Heat & Glo LifeStyle 6000ARCH User Manual

Size:
1.69 Mb
Download

Heat-N-Glo

Models:

6000TR 6000XLT-CDN6000ARCH 6000XLS

Installers Guide

Underwriters

Laboratories Listed

WARNING: IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

-What to do if you smell gas

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

-Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

Printed in U.S.A. Copyright 2000,

Heat-N-Glo,a division of Hearth Technologies Inc. 20802 Kensington Boulevard, Lakeville, Mn 55044

READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS INSTALLERS GUIDE MUST BE LEFT WITH THE APPLIANCE FOR FUTURE REFERENCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, SERVICE AGENCY, OR THE GAS SUPPLIER.

1.This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where not prohibited by local codes.

2.This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

Please contact your Heat-N-Glodealer for any questions or concerns. For the number of your nearestHeat-N-Glodealer, please call612-985-6000.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792;1 4,520,791; 4,793,322; 4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia) 543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico)97-0457;(New Zealand) 200265; or other U.S. and foreign patents pending.

525-983C1/00

SAFETY AND WARNING INFORMATION

!READ andUNDERSTAND all instructions carefully before starting the installation.FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty.

Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the

!Owners Guide.

DO NOT USE this appliance if any part has been under water. ImmediatelyCALL a

!qualified service technician to inspect the unit and to replace any part of the control system and any gas control which has been under water.

!THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a qualified service person. The

!appliance and venting system should be INSPECTED before initial use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It isIMPERATIVE that the unit’s control compartment, burners, and circulating air passagewaysBE KEPT CLEAN to provide for adequate combustion and ventilation air.

!Always KEEP the appliance clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the

!appliance CLEAR of all obstacles and materials for servicing and proper operations. Due to the high temperature, the appliance should beLOCATED out of traffic areas

!and away from furniture and draperies. Clothing or flammable material SHOULD NOT BE PLACED on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature

!and should STAY AWAY to avoid burns or clothing ignition. Young children should beCAREFULLY SUPERVISED when they are in the same room as the appliance.

!These units MUST use one of the vent systems described in the Installing the Fireplace section of theInstallers Guide.NO OTHER vent systems or componentsMAY BE USED.

!This gas fireplace and vent assembly MUST be vented directly to the outside andMUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas applianceMUST USE a separate vent system. Common vent systems arePROHIBITED.

!INSPECT the external vent cap on a regular basis to make sure that no debris is interfering with the air flow.

!The glass door assembly MUST be in place and sealed, and the trim door assemblyMUST be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door removed, cracked, or broken.

!Replacement of the glass door should be performed by a licensed or qualified service person. DO NOT strike or slam the glass door.

!The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied by the gas fireplace manufacturer.NO SUBSTITUTE material may be used.

!DO NOT USE abrasive cleaners on the glass door assembly.DO NOT ATTEMPT to clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

!service technician perform an appliance check-upat the beginning of each heating season.

Any safety screen or guard removed for servicing must be replaced before operating

!this appliance.

2

Safety and Warning Information .........................

2

Section 1: Approvals and Codes ......................

4

Approval Listings and Codes ...................................

4

Appliance Certification .............................................

4

Installation Codes ....................................................

4

HighAltitude Installations..........................................

4

Section 2: Getting Started ................................

5

Introducing the Heat-N-GloGas Fireplaces ..............

5

Pre-installationPreparation......................................

5

Section 3: Installing the Fireplace ....................

8

Step 1

Locating the Fireplace ...............................

8

Step 2

Framing the Fireplace ...............................

9

Step 3

Installing the Vent System ........................

10

 

A. Vent System Approvals ........................

10

 

B. Installing Vent Components .................

20

 

C. Vent Termination .................................

26

Step 4

Positioning, Leveling, and

 

 

Securing the Fireplace .............................

31

Step 5

The Gas Control Systems .......................

31

Step 6

The Gas Supply Line ...............................

32

Step 7

Gas Pressure Requirements ...................

33

Step 8

Wiring the Fireplace ................................

34

Step 9

Finishing .................................................

36

Step 10

Installing Trim, Logs, and

 

 

Ember Material ........................................

37

 

Installing the Trim.....................................

37

 

Positioning the Logs ................................

38

 

Placing the Ember Material ......................

38

Step 11 Before Lighting the Fireplace....................

40

Step 12 Lighting the Fireplace ...............................

40

Step 13 Heating Control - 6000XLT-CDN ..............

41

Step 14

Relief Ports - 6000ARCH .........................

41

After the Installation ...............................................

41

Section 4: Maintenance and Servicing ..........

42

Section 5: Replacement Parts

 

and Accessories .................................................

44

Replacement Parts ...............................................

44

Accessories .........................................................

48

TABLE

OF

CONTENTS

3

1

Approvals

and Codes

4

Approval Listings

Appliance Certification

and Codes

The Heat-N-Glomodels discussed in thisInstallers

 

 

Guide have been tested to certification standards

 

 

and listed by the applicable laboratories.

 

 

 

 

 

 

 

 

 

CERTIFICATION

MODEL

LABORATORY

TYPE

STANDARD

6000TR &

Underwriters

 

Vented Gas

ANSI Z21.50• CGA2.22/IR#41

6000ARCH

Laboratories

 

Fireplace

 

6000XLT-CDN

Underwriters

 

Vented Gas Fireplace

ANSI Z21.50• CGA2.22

 

Laboratories

 

& Vented Gas

ANSI Z21.88• CSA2.33

 

 

 

Fireplace Heater

 

 

 

 

 

 

6000XLS

Underwriters

 

Vented Gas

ANSI Z21.88• CSA2.33

 

 

 

Fireplace Heater

 

 

 

 

 

 

Installation Codes

The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you are in compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGAB149 Installation Codes (in Canada). The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes with the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the CSA C22.1 Canadian Electric Code (in Canada).

These models may be installed in a bedroom or bed-sittingroom in the U.S.A. and Canada.

High Altitude Installations

U.L. Listed gas fireplaces are tested and approved for elevations from 0 to 2,000 feet in the U.S.A. and from 0 to 4,500 feet in Canada.

When installing this fireplace at an elevation above 2,000 feet (in the United States), it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input should be reduced four percent (4%) for each 1,000 feet above sea level, unless the heating value of the gas has been reduced, in which case this general rule will not apply. To identify the proper orifice size, check with the local gas utility.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for your location.

Introducing the

Heat-N-Glo

Gas Fireplaces

Pre-install

Preparation

Heat-N-Glodirect vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems.

Gas fireplace diagrams, including the dimensions, are shown in this section.

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass.Do not install any unit with damaged, incomplete, or substitute parts.

NOTE: FOR MODEL 6000TR ONLY:

These fireplaces are shipped from the factory with a BTU rating of 27,000 BTU’s. The fireplace can be installed with the vent pipe coming off the top of the unit or the rear of the unit. If you install the unit with the vent pipe coming off the top of the unit, you may run the unit at 31,000 BTU (NG) (30,000 BTU LP), replace the burner orifice with the orifice included in the manual bag. DO NOT REPLACE THE ORIFICE

IF YOU ARE USING THE REAR SET OF VENT COLLARS.

Changing the orifice when venting out the top.

1.Remove the glass door.

2.Using a 1/4” socket, remove the sheetmetal screws holding the long refractory clip in place. Remove the logs and refractory as one piece.

3.Remove the protective plastic from the logs.

4.Remove the two sheetmetal screws holding the burner and remove the burner.

5.Replace the burner orifice with the orifice included in the plastic manual bag (#36DMS for natural gas or #51DMS for propane). Be careful to hold the brass elbow so you don’t kink the aluminum tube.

6.Reverse the steps to replace the burner, logs, refractory, and clip.

The vent system components and trim doors are shipped in separate packages. The gas logs may be packaged separately and must be field installed.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and

may present a fire hazard.

2

Getting

Started

5

The Heat-N-GloWarranty will be voided by, andHeat-N-Glodisclaims any responsibility for, the following actions:

Installation of any damaged fireplace or vent system component.

Modification of the fireplace or direct vent system.

Installation other than as instructed by Heat-N-Glo.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not manufactured and approved by Heat-N-Glo,not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, it’s necessary to determine:

Where the unit is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devicessuch as a fan, wall switch, or remotecontrol—aredesired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

NOTE:

6000TR has top and rear collars. 6000XLT-CDNhas top collars only. 6000XLS has rear collars only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Left Side

 

 

 

 

 

 

 

 

Front

Right Side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

Figure 1. Diagram of the 6000TR, 6000XLT-CDNand 6000XLS

Figure 2. Diagram of the 6000ARCH

7

3

Installing the

Fireplace

8

Step 1

Locating the

Fireplace

The diagram below shows space and clearance requirements for locating a fireplace within a room.

MODEL

A

B

C

D

E

6000TR &

42

22

37 1/8

52 1/2

74 1/4

6000XLS

 

 

 

 

 

6000XLT-CDN

42

22

35 1/4

49 3/4

70 3/8

6000ARCH

42*

22

35 1/4

49 3/4

70 3/8

481/4**

* SURROUND IN FRONT OF FINISHED WALL

**SURROUND FLUSH WITH FINISHED WALL. NOTE: DIMENSIONS SHOWN IN INCHES.

Figure 3. Fireplace Dimensions, Locations, and

Space Requirements

Clearance Requirements

The top, back, and sides of the fireplace are defined by stand-offs.

Minimum Clearances from the Fireplace to

Combustible Materials

Glass

 

Rear of

Sides of

Top of

 

Front

Floor

Fireplace

Fireplace

Fireplace

Ceiling

 

 

 

 

 

 

36 inches

0

1/2 inch

1/2 inch

3-1/2inches

31 inches

(914 mm)

 

(13 mm)

(13 mm)

(89 mm)

(787 mm)

 

 

 

 

 

 

The minimum clearance to a perpendicular wall extending past the face of the fireplace is one inch (25 mm).

The back of the fireplace may be recessed 21 1/2 inches (546 mm) into combustible construction.

 

 

Minimum Clearances from the Vent Pipe to

 

 

 

 

 

Combustible Materials

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For Vertical

 

 

 

 

For Horizontal Sections

Sections

At Wall Firestops

 

 

 

 

 

 

 

 

 

Top

 

Bottom

Sides

 

Top

Bottom

Sides

 

 

 

 

 

 

 

 

 

3 inches

 

1 inch

1 inch

1 inch

2-1/2inches

1/2 inch

1 inch

(75 mm)

 

(25 mm)

(25 mm)

(25 mm)

(63.7 mm)

(13 mm)

(25 mm)

 

 

 

 

 

 

 

 

 

 

 

 

For minimum clearances, see the direct vent

 

 

 

termination clearance diagrams on pages 28 and 30 in

 

 

 

this manual.

 

 

 

 

Step 2

 

Fireplace framing can be built before or after the

Framing the

fireplace is set in place. Framing should be positioned

Fireplace

to accommodate wall coverings and fireplace facing

material. The diagram below shows framing reference

 

 

 

 

 

 

dimensions.

 

 

 

 

CAUTION

 

MEASURE FIREPLACE DIMENSIONS, AND

 

 

 

VERIFY FRAMING METHODS AND WALL

 

 

 

COVERING DETAILS, BEFORE FRAMING

 

 

 

CONSTRUCTION BEGINS.

 

 

 

SHOWS CENTER OF12" X 12"

VENT FRAMING HOLES FOR

TOP & REAR VENTING.

 

 

 

 

B

 

 

 

 

 

 

C

 

 

Framing should be

A

 

 

 

 

 

E D

 

constructed of 2 X 4

 

 

 

 

lumber or heavier.

 

 

Model

A

B

C

D

E

6000TR

42

38 1/4

22

42

26 1/4

6000XLS

42

38 1/4

22

N/A

26 1/4

6000XLT-CDN

42

38 1/4

22

42

N/A

6000ARCH

42*

41 7/8

22

53 5/8

N/A

 

48 1/4**

 

 

 

* SURROUND IN FRONT OF FINISHED WALL

 

 

 

** SURROUND FLUSH WITH FINISHED WALL

 

 

 

NOTE: DIMENSIONS SHOWN IN INCHES

 

 

 

Figure 4. Framing Dimensions

 

 

 

9

 

 

 

 

 

Step 3

A. Vent System Approvals

 

Installing the

These models are approved to use D-seriesdirect vent

 

Vent System

pipe components and terminations. Approved vent

 

 

system components are labeled for identification. NO

 

 

OTHER VENTING SYSTEMS OR COMPONENTS

 

 

MAY BE USED. Detailed installation instructions are

 

 

included with each vent termination kit and should be

 

 

used in conjunction with this Installers Guide. The

 

 

drawing below shows vent system components and

 

 

terminations.

 

 

The flame and ember appearance may vary based on the

 

 

type of fuel burned and the venting configuration used.

 

 

Identifying Vent Components

 

 

The vent systems installed on this gas fireplace may

 

 

include one, two, or three 90° elbow assemblies. The

 

 

relationships of vertical rise to horizontal run in vent

 

 

configurations using 90° elbows MUST BE strictly

 

 

adhered to. The rise to run relationships are shown in

 

 

the venting drawings and tables. Refer to the diagrams

 

 

on the next several pages.

 

 

NOTE: TWO 45° ELBOWS MAY BE USED IN PLACE

 

 

OF ONE 90° ELBOW. RISE TO RUN RATIOS IN THE

 

 

VENT SYSTEM MUST BE FOLLOWED IF 45°

 

 

ELBOWS ARE USED.

 

 

This model has vent starting collars on both the top and

 

 

the back of the unit. Depending upon the installation,

 

 

decide which ONE set of starting collars will be used to

 

 

attach the vent system. The starting collar sealing cap

 

 

must remain on the starting collar NOT used.

 

 

VENT SYSTEM COMPONENTS

 

VENT SYSTEM

 

 

TERMINATION KITS

 

10

Figure 5. Vent Components and Terminations