Heat & Glo LifeStyle BE-41 User Manual

Size:
1.27 Mb
Download

Model:

Installers Guide

BE-41

 

Underwriters

Laboratories Listed

WARNING: IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

-What to do if you smell gas

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

-Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

Printed in U.S.A. Copyright 2000,

Heat-N-Glo,a division of Hearth Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044

READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS INSTALLERS GUIDE MUST BE LEFT WITH APPLIANCE FOR FUTURE REFERENCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, SERVICE AGENCY, OR THE GAS SUPPLIER.

1.This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where not prohibited by local codes.

2.This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Please contact your Heat-N-Glodealer for any questions or concerns. For the number of your nearestHeat-N-Glodealer, please call952-985-6000.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322; 4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia) 543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457;(New Zealand) 200265; or other U.S. and foreign patents pending.

394-900B9/00

1

SAFETY AND WARNING INFORMATION

!before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty.

!Prior to the first firing of the fireplace, READ the Using Your Fireplace section of theOwners Guide.

DO NOT USE this appliance if any part has been

!under water. Immediately CALL a qualified service technician to inspect the unit and to replace any part of the control system and any gas control which has been under water.

!THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a

!qualified service person. The appliance and venting system should be INSPECTED before initial use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It isIMPERATIVE that the unit’s control compartment, burners, and circulating air passagewaysBE KEPT CLEAN to provide for adequate combustion and ventilation air.

Always KEEP the appliance clear and free from

!combustible materials, gasoline, and other flammable vapors and liquids.

!NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the applianceCLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should

!be LOCATED out of traffic areas and away from furniture and draperies. Clothing or flammable materialSHOULD NOT BE PLACED on or near the appliance.

!Children and adults should be ALERTED to the hazards of high surface temperature and shouldSTAY AWAY to avoid burns or clothing ignition.

Young children should be CAREFULLY SUPERVISED when they are in the same room as the appliance.READ andUNDERSTAND all instructions carefully

These units MUST use one of the vent systems

!described in the Installing the Fireplace section of the Installers Guide.NO OTHER vent systems or componentsMAY BE USED.

This gas fireplace and vent assembly MUST be

!vented directly to the outside and MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas applianceMUST USE a separate vent system. Common vent systems are

PROHIBITED.

INSPECT the external vent cap on a regular basis to

!make sure that no debris is interfering with the air flow.

!The glass door assembly MUST be in place and sealed, and the trim door assemblyMUST be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass

!door removed, cracked, or broken. Replacement of the glass door should be performed by a licensed or qualified service person. DO NOT strike or slam the glass door.

!The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied by the gas fireplace manufacturer.NO SUBSTITUTE material may be used.

!DO NOT USE abrasive cleaners on the glass door assembly.DO NOT ATTEMPT to clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is

!recommended that a qualified service technician perform an appliance check-upat the beginning of each heating season.

!Any safety screen or guard removed for servicing must be replaced before operating this appliance.

2

TABLE OF CONTENTS

 

Safety and Warning Information ................................................

2

Service Parts Lists .....................................................................

4

Section 1: Approvals and Codes ...............................................

6

Approval Listings and Codes ........................................................

6

Appliance Certification...................................................................

6

Installation Codes ..........................................................................

6

High Altitude Installations ...............................................................

6

Section 2: Getting Started .........................................................

7

Introducing the Heat-N-GloGas Fireplaces ..................................

7

Pre-installationPreparation ...........................................................

7

Section 3: Installing the Fireplace ............................................

9

Step 1

Locating the Fireplace ...................................................

9

Step 2

Framing the Fireplace..................................................

10

Step 3

Installing the Vent System............................................

12

 

A. Vent System Approvals ...........................................

12

 

B. Installing Vent Components ....................................

18

 

C. Vent Termination ....................................................

21

Step 4

Positioning, Leveling, and

 

 

Securing the Fireplace.................................................

24

Step 5

The Gas Control Systems ...........................................

24

Step 6

The Gas Supply Line ...................................................

25

Step 7

Gas Pressure Requirements ......................................

25

Step 8

Wiring the Fireplace ....................................................

26

Step 9

Finishing ......................................................................

27

Step 10

Installing Trim, Logs, and Ember Material....................

27

 

Installing the Trim .........................................................

27

 

Positioning the Logs ....................................................

27

 

Placing the Ember Material ..........................................

30

Step 11

Before Lighting the Fireplace .......................................

30

Step 12 Lighting the Fireplace ..................................................

30

After the Installation .....................................................................

30

Section 4: Maintaining and Servicing Your Fireplace .........

31

3

Service Parts

BE-41(NG, LP) Exploded Parts Diagram / Vue éclatée des pièces

10 9

2 1 3 4

8

7

5

6 Log Set Assembly

*Part number list on following page.

*La liste des numéros de pièce se trouve à la page suivante.

4

BE-41Service Parts List / Liste des pièces de rechange

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.

ITEM /

 

 

 

STANDING PILOT AND DSI IGNITION COMMON PARTS

SERIAL # /N°

PART NUMBER

PIÈCE

 

 

 

/ UNE VEILLEUSE ET ALLUMAGE DSI PIÉCES COMMUNES

DE SÉRIE

/ N° DE PIÈCE

 

Piezo Ignitor /

Allumage Piézo

 

418-513

 

 

 

 

 

 

 

Burner Orifice NG (#38)

/

Orifice de brûleur GN (#38)

 

057-800

 

 

 

 

 

 

 

Burner Orifice LP (#51)

/

Orifice de brûleur PL (#51)

 

079-803

 

 

 

 

 

 

 

 

1

Surround

/

Entourent

 

 

 

520-130

 

 

 

 

 

 

 

2

Hood / Hotte

 

 

 

 

SRV60-143-BK

 

 

 

 

 

3

Glass Door Assembly

/ Module de Porte en verre

 

GLA-750

 

 

 

 

 

4

Burner NG / Brûleur GN

 

 

389-376A

 

 

 

 

 

 

 

4

Burner LP

/ Brûleur PL

 

 

 

389-375A

 

 

 

 

 

 

5

Log Grate

/

Grille de Bûche

 

060-361A

 

 

 

 

6

Log Set Assembly / Module de Jeu de Bûches

 

LOGS-BE41

 

 

 

 

7

Junction Box / Boîtier de raccordement

 

100-254A

 

 

 

 

 

 

8

Bottom Louver /

 

 

 

SRV394-114

 

 

 

 

 

 

 

9

Top Louver /

 

 

 

 

SRV394-249

 

 

 

 

 

STANDING PILOT IGNITION ONLY / ALLUMAGE UNE VEILLEUSE SEULEMENT

 

 

 

 

 

 

 

10

Valve Assembly NG /

Module de Valve GN

 

394-005A

 

 

 

 

 

10

Valve Assembly LP /

Module de Valve PL

 

394-006A

 

 

 

 

 

 

 

Valve NG / Valve GN

 

 

 

060-522

 

 

 

 

 

 

 

 

Valve LP

/ Valve PL

 

 

 

060-523

 

 

 

 

 

Pilot Assembly NG / Module de veilleuse GN

 

485-510A

 

 

 

 

 

Pilot Assembly LP / Module de veilleuse PL

 

485-511A

 

 

 

 

 

 

Thermocouple

/ Thermocouple

 

446-511

 

 

 

 

 

 

 

 

Thermopile

/

Thermopile

 

 

060-512

 

 

 

 

 

 

 

Pilot Tube

/

Tube de veilleuse

 

SRV485-301

 

 

 

 

 

ACCESSORIES / ACCESSOIRES

 

 

 

 

 

 

 

Conversion Kit NG / Module de conversion GN

 

NGK-BE41

 

 

 

 

 

Conversion Kit LP / Module de conversion PL

 

LPK-BE41

 

 

 

 

 

 

 

Brass Trim Kit /

 

 

 

PBK-BE41

 

 

 

 

 

 

 

 

 

5

1Approvals and Codes

Appliance Certification

The Heat-N-Glofireplace models discussed in thisInstallers Guide have been tested to certification standards and listed by the applicable laboratories.

Certification

MODEL: BE-41

LABORATORY: Underwriters Laboratories

TYPE: Direct Vent Gas Fireplace Heater

STANDARD: ANSI Z21.88•CGA2.33

High Altitude Installations

U.L. Listed gas fireplaces are tested and approved for elevations from 0 to 2,000 feet in the U.S.A. and from 0 to 4,500 feet in Canada.

When installing this fireplace at an elevation above 2,000 feet (in the United States), it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input should be reduced four percent (4%) for each 1,000 feet above sea level, unless the heating value of the gas has been reduced, in which case this general rule will not apply. To identify the proper orifice size, check with the local gas utility.

Installation Codes

The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you are in compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGA-B149Installation Codes (in Canada). The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes with the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the CSAC22.1 Canadian Electric Code (in Canada).

These models may be installed in a bedroom or bed-sittingroom in the U.S.A. and Canada.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for your location.

Heat-N-GloQuality Systems registered by SGS ICS

6

2Getting Started

Introducing the Heat-N-GloGas Fireplaces

Heat-N-Glodirect vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems. Gas fireplace diagrams, including the dimensions, are shown in this section.

Pre-installPreparation

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass.Do not install any unit with damaged, incomplete, or substitute parts.

The vent system components and trim doors are shipped in separate packages. The gas logs may be packaged separately and must be field installed.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and may present a fire hazard.

7

The Heat-N-GloWarranty will be voided by, andHeat-N-Glodisclaims any responsibility for, the following actions:

Installation of any damaged fireplace or vent system component.

Modification of the fireplace or direct vent system.

Installation other than as instructed by Heat-N-Glo.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not manufactured and approved by Heat-N-Glo,not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, it’s necessary to determine:

Where the unit is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

 

 

28 1/2 [724mm]

 

 

 

14 ¼

 

 

 

 

[362mm]

 

 

 

 

 

21 1/2 [548mm]

 

 

8 5/8 [219mm]

11 5/8 [297mm]

 

8 5/8

 

VENT COLLARS

ELECTRICAL

 

 

 

 

 

ACCESS

[219mm]

 

 

 

VENT

 

 

 

 

 

 

 

 

COLLARS

GAS LINE

 

 

 

 

ACCESS

 

 

 

 

 

38

25 ¼

34 5/8

 

 

[965mm]

[879mm]

 

 

[642mm]

 

 

 

 

24 5/8

2 1/8

 

 

3 ½

 

 

[625mm]

[55mm]

 

 

[90mm]

 

 

 

 

 

36 1/8

 

 

 

 

[916mm]

 

10 ¼

 

 

 

 

6 7/8 [174mm]

41

 

 

[259mm]

 

[1043mm]

 

 

 

 

TOP STANDOFFS

TOP VENT COLLARS

 

 

REAR VENT COLLARS

 

 

 

HOOD

 

 

 

TOP

 

 

 

LOUVER

 

 

 

LOWER

 

 

 

LOUVER

 

 

 

RATING PLATE

 

 

 

GAS

AND LABELS

 

 

 

 

ELECTRICAL

 

 

LINE

GAS

 

 

ACCESS

ACCESS

 

 

 

CONTROLS

 

 

 

Figure 1. Diagram of BE-41

 

 

 

 

8

 

 

 

3Installing the Fireplace

Step 1. Locating the Fireplace

The diagram below shows space and clearance requirements for locating a fireplace within a room.

A

 

B

C

D

E

42”

22”

36”

51”

72”

Figure 2.

Fireplace Dimensions, Locations,

 

 

and Space Requirements

 

Clearance Requirements

The top, back, and sides of the fireplace are defined by stand-offs.The minimum clearance to a perpendicular wall extending past the face of the fireplace is one inch (25 mm). The back of the fireplace may be recessed 21 1/2 inches (546 mm) into combustible construction.

Minimum Clearances

from the Fireplace to Combustible Materials

 

Inches

mm

Glass Front

........................ 36 ....................

914

Floor ...................................

0 .......................

0

Rear ...................................

1/2 .....................

13

Sides .................................

1/2 .....................

13

Top ...................................

3 1/2 ...................

89

Ceiling* ..............................

31 ....................

787

*The clearance to the ceiling is measured from the top of the unit, excluding the standoffs (see Figure 35).

The distance from the unit to combustible construction is to be measured from the unit outer wrap surface to the combustible construction, NOT from the screw heads that secure the unit together.

Minimum Clearances

from the Vent Pipe to Combustible Materials

 

Inches

mm

Vertical Sections. .............

1 ................

25

Horizontal Sections

 

 

Top .....................................

3 ................

75

Bottom ...............................

1 ................

25

Sides .................................

1 ................

25

At Wall Firestops

 

 

Top ..................................

2 1/2 ............

63.7

Bottom ..............................

1/2 ...............

13

Sides .................................

1 ................

25

For minimum clearances, see the direct vent termination clearance diagrams on pages 22 and 23 in this manual.

9

Step 2. Framing the Fireplace

Fireplace framing can be built before or after the fireplace is set in place. Framing should be positioned to accommodate wall coverings and fireplace facing material. The diagram below shows framing reference dimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING.

Shows center of 12” x 12” vent framing

SHOWS CENTER OF12" X 12" holes for top and rear venting. The center

VENT FRAMING HOLES FOR

of the hole is one (1) inch (25.4mm) above

TOP & REAR VENTING.

the center of the horizontal vent pipe.

B

C

E D

A

A.

...............

42”

B. .........

38

1/2”

C. ...............

 

22”

D. ...............

 

42”

E. .........

25

5/8”

Framing should be constructed of 2 X 4 lumber or heavier.

1/2” CLEARANCE FROM BACK OF FIREPLACE TO COMBUSTIBLE

1/2” CLEARANCE FROM BOTH SIDES OF FIREPLACE TO COMBUSTIBLE

FRAMING

MEMBER

0” CLEARANCE

0” CLEARANCE TO

FRAMING MEMBER

Figure 3. Framing Dimensions

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 7/16”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(164mm)

 

 

 

 

 

 

 

8 1/2”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(216mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 1/2”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(216mm)

 

11 1/16”

 

 

 

 

 

 

 

 

 

 

 

 

7 3/8”

 

5 7/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(281mm)

 

 

 

 

 

 

 

 

 

 

 

(187mm)

 

(149mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 1/2”

 

 

 

 

 

 

 

 

5 1/16”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(165mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(129mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 5/8”

 

 

8 5/8”

(220mm)

 

11 15/16”

(220mm)

 

 

 

 

(303mm)

DV-45D

 

DV-90D

 

 

 

 

DV-48D

 

 

 

DV-36D

 

DV17/24D

DV-12/17D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17-24

(432-610mm)

35 3/4” (908mm)

47 3/4”

(1.2m)

8 3/4”

(222mm) 5 3/4”

(146mm)

DV-06D

DV-09D

DV-12D

NOTE: PIPES OVERLAP 1-3/8INCHES (34.93mm)

AT EACH JOINT.

Figure 4. D-SeriesDirect Vent Component Specifications(5-inchinner pipe / 85/8-inchouter pipe)

11 3/4” (298mm)

11

Step 3. Installing the Vent System

A. Vent System Approvals

These models are approved to use D-seriesdirect vent pipe components and terminations (see Figures 4 and 5). Approved vent system components are labeled for identification. This pipe is tested and listed as an approved component of the fireplace. The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall. There is no required pitch for horizontal vent runs.NO OTHER VENTING SYSTEMS OR COMPONENTS MAY BE USED.

Detailed installation instructions are included with each vent termination kit and should be used in conjunction with this

Installers Guide.

The flame and ember appearance may vary based on the type of fuel burned and the venting configuration used.

Identifying Vent Components

The vent systems installed on this gas fireplace may include one, two, or three 90° elbow assemblies. The relationships of vertical rise to horizontal run in vent configurations using 90° elbows MUST BE strictly adhered to. The rise to run relationships are shown in the venting drawings and tables. Refer to the diagrams on the next several pages.

NOTE: Two 45° elbows may be used in place of one 90° elbow. Rise to run ratios in the vent system must be followed if 45° elbows are used.

This model has vent starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of starting collars will be used to attach the vent system. The starting collar sealing cap must remain on the starting collarNOT used.

 

 

VERTICAL

 

 

 

 

TERMINATION

 

STORM COLLAR

 

 

 

 

 

 

 

 

ROOF FLASHING

 

 

HORIZONTAL

 

HORIZONTAL PIPE

 

 

TERMINATION

 

 

 

 

SUPPORT

 

 

 

 

 

 

 

 

PIPE LENGTH

 

 

WALL FIRESTOP

 

 

Terminations Kits

CEILING

WALL BRACKET

 

 

 

 

 

90 DEGREE

FIRESTOP

 

 

 

 

 

 

 

 

 

ELBOW

 

 

DVK-01D

 

DVK-TVCD

 

 

DVK-01TRD

 

 

 

Figure 5.

Vent System Components and Termination Kits

 

 

 

 

12

 

 

STRAIGHT UP

VERTICAL VENTING

V (FT.)

40' MAX. (12.4 M)

Figure 6. Straight Up Vertical Venting

NOTE: On vertical venting configurations where the vertical component is over 10 feet, you may want to install the vertical baffle(VERT-BAF)(see Figure 7).

 

5” EXHAUST

 

PIPE

 

VERTICAL

 

BAFFLE

 

CENTER VERTICAL

 

BAFFLE ON 5”

 

EXHAUST PIPE

Figure 7.

Vertical Baffle

NOTE: Center the vertical baffle over the 5” exhaust pipe. Fasten in place with self tapping screws.

HORIZONTALVENTING

Kit No. H Max. Run

DVK-01D

DVK-01TRD24" (610 mm)

H

90-DEGREEELBOWS

45-DEGREE

ELBOW

NOTE: BE-41model is tested and approved to use 45° elbows in corner installations. However, 90° elbows will result in better performance.

Figure 8. Corner Installation

13

VENTING WITH ONE (1) 90° ELBOW

V

 

H

 

1' MIN. (305mm)

2'

MAX. (610mm)

2' MIN. (610mm)

4'

MAX.

(1.22m)

3' MIN. (914mm)

6'

MAX.

(1.86m)

4' MIN. (1.22m)

8'

MAX.

(2.4m)

V+H=40' MAX. (12.4m)

H = 8' MAX. (2.4m)

NOTE: On vertical venting configurations where the vertical component is over 10 feet, you may want to install the vertical baffle(VERT-BAF)improve flame appearance.

Figure 9. Venting with One 90° Elbow

VENTING WITH ONE (1) 90° ELBOW

V (FT.)

H (FT.)

1' MIN. (305mm)

5' MAX. (1.52m)

2' MIN. (610mm)

10' MAX. (3.1m)

3' MIN. (914mm)

15' MAX. (4.65m)

4' MIN. (1.22m)

20' MAX. (6.2m)

V+H= 40’ MAX. (12.4MM) H = 20' MAX. (6.2m)

H

V

 

NOTE: For corner installations: A6-inch(152mm)

 

section of straight pipe may need to be attached to

 

the fireplace before a 90o elbow, to allow the vent

 

pipe to clear the top standoffs.

 

NOTE: If a 90o elbow is first attached to the unit,

Figure 10. Venting with One 90° Elbow

the maximum horizontal run is 3-feet(914mm).

 

 

14

VENTING WITH TWO (2)

 

90° ELBOWS

 

V

H

H + H1

1´ MIN. (305 mm)

2´ MAX. (610 mm)

5´ MAX. (1.52m)

2´ MIN. (610 mm)

4´ MAX. (1.22 m)

10´ MAX. (3.1m)

3´ MIN. (914 mm)

6´ MAX. (1.86 m)

15´ MAX. (4.65m)

4´ MIN. (1.22 m)

8´ MAX. (2.48 m)

20´ MAX. (6.2m)

V+H+H1 = 40´ MAX. (12.4 m) H = 8´ MAX. (2.48 m)

H+H1 = 20´ MAX. (6.2m)

Figure 11. Venting with Two 90° Elbows

 

VENTING WITH TWO (2) 90o ELBOWS

V FT.

 

H + H1 (FT.)

1' MIN.

(305mm)

5´ MAX. (1.52m)

2' MIN.

(610mm)

10´ MAX. (3.1m)

3' MIN.

(914mm)

15´ MAX. (4.65m)

4' MIN.

(1.22m)

20´ MAX. (6.2m)

V+H+H1= 40' MAX.(12.4m)

H+H1 = 20´ MAX. (6.2m)

V+V1+H= 40' MAX.(12.4m)

 

Figure 12. Venting with Two 90° Elbows

 

 

15

VENTING WITH THREE (3) 90° ELBOWS

 

V

 

H

H + H1

1´MIN. (305mm)

2´MAX. (610mm)

5´MAX. (1.52m)

2´MIN. (610mm)

4´MAX. (1.22m)

10´MAX. (3.1m)

3´MIN. (914mm)

6´MAX. (1.86m)

15´MAX. (4.65m)

4´MIN. (1.22m)

8´MAX. (2.48m)

20´MAX. (6.2m)

V1+V+H+H1

= 40´ MAX.(12.4 m) H = 8´MAX.(2.48 m) H+H1 = 20´MAX.(6.2 m)

V

H

 

H + H1 + H2

1´MIN. (305mm)

2´MAX. (610mm)

5´MAX. (1.52m)

2´MIN. (610mm)

4´MAX. (1.22m)

10´MAX. (3.1m)

3´MIN. (914mm)

6´MAX. (1.86m)

15´MAX. (4.65m)

4´MIN. (1.22m)

8´MAX. (2.48m)

20´MAX. (6.2m)

V+H+H1+H2 = 40´ MAX. (12.4 m)

H = 8´ MAX. (2.48 m)

H+H1+H2 = 20´ MAX. (6.2 m)

Figure 13. Venting with three 90° elbows

 

 

 

16

 

 

 

 

VENTING WITH THREE (3) 90° ELBOWS

V (FT.)

H (FT.)

1' MIN. (305mm)

5' MAX. (1.52m)

2' MIN. (610mm)

10' MAX. (3.1m)

3' MIN. (914mm)

15' MAX. (4.65m)

4' MIN. (1.22m)

20' MAX. (6.2m)

NOTE: H + H1 = 20' MAX. (6.2m)

V + V1 + H + H1= 40' MAX. (12.4m)

V (FT.)

H + H1 (FT.)

1' MIN. (305mm)

5' MAX. (1.52m)

2' MIN. (610mm)

10' MAX. (3.1m)

3' MIN. (914mm)

15' MAX. (4.65m)

4' MIN. (1.22m)

20' MAX. (6.2m)

H +H1 = 20' MAX. (6.2m)

NOTE: V+V1+H +H1 = 40' MAX. (12.4m)

Figure 14. Venting with three 90° elbows

 

17

B. Installing Vent Components

After determining which set of starting collars will be used (top or rear), follow venting instructions accordingly.

Venting Out the Rear Vent

Remove the installed rear seal cap from the rear starting collars by cutting the strap at each end. (see Figure 15). Follow the vent configuration tables accordingly.

Remove the insulation from the REAR five inch flue, pull the heat shield out from outside of the firebox.

!WARNING: THE TOP HEAT SHIELD (INSIDE THE FIREBOX) MUST REMAIN ATTACHED IF THE VENT SYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE 15.

Venting Out the Top Vent

Remove the two screws in the top vent collar seal cap and remove the top vent collar seal cap and two pieces of insulation inside the top two starting collars (See Figure 15).

Remove the heat shield from inside the TOP five inch flue from outside of the firebox.

The glass must be taken off again for positioning the logs when the unit is finally installed in place and finished around it. Re-installthe glass door. Attach vent system to the top starting collars.

!WARNING: THE REAR VENT COLLAR SEAL CAP MUST REMAIN ATTACHED TO THE REAR VENT COLLARS IF THE VENT SYSTEM IS ATTACHED TO THE TOP STARTING COLLARS.

!WARNING: FAILURE TO REMOVE INSULATION IN THE SET OF COLLARS YOU ARE USING COULD CAUSE A FIRE.

!WARNING: YOU MUST LEAVE THE INSULATION IN PLACE IN THE SET OF COLLARS YOU ARE NOT USING.

If your vertical vent component is over 10 feet, you may want to install the vertical baffle (located in the bag containing the install manual) to improve flame appearance. Center the vertical baffle on the 5” flue being used, and with self tapping screws secure the baffle to the inside of the firebox.

Venting Out Rear

Venting Out Top

SEAL

SEAL

 

CAP

CAP

 

HEAT

INSULATION

 

SHIELD

 

 

DISCARD BOTH

 

 

PIECES and

 

 

HEAT SHIELD

HEAT

DISCARD

 

SHIELD

INSULATION

 

 

and

 

 

HEAT SHIELD

 

 

Insert screwdriver

 

 

or similar object

 

 

here to remove cap.

CUT

 

 

 

 

HERE

Figure 15

 

 

1. Attach the First Vent Component to the Starting Collars

To attach the first vent component to the starting collars of the fireplace:

Apply a 3/8 inch (9.5mm) bead of stove cement around the 5 inch (127mm) fireplace starting collar.

Make sure that the fiberglass rope gasket supplied with the fireplace seals between the first 8-5/8inch (219mm) vent component and the outer fireplace wrap.

Lock the vent components into place by sliding the concentric pipe sections with four (4) equally spaced interior beads into the fireplace collar or previously installed component end with four (4) equally spaced indented sections.

When the internal beads of each 8-5/8inch (219mm) outer pipe line up, rotate the pipe section clockwise aboutone-quarter(1/4) turn. The vent pipe is now locked together.

The first 90° elbow installed in the vent system of a rear venting fireplace MUST BE in a vertical position.

STARTING

COLLAR

STOVE

SEALANT

BEAD

FIRST VENT

COMPONENT

1 INCH (25.4mm)

Figure 16. Attaching the First Vent Component to the Starting Collars

!WARNING: A 3/8 INCH (9.5 MM) BEAD OF STOVE CEMENT MUST BE PLACED AROUND

THE 5 INCH (127 MM) FIREPLACE STARTING COLLAR BEFORE ATTACHING THE FIRST VENT COMPONENT. FAILURE TO SEAL THIS JOINT MAY CAUSETHEFIREPLACETOOPERATEIMPROPERLY.

!WARNING: ENSURE THAT THE FIBERGLASS ROPE GASKET SUPPLIED WITH THE

FIREPLACE SEALS BETWEEN THE FIRST VENT COMPONENTAND THE OUTER FIREPLACE WRAP.

If the installation is for a termination cap attached directly to the fireplace, skip to the sections, Install Firestops and

Vent Termination.

18

2.Continue Adding Vent Components

Continue adding vent components, locking each succeeding component into place.

Ensure that each succeeding vent component is securely fitted and locked into the preceding component in the vent system.

90° elbows may be installed and rotated to any point around the preceding component’s vertical axis. If an elbow does not end up in a locked position with the preceding component, attach with a minimum of two (2) sheet metal screws.

Figure 17. Adding Venting Components

3. Install Support Brackets

For Horizontal Runs - The vent system must be supported every five (5) feet of horizontal run by a horizontal pipe support.

To install support brackets for horizontal runs:

Place the pipe supports around the vent pipe.

Nail the pipe supports to the framing members.

For Vertical Runs - The vent system must be supported every eight (8) feet (2.4m) above the fireplace flue outlet by wall brackets.

To install support brackets for vertical runs:

Attach wall brackets to the vent pipe and secure the wall bracket to the framing members with nails or screws.

WALL BRACKET

WALL STUD

8 FT. (2.4m)

FLUE

OUTLET

1 INCH MIN. (25.4mm)

Figure 18. Installing Support Brackets

4. Install Firestops

For Horizontal Runs - Firestops are REQUIREDon both sides of a combustible wall through which the vent passes.

NOTE: Model DVK-01TRDdoes not need an exterior firestop on an exterior combustible wall.

To install firestops for horizontal runs that pass through either interior or exterior walls:

Cut a 12-inchby12-inch(305mm X 305mm) hole through the wall.

NOTE: The center of the hole is one (1) inch (25.4mm) above the center of the horizontal vent pipe.

19

Position the firestops on both sides of the hole previously cut and secure the firestops with nails or screws.

The heat shields of the firestops MUST BE placed towards the top of the hole.

Continue the vent run through the firestops.

12"

(305mm)

12"

(305mm)

1" (25.4 mm)

VENT PIPE

Figure 19. 12" x 12" Hole and Vent Pipe

HEAT SHIELD

TRIM HEAT SHIELD IF TOO LONG, ADD TO SHIELD IF TOO SHORT

EXTERIOR

FIRESTOP

INTERIOR

FIRESTOP

Figure 20. Heat Shield, Interior & Exterior Firestops

For Vertical Runs - One ceiling firestop is REQUIREDat the hole in each ceiling through which the vent passes.

To install firestops for vertical runs that pass through ceilings:

Position a plumb bob directly over the center of the vertical vent component.

Mark the ceiling to establish the centerpoint of the vent.

Drill a hole or drive a nail through this centerpoint.

Check the floor above for any obstructions, such as wiring or plumbing runs.

Reposition the fireplace and vent system, if necessary, to accommodate the ceiling joists and/or obstructions.

Cut an 11-inchX11-inch(280mm X 280mm) hole through the ceiling, using the centerpoint previously marked.

Frame the hole with framing lumber the same size as the ceiling joists.

11" (280 mm)

11" (280mm)

 

 

CHIMNEY

 

HOLE

NEW

EXISTING CEILING

JOISTS

FRAMING

 

MEMBERS

 

CEILING

 

Figure 21. 11" x 11" Hole & New Framing Members

20

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

Figure 22. Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm).

 

NAILS (4 REQUIRED)

 

RAFTER

CEILING

 

 

CEILING FIRESTOP

Figure 23.

Attic Firestop

C. Vent Termination

For Horizontal Terminations - To attach and secure the termination to the last section of horizontal vent:

Rotate and interlock the ends as described at the beginning of the Installing Vent Components section.

The termination kit should pass through the wall firestops from the exterior of the building.

Adjust the termination cap to its final exterior position on the building.

!WARNING: THETERMINATIONCAPMUSTBEPOSITIONEDSOTHATTHEARROWISPOINTINGUP.

For roundcap termination kits:

Use the exterior pipelock hole on the round flange of the wall firestop to secure the vent pipe in place.

For trapezoidal cap termination kits:

Using screws secure the cap to the exterior wall through the flanges in the cap.

!WARNING: THE BOTTOM OF THE VENT TERMINATION CAP MUST BE A MINIMUM

OF 12 INCHES (305 MM) ABOVE GROUND LEVEL (GRADE). THE TOP OF THE CAP MUST BE A MINIMUM OF 18 INCHES (457 MM) BELOW COMBUSTIBLE MATERIAL, SUCH AS A DECK. THE SIDE OF THE CAP MUST BE A MINIMUM OF 6 INCHES (152 MM) AWAY FROM A PARALLEL OUTSIDE WALL. VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL OR SIDING. SEE THE FOLLOWING DIAGRAM FOR VENT TERMINATION CLEARANCES.

ROUND CAP TERMINATION

PERFORATION CANNOT BE

INSIDE THE WALL

7 1/2" (191mm) MINIMUM

TRAPEZOID CAP TERMINATION

7 1/4" (184mm)

Figure 24. Round & Trapezoid Termination Caps

21

 

 

G

 

 

 

 

 

v

 

 

 

D

 

A

H

 

 

 

 

 

 

 

E

 

 

 

 

 

v

 

 

 

 

 

L

C

openable fixed closed

 

 

 

v B

 

 

 

v

 

 

 

 

 

v

 

 

 

 

 

 

 

 

 

F v

B

 

M

 

 

v

I

 

 

B

B

v

X

 

 

 

 

 

 

 

 

A

 

 

J or K

234

V =VENT TERMINALX =AIR SUPPLY INLET234234 =AREA WHERE TERMINAL IS NOT PERMITTED

234

A

= 12" ....................

clearances above grade, veran-

 

 

da, porch, deck or balcony

B= 12" .................... clearances to window or door

that may be opened

C= 9" (U.S.A.)

 

 

12" (Canada) .....

clearance to permanently

 

 

 

closed window.

*D

=

18" ....................

vertical clearance to ventilated

 

 

 

soffit located above the termi-

 

 

 

nal within a horizontal distance

 

 

 

of 2 feet (60 cm) from the cen-

 

 

 

ter-lineof the terminal

*E

=

18" ....................

clearance to unventilated soffit

F

=

9" .....................

clearance to outside corner

G

=

6" ......................

clearance to inside corner

H

=

3 ft. (Canada) ....

not to be installed above a gas

 

 

 

meter/regulator assembly with-

in 3 feet (90cm) horizontally from the center-lineof the regulator

I= 3 ft. (U.S.A.)

6 ft. (Canada) ..... clearance to service regulator vent outlet.

J= 9" (U.S.A.)

12" (Canada) ..... clearance to non-mechan-ical air supply inlet to building or the combustion air inlet to any other appliance

K

=

3 ft. (U.S.A.)

 

 

 

6 ft. (Canada) .....

clearance to a mechanical

 

 

 

air supply inlet

**L

=

7 ft. ...................

clearance above paved

 

 

 

sidewalk or a paved drive-

 

 

 

way located on public

 

 

 

property

***M =

18" ....................

clearance under veranda,

 

 

 

porch, deck or balcony

*30” minimum for vinyl clad soffits.

**a vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

*** only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor.

NOTE: Local codes or regulations may require different clearances.

Figure 25. Vent Termination Minimum Clearances

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS NECESSARY TO INSTALL THE VINYL PROTECTOR KIT TO THE TOP OF THE EXTERIOR FIRESTOP (FOR ALL ROUND TERMINATION CAPS).

22

For Vertical Terminations - To locate the vent and install the vent sections:

Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint.

Make the outline of the roof hole around the centerpoint nail.

The size of the roof hole framing dimensions depend on the pitch of the roof. There MUST BE a1-inch(25.4mm) clearance from the vertical vent pipe to combustible materials.

Mark the roof hole accordingly.

Cover the opening of the installed vent pipes.

Cut and frame the roof hole.

Use framing lumber the same size as the roof rafters and install the frame securely. Flashing anchored to the frame must withstand heavy winds.

Continue to install concentric vent sections up through the roof hole (for inside vent installations) or up past the roof line until you reach the appropriate distance above the roof (for outside terminations).

!WARNING: MAJOR U.S. BUILDING CODES SPECIFY MINIMUM CHIMNEY AND/OR

VENT HEIGHTABOVE THE ROOF TOP. THESE MINIMUM HEIGHTS ARE NECESSARY IN THE INTEREST OF SAFETY. SEE THE FOLLOWING DIAGRAM FOR MINIMUM HEIGHTS, PROVIDED THE TERMINATION CAP IS AT LEAST TWO (2) FEET FROM A VERTICAL WALLAND 2-FEETBELOW A HORIZONTAL OVERHANG.

NOTE: This also pertains to vertical vent systems installed on the outside of the building.

To seal the roof hole, and to divert rain and snow from the vent system:

Attach a flashing to the roof using nails, and use a nonhardening mastic around the edges of the flashing base where it meets the roof.

Attach a storm collar over the flashing joint to form a water-tightseal. Placenon-hardeningmastic around the joint, between the storm collar and the vertical pipe.

Slide the termination cap over the end of the vent pipe and rotate the pipe clockwise 1/4 turn.

HORIZONTAL

OVERHANG

2 FT.

2 FT. MIN.

VERTICAL

MIN.

 

 

WALL

 

 

LOWEST

DISCHARGE

OPENING

TERMINATION

CAP

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (min.) ft.

flat to 6/12

1.0

6/12 to 7/12

1.25

over 7/12 to 8/12

1.5

over 8/12 to 9/12

2.0

over 9/12 to 10/12

2.5

over 10/12 to 11/12

3.25

over 11/12 to 12/12

4.0

over 12/12 to 14/12

5.0

over 14/12 to 16/12

6.0

over 16/12 to 18/12

7.0

over 18/12 to 20/12

7.5

over 20/12 to 21/12

8.0

Figure 26. Minimum Height from Roof to Lowest Discharge Opening

23

Step 4. Positioning, Leveling, and

Securing the Fireplace

The diagram below shows how to properly position, level, and secure the fireplace.

Figure 27. Proper Positioning,

Leveling and Securing of a Fireplace

Place the fireplace into position.

Level the fireplace from side to side and front to back.

Shim the fireplace with non-combustiblematerial, such as sheet metal, as necessary.

Secure the fireplace to the framing by nailing or screwing.

Step 5. The Gas Control Systems

!WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

The type of gas control system used with this model is:

Standing Pilot Ignition.

Standing Pilot Ignition System

This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor.

!WARNING: 110-120VAC MUST NEVER BE CONNECTED TO A CONTROL VALVE IN A MILLIVOLT SYSTEM.

Figure 28.

Gas Controls Systems

24

Step 6. The Gas Supply Line

NOTE: Have the gas supply line installed in accordance with local building codes by a qualified installer approved and/or licensed as required by the locality.

NOTE: Before the first firing of the fireplace, the gas supply line should be purged of any trapped air.

NOTE: Consult local building codes to properly size the gas supply line leading to the 1/2 inch (13mm) hook-upat the unit.

This gas fireplace is designed to accept a 1/2 inch (13 mm) gas supply line.To install the gas supply line:

A listed (and State of Massachussetts approved) 1/2 inch (13mm) tee-handlemanualshut-offvalve and a listed flexible gas connector are connected to the 1/2 inch (13mm) inlet of the control valve.NOTE: If substituting for these components, please consult local codes for compliance.

Locate the gas line access hole in the outer casing of the fireplace.

The gas line may be run from either side of the fireplace provided the hole in the outer wrap does not exceed 2 1/2” in diameter and it does not penetrate the actual firebox.

The gap between the supply piping and gas access hole can be plugged with non-combustibleinsulation to prevent cold air infiltration.

Open the fireplace lower grille, insert the gas supply line through the gas line hole, and connect it to the shut-offvalve.

When attaching the pipe, support the control so that the lines are not bent or torn.

After the gas line installation is complete, use a soap solution to carefully check all gas connections for leaks.

!WARNING: DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

At the gas line access hole, use insulation to re-packthe space around the gas pipe.

Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing.

Use a wrench on shut-offvalve when tightening gas line.

MANUAL

SHUT-OFF

VALVE

GAS

VALVE

CONTROL

VALVE

FLEX

GAS LINE CONNECTOR

ACCESS HOLE

Figure 29. Gas Supply Line

Step 7. Gas Pressure Requirements

Pressure requirements for Heat-N-Glogas fireplaces are shown in the table below.

Pressure

Natural Gas

Propane

Minimum

5.0 inches

11.0 inches

Inlet Pressure

w.c.

w.c.

Maximum Inlet

14.0 inches

14.0 inches

Gas Pressure

w.c.

w.c.

Manifold

3.5 inches

10.0 inches

Pressure

w.c.

w.c.

 

 

 

A one-eighth(1/8) inch (3 mm) N.P.T. plugged tapping is provided on the inlet and outlet side of the gas control for a test gauge connection to measure the manifold pressure. Use a small flat blade screwdriver to crack open the screw in the center of the tap. Position a rubber hose over the tap to obtain the pressure reading.

The fireplace and its individual shut-offvalve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess ofone-half(1/2) psig (3.5 kPa).

The fireplace must be isolated from the gas supply piping system by closing its individual shut-offvalve during any pressure testing of the gas supply piping system at test pressures equal to or less thanone-half(1/2) psig (3.5 kPa).

25

TH

TP

TP

TH

GAS VALVE

BLACK S2

WHITE T2

RED T1

THERMOPILE

OPTIONAL REMOTE

OPTIONAL WALL SWITCH

BLACK S1

Figure 30. Standing Pilot Ignition Wiring Diagram

Step 8. Wiring the Fireplace

NOTE: Electrical wiring must be installed by a licensed electrician.

CAUTION: DISCONNECT REMOTE CONTROLS IF ABSENT FOR EXTENDED TIME PERIODS. THIS WILL PREVENT ACCIDENTAL FIREPLACE OPERATION.

For Standing Pilot Ignition Wiring

Appliance Requirements

This appliance DOES NOT require110-120VAC to operate.

!WARNING: DO NOT CONNECT 110-120VAC TO THE GAS CONTROL VALVE OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Optional Accessories

Optional fan and remote control kits require that 110-120VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Remote Wall Switch

Position the remote wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/ OFF switch pigtails.

WARNING: DO NOT CONNECT 110-120VAC! TO THE REMOTE WALL SWITCH OR THE

CONTROL VALVE WILL BE DESTROYED.

CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPERAND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.

VARIABLE SPEED CONTROL

BLK

BLK

JUNCTION BOX

BLK

BLK

BLK

BLK

BLK

WHT WHT

BLK

GROUND

TEMPERATURE

SENSOR SWITCH

NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE

REPLACED WITH TYPE 105OC RATED WIRE.

BLOWER RECEPTACLE

BLOWER

 

GRN

JUNCTION BOX

TEMPERATURE

BLK

SENSOR SWITCH

WHT

 

110-120VAC

FAN

Figure 31. Fan Wiring Diagram

SPEED CONTROL (RHEOSTAT)

26

Step 9. Finishing

Figure 35 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 2 and 3 for other fireplace clearances.

Only non-combustiblematerials may be used to cover the black fireplace front.

!WARNING: WHEN FINISHING THE FIREPLACE, NEVER OBSTRUCT OR MODIFY THE AIR INLET/OUTLET GRILLES IN ANY MANNER.

 

 

 

 

 

 

 

CEILING

 

 

 

 

12"

 

 

 

 

 

 

11"

 

 

 

 

 

 

10"

 

 

 

 

 

9"

 

 

 

31”

 

 

8"

 

 

 

 

 

 

7"

 

 

 

 

 

 

 

6"

 

 

 

 

12”

 

 

5"

 

 

 

 

11”

 

4"

 

 

 

 

 

10”

2" 3"

 

 

 

 

8”

9”

 

 

5”

6”

7”

1”

 

4"

 

 

 

 

 

2”

3”

 

 

 

 

 

1”

 

 

 

 

 

 

TOP FRONT EDGE

OF FIREPLACE

Figure 32.

Minimum Vertical and Maximum Horizontal Dimensions of Combustibles above Fireplace

CAUTION: IF JOINTS BETWEEN THE FINISHED WALLS AND THE FIREPLACE SURROUND (TOP AND SIDES) ARE SEALED, A 300° F. MINIMUM SEALANT MATERIAL MUST BE USED. THESE JOINTS ARE NOT REQUIRED TO BE SEALED. ONLY NON-COMBUSTIBLEMATERIAL (USING 300° F. MINIMUM ADHESIVE, IF NEEDED) CAN BE APPLIED AS FACING TO THE FIREPLACE SURROUND. SEE THE DIAGRAM BELOW.

FINISH WALL MATERIAL MAY BE DRYWALL

 

- TOP AND SIDES

 

0

0

0

HIGH TEMPERATURE (300O F/149O C MIN.)

 

TOP & SIDE SEAL JOINT

Figure 33.

Sealant Material

Hearth Extensions

A hearth extension may be desirable for aesthetic reasons. However,ANSI or CAN/CGAtesting standards do not require hearth extensions for gas fireplace appliances.

Step 10. Installing Trim, Logs,

and Ember Material

Installing the Trim

Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall and the fireplace top and sides can only be sealed with a 300° F. (149° C) minimum sealant.

WARNING: WHEN FINISHING THE FIREPLACE,

!NEVER OBSTRUCT OR MODIFY THE AIR INLET/ OUTLET GRILLES IN ANY MANNER.

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other non-combustiblematerials can be used to cover up the gap between the sheet rock and the fireplace.

Do not obstruct or modify the air inlet/outlet grilles. When overlapping on both sides, leave enough space so that the bottom grille can be lowered and the trim door removed.

27

Positioning the Logs

! BEFORE

FIRING THE UNIT

Follow these steps:

1.Release four glass clips and set the glass assembly aside.

CAUTION: The log assembly is fragile. Handle with care.

NOTE: See Step 9 when replacing the log set in an existing fireplace.

Figure 34

2.Carefully cut the cable tie holding the log assembly in place and discard the tie. Do not leave any part of the tie in the fireplace (see Figure 35).

!WARNING: USE WIRE CUTTERS. DO NOT ATTEMPT TO CUT THE TIE WITH A KNIFE.

3.Grasp the log assembly by the ends. Do NOT grasp the log assembly by the center.Remove the log assembly from the fireplace and set aside.

4.Remove the foam pad from the fireplace and discard. Make sure all pieces of the foam are removed. With a screwdriver bend up the log placement tabs (see Figure 36).

Figure 35

Log Placement Tabs

Figure 36

28

5.The grate is located in the lower cavity. Remove the screw holding the grate in place and discard the screw.

6.Position the grate into the cutout in the refractory. Hook the grate into position using the tabs on the bottom of the grate. Make sure the grate is pulled forward on the refractory (see Figure 37).

7.Cut shrink wrap and remove from around the log assembly.

!WARNING: REMOVE ALL PACKAGING FROM LOGS.

8.Install embers. See ember placement instructions for details.

!WARNING: USE DIME SIZE PIECES ONLY. DO NOT COVER PORTS.

9.Carefully position the log set in place into the fireplace. Pull the log set forward until the log set contacts the log placement tabs. Center the log set in the firebox side to side (see Figure 38). (Grate removed for viewing.)

Figure 37

Log Placement Tabs

Figure 38

29

Placing the Ember Material

Ember material is shipped with this gas fireplace. The bag labeled Glowing Ember (050-721)is standard glowing ember material. To place the ember material:

Pull the four glass latches out of the groove on the glass frame. Remove glass door from the unit (see Figure 39).

Place dime size pieces of Glowing Ember (050-721)ember material about 1/2 inch apart near port holes in burner top. Do NOT press embers into burner ports. Cover the top of the burner with a single layer of ember material. For best performance do NOT place embers on the ports at the rear of the burner.

Save the remaining ember materials for use during fireplace servicing.

Replace the glass door and a front trim door on the unit.

Pull out and latch the glass clips into the groove on the glass frame.

Figure 39. Glass Assembly

Glass Specifications:

 

BE-41:

24 1/2 X 35 1/2

TEMPERED

Figure 40. Placement of the Ember Material

CAUTION: IT IS STRONGLY RECOMMENDED THAT TRIM DOORS WITH OPTIONAL MESH SCREENS BE INSTALLED ON PROPANE MODELS.

Step 11. Before Lighting the Fireplace

Before lighting the fireplace, be sure to do the following:

Remove all paperwork from underneath the fireplace. Review safety warnings and cautions

Read the Safety and Warning Informationsection at the beginning of this Installers Guide.

Double-checkfor gas leaks

Before lighting the fireplace, double-checkthe unit for possible gas leaks.

Double-checkvent terminations and front grilles for obstructions.

Before lighting the fireplace, double-checkthe unit for possible obstructions that could be blocking the vent terminations or the front grilles.

Double-checkfor faulty components

Any component that is found to be faulty MUST BE replaced with an approved component. ampering with the fireplace components isDANGEROUS and voids all warranties.

A small amount of air will be in the gas supply lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and will operate normally.

Subsequent lightings of the fireplace will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

NOTE: The fireplace should be run for 8 hours on the initialstart-up.This will help to cure the chemicals used in the paint and logs.

Step 12. Lighting the Fireplace

You’ve reviewed all safety warnings, you’ve checked the fireplace for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the fireplace.

!WARNING: PLEASE REFER TO THE USER’S MANUAL FOR ALL CAUTIONS, SAFETY, AND

WARNING INFORMATION PERTAINING TO THE LIGHTING AND OPERATION OF THE FIREPLACE.

After the Installation

!LEAVE THIS INSTALLATION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.

30

4Maintaining and Servicing Your Fireplace

Fireplace Maintenance

Although the frequency of your fireplace servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance check-upat the beginning of each heating season. See the table below for specific guidelines regarding each fireplace maintenance task.

IMPORTANT: TURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE.

Replacing old ember material

Frequency: Once annually, during the checkup.By: Qualified service technician.

Task: Brush away loose ember material near the burner. Replace old ember material with newdime-sizeand shape pieces of Golden Ember(DE-93)and Glowing Ember (050721). New ember material should be placed alternately on top of the burner - a layer of Golden Ember, a layer of Glowing Ember, and so on. Save the remaining ember material and repeat this procedure at your next servicing. For more information, seePlacing Ember Material.

Cleaning Burner and Controls Frequency:Once annually. By:Qualified service technician.

Task: Brush or vacuum the control compartment, fireplace logs and burner areas surrounding the logs.

Checking Flame Patterns, Flame Height

Frequency: Periodically.

By: Qualified service technician/Home owner.

Task: Make a visual check of your fireplace’s flame patterns. Make sure the flames are steady - not lifting or floating. See Figure 41. The flame sensor (DSI) or thermopile/ thermocouple (standing pilot) tips should be covered with flame. See Figure 28.

Checking Vent System

Frequency: Before initial use and at least annually thereafter, more frequently if possible.

By: Qualified service technician/Home owner.

Task: Inspect the external vent cap on a regular basis to ensure that no debris is interfering with the flow of air. Inspect entire vent system for proper function.

Cleaning Glass Door Frequency:As necessary By:Home owner.

Task: Clean as necessary, particularly after adding new ember (flame colorant) material. Film deposits on the inside of the glass door should be cleaned off using a household glass cleaner.NOTE: DO NOT handle or attempt to clean the door when it is hot and DO NOT use abrasive cleaners.

MAKE SURE THE FLAMES

ARE STEADY—NOT

LIFTING OR FLOATING.

Figure 41.

Burner Flame Patterns

31