Heat & Glo LifeStyle BAY-40 User Manual

Size:
2.7 Mb
Download

¨

Owner’s Manual

 

Installation and Operation

Models:

BAY-40,PIER-40

Multi-sided

Woodburning Fireplace

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating •

Read, understand

• Leave this manual with

a n d m a i n t e n a n c e

and follow these

party responsible for

instructions included.

instructions for safe

use and operation.

 

i n s t a l l a t i o n a n d

 

 

operation.

 

DO DISCARDNOT

WARNING

¨

WARNING

 

If the information in these instructions is not followed exactly, a fire may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Do not overfire. Overfiring will void your warranty.

Comply with all minimum clearances to combustibles as specified. Failure to comply may cause house fire.

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

Do not touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Installation and service of this fireplace should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory-trainedprofessionals, or technicians supervised by an NFI certified professional.

Keep clothing, furniture, draperies and other flammable materials away.

WARNING

Fire Risk

For use with solid wood fuel or decorative gas appliance only.

Do not install unvented gas logs.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

1

Read this manual before installing or operating this fireplace. Please retain this owner’s manual for future reference.

Congratulations!

Congratulations on selecting a Heat & Glo wood burning fireplace. The Heat & Glo fireplace you have selected is designed to provide the utmost in safety, reliability and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest you keep it with your other important documents and product manuals.

The information contained in this owner’s manual unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo wood burning fireplace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fireplace products!

 

Homeowner Reference Information

We recommend that you record the following pertinent

 

 

 

 

 

 

 

information about your fireplace:

 

 

Model Name:

 

 

Date purchased/installed:

 

 

 

Serial Number:

 

 

Location on fireplace:

 

 

 

Dealership purchased from:

 

 

Dealer phone:

 

 

 

Notes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Listing Label Information/Location

The model information regarding your specific fireplace can be found on the rating plate located on the smoke shield of the fireplace.

Serial

Grate

Fireplace

Number

Model

 

FIREPLACE NO.

FIRE DAMAGE. REPLACE MODEL NO.

MODEL NO.

MFG. DATE

 

WARNING: RISK OF

 

 

 

GRATE WITH HEARTH & HOME

 

 

 

TECHNOLOGIES INC.

 

 

FIRECHAMBER INTENDED FOR USE WITH HEARTH & HOME TECHNOLOGIES INC. LISTED FIREPLACE PARTS. SEE INSTALLATION AND OPERATING INSTRUCTIONS FOR THIS MODEL. ONLY HEARTH & HOME TECHNOLOGIES INC. GLASS DOOR KITS CAN BE INSTALLED ON THIS UNIT.

FIREPLACE ALSO FOR USE

YES

 

NO

 

 

 

 

 

CLEARANCE TO

CHIMNEY

FIREBOX

 

 

IN.

 

IN MANUFACTURED HOMES

 

 

 

 

 

 

COMBUSTIBLES:

2 IN. MIN.

 

 

MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FAN KIT

 

 

 

&

 

 

 

 

 

RATED AT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MODEL NO.

 

 

 

 

 

 

 

 

115 VOLTS, 50/60 Hz.,

 

 

 

AMP.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DO NOT OVERFIRE. USE ONLY: SOLID WOOD FUEL OR

 

WARNING! THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED

 

 

 

LISTED DECORATIVE GAS APPLIANCE. DO NOT USE A

 

GAS LOG SET. TO REDUCE THE RISK OF FIRE OR INJURY, DO NOT

 

FIREPLACE INSERT OR OTHER PRODUCTS NOT

 

INSTALL AN UNVENTED GAS LOG SET INTO FIREPLACE.

 

SPECIFIED FOR USE WITH THIS PRODUCT. IF DOORS

 

WARNING! THIS APPLIANCE IS NOT FOR USE AS COOKING EQUIPMENT.

 

ARE USED OPERATE FIREPLACE WITH DOORS FULLY

 

 

 

 

 

 

 

 

 

 

 

 

 

OPEN OR CLOSED ONLY. WHEN BURNING A

 

 

 

 

 

IF INSTALLATION OR OPERATING INSTRUCTIONS ARE MISSING

 

DECORATIVE GAS APPLIANCE IN THE FIREPLACE,

 

 

 

CONTACT: HEARTH & HOME TECHNOLOGIES INC.,

 

 

 

ADJUST DAMPER TO THE FULLY OPEN POSITION.

 

 

 

 

 

1915 W. SAUNDERS ST., MT. PLEASANT, IA 52641.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

Table of Contents

1 Listing and Code Approvals

4

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Getting Started

5

A. Design and Installation Considerations . . . . . . . . . . . . 5

B. Negative Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

C. Typical Fireplace System. . . . . . . . . . . . . . . . . . . . . . . 7

D. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . 8

E. Inspect Fireplace and Components . . . . . . . . . . . . . . . 8

3 Framing and Clearances

9

A. Selecting Fireplace Location . . . . . . . . . . . . . . . . . . . . 9

B. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

C. Sidewalls/Surrounds . . . . . . . . . . . . . . . . . . . . . . . . . 11

E. Construct the Chase . . . . . . . . . . . . . . . . . . . . . . . . . 12

F. Chimney Requirements . . . . . . . . . . . . . . . . . . . . . . . 12

4 Installation of Fireplace

13

A. Install the Outside Air Kit . . . . . . . . . . . . . . . . . . . . . . 13

5 Chimney Assembly

16

A. Chimney Requirements . . . . . . . . . . . . . . . . . . . . . . . 17

B. Using Offsets/Returns . . . . . . . . . . . . . . . . . . . . . . . . 18

C. Assemble the Chimney Sections . . . . . . . . . . . . . . . . 19

D. Install the Ceiling Firestops . . . . . . . . . . . . . . . . . . . . 19

E. Install the Attic Insulation Shield . . . . . . . . . . . . . . . . 20

F. Double-checkthe Chimney Assembly . . . . . . . . . . . . 21

G. Secure the Chimney . . . . . . . . . . . . . . . . . . . . . . . . . 21

6 Complete the Enclosure

22

A. Chimney Termination . . . . . . . . . . . . . . . . . . . . . . . . . 22

B. Chase Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

C. Install the Termination Cap . . . . . . . . . . . . . . . . . . . . 24

7 Accessories

26

A. Gas Log/Lighter Provisions . . . . . . . . . . . . . . . . . . . . 26

8 Finishing

27

A. Hearth Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

B. Finishing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

C. Mantel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

D. Sidewalls/Surrounds . . . . . . . . . . . . . . . . . . . . . . . . . 29

E. Glass Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9 Operating Instructions

30

A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . 30

B. Outside Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

C. Clear Space Near the Fireplace. . . . . . . . . . . . . . . . . 31

D. Flue Damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

E. Firescreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

F. Glass Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

G. Grate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

H. Wood Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

I. Starting a Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

10 Troubleshooting

34

A. Understanding Vent Problems . . . . . . . . . . . . . . . . . . 34

B. Diagnostics and Problem Solving . . . . . . . . . . . . . . . 35

11 Maintenance and Servicing the Fireplace 37

A. Disposal of Ashes . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

B. Chimney Inspection/Cleaning . . . . . . . . . . . . . . . . . . 37

C. Firebox Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

D. Maintenance Task List . . . . . . . . . . . . . . . . . . . . . . . . 38

E. Chimney Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

12 Reference Materials

39

A. Fireplace Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 39

B. Fireplace Components. . . . . . . . . . . . . . . . . . . . . . . . 40

C. Chimney Components . . . . . . . . . . . . . . . . . . . . . . . . 41

D. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

E. Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

F. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Note: An arrow (¨) found in the text signifies change in content.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

3

1

Listing and Code Approvals

 

 

 

 

 

A. Appliance Certification

 

 

WARNING

 

This fireplace system has been tested and listed in accor-

 

dance with UL 127 standards by Underwriters Laboratories

 

 

Improper installation, adjustment, alteration, service

 

Inc. for installation and operation in the United States.

 

or maintenance can cause injury or property damage.

 

This fireplace has been tested and listed for use with the

Refer to the owner’s information manual provided with

 

optional components specified in this manual. Glass doors

this fireplace. For assistance or additional information

 

consult a qualified installer, service agency or your

 

are required. Optional components may be purchased sep-

 

dealer.

 

arately and installed at a later date. Installation of an outside

 

 

 

air kit will require significant reconstruction and is best if in-

 

 

stalled at the time of fireplace installation.

 

 

Heat & Glo is a registered trademark of Hearth & Home Technologies Inc.

Not intended for use as a primary heat source.

This fireplace is tested and approved as a decorative fireplace. It should not be factored as a primary heat source in residential heating calculations.

WARNING

Fire Risk

Do not install or operate damaged fireplace.

Do not modify fireplace.

Installation other than as instructed by Hearth & Home Technologies Inc. is strictly prohibited.

Do not operate the fireplace without fully assembling all components.

Do not overfire.

Do not install an unvented gas log set. This fireplace has not been tested for use with unvented gas log sets.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the above actions.

4

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

2 Getting Started

A. Design and Installation Considerations

CAUTION

Check building codes prior to installation.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction about restrictions, installation inspection and permits.

When planning a fireplace installation, it is necessary to determine the following information before installing:

Where the fireplace is to be installed. See Sections 3 and 4.

The vent system configuration to be used. See Sections 5 and 6.

Gas supply piping. See Section 7.

Electrical wiring. See Section 7.

Framing and finishing details. See Sections 3, 6 and 8.

Whether optional accessories—devicessuch as a fan, wall switch or remotecontrol—aredesired. See Section 12.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

Preventing negative pressure

Location of fireplace and chimney

WARNING

Asphyxiation Risk

Negative pressure can cause spillage of combustion fumes and soot. Fire needs to draft properly for safe operation.

B. Negative Pressure

Negative pressure results from the imbalance of air available for the fireplace to operate properly. Causes for this imbalance include:

Exhaust fans (kitchen, bath, etc.).

Range hoods.

Combustion air requirements for furnaces, water heaters and other combustion appliances.

Clothes dryers.

Location of return-airvents to furnace or air conditioning.

Imbalances of the HVAC air handling system.

Upper level air leaks: recessed lighting, attic hatch opening, duct leaks.

To minimize the effects of negative air pressure, the following must be considered:

Install the outside air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace.

Avoid installing the fireplace near doors, walkways or small isolated spaces.

Recessed lighting should be a “sealed can” design; attic hatches weather stripped or sealed; attic mounted duct work and air handler joints and seams taped or sealed.

Basement installations should be avoided due to stack effect. Stack effect creates negative pressure in lower levels. Hearth & Home Technologies recommends the use of direct vent fireplaces in basements.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

5

Location of the fireplace and chimney will affect performance.

As shown in Figure 2.1 the chimney should:

Be installed through the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-downof the fire.

Penetrate the highest part of the roof. This minimizes the effects of wind turbulence.

Be located away from trees, adjacent structures, uneven roof lines and other obstructions.

Offsets can restrict draft so their use should be minimized. Consider the fireplace location relative to floor and ceiling and attic joists.

Recommended

Location Recommended

Location

Marginal

Location Location

Not

Recommended

Location

Not

Recommended

Windward

Outside Air Intake

Leeward

Multi-levelRoofs

Figure 2.1 Recommended Chimney Locations

6

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

C. Typical Fireplace System

The Heat & Glo fireplace system consists of the following:

Fireplace/integral grate/refractory/outside air system

Refractory

Chimney termination cap

Chimney system

Hearth extension

Glass Doors

Optional components include:

Chimney air kit

Additional lateral

support for chimney Termination cap above roof (or enclosed

in chase) if needed

Non-combustible

 

roof flashing maintains

Storm Collar

minimum clearance

around chimney

 

 

Chimney penetrates roof

 

preferably without affecting

Support straps

roof rafters

 

on rafter supports

 

chimney (not shown)

Offset/Return (with hanger straps)

 

 

Attic insulation shield (not shown) must

Ceiling firestop

be used here to keep insulation away

from chimney if attic is insulated

on floor of attic

 

Chimney system

Framing headed off

 

Combustible

in ceiling joists

 

framing/header

Enclosed space above

on top of

and around fireplace

V-shaped

 

standoffs

 

(spacers)

Mantel and surround

 

Decorative facing

 

and trim

Hearth extension

Outside

combustion air

Factory-builtfireplace

Protective metal hearth strip(s)

Figure 2.2 Typical Fireplace System

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

7

D. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw

Framing material

Pliers

High temp caulking material

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver

Electric drill and bits

Plumb line

Safety glasses

Level

Tape measure

1/2-3/4in. length, #6 or #8self-drillingscrews Misc. screws and nails

CAUTION

Keep fireplace dry.

Mold or rust may cause odors.

E. Inspect Fireplace and Components

WARNING

Fire Risk Explosion Risk

Inspect fireplace and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components

Report damaged parts to dealer.

Carefully remove the fireplace and components from the packaging.

The vent system components and doors are shipped in separate packages.

Report to your dealer any parts damaged in shipment.

Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

8

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

3

Framing and Clearances

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

 

Note:

 

 

Fire Risk

 

• Illustrations and photos reflect typical installations

 

 

Provide adequate clearances.

 

and are FOR DESIGN PURPOSES ONLY.

 

 

 

• Illustrations/diagrams are not drawn to scale.

 

 

Around air openings

 

 

 

To combustibles

 

• Actual installation/appearance may vary due to

 

 

For service access.

 

individual design preference.

 

 

 

• Hearth & Home Technologies reserves the right to

 

 

Locate fireplace away from traffic areas.

 

 

 

 

alter its products.

 

 

 

 

 

 

 

 

 

 

 

 

A. Selecting Fireplace Location

Several options are available to you when choosing a location for your fireplace. This fireplace may be used as a room divider, installed along a wall, across a corner or used in an exterior chase. See Figure 3.1.

Locating the fireplace in a basement, near frequently opened doors, central heat outlets or returns, or other locations of considerable air movement can affect the performance and cause intermittent smoke spillage from the front of the fireplace. Consideration should be given to these factors before deciding on a location. See Sections 2 and 10.

 

 

62 in.

12 in. (305 mm)

 

 

 

from opening of

 

 

 

(1575 mm)

 

72 in.

16 in.

fireplace

 

 

 

 

 

 

(1829 mm)

(406 mm)

 

 

Note: 1/2 in. min. distance from

16 in.

 

 

 

 

 

 

fireplace to combustible

(406 mm)

 

 

 

 

 

 

materials.

 

 

 

 

40-1/2in.

56 in.

 

Note: In addition to these

(1029 mm)

(1422 mm)

 

framing dimensions,

 

 

 

 

also reference the

 

26 in.

 

6 in.

following sections:

 

(660 mm)

 

(152 mm)

Clearances (Section

HEARTH

to front of

HEARTH

 

 

3.B.)

EXTENSION

fireplace

EXTENSION

 

Mantel Projections

(shaded)

opening

(shaded)

 

 

(Section 8.C)

 

 

 

 

 

BAY-40

64 in.

PIER-40

64 in.

• Fireplace Dimensions

(1626 mm)

(1626 mm)

(Section 12.A.)

Figure 3.1 Fireplace Locations

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

9

0 in. to level of standoffs

B. Clearances

WARNING

Fire Risk

Comply with all minimum clearances to combustibles as specified.

Framing or finishing material used on the front of, or in front of, the appliance closer than the minimums listed, must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.).

Failure to comply may cause fire.

Storm Collar

(roof)

Roof Flashing

 

2 in. (51 mm) min.

2 in. min.

Attic

(51 mm)

Insulation

 

(attic)

Shield

Ceiling Firestop

 

 

(ceiling)

2 in. (51 mm) min.

2 in. (51 mm) min.

 

Offset/Return with

Ceiling Firestop

hanger straps

 

(ceiling)

2 in. (51 mm) min.

2 in. (51 mm) min.

Must have 2 in. (51 mm) minimum clearance

to header

1/2 in. [13 mm] to back of appliance

1/2 in. (13 mm) to

0 in.

side of appliance

to floor

Figure 3.2 Clearances to Combustible Materials

10

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

C. Sidewalls/Surrounds

Adjacent combustible side walls must be located a minimum distance from the fireplace opening as per Figure 3.3.

 

 

62 in.

12 in. (305 mm)

 

 

 

from opening of

 

 

 

(1575 mm)

 

72 in.

16 in.

fireplace

 

 

 

 

 

 

(1829 mm)

(406 mm)

 

 

Note: 1/2 in. min. distance from

16 in.

 

 

 

 

 

 

fireplace to combustible

(406 mm)

 

 

 

 

 

 

materials.

 

 

 

 

40-1/2in.

56 in.

 

Note: In addition to these

(1029 mm)

(1422 mm)

 

framing dimensions,

 

 

 

 

also reference the

 

26 in.

 

6 in.

following sections:

 

(660 mm)

 

(152 mm)

Clearances (Section

HEARTH

to front of

HEARTH

 

 

3.B.)

EXTENSION

fireplace

EXTENSION

 

Mantel Projections

(shaded)

opening

(shaded)

 

 

(Section 8.C)

 

 

 

 

 

BAY-40

64 in.

PIER-40

64 in.

• Fireplace Dimensions

(1626 mm)

(1626 mm)

(Section 12.A.)

Figure 3.3 Sidewalls and Surrounds

D. Frame the Fireplace

Figure 3.4 shows a typical framing (using 2 x 4 lumber) of the fireplace, assuming combustible materials are used. All required clearances to combustibles around the fireplace must be adhered to. See Figure 3.2. Any framing across the top of the fireplace must be above the level of the top standoffs.

2 in. (51 mm) minimum air space clearance to enclosure

Mantel

12 in. max. (305 mm)

47-1/8in. (1197 mm) Header Height

2 in. (51 mm) minimum air space clearance to enclosure

Mantel

12 in. max.

(305 mm)

47-1/8in. (1197 mm) Header Height

BAY-40

PIER-40

Figure 3.4 Framing the Fireplace

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

11

E. Construct the Chase

A chase is a vertical boxlike structure built to enclose the fireplace and/or its vent system. Vertical chimneys that run on the outside of a building must be installed inside a chase.

Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner. All outer walls need to be insulated.

Building codes require false ceiling and ceiling firestops at each floor of the chase or every 10 ft (3.05 m) of clear space to control spread of fire.

Walls, ceiling, base plate and cantilever floor at the first level of the chase should be insulated. See Figure 3.5. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, Hearth & Home Technologies recommends that the inside surfaces be sheet rocked and taped (or the use of an equivalent method) for maximum air tightness.

Round Termination Cap

Metal Chase Top

Ceiling

Firestop

False Ceiling

Figure 3.5

Chase Assembly

Gas line holes and other openings should be caulked with high temperature caulk or stuffed with unfaced fiberglass insulation. If the fireplace is being installed on a cement slab, we recommend that in cold climates, a sheet of plywood or other raised platform be placed underneath to prevent conducting cold up into the room.

Three examples of chase applications are shown in Figure 3.6.

1.Fireplace and chimney enclosed in an exterior chase.

2.Chimney offset through exterior wall and enclosed in chase.

3.Chase constructed on roof.

1

2

Figure 3.6 Chase Constructions

F. Chimney Requirements

When planning your fireplace location, the chimney construction and necessary clearances must be considered. The fireplace system and chimney components have been tested to provide flexibility in construction. Vertical distances are measured from the base of the fireplace as shown in Figure 5.2.

Minimum overall straight height

14

(4.27 m)

Minimum height with offset/return

16.5 ft

(5.03 m)

• Maximum height

90 ft

(27.43 m)

• Maximum chimney length between an offset

20 ft

(6.1 m)

 

and return

 

 

• Maximum distance between chimney

35 ft

(10.67 m)

 

stabilizers

 

 

Double offset/return minimum height

20 ft

(6.1 m)

• Maximum unsupported chimney length

6 ft

(1.83 m)

 

between the offset and return

 

 

• Maximum unsupported chimney height above

35 ft

(10.67 m)

 

the fireplace

 

 

• Maximum unsupported chimney above roof

6 ft

(1.83 m)

Note: A maximum of two pairs of offsets and returns may be used.

12

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

4

Installation of Fireplace

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

WARNING

 

 

 

 

Fire Risk

 

Sharp Edges

 

 

 

 

 

Asphyxiation Risk

 

• Wear protective gloves and safety glasses

 

 

 

 

 

Do not draw outside combustion air from:

 

during installation.

 

 

 

 

 

• Wall, floor or ceiling cavity.

 

 

 

 

 

 

 

 

• Enclosed space such as an attic or

 

 

 

 

garage.

 

 

 

 

 

 

 

 

• Close proximity to exhaust vents or

 

 

 

 

chimneys.

A. Install the Outside Air Kit

 

Fumes or odor may result.

This fireplace will operate correctly only if adequate ventila-

 

 

 

tion is provided to allow proper draft to the fireplace system.

 

CAUTION

See Section 2.

 

The outside air kit is supplied with this fireplace. Using an

Risk of Smoke Spillage

outside air kit is highly recommended to minimize the effects

Outside air inlet must be located to prevent blockage

of negative pressure within the structure. We recommend

from:

 

 

you utilize the shortest duct run to optimize the performance

Leaves

of the outside air kit. Cold air flow can be minimized by put-

Snow/ice

ting a small dip in the duct creating a cold air trap. This trap

Other debris

can also help prevent heat build-upand exhausting out the

Blockage may cause combustion air starvation.

intake due to the stack effect. The outside air kit inlet should

 

 

 

be positioned in a manner that will not allow snow, leaves,

 

 

 

etc. to block the inlet. In some installations the air duct

The outside air kit is installed on the right side (PIER-40)

may need to be run vertically. In such an installation, a 3 ft

or open end (BAY-40)of the fireplace. See Figure 4.4 for

(.914 m) height difference must be maintained from the top

handle location/operation.

of the uppermost chimney section to the outside combustion

Remove the cover plate from the side (PIER-40)or bottom

air inlet. See Figure 4.2.

(BAY-40)of the fireplace assembly where the air kit is to be

See Figure 4.3 for proper placement of outside air inlet.

installed.

Flexible Duct (not supplied)

 

 

Outside Air

Outside Air

 

Plate

 

Assembly

Shield

2 Wire Ties

 

Figure 4.1 Outside Air Installation

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

13

3 ft min. from top of uppermost chimney section to air inlet.

Figure 4.2 Outside Air Inlet Locations

Attic insulation shield must be used to keep insulation away from chimney.

Ceiling firestop on floor of attic.

LIFT TO

OPEN

BAY-40

PULL TO

OPEN

PIER-40

Figure 4.4 Locating the Outside Air Control

NO

NO

 

Garage or

NO

Outlet blocked by

combustible

snow, leaves, etc.

liquids storage

Attic space

NO

Outlet placed higher than 3 ft below the termination cap

YES

Factory-built

Clear area

fireplace

outside

 

house or in

 

ventilated

 

crawl space

Use only duct materials specified

 

by manufacturer (preferably with

 

short run or mainly straight duct,

 

except small dip for cold air trap

 

which will help prevent flow of cold air).

Figure 4.3 Outside Combustion Air Placement

14

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

B. Secure the Fireplace

Position the Fireplace

This fireplace may be placed on either a combustible or noncombustible continuous flat surface. Follow the instructions for framing in Section 3.D. Slide the fireplace into position. Be sure to provide the minimum air clearance at the sides and back of the fireplace assembly. See Section 3.B.

WARNING

Fire Risk!

Prevent contact with sagging, loose insulation.

Do NOT install against vapor barriers or exposed insulation.

Place the Protective Metal Hearth Strips

WARNING

Fire Risk!

• Metal hearth strips MUST be installed. Sparks or embers may ignite flooring.

Included with your fireplace you will find two metal hearth strips measuring approximately 26 in. x 4 in. (660 mm x 102 mm). These strips are used to provide added protection where the fireplace and the hearth extension meet.

Slide each metal strip 2 in. (51 mm) under the front edge of the fireplace. The individual pieces must overlap each other by 1 in. (25 mm) minimum in the middle of the fireplace to provide continuous coverage of the floor. See Figure 4.5. These metal strips should extend from the front and sides of the fireplace opening by 2 in. (51 mm).

Note: When elevating the fireplace above the hearth extension the front of the elevated platform must be protected with a protective metal hearth strip as shown in Figure 4.6.

Level the Fireplace

Level the fireplace side-to-sideandfront-to-back.Shim with noncombustible material, such as sheet metal, as necessary. Secure the fireplace (using the nailing flanges located on either side of the fireplace) to the vertical framing.

Important: To ensure proper fit of the glass doors, check the fireplace opening for square. Measure diagonal distances of the opening to make sure they are equal. If they are not, continue to shim the fireplace until those diagonals are equal.

1 in. (25 mm) overlap

Metal strips 2 in. (51 mm) under the edges of the fireplace and must extend beyond the front and side openings by 2 in. (51 mm)

Figure 4.5 Position the Protective Metal Hearth Strips

 

Top piece must overlap

 

bottom piece

 

Raised Platform

2 in.

1 in. (25 mm) min.

(51 mm)

overlap

Floor

2 in. (51 mm)

Figure 4.6 Protect the Front of an Elevated Platform

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

15

5 Chimney Assembly

Chimney must extend beyond combustible roof structure

Maintain minimum height of chimney above roof

Install roof flashing according to minimum requirements

Offsets/returns may not exceed 30° from vertical

Lock chimney sections together firmly to resist movement

Termination Cap

Additional support for tall chimneys

Storm Collar

Maintain minimum clearances to combustibles as specified

Support straps for offsets/ returns must be secured to adequate framing

Ceiling firestops are required where chimney passes through ceiling or floor

Figure 5.1 Typical Chimney System - Guidelines for Chimney System Installation

NOTE:

Chimney performance may vary.

Trees, buildings, roof lines and wind conditions affect performance.

Chimney height may need adjustment if smoking or overdraft occurs.

16

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

A. Chimney Requirements

Vertical distances are measured from the base of the fireplace as shown in Figure 5.2.

Minimum overall straight height

14

(4.27 m)

Minimum height with offset/return

16.5 ft

(5.03 m)

• Maximum height

90 ft

(27.43 m)

• Maximum chimney length between an offset

20 ft

(6.1 m)

 

and return

 

 

• Maximum distance between chimney

35 ft

(10.67 m)

 

stabilizers

 

 

Double offset/return minimum height

20 ft

(6.1 m)

• Maximum unsupported chimney length

6 ft

(1.83 m)

 

between the offset and return

 

 

• Maximum unsupported chimney height above

35 ft

(10.67 m)

 

the fireplace

 

 

• Maximum unsupported chimney above roof

6 ft

(1.83 m)

Note: A maximum of two pairs of offsets and returns may be used.

WARNING

Fire Risk

Must maintain 2 in. (51 mm) air clearance to insulation and other combustible materials.

Table 5.1

HEIGHT OF CHIMNEY COMPONENTS

in.

mm

Chimney Stabilizer

 

 

 

SL11

4-3/4

121

Ceiling Firestops

 

 

 

FS538

0

0

 

FS540

0

0

Offsets/Returns

 

 

 

SL1130

18

457

Roof Flashing

 

 

 

RF570

0

0

 

RF571

0

0

Chimney Sections*

 

 

 

SL1106

4-3/4

121

 

SL1112

10-3/4

273

 

 

 

 

 

SL1118

16-3/4

425

 

 

 

 

 

SL1136

34-3/4

883

 

SL1148

46-3/4

1187

* Dimensions reflect effective height.

 

 

To determine the chimney components needed to complete your particular installation, follow the steps below:

Determine the total vertical height of the fireplace installation. This dimension is measured from the base of the fireplace assembly to the point where the smoke exits the termination cap.

Subtract the effective height of the fireplace assembly from the overall height of the fireplace installation (measured from the base of the fireplace to the bottom of the termination cap).

Refer to Table 5.1 to determine what components must be selected to complete the fireplace installation.

Determine the number of ceiling firestops, stabilizers, roof flashing, etc. required to complete the fireplace installation.

6 ft (1.8 m) max. unsupported run

20 ft (6.10 m) max. pipe between an offset & return

Ceiling Firestop

44 in.

(1118 mm) Effective Height

6 ft (1.83 m) max. unsupported chimney above roof

35 ft (10.7 m) max. straight unsupported chimney height

13.25 ft (4.04 m) min. height/single offset-return

20 ft. (6.10 m) min. height/double offset-return

90 ft (27.4 m) max. height

Figure 5.2 Chimney Requirements

CAUTION

Do NOT connect this fireplace to a chimney flue servicing another appliance.

Do NOT connect to any air distribution duct or system.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

17

B. Using Offsets/Returns

To bypass any overhead obstructions, the chimney may be offset using an offset/return.

An offset and return may be attached together or a chimney section(s) may be used between an offset and return.

Perform the following steps to determine the correct chimney component combination for your particular installation:

WARNING

Fire Risk

Draft will be restricted if offset/returns greater than 30° are used.

Measure how far the chimney needs to be shifted to enable it to avoid the overhead obstacle. See Figure 5.3. Use dimension “A” to determine chimney section required to achieve the needed shift.

After determining the offset dimension, refer to Table 5.2 and find the “A” dimension closest to but not less than the distance of shift needed for your installation.

The “B” dimension that coincides with the “A” dimension represents the required vertical clearance that is needed to complete the offset and return.

Read across the chart and find the number of chimney sections required and the model number of those particular chimney parts.

Whenever the chimney penetrates a floor/ceiling, a ceiling firestop must be installed.

The effective height of the fireplace assembly is measured from the base of the fireplace to the top of the starter collar. See Dimensions in Section 12.

Table 5.2

 

A

 

B

 

 

 

 

 

in.

 

mm

in.

 

mm

SL1106

SL1112

SL1118

SL1136

SL1148

4 7/8

 

124

17 7/8

 

454

-

-

-

-

-

 

 

 

 

 

 

 

 

 

 

 

7 1/4

 

184

22

 

559

1

-

-

-

-

9 3/4

 

248

26 1/8

 

664

2

-

-

-

-

 

 

 

 

 

 

 

 

 

 

 

10 1/4

 

260

27 1/4

 

692

-

1

-

-

-

12 3/4

 

324

31 3/8

 

797

1

1

-

-

-

13 1/4

 

337

32 3/8

 

822

-

-

1

-

-

15 3/4

 

400

36 5/8

 

930

-

2

-

-

-

18 1/8

 

460

40 3/4

 

1035

1

2

-

-

-

 

 

 

 

 

 

 

 

 

 

 

18 3/4

 

476

41 3/4

 

1060

-

1

1

-

-

21 3/4

 

552

47

 

1194

-

-

2

-

-

 

 

 

 

 

 

 

 

 

 

 

22 1/4

 

565

4 8

 

1219

-

-

-

1

-

24 3/4

 

629

52 1/8

 

1324

1

-

-

1

-

27 3/4

 

705

57 3/8

 

1457

-

1

-

1

-

28 1/4

 

718

58 3/8

 

1483

-

-

-

-

1

30 3/4

 

781

62 1/2

 

1588

1

-

-

-

1

 

 

 

 

 

 

 

 

 

 

 

33 3/4

 

857

67 3/4

 

1721

-

1

-

-

1

36 3/4

 

933

73

 

1854

-

-

1

-

1

 

 

 

 

 

 

 

 

 

 

 

39 3/4

 

1010

78 1/8

 

1984

-

-

-

2

-

41 1/8

 

1045

82 3/8

 

2092

1

-

-

2

-

 

 

 

 

 

 

 

 

 

 

 

45 3/4

 

1162

88 1/2

 

2248

-

-

-

1

1

 

 

 

 

 

 

 

 

 

 

 

48 1/8

 

1222

92 3/4

 

2356

1

-

-

1

1

51 3/4

 

1314

98 7/8

 

2511

-

-

-

-

2

Proper assembly of air cooled chimney parts results in an overlap of chimney joints of 1-1/4in. (32 mm). Effective length is built into this table.

A

B

1-1/4in. (32 mm) OVERLAP

Figure 5.3 Chimney Offset/Return

Example: Your “A” dimension from Figure 5.3 is 14 1/2 in. (368 mm). Using Table 5.2 the dimension closest to, but not less than 14 1/2 in. (368 mm) is 15 3/4 in. (400 mm) using a 30° offset/return. It is then determined from the table that you would need 36 5/8 in. (930 mm) (Dimension “B”) between the offset and return. The chimney components that best fit your application are two SL1112s.

18

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

C. Assemble the Chimney Sections

Attach either a straight chimney section or an offset to the top of the fireplace (depending on your installation requirement). Chimney sections are locked together by pushing downward until the top section meets the stop bead on the lower section.

The inner flue is placed to the inside of the flue section below it. The outer casing is placed outside the outer casing of the chimney section below it. See Figure 5.4.

Figure 5.4 Assembling Chimney Sections

Note: Inner flue and outer liner sections cannot be disassembled once locked together. Plan ahead to ensure the proper installation height is achieved with the selected chimney components.

WARNING

Fire Risk

Do NOT install substitute or damaged chimney components.

MUST use chimney system described in this manual.

NO OTHER chimney components may be used.

Substitute or damaged chimney components may impair safe operation.

D. Install the Ceiling Firestops

Mark and cut an opening in the ceiling for the ceiling firestop being used. See Figure 5.5.

Frame the opening with the same size lumber used in the ceiling joists.

Install the ceiling firestop.

Note: The ceiling firestop MUST be nailed to the bottom of the ceiling joists EXCEPT when the space above is uninsulated and the attic insulation shield is not being used (see Figure 5.5). When the attic insulation shield is used the ceiling firestop may be above or below the joist of an insulated ceiling.

ROOM ABOVE (non-insulatedceiling)

B

A

Ceilng firestop from bottom

ATTIC ABOVE (insulated ceiling)

Ceiling firestop from

When attic insulation

top

shield not used

Note: Use same dimensional lumber for framing ceiling firestop and joists.

 

A

 

 

B

Catalog #

in.

 

mm

in.

 

mm

FS538

17

 

432

17

 

432

FS540

17

 

432

26

 

660

Figure 5.5 Installing the Ceiling Firestop

Note: You must provide support for the pipe during construction and check to be sure inadvertent loading has not dislodged the chimney section from the fireplace or at any chimney joint.

CAUTION

Ceiling firestops must be used at ceiling/floor.

Chase construction requires ceiling firestops at each floor or every 10 ft (3.05 m) of clear space.

Use same dimensional lumber as joists.

Ceiling firestop slows spread of fire and reduces cold air infiltration.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

19

¨E. Install the Attic Insulation Shield

 

 

Tabs bent in to

 

 

 

 

 

Pipe

rest against pipe

WARNING

 

 

 

 

 

Fire Risk

 

 

Attic Insulation Shield

• DO NOT pack insulation or other

 

 

17 in. (432 mm)

combustibles: between ceiling firestops;

 

6 Tabs bent

diameter

between chimney and attic insulation

 

in 90°

Ceiling Firestop

shield.

 

 

 

• ALWAYS maintain specified clearances

 

 

 

around chimney and ceiling firestop

Insulation

Pipe

Insulation

systems.

 

 

 

Install ceiling firestops as specified.

Failure to keep insulation or other material

13 in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(330 mm)

 

 

 

 

 

 

 

 

 

 

away from chimney pipe may cause fire.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

An insulation shield must be installed when there is a pos-¨ Figure 5.7 Install Attic Insulation Shield Above the Ceiling

sibility of insulation coming into contact with the factory built

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

chimney system. Installation of a ceiling firestop is required

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tabs bent in to

(see Figures 5.7 and 5.8).

 

 

 

 

 

 

 

 

• Roll the shield (around the chimney if already installed)

 

 

 

 

 

 

 

 

rest against pipe

 

 

 

 

 

Pipe

 

 

 

 

 

until you have a 3 in. (76 mm) overlap and the three holes

 

 

 

 

 

 

 

 

 

 

 

on each side match up (large holes on top).

 

 

 

 

 

 

 

 

 

Attic Insulation Shield

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Insert three screws into the matching holes to form a

 

 

 

 

 

 

 

 

 

 

17 in. (432 mm)

tube.

 

 

 

 

 

 

 

 

 

 

diameter

 

 

 

 

 

6 Tabs bent

 

 

 

 

 

• Bend three tabs on the bottom of the tube inward to 90°

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in 90°

 

 

 

 

 

to maintain chimney clearance. See Figure 5.6.

Insulation

 

 

 

 

 

 

 

 

 

Insulation

• Rest the insulation shield on the ceiling firestop below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Bend the three short tabs at the top of the shield inward

13 in.

 

 

 

 

 

 

 

 

 

Ceiling Firestop

 

 

 

 

 

 

 

 

 

to 90° to maintain the 2 in. (51 mm) clearance from the

 

 

 

 

Pipe

 

 

 

 

(330 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

chimney.

 

 

 

 

 

 

 

 

 

 

 

Bend the remaining top tabs to just meet the pipe.

 

 

¨ Figure 5.8 Install Attic Insulation Shield Below the Ceiling

 

Bend remaining tabs

 

 

to rest against pipe to

If you wish to make a custom shield or barrier, follow these

Bend inward

prevent insulation

guidelines:

from falling in.

90°

• Metal is preferred, although any material stiff enough to

 

 

 

Insert three

hold up against the insulation can be used.

 

• The shield or barrier must be tall enough to extend above

 

screws

the insulation and prevent blown-ininsulation from spilling

 

 

into the cavity.

 

 

• Maintain specified cleaances around chimney.

 

 

• Check instructions and local codes for further details.

3 in. (76 mm) overlap

Figure 5.6 Prepare Attic Insulation Shield

20

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

F. Double-checkthe Chimney Assembly

Continue assembling the chimney sections up through the ceiling firestops as needed. While doing so, be aware of the height and unsupported chimney length limitations given under Section 5.A. Chimney Requirements.

Check each section by pulling up slightly from the top to ensure proper engagement before installing the succeeding sections. If they have been connected correctly, they will not disengage when tested.

G. Secure the Chimney

When offsets and returns are joined to straight pipe sections, they must be locked into position with the screws provided* (outer only), using the predrilled holes. To prevent gravity from pulling the chimney sections apart, the returns and the chimney stabilizers have hanger straps for securing these parts to joists or rafters. See Figure 5.9.

*or equivalent #6 or #8 sheet metal screw no longer than 3/4 in. (19 mm).

WARNING

Fire Risk

Secure offsets with screws (not to exceed 3/4 in./19 mm in length).

Secure returns with strapping.

Straight chimney sections may be secured with screws (not to exceed 3/4 in./19 mm in length) at the joints.

Keep chimney sections from separating or twisting.

Ceiling

Firestop

Straps

Joint

Band

Optional (Optional)

Additional

Support

Figure 5.9 Secure the Chimney

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

21

6 Complete the Enclosure

A. Chimney Termination

Chimney Termination Requirements (See Figures 6.1 and 6.2)

Must have a cap approved and listed for this fireplace system

Must not be located where it will become plugged by snow or other material

Must terminate at least 3 ft (914 mm) above the roof and at least 2 ft (610 mm) above any portion of the roof within 10 ft (3.05 m)

Must be located away from trees or other structures

Slanted Roofs

Chimney must extend 3 ft (.9 m) above the roof

Chimney must extend 2 ft (.6 m) above any portion of the roof within 10 ft (3 m) of the chimney

Flat Roofs

Chimney must extend 3 ft (.9 m) above the roof

Chimney must extend 2 ft (.6 m) above any portion of the roof within 10 ft (3 m) of the chimney

Figure 6.1 Termination Requirements

Gas, Wood or Fuel

Termination Caps Same Height

Oil Termination

 

 

 

8 ft

 

Gas, Wood or Fuel

 

 

A

(2.44 m)

 

Oil Termination

 

18 in.

(min. for B-Vent)

 

 

 

 

 

 

 

20 in.

 

 

8 ft

(457 mm)

 

(508 mm)

 

 

 

 

 

 

(2.44 m)

 

 

(min. for direct vent)

 

 

B

 

 

 

(min. for B-Vent)

 

to

 

 

 

Wood

20 in. min. *

20 in.

 

 

Perpendicular

 

 

Wall

 

(508 mm)

(508 mm)

 

 

 

(min. for direct vent)

Gas

 

 

 

 

to

Termination

 

 

 

 

Perpendicular

 

 

 

 

 

Wall

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Termination Caps Staggered Height

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* If using decorative cap cover(s), this distance may

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

Gas Termination

Wood or Fuel Oil Termination

 

 

need to be increased. Refer to the installation instruc-

 

 

B

 

6 in. (152 mm) min.

 

 

 

20 in. (508 mm) min.

 

 

 

tions supplied with the decorative cap cover.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 6.2

Multiple Chimneys

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

Mark the Exit Point of the Roof

Locate the point where the chimney will exit the roof by plumbing down to the center of the chimney. Drive a nail up through the roof to mark the center. See Figure 6.3.

¨Cut Out the Hole in the Roof

Measure to either side of the nail and mark the 17 in. x 17 in. (432 mm x 432 mm) opening required. This is measured on the horizontal; actual length may be larger depending on the pitch of the roof. Cut out and frame the opening. See Chapter 25 of theUniform Building Code for roof framing details.

WARNING

 

Fire Risk

 

• Must maintain 2 in. (51 mm) air clearance

 

to insulation and other combustible

 

materials.

 

Assemble the Chimney Sections Through the

 

Roof

 

Continue to add chimney sections through the roof open-

 

ing, maintaining at least a 2 in. (51 mm) air space to com-

 

bustible materials.

 

Install the Roof Flashing

 

If a roof flashing is to be used, install the roof flashing

 

appropriate to the roof pitch and install a round termination

 

cap and storm collar following the instructions shipped with

 

the cap.

Figure 6.3 Ceiling/Attic Construction

Install the Chimney Air Kit (required in Canada):

 

When installing the chimney air kit, follow the instructions

 

provided with this accessory.

 

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

23

B. Chase Top

A metal chase top is required to seal the top of the chase around the chimney pipe. The top should include a turndown and drip edge to prevent water from seeping into the chase. Provide a 1/8 in. (3 mm) gap around the flue pipe and slope the top downward away from the penetration. See Figure 6.4.

All seams must be caulked to prevent leaks.

A chase installation must use a chase top. Chase tops are available from your Heat & Glo dealer or may be field constructed.

Attach the chase top to the top of the chase.

Termination Cap

2 in. (51 mm) Collar

on Chase Top

Caulk

Storm Collar

Slope Downward

Turn-down

Drip Edge

Chase

(Chimney)

.018 (26 ga) min. Galvanized Chase Top

Figure 6.4 Chase Top Construction

C. Install the Termination Cap

Note: To protect against the effect of corrosion on those parts exposed to the weather, the termination cap can be painted with arust-resistantpaint.

WARNING

Fire Risk

The minimum overlap of cap to pipe MUST be met or chimney may separate from cap.

Separation allows sparks, heat and embers to escape.

Install the chimney sections up through the chase enclosure. When using a TR11 Round Termination Cap, the uppermost top section of pipe must extend 6 in. (152 mm) above the top of the flashing collar to allow installation of the storm collar and termination cap. See Figure 6.5.

Minimum 1-1/2in. (38 mm) overlap of cap over pipe

Storm Collar

2 in. (51 mm) min.

6 in. (152mm) min.

Flashing Collar

2 in. (51 mm) min. collar

Figure 6.5 Installing a TR11 Round Termination Cap

For installations utilizing a TR11T Round Telescoping Termination Cap, the uppermost chimney section must be below the top of the chase top, but not more than 14-1/2in. (368 mm) below the top of the chase top. Minimum overlap of chimney and termination cap must be1-1/2in. (38 mm). See Figure 6.6.

 

Storm Collar

Flashing Collar

2 in. (51 mm) min.

 

14-1/2in. (368mm) max.

Top of Pipe

1-1/2in. (38 mm) min.

 

 

overlap

Figure 6.6 Installing a TR11T Round Telescoping Termination Cap

24

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

For installations utilizing an ST1175 Square Termination Cap the last chimney section must not be more than 4-1/2in. (114 mm) below the chase top. See Figure 6.7.

 

 

Flashing Collar

Cap Standoff

 

2 in. (51 mm) min.

 

 

1-1/2in.

 

4-1/2in.

(38 mm) min.

 

(114 mm)

overlap

Top of Pipe

max.

Figure 6.7 Installing an ST1175 Square Termination Cap

For installations utilizing an TCT1175 Terra Cotta Cap the last chimney section must be between 7 in. (178 mm) below the chase top and 2 in. (51 mm) above. See Figure 6.8.

1-1/2in. (38 mm) min. overlap

{

Top of Pipe

The last section of pipe must stop between the distances given below.

2 in. (51 mm) above top of the chase.

7 in. (178 mm) below top of the chase.

Figure 6.8 Installing a TCT1175 Terra Cotta Cap

For chase installations you can use a TR11 Round Termination Cap, a TR11T Round Telescoping Termination Cap, an ST1175 Square Termination Cap, or a TCT1175 Terra Cotta Termination Cap.

For installations utilizing a European Copper Series Termination Cap, See Figure 6.9.

Install termination caps following instructions provided with them.

Cap Base

bracket (8)

screw (8)*

chimney top

chase top

(metal or masonry) SL pipe inner flue

(cap inner flue)

2 - 6 in.(51-152mm)

2 in. (51 mm) typical

Figure 6.9 Installing a European Copper Series Termination Cap (CT3-Kingshown)

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

25

7

Accessories

 

 

 

 

 

A. Gas Log/Lighter Provisions

 

 

WARNING

 

A certified gas log lighter or decorative gas log set can be

 

installed in this fireplace.

 

 

Asphyxiation Risk

 

• Maximum input is 100,000 BTU/hr.

 

• Damper must be locked open when gas logs

 

• Decorative gas appliance must be certified to ANSI Z21.60

installed.

 

“Standard for Decorative Gas Appliances for Installation

Gas fire generates fumes.

 

in Vented Fireplaces”.

 

 

 

Must be installed in accordance with the National Fuel

Gas Code, ANSI Z223.1.

A log set must incorporate a gas shutoff.

Log set requires the damper to be locked fully open.

Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe.

We recommend you seal refractory around pipe with fireplace mortar or high temperature, noncombustible sealant.

Repack insulation from the knockout around the pipe.

Maintain 1-1/2in. (38 mm) air space around the pipe for 4 in. (102 mm) beyond the fireplace.

See Figure 7.1.

Firebox

Refractory

Seal with fireplace mortaror high tempnoncombustiblesealant

Outer Shell

of Fireplace

Maintain air clearanceto combustibles.

Combustible

Materials

Gas Line

Repack

Insulation

Knockout

 

 

 

 

 

 

 

 

 

 

 

1-1/2in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(38 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gas Line

 

 

 

 

 

air space

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Combustible materials

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

may be located at zero

 

 

 

 

 

 

 

 

 

 

 

 

clearance to gas line

 

 

 

 

 

 

 

 

 

 

 

 

beyond 4 in. (102 mm)

 

 

 

4 in.

 

 

from fireplace side.

 

 

 

 

 

 

(102 mm)

 

 

 

 

 

 

Figure 7.1 Gas Line Installation

WARNING

Fire Risk

For use with solid wood fuel or decorative gas appliance only.

DO NOT install unvented gas logs.

WARNING

Fire Risk Explosion Risk

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components

Report damaged parts to dealer.

26

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

8 Finishing

A. Hearth Extension

A hearth extension must be installed with all fireplaces to protect the combustible floor in front of the fireplace from both radiant heat and sparks. See Figures 8.1-8.3.

WARNING

Fire Risk

• Metal hearth strips MUST be installed. Sparks or embers may ignite flooring.

This fireplace has been tested and approved for use with a hearth extension insulated to a minimum R value of 1.03.

To substitute materials for the factory-availablehearth extensions, see Figure 8.3 and calculate insulation alternatives as per Table 8.1 and the following formulas:

Thermal conductivity per inch thickness = k

k = (BTU)(inch) / (foot2)(hour)(°F)

Required thickness = Rk

Thermal resistance per inch thickness = r

r = (foot2)(hour)(°F) / (BTU)(inch)

Required thickness = R / rB.

 

High temperature

 

 

 

 

(300°F min.) continuous,

 

 

HX3 or HX4

non-combustiblesealant

Fireplace

 

non-combustiblematerial

Protective

insulation

Hearth Ext

Tile, stone or other

 

 

or equivalent

 

 

 

 

 

 

(see Table below)

 

 

 

Metal Hearth

 

 

 

 

Strip

 

 

2 in. (51 mm)

 

 

Floor constructed of wood or

required

 

 

other combustible material

 

 

 

Figure 8.1 Hearth Extension Construction

¨Table 8.1

Hearth Extension Insulation Alternatives-Totalminimum R Value must equal 1.03

 

 

 

Minimum

 

k per inch

r per inch

thickness

Material

thick

thick

required

Hearth & Home HX3, HX4 (Micore 300™)

0.49

2.06

1/2 in.

 

 

 

 

USG Micore 160™

0.39

2.54

1/2 in.

USG Durock™ Cement Board

1.92

0.52

2 in.

 

 

 

 

Cement Mortor

5.0

0.20

5-1/8in.

Common Brick

5.0

0.20

5-1/8in.

Ceramic Tile

12.50

0.08

12-1/4in.

 

 

 

 

Armstrong™ Privacy Guard Plus

0.46

2.18

1/2 in.

Marble

14.3-20.0

0.07-0.05

14-5/8in. -20-3/8in.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

27

1 in. (25 mm) overlap

Metal strips 2 in. (51 mm) under the edges of the fireplace and must extend beyond the front and side openings by 2 in. (51 mm)

Figure 8.2 Positioning the Protective Metal Hearth Strips

WARNING

Fire Risk

Hearth extensions must be installed exactly as specified.

High temperatures or hot embers may ignite concealed combustibles.

 

A

C

B

 

 

 

 

 

 

 

 

CAT. #

 

A

B

C

HX3

in

52

16

8

 

mm

1321

406

203

Figure 8.3 Hearth Extension Dimensions

B. Finishing Material

Combustible Material

Material which is made of or surfaced with wood, compressed paper, plant fibers, plastics, or any material capable of igniting and burning, whether flame proofed or not, plastered or not plastered.

Non-CombustibleMaterial

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750° C, shall be considered non-combustible materials.

Non-CombustibleSealant Material

Sealants which will not ignite and burn: Rutland, Inc. Fireplace Mortar #63, Rutland 72R, Nuflex 302, GE RTV106, GE RTV116.

After completing the framing and applying the facing material (drywall) over the framing, a bead of non-combustiblesealant must be used to close off any gaps at the top and sides between the fireplace and facing to prevent cold air leaks. Large gaps can be bridged with fiberglass rope gasket.

Only non-combustiblematerials may be used to cover the metal fireplace front.

WARNING

Fire Risk

Maintain clearances.

Use only non-combustiblematerial below standoffs, material such as cement board is acceptable.

Framing or finishing material used on the front of, or in front of, the appliance closer than the minimums listed, must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.).

28

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

C. Mantel

A combustible mantel may be positioned no lower than 12 in. (305 mm) above the top of the fireplace opening. The combustible mantel may have a maximum depth of 12 in. (305 mm). Combustible trim pieces that project no more than 1-1/2in.(38 mm) from the face of the fireplace can be placed no closer than 6 in. (152 mm) from the top of the fireplace opening. See Figure 8.4. Combustible trim must not cover the metal surfaces of the fireplace. This mantel clearance is in accordance withSection 7-3.3.3 of ANSI/ NFPA211.

WARNING

Fire Risk

Do NOT obstruct air inlets.

Finishing materials must not interfere with:

Air flow through inlets

Operation of doors

Access for service

D.Sidewalls/Surrounds

Adjacent combustible side walls must be located a minimum of 12 in. (305 mm) from the fireplace opening. If you are using a decorative surround constructed of combustible material, it must be located within the shaded area defined in Figure 8.5. Short stub walls are also acceptable if they are contained within the shaded area.

E. Glass Doors

This fireplace has been tested and listed with doors (required). See Section 12B Fireplace Components for available doors. Please refer to the manual packed with each set of doors for installation instructions.

 

12 in. (305 mm)

 

 

 

 

max.

 

1-1/2in. (38 mm) max.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Header

Mantel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standoff

12 in. (305 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top of

Fireplace

Opening

6 in. (152 mm) min.

Figure 8.4 Mantel Specifications

 

 

 

62 in.

 

 

 

12 in.

 

 

 

 

 

 

 

 

 

 

 

(305 mm)

 

 

 

(1575 mm)

 

 

72 in.

 

16 in.

 

 

from opening

 

 

 

 

 

 

 

of fireplace

 

 

(1829 mm)

 

(406 mm)

 

 

 

 

 

 

 

16 in.

(406 mm)

40-1/2in.

56 in.

(1029 mm)

(1422 mm)

 

26 in.

6 in.

 

(660 mm)

(152 mm)

HEARTH

to front of

HEARTH

EXTENSION

fireplace

EXTENSION

(shaded)

opening

(shaded)

BAY-40

64 in.

PIER-40

64 in.

(1626 mm)

(1626 mm)

Figure 8.5 Sidewalls/Surrounds

WARNING

Fire Risk

Finish all edges and fronts to clearances and specifications.

• Metal fireplace front may be covered with non-combustiblematerial only.

Do NOT overlap combustible materials onto fireplace front.

Install combustible materials up to specified clearances on top front and side edges.

Seal joints between the finished wall and fireplace top and sides using only a 300° F minimum sealant.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

29

9 Operating Instructions

WARNING

¨

WARNING

 

Fire Risk

Do not operate fireplace before reading and understanding operating instructions.

Failure to operate fireplace properly may cause fire.

A. General Information

Fireplaces, as well as other woodburning appliances, have been used safely for many years. It has been our experience that most problems are caused by improper installation and operation of the fireplace. Make certain that installation and operation of the fireplace system is in accordance with these instructions.

It is extremely important that the fire be supervised whenever the fireplace is in use. It is also recommended that an annual inspection be performed on the fireplace system to determine if the flue system needs to be cleaned, or as in the case of any appliance, if minor repairs are required to maintain the system in top operating condition.

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

Do not touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

WARNING

Fire Risk

For use with solid wood fuel or decorative gas appliance only.

Do not install unvented gas logs.

Damper Control

Up - Open

Down - Closed

Outside Air Control

Handle Out - Open

Handle In - Closed

LIFT TO OPEN

BAY-40

PULL TO

OPEN

Figure 9.1 General Operating Parts

PIER-40

30

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

B. Outside Air

A source of air (oxygen) is required in order for combustion to take place. Whatever air is consumed by the fire must be replaced through cracks around windows, under doors, etc. Most newly constructed houses or existing homes fitted with tightly sealed doors and windows are relatively air tight. In this case, an outside air source must be made available to feed combustion air from outside the home.

An outside air control handle allows you control of the outside air inlet if your fireplace is equipped with this option. Use of outside air for combustion is highly recommended to conserve heated air within the structure and to provide make up air to keep the fireplace venting properly.

This fireplace will operate correctly only if adequate ventilation is provided to allow proper draft to the fireplace system.

See Figure 9.1 for location and operation.

CAUTION

Outside air control handle is HOT. Adjust before lighting fire.

C. Clear Space Near the Fireplace

Combustible materials must not be stored on the hearth extension. Room furnishings such as drapes, curtains, chairs or other combustibles must be at least 4 ft (1.22 m) from the open front of the fireplace.

D. Flue Damper

The flue damper must be in full open position, and is operated by moving the handle up toward the top of the fireplace. Before lighting the fire, verify this by looking up from the inside of the fireplace. Always operate this fireplace with the damper fully open. Please note: Down drafts, obstructions, damaged or poor (wet) fuels can cause smoke spillage.

See Figure 9.1 for location and operation.

WARNING

Asphyxiation Risk

Fire Risk

Open damper to operate fireplace.

Closed damper will over-firefireplace and prevent venting of combustion gases.

E. Firescreen

A firescreen is always provided to control sparks. It must be closed whenever the fireplace is in use. Glass doors or firescreens must not be used to hold burning material inside the fireplace. Only those glass doors specifically tested and listed for use with the specific fireplace model should be used. Screens should be closed when the glass doors are closed.

WARNING

Fire Risk

Close firescreen when burning fireplace.

Do not use firescreen or glass doors to hold burning material in fireplace.

Firescreen controls sparks.

Glass may break or burning material may roll out.

F. Glass Doors

Most efficient fireplace operation using glass doors is with the doors open. When the doors are open the screen must be closed. Only Hearth & Home Technologies glass doors may be used. See Figure 9.2 for proper glass door operation.

FULLY OPEN

PARTLY OPEN

CORRECT

INCORRECT

FULLY CLOSED

PARTLY CLOSED

CORRECT

INCORRECT

Figure 9.2 Proper Operating Positions of Bi-foldDoors

WARNING

Fire Risk

Smoke Risk

Doors must be fully opened or fully closed when operating fireplace.

Partially opened doors may draw flame, smoke or heat from fireplace.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

31

G. Grate

The factory installed integral grate must be used to hold the logs from falling out of an open fireplace and to allow air to pass between the burning logs. It is important to keep the fire off the hearth and to allow the ashes to collect beneath the fire, thereby forming a layer of additional heat protection.

WARNING

Fire Risk

Use only factory installed integral grate. May cause overfire.

H. Wood Fuel

Firewood

Your fireplace performance depends on the quality of the firewood you use. All seasoned wood, regardless of species, contains about 8,000 BTU’s per pound, and hardwoods have a greater density than soft woods. A piece of hardwood will contain about 60% more BTU’s than an equal size piece of soft wood. Firewood is commonly sold by the cord (128 cu. ft.). A cord of seasoned oak (hardwood) would contain about 60% more potential energy than a cord of seasoned pine (soft wood).

Examples of soft wood trees are Douglas fir, pine, spruce, and cedar, poplar, aspen and alder. Soft woods require less time to dry, burn faster and are easier to ignite than hardwoods.

Examples of hardwood trees are oak, maple, apple, and birch. Hardwoods require more time to season, burn slower and are usually harder to ignite than soft woods.

The best wood fuel is a combination of soft wood and hardwood. Start the fire with soft wood; the fire will give off quick heat to bring the fireplace up to operating temperature, and then the hardwood can be added for slow, even heat and longer burn time.

Moisture

Regardless of which species of wood you burn, the single most important factor that effects the way your fireplace operates is the amount of moisture in the wood. The majority of the problems fireplace owners experience are caused by trying to burn wet, unseasoned wood.

Freshly cut wood can be as much water as it is wood, having a moisture content of around 50%. Imagine a wooden bucket that weighs about eight pounds. Fill it with a gallon of water, put it in the fireplace and try to burn it. This sounds ridiculous but that is exactly what you are doing if you burn unseasoned wood.

Seasoning

Seasoned firewood is nothing more than wood that is cut to size, split and air dried to a moisture content of around 20%. The time it takes to season wood varies from around nine months for soft woods to as long as eighteen months for hardwoods. The key to seasoning wood is to be sure it has been split, exposing the wet interior and increasing the surface area of each piece. A tree that was cut down a year ago and not split is likely to have almost as high a moisture content now as it did when it was cut.

The following guideline will ensure properly seasoned wood:

Stack the wood to allow air to circulate freely around and through the woodpile.

Elevate the woodpile off the ground to allow air circulation underneath.

The smaller the pieces, the faster the drying process. Any piece over 6 in. (152 mm) in diameter should be split.

Cover the top of the woodpile for protection from rain and snow. Avoid covering the sides and ends completely. Doing so may trap moisture from the ground and impede air circulation.

The problems with burning wet, unseasoned wood are twofold: First, you will receive less heat output from wet wood because it requires energy in the form of heat to evaporate the water trapped inside. This is wasted energy that should be used for heating your home. Secondly, this moisture evaporates in the form of steam which has a cooling effect in your fireplace and chimney system. When combined with tar and other organic vapors from burning wood it will form creosote which condenses in the relatively cool fireplace and chimney.

WARNING

Fire Risk

Do NOT burn wet or green wood.

Store wood in dry location.

Stack wood so both ends are exposed to air.

Wet, unseasoned wood can cause accumulation of creosote.

WARNING

Fire Risk

Do NOT store wood:

Closer than required clearances to combustibles to fireplace.

Within space required for loading or ash removal.

32

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

I. Starting a Fire

Check the flue damper to be certain it is in the full open position. Place crumpled or twisted paper under the fireplace grate. Loosely arrange kindling or small pieces of wood to form a layer above the paper.

The fires must be built on the fireplace grate, without danger of the burning fuel falling out of the fireplace opening.

Light the paper and add small pieces of wood until a hot bed of embers has been established.

After establishing the fire bed, and the small firewood is burning briskly, add a minimum of three average sized pieces of split firewood, place the wood in such a manner to allow combustion air and flames between them.

Note: When first lighting your fireplace, it may be necessary topre-warmthe flue to establish a draft. This is done by holding a rolled up piece of burning newspaper under the flue damper for a few moments. This will help reduce smoke spillage duringstart-up.

Note: The first three or four fires should be of moderate size to allow the oils and binders to be burned from the fireplace and the refractory and paint to cure. You may notice an industrial odor the first few fires. This is considered normal.

CAUTION

Odors and vapors released during initial operation.

Curing of high temperature paint.

Open windows for air circulation.

Odors may be irritating to sensitive individuals.

WARNING

Fire Risk

Keep combustible materials, gasoline and other flammable vapors and liquids clear of fireplace.

Do NOT store flammable materials close to the fireplace.

Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace.

Keep all such liquids well away from the fireplace while it is in use.

Combustible materials may ignite.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

33

Unsealed can lights?

10 Troubleshooting

This fireplace will operate correctly only if adequate ventilation is provided to allow proper draft to the fireplace system. Hearth & Home Technologies assumes no responsibility for the improper performance of the fireplace system caused by inadequate draft due to environmental conditions, down drafts, tight sealing construction of the structure, or mechanical exhausting devices which will create a negative air pressure within the structure where the fireplace is located.

A. Understanding Vent Problems

If smoke spillage occurs from a fireplace opening when the door is open and the proper chimney height, flue size, and configuration requirements for the installation have been met, there is either a leakage in the flue, a blockage in the

flue, or some condition is in effect to draw smoke from the fireplace into the house. Understanding and differentiating the conditions which can cause each of these kinds of spillage problems is essential to their solution.

Flue Leakage

Check for improperly connected flue joints or a damaged flue joint in the chimney system. Such leakage would reduce draft (air would be drawn in through the leaks rather than through the fireplace). The result might be difficult start-upand smoky fires that might spill if other adverse draft conditions accompany this problem.

Flue Blockage

The damper should be open.

Overhanging tree?

 

 

 

 

s

 

 

 

d

 

 

 

in

 

 

 

 

w

 

 

 

g

 

 

n

 

 

o

 

 

 

Str

 

 

 

 

a

r

o

 

 

 

 

y

 

 

 

ne

 

 

im

 

 

h

 

 

c

 

 

 

d

 

 

 

 

n

 

 

 

 

u

 

 

 

 

 

 

 

 

?

 

 

 

 

n

 

 

 

o

 

 

 

i

 

 

 

t

 

 

 

a

 

 

in

 

 

rm

 

 

 

te

 

 

 

 

Bird's nest or leaves in termination cap?

Another appliance in home also exhausting

air (furnace, fan, dryer, etc.)?

Overhead fan

operating?

Air register from furnace near fireplace?

Doors opening and closing? Window closed for start-up?

Structural

changes inchimney area?

Creosote buildupin flue?

Damper closed?

Outside air closed?

Figure 10.1 Factory-builtFireplaces: Troubleshooting

34

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

B. Diagnostics and Problem Solving

I can’t get a good fire going. What am I doing wrong?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Is the damper open?

• No draft

Open damper.

 

 

 

 

Is there enough paper/starter?

Insufficient heat to ignite kindling

Use more paper/starter.

 

 

 

 

Is there enough kindling?

Insufficient heat to ignite fuel

Use more dry kindling.

Is the kindling dry?

 

 

 

 

 

 

 

Is there enough or too much

Insufficient heat to establish draft

Use small split wood that is well seasoned (split, covered on top at

wood? Is it too large? Is it dry

Insufficient air passage

least 6 months, preferably a year).

enough?

 

Insufficient surface area

 

 

 

 

Ignition temperature high due to moisture

 

 

 

 

Are there adequate air spaces

• Insufficient combustion air and exposed

Arrange kindling and wood for air movement.

between fuel pieces?

 

surface area

 

 

 

 

 

Is the chimney pre-warmed?

Exposed, cold chimney down drafting

Use lighted rolled newspaper at throat or flue opening to start

 

 

 

upward movement.

 

 

 

Is there smoke in the house?

• Damper closed

Check damper; have chimney checked if it worked previously;

 

Obstruction in chimney

pre-warmchimney, shut off exhaust devices, open window slightly.

 

 

 

• Down draft from chimney temperature or

 

 

 

from negative house pressure

 

 

 

 

 

Does the kindling, wood not

Condition, amount, arrangement of kindling

Use more, drier, well-spacedkindling and fuel.

ignite?

 

and fuel

 

 

 

 

 

Does the kindling ignite, but the

Amount of kindling

Use more kindling; use smaller, dry wood.

fuel doesn’t?

Condition of fuel

 

 

 

 

 

 

 

Does the fuel ignite, but not

Condition of fuel

Use well-seasonedwood and sufficient amount; turn exhaust fans

burn well?

Draft problem

off; open window slightly. Perform Simplified House Pressure Test.

 

 

 

 

 

 

 

 

 

 

I don’t get enough/any heat from the fireplace. What can I do about it?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

How much wood is used for

Insufficient fuel

Make larger fires.

fire?

 

 

 

 

 

 

 

How well seasoned is the

Condition of fuel

Burn seasoned wood: covered on top, split and stacked for 9

wood?

 

 

months to 2 years.

 

 

 

 

Do you have a blower (where

Yes: Turning blower on too early or setting

Yes: Wait until fire established and leave on lower speed.

possible)?

 

too high, cooling firebox

No: Add blower if available.

 

 

No: Need for all heat boosts possible

 

 

 

 

 

How much heat output do you

Unrealistic expectations

Explanation of decorative nature of fireplace; suggestion of

expect?

 

 

approved fireplace insert.

 

 

 

 

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

35

The fireplace burns the wood too fast. What can I do?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Do you have glass doors?

Need to slow air intake

Add glass doors.

 

 

 

 

What is the condition of the

Extremely dry wood

Mix in less seasoned wood after fire established.

wood?

 

 

 

 

 

 

 

I smell smoke in the house during operation. What’s causing that?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Does the fire start and burn

No:

 

well?

• Damper not fully open

Open damper; check and clean chimney if needed; use adequate

 

 

Chimney obstruction

kindling and fuel; open glass doors or open window, check for

 

need for balanced air make-up.

 

Not enough kindling and/or fuel to establish

 

 

 

 

draft

 

 

Inadequate combustion air

 

 

Yes:

 

 

Fire too close to front

Build fire farther back. Do not use exhaust fans during startup

 

Competition with exhaust devices

and/or check for need for balanced air make-upsystem.

 

 

 

 

 

 

I smell smoke in the house after we’ve had a fire in the fireplace. What is the cause/what can we do?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Is the damper closed?

• No: Down draft or negative pressure

Close the damper at end of burn.

 

Yes: Negative pressure from exhaust fans

Check for need for glass doors. Check for need for balanced air

 

 

and/or house stack effect.

make-upsystem or raising chimney.

 

 

 

Is the chimney clean?

• No: Creosote odor

Have chimney cleaned.

 

Yes: Damper closed too early

Wait until fire completely out before closing damper.

 

 

 

 

36

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

11 Maintenance and Servicing the Fireplace

A. Disposal of Ashes

Ashes should be placed in a metal container with a tight-fit-ting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all embers have thoroughly cooled.

B. Chimney Inspection/Cleaning

Inspect the chimney internally for obstructions and construction damage. Flue pipe joints and seams must be continuous and mechanically tight.

The chimney should be inspected once every two months during the heating season.

If creosote has accumulated, it should be removed to reduce the risk of a chimney fire.

WARNING

Fire Risk

Disposal of ashes

Ashes should be placed in metal container with tight fitting lid.

Do not place metal container on combustible surface.

Ashes should be retained in closed container until all embers have thoroughly cooled.

WARNING

Fire Risk

Prevent creosote buildup

Inspect chimney once every two months during heating season.

Remove creosote to reduce risk of chimney fire.

Ignited creosote is extremely HOT.

Refer to Figure 11.1 to remove/reinstall termination caps.

C. Firebox Refractory

Check firebox refractory for excessive cracks or gaps. If cracks exceed 1/4 in. (6 mm) in width the refractory should be replaced. See Section 12 for replacement information.

WARNING

Fire Risk

Inspect fireplace refractory annually.

Crumbling, deteriorated refractory can allow overheating of surrounding materials.

Note: As you use the fireplace, expansion and contraction will cause minor cracking of the refractory. This is normal, unavoidable, and will not affect the performance of the fireplace. If the cracks become large enough that the metal behind the refractory is exposed or large pieces fall out, the panels should be replaced.

Remove 8 screws (9 for King), lift top cover.

Cap Top

Remove screws,

Remove 4 screws

(Be sure

lift top cover.

and lift top pan off.

holes in

Top Cover

 

cap top

 

 

 

and cap

 

 

base are

Cap

Cap

aligned.)

 

 

Cap Base

Chimney

 

 

 

 

 

Slip

 

 

Section

European Copper Series

TR344/TR342

ST375

Termination Cap

Round

Square

(CT-Kingshown)

Termination Cap

Termination Cap

1.Remove the 4 screws.

2.Remove the screen.

3.Remove the baffle.

Cap

Chase

Remove 2 screws from the front and back and lift the top off.

TS345/TS345P

TCT375

Square

Terra Cotta

Termination Caps

Termination Cap

Figure 11.1 Chimney & Termination Cap Cleaning

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

37

CAUTION

Handle glass assembly with care.

When cleaning glass door:

Avoid striking, scratching or slamming glass.

Do NOT use abrasive cleaners.

Use a hard water deposit glass cleaner on white film.

Do NOT clean glass when it is hot.

WARNING

Fire Risk

Do not use chimney cleaners or flame colorants in your fireplace.

Will corrode chimney.

WARNING

Asphyxiation Risk Fire Risk

Annual inspection by qualified technician recommended.

Check:

Condition of doors, surrounds and fronts

Condition of glass and glass assembly

Obstructions of combustion and ventilation air

Gas connections and fittings (if present)

Obstructions of termination cap

Refractory panels

Clean:

Glass

Air passageways, grilles

D. Maintenance Task List

Inspect

 

Maintenance Tasks

Screens

1.

Assess condition of screen and replace as necessary. Screens are required.

 

 

 

 

2.

Verify maintenance of proper clearance to combustible household objects.

 

 

 

Glass Doors

1.

Inspect glass panels for cracks. Replace if this condition is present.

 

 

 

 

2.

Confirm there is no damage to glass or glass frame. Replace as necessary.

 

 

 

 

3.

Clean glass using a non-abrasivecleaner such as Brasso©.

 

 

 

Circulation Compartment

1.

Remove any foreign objects.

 

 

 

 

2.

Verify unobstructed air circulation.

 

 

 

Firebox

1.

Inspect condition of refractory. Replace if crumbly, deteriorated, or if cracks exceed 1/4 in. (6 mm).

 

 

 

Chimney

1.

Inspect for blockage or obstruction such as bird nests, leaves, etc.

 

 

 

 

2.

Confirm that termination cap remains clear and unobstructed by plants, etc.

 

 

 

 

3.

Verify that termination cap clearance to subsequent construction (building additions) has been maintained.

 

 

 

 

4.

Inspect for corrosion or separation.

 

 

 

 

5.

Verify weather stripping, sealing and flashing remain intact.

 

 

 

 

6.

Inspect for creosote and remove as needed. (See Sections 10 and 11)

 

 

 

Grate

1.

If grate burns out, it should be replaced only with the grate specified on the rating plate and in the replacement

 

 

parts list for this fireplace.

E. Chimney Fire

In the event of a chimney fire:

Have the chimney and adjacent structure inspected by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of an NFPA 211 Level 2 inspection of the chimney.

Replace components of the chimney and fireplace as specified by the professionals.

Ensure all joints are properly engaged and the chimney is properly secured.

A chimney fire can permanently damage your chimney system. Failure to replace damaged components and make proper repairs creates risk of fire.

38

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

12 Reference Materials

A. Fireplace Dimensions

471/8"

 

 

 

 

20"

 

 

 

 

 

 

 

42"

22½"

42"

 

 

 

24"

 

 

 

22½"

11"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12"

36"

5¾"

½"

36"

5¾"

 

 

40"

40"

TOP VIEW - BOTH MODELS

FRONT VIEW - BAY-40

 

FRONT VIEW - PIER-40

 

 

 

 

 

 

 

 

5¼"

175/8"

 

 

 

 

 

12"

 

 

GAS

 

 

 

 

 

 

KNOCKOUT

 

 

 

 

471/8"

 

 

 

44"

 

 

 

 

 

 

8¾"

 

 

 

3"

 

8¼"

40"

 

 

 

 

 

 

 

 

 

GAS

 

 

 

9½"

 

 

KNOCKOUT

 

 

 

53/8"

7"

12"

 

24"

END VIEW - BAY-40

 

 

ELECTRICAL

 

 

 

 

 

KNOCKOUT

 

 

FOR ST36C

BOTTOM VIEW

END VIEW - PIER-40

BAY-40

 

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

39

B. Fireplace Components

Catalog #

Description

PIER-40

Peninsula Fireplace

BAY-40

Island Fireplace

 

 

DM1036

Glass Doors - bi-fold,Clear-View- Black

DM1036B

Glass Doors - bi-fold,Clear-View- Polished Brass

 

 

DM1036S

Glass Doors - bi-fold,Clear-View- Stainless Steel

DM1000

Fixed End Glass Panel, Clear-View- Black

DM1000B

Fixed End Glass Panel, Clear-View- Polished Brass

 

 

DM1000S

Fixed End Glass Panel, Clear-View- Stainless Steel

HX3

Hearth Extension

 

 

GR3

Integral Grate (included with Fireplace)

TK53B1

Trim Kit, Polished Brass Fireplace Perimeter (2 required)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bi-foldGlass Doors

(SIDE OF FIREPLACE)

GR3

Integral Grate AK17/AK18

Outside Air Kit

52 in.

(1321 mm)

16 in.

(406 mm)

1/2 in.

 

HX3 Hearth Extension

 

 

TK53B

 

(13 mm)

Trim Kit

40

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

C. Chimney Components

The following pictures show only those chimney components which may be safely used with this fireplace.

Catalog #

Description

CAK5A

Chimney Air Kit

 

 

ID4

Insulated Duct/Outside Air

UD4

Uninsulated Duct/Outside Air

 

 

SL1106

Chimney Section - 6 in. (152 mm) long

 

 

SL1112

Chimney Section - 12 in. (305 mm) long

SL1118

Chimney Section - 18 in. (457 mm) long

 

 

SL1136

Chimney Section - 36 in. (914 mm) long

SL1148

Chimney Section - 48 in. (1219 mm) long

 

 

SL11

Chimney Stabilizer

SL1130

Chimney Offset/Return - 30 deg

 

 

FS538

Ceiling Firestop - Straight

 

 

FS540

Ceiling Firestop - 30 deg

AS10

SL1100 Straight Attic Insulation Shield, 24 in. (610 mm)

 

 

JB577

Chimney Joint Band

CB576

Chimney Bracket

 

 

RF570

Roof Flashing - Flat to 6/12 Pitch

RF571

Roof Flashing - 6/12 to 12/12 Pitch

 

 

TR11

Round Termination Cap

TR11T

Round Telescoping Termination Cap

TCT1175

Terra Cotta Termination Cap

 

 

ST1175

Square Termination Cap

CT56

Chase Top

 

 

LDS33

Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)

LDS46

Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)

 

 

LDS-BV

Decorative Shroud - 26 in. x 26 in. (660 mm x 660 mm)

 

Field Constructed Shrouds (See “Woodburning

 

Termination Cap”)

CT11-King

European Copper Termination Cap - King Style

 

 

CT11-Queen

European Copper Termination Cap - Queen Style

CT11-Bishop

European Copper Termination Cap - Bishop Style

 

 

CT11-Knight

European Copper Termination Cap - Knight Style

CT11-Pawn

European Copper Termination Cap - Pawn Style

ID4 Insulated Duct

4 in. (102 mm) i

42 in.

(1067 mm)

UD4 Uninsulated Duct

4 in. (102 mm) i

42 in.

A

13 in.

11 in. (330 mm)

(279 mm)

B

Chimney Sections

 

A

 

 

B

Catalog #

in

 

mm

in

 

mm

SL1106

6

 

152

4-3/4

 

121

 

 

 

 

 

 

 

SL1112

12

 

305

10-3/4

 

273

SL1118

18

 

457

16-3/4

 

425

 

 

 

 

 

 

 

SL1136

36

 

914

34-3/4

 

883

SL1148

48

 

1219

46-3/4

 

1187

A = Actual Length

B = Effective Length (length of

chimney part after it has

been snapped to another)

14 in.

14 in.

 

(356 mm)

Inside

(356 mm)

20-3/4in.

Diameter

 

5-1/4in.

(527 mm)

11 in.

 

(279 mm)

(133 mm)

4 in. (102 mm)

 

13 in.

 

Outside Diameter

(330 mm)

 

13 in.

 

 

(330 mm)

CAK5A Chimney Air Kit

SL11 Chimney Stabilizer

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

41

 

 

Inside

 

 

Diameter

 

 

11 in.

 

 

(279 mm)

21 in.

 

Outside

(533 mm)

Diameter

 

 

 

 

13 in.

 

 

(330 mm)

 

SL1130 Offset/Return

Assembled

Diameter: 17 in./432 mm

Height: 24 in./610 mm

AS10 Straight Attic Insulation Shield

10-1/2in.

(267 mm)

2 in. (51 mm)

JB577 Chimney Joint Band

10-1/2in.(267 mm)

CB576 Chimney Joint Band

A

B

 

14-1/2in.

 

 

(368 mm)

 

Ceiling Firestop

 

 

 

 

 

 

 

Catalog #

A

 

B

FS538

0-deg.

17 in.

 

432 mm

FS540

30-deg.

26 in.

 

660 mm

15-1/4in.

(387 mm)

29 in.

25-1/4in.

(737 mm)

(641 mm)

RF570 Roof Flashing

15-1/4in.

(387 mm)

39-7/8in.

28 in.

(711 mm)

(1013 mm)

 

RF571 Roof Flashing

 

42

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

15-3/4in.

(400 mm)

TR11 Round Termination Cap

32-3/8in.

(822 mm)

34-3/8in.

(873 mm)

TR11T Round Telescoping Termination Cap

14-3/4in.

(375 mm)

23 in.

23 in.

(584 mm)

(584 mm)

 

ST1175 Square Termination Cap

20 in.(508 mm)

17 in.

 

(432 mm)

9-3/8in.

 

 

(238 mm)

9-1/4in.

(235 mm)

TCT1175 Terra Cotta Cap

72 in.

36 in.

(1829 mm)

(914 mm)

13-3/8in.

(340 mm)

2 in.

(51 mm)

CT56 Chase Top

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Decorative Shroud

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LDS33/LDS46

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

B

 

 

C

 

D

Catalog #

in.

 

 

 

mm

 

in.

 

mm

 

in.

 

mm

in.

 

mm

LDS33

36

 

 

 

914

 

36

 

914

 

8-1/2

 

216

11

 

279

LDS46

48

 

 

 

1219

 

72

 

1829

 

8-1/2

 

216

11

 

279

 

 

 

 

 

E

 

 

 

 

 

D

 

 

C

B

 

 

 

 

 

 

 

 

 

 

 

 

A

LDS-BVDecorative Shroud

 

 

Catalog #

A

B

C

D

E

in.

26

12-1/2

15-1/2

22

23

LDS-BV

660

318

394

533

584

mm

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

43

European Copper Caps

21 in.(533 mm)

18-1/4in.

(464 mm)

20-3/4in.

(527 mm)

47-3/4in.

(1213 mm) 41-1/8in.

(1045 mm)

38-5/8in.

(981 mm)

 

 

 

 

 

 

 

 

 

20 in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24 in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20 in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(508 mm)

 

 

 

 

(508 mm)

 

 

 

 

(610 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CT3-King

 

 

 

 

 

CT3-Queen

 

 

 

 

 

CT3-Bishop

16 in.

(406 mm)

21 in.

(533 mm)

38-3/8in.

(975 mm)

25-3/4in.

(654 mm)

 

16 in.

 

 

 

 

 

20-5/8in.

 

 

 

 

 

 

 

(406 mm)

 

 

 

(524 mm)

 

CT3-Knight

 

 

 

CT3-Pawn

44

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

Woodburning Termination Cap

Shroud

TS345 / 445

TR342 / 344

TR342 / 344 TV

TR11 / 11T

TR11 / 11T TV

(Top Vent)

TR442 / 444

TR442 / 444 TV

(with TR-TVKinstalled)

 

 

 

(with TR-TVKinstalled)

 

 

OPEN TOP with solid sides and 3 in. opening at the bottom.

Minimum Base Dimensions

 

28 X 28 with

 

32 X 32 with

 

23 X 23

26 X 26

Radiation

26 x 26

(Inches)

Radiation Shield

 

 

Shield

 

 

 

 

 

 

 

 

 

 

 

 

Minimum Top Dimensions

20 x 20

25 X 25

23 X 23

29 X 29

23 x 23

(Inches)

 

 

 

 

 

 

 

 

 

 

 

MAILBOX STYLE with open ends and 3 inch opening at the bottom of the sides.

Minimum Base Dimensions

 

26.5 X 28 with

 

34 X 34 with

28 X 30 with

N/A

28 X 30

Radiation

Radiation Shield or

(Inches)

Radiation Shield

 

 

Shield

34 X 34

 

 

 

 

 

 

 

 

 

 

Minimum Height (Inches)

N/A

28 1/4

27 1/2

28 1/4

27 1/2

 

 

 

 

 

 

ROOFED STYLE with12 X 22 (264 sq. in.) opening on each side and 3 in. space between the radiation shield and chase top.

Minimum Base Dimensions

 

27 X 27 with

27 X 27 with

34 X 34 with

34 X 34 with

N/A

Radiation

(Inches)

Radiation Shield

Radiation Shield

Radiation Shield

 

Shield

 

 

 

 

 

 

 

 

 

 

 

Minimum Height (Inches)

N/A

23

23

23

23

 

 

 

 

 

 

Minimum Height is measured from the bottom of the termination cap:

Minimum height is established with the bottom of the termination cap 7 in. above the chase top. Minimum height must increase accordingly for any height above 7 in.

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

45

D. Service Parts

Service Parts

BAY-40

 

 

 

Service Parts Diagram

Beginning Manufacturing Date: 2/4/04

Ending Manufacturing Date: Active

Multi-SidedWoodburning Fireplace

 

 

7

8

13

4

6

11

9

 

 

 

12

 

2

1

 

3

 

10

14

5

46

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

 

 

Service Parts

 

BAY-40

 

 

 

 

 

 

 

 

Service Parts List

Beginning Manufacturing Date: N/A

 

 

Multi-SidedWoodburning Fireplace

Ending Manufacturing Date: 08/01/01

 

 

 

 

 

 

#

 

Description of Part

 

Part Number

Qty.req.

1

Top Standoff

 

11864i

4

2

Starter Section Assembly

 

22072B

1

3

Damper Assembly

 

34515

1

4

Front Door Support

 

4012-035

1

5

Side Door Support

 

23954

2

6

Grate

 

GR3

1

7

End Retainer Assembly

 

13929A

2

8

Grate Retainer (for End Retainer Assembly)

 

13294B

4

9

Back Refractory

 

27856

1

10

Side Refractory

 

27857

2

11

Hearth Refractory

 

13213A

1

12

Front Ashlip

 

13214A

1

13

Left Side Ashlip

 

13827A

1

14

Right Side Ashlip

 

13828A

1

 

Nailing Flange

 

12692

4

 

Firescreen Rod

 

11866B

2

 

Firescreen Assembly

 

12267

2

 

Screen Handle

 

4021-149

1ea.

 

Damper Control

 

13229

1

 

Damper Weight

 

19785A

1

 

Door Track (for bottom)

 

4012-002

1

 

Door Track (for top)

 

15425

1

 

Grate Retainer

 

13834B

2

 

Side Refractory Bracket

 

13831C

2

 

Refractory Bracket

 

13896B

2

 

Outside Air Door Assembly

 

13268A

1

 

Air Kit

 

AK17

1

 

Fastener Pack

 

12010B

1

 

Plate Assembly

 

19081A

1

 

Long Cable Tie

 

19954A

2

 

Air Kit Installation Instructions

 

31168

1

 

Outside Air Shield

 

33271

1

 

Strip Protector

 

18320

4

 

BAY-40Installation Instructions and Owner’s Manual

 

34977

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

47

Service Parts

PIER-40

 

 

Service Parts Diagram

Beginning Manufacturing Date: N/A

Ending Manufacturing Date: Active

Multi-SidedWoodburning Fireplace

 

3

2

1

9

10

11

13

6

7

12

 

8

5

4

14

48

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

 

 

Service Parts

 

PIER-40

 

 

 

 

 

 

 

 

 

Service Parts List

Beginning Manufacturing Date: N/A

 

 

Ending Manufacturing Date: Active

 

 

Multi-SidedWoodburning Fireplace

 

 

 

 

 

 

 

 

 

 

 

 

#

Description of Part

 

PIER-40

Qty.

 

1

Ashlip

 

13214A

2

 

2

Back Refractory

 

13319

1

 

 

Corner Refractory

 

13320A

2

 

 

Damper Blade Assembly

 

13227

1

 

 

Damper Control

 

13229

1

 

 

Damper Rod

 

13230A

1

 

3

Door Track Support

 

12757

4

 

4

End Ashlip

 

13215A

1

 

5

End Door Support

 

23954A

1

 

6

End Lower Front Face (overlay only) - pre 14/95

 

13234B

1

 

6

End Lower Front Face (overlay only) - post 15/95

 

23950A

1

 

7

End Top Front Face (overlay only) - pre 14/95

 

13254F

1

 

7

End Top Front Face (overlay only) - post 15/95

 

23911A

1

 

8

End Upper Front Face (overlay only) - pre 14/95

 

13233C

1

 

8

End Upper Front Face (overlay only) - post 15/95

 

23949A

1

 

9

Firescreen Assembly - pre 22/97

 

11855A

4

 

9

Firescreen Assembly - post 23/97

 

12267

4

 

 

Heat & Glo Logo Screen Handle

 

4021-149

4

 

 

Firescreen Rod

 

11866B

4

 

10

Grate

 

GR3

1

 

 

Hairpin Clips

 

101025

4

 

 

Hearth Refractory

 

13321B

1

 

 

Installation Instructions

 

17920

1

 

11

Lower Front Face (overlay only) - pre 14/95

 

12847B

2

 

11

Lower Front Face (overlay only) - post 15/95

 

23942

2

 

 

Nailing Flange

 

12692

4

 

12

Outside Air Kit

 

13330

1

 

 

Refractory Retainer

 

11847C

1

 

13

Side Smoke Shield

 

13238C

1

 

14

Starter Section

 

22072B

1

 

15

Top Front Face (overlay only) - pre 14/95

 

13263G

2

 

15

Top Front Face (overlay only) - post 15/95

 

23953

2

 

16

Top Standoff

 

11864i

4

 

17

Upper Front Face (overlay only) - pre 14/95

 

13232C

2

 

17

Upper Front Face (overlay only) - post 15/95

 

22937B

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

49

This page intentionally left blank.

50

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

E. Limited Warranty

WARRANTY

FOR HEAT & GLO FIREPLACES

The limited warranty will not become effective until you have mailed the completed warranty card to:

Hearth & Home Technologies Inc.

20802 Kensington Blvd., Lakeville, MN 55044.

This card must be mailed within 60 days of the fireplace installation.

Subject to the conditions set forth herein, HEARTH & HOME TECHNOLOGIES INC. (HHT) extends the following limited warranty with respect to your Heat & Glo fireplace, excluding accessories, chimney components and glass doors.

If HHT is satisfied that any part or portion of the fireplace covered by this warranty is defective in material or workmanship under normal use and service as described in the operating instructions, HHT will take the following actions:

1.Within the first five (5) years from the date of installation, HHT shall, at its option, replace or repair any such defect in material or workmanship, at HHT’s expense. HHT SHALL NOT BE RESPONSIBLE FOR ANY OTHER LABOR COSTS, OR EXPENSES, INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

2.During the sixth (6th) through the (10th) years after the date of installation, HHT shall supply replacement parts or parts at no charge, but SHALL NOT BE RESPONSIBLE FOR ANY LABOR, TRANSPORTATION, OR OTHER INDIRECT DAMAGES.

3.During the eleventh (11th) through the fifteenth (15th) years after date of installation, HHT will send to you, FOB its factory, replacement parts (if available) at the current minimum wholesale price, but HHT SHALL NOT BE RESPONSIBLE FOR ANY LABOR, TRANSPORTATION OR OTHER INDIRECT DAMAGES.

4.During the first six (6) months after installation, HHT shall, at its option, replace or repair the glass doors and any electrical components, if operation is faulty. (This does not include glass panels broken during shipment, misuse or careless handling.) After the first six (6) months, HHT will sell to you, FOB its factory, replacement parts at the current list price, but HHT SHALL NOT BE RESPONSIBLE FOR ANY LABOR, TRANSPORTATION OR OTHER INDIRECT DAMAGES. IF GLASS DOORS OTHER THAN FACTORY DOORS ARE USED ALL WARRANTY AND LIABILITY ON THE FIREPLACE IS VOIDED.

HHT may discharge its entire warranty liability by refunding the price of the product.

Products made by other manufacturers, sold with the fireplace or thereafter are not covered by this limited warranty.

This limited warranty will be void if the fireplace is not installed according to the installation instructions. The limited warranty also is void if the fireplace is not operated, at all times, according to the operating instructions furnished. The limited warranty will also be void if the fireplace is removed from the place originally installed.

EXCEPT TO THE EXTENT PROVIDED BY LAW, NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND NO IMPLIED WARRANTIES SHALL APPLY TO THE FIREPLACE AFTER THE ABOVE LIMITED WARRANTY HAS EXPIRED.

In states that do not allow limitations on how long implied warranty lasts, or do not allow exclusion of indirect damages, those limitations or exclusions may not apply to you. You may also have additional rights not covered in this limited warranty.

HHT reserves the right to make changes at anytime, without notice, in design, material, specifications and prices and the right to discontinue styles and products.

Feb 2006

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07

51

¨F. Contact Information

Please contact your Heat & Glo dealer with any questions or concerns.

For the number of your nearest Heat & Glo dealer, please visit www.heatnglo.com.

– NOTES –

CAUTION

DO NOT DISCARD THIS MANUAL

• Important operating •

Read, understand

• Leave this manual with

a n d m a i n t e n a n c e

and follow these

party responsible for

instructions included.

instructions for safe

use and operation.

 

i n s t a l l a t i o n a n d

 

 

operation.

 

DO DISCARDNOT

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

52

Heat & Glo • Multi-SidedWoodburning Fireplace • 34977 Rev T • 11/07