Heat & Glo LifeStyle 6000TRS-CE User Manual

Size:
3.31 Mb
Download

Model:

6000TRS-CE

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

What to do if you smell gas

-Do not try to light any appliance

-Do not touch any electrical switch. Do not use any phone in your building.

-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

This is a room sealed appliance and no other ventilation is required than what is provided.

Please contact your Heat & Glo dealer with any questions or concerns. For the number of your nearest Heat & Glo dealer, please visit www.heatnglo.com.

Printed in U.S.A. Copyright 2011

Heat & Glo, a brand of Hearth & Home Technologies Inc. 7571 215th Street West, Lakeville, MN 55044, USA

Installers Guide

0086

Î

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled • NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS INSTALLERS GUIDE MUST BE LEFT WITH APPLIANCE FOR FUTURE REFERENCE.

These instructions are only valid if the following country symbol is on the appliance. If this symbol is not present on the appliance, it is necessary to refer to the technical instructions which will provide the necessary information concerning the modification of the appliance to the conditions of use for the country.

These instructions are valid for the following countries: GB, IE

This product is covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112,

5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

1

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

SAFETY AND WARNING INFORMATION

!

!

!

!

!

!

!

!

!

READ andUNDERSTAND all instructions carefully before starting the installation.FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty.

Prior to the first firing of the fireplace, READ the Using Your Fireplace section of theUsers Guide.

DO NOT USE this appliance if any part has been under water. ImmediatelyCALL a qualified service technician to inspect the unit and to replace any part of the control system and any gas control which has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a qualified service person. The appliance and flue system should beINSPECTED before initial use and at least annually by a professional service person.

Always KEEP the appliance clear and free from combustible materials, petrol, and other flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the applianceCLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should be LOCATED out of traffic areas and away from furniture and draperies. Clothing or flammable materialSHOULD NOT BE PLACED on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature and shouldSTAY AWAY to avoid burns or clothing ignition. Young children should beCAREFULLY SUPERVISED when they are in the same room as the appliance.

!These units MUST use one of the fluing systems described in the Installing the Fireplace section of theInstallers Guide.NO OTHER flue systems or componentsMAY BE USED.

!This gas appliance and flue assembly MUST be vented directly to the outside andMUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas applianceMUST USE a separate flue system. Common flue systems arePROHIBITED.

!

!

!

!

!

!

!

!

INSPECT the external terminal cap on a regular basis to make sure that no debris is interfering with the air flow.

The glass door assembly MUST be in place and sealed, and the trim door assemblyMUST be in place on the appliance before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door removed, cracked, or broken. Replacement of the glass door should be performed by a licensed or qualified service person.DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied by the gas appliance manufacturer.NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door assembly.DO NOT ATTEMPT to clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified service technician perform an appliance check-upat the beginning of each heating season.

Any safety screen or guard removed for servicing must be replaced before operating this appliance.

This appliance is intended for use on a gas installation with a governed meter.

2

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Safety and Warning Information ...................................

2

Service Parts List ...........................................................

4

Section 1: Approvals and Regulations.........................

7

Appliance Certification..................................................

7

Installation Regulations ................................................

7

Section 2: Getting Started .............................................

8

Introducing the Heat & Glo Gas Fireplaces..................

8

Pre-installationPreparation ..........................................

8

Section 3: Installing the Fireplace ..............................

10

Step 1

Locating the Fireplace ..................................

10

Step 2

Framing the Fireplace...................................

11

Step 3

Installing the Flue System.............................

12

 

A. Flue System Approvals.............................

12

 

B. Installing Flue Components......................

20

 

C. Flue Termination.......................................

24

Step 4

Positioning, Leveling and

 

 

Securing the Fireplace..................................

29

Step 5

The Gas Control Systems.............................

29

Step 6

The Gas Supply Line ....................................

30

Step 7

Gas Pressure Requirements ........................

31

Step 8

Wiring the Fireplace......................................

31

Step 9

Finishing .......................................................

32

Step 10

Installing Trim, Logs & Ember Material ............

33

 

Installing the Trim..........................................

33

 

Positioning the Logs .....................................

34

 

Placing the Ember Material...........................

36

Step 11

Before Lighting the Fireplace........................

37

Step 12

Lighting the Fireplace ...................................

38

 

After the Installation .....................................

38

Section 4: Maintaining and Servicing

 

 

Your Fireplace ............................................

39

Section 5: Troubleshooting .........................................

41

Limited Lifetime Warranty...............................................

44

Î = Contains updated information.

Table of

Contents

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

3

Service Parts

6000TRS-CE

 

 

36” Direct Vent Gas Fireplace

Beginning Manufacturing Date: Jan 2004

 

Ending Manufacturing Date: ______

 

 

9

 

 

8

 

 

10

 

 

11

 

 

12

15

14

7

13

16

 

6

17

18

19

Log Set Assembly

4

 

1

 

2

3

5

Part number list on following page.

4

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Service Parts List

6000TRS-CE

IMPORTANT THIS IS DATED INFORMATION: When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

 

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

 

 

Log Set Assembly

 

LOGS-6TRSCE

 

1

Log #1

 

SRV2049-700

 

2

Log #2

 

SRV2049-701

 

3

Log #3

 

SRV385-723

 

4

Log #4

 

SRV385-721

 

5

Log #5

 

SRV385-722

 

6

Junction Box

 

546-250A

 

 

Refractory Kit

 

BRICK-6000-FB

 

7

Refractory, Right

 

SRV2027-372

 

8

Refractory, Back

 

SRV2027-370

 

9

Refractory, Left

 

SRV2027-371

 

10

Exhaust Baffle

 

2049-101

 

11

Grate

 

2049-020

 

 

Burner Assembly N

 

2049-010

 

12

Burner Assembly P

 

2049-012

 

 

Burner Assembly B

 

2049-014

 

13

Base Refractory

 

2049-102

 

14

Glass Door Assembly

 

GLA-6TRXI

 

15

Insulation Board

 

385-401

 

16

Surround

Pre Aug 2009

SRV2101-260

 

Post Aug 2009

2166-019

 

 

 

 

17

Top Louver

 

392-182A

 

18

Dress Guard

 

392-180A

 

19

Hood

 

SRV60-143-BK

 

 

Gasket Assembly

 

 

 

 

Contains Burner neck, shutter bracket, vent, seal cap, and valve

 

2166-081

 

 

plate gaskets

 

 

Î

 

Glass Latch Assembly

Pkg of 2

33858/2

 

 

High Temp Limit Switch

 

046-018A

 

 

Exhaust Restrictor

 

530-299

 

 

Mineral Wool

 

050-721

 

 

Touch-UpPaint

 

TUP-GBK-12

 

 

Conversion Kits

 

 

 

 

Natural to Propane

 

NGK-6TRS-CE

 

 

Propane to Butane

 

LPK-6TRS-CE

 

 

Butane to Propane

 

BGK-6TRS-CE

 

 

Regulator N

 

230-1570

 

 

Regulator P/B

 

230-1520

 

 

Pilot Orifice N

 

529-512

 

 

Pilot Orifice P/ B

 

200-2630

Additional service part numbers appear on following page.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

5

Service Parts

6000TRS-CE

Valve Assemble Parts List

Beginning Manufacturing Date: Jan 2004

 

Ending Manufacturing Date: ______

20.1

Valve Assembly

20.2

20.3

20.4

20.6

20.5

20.7

20.8

20.9

20.10 20.11

IMPORTANT THIS IS DATED INFORMATION: When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

20.1

Pilot Assembly N

 

529-550A

Pilot Assembly P/B

 

529-551A

 

 

20.2

Pilot Bracket

 

2049-105

 

Orifice N (#33C)

 

582-833

20.3

Orifice P (1.8 MM)

 

582-818

 

Orifice B (#52C)

 

582-852

20.4

12” Flex

 

383-302A

20.5

Valve Bracket

 

2118-104

20.6

Flex Assembly

 

302-330A

20.7

Piezo Ignitor

 

291-513

20.8

Wire Assembly

 

049-552A

20.9

On/ Off Rocker Switch

 

060-521A

20.10

Valve N

 

060-524

Valve P

 

060-526

 

 

20.11

Male Connector

Pkg of 5

303-315/5

6

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Appliance Certification

The Heat & Glo fireplace models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories.

 

MODEL

LABORATORY

TYPE

CERTIFICATION STANDARD

Î

6000TRS-CE

BSI

Gas Fireplace

BS EN 613:2001 (Amd 1)

Installation Regulations

Before installation check that local distribution conditions, nature of gas and pressure, and adjustment of the appliance are compatible.

This appliance must be installed with the rules in force, and used only in a sufficiently ventilated space. Consult instructions before installation and use of this appliance.

1

Approvals and Regulations

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

7

 

 

Introducing the

 

 

Heat & Glo

 

 

Gas Fireplaces

Getting

 

Pre-installation

Started

 

Preparation

2

 

 

 

 

Heat & Glo direct flue gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems.

Gas fireplace diagrams, including the dimensions, are shown in this section.

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass.Do not install any unit with damaged, incomplete, or substitute parts.

The flue system components and trim doors are shipped in separate packages. The gas logs are packaged separately and must be field installed.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and may present a fire hazard.

The Heat & Glo Fireplace Products, Inc. Warranty will be voided by, and Heat & Glo Fireplace Products, Inc. disclaims any responsibility for, the following actions:

Installation of any damaged fireplace or flue system component.

Modification of the fireplace or direct flue system.

Installation other than as instructed by Heat & Glo Fireplace Products, Inc.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not manufactured and approved by Heat & Glo Fireplace Products, Inc., not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

8

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

When planning a fireplace installation, it’s necessary to determine:

Where the unit is to be installed.

The flue system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

L

 

M

 

C

 

L

J

 

N

K

 

TOP VIEW

 

 

GAS LINE

 

H

 

 

C

 

ACCESS

 

L

 

R

 

I

 

C

D

 

 

 

 

 

G

 

O

Q

E

 

 

P

 

B

F

 

A

 

 

 

LEFT SIDE

 

FRONT VIEW

RIGHT SIDE

Location

Centimeters

A

104,1

B

91,8

C

85,1

D

87,9

E

57

F

24,6

G

68,3

H

15,2 dia

I

101,9

Location

Centimeters

J

54,6

K

29,7

L

72,4

M

36,2

N

21,6

O

73

P

21,6

Q

25

R

91,8

Figure 1. Diagram of the 6000TRS-CE

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

9

3

Installing the

Fireplace

10

Step 1

 

The diagram below shows space and clearance

Locating the

 

requirements for locating a fireplace within a room.

Fireplace

 

 

NOTE: THE REAR STANDOFF MAY NEED

 

TO BE REMOVED WHEN VENTING AT 45º

 

G

A

 

 

 

1,3 cm

 

 

 

 

B

 

 

ALCOVE

A

 

INSTALLATION E

BC

 

 

 

 

TOP FLUE

 

 

ONE 90º ELBOW

 

 

 

 

REAR FLUE,

 

 

REAR FLUE

 

 

I

 

 

 

HORIZONTAL TERMINATION

 

 

 

 

 

 

REAR FLUE

ONE 90º ELBOW

 

 

 

 

 

TWO 90º ELBOWS

 

 

 

 

 

 

B

 

 

B

 

C

 

 

 

 

 

NO ELBOWS

 

 

 

D

 

 

 

 

B

 

 

 

L

D

 

 

 

 

 

 

F

 

 

 

 

 

H

 

 

 

 

 

 

D

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

B

C

D

 

E

F

G

H

I

cm

130

107

183

144

See Section F.

56

45

20

73

Mantel Projections

 

 

 

 

 

 

 

 

 

Figure 2. Fireplace Dimensions, Locations, and Space Requirements

 

 

 

Clearance Requirements

The top and back of the fireplace are defined by stand-offs.

The minimum clearance to a perpendicular wall extending past the face of the fireplace is 7.62 cm.

The back of the fireplaces may be recessed into combustible construction (see Figure 3).

 

MODEL: 6000TRS-CE

 

RECESSED DEPTH: 54.6 cm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum Clearances from the Fireplace to Combustible Materials

 

 

 

 

Glass

 

Floor

 

 

Back of

Sides of

 

Top of

 

Ceiling

 

 

 

 

Front

 

 

 

Fireplace

Fireplace

 

Fireplace

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

91.4 cm

 

0

 

 

 

1.3 cm

 

1.3 cm

 

8.9 cm

 

 

79 cm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum Clearances from the Flue Pipe to Combustible Materials

 

 

 

For Horizontal Sections

 

For Vertical

 

 

At Wall Firestops

 

 

 

Top

 

Bottom

 

Sides

 

Sections

 

Top

Bottom

 

Sides

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7.6 cm

 

2.54 cm

 

2.54 cm

 

2.54 cm

 

6.4 cm

1.3 cm

 

2.54 cm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3. Minimum Clearances

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Step 2

Framing the

Fireplace

CAUTION

Fireplace framing can be built before or after the fireplace is set in place. Framing should be positioned to accommodate wall coverings and fireplace facing material. The diagram below shows framing reference dimensions.

MEASURE FIREPLACE DIMENSIONS, AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINS.

WALL

STUD

14 cm

D* E*

B *

C

Framing should be constructed of 2 X 4 lumber or heavier.

A

8 cm

NON-COMBUSTIBLEZONE

* Note: DimensionB taken from fin-

 

ished hearth frame. Dimensions D

IS DEFINED BY 8 CM ABOVE

 

THE ELBOW FOR THE ENTIRE

and E taken from bottom of unit.

WIDTH AND DEPTH (BEHIND

 

 

 

THE FRONT HEADER) OF

 

 

 

THE FIREBOX.

 

 

 

 

A

B

C

D

E

107 cm

102 cm

56 cm

68,3 cm

106 cm

Figure 4. Framing Dimensions

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

11

Step 3

Installing the

Flue System

A. Flue System Approvals

These models have flue starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of starting collars will be used to attached the flue system. The starting collar sealing cap must remain on the starting collar NOT used.

These models use DVP-seriesdirect flue components when using theTOP and REAR flue collars.

Approved flue system components are labeled for identification.

NO OTHER FLUEING SYSTEMS OR COMPONENTS MAY BE USED. Detailed installation instructions are included with each flue termination kit and should be used in conjunction with this Installers Guide. Figure 4 shows flue system components and terminations.

Identifying Flue Components

The flue systems installed on this gas fireplace may include one, two, or three 90°elbow assemblies. The relationships of vertical rise to horizontal run in flue configurations using 90° elbows MUST BE strictly adhered to. The rise to run relationships are shown in the flueing drawings and tables on the next several pages.

Note: Two 45° elbows may be used in place of one 90° elbow. YouMUST always maintain theMAXIMUM andMINIMUM rise-to-runratios in the flue system when using 45° elbows.

 

VERTICAL

STORM COLLAR

 

TERMINATION

 

 

 

HORIZONTAL

 

 

ROOF FLASHING

 

 

 

 

 

TERMINATION

 

 

 

 

 

 

 

HORIZONTAL PIPE

 

 

 

 

SUPPORT

 

 

 

 

PIPE LENGTH

 

WALL FIRESTOP

 

 

 

 

 

90 DEGREE

 

 

 

 

ELBOW

CEILING

 

 

 

 

WALL BRACKET

 

 

 

FIRESTOP

 

 

 

 

 

FLUE SYSTEM TERMINATION KITS

 

 

 

DVP-SERIES

 

 

 

DVP-TVHW

DVP-TRAP

 

 

 

Figure 5. Flue Components and Terminations

 

 

12

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

 

10.2 cm

15.2 cm

30.5 cm

DVP4

DVP6

DVP12

36.2 cm

31.0 cm

5.1 cm

MAX.

MIN.

 

 

61.0 cm

DVP12A

91.4 cm

20

 

.

 

3

 

cm

 

 

121.9 cm

25.1 cm

DVP24

45.0º

 

26 cm

 

26 cm

 

DVP45

DVP36

 

28.6 cm

 

18.4 cm

 

3.2 cm TYP

 

DVP48

21.7 cm

1.3 cm TYP

31.9 cm

 

DVP90ST

 

NOTE: PIPES OVERLAP 3,2 cm AT EACH JOINT.

Figure 6. DVP-SeriesBalanced Flue Component Specifications (127 mm inner pipe / 203 mm outer pipe)

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

13

CAP

STRAIGHT UP

VERTICAL FLUE

V

11.8 m MAX.

V

 

Figure 7. Straight up Vertical Flue

 

STRAIGHT OUT HORIZONTAL FLUE

 

H

H

 

MIN. RUN

MAX. RUN

 

13.1” (33.2 cm)

24” (61.0 cm)

 

 

H

 

Figure 8. Straight Out Horizontal Flue

14

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

V

H

FLUE WITH ONE (1) 90o ELBOW

V

H

MIN. 30.5 cm

MAX. 61.0 cm

MIN. 61.0 cm

MAX. 1.22 m

MIN. 91.4 cm

MAX. 1.86 m

MIN. 1.22 m

MAX. 2.48 m

MAX. 7.3 m

MAX. 2.48 m

Figure 9. Flue with One 90° Elbow

FLUE WITH ONE (1) 90o ELBOW

V

H

MIN. 30.5 cm

MAX. 1.22 m

MIN. 61.0 cm

MAX. 2.4 m

MIN. 91.4 cm

MAX. 3.7 m

MIN. 1.22 m

MAX. 4.9 m

V + H = MAX 7.3 m

H = MAX. 2.4 m

 

H

V

NOTE: For corner installations: A 15.2 cm MINIMUM length of straight pipe must be first attached to the fireplace before 90o elbow. This will allow the flue pipe to clear the top standoffs.

NOTE: If a 90º elbow is first attached to the unit, the maximum horizontal run is 3 feet (91.4 cm).

Figure 10. Flue with One 90° Elbow

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

15

 

FLUE WITH TWO (2) 90° ELBOWS

V

H

H + H1

MIN. 30.5 cm MIN. 61.0 cm MIN. 91.4 cm MIN. 1.22 m MAX. 6.1 m

MAX. 61.0 cm MAX. 61.0 cm MAX. 1.22 m MAX. 1.8 m MAX. 1.8 m

MAX. 1.22 m MAX. 2.48 m MAX. 3.72 m MAX. 4.9 m MAX. 4.9 m

H1

V

H

Figure 11. Flue with Two 90° Elbows

16

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

H1

V

H

FLUE WITH TWO (2) 90° ELBOWS

V

MIN. 30.5 cm MIN. 61.0 cm MIN. 91.4 cm MIN. 1.22 m

H + H1

MAX. 1.22 m MAX. 2.4 m MAX. 3.7 m MAX. 4.9 m

V+H+H1= MAX. 11.8 m H+H1= MAX. 4.9 m

V+V1+H1= MAX. 12.97 m

V1

V

H

Figure 12. Flue with Two 90° Elbows

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

17

 

FLUE WITH THREE (3) 90° ELBOWS

V

H

H + H1

MIN. 30.5 cm

MAX. 61.0 cm

MIN. 61.0 cm

MAX. 1.22 m

MIN. 91.4 cm

MAX. 1.86 m

MIN. 1.22 m

MAX.

2.48 m

H = MAX. 2.48 m

MAX.

4.9 m

MAX. 1.22 m MAX. 2.48 m MAX. 3.6 m MAX. 4.9 m

NOTE: V + V1 + H + H1 = MAX. 10.97 m

V1

V

H1

 

FLUE WITH THREE (3) 90° ELBOWS

V

H

H + H1 + H2

MIN. 30.5 cm MIN. 61.0 cm MIN. 91.4 cm MIN. 1.22 m MAX. 6.1 m

MAX. 61.0 cm MAX. 61.0 cm MAX. 1.22 m MAX. 1.86 m MAX. 1.86 m

MAX. 1.22 m MAX. 2.48 m MAX. 3.6 m MAX. 4.9 m MAX. 4.9 m

V

H2

H1

Figure 13. Flue with three 90° elbows

18

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

FLUE WITH THREE (3) 90° ELBOWS

V

MIN. 30.5 cm MIN. 61.0 cm MIN. 91.4 cm MIN. 1.22 m

H + H1

MAX. 1.22 m MAX. 2.4 m MAX. 3.7 m MAX. 4.9 m

V + V1 + H + H1 = MAX. 10.97 m

H + H1 = MAX. 4.9 m

H1

V1

V

H

V1

H1

V

H

FLUE WITH THREE (3) 90° ELBOWS

V

H + H1

MIN. 30.5 cm MIN. 61.0 cm MIN. 91.4 cm MIN. 1.22 m

MAX. 1.22 m MAX. 2.4 m MAX. 3.7 m MAX. 4.9 m

V + V1 + H + H1 = MAX. 10.97 m

H + H1 = MAX. 4.9 m

Figure 14. Flue with three 90° elbows

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

19

B. Installing Flue Components

After determining which set of starting collars will be used (top or rear), follow venting instructions accordingly.

Venting Out the Rear Flue

Remove the installed rear seal cap from the rear starting collars by cutting the strap at each end (See Figure 15). Follow the flue configuration tables accordingly.

Remove the 12.7 cm diameter heat shield from the 1.27 cm diameter collar by sliding it out. Remove insulation piece.

!WARNING: THE TOP HEAT SHIELD (INSIDE THE FIREBOX) MUST REMAIN ATTACHED IF THE FLUE SYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE 15.

Venting Out the Top Flue

Remove the top flue collar seal cap by cutting the strap on each end. Remove both pieces of insulation inside the top two starting collars (see Figure 15).

Remove the 10.2 cm diameter heat shield from the 10.2 cm diameter collar by sliding it out.

You have to take the glass off again for positioning the logs when the unit is finally installed in place and finished around it. Reinstall the glass door. Attach flue system to the top starting collars.

!WARNING: THE REAR FLUE COLLAR SEAL CAP MUST REMAIN ATTACHED TO THE REAR FLUE COLLARS IF THE FLUE SYSTEM IS ATTACHED TO THE TOP STARTING COLLARS. SEE FIGURE 15.

!WARNING: FAILURE TO REMOVE INSULATION IN THE SET OF COLLARS YOU ARE USING COULD CAUSE A FIRE.

!WARNING: YOU MUST LEAVE THE INSULATION IN PLACE IN THE SET OF COLLARS YOU ARE NOT USING.

Insert screwdriver or similar object here to remove cap.

Venting

Venting

Out Rear

Out Top

SEAL

SEAL

INSULATION,

CAP

DISCARD

CAP

 

BOTH

 

 

PIECES

HEAT

 

 

SHIELD

 

 

DISCARD

HEAT

 

SHIELD

 

INSULATION

 

 

CUT HERE

Figure 15

20

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Installing Flue Components

1. Attaching the First Flue Component to the Starting Collars:

A. On the REAR of the heater

To attach the first flue component to the starting collars on the rear of the heater make sure that the heater gasket supplied with the heater seals between the first flue component and the outer heater wrap.

The first 90° elbow installed in the flue system of a rear flueing heater MUST BE in a vertical position.

B. On the TOP of the heater

To attach the first flue component to the starting collars on the top of the heater:

Slide the male end of the inner flue of the pipe section into the inner collar on the heater. At the same time, insert the outer flue into the outer collar on the heater. Push the flue section into

the appliance collar until all the lances (see Figure 16) have snapped in place. Tug slightly on the flue to confirm that it has completely locked into place.

Slide the ceramic fiber pad over the first flue section and place it flush to the fireplace. Continue to add vent components.

Figure 16.

WARNING: ENSURE THAT THE HEATER GASKET SUPPLIED WITH THE HEATER SEALS BETWEEN THE FIRST FLUE COMPONENT AND THE OUTER HEATER WRAP.

C. Continue Adding Flue Components

To continue adding flue components in accordance with the pre-plannedflue system configuration:

Ensure that each succeeding flue component is securely fitted and locked into the preceding component in the flue system. NOTE: Make sure that seams areNOT aligned to prevent unintentional disconnection.

For elbows that are changing the flue direction, two screws minimum should be put in the outer flue at the joint to prevent the elbow from rotating.

2. Install Support Brackets

For Horizontal Runs - The flue system must be supported every five (5) feet (152.4 cm) of horizontal run by a horizontal pipe support.

To install support brackets for horizontal runs:

Place the pipe supports around the flue pipe.

Nail the pipe supports to the framing members.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

21

For Vertical Runs - The flue system must be supported every 240 cm above the heater flue outlet by wall brackets.

To install support brackets for vertical runs:

Attach wall brackets to the flue pipe and secure the wall bracket to the framing members with nails or screws.

WALL BRACKET

WALL STUD

2,4 m

FLUE

OUTLET

2,5 cm MINIMUM

Figure 17. Installing Support Brackets

3. Install Firestops

For Horizontal Runs - Firestops are REQUIREDon both sides of a combustible wall through which the flue passes.

To install firestops (heat shield) for horizontal runs that pass through either interior or exterior walls:

Cut a 25,4 cm X 30,5 cm hole through the wall.

Position the firestops on both sides of the hole previously cut and secure the firestops with nails or screws.

The pipe opening of the firestops MUST BE placed towards the bottom of the firestop.

Continue the flue run through the firestop.

22

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

10" (25.4 cm)

INTERIOR

WALL SHIELD

12" (30.5 cm)

Figure 18. Flue Pipe & Firestop

For Vertical Runs - One firestop is REQUIREDat the hole in each ceiling through which the flue passes.

To install firestops for vertical runs that pass through ceilings:

Position a plumb bob directly over the center of the vertical flue component.

Mark the ceiling to establish the center point of the flue.

Drill a hole or drive a nail through this center point.

Check the floor above for any obstructions, such as wiring or plumbing runs.

Reposition the heater and flue system, if necessary, to accommodate the ceiling joists and/or obstructions.

Cut a 25.4 cm X 30.5 cm hole through the ceiling, using the firestop pipe opening as a guide.

Frame the hole with framing lumber the same size as the ceiling joists.

10" (25.4 cm)

10” (25.4 cm)

 

 

CHIMNEY

 

HOLE

NEW

EXISTING CEILING

JOISTS

FRAMING

 

MEMBERS

 

CEILING

 

Figure 19. Hole and New Framing Members

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

23

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

Figure 20. Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NAILS (4 REQUIRED)

RAFTER

 

CEILING

 

CEILING FIRESTOP

 

 

 

Figure 21. Attic Firestop

 

C. Flue Termination

CAUTION:

IF EXTERIOR WALLS ARE FINISHED WITH VINYL SID-

 

ING, IT IS NECESSARY TO INSTALL THE VINYL PRO-

 

TECTOR KIT (VPK-DV)TO THE TOP OF THE EXTERIOR

 

FIRESTOP FOR ALL ROUND TERMINATION CAPS.

 

For Horizontal Terminations using the DVP-TRAP

 

To attach and secure the termination to the last section of

 

horizontal flue:

 

• The rear flue heat shield MUST be placed 2.54 cm above

 

the top of the flue between the wall shield and the base

 

of the termination cap.

 

• One section of the heat shield is attached to the wall

 

shield. The other is attached to the termination cap in the

 

same manner (see Figure 22).

24

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

The heat shield sections will overlap to match the wall thickness (depth). The small leg in the shield rests on top of the flue to properly space it from the pipe section (see Figure 22).

Interior

Rear Vent

Wall Shield

Heat Shield

 

3.8 cm min.

 

overlap

Outer Flue

 

Inner Flue

3.8 cm min.

 

 

Overlap

INTERIOR

EXTERIOR

 

Figure 22. Venting through the Wall

The termination kit should pass through the wall firestops from the exterior of the building.

Adjust the termination cap to its final exterior position on the building and interlock the flue sections.

WARNING: THE TERMINATION CAP MUST

!BE POSITIONED SO THAT THE ARROW IS POINTING UP.

Use a high-temperaturesealant gasket to seal between the pipe and exterior firestop.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

25

Figure 23 DVP Termination Cap

For Vertical Terminations - To locate the flue and install the flue sections:

Locate and mark the flue center point on the underside of the roof, and drive a nail through the center point.

Make the outline of the roof hole around the center point nail.

The size of the roof hole framing dimensions depend on the pitch of the roof. There MUST BE a 2.5 cm clearance from the vertical flue pipe to combustible materials.

Mark the roof hole accordingly.

Cover the opening of the installed flue pipes.

Cut and frame the roof hole.

Use framing lumber the same size as the roof rafters and install the frame securely. Flashing anchored to the frame must withstand heavy winds.

Continue to install concentric flue sections up through the roof hole and up past the roof line until you reach the appropriate distance above the roof.

To seal the roof hole, and to divert rain and snow from the flue system:

Attach a flashing to the roof using nails, and use a nonhardening mastic around the edges of the flashing base where it meets the roof.

Attach a storm collar over the flashing joint to form a water-tightseal. Placenon-hardeningmastic around the joint, between the storm collar and the vertical pipe.

Slide the termination cap over the end of the flue pipe and snap into place.

26

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

 

WARNING:FOLLOW NATIONAL REGULATIONS

 

AND CODES OF PRACTICE FOR MINIMUM CLEAR-

 

ANCES FROM GAS TERMINALS, AND PLACE-

 

MENT OF GAS TERMINAL.

NOTE

This also pertains to vertical flue systems installed on

 

the outside of the building.

51 cm

VERTICAL

WALL

LOWEST

DISCHARGE

OPENING

TERMINATION

CAP

X

30,5 cm

ROOF PITCH

IS X/ 30,5 cm

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Angle

H (Min.) M

0°-26.6°

............................................... 0.30*

26.6°-30.3° ...............................................

0.38*

30.3°-33.7° ...............................................

0.46*

33.7°-36.9° ...............................................

0.61*

36.9°-39.8° ...............................................

0.76

39.8°-42.5° ...............................................

0.99

42.5°-45.0° ...............................................

1.22

45.0°-49.4° ...............................................

1.52

49.4°-53.1° ...............................................

1.83

53.1°-56.3° ...............................................

2.13

56.3°-59.0° ...............................................

2.29

59.0°-60.3° ...............................................

2.44

*.91 M minimum in snow regions

Figure 24. Minimum Height from Roof to Lowest Discharge

Opening

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

27

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Q

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See Notes 3 & 4

 

 

(See Note 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S

 

Electrical

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

Service

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

= VENT TERMINAL

X = AIR SUPPLY INLET

 

 

 

 

= AREA WHERE TERMINAL IS NOT PERMITTED

 

V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

=

 

30.5 cm .................

clearances above grade, veranda,

 

K

 

=

91.4 m.....................

 

clearance to a mechanical

 

 

 

 

 

(See Note 1)

porch, deck or balcony

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(powered) air supply inlet

 

 

 

 

 

 

 

 

 

L

 

=

2.1 m

 

clearance above

paved

B

=

 

30.5 cm

clearances to window or door

 

 

 

 

 

 

 

 

 

 

(See Note 1)

 

sidewalk or a paved driveway

 

 

 

 

 

 

that may be opened, or to perma-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

located on public property

 

 

 

 

 

 

nently closed window. (Glass)

 

M*

 

=

50.8 cm ...................

 

clearance under veranda, porch,

D*

=

 

50.8 cm

vertical clearance to unventilated

 

 

 

 

 

 

 

 

 

 

 

 

 

 

deck, balcony or overhang

 

 

 

 

 

 

 

 

 

 

118.9 m

 

vinyl

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

soffit or to ventilated soffit located

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

above the terminal

 

S

=

15.3 cm....................

 

clearance from sides of elec-

 

 

 

 

 

84.8 cm

for vinyl clad soffits and below

 

 

 

 

 

(See Note 5)

 

trical service

 

 

 

 

 

 

 

 

 

 

 

T

=

30.5 cm

 

clearance above electrical

 

 

 

 

 

 

electrical service

 

 

F

=

 

22.9 cm

clearance to outside corner

 

 

 

 

 

(See Note 5)

 

service

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

=

 

15.3 cm

clearance to inside corner

 

 

 

Alcove Applications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

N

 

=

 

 

15.3 cm

 

non-vinylsidewalls

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H

=

 

91.4 cm .................

not to be installed above a gas

 

 

 

 

 

 

 

 

30.5 cm ..................

 

vinyl sidewalls

 

 

 

 

 

 

 

 

 

 

 

meter/regulator assembly within

 

 

P

 

=

 

 

2.4 m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

91.4 cm horizontally from the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

center-lineof the regulator

 

 

 

 

 

 

 

 

 

 

 

 

 

QMIN

 

 

RMAX

 

 

 

 

 

I

=

 

91.4 m ...................

clearance to gas service regulator

 

 

 

 

1 cap

 

.91 m

 

 

2 x Q ACTUAL

 

 

 

 

 

 

 

 

 

flue outlet

 

 

 

 

2 caps

 

1.8 m

 

 

1 x Q ACTUAL

 

 

 

J

=

22.9 cm

clearance to non-mechanical

 

 

 

 

3 caps

 

2.7 m

 

2/3 x Q ACTUAL

 

 

 

 

 

 

 

4 caps

 

 

3.7 m

 

 

1/2 x Q ACTUAL

 

 

 

 

 

 

 

 

 

air supply inlet to building or the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

combustion air inlet to any other

 

 

 

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

 

 

 

 

 

 

 

 

 

appliance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor, or meets Note 2.

NOTE 1: On private property where termination is less than 2.1 M above a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap shield is suggested. (See vents components page)

NOTE 2: Termination in an alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions specified for vinyl ornon-vinylsiding and soffits.1. There must be 91.4 cm minimum between termination caps.2. All mechanical air intakes within 3.0 M of a termination cap must be a minimum of 91.4 cm below the termination cap.3. All gravity air intakes within 91.4 cm of a termination cap must be a minimum of 30.5 cm below the termination cap.

NOTE 3: Local codes or regulations may require different clearances.

NOTE 4: Termination caps may be hot. Consider their proximity to doors or other traffic areas.

NOTE 5: Location of the vent termination must not interfere with access to the electrical service.

NOTE: Vent system termination is permitted in porch areas with two or more sides open. You must follow all side walls, overhang and ground clearances as stated in the instructions.

Heat & Glo assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

Figure 25 Vent Termination Minimum Clearances

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

28

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Step 4

Positioning,

Leveling, and

Securing the

Fireplace

1.Place the fireplace into position.

2.Level the fireplace from side to side and from front to back.

3.Shim the fireplace with non-combustiblematerial, such as sheet metal, as necessary.

4.Secure the fireplace to the framing by nailing or screwing.

Step 5

The Gas Control

System

The diagram below shows how to properly position, level, and secure the fireplace.

NAILING TABS

(BOTH SIDES)

Figure 26. Proper Positioning, Leveling, and Securing of a

Fireplace

!WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Standing Pilot Ignition System

This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor.

!WARNING: 230 VAC MUST NEVER BE CONNECTED TO A CONTROL VALVE IN A MILLIVOLT SYSTEM.

STANDING PILOT

Figure 27. Gas Control System

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

29

Step 6

The Gas

Supply Line

Note: Have the gas supply line installed by a qualified service technician in accordance with all building regulations.

Note: Before the first firing of the fireplace, the gas supply line should be purged of any trapped air.

NOTE: Consult local building regulations to properly size the gas supply line leading to the (Rp 1/2”) hook-upat the unit.

This gas inlet connection is ISO 7-Rp1/2 (BSP Rp 1/2).

To install the gas supply line:

When attaching the pipe, support the control so that the lines are not bent or torn.

After the gas line installation is complete, use a soap solution to carefully check all gas connections for leaks.

The gas line should be installed by a qualified service technician.

!WARNING: DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

At the gas line access hole, use insulation to repack the space around the gas pipe.

Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing.

GAS LINE

ACCESS

Figure 28

30

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Step 7

Gas Pressure

Requirements

Pressure requirements for Heat & Glo gas fireplaces are shown in the table below.

 

Natural Gas

Propane

Butane

Natural Gas

 

(G20)

(G31)

(G30)

(G25)

Inlet Pressure

20 mbar

37 or 50 mbar

30 or 50 mbar

25 mbar

Manifold Pressure

4-8.7mbar

15.7-25mbar

15.7-25mbar

4-8.7mbar

Gas Rate

.54 m3/h

.24 m3/h

.16 m3/h

.54 m3/h

Max. Input(NETCV)

10.0 kW

10.0 kW

9.5 kW

8.5 kW

Burner Injector

DMS 33

1.8 mm

DMS 51

DMS 33

Pilot Injector

51

30

30

51

A tap is provided on the outlet side of the gas control for a test gauge connection to measure the manifold pressure. To measure inlet pressure, provisions must be made to attach a test gauge to the tap immediately upstream of the gas supply connection to the fireplace.

The fireplace and its individual shut-offvalve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 60 mbar.

If the fireplace must be isolated from the gas supply piping system by closing an individual shut-offvalve, it must be of thehandle-lesstype.

Step 8

Wiring the

Fireplace

Optional Accessories

Optional remote control kits require that 230 VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Wall Switch

NOTE: Electrical wiring must be installed by a competent electrician.

For Standing Pilot Ignition Wiring

Appliance Requirements

WARNING: DO NOT CONNECT 230 VAC

!TO THE GAS CONTROL VALVE OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Position the wall switch in the desired position on a wall. Run a maximum of 780 cm or less length of 0.102 cm diameter minimum wire and connect it to the fireplace ON/OFF switch pigtails.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

31

WARNING: DO NOT CONNECT 230 VAC ! TOTHEWALLSWITCHORTHECONTROL

VALVE WILL BE DESTROYED.

CAUTION

LABEL ALL WIRES PRIOR TO DISCONNECTION

 

WHEN SERVICING CONTROLS. WIRING ERRORS

 

CAN CAUSE IMPROPER AND DANGEROUS OP-

 

ERATION. VERIFY PROPER OPERATION AFTER

 

SERVICING.

OPTIONAL WALL SWITCH

 

 

THERMOSTAT OR REMOTE

 

 

 

 

THERMOCOUPLE

 

 

TP/TH

 

OFF

TP

 

TH

 

 

 

ON

THERMOPILE

 

ON/OFF

REMOTE SWITCH

GAS VALVE

SWITCH

PIGTAIL

 

 

 

Figure 29. Standing Pilot Ignition Wiring Diagram

Step 9

Finishing

Only non-combustiblematerials may be used to cover the black fireplace front.

The following diagram shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 2 , 3 and 4 for other fireplace clearances.

 

 

 

 

 

30,5

 

 

 

 

 

 

 

 

28

 

 

 

NON-COMBUSTIBLE

 

 

 

25,4

 

 

 

 

 

 

23

 

 

 

 

BOARD

 

 

20,3

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

15,2

 

 

 

 

28

 

13

 

 

 

 

 

2325,4

 

10,2

 

 

 

 

1820,3

 

 

7,6

 

 

 

15,2

 

 

5,1

 

 

11,4

 

 

 

9

10,2

13

 

 

 

2,5

8

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP FRONT EDGE

OF FIREPLACE

Note: all dimensions are shown in centimeters.

Figure 30. Minimum Vertical and Maximum Horizontal Dimensions of Combustibles above Fireplace

!WARNING: WHEN FINISHING THE FIREPLACE, NEVER OBSTRUCT OR MODIFY THE AIR INLET/OUTLET GRILLES IN ANY MANNER.

Note: Factory installednon-combustibleboard may only be replaced with HHT product codeSUPERM-60 material and must be fully replaced in its entirety.

32

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

CAUTION

1.Apply only noncombustible facing material to the fireplace surround.

IF JOINTS BETWEEN THE FINISHED WALLS AND THE FIREPLACE SURROUND (TOP AND SIDES) ARE SEALED, A 150ºC. MINIMUM SEALANT MATERIAL MUST BE USED. THESE JOINTS ARE NOT REQUIRED TO BE SEALED. ONLY NONCOMBUSTIBLE MATERIAL (USING 150º C. MINIMUM ADHESIVE, IF NEEDED) CAN BE APPLIED AS FACING TO THE FIREPLACE SURROUND. SEE FIGURE 31.

TOP SEAL

FINISH MATERIAL

MAY BE COMBUSTIBLE

JOINT

- TOP AND SIDES OF UNIT

SIDE SEAL

JOINT

1,3 cm

1,3 cm

Figure 31. Sealant Material

Step 10 Installing Trim, Refractory, Logs, and Ember Material

Installing the Trim

Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall, fireplace top and sides can only be sealed with a 150º C minimum sealant.

Install optional marble and brass trim surround kits as desired. Marble, brass, brick, tile, or other noncombustible materials can be used to cover up the gap between the sheet rock and the fireplace.

Do not obstruct or modify the

! WARNING: CHILDREN AND ADULTS

air inlet/outlet grilles. When

SHOULD BE ALERTED TO THE HAZARDS

OF HIGH TEMPERATURES OF WORKING

overlapping on both sides,

SURFACES ON THESE HEATERS. WORKING

leave enough space so that the

SURFACES INCLUDE ALL GLASS PANELS

bottom grille can be opened

AND DECORATIVE DOORS. YOUNG CHIL-

and the trim door removed.

DREN SHOULD BE CAREFULLY SUPERVISED

 

WHEN THEY ARE IN THE SAME ROOM AS THE

Installing the Ceramic Re-

APPLIANCE.

fractory

 

Remove dress guard, glass door and log package. Remove refractory pieces from packaging (see Figure 32). Position rear refractory piece first and then slide both side pieces through the upper guide openings until they sit firmly against the rear of the unit. See following pages for log installation instruction.

Figure 32.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

33

Log Set Assembly: LOGS-6TRSCE

LOG PLACEMENT

INSTRUCTIONS

 

 

 

 

1

4

2

3 5

Carefully remove the logs from the packaging. CAUTION: Logs are fragile!

1

 

1

 

 

 

LOG #1 (SRV2049-700): Place log #1 at the rear of the unit against the rear grate tabs with the notches on the bottom of the log lining up with the grate bars.

2

2

LOG #2 (SRV2049-701): Locate the bottom grooves of log #2 over the second and third grate bars. Push back against the grate tabs on these bars.

34

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

3

3

 

LOG #3 (SRV385-723): Rest log #3 on the grooves on log #1 and log #2.

4

 

4

 

 

 

 

 

LOG #4 (SRV385-721): Rest log #4 in the groove on log #1 with its front next to the left side of the log grate as shown.

5

 

5

 

 

 

 

 

LOG #5 (SRV385-722): Push log #5 against the grate tabs on the 5th grate bar and rest its top in the groove on log #1.

If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

35

Placing the Ember Material

Two bags of ember material are shipped with this gas fireplace. Use only a portion of each bag for the best appearance and operation.

To place the ember material:

Remove latches and tension springs around the glass door.

Remove the glass door from the unit (Figure 33).

LATCHES

(BOTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

Figure 33. Glass Assembly

Place small pieces of ember material on burner top (Figure 34). Do NOT press embers into burner ports. Cover the top of the burner with a single layer of ember material. Do NOT place embers on the ports as noted in Figure 34.

Figure 34. Placement of the Ember Material

Save the remaining ember materials for use during fireplace servicing.

Replace the glass door and a front trim door on the unit (see Replacement Parts Section of the manual.)

Replace the latches and tension springs.

36

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Step 11

Before Lighting

the Fireplace

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

Keep children away

CAREFULLY SUPERVISE children in same room as fireplace.

Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Before lighting the fireplace, be sure to do the following:

Review safety warnings and cautions

Read the Safety and Warning Informationsection at the beginning of this Installers Guide.

Double-checkfor gas leaks

Before lighting the fireplace, double-checkthe unit for possible gas leaks.

Double-checkflue terminations and front grilles for obstructions.

Before lighting the fireplace, double-checkthe unit for possible obstructions that could be blocking the flue terminations or the front grilles.

Double-checkfor faulty components

Any component that is found to be faulty MUST BE replaced with an approved component. Tampering with the fireplace components isDANGEROUS and voids all warranties.

A small amount of air will be in the gas supply lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and will operate normally.

Subsequent lightings of the fireplace will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

NOTE: The fireplace should be run for 3 to 4 hours on the initialstart-up.Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the fireplace for an additional 8 hours. This will help to cure the products used in the paint and logs.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

37

Step 12

Lighting the

Fireplace

After the

Installation

You’ve reviewed all safety warnings, you’ve checked the fireplace for gas leaks, you know the flue system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the fireplace.

!WARNING: PLEASE REFER TO THE USER’S MANUAL FOR ALL CAUTIONS, SAFETY, AND WARNING INFORMATION PERTAINING TO THE LIGHTING AND OPERATION OF THE FIREPLACE.

LEAVE THIS INSTALLATION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.

38

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Fireplace

Maintenance

IMPORTANT

Although the frequency of your appliance servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance checkup at the beginning of each heating season. See the table below for specific guidelines regarding each fireplace maintenance task.

TURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE.

Type of

 

 

Fireplace Maintenance Task To

Fireplace

Frequency

By

Be Completed

Maintenance

 

 

 

 

 

 

 

 

 

Replacing

Once annually,

Qualified

Brush away loose ember material near

Old Ember

during the annual

Service

the burner. Replace old ember material

Material

checkup

Technician

with 1 cm thin pieces of Glowing Ember

 

 

 

(050-721).New ember material should

 

 

 

be placed on top of the burner. Save the

 

 

 

remaining ember material and repeat this

 

 

 

procedure at your next servicing. For more

 

 

 

information, see Placing Ember Material

 

 

 

in the INSTALLERS GUIDE.

 

 

 

 

Cleaning

Once annually

Qualified

Brush or vacuum the control compartment,

Burner and

 

Service

and burner areas surrounding the logs.

Controls

 

Technician

 

 

 

 

 

Checking

Periodically

Qualified

Make a visual check of your fireplace’s

Flame

 

Service

flame patterns. Make sure the flames are

Patterns,

 

Technician/

steady, not lifting or floating. See the pic-

Flame

 

Owner

ture in Figure 35. The thermopile/thermo-

Height

 

 

couple tips should be covered with flame.

 

 

 

See picture in Figure 36.

 

 

 

 

Checking

Before initial use

Qualified

Inspect the external terminal cap on a

Flue System

and at least an-

Service

regular basis to ensure that no debris is

 

nually thereafter,

Technician/

interfering with the flow of air, Inspect en-

 

more frequently if

Owner

tire flue system for proper function.

 

possible

 

 

 

 

 

 

Cleaning

After the first 3-4

Qualified

Remove and clean glass after the first 3

Glass Door

hours of use. As

Service

to 4 hours of use. After the initial cleaning,

 

necessary after

Technician

clean as necessary, particularly after adding

 

initial cleaning.

 

new ember material. Film deposits on the

 

 

 

inside of the glass door should be cleaned

 

 

 

off using a household glass cleaner. NOTE:

 

 

 

DO NOT handle or attempt to clean the door

 

 

 

when it is hot and DO NOT use abrasive

 

 

 

cleaners.

 

 

 

 

4

Maintaining

and Servicing

Your Fireplace

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

39

MAKE SURE THE FLAMES

ARE STEADY—NOT

LIFTING OR FLOATING.

Figure 35. Burner Flame Patterns

STANDING PILOT

Figure 36. Pilot Flame Patterns

40

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Standing Pilot Troubleshooting

Symptom

Possible Cause

Corrective Action

 

 

 

1. After repeated

a. Defective ignitor

Check the spark at the electrode and pilot.

triggering of

 

If no spark and electrode wire is properly

the red or black

 

connected, replace the ignitor.

piezo button, the

b. Defective pilot or

Using a match, light the pilot. If the pilot

spark ignitor will

misaligned electrode

lights, turn off the pilot and trigger the red

not light the pilot.

(spark at electrode)

or black piezo button again. If the pilot

 

 

lights, an improper gas/air mixture caused

 

 

the bad lighting and a longer purge period

 

 

is recommended. If the pilot will not light,

 

 

ensure that the gap at the electrode and

 

 

pilot is 0.3 cm to have a strong spark. If the

 

 

gap is OK, replace the pilot.

 

c. No gas or low gas

Check the remote shut-offvalves from the

 

pressure

fireplace. Usually, there is a valve near the

 

 

gas main. There can be more than one (1)

 

 

valve between the fireplace and the main.

 

d. No LP in the tank

Check the LP (propane) tank. You may be

 

 

out of fuel.

2. The pilot will

a. Defective thermocouple

Check that the pilot flame impinges on the

not stay lit

 

thermocouple. Clean and/or adjust the pilot

after carefully

 

for maximum flame impingement.

following

 

Ensure that the thermocouple connection

the lighting

 

at the gas valve is fully inserted and tight

instructions.

 

(hand tighten plus 1/4 turn).

 

 

Disconnect the thermocouple from the

 

 

valve, place one millivolt meter lead wire

 

 

on the tip of the thermocouple and the

 

 

other meter lead wire on the thermocouple

 

 

copper lead. Start the pilot and hold the

 

 

valve knob in. If the millivolt reading is less

 

 

than 15mV, replace the thermocouple.

 

b. Defective valve

If thermocouple is producing more than 15

 

 

millivolts, replace faulty valve.

3. The pilot is

a. ON/OFF switch or wires

Check the ON/OFF switch and wires for

burning, there is

defective

proper connections. Place the jumper wires

no gas burner,

 

across the terminals at the switch. If the

the valve knob

 

burner comes on, replace the defective

is in the ON

 

switch. If the switch is OK, place the jumper

position, and the

 

wires across the switch wires at the gas

ON/OFF switch

 

valve. If the burner comes on, the wires are

is in the ON

 

faulty or connections are bad.

position.

b. Thermopile may not be

If the pilot flame is not close enough

 

generating sufficient

physically to the thermopile, adjust the

 

millivoltage

pilot flame.

 

 

Be sure the wire connections from the

 

 

thermopile at the gas valve terminals are

 

 

tight and that the thermopile is fully inserted

 

 

into the pilot bracket.

5

Troubleshooting

With proper installation, operation, and maintenance your gas fireplace will provide years of trouble-freeservice. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

41

Symptom

Possible Cause

Corrective Action

 

 

 

3. (Continued)

b. Thermopile may not be

Check the thermopile with a millivolt meter.

 

generating sufficient

Take the reading at TH-TP&TPterminals

 

millivoltage

of the gas valve. The meter should read

 

 

325 millivolts minimum, while holding the

 

 

valve knob depressed in the pilot position,

 

 

with the pilot lit, and the ON/OFF switch

 

 

in the OFF position. Replace the faulty

 

 

thermopile if the reading is below the

 

 

specified minimum.

 

 

With the pilot in the ON position, disconnect

 

 

the thermopile leads from the valve. Take

 

 

a reading at the thermopile leads. The

 

 

reading should be 325 millivolts minimum.

 

 

Replace the thermopile if the reading is

 

 

below the minimum.

 

 

 

 

c. Defective valve

Turn the valve knob to the ON position.

 

 

Place the ON/OFF switch in the ON

 

 

position. Check the millivolt meter at the

 

 

thermopile terminals. The millivolt meter

 

 

should read greater than 125mV If the

 

 

reading is acceptable, and if the burner

 

 

does not come on, replace the gas valve.

 

 

 

 

d. Plugged burner orifice

Check the burner orifice for stoppage.

 

 

Remove stoppage.

 

 

 

 

e. Wall switch or wires are

Follow the corrective action in Symptom

 

defective

and Possible Cause 1. a. above. Check

 

 

the switch and wiring. Replace where

 

 

defective.

 

 

 

4. Frequent pilot

a. Pilot flame may be too

Clean and adjust the pilot flame for maximum

outage problem.

high or too low, or blowing

flame impingement on thermocouple.

 

(high), causing pilot safety

Follow lighting instructions carefully.

 

to drop out

 

 

 

 

42

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

Symptom

Possible Cause

Corrective Action

 

 

 

5. The pilot and

a. No LP in the tank

Check the LP (propane) tank. Refill the

main burner

 

fuel tank.

extinguish while

 

 

b. Inner flue pipe leaking

Check for gas leaks.

in operation.

 

exhaust gases back into

 

 

the system

 

 

 

 

 

c. Horizontal flue improperly

The horizontal flue cap should slope down

 

pitched

only enough to prevent any water from

 

 

entering the unit. The maximum downward

 

 

slope is 0.6 cm.

 

 

 

 

d. Glass too loose and

Tighten the corner.

 

air tight packet leaks in

 

 

corners after usage

 

 

 

 

 

e. Bad thermopile or

Replace if necessary.

 

thermocouple

 

 

 

 

 

f. Improper flue cap

Check for proper installation and freedom

 

installation

from debris or blockage.

 

 

 

6. Glass soots.

a. Flame impingement

Adjust the log set so that the flame does

 

 

not excessively impinge on it.

 

 

 

 

b. Improper venturi setting

Adjust the air shutter at the base of the

 

 

burner.

 

 

 

 

c. Debris around venturi

Inspect the opening at the base of the

 

 

burner. NO MATERIAL SHOULD BE

 

 

PLACED IN THIS OPENING.

 

 

 

7. Flame burns

a. Insufficient oxygen being

Ensure that the flue cap is installed properly

blue and lifts off

supplied

and free of debris. Ensure that the flue

burner.

 

system joints are tight and have no leaks.

 

 

Ensure that no debris has been placed in

 

 

the area at the base of, or in the area of,

 

 

the air holes in the center of the base pan

 

 

beneath the burner.

 

 

Ensure that the glass is tightened properly

 

 

on the unit, particularly on top corners.

 

 

 

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

43

Limited Lifetime Warranty

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

 

Warranty Period

 

HHT Manufactured Appliances and Venting

 

 

 

 

Parts

Labor

Gas

Wood

Pellet

EPA

Coal

Electric

Venting

Components Covered

 

 

Wood

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All parts and material except as

 

 

1 Year

X

X

X

X

X

X

X

covered by Conditions,

 

 

Exclusions, and Limitations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

listed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

X

X

 

 

Igniters, electronic components,

 

 

2 years

 

 

 

 

and glass

 

 

 

 

 

 

 

 

 

 

 

X

X

X

X

X

 

 

Factory-installedblowers

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

Molded refractory panels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 years

 

 

X

 

 

 

 

Firepots and burnpots

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 years

1 year

 

 

X

X

 

 

 

Castings and baffles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7 years

3 years

 

X

X

X

 

 

 

Manifold tubes,

 

 

 

 

 

 

HHT chimney and termination

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

1 year

X

 

 

 

 

 

 

Burners, logs and refractory

 

 

years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited

3 years

X

X

X

X

X

 

 

Firebox and heat exchanger

 

 

Lifetime

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90 Days

X

X

X

X

X

X

X

All replacement parts

 

 

beyond warranty period

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See conditions, exclusions, and limitations on next page.

4021-645C12-29-10

 

 

 

 

 

 

 

Page 1 of 2

44

 

 

 

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

 

 

WARRANTY CONDITIONS:

This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites.

This warranty is only valid while the HHT appliance remains at the site of original installation.

Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the product.

Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this warranty.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur. This is not a flaw and is not covered under warranty.

Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discoloration of glass.

Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.

Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/ incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed constructions, insufficient make-upair supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the appliance.

Non-HHTventing components, hearth components or other accessories used in conjunction with the appliance.

Any part of a pre-existingfireplace system in which an insert or a decorative gas appliance is installed.

HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of the structure.

This warranty is void if:

The appliance has been over-firedor operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals.Over-firingcan be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes.

The appliance is subjected to prolonged periods of dampness or condensation.

There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE.

4021-645C12-29-10

Page 2 of 2

Heat & Glo • 6000TRS-CE2049-900Rev. Q • 2/11

45