Heat & Glo LifeStyle BRAVO 704-902 User Manual

Size:
2.65 Mb
Download

Para obtener un ejemplar en Español de este Manual del propietario, visite www.heatnglo.com.

Pour demander un exemplaire en français de ce Manuel du propriétaire, visitez www.heatnglo.com.

Owner’s Manual

Installation and Operation

Model:

Bravo

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual with

and maintenance

these instructions for safe

party responsible for use

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance.

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard, Title 24 CFR, Part 3280 orStandard for Installation in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

1

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

Congratulations

Congratulations on selecting a Heat & Glo gas appliance —anelegant and clean alternative to wood burning appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new appliance, you’ll want to read and carefully follow all of the instructions contained in this Owner’s Manual. Pay special attention to all Cautions and Warnings.

This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this Owner’s Manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas appliance will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of appliance products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your appliance.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance.

Type of Gas

Gas and Electric

Information

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autres brevets americains et etrangers en attente).

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 20802 Kensington Boulevard, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas (Sorte De Gaz): This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1

in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglementsNATURAL GAS locaux ou, en l’absence de tels reglements, selon les codes d’installationCAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

Approved Minimum (De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

Maximum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

Minimum Manifold Pressure (Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

IN CANADA

 

Model:

XXXXXXXX

ALTITUDE:

0-0000FT.

0000-0000FT.

(Modele):

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

(Serie):

Model Number

Serial Number

2

Heat & Glo • Bravo • 704-902Rev. E • 7/08

Table of Contents

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4 E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 4 F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 4 G. Requirements for the Commonwealth of Massachusetts. . 5

2 Getting Started

A. Design and Installation Considerations . . . . . . . . . . . . . . . 6

B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6

C. Inspect Appliance and Components. . . . . . . . . . . . . . . . . . 6

3 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . . 8

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

D. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 10

5 Vent Information and Diagrams

A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

D. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 18 B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . 18 C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 19

7 Appliance Preparation

A. Securing and Leveling the Appliance. . . . . . . . . . . . . . . 20

8 Installing Vent Pipe

A. Assembly of Vent Sections (DVP Pipe) . . . . . . . . . . . . . . 21 B. Disassembly of Vent Sections . . . . . . . . . . . . . . . . . . . . . 23 C. Installing Heat Shield and Horizontal Termination Cap . . 24 D. Installing Roof Flashing and Vertical Termination Cap. . . 25

9 Gas Information

A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

10 Electrical Information

A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 29 B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 29 C. Intellifire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 29 D. Wall Switch (Required). . . . . . . . . . . . . . . . . . . . . . . . . . . 29 E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 31

11 Finishing

A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

C. Finishing Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

12 Appliance Setup

A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 36

B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

D. Lava Rock and Ember Placement . . . . . . . . . . . . . . . . . . 36

E. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

F. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

G. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

H. Air Shutter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

13 Operating Instructions

A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 41 B. Lighting Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 C. After Appliance is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 43

14 Troubleshooting

A. Intellifire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 44

15 Maintaining and Servicing Appliance

A. Maintenance Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

16 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 48

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 49

C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

D. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 56

E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Heat & Glo • Bravo • 704-902Rev. E • 7/08

3

1 Listing and Code Approvals

A. Appliance Certification

MODELS: Bravo

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance Heater

STANDARD: ANSIZ21.88-2000CSA2.33-M2000• UL307B

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

This model may be installed in a bedroom or bed-sittingroom in the USA and Canada.

B. Glass Specifications

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202 (Safety Glazing Certification CouncilSGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and02-31917.01).

C. BTU Specifications

Models

Maximum

Orifice

Size

(U.S. or Canada)

Input BTUH

(DMS)

 

 

 

 

 

US

23,000

42

Bravo (NG)

(0-2000FT)

 

 

 

CANADA

20,700

43

 

 

(2000-4500FT)

 

 

 

 

 

US

23,000

53

Bravo (LP)

(0-2000FT)

CANADA

20,700

54

 

 

(2000-4500FT)

 

 

 

 

D. High Altitude Installations

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

Note: This installation must conform with local codes. In the absence of local codes you must comply with theNational Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and theCAN/CGA B149 Installation Codes in Canada.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750oC,shall be considered non-combustible materials.

Heat & Glo Quality Systems registered by SGS ICS

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or whether plastered or unplastered shall be considered combustible materials.

4

Heat & Glo • Bravo • 704-902Rev. E • 7/08

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

G.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) inch in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

5

2 Getting Started

A. Design and Installation Considerations

C. Inspect Appliance and Components

Heat & Glo direct vent gas appliances are designed to

WARNING

operate with all combustion air siphoned from outside of

the building and all exhaust gases expelled to the outside.

Inspect appliance and components for damage.

No additional outside air source is required.

 

Damaged parts may impair safe operation.

CAUTION

• Do NOT install damaged components.

• Do NOT install incomplete components.

 

 

• Do NOT install substitute components.

Check building codes prior to installation.

Report damaged parts to dealer.

Installation MUST comply with local, regional, state and national codes and regulations.

 

• Consult local building, fire officials or authorities having jurisdic-

Carefully remove the appliance and components from

 

tion about restrictions, installation inspection, and permits.

 

the packaging.

 

 

 

 

• The vent system components and trim doors are shipped

When planning an appliance installation, it’s necessary to

 

in separate packages.

determine the following information before installing:

The gas logs may be packaged separately and must be

Where the appliance is to be installed.

 

field installed.

The vent system configuration to be used.

Report to your dealer any parts damaged in shipment,

Gas supply piping.

 

 

particularly the condition of the glass.

 

Read all of the instructions before starting the insta-

Electrical wiring.

 

 

 

llation. Follow these instructions carefully during the

Framing and finishing details.

 

 

installation to ensure maximum safety and benefit.

Whether optional accessories—devicessuch as a wall

 

 

 

 

switch, or remote control—aredesired.

 

 

WARNING

 

 

 

 

 

 

 

 

 

WARNING

 

 

Hearth & Home Technologies disclaims any

 

 

 

 

 

responsibility for, and the warranty will be voided

 

Keep appliance dry.

 

 

by, the following actions:

 

 

Installation and use of any damaged appliance or vent

 

Mold or rust may cause odors.

 

 

 

 

system component.

 

Water may damage controls.

 

 

 

 

Modification of the appliance or vent system.

 

 

 

 

 

 

 

 

 

 

Installation other than as instructed by Hearth & Home

B. Tools and Supplies Needed

 

 

Technologies.

Before beginning the installation be sure that the following

 

• Improper positioning of the gas logs or the glass door.

 

• Installation and/or use of any component part not approved

tools and building supplies are available.

 

 

 

by Hearth & Home Technologies.

 

 

 

 

 

 

Reciprocating saw

Framing material

 

Any such action may cause a fire hazard.

Pliers

 

Hi temp caulking material

 

 

 

Hammer

 

Gloves

 

 

 

Phillips screwdriver

Framing square

 

 

 

Flat blade screwdriver

Electric drill and bits (1/4 in.)

 

 

 

Plumb line

 

Safety glasses

 

 

 

Level

 

1/2 - 3/4 inch length, #6 or #8 Self-drillingscrews

Manometer

 

Voltmeter

 

 

 

Tape measure

 

Noncorrosive leak check solution

 

 

 

6

Heat & Glo • Bravo • 704-902Rev. E • 7/08

3 Framing and Clearances

Note:

Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

Illustrations/diagrams are not drawn to scale.

Actual installation may vary due to individual design preference.

A.Selecting Appliance Location

When selecting a location for your appliance it is important to consider the required clearances to walls (see figure 3.1).

WARNING

Fire Risk

Provide adequate clearance:

Around air openings

To combustibles

• For service access

Locate appliance away from traffic areas.

Note: For actual appliance dimensions refer to Section 16.

A

½

B

E

½

A

B

C

In addition to these framing dimensions, also reference the following sections:

Clearances and Mantel Projections (Section 3.C and 3.D)

Vent Clearances and Framing (Section 6).

 

B

Note: These dimensions

 

are for flush wall finishing

 

method. For a recessed

 

arch finishing method refer

 

to Option B in Finishing

 

(Section 11).

D

 

A

B

C

D

E

Inches

45-1/8

34-3/8

63-7/8

25-1/4

No maximum

Millimeters

1146

873

1622

641

 

Figure 3.1 Appliance Locations

Heat & Glo • Bravo • 704-902Rev. E • 7/08

7

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase.

Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with

high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

WARNING

Fire Risk.

Odor Risk.

Install appliance on hard metal or wood surfaces extending full width and depth of appliance.

Do NOT install appliance directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING

Fire Risk.

Construct chase to all clearance specifications in manual.

Locate and install appliance to all clearance

specifications in manual.

A

B

C *

D

FROM

TOP OF

FINISHING

E STRIP TO

CEILING

F

H

J G I

Clearance to Combustibles

 

 

A

B

C*

D

E

F

G

H

I

J

 

 

Rough

Rough

Rough

Rough

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

 

Opening

Opening

Opening

Opening

 

 

to Ceiling

Floor

Flooring

Appliance

Appliance

Appliance

 

 

(Vent Pipe)

(Height)

(Depth)

(Width)

 

 

 

 

 

 

 

 

 

Inches

10

44

25-1/4

35-3/8

34-7/8

0

0

1/2

1/2

36

 

 

 

 

 

 

 

 

 

 

 

 

 

Millimeters

25

1118

641

699

886

0

0

13

13

914

 

 

 

 

 

 

 

 

 

 

 

 

*For additional framing options and dimensions, see Section 11, Finishing.

Figure 3.2 Clearances to Combustibles

8

Heat & Glo • Bravo • 704-902Rev. E • 7/08

D. Mantel Projections

Note: All measurements in inches.

1 IN C H

 

31

M IN IM U M

 

C E IL IN G

 

18

TO

 

 

17

V E N T P IP E

 

 

 

16

 

14

15

 

9 1 /8

 

13

 

M IN .

 

12

 

 

 

11

 

 

1 0

3 1 /8

 

9

 

 

8

 

6

7

 

3 7 /8

 

5

 

 

 

T O P O F

T O P O F

F IN IS H IN G S T R IP

U N IT

Figure 3.3 Clearances to Mantels or Combustibles above Appliance

Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.)

Heat & Glo • Bravo • 704-902Rev. E • 7/08

9

4 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Explosion Risk.

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

(See Figure 4.4 for specific clearances)

Figure 4.1

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................

1.0*

Over 6/12 to 7/12.................................................

1.25*

Over 7/12 to 8/12.................................................

1.5*

Over 8/12 to 9/12.................................................

2.0*

Over 9/12 to 10/12...............................................

2.5

Over 10/12 to 11/12 .............................................

3.25

Over 11/12 to 12/12 .............................................

4.0

Over 12/12 to 14/12.............................................

5.0

Over 14/12 to 16/12.............................................

6.0

Over 16/12 to 18/12.............................................

7.0

Over 18/12 to 20/12.............................................

7.5

Over 20/12 to 21/12.............................................

8.0

* 3 foot minimum in snow regions

Figure 4.2 Minimum height from roof to lowest discharge opening

Figure 4.2 specifies minimum vent heights for various pitched roofs.

GAS, WOOD OR FUEL

 

OIL TERMINATION

B

 

GAS

C TERMINATION

A

 

 

 

 

 

 

 

 

 

 

 

Gas

Wood & Fuel Oil

 

Comments

 

Termination

Termination

 

 

 

 

A

6 in.

20 in. min.

Horizontal distance between terminations

B

20 in.

24 in. min.

Distance to perpendicular wall

C

18 in.

18 in.

Vertical distance between terminations

Figure 4.3 Multiple Vertical Termination

10

Heat & Glo • Bravo • 704-902Rev. E • 7/08

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M

 

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Q

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(See Note 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

 

 

T

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

Electrical

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

= VENT TERMINAL

X = AIR SUPPLY INLET

 

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

=

 

12 inches...............

clearances above grade, veranda,

 

K

=

3 ft. (U.S.A.)

 

clearance to a mechanical

 

 

 

 

 

(See Note 1)

porch, deck or balcony

 

 

 

 

 

6 ft. (Canada)

...........

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(powered) air supply inlet

B

=

 

12 inches

clearances to window or door

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L**

=

7 ft

(See Note 1)

clearance

above

paved

 

 

 

 

 

 

that may be opened, or to perma-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

sidewalk or a paved driveway

 

 

 

 

 

 

nently closed window. (Glass)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

located on public property

D*

=

 

18 inches

vertical clearance to unventilated

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M*** =

18 inches.................

 

clearance under veranda, porch,

 

 

 

 

 

 

soffit or to ventilated soffit located

 

 

 

 

 

 

 

 

 

 

 

 

deck, balcony or overhang

 

 

 

 

 

 

above the terminal

 

 

 

 

 

42 inches

 

vinyl

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*30 inches

for vinyl clad soffits and below

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

=

6 inches

 

clearance from sides of elec-

 

 

 

 

 

 

electrical service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(See Note 5)

 

trical service

 

 

 

 

 

 

 

 

 

 

 

 

F

=

 

9 inches

clearance to outside corner

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

=

12 inches

 

clearance above electrical

G

=

 

6 inches

clearance to inside corner

 

 

 

 

 

 

 

 

 

 

(See Note 5)

 

service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H

=

 

3 ft. (Canada) ........

not to be installed above a gas

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

meter/regulator assembly within 3

 

 

 

Alcove Applications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

feet (90cm) horizontally from the

 

 

N

 

=

 

6 inches ..................

 

non-vinylsidewalls

 

 

 

 

 

 

 

 

 

 

 

center-lineof the regulator

 

 

 

 

 

 

 

12 inches ................

 

vinyl sidewalls

 

 

 

 

 

I

=

 

3 ft. .......................

clearance to gas service regulator

 

 

P

 

=

 

8 ft.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

vent outlet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J

=

9 inches (U.S.A.)

 

 

 

 

 

 

 

 

 

 

 

Q MIN

 

 

 

 

 

RMAX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 inches (Canada) clearance to non-mechanical

 

 

 

 

1 cap

 

 

3 feet

 

 

 

 

2 x Q ACTUAL

 

 

 

 

 

 

 

 

 

air supply inlet to building or the

 

 

 

 

2 caps

 

 

6 feet

 

 

 

 

1 x Q ACTUAL

 

 

 

 

 

 

 

 

 

combustion air inlet to any other

 

 

 

 

3 caps

 

 

9 feet

 

 

2/3 x Q ACTUAL

 

 

 

 

 

 

 

 

 

appliance

 

 

 

 

4 caps

 

 

12 feet

 

 

1/2 x Q ACTUAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

**a vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

***only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor, or meets Note 2.

Note 1: On private property where termination is less than 7 feet above a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap shield is suggested. (See vents components page)

Note 2: Termination in an alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions specified for vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum between termination caps. 2.All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below the termination cap. 3.All gravity air intakes within 3 feet of a termination cap must be a minimum of 1 foot below the termination cap.

Figure 4.4 Minimum Clearances for Termination

Note 3: Local codes or regulations may require different clearances.

Note 4: Termination caps may be hot. Consider their proximity to doors or other traffic areas.

Note 5: Location of the vent termination must not interfere with access to the electrical service.

WARNING: In the U.S: Vent system termination is NOTpermitted in screened porches. You must follow side wall, overhang and ground clearances as stated in the instructions.

In Canada: Vent system termination is NOTpermitted in screened porches. Vent system termination is permitted in porch areas with two or more sides open. You must follow all side walls, overhang and ground clearances as stated in the instructions.

Hearth & Home Technologies assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

11

5 Vent Information and Diagrams

A. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

V1

First section (closest to appliance of vertical length

 

 

V2

Second section of vertical length

 

 

H1

First section (closest to appliance) of horizontal length

 

 

H2

Second section of horizontal length

 

 

WARNING

Fire Hazard. Explosion Risk. Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney flue serving a separate solid-fuelor gas burning appliance.

• Vent this appliance directly outside.

• Use separate vent system for this appliance.

May impair safe operation of this appliance or other appliances connected to the flue.

B. Use of Elbows

CAUTION

ALL vent configuration specifications MUST be followed.

This product is tested and listed to these specifications.

Appliance performance will suffer if specifications are not followed.

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 5.1).

Two 450 elbows may be used in place of one 900 elbow. On 450 runs, one foot of diagonal is equal to 8.5 inches horizontal run and 8.5 inches vertical run. A length of straight pipe is allowed between two 450 elbows (see Figure 5.1).

Vertica l

 

 

in.

 

.

1/2

12

in

 

8-

8-1/2in.

Horizontal

Figure 5.1

C. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

1.Pipe measurements are shown using the effective length of pipe (see Figure 5.2).

2.Measurements are made from the appliance outer wrap, not from the standoffs.

3.Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 4.1).

4.Vertical terminations are measured to bottom of termination cap.

5.Horizontal pipe installed level with no rise.

 

 

Pipe

Length/

 

 

 

 

Inches

 

 

 

 

 

DVP4

4

 

 

DVP6

6

Effective

DVP12

12

Height/Length

DVP24

24

 

 

DVP36

36

 

 

DVP48

48

 

 

DVP6A

3 to 6

 

 

DVP12A

3 to 12

 

 

DVP12MI

3 to 12

 

 

DVP24MI

3 to 24

 

 

 

 

Figure 5.2 DVP Pipe Effective Length

12

Heat & Glo • Bravo • 704-902Rev. E • 7/08

D. Vent Diagrams

WARNING

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between ceiling firestops.

ALWAYS maintain specified clearances around venting and firestop systems.

Install wall shield and ceiling firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

1. Top Vent - Horizontal Termination

One Elbow

Figure 5.3

Two Elbows

V1 Minimum

H1 Maximum

3 ft.

 

 

0.9 m

2 ft.

 

0.6 m

4 ft.

 

 

1.2 m

4 ft.

 

1.2 m

5 ft.

 

 

1.5 m

6 ft.

 

1.8 m

12 ft.

 

 

3.7m

20 ft.

 

6.1 m

V1

+ H1

= 40 ft. (12.2 m) Maximum

 

H1 = 20 ft. (6.1 m) Maximum

 

Note: When installing the TAOS surround and venting with one elbow, a straight section of venting (30 in. minimum)MUST be attached directly to starting collars on unit.

Note: The first elbow usedMUST always be DVP90ST.

V1 Minimum

H1 + H2 Maximum

3 ft.

0.9 m

2 ft.

0.6 m

4 ft.

1.2 m

4 ft.

1.2 m

5 ft.

1.5 m

6 ft.

1.8 m

12 ft.

3.7 m

20 ft.

6.1 m

V1 + H1 + H2 = 40 ft. (12.2 m) Maximum

H1 + H2 = 20 ft. (6.1 m) Maximum

Note: V1 MUST be a minimum of 3 feet unless using the TAOS surround. For TAOS surround, V1 minimumMUST be 30 in.

Note: The first elbow used

MUST always be DVP90ST.

Figure 5.4

Heat & Glo • Bravo • 704-902Rev. E • 7/08

13

1. Top Vent - Horizontal Termination

- (continued)

 

 

 

Three Elbows

V1 + V2 Minimum

H1 + H2 Maximum

 

3 ft.

0.9 m

2 ft.

0.6 m

 

4 ft.

1.2 m

4 ft.

1.2 m

 

5 ft.

1.5 m

6 ft.

1.8 m

 

12 ft.

3.7 m

20 ft.

6.1 m

 

V1 + V2 + H1

+ H2 = 40 ft. (12.2 m) Maximum

 

H1 + H2 = 20 ft. (6.1 m) Maximum

 

Note: V1 MUST be a minimum

 

of 3 feet unless using the TAOS

 

surround. For TAOS surround, V1

 

minimum MUST be 30 in.

 

 

Note: The first elbow used

 

MUST always be DVP90ST.

 

Figure 5.5

14

Heat & Glo • Bravo • 704-902Rev. E • 7/08

2. Top Vent - Vertical Termination

 

No Elbow

V1 = 46 ft. Max. (14.0 m)

8 F T. (2.4mm)

FLUE

OUTLET

Note: A 45° elbow may be attached directly to starting collars on unit only if used in conjunction with a return 45°

elbow AND terminating vertical with V = 8 feet MINIMUM.

A straight section of pipe can be used between the two 45° elbows.

Figure 5.6

Heat & Glo • Bravo • 704-902Rev. E • 7/08

15

Two Elbows

Figure 5.7

V1 Minimum

H1 Maximum

V2

3 ft.

0.9 m

2 ft.

0.6 m

*

4 ft.

1.2 m

4 ft.

1.2 m

*

 

 

 

 

 

5 ft.

1.5 m

6 ft.

1.8 m

*

12 ft.

3.7 m

20 ft.

6.1 m

*

V1 + V2 + H1 = 40 ft (12.2 m) Maximum *No specific restrictions on this value EXCEPT

V1 + V2 + H1 cannot exceed 40 ft (12.2 m)

Note: V1 MUST be a minimum of 3 feet unless using the TAOS surround. For TAOS surround, V1 minimumMUST be 30 in.

Note: The first elbow used

MUST always be DVP90ST.

16

Heat & Glo • Bravo • 704-902Rev. E • 7/08

2. Top Vent - Vertical Termination - (continued)

Three Elbows

IN S TA L L E D

H O R IZ O N TA L LY

Figure 5.8

 

V1

H1 + H2

V2

3 ft.

 

0.9 m

2 ft.

0.6 m

*

4 ft.

 

1.2 m

4 ft.

1.2 m

*

 

 

 

 

 

 

5 ft.

 

1.5 m

6 ft.

1.8 m

*

12 ft

 

3.7 m

20 ft.

6.1 m

*

H1 + H2 = 20 ft (6.1 m) Maximum

*No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 = 40 ft (12.2 m) Maximum

Note: V1 MUST be a minimum of 3 feet unless using the TAOS surround. For TAOS surround, V1 minimumMUST be 30 in.

Note: The first elbow used

MUST always be DVP90ST.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

17

6 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING

Fire Risk. Explosion Risk.

Maintain vent clearance to combustibles as specified.

Do not pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause fire.

3 in. TOP CLEARANCE

1 in. CLEARANCE AROUND VERTICAL SECTIONS

1 in. SIDE AND BOTTOM CLEARANCE

Figure 6.1 Pipe Clearances

Note: Heat shields MUST overlap by a minimum of1-1/2in. (38 mm).

The heat shield is designed to be used on a wall 4 in. to 7-1/4in. (102 mm to 184 mm) thick.If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required.

 

 

 

 

3 in . T O P

H E AT

 

 

C L E A R A N C E

 

 

 

 

H E A T

S H IE L D

 

 

 

 

S H IE L D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 in . C L E A R A N C E

W A L L

B O T T O M & S ID E S

S H IE L D

 

F IR E S T O P

 

 

 

W A L L

B. Wall Penetration Framing

10 in.

12 in.

B

A

A*

B

87-3/4in.

86-3/4in.

 

 

*Shows center of vent framing hole for top venting. The center of the hole is one (1) inch (25.4mm) above the center of the horizontal vent pipe.

Figure 6.3 Exterior Wall Hole

Combustible Wall Penetration

Frame a hole in a combustible wall for an interior wall shield firestop, (Figure 6.2) whenever a wall is penetrated. Use same size framing materials as those used in the wall construction. The wall shield firestop maintains minimum clearances and prevents cold air infiltration.

Non-CombustibleWall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable.

Whenever a non-combustiblewall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.

If your local inspector requires the wall shield firestop on both sides, then both wall shield firestops must have a heat shield attached to them.

Figure 6.2 Horizontal Venting Clearances to Combustible Materials

18

Heat & Glo • Bravo • 704-902Rev. E • 7/08

C. Vertical Penetration Framing

WARNING

Fire Hazard

Keep loose materials or blown insulation from touching the vent pipe.

National building codes recommend using attic shield to keep loose materials/ blown insulation from contacting vent.

Hearth & Home Technologies requires the use of an attic shield.

Installing the Ceiling Firestop

Frame an opening 10 inches by 10 inches whenever the vent system penetrates a ceiling/floor (see Figure 6.4).

Frame the area with the same sized lumber as used in ceiling/floor joist.

When installing a top vent vertical termination appliance the hole should be directly above the appliance, unless the flue is offset.

Do not pack insulation around the vent. Insulation must be kept away from the pipe.

Installing Attic Shield

Note: An additional ceiling firestop is not required if attic shield is used.

Frame opening for attic shield.

Attic shield may be installed above or below ceiling (see Figure 6.5).

Secure with three fasteners on each side.

Fold tabs at top of attic shield in toward vent pipe. Tabs must keep vent pipe centered within shield.

Field construct additional shield height if insulation is deeper than height of attic shield.

ATTIC ABOVE

10 IN. (254 MM)

10 IN.

(254 MM)

HOLE SHOULD MEASURE

10 IN. X 10 IN.

(254 MM X 254 MM)

INSIDE TO INSIDE

Figure 6.4

BEND TABS IN

AROUND PIPE

 

3 FASTENERS

 

PER SIDE

ATTIC SHIELD INSTALLED

ATTIC SHIELD INSTALLED

BELOW CEILING

ABOVE CEILING

Figure 6.5 Installing the Attic Shield

Heat & Glo • Bravo • 704-902Rev. E • 7/08

19

7 Appliance Preparation

A.Securing and Leveling the Appliance

WARNING

Fire Risk.

Prevent contact with sagging, loose insulation.

Do NOT install against combustible

materials such as exposed insulation, plastic and insulation backer.

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

The diagram shows how to properly position, level, and secure the appliance (see Figure 7.1). Nailing tabs are provided to secure the appliance to the framing members.

Place the appliance into position.

Level the appliance from side to side and front to back.

Shim the appliance as necessary. It is acceptable to use wood shims.

Bend out nailing tabs on each side.

Keep nailing tabs flush with the framing.

Secure the appliance to the framing by using nails or screws through the nailing tabs. Holes are provided in the basepan (inside the hearth) for securing to the floor.

N A IL IN G TA B S

(B O T H S ID E S )

Figure 7.1 Proper Positioning, Leveling and Securing

of an Appliance

WARNING

Fire Risk.

• ALWAYS maintain specified

clearances around the appliance.

• Do NOT notch into the framing around the appliance spacers. Failure to keep insulation, framing or other material away from the appliance may cause fire.

20

Heat & Glo • Bravo • 704-902Rev. E • 7/08

8 Installing Vent Pipe

A. Assembly of Vent Sections (DVP Pipe)

WARNING

Do not mix pipe, fittings or joining methods from different manufacturers.

WARNING

Fire Risk

Exhaust Fumes Risk

Impaired Performance of Appliance

• Overlap pipe slip sections at least 1-1/2inches.

Use pilot holes for screws.

Screws must not exceed one inch long.

Pipe may separate if not properly joined.

Attaching Vent to the Firebox Assembly

To attach the first pipe section to the collars, slide the male end of the inner vent of the pipe section over the inner collar on the firebox assembly. At the same time, slide the outer flue over the outer collar on the appliance. Push the pipe section into the appliance collar until all the lances (see Figure 8.1) have snapped in place. Tug slightly on the section to confirm it has completely locked into place.

Commercial, Multi-family(Multi-levelexceeding two stories), &High-RiseApplications

For Installation into Commercial, multi-family(multi-levelexceeding two stories) orhigh-riseapplications: All pipe joints must be sealed with high temperature silicone, including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 8.1

Only outer pipes are sealed. Do not seal the inner flue. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.

Note: The end of the pipe sections with the lances/tabs on it will face toward the appliance.

WARNING

Fire Risk Explosion Risk

If slip section seals are broken during the removal of the termination cap, gas will leak and a fire or explosion may occur.

Do not break silicone seals on slip sections.

Assembling Pipe Sections

Insert the inner flue of section A into the flared inner flue of section B.

Start the outer flue of section A over the outer flue of section B (see Figure 8.2). Note: The end of the pipe sections with the lances/tabs on it will face towards the appliance. Once both inner and outer flues are started, press section A onto section B firmly until all lances have snapped into place. Check to make sure they have snapped together (see Figure 8.3) and the seams are not aligned (see Figure 8.4). Tug slightly on section A to confirm it has completely locked into place. It is acceptable to use screws no longer than 1 inch to hold outer pipe sections together. If predrilling holes, do NOT penetrate inner pipe.

For 90° and 45° elbows that are changing the vent direction from horizontal to vertical, one screw minimum should be put in the outer flue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1 inch. If predrilling screw holes, do NOT penetrate inner pipe.

High Temperature Silicone Sealant

Commercial, Multi-family(multi-levelexceeding two stories), orHigh-riseApplications only

Figure 8.1 Lances

A

B

Figure 8.2

Figure 8.3

Heat & Glo • Bravo • 704-902Rev. E • 7/08

21

Note: Make sure that the seams are not aligned to prevent unintentional disconnection.

CORRECT

Figure 8.4 Seams

INCORRECT

Assembling Minimum Installations (MI) Sections

MI sections are non-unitizedso that they can be cut to a certain length. Cut these sections to length from the nonexpanded end (see Figure 8.5).

They can then be attached by first connecting the expanded end of the MI inner flue with the inner pipe from the adjacent pipe section and securing with three screws. The expanded portion of the MI inner flue must overlap completely with the unexpanded end of the adjacent pipe section.

The outer flue can then be inserted into the adjacent outer flue expanded end and attached to the next pipe section with three screws. The other end of the MI pipe section can then be attached by fitting another pipe section to it and snapping it together, as normal.

Note: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a hightemperature silicone sealant.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

Only outer pipes are sealed, sealing the inner flue is not required. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner.

Assembling DVP-12ASlip Sections

The outer flue of the slip section should slide over the outer flue of the pipe section and into (inner flue) the last pipe section (see Figure 8.6) .

Slide together to the desired length, making sure that a 1-1/2inch outer flue overlap is maintained between the pipe section and slip section.

The pipe and slip section need to be secured by driving two screws through the overlapping portions of the outer flues using the pilot holes (see Figure 8.7).

This will secure the slip section to the desired length and prevent it from separating. The slip section can then be attached to the next pipe section.

If the slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

Cut from this end

(outer)

Cut from this end

(inner)

Figure 8.5

Figure 8.6 Slip Section Pilot Holes

Figure 8.7 Screws into Slip Section

22

Heat & Glo • Bravo • 704-902Rev. E • 7/08

Securing the Vent Sections Vertical Sections

Vertical sections of pipe must be supported every 8 feet after the 25 foot maximum unsupported rise. The vent support or plumber’s strap (spaced 120° apart) may be used to do this (see Figure 8.8).

Horizontal Sections

Horizontal sections of vent must be supported every 5 feet with a vent support or plumber’s strap.

B. Disassembly of Vent Sections

To disassemble any two pieces of pipe, rotate either section (see Figure 8.10), so that the seams on both pipe sections are aligned (see Figure 8.11). They can then be carefully pulled apart.

WARNING

Fire Risk. Explosion Risk.

Combustion Fume Risk.

Use vent run supports per installation instructions.

Connect vent sections per installation instructions.

Maintain all clearances to combustibles.

Do NOT allow vent to sag below connection point to appliance.

Improper support may allow vent to sag or separate.

Figure 8.8 Securing Vertical Pipe Sections

Figure 8.9 Securing Horizontal Pipe Sections

Figure 8.10 Rotate Seams for Disassembly

Figure 8.11 Align and Disassemble Vent Sections

Heat & Glo • Bravo • 704-902Rev. E • 7/08

23

C. Installing Heat Shield and Horizontal Termination Cap

WARNING

Fire Hazard

Impaired performance of appliance

Telescoping flue section of termination cap MUST be used when connecting pipe section to termination cap.

Maintain a 1-1/2inch minimum overlap on telescoping flue section of termination cap.

Installing the Horizontal Termination Cap

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at outside edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 andCAN/CGA-B149 installation codes.

WARNING

Fire Risk

Exhaust Fumes Risk

Impaired Performance of Appliance

Overlap pipe slip sections at least 1-1/2inches.

Use pilot holes for screws.

Screws must not exceed 1 inch long.

Pipe may separate if not properly joined.

Heat Shield Requirements for Horizontal Termination

For all horizontally vented appliances, a heat shield MUST be placed one inch above the top of the vent between the wall shield firestop and the base of the termination cap.

There are two sections of the heat shield. One section is factory-attachedto the wall shield firestop. The other section isfactory-attachedto the cap. See Figure 8.12.

If the wall thickness does not allow the required 1-1/2inch (38 mm) heat shield overlap when installed, an extended heat shield(DVP-HSM-B)must be used.

Important Notice: Heat shields maynot be field constructed.

The extended heat shield (DVP-HSM-B)may need to be cut to length. You will attach the cut heat shield to the existing cap heat shield or wall shield firestop heat shield (refer to Figure 8.12) using the supplied screws. You MUST maintain a1-1/2in. (38 mm) overlap of the extended heat shield and the existing shields (both ends of the heat shield). The small leg on the extended heat shield should rest on the top of the vent (pipe section) to properly space it from the pipe section.

WARNING

Burn Risk

Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

HEAT SHIELD OR

REAR VENT

EXTENDED

HEAT SHIELD

HEAT SHIELD

1-1/2IN. (38 MM) MIN.

 

OVERLAP

WALL SHIELD FIRESTOP

 

INNER VENT

INTERIOR

SHEATHING

EXTERIOR

OUTER VENT

HEAT SHIELD EXTENSION NOT SHOWN.

Figure 8.12 Venting through the Wall

Note: Where required, an exterior wall flashing is available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

24

Heat & Glo • Bravo • 704-902Rev. E • 7/08

D.Installing Roof Flashing and Vertical Termination Cap

To install roof flashing see Figure 8.13.

For installation of vertical termination cap see minimum vent heights for various pitched roofs (see Figure 8.15).

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12.......................................1.0*

Over 6/12 to 7/12...........................1.25*

Over 7/12 to 8/12.............................1.5*

Over 8/12 to 9/12.............................2.0*

Over 9/12 to 10/12............................ 2.5

Over 10/12 to 11/12 ........................ 3.25

Over 11/12 to 12/12 .......................... 4.0

Over 12/12 to 14/12.......................... 5.0

Over 14/12 to 16/12.......................... 6.0

Over 16/12 to 18/12.......................... 7.0

Over 18/12 to 20/12.......................... 7.5

Over 20/12 to 21/12.......................... 8.0

* 3 foot minimum in snow regions

Figure 8.13 Minimum Height from Roof to Lowest

Discharge Opening

 

WARNING

Fire Risk.

Explosion Risk.

Inspect external vent cap regularly.

Ensure no debris blocks cap.

Combustible materials blocking cap may ignite.

Restricted air flow affects burner operation.

Caulk the gap between the roof flashing and the outside diameter of the pipe. Also caulk the perimeter of flashing that contacts roof surface as shown in Figure 8.15.

To attach the vertical termination cap, slide the inner collar of the cap into the inner flue of the pipe section and place the outer collar of the cap over the outer flue of the pipe section.

Secure with three screws into the outer flue. Secure the cap by driving the three self-tappingscrews (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 8.14).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 8.14

CAULK

Figure 8.15

Heat & Glo • Bravo • 704-902Rev. E • 7/08

25

Assembling and Installing Storm Collar

CAUTION

Sharp Edges

Wear protective gloves and safety glasses during installation.

Connect both halves of the storm collar with two screws (see Figure 8.16).

Wrap the storm collar around the exposed pipe section and align brackets. Insert a bolt (provided) through the brackets and tighten nut to complete storm collar assembly (see Figure 8.17).

Figure 8.17 Assembling the Storm Collar Around the Pipe

Slide the assembled storm collar down the pipe section until it rests on the roof flashing.

Caulk around the top of the storm collar (see Figure 8.14).

Figure 8.16 Assembling the Storm Collar

26

Heat & Glo • Bravo • 704-902Rev. E • 7/08

9 Gas Information

A. Fuel Conversions

C. Gas Connection

Before making gas connections ensure that appliance being installed is compatible with the available gas type.

Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts.

Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

B. Gas Pressures

Proper input pressures are required for optimum appliance performance. Gas line sizing requirements need to be made following NFPA51.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

WARNING

Verify inlet pressures.

• High pressure may cause overfire condition.

• Low pressure may cause explosion.

Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

Pressure requirements for appliance are shown in the table below. Minimum pressures must be met when other household gas appliances are operating.

Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 inches

11.0 inches

w.c.

w.c.

 

Maximum inlet gas pressure

14.0 inches

14.0 inches

w.c.

w.c.

 

Manifold pressure

3.5 inches

10.0 inches

w.c.

w.c.

 

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

Refer to Reference Section 16 for location of gas line access in appliance.

Note: Gas line may be run from either side of the appliance provided the hole in the outer wrap does NOT exceed2-1/2inches in diameter and does not penetrate the firebox.

WARNING

Gas Leak Risk

Support control when attaching pipe to prevent bending gas line.

Note: The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed withnon-combustible,unfaced insulation to prevent cold air infiltration.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

27

Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes.

Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.

WARNING

Fire or Explosion Hazard

Gas buildup during line purge may ignite.

Purge should be performed by qualified technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING

CHECK FOR GAS LEAKS

Explosion Risk

Fire Risk

Asphyxiation Risk

Check all fittings and connections.

Do not use open flame.

After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially-available,non-corrosiveleak check solution. Be sure

to rinse off all leak check solution following testing.

Fittings and connections may have loosened during shipping and handling.

WARNING

Fire hazard.

Do NOT change the valve settings.

• This valve has been preset at the factory.

• Changing valve settings may result in fire hazard or bodily injury.

HIGH ALTITUDE INSTALLATIONS

U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada.

When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate should be reduced by 4% for each 1000 feet above a 2000 foot elevation in the U.S.A., or 10% for elevations between 2000 and 4500 feet in Canada. If the heating value of the gas has been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.

If installing this appliance at an elevation above 4500 feet (in Canada), check with local authorities.

28

Heat & Glo • Bravo • 704-902Rev. E • 7/08

10 Electrical Information

A. Recommendation for Wire

This appliance requires 110-120VAC be wired to the junction box for proper operation of the appliance (Intellifire ignition).

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code, CSA C221.1.

B. Connecting to the Appliance

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

Incorrect wiring will damage millivolt valves.

Incorrect wiring will override IPI safety lockout and may cause explosion.

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

If using thermostat use one compatible with a millivolt gas valve system.

Follow parameters for locating thermostat (see individual thermostat instructions) to ensure proper operation of appliance.

Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.

Keep wire lengths short as possible by removing any excess wire length.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

C. Intellifire Ignition System Wiring

This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.1.

This appliance is equipped with an Intellifire control valve which operates on a 3 volt system.

This appliance is supplied with a battery pack and a 3 volt AC transformer, which requires the installation of the supplied junction box. It is highly recommended that the junction box be installed at this time to avoid reconstruction.

The battery pack requires two D cell batteries (not included).

NOTE: Batteries cannot be placed in the battery pack while using the 3 volt AC transformer. The transformer must be unplugged if the battery pack is used or battery life will be reduced.

Wiring to the battery pack is left disconnected in order to conserve battery life. In the case of a loss of power, simply connect red and black wire leads to activate battery power (connect red to red, black to black). The fireplace can be used as necessary. Once power (110 VAC) is restored, disconnect red and black wire leads to extend battery life.

CAUTION

Battery polarity must be correct or module damage will occur.

Optional Accessories Requirements

Wiring for optional accessories should be done now to avoid reconstruction.

D. Wall Switch (Required)

A wall switch must be installed of this fireplace. This will allow the unit to operate if the power goes out (battery operation).

Position the wall switch in the desired position on the wall. An assembly of 18 ft of 20 AWG is provided with the appliance to connect the wall switch to the appliance. Instead of the supplied assembly, wire with a length of 25 ft or less and a gauge of 20 AWG through 14 AWG is acceptable. The wire needs a jacket with a temperature rating of 140oF (60oC) or higher. At the appliance connect the wire to the ON/OFF switch pigtails.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

29

 

PLUG-IN

 

 

3V TRANSFORMER

 

 

ON/OFF

 

 

WALL SWITCH

 

 

 

FLAME SPARKER/

 

 

SENSOR

 

IGNITION

 

 

MODULE

 

 

(3V)

 

 

LOW VOLTAGE

 

SEE NOTE 1.

 

VALVE

LOW VOLTAGE

 

 

 

 

SEE NOTE 1

 

GROUND

REMOTE

 

 

 

 

CONTROL

NEUTRAL

 

HOT

WHITE WIRE CAN BE PLUGGED INTO ANY OF #1 - #5 LOCATIONS

ON THE NEUTRAL SIDE

BLACK WIRE CAN BE

PLUGGED INTO ANY OF #1 - #5 LOCATIONS

ON THE HOT SIDE

TRANSFORMER 3 VAC

PLUG IN

INTERMITTENT PILOT IGNITOR

IGNITION MODULE 3 VAC

 

 

WHT

 

 

ORG

 

 

GROUND TO

 

 

FIREPLACE

 

 

CHASSIS

 

BLK

 

RED

 

ORG

 

 

BRN

BRN

GRN

 

 

VALVE

THERMOSTAT

WIRE ASSEMBLY REMOTE JUMPER 2045-045

WIRE

NOTE 1: IGNITION MODULE, VALVE, PILOT AND WALL SWITCH OPERATE ON 3 VOLTS. 120 VAC IS REQUIRED AT JUNCTION BOX UNLESS EQUIPPED WITH BATTERY BACK-UP.

Figure 10.1 Intellifire Pilot Ignition (IPI) Wiring Diagram

CAUTION

Label all wires prior to disconnection when servicing controls.

Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

WARNING

Shock hazard.

Replace damaged wire with type 105O C rated wire.

Wire must have high temperature insulation.

30

Heat & Glo • Bravo • 704-902Rev. E • 7/08

E. Junction Box Installation

If the box is being wired from the OUTSIDE of the appliance:

Remove the cover plate located on the outer shell - right side (see Figure 10.3).

Install the supplied Romexconnector in the cover plate.

Feed the necessary length of wire through the connector.

Make all necessary wire connections and reattach the cover plate to the outer shell.

If the box is being wired from the INSIDE of the

appliance:

Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 10.3).

Pull the electrical wires from outside the appliance through this opening into the valve compartment.

 

 

Romex

 

 

Connector

 

 

14/2WG

 

 

Cover Plate

 

 

outside firebox

 

WHT

 

 

BLK

 

 

WHT

 

 

BLK

Copper

 

 

 

GRN wire

ground attached

 

to GRN screw with

 

inside box

GRN wire

 

 

Note: Do NOT wire

Figure 10.3

Junction Box Detail

110VAC to wall switch.

 

Feed the necessary length of wire through the connector.

Make all necessary wire connections to the junction box/receptacle and assemble the junction box/receptacle to the outer shell.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

31

11 Finishing

A. Mantel Projections

Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance.

Note: All

 

 

measurements

 

in inches.

 

31

1 IN C H

 

M IN IM U M

 

C E IL IN G

 

18

TO

 

 

17

V E N T P IP E

 

 

 

16

 

14

15

 

9 1 /8

 

13

 

M IN .

 

12

11

 

 

 

1 0

 

3 1 /8

9

 

 

8

 

 

7

3 7 /8

 

6

 

5

 

 

T O P O F

 

T O P O F

F IN IS H IN G S T R IP

U N IT

Figure 11.1 Clearances to Mantels or other Combustibles above Appliance

Figure 11.2 Mantel Leg or Wall Projections (Acceptable on both sides of opening.)

B. Facing Material

WARNING

Fire Risk.

Do NOT obstruct air inlet or outlet grilles.

Do NOT modify grilles.

Modifying or covering grilles could cause

temperature rise and fire hazard. Finishing materials must not interfere with:

Air flow through grilles or louvers.

Operation of louvers or doors.

Access for service.

1/2 INCH NON-COMBUSTIBLEBOARD REQUIRED ON UNIT FACE

NAILING

TABS

FINISHING

EDGE

TRIM

COMBUSTIBLE MATERIALS

MAY CONTACT AND COVER

FRONT AND SIDE AREAS

BELOW GLASS/FRONT

Figure 11.3 Noncombustible Facing Diagram

WARNING

Risk of Fire

Non-combustibleclearancesMUST be maintained.

Sheetrock, wood or other combustibles must

NOT be used as sheathing or facing in thenon-combustiblezone.

See Section 11 for proper clearances.

See Section 1 for combustible/noncombustible definitions.

WARNING

Fire Risk.

Finish all edges and fronts to clearances and specifications listed in manual.

Black metal appliance front may be covered with noncombustible material only.

Do NOT overlap combustible materials onto appliance front.

Install combustible materials only up to specified clearances on top, front and side.

Seal joints between the finished wall and appliance top and sides using only a 300º F minimum sealant.

32

Heat & Glo • Bravo • 704-902Rev. E • 7/08

C. Finishing Styles

This model has multiple installation and finishing options. The following section describe three basic installations.

Note: A 1/2 inch clearance must be maintained between combustible materials and the front face of the fireplace.

OPTION A: Flush Wall Finish

Kiva-stylefinished in a straight wall (see Figure 11.4).

Figure 11.4 Flush wall installation

Unit is installed using framing dimensions found in Figure 3.2.

Do not use nailing tabs provided on unit sides for Option A.

Nailing tabs are attached to the top of the unit. Install nailing tabs using screws on upper unit sides (see Figure 11.3).

This places unit back 1/2 inch from framing studs such that drywall or other material can be brought directly across non-combustibleboard up to finish edge trim.

WARNING

Fire Risk.

1/2 inch non-combustibleboard installed on front face of fireplace MUST remain if using combustible finishing materials.

A cardboard template is printed on unit shipping carton and may be used to help cut drywall or other finishing materials. Simply cut along line and use it as a template.

Drywall or other finishing materials may be finished all the way up to the finishing edge trim or unit front face, but MUST NOT extend inside of finishing edge trim.

CAUTION

Finishing materials cut inside the provided template will cause the door to not fit.

Finishing materials may be fastened or secured to unit below the glass/front opening.

OPTION B: Kiva-styleArch

The second installation option requires the construction of a kiva-stylearch. This option recesses the unit into the wall such that construction of a hearth is not necessary (see Figure 11.5).

5 INCH

MAXIMUM

DEPTH

INCLUDING

WALL FINISH

MATERIAL

Figure 11.5

Framing depth increases from that shown in Figure 3.2, (Dimension C). Dimension C will vary depending on the depth of the desired kiva-stylearch (see Figure 11.5).

Once depth of desired kiva-stylearch is determined (minimum of3-3/32inches and maximum 5 inches), add that to Dimension C from Figure 3.2. Level, set and secure fireplace using nailing tabs provided on fireplace sides. Secure with screws or nails into BACK of framing studs.

Kiva-stylearch dimensions: Maximum depth equals 5 inches (includes finish wall surface). Minimum depth equals3-3/32inches.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

33

Note: Previous numbers are for combustible construction numbers. Arch may protrude up to5-1/2inches maximum as measured from unit front face.

Note: Thekiva-stylearch depth may be any size if using noncombustible materials i.e. concrete, steel, plaster, etc.

A template is provided on unit shipping carton. Simply cut along the line and use as a template when constructing kiva-stylearch (see Figure 11.6).

CAUTION

Template for kiva-stylearch represents MINIMUM inside dimensions. When constructingkiva-stylearch, you must add thickness of finishing materials to achieve proper size of finished arch.

BACKING

MATERIAL

KIVA-STYLEARCH

STRUCTURE

FINISHING

MATERIAL

Figure 11.6

Inside of the kiva-stylearch can be finished using combustible materials. For example, thin drywall may be layered to form around curved arch.

OPTION C: SOUTHWESTERN kiva-style

The third installation option illustrated is a corner-installa-tion with custom finishing. This option requires advanced finishing methods involving either combustible ornon-com-bustible construction materials (see Figure 11.7).

Figure 11.7

A template is provided on the unit shipping carton. Simply cut along the line and use as a template for construction purposes.

The cardboard template provided represents MINIMUM inside dimensions of the finished wall surface.

If finishing with plaster or drywall, a finish edge trim is provided around door front on unit. Finishing materials MUST not extend inside of the finish edge trim.

CAUTION

Finishing materials cut inside the provided template or inside finish edge trim will cause the door not to fit.

WARNING

Fire Risk.

Follow minimum specified clearances found in Section 16, (Appliance Dimensions Diagram) and on fireplace exterior if using combustible framing materials.

34

Heat & Glo • Bravo • 704-902Rev. E • 7/08

OPTION D: Flush Wall Finish with Luxor Surround

Kiva-stylefinished in a straight wall (see Figure 11.8).

3-in.GAP

SHEETROCK

EDGE

FINISHING STRIP

Figure 11.8 Flush wall installation with Luxor Surround

Unit is installed using framing dimensions found in Figure 3.2.

Do not use nailing tabs provided on unit sides for Option D.

Nailing tabs are attached to the top of the unit. Install nailing tabs using screws on upper unit sides (see Figure 11.3).

This places unit back 1/2 inch from framing studs such that drywall or other material can be brought directly across non-combustibleboard up to finishing strip.

WARNING

Fire Risk.

1/2 Inch non-combustibleboard installed on front face of fireplace MUST remain in place if using combustible finishing materials.

A cardboard template is printed on unit shipping carton and may be used to help cut drywall or other finishing materials. Simply cut along line and use it as a template. For Luxor Surround, cut an additional 3 in. wider than the template.

ÎOPTION E: Corner Mount with Taos Surround

Unit must be placed on 5 3/4” tall platform. Platform should not exceed unit footprint. See Figure 11.10 Install unit in corner as tight as minimum clearances allow. If necessary, shim unit (up to 1/8”) so that gap between unit facing and Taos arch is even throughout as shown in Figure 11.10.

Follow instructions included with Taos Surround for mounting surround to walls.

Figure 11.9 Taos Surround on Platform

12-1/8in.

27-3/4in.

7-3/4in.

34-3/8in.

5-3/4in.

Figure 11.10 Platform Dimensions

EVEN GAP

Figure 11.11 Even Gaps All Around.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

35

12 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 16.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

Using non-listedaccessories voids warranty.

Using non-listedaccessories may result in a safety hazard.

Only Hearth & Home Technologies

approved accessories may be used safely.

D. Lava Rock and Ember Placement

WARNING

Explosion Risk.

Follow ember placement instructions in manual.

Do NOT place embers directly over burner ports.

Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Placing the Lava Rock

Place the lava rock on the bottom of the firebox. Evenly spread the lava rocks with your hand.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

Embers CANNOT be placed directly over ports.

When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place thedime-sizeember pieces near the ports, but not on the ports (see Figure 12.1). Failure to follow this procedure will likely cause lighting and sooting problems.

Place material near ports but do NOT cover port openings.

EMBER

M ATERIA L

Figure 12.1 Placement of Embers

Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

36

Heat & Glo • Bravo • 704-902Rev. E • 7/08

E. Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

CAUTION: Logs are fragile!

Carefully remove the logs from the packaging.

Before placing logs, check

 

that the sensor on the pilot

 

assembly

does not

contact

 

the burner.

 

1

Remove

shipping

bracket

and tie straps from the burn-

er and grate.

 

 

Place the lava rock on the

 

bottom of the firebox. Evenly

 

spread the lava rocks with

 

your hand.

 

 

 

 

 

 

 

 

 

SENSOR

 

 

 

 

LEFT LOG

 

RIGHT LOG

TAB

 

1

TAB

 

 

 

 

 

 

Log Assembly: LOGS-BRAVO

2

4

5

6

 

3

 

 

TAB

TIE STRAPS

GRATE

BURNER

Shipping Bracket

ADJUST LOG SO

GROOVE FOR

SURFACE IS FLUSH

LOG #2

1

LOG #1 (SRV750-703): Place log #1 between log tabs on left side and right side of the burner. Place such that

bottom surface of log rests on burner surface (left).

704-936C

Heat & Glo • Bravo • 704-902Rev. E • 7/08

37

2

RIGHT

 

2

GRATE

 

 

TINE

 

 

 

 

 

 

LOG #2 (SRV750-705): Place the top of log #2 in the groove on log #1. Place the base of the log on the inside of the outer right grate tine with the grate tine fitting in the groove on log #2.

GROOVE FOR

LOG #4

3

3

 

LOG #3 (SRV750-706): Place log #3 with the base on the inner right grate tine. The top of the log should be placed so that it doesn’t cover any ports on the burner.

GROOVE

FOR

LOG #5

LOG

 

2

LOG

LEFT

4

2

TAB

4

TAB

GRATE

 

 

 

 

 

 

TINE

 

 

 

 

 

 

 

 

 

 

 

 

 

GROOVE

 

LOG #4 (SRV750-704): Place log #4 such that the groove mates with the left grate tine. The upper end of the log should mate with the flat spot on log #2.

38

Heat & Glo • Bravo • 704-902Rev. E • 7/08

GROOVE

FOR

LOG #6

5

5

 

LOG #5 (SRV704-702): Place log #5 on right side of the grate. Position the base of the log on the log tab. The log tab should insert into slot feature on back side of log. Place the top of the log into the groove on log #1.

6

 

6

 

 

 

 

 

LOG #6 (SRV704-701): Place log #6 on left side of grate. Position the base of the log on the log tab. Log tab should insert into slot feature on back side of log. Place the top of the log into flat spot on log #1.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

39

F. Glass Assembly

WARNING

Handle glass doors with care.

Inspect the gasket to ensure it is undamaged.

Inspect the glass for cracks, chips or scratches.

Do NOT strike, slam or scratch glass.

Do NOT operate appliance with glass door removed, cracked, broken or scratched.

Replace glass door assembly as a complete appliance.

Removing Glass Assembly

Unscrew the two top wing bolts and unlatch the two bottom spring clips (see Figure 12.2).

Remove the front trim door and the glass door from the appliance.

Replacing Glass Assembly

Replace the glass door and a front trim door on the appliance. Pull out and latch the spring clips into the tabs on the glass frame and tighten the top wing bolts.

GLASS

CLIPS

Figure 12.2 Glass Assembly

G. Grilles and Trim

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other noncombustible materials can be used to cover up the gap between the sheet rock and the appliance.

H. Air Shutter Settings

 

NG

LP

Burner

1/8 in.

1/2 in.

40

Heat & Glo • Bravo • 704-902Rev. E • 7/08

13 Operating Instructions

A. Before Lighting Appliance

This appliance has an Intellifire ignition system.

CAUTION

If installing Intellifire ignition battery backup:

Do not install batteries if the backup mode may not be used for extended time.

Batteries may leak.

Install batteries only when needed for power outage.

Before operating this appliance have a qualified technician:

Remove all shipping materials from inside and/or underneath the firebox.

Review proper placement of logs, rockwool, lava rock, and vermiculite.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position.

Ensure that the flow of combustion and ventilation air is not obstructed (front grilles and vent caps).

Glass door must be in place when appliance is operating.

Risk of:

• Combustion Fumes

• Fire

Do NOT operate appliance with glass door removed.

Open viewing glass for servicing only.

Glass door MUST be in place and sealed before operating appliance.

Only use glass door certified for use with appliance.

Glass replacement should be done by qualified technician.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. Do NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

41

B. Lighting Appliance

Intellifire Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. Do not try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

CAUTION:

Hot while in operation. Do not touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies appliance, please refer to www.fireplaces.com.

Final Inspection by ______________________________

LIGHTING

INSTRUCTIONS (IPI)

1.Turn off all electric power to the appliance.

2.This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand.

GAS

VALVE

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you don’t smell gas, go to next step.

4.Turn on all electric power to the appliance.

5.To light the burner, flip the ON/OFF switch to the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6.If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Turn off all electric power to the appliance if service is to be performed.

2.Flip ON/OFF switch to the “OFF” position.

593-913D

42

Heat & Glo • Bravo • 704-902Rev. E • 7/08

C. After Appliance is Lit

Initial Break-inProcedure

When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.

Note: The appliance should be run three to four hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the appliance for an additional 12 hours. This will help to cure the products used in the paint and logs.

During this break-inperiod it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the appliance’s initial burning.

WARNING

Fire Risk.

High Temperatures.

Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air.

Do NOT place combustible items on top of or in front of appliance.

Keep furniture, draperies away from appliance.

CAUTION

Prevent accidental appliance operation when not attended.

Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

Property damage possible from elevated temperatures.

CAUTION

Smoke and odors released during initial operation.

Open windows for air circulation.

Leave room during initial operation.

Smoke may set off smoke detectors.

Smoke and odors may be irritating to sensitive individuals.

WARNING

Fire Hazard.

Keep combustible materials, gasoline and other flammable vapors and liquids clear of appliance.

• Do NOT store flammable materials in the appliance’s vicinity.

Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids in this appliance.

Combustible materials may ignite.

D. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation of the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

condensation will disappear.

 

 

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appliance is al-

lowed to burn for 20 to 40 minutes.

 

 

 

 

When first operated, this appliance may release an odor for the first several hours. This is

Odor from appliance

caused by the curing of the paint and the burning off of any oils remaining from manufactur-

ing. Odor may also be released from finishing materials and adhesives used around the

 

 

appliance.

 

 

Film on the glass

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See

 

your dealer.

 

 

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the appliance.

 

 

Is it normal to see the pilot flame burn

In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off when

continually?

ON/OFF is turned off. In a standing pilot system the pilot will always stay on.

 

 

Heat & Glo • Bravo • 704-902Rev. E • 7/08

43

14 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the

corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

A. Intellifire Ignition System

Sympton

Possible Cause

Corrective Action

1. The ignitor/module makes

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor

noise, but no spark.

 

are connected to correct terminals on module and pilot assembly.

 

 

Reversed wires at the module may cause system to make sparking

 

 

noise, but spark may not be present at pilot hood.

 

 

 

 

b. Loose connections or elec-

Verify no loose connections or electrical shorts in wiring from mod-

 

trical shorts in the wiring.

ule to pilot assembly. Rod closest to pilot hood should be ignitor.

 

 

Verify connections underneath pilot assembly are tight; also verify

 

 

connections are not grounding out to metal chassis, pilot burner,

 

 

pilot enclosure, mesh screen if present, or any other metal object.

 

 

 

 

c. Ignitor gap is too large.

Verify gap of igniter to pilot hood. The gap should be approximately

 

 

.17 inch or 1/8 inch.

 

 

 

 

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF Rocker switch or wall

 

 

switch in ON position. Hold ground wire about 3/16 inch away from

 

 

“I” terminal on module. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

2. Pilot won’t light, there is no

a. Transformer installed cor-

Verify that transformer is installed and plugged into module. Check

noise or spark.

rectly.

voltage of transformer under load at spade connection on module

 

 

with ON/OFF switch in ON position. Acceptable readings of a good

 

 

transformer are between 3.2 and 2.8 volts AC.

 

 

 

 

b. A shorted or loose connec-

Remove and reinstall the wiring harness that plugs into module.

 

tion in wiring configuration or

Verify there is a tight fit. Verify pilot assembly wiring to module.

 

wiring harness.

Remove and verify continuity of each wire in wiring harness.

 

 

 

 

c. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

d. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

 

 

ignitor wire “I” from module. Place ON/OFF Rocker switch or wall

 

 

switch in ON position. Hold ground wire about 3/16 inch away from

 

 

“I” terminal on module. If there is no spark at “I” terminal module

 

 

must be replaced. If there is a spark at “I” terminal, module is fine.

 

 

Inspect pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

3. Pilot lights but continues to

a. A shorted or loose connec-

Verify all connections to wiring diagram in manual. Verify connec-

spark, and main burner will not

tion in sensor rod.

tions underneath pilot assembly are tight. Verify connections are

ignite. (If the pilot continues to

 

not grounding out to metal chassis, pilot burner, pilot enclosure or

spark after the pilot flame has

 

screen if present, or any other metal object.

been lit, flame rectification has

 

 

not occurred.)

 

 

 

 

 

44

Heat & Glo • Bravo • 704-902Rev. E • 7/08

Intellifire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

3. (Continued) - Pilot lights

b. Poor flame rectification or contaminated

Verify that flame is engulfing sensor rod. If the pilot assem-

but continues to spark,

sensor rod.

bly does not have a ground strap, consider installing one

and main burner will not

 

to increase flame rectification. Verify correct pilot orifice is

ignite. (If the pilot contin-

 

installed and inlet gas specifications. Flame carries recti-

ues to spark after the pilot

 

fication current, not the gas. If flame lifts from pilot hood,

flame has been lit, flame

 

the circuit is broken. A wrong orifice or too high an inlet

rectification has not oc-

 

pressure can cause pilot flame to lift. The sensor rod may

curred.)

 

be contaminated. Clean sensor rod with emery cloth.

 

 

 

 

c. Module is not grounded.

Verify that module is securely grounded to metal chassis

 

 

of appliance. Verify that wire harness is firmly connected to

 

 

module.

 

 

 

 

d. Damaged pilot assembly or dirty sensor

Verify that ceramic insulator around the sensor rod is not

 

rod.

cracked, damaged, or loose. Verify connection from sen-

 

 

sor rod to white sensor wire. Clean sensor rod with emery

 

 

cloth to remove any contaminants that may have accumu-

 

 

lated on sensor rod. Verify continuity with a multimeter with

 

 

ohms set at lowest range.

 

 

 

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF posi-

 

 

tion. Remove ignitor wire “I” from module. Place ON/OFF

 

 

Rocker switch or wall switch in ON position. Hold ground

 

 

wire about 3/16 inch away from “I” terminal on module. If

 

 

there is no spark at “I” terminal module must be replaced.

 

 

If there is a spark at “I” terminal, module is fine. Inspect

 

 

pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

4. Pilot sparks, but Pilot

a. Correct gas supply.

Verify that incoming gas line ball valve is “open”. Verify that

will not light.

 

inlet pressure reading is within acceptable limits, inlet pres-

 

 

sure must not exceed 14 in. W.C.

 

 

 

 

b. Ignitor gap is too large.

Verify that spark gap from ignitor to pilot hood is .17 in. or

 

 

1/8 in.

 

 

 

 

c. Module is not grounded.

Verify module is securely grounded to metal chassis of

 

 

appliance.

 

 

 

 

d. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batter-

 

solenoid ohms readings.

ies if voltage is below 2.7.

 

 

 

Heat & Glo • Bravo • 704-902Rev. E • 7/08

45

15 Maintaining and Servicing Appliance

A. Maintenance Tasks

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

Turn off gas.

Turn off electricity to appliance.

Disable remote control, if one is present.

Ensure appliance is completely cooled.

After servicing:

Replace any screen or barrier that was removed.

Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

Condition of doors, surrounds and fronts.

Condition of glass, glass assembly and glass seal.

Obstructions of combustion and ventilation air.

Condition of logs.

Condition of firebox.

Burner ignition and operation.

Burner air shutter adjustment

Gas connections and fittings.

Obstructions of termination cap.

Clean:

Glass

Air passageways, grilles,

 

control compartment

Burner, burner ports

Risk of:

Fire

Delayed ignition or explosion

Exposure to combustion fumes

Odors

CAUTION

Handle glass assembly with care.

Note: Clean glass after initial3-4hours operation.Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when hot.

Turn off appliance after 3-4hours of operation and ALLOW TO COOL.

Remove and clean glass assembly.

Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

• Ensure no debris blocks cap.

• Combustible materials blocking cap may ignite.

• Restricted air flow affects burner operation.

46

Heat & Glo • Bravo • 704-902Rev. E • 7/08

Inspect

 

Maintenance Tasks

 

 

Doors, Surrounds

1. Assess condition of screen and replace as necessary.

and Fronts

 

Recommend addition of screen if one is not present.

 

2.

Inspect for scratches, dents or other damage and repair as necessary.

 

 

 

 

3.

Verify no obstructions to airflow through the louvers.

 

 

 

 

4.

Verify maintenance of proper clearance to combustible household objects.

 

 

Gasket Seal, Glass

1. Inspect gasket seal and its condition.

Assembly and Glass

 

 

2.

Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat.

 

 

 

 

 

3.

Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

4.

Verify that latches engage properly, clip studs are not stripped, and glass attachment components are intact

 

 

and operating properly. Replace as necessary.

 

5.

Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be removed.

 

 

 

Valve Compartment

1.

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw

and Firebox Top

 

tips that have penetrated the sheet metal are sharp and should be avoided.

 

2.

Remove any foreign objects.

 

 

 

 

3.

Verify unobstructed air circulation.

 

 

 

Logs

1.

Inspect for broken, damaged, or missing logs. Replace as necessary.

 

 

 

 

2.

Verify correct log placement and no flame impingement causing sooting. Correct as necessary.

 

 

 

Firebox

1.

Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.

 

 

 

 

2.

Replace appliance if firebox has been perforated.

 

 

 

Burner Ignition and

1.

Verify burner is properly secured and aligned with pilot or igniter.

Operation

 

 

2.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

 

 

 

 

 

3.

Replace ember materials with new dime-sizeand shape pieces. Do not block ports or obstruct lighting paths.

 

 

 

 

4.

Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.

 

 

 

 

5.

Inspect for lifting or other flame problems.

 

 

 

 

6.

Verify air shutter is clear of dust and debris.

 

 

 

 

7.

Inspect orifice for soot, dirt or corrosion.

 

 

 

 

8.

Verify manifold and inlet pressures. Adjust regulator as required.

 

 

 

 

9.

Inspect pilot flame strength. Clean or replace orifice as necessary.

 

 

 

10. Inspect thermocouple/thermopile or IPI sensor rod for soot, corrosion and deterioration. Clean with emery

 

 

cloth or replace as required.

 

11. Verify millivolt output. Replace as necessary.

 

 

Venting

1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.

 

 

 

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

 

 

 

3.

Verify that termination cap clearance to subsequent construction (building additions, decks, fences or

 

 

sheds) has been maintained.

 

4.

Inspect for corrosion or separation.

 

 

 

 

5.

Verify weather stripping, sealing and flashing remains intact.

 

 

 

 

6.

Inspect draft shield to verify it is not bent, damaged or missing.

 

 

Remote controls

1. Verify operation of remote.

 

 

 

 

2.

Replace batteries in remote transmitters and battery-poweredreceivers.

 

 

 

 

3.

Verify batteries have been removed from battery back-upIPI systems to prevent premature battery failure

 

 

or leaking.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

47

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

K

L

Ø J

 

 

I

 

M

 

 

 

A

 

ELECTRICAL

H

 

 

ACCESS

N

 

 

 

GAS LINE

 

 

 

ACCESS

B

C

G

 

D

 

 

 

 

 

O

 

 

 

P

 

E

F

Location

Inches

Millimeters

A

34-3/8

875

B

43-1/2

1104

C

6-1/8

157

D

3

77

E*

9-3/8

237

F*

27-3/4

706

G

40

1015

H*

24-3/4

628

Location

Inches

Millimeters

I*

8-1/4

209

J

8

203

K

12-1/8

308

L

6

154

M

46-3/4

187

N

86-3/4

2203

O

2-7/8

74

P*

7-3/8

188

*All dimensions in the front to back direction are taken from the 1/2 inch standoffs on the front face of the unit.

Figure 16.1 Appliance Dimensions

48

Heat & Glo • Bravo • 704-902Rev. E • 7/08

B. Vent Components Diagrams

 

Pipe

Effective Length

1 0 -1 /2in .

 

 

Inches

Millimeters

 

 

 

(2 67 m m )

4 5 °

E ffec tive

DVP4

4

102

H eig h t/L en g th

DVP6

6

152

 

 

 

 

 

 

DVP12

12

305

4 -7/8in .

 

 

DVP24

24

610

 

 

( 276 m m )

 

 

DVP36

36

914

 

10 -7/8 in .

D V P Pip e (se e c h a r t)

DVP48

48

1219

 

(2 7 6 m m )

 

 

 

 

 

 

 

 

DVP6A

3 to 6

76 to 152

D V P4 5 (4 5 ° E lb ow )

 

DVP12A

3 to 12

76 to 305

 

 

 

 

DVP12MI

3 to 12

76 to 305

 

 

 

DVP24MI

3 to 24

76 to 610

 

 

 

 

 

 

 

11-3 /8in .

 

 

 

 

 

(289 m m )

1 0 in .

 

 

 

 

 

(2 5 4 m m )

10 in .

 

1 in .

 

 

 

(2 5 4 m m )

 

 

 

(2 5 m m )

 

 

 

 

 

 

 

 

 

 

 

 

7-3 /8 in .

2 4 in .

 

 

 

 

(18 7 m m )

 

 

 

 

 

(610 m m )

 

 

 

 

1-1 /4in . (3 2 m m )

 

 

 

 

 

 

 

 

 

9 -1 /4in .

 

 

 

 

 

(2 35 m m )

1 /2 in . T Y P

 

 

 

 

13 -1 /4in .

(13 m m )

 

 

 

 

 

 

 

 

 

(3 37 m m )

 

D V P -AS (A ttic S h ie ld )

D V P -FS (C eilin g F iresto p )

D V P 9 0 S T (9 0 ° E lb o w )

 

 

 

 

 

 

 

 

12 in .

1 in .

 

 

 

 

(3 0 5 m m )

(25 m m )

10 in .

1- 1 /2 in .

 

 

 

8 in .

 

 

 

(2 0 3 m m )

(2 5 4 m m )

(3 8 m m )

 

14 in .

 

 

 

 

 

 

 

UP

 

 

(356 m m )

 

 

 

 

 

 

5 in .

12 in .

 

 

 

 

(12 7 m m )

(3 05 m m )

 

 

 

 

 

 

 

 

6 in .

 

 

 

 

 

(15 2 m m )

 

D V P -HV S (V e n t S u p p o r t)

 

 

 

D V P-WS (W all S h ield F iresto p )

Figure 16.2 DVP vent components

 

 

 

 

 

 

Heat & Glo • Bravo • 704-902Rev. E • 7/08

49

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than7-1/4in. (184 mm) aDVP-HSM-Bwill be required.

8 in.

(203 mm) Heat Shield

15-1/8in.

(384 mm)

EFFECTIVE LENGTH

Term Cap

Minimum

Maximum

Trap1

4-1/8in. (105 mm)

5-5/8in. (143 mm)

 

 

 

Trap2

6-3/4in. (171 mm)

10-5/8in. (270 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 in.

 

 

 

 

Max

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(305 mm)

 

Effective

 

 

 

DVP-TRAP

Length

 

 

 

 

 

 

Horizontal Termination Cap

 

 

 

DVP-TRAP1

DVP-TRAPK2

DVP-TRAP2

DVP-TRAPK1

 

Figure 16.3 DVP vent components

DVP-VTI

DVP-TH

DVP-TRAPFL

 

Flashing

 

 

 

 

 

 

 

50

Heat & Glo • Bravo • 704-902Rev. E • 7/08

 

B. Vent Components Diagrams (continued)

 

 

7-3/8in.

 

 

 

 

(187 mm)

 

 

 

 

1-1/2in.

 

 

 

 

 

(38 mm)

 

 

 

 

 

 

7-1/4in.

 

 

 

 

 

(184 mm)

12-1/2in.

 

 

 

 

 

 

 

17-3/4in.

(318 mm)

 

 

14 in.

 

 

 

 

(451 mm)

 

 

 

 

(356 mm)

5-1/4in.

 

 

 

 

 

(133 mm)

 

 

 

 

 

DVP-TVHW

 

12 in.

 

 

Vertical Term inatio n C ap (H igh w ind )

(305 mm)

 

 

 

 

 

DVP-TB1

 

 

 

 

Basement

Vent Ca

p

 

 

 

 

 

 

31 in.

DVP-HSM-B

 

 

 

 

(787 mm)

Extended Heat Shield

13-1/4in.

 

 

 

 

 

(367 mm)

 

 

24-5/8in.

 

3-7/8in.

 

 

 

(625 mm)

 

 

 

 

 

 

(98 mm)

24-5/8in.

 

27-1/2in.

 

 

 

(625 mm)

 

(127 mm)

13-1/4in.

 

10-1/2in.

 

 

 

 

 

RF6M

(367 mm)

 

(267 mm)

 

RF12M

 

DVP-TV

Roof Flashing Multi-pak

 

Roof Flashing Multi-pak

Vertical

Termination Cap

 

 

 

5 in.

11-7/8in.

5 in.

 

 

13-3/4in.

(302 mm)

(127 mm)

 

 

(349 mm)

(127 mm)

 

 

 

 

 

 

 

13-3/4in.

 

13-7/8in.

 

 

 

(352 mm)

 

 

(349 mm)

 

 

 

 

 

 

BEK

 

DVP-BEK2

 

 

 

Trap Cap Brick Extension

DVP-HPCCap Brick Extension

 

 

 

DVP and SL Series Components

 

 

13-7/8in.

9-1/2in.

 

 

 

(352 mm)

(241 mm)

11-5/8in .

 

 

 

 

 

(295 mm)

 

 

14 in.

 

 

7-1/8in.

12-1/8in.

 

 

 

(308 mm)

 

(356 mm)

 

 

(181 mm)

 

 

 

 

 

 

DRC-RADIUS

5-3/4in.

 

 

 

(146 mm)

 

 

 

 

Cap Shield

 

COOL-ADD

 

Figure 16. 4

DVP vent components

 

Cap Shield

 

 

 

 

 

 

 

Heat & Glo • Bravo • 704-902Rev. E • 7/08

 

51

B. Vent Components Diagrams (continued)

8-1/8in.

13 in.

(206 mm)

(330 mm)

15 in.

(381 mm)

DVP-HRC,DVP-HRC-SS

NOT APPROVED FOR ALL UNITS.

Effective Length

5-1/2in.

8-3/8in.

5-3/4to8-3/8in.

146 to 213 mm

140 mm

213 mm

 

87°

 

 

10-1/2in.

267 mm

10-7/8in.

276 mm

DVP-HRC-ZC,DVP-HRC-ZC-SS

NOT APPROVED FOR ALL UNITS.

Figure 16. 5 DVP Vent Components

52

Heat & Glo • Bravo • 704-902Rev. E • 7/08

C. Service Parts List

BRAVO

 

 

Service Parts Diagram

Beginning Manufacturing Date: Mar. 2002

 

Ending Manufacturing Date: ______

7

8

11

9

10

17

 

12

13

16

15

14

Log Set Assembly

1

6 43 25

Part number list on following page.

Heat & Glo • Bravo • 704-902Rev. E • 7/08

53

 

C. Service Parts List

 

 

BRAVO

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

 

 

 

Stocked

 

parts for your appliance please provide model number and serial number. All parts listed

 

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

 

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

 

 

Log Set Assembly

 

LOGS-BRAVO

Y

 

1

Log 1 Back Log

 

SRV750-703

N

 

2

Log 2 Right Inside Log

 

SRV750-705

N

 

3

Log 3 Small Log

 

SRV750-706

N

 

4

Log 4 Left Inside Log

 

SRV750-704

N

 

5

Log 5 Right Log

 

SRV704-702

N

 

6

Log 6 Left Log

 

SRV704-701

N

 

7

Non-combustibleboard

 

704-192

N

 

8

Glass Latch Assembly

 

386-122A

Y

 

 

Pilot Assembly NG (must order whole assembly)

Pre 002881385

SRV704-178-NG

Y

Î

9

Post 002881385

2090-012

Y

 

Pilot Assembly LP (must order whole assembly)

Pre 002881385

SRV704-178-LP

Y

 

 

 

 

Post 002881385

2090-013

Y

 

 

 

 

10

18” Flex 3/8” Diameter

 

567-301A

Y

 

11

Finishing Strips

 

704-233

N

 

12

Glass Retainer

 

704-235

N

 

13

Glass Door Assembly

 

GLA-BRAVO

Y

 

14

Log Grate

 

704-360A

N

 

15

Burner NG

 

704-176A

Y

 

Burner LP

 

704-175A

Y

 

 

 

 

16

Junction Box

Pre Oct 2004

100-250A

Y

 

Post Oct 2004

4031-013

Y

 

 

 

 

17

Battery Pack

 

593-594A

Y

 

 

3V Adaptor

 

593-593A

Y

 

 

Lava Rock Bag

 

705-420

N

 

 

Mineral Wool

 

050-721

N

 

 

Patch Kit

 

SRV-PACK-CFX

N

 

 

Mesh Assembly

 

MESH-BRAVO

Y

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Conversion Kit NG

 

NGKP-BRAVO

Y

 

 

Conversion Kit LP

 

LPKP-BRAVO

Y

 

 

Pilot Orifice NG

 

593-528

Y

 

 

Pilot Orifice LP

 

593-527

Y

 

 

Regulator NG

 

NGK-DXF

Y

 

 

Regulator LP

 

LPK-DXF

Y

Additional service part numbers appear on following page

54

Heat & Glo • Bravo • 704-902Rev. E • 7/08

C. Service Parts List

BRAVO

 

 

Valve Assembly Parts List

Beginning Manufacturing Date: Mar. 2002

 

Ending Manufacturing Date: ______

Intermittent Pilot Ignition

Valve Assembly

1

2

3

4

7

5

 

6

8

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

SERIAL #

PART NUMBER

 

1

Flex Ball Valve Assembly

 

302-320A

Y

2

Valve NG

 

593-500

Y

Valve LP

 

593-501

Y

 

 

3

Valve Bracket Plate

 

704-246

N

4

Wire Assembly

 

593-590A

Y

5

Module

 

593-592

Y

6

Valve Bracket

 

704-146

N

7

Jumper Wire

 

2012-206

Y

8

Wire Assembly

Pre Oct 2004

593-596A

Y

Thermostat Wire Assembly

Post Oct 2004

2045-024

Y

 

 

Orifice NG (#42A)

 

060-800

Y

 

Orifice LP (#53A)

 

060-801

Y

Heat & Glo • Bravo • 704-902Rev. E • 7/08

55

D. Limited Lifetime Warranty

LIMITED LIFETIME WARRANTY HEAT & GLO GAS APPLIANCE PRODUCTS

BASIC ONE-YEAR WARRANTY. HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEAT & GLO will replace or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reasonable labor costs incurred in replacing or repairing such components. This basic warranty is subject to the conditions, exclusions and limitations described below.

EXTENDED LIFETIME COVERAGE. HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in material or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and limitations described below.

CONDITIONS, EXCLUSIONS AND LIMITATIONS:

1.This warranty applies to the original owner only and is nontransferable.

2.This warranty applies only to Products installed in the United States of America or Canada.

3.This warranty is limited to the replacement or repair of defective components or workmanship and HEAT & GLO may fully discharge all obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if HEAT & GLO is unable to provide replacement or repair in an expedient and cost-effectivemanner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT.

4.Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under the Limited Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-YearWarranty.

5.Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this warranty unless expressly authorized and approved by HEAT & GLO in writing.

6.Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty.

7.This warranty will be void if:

a)The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the Installer’s Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.

b)Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and approved by HEAT & GLO in writing.

c)Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.

d)The Product is damaged due to shipping, improper handling, accident, abuse or misuse.

e)Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.

f ) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HEAT & GLO dealer or supplier.

NOTES TO CUSTOMER:

1.In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual servicing by an authorized HEAT & GLO dealer.

2.Please complete this information and retain this warranty in a safe place for future reference: Installation Date:______

Model #:_________________ Serial #:______________ Installing Contractor:_________________________

3.HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products.

© 2007 Hearth & Home Technologies Inc.

060-981E10/07

56

Heat & Glo • Bravo • 704-902Rev. E • 7/08

E. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

CAUTION

DO NOT DISCARD THIS MANUAL

Important operating and maintenance instructions included

Read, understand and follow these instructions for safe installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Printed in U.S.A. - Copyright 2008

Heat & Glo • Bravo • 704-902Rev. E • 7/08

57