Heat & Glo LifeStyle 8000CMOD-IPI User Manual

Size:
4.17 Mb
Download

Owner’s Manual

Installation and Operation

Models: 6000CMOD-IPI8000CMOD-IPI

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

• Leave this manual

and maintenance

these instructions for safe

party responsible for

instructions included.

installation and operation.

and operation.

DO DISCARDNOT

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-DO NOT try to light any appliance.

-DO NOT touch any electrical switch.DO NOT use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualified personnel. Hearth & Home Technologies suggests NFI certified or factory trained professionals, or technicians supervised by an NFI certified professional.

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

1

NATURAL GAS

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas fireplace, an elegant and clean alternative to wood burning fireplaces. The Heat & Glo gas fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas fireplace will give you years of durable use and trouble-freeenjoyment. Welcome to the Heat & Glo family of fireplace products!

Homeowner Reference Information

We recommend that you record the following pertinent information about your fireplace.

Model Name: ___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on fireplace: _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Listing Label Information/Location The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.

Type of Gas

Gas and Electric

Information

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

Not for use with solid fuel.

(Ne doit pas entre utilise avec un combustible solide).

Type of Gas(Sorte De Gaz): This appliance must be installed in accordance with local codes, if any;if not, follow ANSI Z223.1in the USAor CAN/CGA B149 installation codes.(Installer l’appareil selon les codes ou reglements locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)

ANSI Z21XX-XXXX· CSA2.XX-MXX· UL307B

Minimum Permissible Gas Supply for Purposes of Input Adjustment.

 

 

 

Approved Minimum(De Gaz) Acceptable

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Pressure (Pression)

 

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Maximum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Minimum Manifold Pressure(Pression)

0.0 in w.c.

(Po. Col. d’eau)

 

 

 

Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes

MADE IN USA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN CANADA

 

Model:

XXXXXXXX

 

ALTITUDE:

0-0000FT.

0000-0000FT.

 

(Modele):

 

MAX. INPUT BTUH:

00,000

00,000

 

 

 

 

 

 

 

MIN. INPUT BTUH:

00,000

00,000

 

Serial

XXXXXXXX

 

ORIFICE SIZE:

#XXXXX

#XXXXX

 

 

 

(Serie):

 

Model Number

Serial Number

2

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Safety Alert Key:

DANGER! Indicates a hazardous situation which, if not avoidedwill result in death or serious injury.

WARNING! Indicates a hazardous situation which, if not avoidedcould result in death or serious injury.

CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 7 C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7 E. Non-CombustibleMaterials Specification. . . . . . . . . . . . . . 7 F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 7 G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 H. Requirements for the Commonwealth of Massachusetts. . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10 F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 G. Remote Controls, Wall Controls and Wall Switches. . . . . 10 H. IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . 11

I. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 11 J. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 11 K. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 12 L. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 M. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 13

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . .14

B. Maintenance Tasks-QualifiedService Technician . . . . . . 14

C. Glass Refractory, Base Pan, Burner and Valve

Assembly Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

D. Burner Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 18

B. Design and Installation Considerations . . . . . . . . . . . . . . 19

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 19

D. Inspect Appliance and Components. . . . . . . . . . . . . . . . . 19

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 20

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 21

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 22

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 23

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 32 B. Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 32 C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 33 D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 34 E. Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . . . . 34

9 Appliance Preparation

A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

B. Installing the Non-combustibleBoard. . . . . . . . . . . . . . . . 36

C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 36

10 Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . . 37 B. Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 38 C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 38 D. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 39 E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 39 F. Install Decorative Ceiling Components (SLP only). . . . . . 40 G. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 41 H. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 41 I. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 42 J. Install Decorative Wall Components (SLP only). . . . . . . . 42 K. Heat Shield Requirements for Horizontal Termination . . . 42 L. Install Horizontal Termination Cap (DVP and SLP Pipe) . 43

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 44

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 B. IntelliFire PlusTM Ignition System Wiring. . . . . . . . . . . . . . 45 C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 45 D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 46 E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 46 F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 46

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

3

13 Finishing

A. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 47

B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

C. Finish and Sealing Joints . . . . . . . . . . . . . . . . . . . . . . . . . 48

D. Door Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 52 B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 52 C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 E. Glass Panel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 52 F. Media Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 H. Install Trim and/or Surround. . . . . . . . . . . . . . . . . . . . . . . 55 I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

15 Troubleshooting

A. IntelliFire PlusTM Ignition System . . . . . . . . . . . . . . . . . . . 56

16 Reference Materials

A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 58

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 60

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

= Contains updated information.

4

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

B. Limited Lifetime Warranty

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

 

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

Parts

Labor

Gas

Wood

 

Pellet

EPA

Coal

Electric

Venting

Components Covered

 

 

 

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

 

 

1 Year

X

X

 

X

X

X

X

X

covered by Conditions,

 

 

 

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

 

 

2 years

 

 

 

 

 

and glass

 

 

 

 

 

 

 

 

 

 

 

 

X

X

 

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 years

 

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

 

X

X

 

 

 

Manifold tubes,

 

 

 

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

 

Burners, logs and refractory

 

 

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

 

X

X

X

 

 

Firebox and heat exchanger

 

 

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

 

X

X

X

X

X

All replacement parts

 

 

 

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

 

4021-645C12-29-10

 

 

 

 

 

 

 

 

Page 1 of 2

 

 

 

 

Heat & Glo •

6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

5

B. Limited Lifetime Warranty (continued)

WARRANTY CONDITIONS:

7KLV ZDUUDQW\ RQO\ FRYHUV ++7 DSSOLDQFHV WKDW DUH SXUFKDVHG WKURXJK DQ ++7 DXWKRUL]HG GHDOHU RU GLVWULEXWRU $ OLVW RI ++7 DXWKRUL]HG GHDOHUV LV DYDLODEOH RQ WKH ++7 EUDQGHG ZHEVLWHV

7KLV ZDUUDQW\ LV RQO\ YDOLG ZKLOH WKH ++7 DSSOLDQFH UHPDLQV DW WKH VLWH RI RULJLQDO LQVWDOODWLRQ

&RQWDFW \RXU LQVWDOOLQJ GHDOHU IRU ZDUUDQW\ VHUYLFH ,I WKH LQVWDOOLQJ GHDOHU LV XQDEOH WR SURYLGH QHFHVVDU\ SDUWV FRQWDFW WKH QHDUHVW ++7 DXWKRUL]HG GHDOHU RU VXSSOLHU $GGLWLRQDO VHUYLFH IHHV PD\ DSSO\ LI \RX DUH VHHNLQJ ZDUUDQW\ VHUYLFH IURP D GHDOHU RWKHU WKDQ WKH GHDOHU IURP ZKRP \RX RULJLQDOO\ SXUFKDVHG WKH SURGXFW

&KHFN ZLWK \RXU GHDOHU LQ DGYDQFH IRU DQ\ FRVWV WR \RX ZKHQ DUUDQJLQJ D ZDUUDQW\ FDOO 7UDYHO DQG VKLSSLQJ FKDUJHV IRU SDUWV DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

WARRANTY EXCLUSIONS:

7KLV ZDUUDQW\ GRHV QRW FRYHU WKH IROORZLQJ

&KDQJHV LQ VXUIDFH ILQLVKHV DV D UHVXOW RI QRUPDO XVH $V D KHDWLQJ DSSOLDQFH VRPH FKDQJHV LQ FRORU RI LQWHULRU DQG H[WHULRU VXUIDFH ILQLVKHV PD\ RFFXU 7KLV LV QRW D IODZ DQG LV QRW FRYHUHG XQGHU ZDUUDQW\

'DPDJH WR SULQWHG SODWHG RU HQDPHOHG VXUIDFHV FDXVHG E\ ILQJHUSULQWV DFFLGHQWV PLVXVH VFUDWFKHV PHOWHG LWHPV RU RWKHU H[WHUQDO VRXUFHV DQG UHVLGXHV OHIW RQ WKH SODWHG VXUIDFHV IURP WKH XVH RI DEUDVLYH FOHDQHUV RU SROLVKHV

5HSDLU RU UHSODFHPHQW RI SDUWV WKDW DUH VXEMHFW WR QRUPDO ZHDU DQG WHDU GXULQJ WKH ZDUUDQW\ SHULRG 7KHVH SDUWV LQFOXGH SDLQW ZRRG SHOOHW DQG FRDO JDVNHWV ILUHEULFNV JUDWHV IODPH JXLGHV OLJKW EXOEV EDWWHULHV DQG WKH GLVFRORUDWLRQ RI JODVV

0LQRU H[SDQVLRQ FRQWUDFWLRQ RU PRYHPHQW RI FHUWDLQ SDUWV FDXVLQJ QRLVH 7KHVH FRQGLWLRQV DUH QRUPDO DQG FRPSODLQWV UHODWHG WR WKLV QRLVH DUH QRW FRYHUHG E\ WKLV ZDUUDQW\

'DPDJHV UHVXOWLQJ IURP IDLOXUH WR LQVWDOO RSHUDWH RU PDLQWDLQ WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK WKH LQVWDOODWLRQ

 

LQVWUXFWLRQV RSHUDWLQJ LQVWUXFWLRQV DQG OLVWLQJ DJHQW LGHQWLILFDWLRQ ODEHO IXUQLVKHG ZLWK WKH DSSOLDQFH IDLOXUH WR

 

LQVWDOO WKH DSSOLDQFH LQ DFFRUGDQFH ZLWK ORFDO EXLOGLQJ FRGHV VKLSSLQJ RU LPSURSHU KDQGOLQJ LPSURSHU RSHUD-

 

WLRQ DEXVH PLVXVH FRQWLQXHG RSHUDWLRQ ZLWK GDPDJHG FRUURGHG RU IDLOHG FRPSRQHQWV DFFLGHQW RU LPSURSHUO\

 

LQFRUUHFWO\ SHUIRUPHG UHSDLUV HQYLURQPHQWDO FRQGLWLRQV LQDGHTXDWH YHQWLODWLRQ QHJDWLYH SUHVVXUH RU GUDIWLQJ

 

FDXVHG E\ WLJKWO\ VHDOHG FRQVWUXFWLRQV LQVXIILFLHQW PDNH XS DLU VXSSO\ RU KDQGOLQJ GHYLFHV VXFK DV H[KDXVW IDQV RU

 

IRUFHG DLU IXUQDFHV RU RWKHU VXFK FDXVHV XVH RI IXHOV RWKHU WKDQ WKRVH VSHFLILHG LQ WKH RSHUDWLQJ LQVWUXFWLRQV

 

LQVWDOODWLRQ RU XVH RI FRPSRQHQWV QRW VXSSOLHG ZLWK WKH DSSOLDQFH RU DQ\ RWKHU FRPSRQHQWV QRW H[SUHVVO\ DXWKRUL]HG

 

DQG DSSURYHG E\ ++7 PRGLILFDWLRQ RI WKH DSSOLDQFH QRW H[SUHVVO\ DXWKRUL]HG DQG DSSURYHG E\ ++7 LQ ZULWLQJ

 

DQG RU LQWHUUXSWLRQV RU IOXFWXDWLRQV RI HOHFWULFDO SRZHU VXSSO\ WR WKH DSSOLDQFH

 

1RQ ++7 YHQWLQJ FRPSRQHQWV KHDUWK FRPSRQHQWV RU RWKHU DFFHVVRULHV XVHG LQ FRQMXQFWLRQ ZLWK WKH DSSOLDQFH

 

$Q\ SDUW RI D SUH H[LVWLQJ ILUHSODFH V\VWHP LQ ZKLFK DQ LQVHUW RU D GHFRUDWLYH JDV DSSOLDQFH LV LQVWDOOHG

++7¶V REOLJDWLRQ XQGHU WKLV ZDUUDQW\ GRHV QRW H[WHQG WR WKH DSSOLDQFH¶V FDSDELOLW\ WR KHDW WKH GHVLUHG VSDFH ,QIRUPDWLRQ LV SURYLGHG WR DVVLVW WKH FRQVXPHU DQG WKH GHDOHU LQ VHOHFWLQJ WKH SURSHU DSSOLDQFH IRU WKH DSSOLFDWLRQ &RQVLGHUDWLRQ PXVW EH JLYHQ WR DSSOLDQFH ORFDWLRQ DQG FRQILJXUDWLRQ HQYLURQPHQWDO FRQGLWLRQV LQVXODWLRQ DQG DLU WLJKWQHVV RI

WKH VWUXFWXUH

This warranty is void if:

7KH DSSOLDQFH KDV EHHQ RYHU ILUHG RU RSHUDWHG LQ DWPRVSKHUHV FRQWDPLQDWHG E\ FKORULQH IOXRULQH RU RWKHU GDPDJLQJ FKHPLFDOV 2YHU ILULQJ FDQ EH LGHQWLILHG E\ EXW QRW OLPLWHG WR ZDUSHG SODWHV RU WXEHV UXVW FRORUHG FDVW LURQ EXEEOLQJ FUDFNLQJ DQG GLVFRORUDWLRQ RI VWHHO RU HQDPHO ILQLVKHV

7KH DSSOLDQFH LV VXEMHFWHG WR SURORQJHG SHULRGV RI GDPSQHVV RU FRQGHQVDWLRQ

7KHUH LV DQ\ GDPDJH WR WKH DSSOLDQFH RU RWKHU FRPSRQHQWV GXH WR ZDWHU RU ZHDWKHU GDPDJH ZKLFK LV WKH UHVXOW RI EXW QRW OLPLWHG WR LPSURSHU FKLPQH\ RU YHQWLQJ LQVWDOODWLRQ

LIMITATIONS OF LIABILITY:

7KH RZQHU¶V H[FOXVLYH UHPHG\ DQG ++7¶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

4021-645C12-29-10

Page 2 of 2

6

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

1 Listing and Code Approvals

A. Appliance Certification

 

C. BTU Specifications

 

 

 

 

 

 

 

 

 

 

 

 

Models

Maximum

Minimum

Orifice

 

 

 

 

 

Input

Input

Size

MODELS: 6000CMOD-IPI,8000CMOD-IPI

 

(U.S. or Canada)

 

BTU/h

BTU/h

(DMS)

 

 

 

 

LABORATORY: Underwriters Laboratories, Inc. (UL)

 

 

US

 

28,000

19,000

40

TYPE: Direct Vent Gas Appliance Heater

 

6000CMOD-IPI

(0-2000FT)

 

 

 

 

 

 

 

 

 

 

STANDARD: ANSIZ21.50b-2009• CSA2.22b-2009

 

(NG)

CANADA

 

25,200

17,100

41

 

 

(2000-4500FT)

 

 

 

 

US

 

20,000

14,000

55

 

 

6000CMOD-IPI

(0-2000FT)

 

This product is listed to ANSI standards for “Vented Gas

 

 

 

 

 

 

(LP)

CANADA

 

18,000

12,000

56

Appliance Heaters” and applicable sections of “Gas Burn-

 

 

 

 

(2000-4500FT)

 

ing Heating Appliances for Manufactured Homes and

 

 

 

 

 

 

 

 

 

US

 

32,000

22,000

35

Recreational Vehicles”, and “Gas Fired Appliances for

 

8000CMOD-IPI

(0-2000FT)

 

 

 

 

 

 

Use at High Altitudes”.

 

(NG)

CANADA

 

28,800

19,800

36

 

 

 

(2000-4500FT)

 

 

 

 

NOTICE: This installation must conform with local codes.

 

8000CMOD-IPI

US

 

22,000

15,000

54

 

(0-2000FT)

 

 

 

 

 

 

In the absence of local codes you must comply with the

 

(LP)

 

 

 

 

 

 

CANADA

 

20,000

14,000

55

National Fuel Gas Code, ANSI Z223.1-latestedition in

 

 

(2000-4500FT)

 

 

 

 

 

 

 

the U.S.A. and the CAN/CGA B149 Installation Codes in

D. High Altitude Installations

 

 

Canada.

 

 

 

NOTICE: If the heating value of the gas has been reduced,

 

these rules do not apply. Check with your local gas utility

 

or authorities having jurisdiction.

 

 

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

 

 

When installing above 2000 feet

elevation:

 

This appliance is tested and approved as either supplemen-

 

• In the USA: Reduce input rate 4% for each 1000 feet

tal room heat or as a decorative appliance. It should not be

factored as primary heat in residential heating calculations.

 

above 2000 feet.

 

 

 

 

 

• In CANADA: Reduce input rate 10% for elevations

 

B. Tempered Glass Specifications

 

between 2000 feet and 4500 feet. Above 4500 feet,

 

consult local gas utility.

 

 

 

 

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the requirements of ANSI Z97.1 andCPSC 16 CFR 1202

(Safety Glazing Certification Council SGCC# 1595 and1597. Architectural Testing, Inc. Reports02-31919.01 and

02-31917.01).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to15 U.S. Code(USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

Check with your local gas utility to determine proper orifice size.

E. Non-CombustibleMaterials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric Code CSA

C22.1.

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

7

Note: The following requirements reference various Massachusetts and national codes not contained in this document.

H.Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-upis installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-upmay be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half(1/2) in. in size,“GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

Detailed instructions for the installation of the venting system design or the venting system components; and

A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

8

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

2 Operating InstructionsUser Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

WARNING! Choking Hazard! Keep media out of reach of children.

If you expect that small children or vulnerable adults may come into contact with this fireplace, the following precautions are recommended:

Install a physical barrier such as:

-A decorative firescreen.

-Adjustable safety gate.

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

Never leave children alone near a hot fireplace, whether operating or cooling down.

Teach children to NEVER touch the fireplace.

Consider not using the fireplace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/safety-information.

To prevent unintended operation when not using your fireplace for an extended period of time (summer months, vacations, trips, etc):

Remove batteries from remote controls.

Turn off wall controls.

Unplug 6 volt transformer plug and remove batteries on IPI models.

B. Your Fireplace

WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire or injury.

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

FIXED GLASS ASSEMBLY

(NOT SHOWN)

SECTION 14.G.

MANTEL

SECTION 5.D

FAN KIT

SECTION 2.C.

HEARTH

CLEAR SPACE

SECTION 2.D.

Figure 2.1 General Operating Parts

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

9

C. Fan Kit (optional)

If desired, a fan kit may be added. Contact your dealer to order the correct fan kit.

D. Clear Space

WARNING! DO NOT place combustible objects in front of the fireplace or block louvers. High temperatures may start a fire. See Figure 2.2.

Avoid placing candles and other heat-sensitiveobjects on mantel or hearth. Heat may damage these objects.

 

3

FT.

CLEAR

 

 

 

 

IN

 

 

 

FRONT OFSPACE

 

 

 

FIREPLACE

Figure 2.2

Clear Space

 

E. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

F. Fixed Glass Assembly

See Section 14.G.

G.Remote Controls, Wall Controls and Wall Switches

Follow the instructions supplied with the control installed to operate your fireplace.

For specific information on fireplace controls, see Section 12. For safety:

Install a switch lock or a wall/remote control with child protection lockout feature.

Keep remote controls out of reach of children.

See your dealer if you have questions.

10

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

H. IPI Battery Tray/Battery Installation

The IntelliFire PlusTM system has a battery backup option. Battery longevity and performance will be affected by the service temperatures of this appliance.

NOTICE: Batteries should only be used as a power source in the event of an emergency such as an outage.

I. Control Module Operation

1.The control module has an ON/OFF/REMOTE selector switch that must be set. See Figure 2.3.

OFF Position: Appliance will ignore all power inputs and will not respond to any commands from a wall switch or remote. The unit should be in the OFF position during installation, service, battery installation, fuel conversion, and in the event that the control goes into LOCK-OUTmode as a result of an error code.

ON Position: Appliance will ignite and run continuously in the HI flame setting, with no adjustment in flame output. This mode of operation is primarily used for initial installation or power outage operation with battery backup.

REMOTE Position: Appliance will initiate commands from an optional wired wall switch and/or the wireless remote (RC300).

2.If using a wired wall switch with the module in REMOTE mode, the flame output can be adjusted with the HI/LO selector switch on the module. See Figure 2.3. Note that the flame HI/LO selector switch will become inactive once an optional remote control (RC200/RC300) is programmed to the control module. Note that the control module will always ignite the fireplace on HI and remain so for the initial 10 seconds of operation. If the HI/LO is switched to the LO position, the flame output will automatically drop to the lowest setting after the flame has been established for 10 sec. After this 10 second period, the flame can be adjusted from HI to LO with the switch.

3.The control module has safety feature that automatically shuts down the fireplace after 9 hours of continuous operation without receiving a command from the RC300 remote.

4.If you intend to use both an optional wired wall switch and the RC300 remote control to operate your fireplace, the wall switch will override any commands given by the remote.

5.Module Reset

This module may lock-outunder certain conditions. When this occurs, the appliance will not ignite or respond to commands. The module will go intolock-outmode by emitting three audible beeps, then continuously

displaying an error code at its status indicator LED.

Check battery tray. Remove batteries if installed. Batteries should only be installed for use during power outages. See Section H.

Locate the module selector switch. (See Figure 2.3).

Set the module selector switch to the OFF position.

Wait five (5) minutes to allow possible accumulated gas to clear.

Set the module selector switch to ON or REMOTE position.

Start the appliance.

WARNING! Risk of Explosion! DO NOT reset the module more than one time within a five minute time period. Gas may accumulate in firebox. Call a qualified service technician.

MODULE

 

 

SELECTOR

 

SWITCH

WIRE LEAD FROM

LP/NG GAS-TYPE

REGULATOR CONNECTS HERE

SELECTOR SWITCH

Figure 2.3 Control Module

Nine Hour Safety Shutdown Feature

This appliance has a safety feature that automatically shuts down the fireplace after 9 hours of continuous operation without receiving a command from the RC300 remote.

J. Before Lighting Fireplace

Before operating this fireplace for the first time, have a qualified service technician:

Verify all shipping materials have been removed from inside and/or underneath the firebox.

Review proper placement of glass panels and media.

Check the wiring.

Check the air shutter adjustment.

Ensure that there are no gas leaks.

Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

11

K. Lighting Instructions (IPI)

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

DO NOT try to light any appliance.

DO NOT touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: CAUTION:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having flammable vapors away.

DO NOT operate the appliance with fixed glass assembly removed, cracked or broken. Replacement of the fixed glass assembly should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualified installer, service agency or the gas supplier.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

Final inspection by

LIGHTING

INSTRUCTIONS (IPI)

1.This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

GAS

VALVE

2.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

3.To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4.If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFFGAS TO APPLIANCE

1.Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2.Service technician should turn off electric power to the control when performing service.

593-913G

12

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

L. After Fireplace is Lit

Initial Break-inProcedure

The fireplace should be run three to four hours continuously on high.

Turn the fireplace off and allow it to completely cool.

Remove fixed glass assembly. See Section 14.G.

Clean fixed glass assembly. See Section 3.

Replace the fixed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the fireplace.

NOTICE! Open windows for air circulation during fireplace break-in.

Some people may be sensitive to smoke and odors.

Smoke detectors may activate.

M. Frequently Asked Questions

ISSUE

SOLUTIONS

 

 

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this

condensation will disappear.

 

Blue flames

This is a result of normal operation and the flames will begin to yellow as the appliance is al-

lowed to burn for 20 to 40 minutes.

 

 

When first operated, this appliance may release an odor for the first several hours. This is caused

Odor from appliance

by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may

 

also be released from finishing materials and adhesives used around the appliance.

 

This is a normal result of the curing process of the paint and logs. Glass should be cleaned

Film on the glass

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing

 

process. A non-abrasivecleaner such as gas fireplace glass cleaner may be necessary. See

 

your dealer.

 

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

Metallic noise

the sound produced by a furnace or heating duct. This noise does not affect the operation or

 

longevity of the appliance.

Is it normal to see the pilot flame burn

In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is

turned off. Some optional control systems available with IPI models may allow pilot flame to

continually?

remain lit. In a standing pilot system the pilot will always stay on.

 

 

 

Glass rock media color change

It is normal for the glass rock media to change color slightly over the lifetime of the

appliance.

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

13

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-freeservice. We recommend annual service by a qualified service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote control instructions.

Locate remote control transmitter and receiver.

Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

Place batteries as needed in remote transmitters and battery-poweredreceivers.

Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

Remove batteries from remote controls.

Unplug 6 volt transformer plug on IPI models.

Unplug battery backup from control module.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care.

Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

DO NOT clean glass while it is hot

Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Clean glass with a non-abrasivecommercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

Assess condition of screen and replace as necessary.

Inspect for scratches, dents or other damage and repair as necessary.

Check that louvers are not blocked.

Vacuum and dust surfaces.

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

Inspect for corrosion or separation.

Verify weather stripping, sealing and flashing remains intact.

Inspect draft shield to verify it is not damaged or missing.

B.Maintenance Tasks-QualifiedService Technician

The following tasks must be performed by a qualified service technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, drop cloth and a stable work surface.

Inspect gasket seal and its condition.

Inspect fixed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

14

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Confirm there is no damage to glass or glass frame. Replace as necessary.

Verify that fixed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Interior Ceramic Glass Panel Cleaning

Frequency: Seasonally

By: Qualified Service Technician

Tools Needed: Protective gloves, glass cleaner.

CAUTION! Handle glass with care. Glass is breakable.

Avoid striking, scratching or slamming glass

Avoid abrasive cleaners

DO NOT clean glass while it is hot

Clean glass with a non-abrasivecommercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

Firebox

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, sandpaper, steel wool, cloths, mineral spirits, primer andtouch-uppaint.

Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

Replace fireplace if firebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, dust cloths

Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

Remove all foreign objects.

Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer.

Verify burner is properly secured and aligned with pilot or igniter.

Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

Verify batteries have been removed from battery back-upIPI systems to prevent premature battery failure or leaking.

Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

Inspect for lifting or other flame problems.

Verify air shutter setting is correct. See Section 14 for required air shutter setting. Verify air shutter is clear of dust and debris.

Inspect orifice for soot, dirt and corrosion. Verify orifice size is correct. See Service Parts List for proper orifice sizing.

Verify manifold and inlet pressures. Adjust regulator as required.

Inspect pilot flame pattern and strength. See Figure 3.1 for proper pilot flame pattern. Clean or replace orifice spud as necessary.

Inspect IPI flame sensing rod for soot, corrosion and deterioration. Polish with fine steel wool or replace as required.

Verify that there is not a short in flame sense circuit by checking continuity between pilot hood and flame sensing rod. Replace pilot as necessary. (IPI only)

Figure 3.1 IPI Pilot Flame Patterns

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

15

C.Glass Refractory, Base Pan, Burner and Valve Assembly Removal

It may become necessary to remove the glass panels, base pan, burner and valve assembly. This task should be performed by a qualified service technician.

1.Remove the media.

2.Remove the side glass panel retainers. See Figure 3.2. Slide the side glass panels out of the appliance as shown in Figure 3.3.

3.Remove the rear glass panel retainer, shown in Figure 3.2, and lift the rear glass panel out of the appliance.

REAR PANEL RETAINER

SIDE PANEL RETAINERS

Figure 3.2 Remove Glass Panel Retainers

4.Remove the base pan by removing the screws circled in Figure 3.4.

5.Remove the burner assembly by removing the two screws as shown in Figure 3.5. To disengage the burner from the orifice, slide the burner to the right and lift it out.

6.See Figure 3.6 for valve assembly removal.

APPEARANCE

MAY VARY

Figure 3.4 Base Pan Removal

 

 

Figure 3.5 Burner Assembly Removal

Figure 3.3 Glass Panel Removal

 

16

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Appearance of valve

components may vary.

Figure 3.6 Valve Assembly Removal

D. Burner Identification

6000CMOD-IPI(NG)

6000CMOD-IPI(LP)

Figure 3.7 Valve Assembly Removal

8000CMOD-IPI(NG)

8000CMOD-IPI(LP)

Figure 3.8 Valve Assembly Removal

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

17

4

Getting Started

Installer Guide

 

 

 

A. Typical Appliance System

NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

VERTICAL TERMINATION CAP (SECTION 10.I)

NON-COMBUSTIBLEROOF FLASHING

MAINTAINS MINIMUM CLEARANCE

AROUND PIPE (SECTION 10.G)

VENT PIPE (SECTIONS 7 and 8)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.C)

FRAMING/HEADER (SECTION 5.B)

GAS LINE (SECTION 11)

Figure 4.1 Typical System

STORM COLLAR (SECTION 10.H)

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 8.D)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.C)

OPTIONAL

WALL SWITCH (SECTION 12.C)

MANTEL AND MANTEL LEG (SECTION 5.D)

SURROUND

HEARTH EXTENSION

18

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

Where the appliance is to be installed.

The vent system configuration to be used.

Gas supply piping requirements.

Electrical wiring requirements.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

Non-corrosiveleak check solution

Hammer

Phillips screwdriver

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Flat blade screwdriver

1/2 - 3/4 in. length, #6 or #8 Self-drillingscrews One 1/4 in. female connection (for optional fan).

Caulking material (300ºF minimum continuous exposure rating)

D. Inspect Appliance and Components

Carefully remove the appliance and components from the packaging.

The vent system components and decorative doors and fronts may be shipped in separate packages.

If packaged separately, the log set and appliance grate must be installed.

Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance or vent system component.

Modification of the appliance or vent system.

Installation other than as instructed by Hearth & Home Technologies.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

19

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

NOTICE: Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

NOTE: THE REAR STANDOFF MAY NEED

TO BE REMOVED WHEN VENTING AT 45º

 

A

1/2 IN.

F

 

 

B

 

ALCOVE

A

INSTALLATION D

BC

 

 

TOP VENT

 

ONE 90º ELBOW

 

B

 

E

 

 

A

B

C

D

E

F

6000

in.

51

42

72

See Section D.

22

17-3/4

mm

1295

1067

1829

Mantel Projections

559

451

 

8000

in.

55-7/8

49

79

See Section D.

22

19-3/4

mm

1419

1245

2007

Mantel Projections

559

502

 

Figure 5.1 Appliance Locations

20

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

B. Constructing the Appliance Chase

A chase is a vertical box-likestructure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling firestops and wall shield firestops and construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with caulk with a minimum of 300ºF continuous exposure rating to seal gaps. Gas line holes and other openings should be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with unfaced insulation. If the appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth.DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specified air space clearances to appliance and vent pipe:

Insulation and other materials must be secured to prevent accidental contact.

The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with fireplace or chimney.

Failure to maintain airspace may cause overheating and a fire.

A E

 

B

 

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

H

D

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

* MINIMUM FRAMING DIMENSIONS

 

 

 

 

 

 

A

B

C**

D

E

F

G

H

I

J

Models

 

Rough

Rough

Rough

Rough

Clearance

Combustible

Combustible

Behind

Sides of

Front of

 

 

Opening

Opening

Opening

Opening

to Ceiling

Floor

Flooring

Appliance

Appliance

Appliance

 

 

(Width)

(Height)

(Depth)

(Width)

 

 

 

 

 

 

6000

in.

10

40-1/8

22

42

25

0

0

1/2

1/2

36

mm

254

1019

559

1067

635

0

0

13

13

914

 

8000

in.

10

42-1/8

22

49

25

0

0

1/2

1/2

36

mm

254

1070

559

1245

635

0

0

13

13

914

 

* Adjust framing dimensions for interior sheathing (such as sheetrock)

Figure 5.2 Clearances to Combustibles

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

21

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantels

TO CEILING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

32

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

13

12

2-1/211 10

5

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Note: All measurements in inches.

Note: Measurement is taken from top of the opening, NOT the top of the fireplace.

Figure 5.3 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

Combustible Mantel Legs or Wall Projections

INTERIOR WALL

TOP VIEW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

B

 

 

 

 

 

 

 

FIREPLACE OPENING

 

 

 

 

 

 

 

 

 

 

MANTEL LEG OR WALL PROJECTIONS

If A minimum is ____, thenB maximum is_____.

A

Inches

2-7/16

3-7/16

4-7/16

5-7/16

6-7/16

7-7/16

Millimeters

62

87

113

138

164

189

 

B

Inches

1

2

3

4

5

 

Millimeters

25

51

76

102

127

 

The CMOD door will overlap the appliance. See Figure 5.5 and 5.6.

Figure 5.5 Appliance Surround

3/8 IN.

1-3/4IN.

3/8 IN.

Figure 5.6 Door Overlaps Surround

22

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

6 Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.

Maintain vent clearance to combustibles as specified.

DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and fire.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12.................................................1.25*

Over 7/12 to 8/12.................................................1.5*

Over 8/12 to 9/12.................................................2.0*

Over 9/12 to 10/12...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12.............................................5.0

Over 14/12 to 16/12.............................................6.0

Over 16/12 to 18/12.............................................7.0

Over 18/12 to 20/12.............................................7.5

Over 20/12 to 21/12.............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge

Opening

 

 

A

B

6 in. (minimum) up to 20 in.

18 in. minimum

152 mm/508 mm

457 mm

20 in. and over

0 in. minimum

Gas, Wood or Fuel Oil

Termination Cap

B

A*

Gas

Termination

Cap **

*If using decorative cap cover(s), this distance may need to be increased. Refer to the installation instructions supplied with the decorative cap cover.

**In a staggered installation with both gas and wood or fuel oil terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Figure 6.2 Staggered Termination Caps

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

23

 

 

 

 

 

 

 

 

 

 

 

O

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

C

 

 

 

F

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

Q

 

J

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

H or i

 

 

 

 

 

 

 

V

 

B

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

D

X

V

 

E

 

 

V

 

 

 

 

G

 

 

 

 

 

 

 

V

 

H

 

 

 

 

 

 

 

 

 

V

M

 

 

V

 

 

 

 

 

 

 

 

V

V

H V

 

 

L

 

 

 

 

 

 

A

A

 

 

 

 

 

 

 

 

 

 

 

K

 

 

 

 

 

 

 

 

 

 

 

V

Electrical

K

V

 

V

 

 

 

 

 

 

 

 

= VENT TERMINAL

 

 

 

 

 

 

 

Service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X = AIR SUPPLY INLET

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

A

=

12 inches.................

clearances above grade, veranda,

 

 

 

 

porch, deck or balcony

B

=

12 inches.................

clearance to window or door that may

 

 

 

 

be opened, or to permanently closed

 

 

 

 

window

C

=

18 inches.................

clearance below unventilated soffit

 

 

18 inches.................

clearance below ventilated soffit

 

 

30 inches .................

clearance below vinyl soffits and

 

 

 

 

electrical service

D

=

9 inches...................

clearance to outside corner

E

=

6 inches...................

clearance to inside corner

F

=

3 ft. (Canada)..........

not to be installed above a gas me-

 

 

 

 

ter/regulator assembly within 3 feet

 

 

 

 

horizontally from the center-lineof the

 

 

 

 

regulator

G

=

3 ft...........................

clearance to gas service regulator

 

 

 

 

vent outlet

H

=

9 inches (U.S.A)

 

12 inches (Canada).clearance to non-mechanical(unpowered) air supply inlet, combustion air inlet ordirect-venttermination

i

= 3 ft. (U.S.A.)

 

 

6 ft. (Canada)

...........clearance to a mechanical (powered)

 

 

air supply inlet

All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below termination.

J

= 7 ft..........................

On public property: clearance above

 

 

paved sidewalk or a paved driveway.

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.

K

=

6 inches.................

clearance from sides of electrical

 

 

 

service

L

=

12 inches................

clearance above electrical service

Location of the vent termination must not interfere with access to the electrical service.

M = 18 inches...................

clearanceunderveranda,porch,deck,

 

balcony or overhang

42 inches ................

vinyl or composite overhang

Permitted when veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor.

C

V

Covered Alcove Applications

(Spaces open only on one side and with an overhang)

N= 6 inches ........... non-vinylsidewalls 12 inches ......... vinyl sidewalls

O= 18 inches ......... non-vinylsoffit and overhang 42 inches ......... vinyl soffit and overhang

P= 8 ft.

 

QMIN

RMAX

1 cap

3 feet

2 x Q ACTUAL

2 caps

6 feet

1 x Q ACTUAL

3 caps

9 feet

2/3 x Q ACTUAL

4 caps

12 feet

1/2 x Q ACTUAL

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

Measure vertical clearances from this surface.

Measure horizontal clearances from this surface.

CAUTION! Risk of Burns! Termination caps are HOT, consider proximity to doors, traffic areas or where people maypass or gather (sidewalk, deck, patio, etc.). Listed cap shields available. Contact your dealer.

Local codes or regulations may require different clearances.

Vent system termination is NOT permitted in screened porches.

Vent system termination is permitted in porch areas with two or more sides open.

Hearth & Home Technologies assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

Figure 6.3 Minimum Clearances for Termination

Vinyl protection kits are suggested for use with vinyl siding.

24

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

7 Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home Technologies DVP or SLP venting systems. Refer to Section 16B for vent component information.

DO NOT mix pipe, fittings or joining methods from different manufacturers.

The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOTvent to a pipe serving a separate solid fuel burning appliance.

B. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol

Description

 

 

V1

First section (closest to appliance) of vertical length

 

 

V2

Second section of vertical length

 

 

H1

First section (closest to appliance) of horizontal length

 

 

H2

Subsequent sections of horizontal length

 

 

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2in. (216 mm) horizontal run and8-1/2in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1).

Vertical

 

in.

 

 

 

 

.

 

 

1/2-8

 

12

in

 

 

8-1/2in.

Horizontal

Figure 7.1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

Pipe measurements are shown using the effective length of pipe (see Figure 7.2).

Horizontal terminations are measured to the outside mounting surface (flange of termination cap) (see Figure 6.3).

Vertical terminations are measured to bottom of termination cap.

Horizontal pipe installed level with no rise.

 

Pipe

Effective Length

 

Inches

Millimeters

 

 

 

DVP4

4

102

 

DVP6

6

152

Effective

DVP12

12

305

Height/Length

DVP24

24

610

 

 

DVP36

36

914

 

DVP48

48

1219

 

DVP6A

3 to 6

76 to 152

 

DVP12A

3 to 12

76 to 305

 

DVP12MI

3 to 12

76 to 305

 

DVP24MI

3 to 24

76 to 610

Figure 7.2 DVP Pipe Effective Length

 

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

25

E. Vent Diagrams

Top Vent - Horizontal Termination

Note: The 6000/8000 series fireplaces can adapt to SLP series

WARNING

vent pipe, if desired.

Fire Risk. Explosion Risk.

When venting off the top of the unit, use a DVP-2SLadapter and a

minimum 48 inch vertical section of SLP series vent pipe.

Do NOT pack insulation or other combustibles

A DVP-SLP24adapter may also be used with a 24 inch vertical

between ceiling firestops.

section of SLP series vent pipe.

• ALWAYS maintain specified clearances around

After the 48 inch vertical section, the venting table rules must be

venting and firestop systems.

• Install wall shield and ceiling firestops as speci-

followed. The first 48 inch vertical section isNOT counted as part

of the vertical components in the table. It is still counted as part of

fied.

the overall maximum run. All venting table rules for the vent run

Failure to keep insulation or other material away

must still be followed.

from vent pipe may cause fire.

Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal

WARNING

SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal

 

Fire Risk.

 

• When using DVP-HRC-SSandDVP-HRC-ZC-

 

SS termination caps on top vented fireplaces, a

 

6 inch minimum vertical vent section is required

Top Vent - Horizontal Termination

before installing first elbow.

 

One Elbow

6000CMOD-IPI

V1 Minimum

H1 Maximum

Elbow only

2 ft

610 mm

6 in.

 

152 mm

4 ft.

1.2 m

1 ft.

 

305 mm

6 ft.

1.8 m

1-1/2ft.

 

457 mm

10 ft.

3.0 m

2 ft.

 

610 m

15 ft.

4.6 m

2-1/2ft.

 

762 mm

18 ft.

5.5 m

3 ft.

 

914 mm

20 ft.

6.1 m

V1

+ H1 = 40 ft. (12.2 m) Maximum

 

H1 = 20 ft. (6.1 m) Maximum

8000CMOD-IPI

V1 Minimum

H1 Maximum

Elbow Only

2 ft.

610 mm

1 ft.

 

305 mm

3 ft.

914 mm

2 ft.

 

610 mm

6 ft.

1.8 m

3 ft.

 

914 mm

11 ft.

3.4 m

4 ft.

 

1.2 m

20 ft.

6.1 m

V1

+ H1 = 40 ft. (12.2 m) Maximum

 

H1 = 20 ft. (6.1 m) Maximum

Note: For corner installations: A 6 inch (152 mm) section of straight pipe may need to be attached to the appliance before a 90º elbow, to allow the vent pipe to clear the top standoffs.

V1

H1

Figure 7.3

26

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Two Elbows

Note: For corner installations: A 6 inch (152 mm) section of straight pipe may need to be attached to the appliance before a 90º elbow, to allow the vent pipe to clear the top standoffs.

6000CMOD-IPI

V1 Minimum

H1 + H2 Maximum

Elbow only

Not allowed

6 in.

152 mm

2 ft.

610 mm

1 ft.

305 mm

4 ft.

1.2 m

1-1/2ft.

457 mm

11 ft.

3.4 m

2 ft.

610 mm

17 ft.

5.2 m

2-1/2ft.

762 mm

20 ft.

6.1 m

V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 + H2 = 20 ft. (6.1 m) Maximum

V1 = 1 ft. (305 mm) Minimum

8000CMOD-IPI

V1 Minimum

H1 + H2 Maximum

Elbow only

Not allowed

6 in.

152 mm

Not allowed

1 ft.

305 mm

2 ft.

610 mm

2 ft.

610 mm

4 ft.

1.2 m

3 ft.

914 mm

6 ft.

1.8 m

4 ft.

1.2 m

8 ft.

2.4 m

6 ft.

1.8 m

12 ft.

3.6 m

10 ft.

3.0

20 ft.

6.1 m

V1 + H1 + H2 = 40 ft. (12.2 m) Maximum H1 + H2 = 20 ft. (6.0 m) Maximum

V1 = 1 ft. (305 mm) Minimum

H2

V1

H1

 

INSTALLED

HORIZONTALLY

Figure 7.4

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

27

Top Vent - Horizontal Termination - (continued)

Three Elbows

V1 Min.

H1 Max.

 

V2 Min.

H2 Max.

 

 

 

 

 

 

 

 

 

Elbow only

2 ft.

610 mm

0 in.

 

0 mm

1 ft.

305 mm

6 in.

152 mm

3 ft

914 mm

6 in.

 

152 mm

2 ft.

610 mm

1 ft.

305 mm

6 ft.

1.8 m

1 ft.

 

305 mm

6 ft.

1.8 m

 

 

 

 

 

 

 

 

 

2 ft.

610 mm

11 ft.*

3.4 m*

2 ft.

 

610 mm

10 ft.*

3.1 m*

 

 

 

 

 

 

 

 

 

3 ft.

914 mm

16 ft *

4.9 m*

3 ft.

 

914 mm

14 ft.*

4.3 m*

 

 

 

 

 

 

 

 

*H1 + H2 = 20 ft. (6.1 m) Maximum

V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum

 

 

 

 

 

 

 

 

 

H2

V2

H1V1

Figure 7.5

28

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Top Vent - Vertical Termination

No Elbow

V1 = 40 ft. Max. (12.4 m)

V1 = 3 ft. Min. (914 mm)

Note: If installing a vertical vent/ termination off the top of the appliance, the flue restrictor should be used. See Figure 7.9.

V1

Figure 7.6

Flue Restrictor Instructions

1. Install flue restrictor as shown below.

FLUE

RESTRICTOR

Figure 7.7

2.Break the flue restrictor into two pieces. Do this by bending the part back and forth until it breaks (see Figure 7.8).

BREAK

HERE

Figure 7.8 Flue Restrictor

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

29

Top Vent - Vertical Termination (continued)

3.Match the amount of vertical you have in the system with the chart to find the appropriate position to set the Flue Restrictor (see Figure 7.9).

Vertical

 

TOP VENT

NG

 

LP

 

 

4 ft.

1-1

 

No

 

Restrictor

 

 

 

8 ft.

2-2

 

1-2

 

 

 

 

15 ft.

3-3

 

3-2

 

 

 

 

20 ft.

3-3

 

3-3

 

 

 

 

25 ft.

3-3

 

3-3

 

 

 

 

30 ft.

3-4

 

3-4

 

 

 

 

35 ft.

3-4

 

3-4

 

 

 

 

40 ft.

3-4

 

4-4

 

 

 

 

Figure 7.9

Note: If theDVP-2SLorDVP-SLP24adapter is used with SLP pipe, you MUST subtract one number from the table above.

Example: Top vent 40 ft vertical with DVP pipe =4-4Top vent 40 ft vertical with SLP pipe =3-3

Two Elbows

V2

H1

Figure 7.11

4. Center the Flue Restrictor on vent and secure in place by using two self-tappingscrews (see Figure 7.10).

5. Reinstall the Exhaust Shield.

1 2 3 4 5

SETTING

1 2 3 4 5

Figure 7.10

 

V1

 

H1 Maximum

V2

V1 + V2 Min.

Elbow only

 

2 ft.

610 mm

*

*

 

*

6 in.

152 mm

 

6 ft.

1.8 m

*

*

 

*

2 ft.

610 mm

 

11 ft.

3.4 m

*

*

 

*

3 ft.

914 mm

 

16 ft.

4.9 m

*

*

 

*

4 ft.

1.2 m

 

20 ft.

6.1 m

*

*

 

*

 

V1 + V2 + H1

= 50 ft. (15.2 m) Maximum

 

*No specific restrictions on this value EXCEPT

 

V1 + V2 + H1 cannot exceed 50 ft (15.2 m)

V1

30

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Top Vent - Vertical Termination - (continued)

Three Elbows

 

V1

H1 + H2

V2

V1 + V2 Minimum

H1 + H2 Maximum

Elbow only

1 ft.

305 mm

*

*

*

1 ft.

305 mm

 

 

 

 

 

 

 

 

 

 

6 in.

 

152 mm

2 ft.

610 mm

*

*

*

2 ft.

610 mm

 

 

 

 

 

 

 

 

 

 

1 ft.

 

305 mm

2 ft.

610 mm

*

*

*

2 ft.

610 mm

 

 

 

 

 

 

 

 

 

 

2 ft.

 

610 mm

4 ft.

1.2 m

*

*

*

4 ft.

1.2 m

 

 

 

 

 

 

 

 

 

 

3 ft.

 

914 mm

9 ft.

2.7 m

*

*

*

9 ft.

2.7 m

 

 

 

 

 

 

 

 

 

 

4 ft.

 

1.2 m

18 ft.

5.5 m

*

*

*

18 ft.

5.5 m

H1 + H2 = 20 ft. (6.1 m) Maximum

V1 + V2 + H1 + H2 = 40 ft. (12.2 m) Maximum

 

 

 

 

 

 

 

 

 

 

V2

H1

H2

V1

 

INSTALLED

HORIZONTALLY

Figure 7.12

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

31

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent.DO NOT pack insulation or other combustibles:

Between ceiling firestops

Between wall shield firestops

Around vent system

Failure to keep insulation or other material away from vent pipe may cause over heating and fire.

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).

DVP heat shield - designed to be used on a wall 4 in. to7-1/4in. (102 mm to 184 mm) thick.

,f wall thickness is less than 4 in. the e[isting heat shields must be field trimmed. ,f wall thickness is greater than 7-1/4in. aDVP-HSM-Bwill be required.

SLP heat shield - designed to be used on a wall4-3/8in. to7-5/8in. (111 mm to 194 mm thick).

,f wall thickness is less than 4-3/8the e[isting heat shields must be field trimmed. ,f wall thickness is greater than7-5/8in. aDVP-HSM-Bwill be required.

 

(DVP-SLPPipe Shown)

 

Heat

3 in. (76 mm)

3 in. (76 mm)

Shield

top clearance *

top clearance

 

Heat

 

 

Shield

1 in. (25 mm)

 

 

clearance around

 

 

vertical sections

 

 

 

 

1 in. (25 mm)

 

Wall

clearance

 

Shield

bottom & sides

 

Firestop

 

 

 

WALL

*When using SLP or SL-Dpipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are: Top:2-1/2in. (64 mm)

Bottom: 1/2 in. (13 mm)

Sides: 1 in. (25 mm)

Figure 8.1 Horizontal Venting Clearances To Combustible

Materials

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield firestop(s). The wall shield firestop maintains minimum clearances and prevents cold air infiltration.

The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.

SLP pipe - A wall shield firestop must be placed on each side of an interior wall. A minimum 1-1/2in. (38 mm) overlap of attached heat shields must be maintained.

DVP pipe - A wall shield firestop is required on one side only on interior walls. If your local inspector requires a wall shield firestop on both sides, then both wall shield firestops must have a heat shield (refer to Section 16.B.) attached to them.

See Section 10.L for information for regarding the installation of a horizontal termination cap.

Non-CombustibleWall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable.

Whenever a non-combustiblewall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.

10 in. 12 in.

B

A*

 

 

A*

B

6000

in.

42-3/4

41-3/4

mm

1086

1060

 

8000

in.

44-3/4

44-1/8

mm

1137

1111

 

*Shows center of vent framing hole for top or rear venting. The center of the hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.

Figure 8.2 Wall Penetration

32

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

C. Install the Ceiling Firestop

A ceiling firestop MUST be used between floors and attics.

DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.3).

SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.3).

Frame the area with the same sized lumber as used in ceiling/floor joist.

The ceiling firestop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between floors that are not insulated. Refer to Figure 8.4.

Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu- lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

 

 

ATTIC ABOVE

 

 

A

 

 

A

 

PIPE

A

 

DVP

10 in. (254 mm)

 

SLP

9 in. (229 mm)

Figure 8.3

Installing Ceiling Firestop

 

 

INSTALL ATTIC INSULATION SHIELDS

 

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

 

3 FASTENERS

 

 

PER SIDE

 

 

CEILING FIRESTOP

CEILING FIRESTOP

 

INSTALLED BELOW CEILING

INSTALLED ABOVE CEILING

 

Figure 8.4 Installing the Attic Shield

 

Heat & Glo •

6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

33

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet specified clearance and be secured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Vaulted Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

Cut the attic insulation shield (if application is for vaulted ceiling) to fit your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

Wrap shield around pipe if pipe is already installed in area to be insulated.

Match the three holes in each side and fasten with three screws to form a tube.

Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling firestop.

Bend the remaining bottom tabs inward 90º to maintain the air space between the pipe and the shield. Set the shield on the ceiling firestop and attach to the firestop.

Bend all tabs inward 90º around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90°

TO MAINTAIN CLEARANCE

AND PREVENT INSULATION

FROM FALLING INSIDE

BEND 3 TABS

OUTWARD TO

FASTEN TO CEILING

FIRESTOP-BEND

REMAINING TABS

INWARD 90 DEGREES

TO MAINTAIN

INSERT 3 CLEARANCE

SCREWS

Figure 8.5 Attic Insulation Shield

E. Installing the Optional Heat-Zone® Gas Kit

Remove the knockout from the fireplace and discard it (see Figure 8.6).

Center the duct collar around the exposed hole and attach it to the fireplace with 3 screws. Note: Do this BEFORE final positioning of fireplace.

Determine the location for the air register/fan housing assembly.

Reference the Heat-Zone® Gas kit instructions for the remaining installation steps.

HEAT-ZONE®GAS

ATTACHES HERE

Figure 8.6 Heat Zone Cover Plate

34

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

9 Appliance Preparation

A. Top Vent

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Figure 9.1 Cut the seal cap strap across the rectangles next to the disk. For rear vent, skip this step.

Figure 9.2 Remove the white gasket material covering the seal cap.

Figure 9.3 Remove the seal cap.

Figure 9.4 Remove the insulation basket and white insulation from the center vent pipe.

Figure 9.5 Remove the insulation from the outer vent pipe. For rear venting there is no insulation in the outer vent pipe.

Figure 9.6 To attach the first section of vent pipe, make sure to use the fiberglass gasket in the manual bag to seal between the first vent component and the outer fireplace wrap. Use 2 self tapping screws to secure the gasket to the outer wrap.

Secure the first section of venting to the fireplace by screwing through the two straps left over from cutting the seal cap strap in step 2.

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

35

B. Installing the Non-combustibleBoard

The factory supplied non-combustibleboard spans the distance from the top of the fireplace to the center of the framing header. This board must be used. See Figure 9.7.

WARNING! Risk of Fire! Non-combustibleboard must be installed across the top of the fireplace per Figure 9.7.

HEADER

Figure 9.7 Non-combustibleBoard

A

B

Note: Diagonal dimensions (A) and (B) must be within 1/4 inch of each other.

Figure 9.8 Positioning the Appliance Squarely

C. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

Sagging or loose insulation

Insulation backing or plastic

Framing and other combustible materials

Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs.

Failure to maintain air space clearance may cause overheating and fire.

The diagram shows how to properly position and secure the appliance (see Figure 9.9). Nailing tabs are provided to secure the appliance to the framing members.

Bend out nailing tabs on each side.

Place the appliance into position.

Keep nailing tabs flush with the framing.

Level the appliance from side to side and front to back.

“Square” the unit by securing diagonal dimensions to within 1/4 inch of each other. See Figure 9.8.

Shim the appliance as necessary. It is acceptable to use wood shims underneath the appliance.

Secure the appliance to the framing by using nails or screws through the nailing tabs.

Secure the appliance to the floor by inserting two screws through the pilot holes at the bottom of the appliance.

NAILING TABS

(BOTH SIDES)

PILOT HOLES

Figure 9.9 Proper Positioning and Securing of an Appliance

36

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

10 Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only)

Attach Vent to the Firebox Assembly

Note: The end of the pipe sections with the lanced tabs will face toward the appliance.

Attach the first pipe section to the starting collar:

Lanced pipe end to the starting collar

Inner pipe over inner collar

Push the pipe section until all lanced tabs snap in place

Lightly tug on pipe to confirm it has locked.

Commercial, Multi-family(Multi-levelexceeding two stories), orHigh-RiseApplications

All outer pipe joints must be sealed with high temperature silicone (minimum of 300ºF continuous exposure rating), including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 10.1

Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Assemble Pipe Sections

Per Figure 10.2:

Start the inner pipe on the lanced end of section A into the flared end of section B.

Start the outer pipe of section A over the outer pipe of section B.

Once both vents sections are started, push firmly until all lanced tabs lock into place.

Lightly tug on the pipe to confirm the tabs have locked.

It is acceptable to use screws no longer than 1/2 in. (13 mm) to hold outer pipe sections together. If predrilling holes, DO NOT penetrate inner pipe.

For 90º and 45º elbows that are changing the vent direction from horizontal to vertical, one screw minimum should be put in the outer flue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1/2 in. (13 mm). If predrilling screw holes, DO NOT penetrate inner pipe.

Figure 10.1 High Temperature Silicone Sealant

A

Lances

B

Figure 10.2

Figure 10.3

Note: Make sure that the seams are not aligned to prevent unintentional disconnection.

CORRECT

Figure 10.4 Seams

INCORRECT

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

37

B. Assemble Vent Sections (SLP Pipe Only)

To attach the first vent component to the starting collars of the appliance:

Attach a DVP-2SLorDVP-SLP24adapter to the starting collar of the appliance.

Lock the vent components into place by sliding the pipe section onto the collar.

Align the seam of the pipe and seam of collar to allow engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 10.5.

Slide the gasket over the first vent section and place it flush to the appliance. This will prevent cold air infiltration. Caulk with a minimum of 300ºF continuous exposure rating may be used to hold the part in place.

Continue adding vent components, locking each succeeding component into place.

Ensure that each succeeding vent component is securely fitted and locked into the preceding component.

Commercial, Multi-family(Multi-levelexceeding two stories), orHigh-RiseApplications

For Installation into a commercial, multi-family(multi-levelexceeding two stories) orhigh-riseapplications: All outer pipe joints must be sealed with high temperature silicone (minimum of 300ºF continuous exposure rating), including the slip section that connects directly to the horizontal termination cap.

Apply a bead of silicone sealant (minimum of 300ºF continuous exposure rating), inside the female outer pipe joint prior to joining sections. See Figure 10.1.

Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated.

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 10.5 Adding Venting Components

C. Assemble Slip Sections

Slide the inner flue of the slip section into the inner flue of the pipe section and the outer flue of the slip section over the outer flue of the pipe section. See Figure 10.6.

Slide together to the desired length.

Pilot hole

Figure 10.6 Slip Section Pilot Holes

Maintain a 1-1/2in. (38 mm) overlap between the slip section and the pipe section.

Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 10.7.

Figure 10.7 Screws into Slip Section

Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length.

NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a high temperature silicone sealant(minimum of 300ºF continuous exposure rating),.

Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

Only outer pipes are sealed, sealing the inner flue is not required.

All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed.

38

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

D. Secure the Vent Sections

Vertical runs of DVP pipe must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise.

Vertical runs of SLP pipe must be supported every 8 ft. (2.44 m).

Horizontal sections must be supported every 5 feet (1.52 m).

Vent supports or plumbers strap (spaced 120º apart) may be used to support vent sections. See Figures 10.8 and 10.9.

Wall shield firestops may be used to provide horizontal support vent sections.

SLP ceiling firestops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

120º

Figure 10.8 Securing Vertical Pipe Sections

120º

Figure 10.9 Securing Horizontal Pipe Sections

E. Disassemble Vent Sections

Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.11.

Pull carefully to separate the pieces of pipe.

Figure 10.10 Rotate Seams for Disassembly

Figure 10.11 Align and Disassemble Vent Sections

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

39

F.Install Decorative Ceiling Components (SLP only)

A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling thimble is used to cover the firestop.

Seal the gap between the vent pipe and firestop using high temperature silicone (minimum of 300ºF continuous exposure rating) to prevent cold air infiltration.

Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.

A decorative cathedral ceiling support box can be installed on a cathedral ceiling through which the vent passes.

Use a plumb-bobto mark the center line of the venting system on the ceiling and drill a small hole through the ceiling and roof at this point. Locate the hole and mark the outline of the cathedral ceiling support box on the outside roof.

Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure 10.12).

Level the support box both vertically and horizontally and temporarily tack it in place through the inside walls into the roof sheathing.

Use tin snips to cut the support box from the top corners down to the roof line and fold the resulting flaps to the roof. See Figure 10.13.

Nail the flaps to the roof AFTER running a bead of non hardening sealant between the flaps and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

LEVEL

CATHEDRAL CEILING

SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm)

GREATER IN SIZE THAN

PATTERN OF SUPPORT

BOX AS IT IS PROJECTED

ONTO ROOF LINE

Figure 10.12

Figure 10.13

40

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

G. Install Metal Roof Flashing

See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof.

Slide the roof flashing over the pipe sections extending through the roof as shown in Figure 10.15.

 

 

HORIZONTAL

 

 

OVERHANG

2 FT.

20 INCHES MIN.

VERTICAL

MIN.

 

 

WALL

 

LOWEST

 

 

 

DISCHARGE

 

 

OPENING

 

GAS DIRECT VENT

 

 

TERMINATION CAP

 

 

 

 

X

 

 

12

 

 

ROOF PITCH

 

 

IS X/ 12

 

H (MIN.) - MINIMUM HEIGHT FROM ROOF

 

TO LOWEST DISCHARGE OPENING

Roof Pitch

 

H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12............................1.25*

Over 7/12 to 8/12..............................1.5*

Over 8/12 to 9/12..............................2.0*

Over 9/12 to 10/12............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12........................... 5.0

Over 14/12 to 16/12........................... 6.0

Over 16/12 to 18/12........................... 7.0

Over 18/12 to 20/12........................... 7.5

Over 20/12 to 21/12........................... 8.0

* 3 foot minimum in snow regions

Figure 10.14 Minimum Height From Roof To Lowest Discharge

Opening

 

 

NOTICE: Failure to properly caulk the roof flashing and pipe seams may permit entry of water.

Caulk the gap between the roof flashing and the outside diameter of the pipe.

Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 10.15.

Caulk the overlap seam of any exposed pipe sections that are located above the roof line.

CAULK

Figure 10.15

H. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

Connect both halves of the storm collar with two screws (see Figure 10.16).

Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 10.17).

Caulk around the top of the storm collar (see Figure 10.23).

Figure 10.16 Assembling the Storm Collar

Figure 10.17 Assembling the Storm Collar Around the Pipe

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

41

I. Install Vertical Termination Cap

Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

Secure the cap by driving three self-tappingscrews (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 10.23).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 10.23

J.Install Decorative Wall Components (SLP only)

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the wall shield firestop.

Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 10.24.

Figure 10.24 Wall Thimble

K.Heat Shield Requirements for Horizontal Termination

WARNING! Risk of Fire! To prevent overheating and fire, heat shields must extend through the entire wall thickness.

DO NOT remove the heat shields attached to the wall shield firestop and the horizontal termination cap (shown in Figure 10.25).

Heat shields must overlap 1-1/2in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attachedto the wall shield firestop. The other section isfactory-attachedto the cap. See Figure 10.25.

If the wall thickness does not allow the required 1-1/2in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

If the wall thickness is less than 4 in./102 mm (DVP) or 4-3/8in./ 111 mm (SLP), the heat shields on the cap and wall shield firestop must be trimmed. A minimum1-1/2in. (38 mm) overlap MUST be maintained.

Use an extended heat shield if the finished wall thickness is greater than 7-1/4in. (184 mm).

The extended heat shield may need to be cut to length maintaining sufficient length for a 1-1/2in. (38 mm) overlap between heat shields.

Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields maynot be field constructed.

42

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

L.Install Horizontal Termination Cap (DVP and SLP Pipe)

WARNING! Risk of Fire! The telescoping flue section of the termination cap MUST be used when connecting vent.

1-1/2(38 mm) minimum overlap of flue telescoping section is required.

Failure to maintain overlap may cause overheating and fire.

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at outside edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current

ANSI Z223.1 and CAN/CGA-B149installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

NOTICE: For certain exposures which require superior resistance towind-drivenrain penetration, a flashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps withfactory-suppliedheat shield attached, no additional wall shield firestop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

HEAT SHIELD

EXTENDED

1-1/2IN. (38 MM) MIN.

HEAT SHIELD

OVERLAP

WALL SHIELD

 

FIRESTOP

 

SLIP SECTION

 

CAN BE EXTENDED

 

INNER VENT

SHEATHING

OUTER VENT

 

INTERIOR

EXTERIOR

VENT DEPTH FROM BACK OF APPLIANCE TO

 

OUTSIDE SURFACE OF EXTERIOR WALL

 

(SEE CHART BELOW)

 

Figure 10.25 Venting through the wall

Cap Specification Chart

(depth without using additional pipe sections)

 

DVP-TRAPK1

DVP-TRAPK2

6000

Top Vent Depth

Top Vent Depth

2-3/4in. to4-5/8in.

5-1/8in. to9-1/8in.

Series

 

 

 

 

8000

 

 

Series

DVP-HPC1

DVP-HPC2

 

Top Vent Depth

Top Vent Depth

 

2-3/4in. to4-7/8in.

4-7/8in. to 9 in.

DVP-TRAP1can adjust1-1/2in.(3-1/8to4-5/8in.)

DVP-TRAP2can adjust 4 in.(5-3/8to9-3/8)

DVP-HPC1can adjust2-1/8in.(4-1/4to6-3/8)

DVP-HPC2can adjust4-1/8in.(6-3/8to10-1/2)

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

43

11 Gas Information

A. Fuel Conversion

Make sure the appliance is compatible with available gas types.

Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

B. Gas Pressure

Optimum appliance performance requires proper input pressures.

Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

Pressure requirements are:

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

10.0 in. w.c.

13.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

WARNING! Risk of Fire or Explosion! High pressure will damage valve. Low pressure may cause explosion.

Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm)T-handlemanualshut-offvalve and flexible gas connector are connected to the 1/2 in. (13 mm) control valve inlet.

If substituting for these components, please consult local codes for compliance.

C. Gas Connection

Refer to Reference Section 16 for location of gas line access in appliance.

Gas line may be run through knockout(s) provided.

The gap between supply piping and gas access hole may be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air infiltration.

Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

Pipe incoming gas line into valve compartment.

Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.

Purge should be performed by qualified service technician.

Ensure adequate ventilation.

Ensure there are no ignition sources such as sparks or open flames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all fittings and connections with a non-corrosivecommercially availableleak-checksolution.DO NOT use open flame. Fittings and connections could have loosened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

In the USA: Reduce burner orifice 4% for each 1000 feet above 2000 feet.

In CANADA: Reduce burner orifice 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

44

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

12 Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, withNational Electric Code ANSI/NFPA 70-latest edition or theCanadian Electric

Code CSA C22.1.

Wire the appliance junction box to 110-120VAC. This is required for use of optional accessories (standing pilot ignition) or proper operation of the appliance (IntelliFire PlusTM ignition).

A 110-120VAC circuit for this product must be protected withground-faultcircuit-interrupterprotection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 110V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

B. IntelliFire PlusTM Ignition System Wiring

Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

Refer to Figure 12.1, IPI Wiring Diagram.

This appliance is equipped with an IntelliFire PlusTM control valve which operates on a 6 volt system.

Plug the 6 volt transformer plug into the appliance junction box to supply power to the unit OR install 4 AA cell batteries (not included) into the battery pack before use.

C. Optional Accessories Requirements

This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

Hearth & Home Technologies recommends that IntelliFire PlusTM wireless controls be used for their features and functionality with the IntelliFire PlusTM ignition system.

• A standard ON/OFF switch is compatible.

 

 

FLAME

IGNITER

 

 

 

 

SENSE

 

 

 

 

 

 

 

TO JUNCTION

 

 

 

 

 

BOX (110V)

 

 

 

 

 

 

MODULE

 

 

 

 

FLAME

 

 

 

 

 

MODULATION

 

 

 

 

 

 

 

RC100

RC200

RC300

 

 

 

(OPTIONAL WALL CONTROLS)

ORANGE

GREEN

 

BATTERY PACK

 

 

(PILOT)

(MAIN)

 

 

 

 

6V DC

 

 

 

 

BLACK

 

 

 

 

 

 

 

 

 

RED

 

THERMOSTAT WIRE

 

 

 

 

 

 

 

 

 

 

ASSEMBLY / WALL

 

 

BROWN

 

SWITCH WIRE

 

 

 

GROUND

 

 

 

Figure 12.1 IPI Wiring Diagram

 

 

 

 

 

Heat & Glo •

6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

45

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105º C rated wire. Wire must have high temperature insulation.

E. Junction Box Installation

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 12.2).

Pull the electrical wires from outside the appliance through the opening into the valve compartment and secure wires with a Romex connector. See Figure 12.2.

Make all necessary wire connections to the junction box/ receptacle and reattach the junction box/receptacle to the outer shell.

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.3):

The power supply for the appliance must be brought into a switch box.

The power can then be supplied from the switch box to the appliance using a minimum of 14-3with ground wire.

At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

Add a 1/4 in. insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 in. male) as shown.

 

Romex

 

Connector

 

14/2WG

 

Cover Plate

 

outside firebox

WHT

 

BLK

 

WHT

 

BLK

Copper

 

GRN wire

ground attached

to GRN screw with

inside box

 

GRN wire

NOTICE: DO NOT wire

110 VAC to wall switch.

Figure 12.2 Junction Box Detail

 

Minimum 14-3AWG

 

Switch

 

 

with Ground

 

 

 

Red

 

 

Black

Black

 

White

White

Junction Box

Green

Green

Red Black White Green

 

Power

 

Switch Box

 

Supply

 

 

 

 

Wires

 

Knockout

 

Red

 

 

Figure 12.3 Junction Box Wired to Wall Switch or BC10

46

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

13 Finishing

A. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.)

The CMOD door will overlap the appliance. See Figure 13.3 and 13.4.

Combustible Mantels

Note: All

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO CEILING

measurements

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in inches.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

32

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

13

12

2-1/211 10

5

MEASUREMENTS FROM TOP EDGE OF THE OPENING

Note: Measurement is taken from top of the opening, NOT the top of the fireplace.

Figure 13.1 Minimum Vertical and Maximum Horizontal

Dimensions of Combustibles

Combustible Mantel Legs or Wall Projections

INTERIOR WALL

TOP VIEW

A B

FIREPLACE OPENING

MANTEL LEG OR WALL PROJECTIONS

If A minimum is ____, thenB maximum is_____.

A

Inches

2-7/16

3-7/16

4-7/16

5-7/16

6-7/16

7-7/16

Millimeters

62

87

113

138

164

189

 

B

Inches

1

2

3

4

5

 

Millimeters

25

51

76

102

127

 

Figure 13.2 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Figure 13.3 Appliance Surround

3/8 IN.

1-3/4IN.

3/8 IN.

Figure 13.4 Door Overlaps Surround

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

47

B. Facing Material

Metal front faces may be covered with non-combustiblematerials only.

Facing and/or finishing materials must not interfere with air flow through louvers, operation of louvers or doors, or access for service.

Facing and/or finishing materials must never overhang into the glass opening.

Observe all clearances when applying combustible materials.

Seal joints between the finished wall and appliance top and sides using a 300ºF minimum sealant. Refer to Figure 13.3.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as specified in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

B

FACTORY-INSTALLEDNON-COMBUSTIBLEBOARD

DO NOT REMOVE

A

 

 

A

B

 

 

 

 

6000

inches

39-3/4

41

millimeters

1010

1041

 

8000

inches

41-3/4

48

millimeters

1060

1219

 

Figure 13.5 Noncombustible Facing Diagram

C. Finish and Sealing Joints

All joints between the finished wall sheathing and the appliance must be sealed with non-combustiblematerials. Sealants, such as caulk or mastic used to seal the gap between the wall and the fireplace, should be rated at a minimum continuous exposure to 300ºF.

Finishing Around Opening with Gypsum Wallboard

Gypsum wallboard (drywall) joints adjacent to the fireplace opening, including the non-combustibleboard on the appliance, require special attention to minimize cracking. When installing gypsum wallboard around the fireplace, install the hole for the fireplace opening in a single wallboard sheet, if possible. This will minimize the joints adjacent to the fireplace opening.

Tape wall board joints around the fireplace opening with fiberglass-meshtape. It will provide a morecrack-resis-tant joint than paper tape. Fill, smooth and finish wall joints with chemicallysetting-typejoint compound. It will provide a morecrack-resistantjoint thanair-dryinglightweight compound.

Painting

If desired finishing includes a painted wall, 100% acrylic latex with compatible primer is recommended around this appliance. Oil-basedor standard acrylic paints may discolor due to heat exposure.

48

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

D. Door Selection

Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. The CMOD door can not be used if the appliance is installed directly on the floor. See Figure 13.6 and 13.7.

Folio Door Application

If the appliance is installed on the floor or level with an elevated hearth, the Folio Door MUST be used. The CMOD door is not compatible with this type of installation as a minimum elevation of 1 inch is required on the bottom of the appliance.

WALL

WALL

 

FOLIO DOOR

FLOOR/

 

ELEVATED

 

HEARTH

 

 

FLOOR/

 

ELEVATED

 

HEARTH

Figure 13.6 Appliance Installed on Floor or Elevated Hearth

CMOD Door Application

If the appliance is installed at a minimum of 1 inch above the floor, the CMOD door can be used. The CMOD door OVERLAPS the sides, top and bottom of the appliance surround. See Figure 13.3 and 13.4 for dimensions.

WALL

FLOOR/ELEVATED HEARTH

NOTE: THE APPLIANCE MUST BE ELEVATED A MINIMUM OF 1 INCH IN ORDER TO USE THE CMOD DOOR.

CMOD DOOR

WALL

FLOOR/ELEVATED HEARTH

Figure 13.7 Appliance Installed Off the Floor

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

49

Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. Once you have determined what kind of door and finishing material is going to be used on the fireplace, you may use the table below which shows the door models and the finishing material thickness allowed.

DOOR

FIT

FINISH MATERIAL

SEE

THICKNESS

FIGURE

 

 

CMOD-8-BK

Overlap

1 inch thick or less

13.8

CMOD-8-GY

Inside

1-4inches maximum

13.9

CMOD-6-BK

Overlap

1 inch thick or less

13.8

CMOD-6-GY

Inside

1-4inches maximum

13.9

FOLIO

Inside

Any

13.10

Finishing Material:

1 Inch Thick or Less - Overlap Fit Method

1 in. MAX. DOOR FINISHING MATERIAL

(TOP EDGE)

Finishing materials 1 inch maximum thick.

Stop finishing material flush with opening.

NON-COMBUSTIBLE

FINISHING MATERIAL

Figure 13.8 Finishing Material 1 Inch Thick or Less

50

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Finishing Material Thickness:

Greater than 1 Inch - Inside Fit Method

NOTICE: Non-combustiblefinishing materials greater than one inch require the inside fit method.

NON-COMBUSTIBLE

FINISHING MATERIAL

FINISHING

FINISHING

MATERIAL

MATERIAL

DOOR

A

(Outside door width)

C

(Includes 1/8 in. opening each side of door)

B

D

A

(Outside door width)

C

(Includes 1/8 in. opening each side of door)

E

Finishing Material Thickness Greater than 1 Inch B = Top of door to bottom of fireplace.

D = Bottom of Finishing Material to Bottom of Fireplace

 

8000 Models

6000 Models

 

Inches

Millimeters

Inches

Millimeters

A

48-13/16

1240

41-13/16

1062

B

38-3/8

975

36-3/8

924

C

49-1/16

1246

42-1/16

1068

D

39-1/4

997

37-1/4

946

E

3/8

10

3/8

10

Finishing Material:

0 - 4 Inches - Inside Fit Method

NON-COMBUSTIBLE

FINISHING MATERIAL

DOOR

FINISHING MATERIAL

FINISHING MATERIAL

Figure 13.10 Folio Inside Fit

Figure 13.9 Finishing Material Thickness Greater Than One Inch

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

51

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14.G.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Glass Panel Installation

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation.

CAUTION! Glass is fragile. Handle with care.

1.Install the rear glass panel as shown in Figure 14.1. the panel retainers and screws are included in the appliance manual bag.

Note: Screw the three glass panel retainers to the firebox using the EXISTING pilot holes.

2.Slide the side glass panels in positions as shown in Figure 14.2.

3.Figure 14.3. shows the glass panels installed properly.

REAR RETAINER

Figure 14.1 Install Rear Retainer

Figure 14.2 Install Side Glass Panels

SIDE RETAINERS

Figure 14.3 Install Side Retainers

52

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

F. Media Placement

WARNING! Risk of Explosion! Follow media placement instructions. Improperly placed media interfere with proper burner operation.Fireplace will not function properly. Delayed ignition may occur.

WARNING! Choking Hazard! Keep media out of reach of children.

DO NOT place media in pilot opening.

DO NOT place media in a position that it may fall into the pilot opening.

DO NOT use any media other than the media supplied with this fireplace or listed in Service Parts Section in this manual.

DO NOT use more than 14 lb. of media per 8000CMODIPI or 12 lb. per 6000CMOD-IPIfireplace. Note: One bag of glass contains 7 lbs.

6000CMOD-IPI:Extra 2 lbs. may be saved for future use.

1.Place media evenly on the base pan. Figure 14.9 shows properly placed media.

2.The media can only be placed in the shaded areas as shown in Figure 14.7 and Figure 14.8.

3.Do not apply media over the pilot opening. See Figure 14.7 and Figure 14.8.

4.The rock fixture assembly is factory installed in the appliance. See Figure 14.4 and Figure 14.5.

5.After the media is properly installed, carefully remove the rock fixture assembly. Do not allow any media to fall into the opening. See Figure 14.6. Store the rock fixture assembly under the appliance for future use.

Figure 14.4 Rock Fixture Installed

Figure 14.5 Rock Fixture Assembly Installed

THIS JIG MUST BE USED FOR STONE PLACEMENT

REMOVE BEFORE BURNING

DO NOT DISCARD

REMOVE SCREW

Figure 14.6 Remove Rock Fixture Assembly

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

53

BURNER

NO MEDIA ON

PILOT OPENING

(WHITE AREA)

Figure 14.7 Placement of Media

BURNER

NO MEDIA ON

PILOT OPENING

(WHITE AREA)

Figure 14.8 Placement of Media

Figure 14.9 Proper Placement of Media

54

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

G. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace as a complete assembly.

Removing Fixed Glass Assembly

Pull the four glass assembly latches out of the groove on the glass frame. Remove glass door from the appliance (see Figure 14.7).

Replacing Fixed Glass Assembly

Replace the glass door on the appliance. Pull out and latch the four glass assembly latches into the groove on the glass frame.

LATCHES

(BOTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

Figure 14.7 Fixed Glass Assembly

H. Install Trim and/or Surround

Install optional trim kits and/or surrounds using the instructions included with the accessory.

Use non-combustiblematerials to cover the gap between the sheet rock and the appliance (when applicable to the model).

I. Air Shutter Setting

Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.8.

Loosen the wing nut.

Move the air handle to the left to open the air shutter.

Move the air handle to the right to close the air shutter.

Tighten the wing nut.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

Appearance of

components may vary.

AIR SHUTTER

WING NUT

Figure 14.8 Air Shutter

Air Shutter Settings

 

NG

LP

6000

Fully Closed

Fully Open

8000

Fully Open

Fully Open

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

55

15 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician.

A. IntelliFire PlusTM Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

A. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

The ignitor/module

 

connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

B. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

spark.

 

shorts in the wiring.

ule to pilot assembly. Verify connections underneath pilot assembly

 

 

are tight; also verify igniter and flame sense wires are not grounding

 

 

out to metal chassis, pilot burner, pilot enclosure, mesh screen if

 

 

present, or any other metal object.

 

 

 

 

C. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

2. Pilot won’t light,

A. No power, transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly or depleted batteries.

voltage of transformer at connection to module. Acceptable read-

spark.

 

ings of a good transformer are between 6.4 and 6.6 volts AC. Bat-

 

 

tery power supply voltage must be at least 4 volts. If below 4 volts,

 

 

replace batteries.

 

 

 

 

B. A shorted or loose connection in

Remove and reinstall the wiring harness that plugs into module.

 

wiring configuration or wiring har-

Verify there is a tight fit. Verify pilot assembly wiring to module. Re-

 

ness.

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

C. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

 

 

 

 

D. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

3. Pilot sparks, but

A. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits.

 

 

 

 

B. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

D. Pilot valve solenoid.

Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.

 

 

If below 1.5 volts, replace module. If 1.5 volts or greater, replace

 

 

valve.

 

 

 

56

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

Troubleshooting (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

A. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify

ues to spark, and main

 

flame sense or igniter wires are not grounding out to metal

burner will not ignite.

 

chassis, pilot burner, pilot enclosure or screen if present, or

(If the pilot continues

 

any other metal object.

to spark after the

 

 

B. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. With a multi-

not occurred.)

 

 

meter, verify that current in series between module and

 

 

 

 

sense lead is at least 0.14 microamps. Verify correct pilot

 

 

orifice is installed and gas inlet is set to pressure specifi-

 

 

cations. Polish flame sensing rod with fine steel wool to

 

 

remove any contaminants that may have accumulated on

 

 

flame sensing rod.

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of ap-

 

 

pliance. Verify that wire harness is firmly connected to the

 

 

module.

 

 

 

 

D. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing rod

 

nated flame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

flame sensing rod to white sensor wire. Polish flame sens-

 

 

ing rod with fine steel wool to remove any contaminants

 

 

that may have accumulated on flame sensing rod. Verify

 

 

continuity with a multi-meterwith ohms set at lowest range.

 

 

Replace pilot if any damage is detected.

 

 

 

 

E. Module.

Turn ON/OFF rocker switch or wall switch to OFF position.

 

 

Remove ignitor wire “I” from module. Place ON/OFF rocker

 

 

switch or wall switch in ON position. If there is no spark at “I”

 

 

terminal module must be replaced. If there is a spark at “I”

 

 

terminal, module is fine.

 

 

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

57

16 Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

L

J

K

N

TOP VIEW

 

GAS LINE

H

 

ACCESS

 

 

R

I

 

C

D

 

 

G

 

O

E

 

Q

P

B

F

A

 

 

LEFT SIDE

FRONT VIEW

RIGHT SIDE

Location

Inches

Millimeters

A

41

1041

B

36-1/8

918

C

33-1/2

851

D

34-5/8

879

E

2-1/4

57

F

9-11/16

246

G

26-7/8

683

H

6 dia

152

I

39-7/8

1013

Location

Inches

Millimeters

J

21

533

K

11-11/16

297

L

28-1/2

724

M

14-1/4

362

N

8-1/2

216

O

2-7/8

73

P

8-1/2

216

Q

1

25

R

40-7/8

1038

Figure 16.1 Appliance Dimensions-6000Models

58

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

L

M

J

N

K

 

TOP VIEW

H

GAS LINE

ACCESS R

I

 

 

 

C

D

 

 

 

 

 

 

 

 

G

 

O

Q

 

E

 

 

 

 

 

 

 

P

 

B

 

F

 

 

A

 

 

 

 

 

LEFT SIDE

 

FRONT VIEW

 

RIGHT VIEW

Location

Inches

Millimeters

A

48

1219

B

43-1/8

1096

C

35-1/2

902

D

36-5/8

930

E

2-3/8

60

F

9-15/16

252

G

28-7/8

734

H

6

152

I

41-7/8

1064

Location

Inches

Millimeters

J

21

533

K

11-11/16

297

L

35-1/2

901

M

17-3/4

451

N

8-1/2

216

O

2-7/8

73

P

8-1/2

216

Q

1

25

R

42-7/8

1089

Figure 16.2 Appliance Dimensions-8000Models

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

59

B. Vent Components Diagrams

 

 

 

Pipe

Effective Length

 

 

 

 

 

Inches

Millimeters

10-1/2in.

 

 

 

 

 

 

 

Effective

 

DVP4

4

102

(267 mm)

45°

 

Height/Length

 

DVP6

6

152

 

 

 

 

 

 

 

 

 

 

DVP12

12

305

4-7/8in.

 

 

 

 

DVP24

24

610

 

 

 

(124 mm)

 

 

 

DVP36

36

914

 

10-7/8in.

 

DVP Pipe (see chart)

 

DVP48

48

1219

 

(276 mm)

 

 

DVP6A

3 to 6

76 to 152

DVP45 (45º Elbow)

 

 

 

 

 

 

DVP12A

3 to 12

76 to 305

 

 

 

 

 

DVP12MI

3 to 12

76 to 305

 

 

 

 

 

DVP24MI

3 to 24

76 to 610

 

 

 

 

 

 

 

 

 

11-3/8in.

 

 

 

 

 

 

 

(289 mm)

 

 

 

10 in.

1 in.

 

 

 

 

 

(254 mm)

 

 

 

 

 

(25 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7-3/8in.

 

 

 

 

 

 

 

(187 mm)

 

10 in.

 

 

 

 

 

1-1/4in. (32 mm)

 

(254 mm)

 

 

 

9-1/4in.

 

 

 

 

 

 

 

 

 

Assembled

 

 

 

 

(235 mm)

1/2 in. TYP

 

Height: 24 in./610 mm

 

 

 

 

13-1/4in.

(13 mm)

 

Diameter: 10 in./254 mm

 

 

 

 

 

 

 

 

 

 

(337 mm)

 

 

DVP-AS2

 

DVP-FS(Ceiling Firestop)

DVP90ST (90° Elbow)

 

 

 

 

 

 

12 in.

1 in.

 

 

 

 

 

 

(305 mm)

(25 mm)

 

10 in.

 

1- 1/2 in.

 

 

 

8 in.

 

 

 

 

 

(203 mm)

 

(254 mm)

 

(38 mm)

 

14 in.

 

 

 

 

 

 

 

 

 

 

UP

 

 

 

(356 mm)

 

 

 

 

 

 

 

 

 

5 in.

 

12 in.

 

 

 

 

 

(127 mm)

(305 mm)

 

 

 

 

 

 

 

 

 

 

6 in.

 

 

 

 

 

 

 

(152 mm)

 

 

DVP-HVS(Vent Support)

 

 

 

 

DVP-WS(Wall Shield Firestop)

 

Figure 16.2 DVP vent components

 

 

 

 

 

 

60

Heat & Glo •

6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

 

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm).The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than7-1/4in. (184 mm) aDVP-HSM-Bwill be required.

8 in.

(203 mm) Heat Shield

15-1/8in.

(384 mm)

 

 

Term Cap

Minimum

Maximum

 

 

Effective Length

Effective Length

 

Max

 

12 in.

Trap1

3-1/8in.

4-5/8in.

(305 mm)

Effective

79 mm

117 mm

DVP-TRAP

Length

 

 

Trap2

5-3/8in.

9-3/8in.

Horizontal Termination Cap

 

137 mm

238 mm

 

 

 

 

DVP-TRAP1

DVP-TRAP2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP-TRAPK1

 

 

 

 

 

 

 

DVP-TRAPK2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVP-HPC1

DVP-HPC2

Figure 16.3 DVP vent components

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

61

B. Vent Components Diagrams (continued)

 

 

 

 

 

31 in.

 

 

 

 

 

 

 

(787 mm)

 

 

13-1/4in.

 

 

 

 

 

 

(337 mm)

 

 

24-5/8in.

 

 

 

 

 

 

(625 mm)

 

 

 

 

24-5/8in.

27-1/2in.

 

 

 

 

 

 

(625 mm)

(699 mm)

 

 

 

13-1/4in.

 

 

 

 

 

 

 

 

 

 

 

 

(337 mm)

 

RF6M

 

 

 

RF12M

 

 

 

Roof Flashing Multi-pak

 

 

 

 

 

 

Roof Flashing Multi-pak

 

 

 

 

 

 

 

 

 

13-3/4in.

5 in.

 

 

11-7/8in.

 

5 in.

 

(349 mm)

(127 mm)

 

 

(302 mm)

(127 mm)

 

13-3/4in.

 

 

13-7/8in.

 

 

 

 

 

 

(352 mm)

 

 

 

 

(349 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

BEK

 

 

 

DVP-BEK2

 

 

 

Trap Cap Brick Extension

 

 

DVP-HPCCap Brick Extension

 

 

 

 

11-5/8in.

 

 

 

 

 

 

 

(295 mm)

 

 

 

 

 

 

7-1/8in.

 

12-1/8in.

 

 

 

 

 

(308 mm)

 

 

 

 

(181 mm)

 

 

 

 

 

 

 

 

 

 

 

DVP-TRAPFL

 

5-3/4in.

 

 

 

 

 

 

(146 mm)

COOL-ADD

 

 

 

Flashing

 

 

 

 

 

 

 

 

 

 

 

Cap Shield

 

 

 

 

 

 

 

 

 

26 in.

 

 

13-7/8in.

9-1/2in.

 

 

 

 

 

(352 mm)

(241 mm)

 

 

 

660 mm

 

 

 

 

 

 

 

 

 

14 in.

 

 

 

 

 

DVP-HSM-B

 

(356 mm)

 

 

 

 

 

Extended Heat Shield

 

 

 

 

 

 

 

Figure 16.4 DVP vent components

 

 

DRC-RADIUS

 

 

 

 

 

Cap Shield

 

 

62

Heat & Glo •

6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

 

 

B. Vent Components Diagrams (continued)

7-3/8in.

(187 mm)

1-1/2in.

(38 mm)

17-3/4in.

14 in. (451 mm)

(356 mm)

12 in. (305 mm)

12 in.

DVP-TB1305 mm BasementVent Cap

 

7-1/4in.

 

(184 mm)

 

12-1/2in.

 

(318 mm)

 

5-1/4in.

 

(133 mm)

 

DVP-TVHW

PVK-80

VerticalTermination Cap (Highwind)

 

(Not compatible with Intellifire Plus™.) (For use with IPI and DSI appliances only.)

16-7/8in.

14 in.

(429 mm)

(356 mm)

 

7-1/4in.

1 in.

(184 mm)

(25 mm)

 

12 in.

 

14 in.

(305 mm)

 

 

7-1/8in.

(356 mm)

12-1/8in.

 

(181 mm)

 

(314 mm)

 

 

 

8-3/4in.

3/8 in. (10 mm)

 

1 in. (25 mm)

 

(222 mm)

 

 

 

 

7-3/4to10-3/8in.

 

1-5/8in.

(197 to 264 mm)

 

 

 

(41 mm)

 

 

 

DVP-FBHT

 

DVP-HPC

FireBrickTermination Cap

 

High Performance Cap

 

Figure 16.5 DVP vent components

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

63

B. Vent Components Diagrams (continued)

15 in.

(381 mm)

8-1/8in.

13 in.

Effective Length

 

 

(206 mm)

(330 mm)

5-1/2in.

8-3/8in.

5-3/4to8-3/8in.

 

 

 

 

146 to 213 mm

140 mm

213 mm

 

 

 

87°

 

 

 

 

10-1/2in.

267 mm

10-7/8in. 276 mm

WARNING

Fire Risk.

When using DVP-HRC-SSandDVP-HRC-ZC-SS termination caps on top vented fireplaces, a 6 inch minimum vertical vent section is required before installing first elbow.

DVP-HRC-SS

DVP-HRC-ZC-SS

HORIZONTAL TERMINATION CAP

13-5/8IN.

346 mm

12-1/2IN.

318 mm

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 ft. PV Wire Harness

PVI-WH10

20 ft. PV Wire Harness

PVI-WH20

40 ft. PV Wire Harness

PVI-WH40

60 ft. PV Wire Harness

PVI-WH60

80 ft. PV Wire Harness

PVI-WH80

100 ft. PV Wire Harness

PVI-WH100

20-3/4IN.

527 mm

PVI-SLP

Power Vent Inline

Note: Wire harnesses required to power thePVI-SLPconnect to the appliance and are ordered separately fromPVI-SLP.Contact your dealer to order.

12-1/2IN.

(318 mm)

Figure 16.6 Vent Components

 

16 IN.

 

406 mm

 

4-1/2IN.

 

114 mm

 

9-3/16IN.

 

(233 mm)

13-5/8IN.

16-11/16IN.

(346 mm)

424 mm

SLP-LPC

SLP Low Profile Cap

15 IN.

(381 mm)

16-11/16IN.

(424 mm)

64

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

B. Vent Components Diagrams (continued)

 

 

 

 

6-1/2in.

 

6-1/2in.

 

 

165 mm

 

 

 

 

 

165 mm

 

 

6-1/2in.

 

 

 

 

8-3/4in.

 

 

 

165 mm

 

 

 

9-1/4in.

222 mm

 

 

6 in.

 

 

235 mm

 

 

152 mm

 

 

6-5/8in.

 

 

 

 

168 mm

 

 

6-5/8in.

 

SLP45

 

 

 

 

 

168 mm

 

45° Elbow

 

 

 

 

 

 

 

 

 

 

9-7/8in.

 

 

 

 

251 mm

 

 

 

 

SLP90

 

 

 

 

90° Elbow

 

Effective Height/Length

 

 

Pipe

inches

mm

 

 

SLP4

4

102

 

 

SLP6

6

152

 

Effective

SLP12

12

305

 

Height/

SLP24

24

610

 

Length

SLP36

36

914

 

 

 

 

SLP48

48

1219

 

 

SLP6A

2 - 6

51-152

DVP-SLP24

 

SLP12A

2 - 12

51-305

Adapter

SLP PIPE

SLP-HVS

SLP-FS

SLP-WS

Horizontal Pipe

Ceiling Firestop

Wall Shield Firestop

Support

 

 

Figure 16.7 SLP Series Vent Components

 

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

65

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2in. (38 mm). The heat shield is designed to be used on a wall 4 in. to7-1/4in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than7-1/4in. (184 mm) aDVP-HSM-Bwill be required.

 

8 in.

 

 

 

 

(203 mm)

 

 

 

 

Heat

 

 

 

 

Shield

 

 

 

15-1/8in.

 

 

 

 

(384 mm)

 

 

 

 

 

 

Term Cap

Minimum

Maximum

 

 

Effective Length

Effective Length

 

Max

 

12 in.

Trap1

3-1/8in.

4-3/4in.

Effective

79 mm

121 mm

(305 mm)

Length

 

 

5-1/4in.

9-1/4in.

 

SLP-TRAP

Trap2

 

133 mm

235 mm

 

Horizontal Termination Cap

 

 

 

 

 

SLK-SNKD

SLP-CCS-BK

SLP-TVHW

Cathedral Ceiling

Vertical

Snorkel

Support Box-Black

Termination Cap

Termination Cap

 

 

 

 

26 in.

 

 

660 mm

DVP-2SL

DVP-HSM-B

Extended Heat Shield

Adapter

 

SLP-DCF-BK

SLP-WT-BK

Ceiling Firestop

Wall Thimble-Black

Black

 

Figure 16.8 SLP Series Vent Components

66

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

C. Service Parts

6000CMOD-IPI

 

 

 

 

36” Modern Direct Vent Fireplace

Beginning Manufacturing Date: Aug 2010

 

Ending Manufacturing Date:______

 

 

 

1

 

6

3

2

8

7

 

 

4

 

 

 

4.1

 

 

 

4.2

 

 

5

 

11

 

 

 

4.4

 

 

 

4.3

 

10

 

 

 

9

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

1

Non-CombustibleBoard

 

2166-136

 

2

Refractory Bracket

Qty 2 req

2241-115

 

3

Rock Fixture Assembly

 

2241-040

Y

4

Base Pan Assembly

 

2241-015

 

4

Base Pan Back

 

2241-114

 

4

Base Pan Front

 

2241-101

 

4

Pilot Hood

 

2241-117

 

4

Pilot Shield

Stainless

2241-116

 

5

Burner Assembly

NG

2241-007

Y

LP

2241-008

Y

 

 

6

Glass Refractory, Back

 

2241-200

 

7

Glass Refractory, Sides

Qty 2 req

2241-201

 

8

Glass Retainer Clips

Pkg of 25

060-235-25

Y

9

Surround Assembly

 

2166-019

 

10

Glass Assembly

 

GLA-6000G

Y

11

Junction box

 

4021-013

Y

Additional service part numbers on following page.

 

 

 

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

67

C. Service Parts

8000CMOD-IPI

 

 

 

 

42” Modern Direct Vent Fireplace

Beginning Manufacturing Date: Aug 2010

 

Ending Manufacturing Date:______

 

 

 

1

 

6

3

2

8

7

 

 

4

 

 

 

4.1

 

 

 

4.2

 

 

5

 

11

 

 

 

4.4

 

 

 

4.3

 

10

 

 

 

9

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

1

Non-CombustibleBoard

 

2170-136

 

2

Refractory Bracket

Qty 2 req

2241-115

 

3

Rock Fixture Assembly

 

2241-040

Y

4

Base Pan Assembly

 

2242-015

 

4

Base Pan Back

 

2242-114

 

4

Base Pan Front

 

2242-101

 

4

Pilot Hood

 

2241-117

 

4

Pilot Shield

Stainless

2241-116

 

5

Burner Assembly

NG

2242-007

Y

LP

2242-008

Y

 

 

6

Glass Refractory, Back

 

2242-200

 

7

Glass Refractory, Sides

Qty 2 req

2242-201

 

8

Glass Retainer Clips

Pkg of 25

060-235-25

Y

9

Surround Assembly

 

2170-019

 

10

Glass Assembly

 

GLA-950TR

Y

11

Junction box

 

4021-013

Y

Additional service part numbers on following page.

 

 

 

68

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

 

 

C. Service Parts

6000CMOD-IPI,8000CMOD-IPI

 

 

Beginning Manufacturing Date: Aug 2009

 

 

Ending Manufacturing Date: ______

#12 Valve Assembly

12.2

 

 

12.3

12.1

12.4

 

12.5

 

 

 

 

 

12.6

 

 

 

 

 

12.7

 

 

12.14

 

 

12.9

 

 

 

 

 

 

 

 

 

 

12.8

 

 

 

 

 

12.10 12.11

12.12

12.13

 

 

 

 

 

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

12.1

Shutter Bracket Assembly

 

 

2118-121

Y

12.2

Pilot Assembly, NG

 

 

2090-012

Y

Pilot Assembly, LP

 

 

2090-013

Y

 

 

 

12.3

Pilot Bracket

 

 

2241-109

 

12.4

3-HoleGrommet

 

 

2118-104

 

12.5

Valve Bracket

 

 

2118-104

 

12.6

Flex Ball Valve Assembly

 

 

302-320A

Y

12.7

Valve, NG

 

 

2166-302

Y

Valve, LP

 

 

2166-303

Y

 

 

 

12.8

Male Connector

Pkg of 5

 

303-315/5

Y

12.9

Bulkhead w/FlexTube

 

 

7000-156

Y

12.10

Control Module, Gray

 

 

2166-306

Y

12.11

Wire Harness

 

 

2166-304

Y

12.12

Switched DC Regulator

 

 

2166-305

Y

12.13

Jumper Wire

 

 

2187-198

Y

12.14

Thermostat Wire Assembly

 

 

2118-170

Y

 

Orifice, NG (#40C)

6000CMOD-IPI

582-840

Y

 

Orifice, LP (#55C)

582-855

Y

 

 

 

 

Orifice, NG (#35C)

8000CMOD-IPI

582-835

Y

 

Orifice, LP (#54C)

582-854

Y

 

 

 

Additional service part numbers on following page.

 

 

 

 

 

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

69

Service Parts List

6000CMOD-IPI,8000CMOD-IPI

IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement

 

Stocked

parts for your appliance please provide model number and serial number. All parts listed

 

in this manual may be ordered from an authorized dealer.

 

 

at Depot

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Battery Pack**

 

2166-323

Y

 

**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 500mA~10A 3/4” long

 

Flue Restrictor

 

385-128

 

 

Gasket Assembly

 

 

 

 

Includes Vent, Seal Cap, Burner Neck, Shutter Bracket,

 

2166-081

 

 

Manifold and Valve Plate gaskets

 

 

 

 

Glass Latch Assembly

Pkg of 2

386-122A/2

Y

 

Media, Standard, 7 lb bags

Clear (Qty 2 req)

4065-111

 

 

 

 

 

 

Amber

MEDIA-AMBER-14

 

 

Media (Optional 14 LB bag)

Black

MEDIA-BLACK-14

 

 

 

Cobalt (Blue)

MEDIA-COBALT-14

 

 

Touch Up Paint

 

TUP-GBK-12

 

 

Conversion Kit, NG

6000CMOD-IPI

N/A

 

 

Conversion Kit, LP

LPKI-6CM

Y

 

 

 

Conversion Kit, NG

8000CMOD-IPI

N/A

 

 

Conversion Kit, LP

LPKI-8CM

Y

 

 

 

Pilot Orifice, NG

 

593-528

Y

 

Pilot Orifice, LP

 

593-527

Y

 

Regulator, NG

 

NGK-DXV-50

Y

 

Regulator, LP

 

LPK-DXV-50

Y

70

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

D. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th Street West, Lakeville, MN 55044 www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating

• Read, understand and follow

and maintenance

these instructions for safe

instructions included.

installation and operation.

Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

2000-945

Printed in U.S.A. - Copyright 2012

Heat & Glo • 6000CMOD-IPI,8000CMOD-IPI2241-900Rev. H • 5/12

71