, or any

 

 

other metal object.

 

 

 

 

C. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

D. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5

 

 

mm) away from “I” terminal on module. Place ON/OFF rocker switch

 

 

or wall switch in ON position. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode. Replace pilot if necessary.

 

 

 

2. Pilot won’t light,

A. No power or transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly.

voltage of transformer under load at spade connection on module

spark.

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

B. A shorted or loose connection in

Remove and reinstall the wiring harness that plugs into module.

 

wiring confi guration or wiring har-

Verify there is a tight fi t. Verify pilot assembly wiring to module. Re-

 

ness.

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

C. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

D. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF rocker switch or wall

 

 

switch in ON position. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fi ne.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

3. Pilot sparks, but

A. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits.

 

 

 

 

B. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

D. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

 

solenoid ohms readings.

age is below 2.7.

 

 

 

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

53

IntelliFire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

 

 

A. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

 

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify con-

 

ues to spark, and main

 

nections are not grounding out to metal chassis, pilot burn-

 

burner will not ignite.

 

er, pilot enclosure or screen if present, or any other metal

 

(If the pilot continues

 

object.

 

to spark after the

 

 

 

B. Poor fl ame rectifi cation or contaminated

With fi xed glass assembly in place, verify that fl ame is en-

 

pilot fl ame has been lit,

 

fl ame rectifi cation has

fl ame sensing rod.

gulfi ng fl ame sensing rod on left side of pilot hood. Flame

 

 

sensing rod should glow shortly after ignition. Verify cor-

 

not occurred.)

 

 

 

rect pilot orifi ce is installed and gas inlet is set to pressure

 

 

 

 

 

 

specifi cations. Clean fl ame sensing rod with emery cloth to

 

 

 

remove any contaminants that may have accumulated on

 

 

 

fl ame sensing rod.

 

 

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of ap-

 

 

 

pliance. Verify that wire harness is fi rmly connected to the

 

 

 

module.

 

 

 

 

 

 

D. Damaged pilot assembly or contami-

Verify that ceramic insulator around the fl ame sensing rod

 

 

nated fl ame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

fl ame sensing rod to white sensor wire. Polish fl ame sens-

 

 

 

 

 

ing rod with fi ne steel wool to remove any contaminants

 

 

 

that may have accumulated on fl ame sensing rod. Verify

 

 

 

continuity with a multimeter with ohms set at lowest range.

 

 

 

Replace pilot if any damage is detected.

 

 

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

 

switch or wall switch in ON position. If there is no spark at “I”

 

 

 

terminal module must be replaced. If there is a spark at “I”

 

 

 

terminal, module is fi ne.

 

 

 

 

 

54

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

 

 

 

 

A

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

C

 

 

 

 

 

 

 

MINIMUM 24"

 

 

 

 

 

 

 

 

VERTICAL

 

 

 

Ø D

 

E

 

 

REQUIRED

 

 

 

 

 

 

 

G

 

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

GAS LINE

 

 

 

 

 

 

 

 

ACCESS

 

 

 

 

 

R

T

 

 

 

 

 

 

 

I

 

N

 

 

 

 

Q

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

 

 

 

 

O

 

 

 

S

 

 

 

 

 

 

 

 

ELECTRICAL

 

 

 

 

 

 

 

OPTIONAL FIRESCREEN

J

 

 

P

 

 

 

SITS OUT 1-1/2INCHES

ACCESS

 

 

 

 

 

 

FROM UNIT FACE

 

 

 

 

 

 

 

 

Location

Inches

Millimeters

Location

Inches

Millimeters

 

 

A

48

1219

K

11-5/8

 

296

 

 

B

28-3/8

722

L

3-5/8

 

91

 

 

C

12

305

M

1

 

24

 

 

D

8

202

N

41-3/8

 

1052

 

 

E

1/2

12

O

42

 

1068

 

 

F

21

533

P

56-7/8

 

1445

 

 

G

24

609

Q

37

 

939

 

 

H

72-1/8

1831

R

52

 

1320

 

 

I

2-5/8

66

S

1-1/2

 

38

 

 

J

4-1/4

107

T

40-3/8

 

1062

 

Figure 16.1 Appliance Dimensions

 

 

 

 

 

 

 

 

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

 

55

B. Vent Components Diagrams

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pipe

Effective Length

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10-1/2in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Inches

Millimeters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Effective

DVP4

4

102

(267 mm)

 

 

 

 

 

 

 

 

 

 

 

 

45°

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Height/Length

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP6

6

152

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP12

12

305

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP24

24

610

 

 

 

4-7/8in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

( 276 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP36

36

914

 

 

 

 

 

 

 

 

 

10-7/8in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP Pipe (see chart)

DVP48

48

1219

 

 

 

 

 

 

 

 

 

(276 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP6A

3 to 6

76 to 152

 

 

 

 

 

 

 

 

DVP45 (45º Elbow)

 

 

 

 

 

 

 

 

 

 

DVP12A

3 to 12

76 to 305

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP12MI

3 to 12

76 to 305

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP24MI

3 to 24

76 to 610

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11-3/8in.

 

 

 

(289 mm)

 

10 in.

1 in.

 

 

(254 mm)

 

 

(25 mm)

 

 

 

 

 

 

 

7-3/8in.

 

 

 

(187 mm)

 

10 in.

 

1-1/4in. (32 mm)

 

(254 mm)

9-1/4in.

 

 

 

 

Assembled

 

(235 mm)

1/2 in. TYP

Height: 24 in./610 mm

 

13-1/4in.

(13 mm)

Diameter: 10 in./254 mm

 

 

 

(337 mm)

 

DVP-AS2

DVP-FS(Ceiling Firestop)

DVP90ST (90° Elbow)

12 in.

(305 mm)

1 in.

(25 mm)

10 in.

1- 1/2 in.

8 in.

(203 mm)

(254 mm)

(38 mm)

14 in.

 

 

UP

 

(356 mm)

 

 

5 in.

12 in.

 

(127 mm)

(305 mm)

 

 

 

6 in.

 

 

(152 mm)

DVP-HVS(Vent Support)

 

DVP-WS(Wall Shield Firestop)

Figure 16.2 DVP vent components

56

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than7-1/4in. (184 mm) aDVP-HSM-Bwill be required.

8 in.

(203 mm) Heat Shield

15-1/8in.

(384 mm)

 

 

Term Cap

Minimum

Maximum

 

 

Effective Length

Effective Length

 

Max

 

12 in.

Trap1

3-1/8in.

4-5/8in.

(305 mm)

Effective

79 mm

117 mm

DVP-TRAP

Length

 

 

Trap2

5-3/8in.

9-3/8in.

Horizontal Termination Cap

 

137 mm

238 mm

 

 

 

 

DVP-TRAP1

DVP-TRAP2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP-TRAPK1

 

 

 

 

 

 

 

DVP-TRAPK2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP-HPC1

DVP-HPC2

Figure 16.3 DVP vent components

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

57

B. Vent Components Diagrams (continued)

 

 

 

 

31 in.

 

 

 

 

 

(787 mm)

 

13-1/4in.

 

 

 

 

 

(367 mm)

 

 

24-5/8in.

 

 

 

 

(625 mm)

 

 

24-5/8in.

27-1/2in.

 

 

 

 

(625 mm)

(127 mm)

 

 

 

13-1/4in.

 

 

 

 

 

 

 

 

 

(367 mm)

RF6M

 

 

 

RF12M

 

Roof Flashing Multi-pak

 

 

 

 

Roof Flashing Multi-pak

 

 

 

 

 

13-3/4in.

5 in.

 

 

11-7/8in.

5 in.

(349 mm)

(127 mm)

 

 

(302 mm)

(127 mm)

13-3/4in.

 

 

13-7/8in.

 

 

 

 

(352 mm)

 

 

(349 mm)

 

 

 

 

 

 

 

 

 

BEK

 

 

 

DVP-BEK2

 

Trap Cap Brick Extension

 

 

DVP-HPCCap Brick Extension

 

 

11-5/8in.

 

 

 

 

 

(295 mm)

 

 

 

 

7-1/8in.

 

12-1/8in.

 

 

 

(308 mm)

 

 

(181 mm)

 

 

 

 

 

 

 

DVP-TRAPFL

 

5-3/4in.

 

 

 

 

(146 mm)

COOL-ADD

 

Flashing

 

 

 

 

 

 

 

Cap Shield

 

 

 

 

 

26 in.

 

 

13-7/8in.

9-1/2in.

 

 

 

(352 mm)

(241 mm)

 

660 mm

 

 

 

 

 

 

 

14 in.

 

 

 

DVP-HSM-B

 

(356 mm)

 

 

 

Extended Heat Shield

 

 

 

 

 

Figure 16.4 DVP vent components

 

 

DRC-RADIUS

 

 

 

Cap Shield

 

 

 

 

 

58

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

 

B. Vent Components Diagrams (continued)

 

 

7-3/8in.

 

 

 

 

 

(187 mm)

 

 

 

 

 

1-1/2in.

 

 

 

 

 

(38 mm)

 

 

 

 

 

 

 

 

3-7/8in.

 

 

 

17-3/4in.

 

(98 mm)

 

 

14 in.

 

 

 

 

(451 mm)

 

 

 

 

(356 mm)

 

 

 

 

 

 

 

 

10-1/2in.

 

 

 

 

 

(267 mm)

 

12 in.

 

 

 

DVP-TV

 

 

 

VerticalTermination Cap

 

(305 mm)

 

 

 

 

 

 

 

 

DVP-TB1

 

 

 

 

 

BasementVent Cap

 

 

 

 

 

 

 

12 in.

 

9 in.

 

305 mm

 

12-1/2in.

 

 

2-3/4in.

(229 mm)

 

 

 

 

(317 mm)

7-1/4in.

 

(70 mm)

 

 

 

 

 

 

 

 

 

 

 

(184 mm)

12-1/2in.

 

 

 

 

 

 

11-1/2in.

 

 

(318 mm)

 

 

(292 mm)

 

5-1/4in.

 

 

 

 

 

 

 

 

 

 

(133 mm)

 

 

12-1/4in.

 

 

 

 

(311 mm)

 

DVP-TVHW

 

16 in.

 

 

 

 

 

VerticalTermination Cap (Highwind)

 

(406 mm)

PVK-80

 

 

 

 

 

 

 

 

 

(For use with IPI and DSI appliances only.)

 

 

 

 

16-7/8in.

14 in.

 

7-1/4in.

 

 

1 in.

(184 mm)

 

 

(429 mm)

(356 mm)

(25 mm)

 

 

12 in.

 

 

14 in.

 

 

(305 mm)

 

 

 

 

 

7-1/8in.

 

(356 mm)

 

 

12-1/8in.

 

 

 

 

(181 mm)

 

 

 

 

(314 mm)

 

 

 

 

 

 

8-3/4in.

3/8 in. (10 mm)

 

 

1 in. (25 mm)

 

 

(222 mm)

 

 

 

 

 

 

 

 

 

7-3/4to10-3/8in.

 

 

1-5/8in.

 

 

(197 to 264 mm)

 

 

(41 mm)

 

 

 

 

 

 

 

 

DVP-FBHT

 

 

DVP-HPC

 

 

FireBrickTermination Cap

 

 

High Performance Cap

 

 

Figure 16.5 DVP vent components

 

 

 

 

 

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

59

B. Vent Components Diagrams (continued)

 

13-5/8IN.

EFFECTIVE LENGTH

346 mm

32 IN. (813 mm) MIN.

 

35 IN. (889 mm) MAX.

 

12-1/2IN.

318 mm

20-3/4IN.

527 mm

PVI-SLP

Power Vent Inline

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 ft. PV Wire Harness

PVI-WH10

20 ft. PV Wire Harness

PVI-WH20

40 ft. PV Wire Harness

PVI-WH40

60 ft. PV Wire Harness

PVI-WH60

80 ft. PV Wire Harness

PVI-WH80

100 ft. PV Wire Harness

PVI-WH100

Note: Wire harnesses required to power thePVI-SLPconnect to the appliance and are ordered separately fromPVI-SLP.Contact your dealer to order.

 

16 IN.

 

 

406 mm

 

 

4-1/2IN.

15 IN.

 

114 mm

 

(381 mm)

 

9-3/16IN.

 

 

 

(233 mm)

 

13-5/8

16-11/16IN.

16-11/16IN.

(346 mm)

424 mm

(424 mm)

12-1/2IN.

 

 

(318 mm)

SLP-LPC

 

 

SLP Low Profi le Cap

 

Figure 16.6 Vent Components

60

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11

D. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

2000-945

Printed in U.S.A. - Copyright 2011

64

Heat & Glo • Escape-42DV2052-900Rev. Y • 11/11