Heat & Glo LifeStyle AT-GRAND User Manual

Size:
515.33 Kb
Download

Step 9

Before Lighting

the Appliance

Step 10

Lighting the

Appliance

After the

Installation

Before lighting the appliance, be sure to do the following:

Review safety warnings and cautions

Read the Safety and Warning Informationsection at the beginning of this Installers Guide.

Double-checkfor gas leaks

Before lighting the appliance, double-checkthe unit for possible gas leaks.

Double-checkvent terminations and front grilles for obstructions.

Before lighting the appliance, double-checkthe unit for possible obstructions that could be blocking the vent terminations or the front grilles.

Double-checkfor faulty components

Any component that is found to be faulty MUST BE replaced with an approved component. Tampering with the appliance components isDANGEROUS and voids all warranties.

A small amount of air will be in the gas supply lines. When first lighting the appliance, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the appliance will light and will operate normally.

Subsequent lightings of the appliance will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

You’ve reviewed all safety warnings, you’ve checked the appliance for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the appliance.

WARNING

PLEASE REFER TO THE USER’S

MANUAL FOR ALL CAUTIONS, SAFETY,

AND WARNING INFORMATION

PERTAINING TO THE LIGHTING AND

OPERATION OF THE APPLIANCE.

LEAVE THIS INSTALLATION MANUAL

WITH THE APPLIANCE FOR FUTURE REFERENCE.

18

4

Maintaining and Servicing Your Appliance

19

Appliance

Maintenance

Although the frequency of servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance check-upat the beginning of each heating season. See the table below for specific guidelines regarding each maintenance task.

IMPORTANT

TURN OFF THE GAS BEFORE SERVICING

 

 

YOUR APPLIANCE.

 

 

 

 

 

Type of

 

 

 

 

Fireplace

 

 

 

Fireplace Maintenance Task To

Maintenance

 

Frequency

By

Be Completed

 

 

 

 

Replacing

Once annually,

Qualified

Brush away loose ember material near

Old Ember

during the

Service

the burner. Replace old ember

Material

annual check-up

Technician

material with new dime-sizeand-shape

 

 

 

 

pieces of Golden Ember (GE-93)and

 

 

 

 

Glowing Ember (050-721).New ember

 

 

 

 

material should be placed alternately on

 

 

 

 

top of the burner—alayer of Golden

 

 

 

 

Ember, a layer of Glowing Ember,

 

 

 

 

and so on. Save the remaining ember

 

 

 

 

material and repeat this procedure at

 

 

 

 

your next servicing. For more

 

 

 

 

information, see Placing Ember

 

 

 

 

Material in the INSTALLERS GUIDE.

 

 

 

 

Cleaning

Once annually

Qualified

Brush or vacuum the control

Burner

 

 

Service

compartment, fireplace logs, and

& Controls

 

 

Technician

burner areas surrounding the logs.

 

 

 

 

Checking

Periodically

Qualified

Make a visual check of your fireplace’s

Flame

 

 

Service

flame patterns. Make sure the flames

Patterns,

 

 

Technician/

are steady—notlifting or floating. See

Flame Height

 

 

Owner

the picture in Figure 14. The flame

 

 

 

 

sensor(DSI) or thermopile/thermocouple

 

 

 

 

(standing pilot) tips should be covered

 

 

 

 

with flame. See the picture in Figure15.

 

 

 

 

Checking

Before initial use

Qualified

Inspect the external vent cap on a

Vent System

and at least

Service

regular basis to ensure that no debris is

 

annually thereafter,

Technician/

interfering with the flow of air. Inspect

 

more frequently

Owner

venting system for proper function.

 

if

possible

 

 

 

 

 

 

Cleaning

As necessary

Homeowner

Clean as necessary, particularly after

Glass Door

 

 

 

adding new ember (flame colorant)

 

 

 

 

material. Film deposits on the inside of

 

 

 

 

the glass door should be cleaned off

 

 

 

 

using a household glass cleaner.

 

 

 

 

NOTE: DO NOT handle or attempt to

 

 

 

 

clean the door when it is hot and

 

 

 

 

DO NOT use abrasive cleaners.

 

 

 

 

 

MAKE SURE THE FLAMES

ARE STEADY—NOT

LIFTING OR FLOATING.

Figure 14. Burner Flame Patterns

STANDING PILOT

3/8" (10 mm)

Figure 15. Pilot/Ignitor Flame Patterns

20

5

 

All parts listed in this INSTALLERS GUIDE may be

 

ordered from an authorized dealer. When requesting

 

service or replacement parts for your appliance, please

 

provide the model number and the serial number.

Standing Pilot Only

 

PART

PART DESCRIPTION

PART NUMBER

 

Valve LP

SRV60–523

 

Valve NG

SRV60–522

Replacement

 

 

 

Parts and

 

 

 

Accessories

 

Piezo Ignitor

SRV418-513

 

 

Thermopile

SRV60–512

 

 

Thermocouple

SRV446-511

 

 

Pilot Orifice LP

SRV446–517

 

 

Pilot Orifice NG

SRV446–505

 

 

Pilot Assembly LP

SRV485-511A

 

 

Pilot Assembly NG

SRV485-510A

 

 

Pilot Tube

SRV446-301

 

 

Burner Tube

SRV438-300

21

Standing Pilot Continued

PART

PART DESCRIPTION

PART NUMBER

 

Burner

SRV475-328A

Burner Orifice NG

SRV57-800

Burner Orifice LP

SRV60-801

Rotory Switch

SRV436-525A

Glass Door Assembly

GLA-ATG

Grate Assembly

SRV475-360A

Refractory

SRV459-337

22

Standing Pilot (Cont.)

PA R T

PA R T

PAR T N U M B E R

D E S C R IP T IO N

 

 

 

Trim D oor

D F -ATG

 

Log #1

S RV 446 -701

 

Log #2

S RV 446 -702

 

Log #3

S RV 446 -703

 

Log #4

S RV 446 -704

 

Log #5

S RV 446 -705

 

Log #6

S RV 446 -706

Accessories

ACCESSORY

PART DESCRIPTION

PART NUMBER

 

Remote Control Kit

RCH-09A

 

 

RC-SMART

 

 

RC-SMART

 

 

SMART-STAT

 

 

SMART-STAT

 

 

RC-MLT

 

 

RC-MLT

 

Wall Switch Kit

 

 

- Off White

WSK-21

 

- White

WSK-21-W

23