Harman-Kardon AVR 2650, AVR 265, AVR 365, AVR 3650 User Manual

0 (0)

AVR 3650,AVR 365 AVR 2650,AVR 265

Audio/video receiver

ENGLISH

Owner’s Manual

AVR

Introduction	3
Supplied Accessories	3
Important Safety Information	3
Place the Receiver	3
Front-Panel Controls	4
Rear-Panel Connectors	6
System Remote Control Functions	8
Zone 2 Remote Control Functions
(AVR 3650/AVR 365 only)	10
Introduction to Home Theater	12
Typical Home Theater System	12
Multichannel Audio	12
Surround Modes	12
Place Your Speakers	13
Placing the Left, Center and Right Speakers	13
Placing the Surround Speakers in a
5.1-Channel System	13
Placing the Surround Speakers in a
7.1-Channel System	13
Placing Front Height Speakers in a
7.1-Channel System	13
Placing the Subwoofer	13
Types of Home Theater System Connections	14
Speaker Connections	14
Subwoofer Connections	14
Source Device Connections	14
Video Connections	15
Radio Connections	16
Network Connector	16
USB Port	16
RS-232 Connector	16
Making Connections	17
Connect Your Speakers	17
Connect Your Subwoofer	17
Connect Your TV or Video Display	17
Connect Your Audio and Video Source Devices	18
Connect The Bridge IIIP	20
Connect to Your Home Network	20
Connect the Radio Antennas	20
Install a Multizone System	21
Connect IR Equipment (AVR 3650/AVR 365 only)	22
Connect the 12V Trigger Output	23
Connect to AC Power	23

Table of Contents

Set Up the Remote Control	23
Install the Batteries in the Remote Control	23
Program the Remote to Control
Your Source Devices and TV	23
Set Up the AVR	25
Turn On the AVR	25
Using the On-Screen Menu System	25
Configure the AVR for Your Speakers	25
Set Up Your Sources	26
Set Up the Network	27
Operating Your AVR	28
Controlling the Volume	28
Muting the Sound	28
Dolby® Volume	28
Listening Through Headphones	28
Selecting a Source	28
Listening to FM and AM Radio	29
Listening to SIRIUS® Satellite Radio	29
Listening to Media on a USB Device
(AVR 3650/AVR 365)	30
Listening to an iPod/iPhone Device	30
Listening to Internet Radio	31
Listening to Media via Your Home Network	32
Selecting a Surround Mode	32
Audio Effects	32
Video Modes	32
Advanced Functions	33
Audio Processing and Surround Sound	33
Video Processing	34
Manual Speaker Setup	36
Listening in Zone 2	39
System Settings	39
Settings Lock	40
Advanced Remote Control Programming	41
Recording	41
Sleep Timer	41
Resetting the Remote	42
Processor Reset	42
TROUBLESHOOTING	43
Specifications	44
Appendix	45

AVR

Introduction, Supplied Accessories,

Important Safety Information and Place the Receiver

Introduction

Thank you for choosing this Harman Kardon product!

For more than fifty years,the Harman Kardon mission has been to share a passion for music and entertainment, using leading-edge technology to achieve premium performance. Sidney Harman and Bernard Kardon invented the receiver, a single component designed to simplify home entertainment without compromising performance. Over the years, Harman Kardon products have become easier to use, while offering more features and sounding better than ever.

The AVR 3650, AVR 2650, AVR 365 and AVR 265 7.1-channel digital audio/video receivers continue this tradition with some of the most advanced audio and video processing capabilities yet, and a wealth of listening and viewing options.

To obtain the maximum enjoyment from your new receiver, please read this manual and refer back to it as you become more familiar with its features and their operation.

If you have any questions about this product, its installation or its operation, please contact your Harman Kardon retailer or custom installer, or visit the Web site at www.harmankardon.com.

Supplied Accessories

The following accessory items are supplied with your receiver. If any of these items are missing, please contact your Harman Kardon dealer or Harman Kardon customer service at www.harmankardon.com.

•• System remote control

•• Zone 2 remote control (AVR 3650/AVR 365 only)

•• EzSet/EQ™ microphone

•• AM loop antenna

•• FM wire antenna

•• Six AAA batteries (AVR 3650/AVR 365); four AAA batteries (AVR 2650/AVR 265)

•• AC power cord

IMPORTANT SAFETY INFORMATION

Verify Line Voltage Before Use

The AVR 3650 and AVR 2650 have been designed for use with 120-volt AC current. The AVR 365 and AVR 265 have been designed for use with 220 – 240-volt AC current. Connection to a line voltage other than that for which your receiver is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord supplied with your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use your receiver for any considerable length of time, disconnect the plug from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your warranty. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.

CATV or Antenna Grounding (AVR 3650/AVR 2650)

If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the United States National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (cable TV) system installer’s attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

Place the Receiver

•• Place the receiver on a firm and level surface. Be certain that the surface and any mounting hardware can support the AVR’s weight.

•• Provide proper space above and below the receiver for ventilation. If you install the receiver in a cabinet or other enclosed area, provide cooling air within the cabinet. Under some circumstances, a fan may be required.

•• Do not obstruct the ventilation slots on the top of the receiver or place objects directly over them.

•• Do not place the receiver directly on a carpeted surface.

•• Do not place the receiver in moist or humid locations, in extremely hot or cold locations, in areas near heaters or heat registers, or in direct sunlight.

ENGLISH

AVR

Front-Panel Controls

	power	Info
	button	button
power	Setup	Ir	message	up/down	volume
Indicator	button	Sensor	display	buttons	knob


uSb		resolution	video	back/exit	ok	Source list
port		button	modes	button	button	button
			button
	hdmI® front		Audio	Surround	left/right	headphone Jack/
	Input connector		effects	modes	buttons	ezSet/eq
			button	button		mic Input

Continued on next page

AVR

Front-Panel Controls, continued

Power Indicator: this led has three possible modes:

•led is off: Indicates that the Avr is unplugged or the rear-panel main power switch is off.

•led glows amber: Indicates that the Avr is in the Standby mode.

•led glows white: Indicates that the Avr is turned on.

IMPORTANT NOTE: If the protect message ever appears on the Avr’s frontpanel message display, turn off the Avr and unplug it from the Ac outlet. check all speaker wires for a possible short-circuit (the “+” and “–” conductors touching each other or both touching the same piece of metal). If a short-circuit is not found, bring the unit to an authorized harman kardon service center for inspection and repair before using it again.

Power button: press this button to turn the receiver on or to place it in the Standby mode.

Setup button: press this button to access the Avr’s main menu.

Info button: press this button to access the Avr’s Source submenu, which contains the settings for the source currently playing. use the up/down buttons to scroll through the different settings.

Message display: various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. when the on-screen display menu system (oSd) is in use, the current menu settings appear.

IR sensor: this sensor receives infrared (Ir) commands from the remote control. It is important to ensure that the sensor is not blocked. AVR 3650/AVR 365 only: If covering the Ir sensor is unavoidable (such as when the receiver is installed inside of a cabinet), connect an optional infrared receiver to the remote Ir In connector on the Avr’s rear panel.

Up/Down buttons: use these buttons to navigate the Avr’s menus. Volume knob: turn this knob to raise or lower the volume.

USB port: you can use this port to perform software upgrades that may be offered in the future. do not connect a storage device, peripheral product or a pc here, unless you are instructed to do so as part of an upgrade procedure.

HDMI (High-Definition Multimedia Interface®) Front Input connector: connect an hdmI-capable source component that will be used only temporarily, such as a camcorder or game console, here.

Resolution button: press this button to access the Avr’s video output resolution setting: 480i, 480p, 720p, 1080i, 1080p or 1080p/24hz. use the up/down and ok buttons to change the setting.

IMPORTANT NOTE: If you set the Avr’s video output resolution higher than the capabilities of the actual connection between the Avr and your tv or video display, you will not see a picture. If you are using the composite video connection from the Avr to your tv (see connect your tv or video display, on page 17), press the resolution button and use the up/down and ok buttons to change the resolution to 480i.

Audio Effects button: press this button to access the Audio effects submenu, which allows you to adjust the Avr’s tone controls and other audio controls. See Set up your Sources, on page 26, for more information.

Video Modes button: press this button for direct access to the video modes submenu, which contains settings you can use to improve the video picture. use the ok button to scroll through the different modes, and use the up/down and left/ right buttons to make adjustments within each mode. See Set up your Sources, on page 26, for more information.

Surround Modes button: press this button to select a listening mode. the Surround modes menu will appear on screen, and the menu line will appear in the front-panel display. use the up/down buttons to change the surround-mode category and the left/right buttons to change the surround mode for that category. See Set up your Sources, on page 26, for more information.

Back/Exit button: press this button to return to the previous menu or to exit the menu system.

Left/Right buttons: use these buttons to navigate the Avr’s menus. OK button: press this button to select the currently highlighted item.

Headphone jack/EzSet/EQ Mic input: connect a 1/4" stereo headphone plug to this jack for private listening. this jack is also used to connect the supplied microphone for the ezSet/eq procedure described in configure the Avr for your Speakers, on page 25.

Source List button: press this button to select a source device to watch/listen to. use the up/down buttons to scroll through the source-device list, and press the ok button to select the source being displayed.

ENGLISH

Harman-Kardon AVR 2650, AVR 265, AVR 365, AVR 3650 User Manual

AVR

Rear-Panel Connectors

composite

SIrIuS® tuner

video Input

video monitor

connector

connectors

out connector

(Avr 3650/Avr 2650)

Analog

digital Audio

composite

12v

record out

video record

trigger

Input connectors

connector

out connector

connector

hdmI

composite

Zone 2 Ir In

the bridge IIIp

monitor out

hdmI Input

video Input

connector

connectors

(Avr 3650/Avr 365)

radio Antenna	Subwoofer	optical	Speaker	network	Ac Input	Ir remote
connectors	connector	digital output	connectors	connector	connector	In/out connectors
		connector				(Avr 3650/Avr 365)

Zone 2 out	Analog Audio	main power	rS-232	fan
connector	Input connectors	Switch	connector	vents
		Rear-Panel Connectors (AVR 3650 shown)

Analog Record Out connector: connect this analog audio output to the analog audio input of a recording device. A signal is available at this output whenever an analog audio source is playing.

HDMI Monitor Out connector: If your tv has an hdmI connector, use an hdmI cable (not included) to connect it to the Avr’s hdmI monitor out connector. the Avr will automatically transcode component and composite video input signals to the hdmI format (upscaling to as high as 1080p), so you do not need to make any other connections to your tv from the Avr or from any of your video source devices.

Notes on using the HDMI Monitor Out connector:

•when connecting a dvI-equipped display to the hdmI monitor out connector, use an hdmI-to-dvI adapter and make a separate audio connection.

•make sure the hdmI-equipped display is hdcp (high-bandwidth digital content protection)-compliant. If it isn’t, do not connect it via an hdmI connection; use an analog video connection instead and make a separate audio connection.

HDMI Input connectors: An hdmI connection transmits digital audio and video signals between devices. If your source devices have hdmI connectors, using them will provide the best possible video and audio performance quality. Since the hdmI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via the hdmI connection. See connect your Audio and video Source devices, on page 18, for more information.

Composite Video Input connectors: use composite video connectors for video source devices that don’t have hdmI or component video connectors. you will also need to make an audio connection from the source device to the Avr. See connect your Audio and video Source devices, on page 18, for more information.

Digital Audio Input connectors: If your non-hdmI source devices have digital outputs, connect them to the Avr’s digital audio connectors. note: make only one type of digital connection (hdmI, optical or coaxial) from each device. See connect your Audio and video Source devices, on page 18, for more information.

Continued on next page

AVR

Rear-Panel Connectors, continued

Composite Video Monitor Out connector: If your tv or video display does not have an hdmI connector, use a composite video cable (not included) to connect the Avr’s composite video monitor out connector to your tv’s composite video input. NOTE: the hdmI connection to your tv is preferred. If you use the composite video connection to your tv, you will not be able to view the Avr’s on-screen menus.

Composite Video Record Out connector: connect an analog video recorder’s video input connector to the Avr’s composite video rec out connector. you can record any composite video input signal. NOTE: to record the audio and video from the source device, connect the Avr’s Analog record output connectors to the analog video recorder’s audio inputs.

Component Video Input connectors: If any of your video source devices have component video connectors (and do not have hdmI connectors), using the component video connectors will provide superior video performance. you will also need to make an audio connection from the device to the receiver. See connect your Audio and video Source devices, on page 18, for more information.

SIRIUS® Tuner connector: connect a SIrIuSconnect™ satellite radio tuner module here. (not included. Available at www.sirius.com.) See connect your Audio and video Source devices, on page 18, for more information.

12V Trigger connector: this connector provides 12v dc whenever the Avr is on. It can be used to turn on and off other devices such as a powered subwoofer.

Zone 2 IR Input connector (AVR 3650/AVR 365 only): connect a remote Ir receiver located in Zone 2 of a multizone system to this jack to control the Avr (and any source devices connected to the remote Ir output connector) from the remote zone.

The Bridge IIIP connector: connect an optional harman kardon the bridge IIIp docking station to this input. Insert the plug until it snaps into place in the connector. IMPORTANT: connect the bridge IIIp only with the Avr’s power turned off.

Radio Antenna connectors: connect the included Am and fm antennas to their respective terminals for radio reception.

Zone 2 Out connectors: connect these jacks to an external amplifier to power the speakers in the remote zone of a multizone system.

Subwoofer connector: connect this jack to a powered subwoofer with a line-level input. See connect your Subwoofer, on page 17, for more information.

Analog Audio Input connectors: use the Avr’s Analog Audio Input connectors for source devices that don’t have hdmI or digital audio connectors. See connect your Audio and video Source devices, on page 18, for more information.

Optical Digital Output connector: connect a digital audio recorder’s optical digital input to the Avr’s optical digital output connector. you can record both coaxial and optical digital audio signals.

Speaker connectors: use two-conductor speaker wire to connect each set of terminals to the correct speaker. See connect your Speakers, on page 17, for more information.

NOTE: the speaker connectors, also called Assigned Amp speaker connectorsare used for the surround back channels in a 7.1- channel home theater, or you can reassign them to a remote room for multizone operation or to front height channels for dolby pro logic® IIz operation. See place your Speakers, on page 13, for more information.

Network connector: use a cat. 5 or cat. 5e cable (not supplied) to connect the Avr’s network connector to your home network to enjoy Internet radio and content from dlnA®-compatible devices that are connected to the network. See connect to your home network, on page 20, for more information.

Main Power switch: this mechanical switch turns the Avr’s power supply on or off. It is usually left on, and it cannot be turned on or off using the remote control.

AC Input connector: After you have made all other connections, plug the supplied Ac power cord into this receptacle and into an unswitched wall outlet.

RS-232 connector: this connector is used to connect to external control hardware. consult a certified professional installer for more information.

IR Remote In/Out connectors (AVR 3650/AVR 365 only): when the Ir sensor on the front panel is blocked (such as when the Avr is installed inside a cabinet), connect an optional Ir receiver to the Ir remote In jack. the Ir remote out jack may be connected to the Ir input of a compatible product to enable remote control through the Avr.

Fan Vents: these vents are used by the Avr’s fan to cool the system. maintain a clearance of at least three inches (75mm) from the nearest surface to avoid overheating the unit. It is normal for the fan to remain off at most normal volume levels. An automatic temperature sensor turns the fan on only when it is needed.

IMPORTANT NOTE: never block the fan vents. doing so could allow the Avr to overheat to dangerous levels.

ENGLISH

AVR

System Remote Control Functions

Avr power on/off buttons

Source Selector buttons (Avr 2650/Avr 265)

Source Selector buttons (Avr 3650/Avr 365)

Audio effects button

video modes button

last channel button

back/exit button

ok button

backlight button

(Avr 3650/Avr 365 only)

A/b/c/d buttons

volume up/down buttons

mute button

Info button

Avr button

Zone Selector

Switch

Ir transmitter lens

device power on/off buttons

Surround modes button

number buttons

Activity button

menu button

up/down/left/right buttons

disc menu button

channel up/down and page buttons

transport control buttons

Sleep button

learn button

(Avr 3650/Avr 365 only)

Continued on next page

AVR

System Remote Control Functions, continued

In addition to controlling the Avr, the Avr remote is capable of controlling eight other devices, including an ipod/iphone device docked in a the bridge IIIp docking station connected to the Avr. during the installation process, you may program the codes for each of your source components into the remote. (See program the remote to control your Source devices and tv, on page 23, for programming information.) to operate a component, press its Source Selector button to change the remote’s control mode.

A button’s function depends on which component is being controlled. See table A13 in the Appendix for listings of the functions for each type of component. most of the buttons on the remote have dedicated functions, although the precise codes transmitted vary depending on the specific device being controlled. due to the wide variety of functions for various source devices, we have included only a few of the most-often used functions on the remote: alphanumeric keys, transport controls, television-channel control, menu access and power on and off. buttons dedicated to the Avr – Avr power on/off, Audio effects, video modes, Surround modes, volume, mute and Sleep Settings – are available at any time, even when the remote is controlling another device. to return the remote to the Avr control mode at any time, press the Setup button.

AVR Power On/Off buttons: press these buttons to turn the Avr on and off. the main power switch on the Avr’s rear panel must be on for this button to work.

IR Transmitter Lens: As buttons are pressed on the remote, infrared codes are emitted through this lens.

Device Power On/Off buttons: press a device’s Source Selector button, then press these buttons to turn the device on and off.

Source Selector buttons: press one of these buttons to select a source device, e.g., blu-ray, cable/Sat, radio, etc. this action will also turn on the Avr and switch the remote’s control mode to operate the selected source device. NOTE: the first press of the radio Source Selector button switches the Avr to the last-used tuner band (Am, fm or SIrIuS). each successive press changes the band.

Audio Effects button: press this button to access the Audio effects submenu, which allows adjustment of the Avr’s tone and other audio controls. See the Set up your Sources section, on page 26, for more information.

Video Modes button: press this button for direct access to the video modes submenu, which contains picture adjustments you can use after you have adjusted the picture settings on your tv or video display. See the Advanced functions section, on page 33, for more information.

Surround Modes button: press this button to access the Surround modes submenu. Select a surround-mode category: Auto Select, virtual Surround, Stereo, movie, music or game. when you select the category, it is highlighted and the surround mode changes.

to change the surround mode for the selected category, press the ok button when the menu line is highlighted and use the up/down buttons to select one of the available surround-mode options. press the ok button; or press the back/exit button to exit the Surround modes menu and display the next higher menu in the hierarchy. See the Advanced functions section, on page 33, for more information.

Number buttons: use these buttons to enter numbers for radio-station frequencies or to select station presets.

Last Channel button: when controlling a cable, satellite or hdtv set-top box or a tv, press this button to return to the previous television channel.

Activity button: with this button you can program the remote to store up to 11 different macros (Activities). (A macro is a series of commands that are transmitted by a single button press.) execute a macro by pressing this button, followed by the number button (or the Avr power on button) into which you programmed the macro. See programming macro (Activity) commands, on page 41, for more information.

Back/Exit button: press this button to return to the previous menu or to exit the menu system.

Menu button: this button is used within the tuner menus (including SIrIuS radio) and the bridge IIIp control menu, and is also used to display the main menu on some source devices. to display the Avr’s menu system, press the Setup button.

Up/Down/Left/Right buttons: these buttons are used to navigate the menu system and to operate the tuner.

OK button: this button is used to select items from the menu system.

Backlight button (AVR 3650/AVR 365 only): press this button to illuminate the buttons on the remote. press it again to turn the backlight off, or wait 5 seconds after the last button press for the light to turn off on its own.

Disc Menu button: to display the disc’s menu while a dvd or blu-ray disc is playing, press the blu-ray Source Selector button, then press this button.

A/B/C/D buttons: these buttons can be used as additional source buttons and can also operate certain functions when used with some source devices. See table A13 in the Appendix for details. these buttons are also used with a teletext®-capable television if your broadcast, cable or satellite provider offers teletext service.

Volume Up/Down buttons: press these buttons to raise or lower the volume.

Channel Up/Down and Page buttons: when the tuner has been selected, press these buttons to select a preset radio station. while operating a cable, satellite or hdtv set-top box or a television, press these buttons to change channels.

Mute button: press this button to mute the Avr’s speaker-output connectors and headphone jack. to restore the sound, press this button or adjust the volume.

Transport Control buttons: these buttons are used to control source devices and the bridge IIIp.

Info button: press to display the Avr’s Info menu, which contains the settings for the current source.

Setup button: press to display the Avr’s main menu or to switch the remote to the Avr control mode.

Sleep button: press this button to activate the sleep timer, which turns off the receiver after a programmed period of time. each press increases the time by 10 minutes, up to 90 minutes – ending with the “Sleep off” message.

Learn button (AVR 3650/AVR 365 only): the Avr 3650/Avr 365 remote is capable of “learning” individual Ir codes from the original remote that came with a source device. See program the remote to control your Source devices and tv, on page 23, for more information.

Zone Selector switch: use this switch to select whether the Avr commands will affect the main listening area (Zone 1) or the remote zone of a multizone system (Zone 2). for normal operation, leave the switch in the Zone 1 position.

ENGLISH

AVR

Zone 2 Remote Control Functions (AVR 3650/AVR 365 only)

Ir transmitter lens

power off button

Source Selector

buttons

Avr button

back/exit button

ok button

Zone Selector

button

mute button

Sleep button

menu button

up/down/left/right buttons

volume up/down buttons

transport control buttons

Zone Indicator light

Continued on next page

AVR

Zone 2 Remote Control Functions (AVR 3650/AVR 365 only), continued

by installing an Ir receiver in the remote zone of a multizone system and connecting it to the Avr’s Zone 2 Ir Input connector, you can use the Zone 2 remote to control the sound in the remote zone from within the remote zone. you can use it to control the Avr’s power, volume and mute functions or to select a source input for the remote zone, and to control a harman kardon source device connected to one of the Avr’s remote Ir out connectors. See connect Ir equipment, on page 22, for more information.

you can also use the Zone 2 remote in the main listening room to control the Avr and harman kardon blu-ray disc™, dvd, cd or tape players. when the Zone 2 remote is in the Zone 1 control mode (the remote’s Zone Indicator light will turn green), its power, volume and mute controls will affect only the main listening area. to restore operation to the remote zone, press the remote’s Zone Selector button so that its Zone Indicator light turns red.

IR Transmitter lens: As buttons are pressed on the remote, infrared codes are emitted through this lens.

Power Off button: press this button to turn the Avr off.

Mute button: press to mute the Avr’s remote-zone speakers. to restore the sound, press this button, adjust the volume or turn off the multizone system. make sure to switch the remote to Zone 2 mode so that only the remote zone will be affected.

Source Selector buttons: with the remote in Zone 2 mode, press one of these buttons to select a source device for the remote zone. pressing the button will also turn on the multizone system and switch the remote to the selected source device’s control mode. you may select a different external source device than that for the main room, but not different tuner bands. If you select the same source as that for the main room, any commands sent to the source device will affect both zones. the first press of the radio Source Selector button switches the Avr to the last-used tuner band (Am, fm or SIrIuS). each successive press changes the band.

AVR button: press this button to turn on the Avr and select the last-used source. this button is also used to switch the remote control to Avr control mode.

Back/Exit button: press this button to return to the previous menu or to exit the menu system.

Up/Down/Left/Right buttons: these buttons are used to navigate the menu system and to operate the tuner.

OK button: this button is used to select items from the menu system.

Volume Up/Down buttons: press to raise or lower the volume level in the remote zone.

Transport Control buttons: these buttons are used to control source devices and the bridge IIIp.

Zone Selector button and Zone Indicator light: each press of the Zone Selector button determines whether the Avr commands will affect the main listening area (Zone 1) or the remote zone (Zone 2). the Zone Indicator light will turn green when Zone 1 has been selected, and red when Zone 2 has been selected. the Zone Indicator light will also light up briefly when any button is pressed.

ENGLISH

AVR

Introduction to Home Theater

This introductory section will help you to familiarize yourself with some basic concepts unique to multichannel surround-sound receivers, which will make it easier for you to set up and operate your AVR.

Typical Home Theater System

A home theater typically includes an audio/video receiver, which controls the system and supplies amplification for the loudspeakers; a disc player; a source component for television broadcasts (cable box, satellite dish receiver, HDTV tuner or antenna connected to the TV); a TV or video display; and multiple loudspeakers.

Multichannel Audio

The main benefit of a home theater system is its ability to produce “surround sound.” Surround sound uses multiple speakers and amplifier channels to immerse you in the audio/video presentation for a dramatically increased sense of realism.

Your AVR may have up to seven main speakers connected directly to it, plus a subwoofer. Each main speaker is powered by its own amplifier channel inside the AVR. A system with more than two speakers is called a multichannel system. The different main speaker types in a home theater system are:

•• Front Left and Right: The front left and right speakers are used as in a two-channel system. In many surround-sound modes, these speakers are secondary, while the main action, especially dialogue, is reproduced by the center speaker.

•• Center: When you are watching movies and television programs, the center speaker reproduces most of the dialogue and other soundtrack information, anchoring it with the picture. When you are listening to a musical program, the center speaker helps to create a seamless front soundstage, creating a realistic “you-are-there” listening experience.

•• Surround Left and Right: The surround left and right speakers produce ambient sounds that help create a realistic and immersive surround-sound environment. They also help recreate directional sound effects such as aircraft flyovers.

•• Surround Back Left and Right: Surround back channel speakers are used with surround modes such as the Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, DTS-ES® (Discrete and Matrix), DTS-HD™ High Resolution Audio, DTS-HD Master Audio™ and Logic 7® 7.1 modes that are designed for 7.1-channel systems.

The surround back channel speakers are optional. If your system does not include surround back left and right speakers, you can set up your AVR with a 5.1-channel surround-sound system in the main listening area, and you can reassign the surround back channel amplifiers to power loudspeakers located in another room in a multizone system. (Alternately, you can reassign the surround back channel amplifiers to power front height speakers for use with Dolby Pro Logic IIz. See Manual Speaker Setup, on page 36, for more information.)

Many people expect the surround speakers to play as loudly as the front speakers. Although you will calibrate all of the speakers in your system to sound equally loud at the listening position, most artists use the surround speakers for ambient effects only, and they create their programs to steer relatively little sound to these speakers.

•• Subwoofer: A subwoofer is designed to play only the lowest frequencies (the deep bass). It augments smaller, limited-range main speakers that are usually used for the other channels. Many digital-format programs, such as movies recorded in Dolby Digital, contain a low-frequency effects (LFE) channel that is directed to the subwoofer. The LFE channel packs the punch of a rumbling train or airplane, or the power of an explosion, adding realism and excitement to your home theater. Some people use two subwoofers for additional power and for even distribution of the sound.

Introduction to Home Theater

Surround Modes

There are different theories as to the best way to present surround sound and to distribute each audio channel’s sounds to the surround-sound system’s speakers. A variety of algorithms have been developed in an effort to recreate the way we hear sounds in the real world, resulting in a rich variety of options. Several companies have developed different surround-sound technologies, all of which can be accurately reproduced by your AVR:

•• Dolby Laboratories: Dolby TrueHD, Dolby Digital Plus, Dolby Digital, Dolby Digital EX, Dolby Pro Logic® IIx and IIz.

•• DTS: DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS, DTS-ES (Discrete and Matrix), DTS Neo:6®, DTS 96/24™.

•• HARMAN International: Logic 7®, HARMAN virtual speaker, HARMAN headphone.

•• Stereo Modes: Generic modes that expand upon conventional two-channel stereo, including 5CH and 7CH Stereo.

Appendix Table A12, on page 50, contains detailed explanations of the different surround-sound options available on your AVR. Digital surround-sound modes, such as the Dolby Digital and DTS modes, are available only on specially encoded programs, such as those available via HDTV, DVD and Blu-ray Disc media and digital cable or satellite television. Other surround modes may be used with digital and analog signals to create a different surround presentation or to use a different number of speakers. Surround-mode selection depends upon the number of speakers in your system, the program you are watching or listening to, and your personal tastes.

AVR

Place Your Speakers

Determine the locations for your system’s speakers according to their manufacturer’s directions and the layout of your listening room. Use the illustrations below as a guide for 7.1-channel and 5.1-channel systems.

To create the most realistic surround-sound environment possible, you should place your speakers in a circle with the listening position at its center. You should angle each speaker so it directly faces the listening position. Use the diagrams below as a guide.

TV	SUB
C	SUB
FL	FR

Speaker Positioning for 5.1-Channel Systems

TV	SUB
C	SUB
FL	FR

SBL	SBR
TV	SUB
C	SUB
FL	FR
FHL*	FHR*

*FHL and FHR speakers should be at least 3 ft (0.9m) above the FL and FR speakers.

Speaker Positioning for 7.1-Channel Systems

(Top: with Surround Back Speakers; Bottom: with Front Height Speakers)

NOTE: In a 7.1-channel system, you must choose to use either surround back speakers or front height speakers – you cannot use both simultaneously.

Placing the Left, Center and Right Speakers

Place the center speaker either on top of, below or mounted on the wall above or below the TV or video display screen. Place the front left and right speakers along the circle, about 30 degrees from the center speaker and angled toward the listener.

Place the front left, front right and center speakers at the same height, preferably at about the same height as the listener’s ears. The center speaker should be no more than 2 feet (0.6m) above or below the left/right speakers. If you’re using only two speakers with your AVR, place them in the front left and right positions.

Placing the Surround Speakers in a 5.1-Channel System

You should place the left and right surround speakers approximately 110 degrees from the center speaker, slightly behind and angled toward the listener. Alternatively, place them behind the listener, with each surround speaker facing the opposite-side front speaker. You should place the surround speakers 2 feet – 6 feet (0.6m – 1.8m) higher than the listener’s ears.

Placing the Surround Speakers in a 7.1-Channel System

In a 7.1-channel system, place the side surround speakers 90 degrees from the center speaker, directly to either side of the listening position. Place the surround back left and right speakers 150 degrees from the center speaker, directly facing the opposite-side front speaker. You should place all the surround speakers 2 feet – 6 feet (0.6m – 1.8m) higher than the listener’s ears.

Placing Front Height Speakers in a 7.1-Channel System

Your AVR includes Dolby Pro Logic IIz decoding, which uses the AVR’s Assigned Amp channels as front height channels. The addition of front height channels – an additional pair of speakers positioned above the front left and right speakers – produces a surroundsound experience with added depth and dimension by creating lifelike sound that comes at you from varying heights.

We recommend placing front height speakers at least 3 feet (0.9m) higher than the front left and front right speakers, and directly above or farther apart than the front left and right speakers. The higher and further apart you place the front height speakers, the more you should angle them down and in toward the listening position.

NOTE: Your receiver will sound its best when the same model or brand of loudspeaker is used for all positions.

Placing the Subwoofer

Because a room’s shape and volume can have a dramatic effect on a subwoofer’s performance, it is best to experiment with placement so that you will find the location that produces the best results in your particular listening room. With that in mind, these rules will help you get started:

•• Placing the subwoofer next to a wall generally will increase the amount of bass in the room.

•• Placing the subwoofer in a corner generally will maximize the amount of bass in the room.

•• In many rooms, placing the subwoofer along the same plane as the left and right speakers can produce the best integration between the sound of the subwoofer and that of the left and right speakers.

•• In some rooms, the best performance could even result from placing the subwoofer behind the listening position.

A good way to determine the best location for the subwoofer is by temporarily placing it in the listening position and playing music with strong bass content. Move around to various locations in the room while the system is playing (putting your ears where the subwoofer would be placed), and listen until you find the location where the bass performance is best. Place the subwoofer in that location.

ENGLISH

AVR

Types of Home Theater System Connections

There are different types of audio and video connections used to connect the AVR to your speakers, your TV or video display, and your source devices. The Consumer Electronics Association has established the CEA® color-coding standard.

Analog Audio Connection	Color
Front Left/Right	White/Red

Center	Green

Surround Left/Right	Blue/Gray

Surround Back/Front Height Left/Right	Brown/Tan

Subwoofer	Purple

Digital Audio Connection	Color

Coaxial (input or output)	Orange

Optical Input	Black

Optical Record Output	Gray

Analog Video Connection	Color

Component Video	Red/Green/Blue

Composite Video	Yellow

Speaker Connections

Speaker cables carry an amplified signal from the AVR’s speaker terminals to each loudspeaker. They contain two wire conductors, or leads, that are differentiated in some way, such as with colors or stripes.

The differentiation helps you maintain proper polarity, without which your system’s lowfrequency performance can suffer. Each speaker is connected to the AVR’s speakeroutput terminals using two wires, one positive (+) and one negative (–). Always connect the positive terminal on the speaker, which is usually colored red, to the positive terminal on the receiver, which is colored as indicated in the Connection Color Guide Table, above. The negative terminals on the speakers and the AVR are black.

Your AVR uses binding-post speaker terminals that can accept bare-wire cables or banana plugs. Bare-wire cables are installed as shown below:

1. Unscrew Cap

2. Insert Bare Wire

3. Tighten Cap

Banana plugs are inserted into the hole in the middle of the terminal cap, as shown below:

A. Tighten Cap	B. Insert Banana Connector
	into Hole in Cap

Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker (usually red), and the black (–) terminal on the AVR to the (–) terminal on the speaker (usually black).

IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the other terminal. Touching wires can cause a short circuit that can damage your receiver or amplifier.

Subwoofer Connections

The subwoofer is a speaker dedicated to reproducing only the low (bass) frequencies, which require more power. To obtain the best results, most speaker manufacturers offer powered subwoofers that contain their own amplifiers. Use a single RCA audio cable to make a line-level (non-amplified) connection from the AVR’s Subwoofer connector to a corresponding input jack on the subwoofer.

Although the AVR’s purple subwoofer output looks similar to a full-range analog audio jack, it is filtered so that only the low frequencies pass through it. Don’t connect this output to any device other than a subwoofer.

Source Device Connections

Audio and video signals originate in source devices (components where a playback signal originates) such as your Blu-ray Disc or DVD player, CD player, DVR (digital video recorder) or other recorder, tape deck, game console, cable or satellite television tuner, an iPod or iPhone (docked in an optional The Bridge IIIP docking station) or an MP3 player. The AVR’s FM/AM tuner also counts as a source, even though no external connections are needed other than the FM and AM antennas and an optional SIRIUS tuner module. Separate connections are required for the audio and video portions of the source device’s signal, except for digital HDMI connections. The types of connections you use will depend upon the capabilities of the source device and of your TV or video display.

Digital Audio Connections – HDMI

There are two types of audio connections – digital and analog. Digital audio signals are required for listening to sources encoded with digital surround modes, such as Dolby Digital and DTS, or for uncompressed PCM digital audio. Your AVR has three types of digital audio connections: HDMI, coaxial and optical. Do not use more than one type of digital audio connection for each source device. However, it’s okay to make both analog and digital audio connections to the same source.

Your AVR is equipped with five rear-panel HDMI input connectors, and one HDMI monitor output connector. (The AVR 3650 and AVR 365 also have a front-panel HDMI input connector.) HDMI technology enables digital audio and video information to be carried using a single cable, delivering the highest quality picture and sound. If your TV or video display device has an HDMI input connector, make a single HDMI connection from each source device to the AVR. Usually, a separate digital audio connection is not required.

The AVR’s HDMI monitor output connection contains an Audio Return Channel (ARC) that carries a digital audio signal from your TV or video display back to the AVR. It allows you to listen to HDMI devices that are connected directly to your TV (such as an Internet connection) without making an additional connection from the device to the AVR. The ARC signal is active when the TV source is selected. See System Settings, on page 39, for more information.

The HDMI connector is shaped for easy plug-in (see illustration, below), and HDMI cable runs are limited to about 10 feet (3m). If your video display has a DVI input and is HDCP-compliant, use an HDMI-to-DVI adapter (not included), and make a separate audio connection.

AVR

Types of Home Theater System Connections

Digital Audio Connections – Coaxial

Coaxial digital audio jacks are usually color-coded in orange. Although they look like standard RCA-type analog jacks, you should not connect coaxial digital audio outputs to analog inputs or vice versa.

Digital Audio Connections – Optical

Optical digital audio connectors are normally covered by a shutter to protect them from dust. The shutter opens as the cable is inserted. Optical input connectors are colorcoded using a black shutter, while optical outputs use a gray shutter.

Analog Audio Connections

Two-channel analog connections require a stereo audio cable, with one connector for the left channel (white) and one for the right channel (red). These two connectors are attached to each other.

For source devices that have both digital and analog audio outputs, you may make both connections. If you are going to be setting up a multizone system, remember that Zone 2 is an audio-only zone (the AVR does not have a Zone 2 video output). Therefore, make analog connections for any audio source devices (such as a CD changer) that you will want available for listening in Zone 2 at all times.

The analog connections also feed the analog record outputs. You may record materials from Blu-ray Disc recordings, DVDs or other copy-protected sources using only analog connections. Remember to comply with all copyright laws if you choose to make a copy for your own personal use.

The Bridge IIIP Connection

Your AVR includes a proprietary, dedicated connector for an optional The Bridge IIIP docking station for the iPod or iPhone. The Bridge IIIP outputs analog audio to the AVR and is available as a source to Zone 2 in a multizone system.

Video Connections

Many source devices output both audio and video signals (e.g., Blu-ray Disc, DVD player, cable television box, HDTV tuner, satellite box, VCR, DVR). In addition to an audio connection as described above, make a video connection for each of these source devices. Make only one type of video connection for each device.

Digital Video Connections

If you have already connected a source device to one of the AVR’s HDMI input connectors, you have automatically made a video connection for that device, since the HDMI cable carries both digital audio and digital video signals.

Analog Video Connections – Composite Video

Your AVR uses two types of analog video connections: composite video and component video.

Composite video is the basic connection most commonly available. Both the chrominance (color) and luminance (intensity) components of the video signal are transmitted using a single cable. The jack is usually color-coded yellow and looks like an analog audio jack. Do not connect a composite video jack to an analog audio or coaxial digital audio jack, or vice versa.

Analog Video Connections – Component Video

Component video separates the video signal into three components – one luminance (“Y”) and two sub-sampled color signals (“Pb” and “Pr”) – that are transmitted using three separate cables that are color-coded green (Y), blue (Pb) and red (Pr). Component video cables that join three separate green, blue and red connectors into a single cable are sold separately.

If your TV or video display has an HDMI connection, we recommend it as the best quality connection. Your AVR converts composite and component analog video input signals to the HDMI format, upscaling them to high-definition 1080p resolution.

ENGLISH

AVR

Radio Connections

Your AVR uses separate terminals for the included FM and AM antennas. The FM antenna uses a 75-ohm F-connector.

The AM antenna connector uses spring-clip terminals. After assembling the antenna as shown below, press the levers to open the connectors, insert the bare wires into the openings, and release the levers to secure the wires. The antenna wires are not polarized, so you can insert either wire into either connector.

SIRIUS Satellite Radio

To enjoy SIRIUS satellite radio, purchase a SIRIUSConnect tuner module and a subscription to the SIRIUS service. Visit www.sirius.com for information on SIRIUSConnect tuner modules. The SiriusConnect modules include an eight-pin DIN cable for connection to the eight-pin jack on the AVR, allowing you to control the tuner module via the AVR. Although you may also use a “plug-and-play” tuner module equipped with standard audio connections, you will not be able to use the AVR to control the SIRIUS tuner.

Network Connector

The AVR’s Network connector allows you to enjoy Internet radio or content from other DLNA-compatible devices that are connected to the same network. Use a Cat. 5 or Cat. 5E cable to connect the AVR’s RJ-45 connector to your home network.

Types of Home Theater System Connections

USB Port

The USB port on your AVR is used for firmware upgrades. If an upgrade for the AVR’s operating system is released in the future, you will be able to download it to the AVR using this port. Complete instructions will be provided at that time.

In addition to performing firmware upgrades, the AVR 3650/AVR 365 can play MP3 and WMA audio files from a USB device inserted into the USB port. Insert the device into the USB port with the device’s plug oriented so it fits all the way into the port. You may insert or remove the device at any time – there is no installation or ejection procedure.

IMPORTANT: Do not connect a PC or other USB host/controller to the AVR’s USB port, or you may damage both the AVR and the other device.

RS-232 Connector

Your AVR’s RS-232 serial port may be connected to an external control system to allow it to transmit control commands to the AVR. The port is bidirectional so that the AVR can transmit status updates to the control device. Connecting and using the RS-232 port requires considerable technical knowledge and is best left to a professional custom installer.

AVR

Making Connections

CAUTION: Before making any connections to the audio/video receiver, ensure that the AVR’s AC cord is unplugged from the receiver and the AC outlet. Making connections with the receiver plugged in and turned on could damage the speakers.

Connect Your Speakers

After you have placed your loudspeakers in the room as explained in Place Your Speakers, on page 13, connect each speaker to its color-coded terminal on the AVR as explained in Speaker Connections, on page 14. Connect the speakers as shown in the illustration.

Connect Your Subwoofer

Use a single RCA audio cable to connect the AVR’s Subwoofer connector to your subwoofer as explained in Subwoofer Connections, on page 14. Consult your subwoofer’s user manual for specific information about making connections to it.

AVRAVRSubwooferoofer		PPooweredd
Conn		Subwooferr
Connector	Single	Subwooferr
	Single
	Single
	RCA Audio Cable
	RCA Audio Cable
	(notsupplied)

Connect Your TV or Video Display

If your TV has an HDMI connector: Use an HDMI cable (not included) to connect it to the AVR’s HDMI Monitor Out connector. You do not need to make any other connections to your TV from the receiver or from any of your video source components.

NOTE: If you installed front height speakers, connect them as shown for the SBL and SBR speakers.

Receiver

HDMI Monitor Out TV

Connector

HDMI Cable (not supplied)

If your TV does not have an HDMI connector: Use a composite video cable (not included) to connect the AVR’s Composite Monitor Out connector to your TV’s composite video connector.

Receiver

Composite TV

Monitor Out

Connector

Composite Video Cable (not supplied)

NOTE: The HDMI connection to your TV is preferred. If you use the composite video connection to your TV, you will not be able to view the AVR’s on-screen menus.

ENGLISH

AVR

Making Connections

Connect Your Audio and Video Source Devices

Your receiver has several different types of input connectors for your audio and video source devices: HDMI, component video, composite video, optical digital audio, coaxial digital audio and analog audio. The connectors are not labeled for specific types of source devices; they are labeled numerically, so you can connect your devices according to your individual system’s makeup.

Your AVR’s various source buttons have default assignments to different input connectors (listed in the “Default Source Button” column of the table below). For ease of setup, you should connect each source device to the connector where the corresponding default

source button is assigned (e.g., connect your Blu-ray Disc player to HDMI 1). However, you can connect your source devices as you wish and re-assign any of the source buttons to any of the input connectors listed in the table according to where you actually connect each of your source devices.

As you connect your various source components, fill out the “Connected Component” column in the table – it will make it easier for you to assign the various source buttons after you have completed making all of the connections. (You will make any changes to the source-button assignments and fill in the “Assigned Source Button” column later in the setup process.)

AVR Input Connector	Connected Component	Default Source Button			Assigned
AVR Input Connector	Connected Component	AVR 3650/AVR 365	AVR 2650/AVR 265		Source Button
		AVR 3650/AVR 365	AVR 2650/AVR 265		Source Button

HDMI 1		Blu-ray		Blu-ray/TV

HDMI 2		Cable/Sat		Cable/Sat

HDMI 3		Game		Game

HDMI 4		Media Server		Media Server

HDMI 5		TV		DVR

(AVR 3650/AVR 365 only) HDMI Front		Aux		– –


Component Video 1		A (red)		A (red)

Component Video 2		B (green)		B (green)

Composite Video 1		C (yellow)		C (yellow)

Composite Video 2		D (blue)		D (blue)


Optical Digital Audio 1		A (red)		A (red)

Optical Digital Audio 2		B (green)		B (green)

Coaxial Digital Audio Input 1		C (yellow)		C (yellow)

Coaxial Digital Audio Input 2


Analog Audio In 1		D (blue)		D (blue)

Analog Audio In 2				Aux

Analog Audio In 3


Monitor Output Connector	Connected Component	— — — —			— — — —

HDMI Monitor Out		— — — —			— — — —

Composite Video Monitor Out		— — — —			— — — —


Record Output Connector	Connected Component	— — — —			— — — —

Composite Video Rec Out		— — — —			— — — —

Optical Digital Audio Out		— — — —			— — — —

Input Connections and Assigned Source Buttons

AVR

Making Connections

Connect Your HDMI Devices

If any of your source devices have HDMI connectors, using them will provide the best possible video and audio performance quality. Since the HDMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via an HDMI cable.

Receiver

HDMI Connectors

HDMI Cable (not supplied)

To HDMI

Output

HDMI-Equipped

Source Device

NOTE: If you have HDMI devices (such as an Internet connection) already connected directly to your TV, you can feed their sound to the AVR via the HDMI Monitor Out connector’s Audio Return Channel, and they will not require additional connections to the AVR.

Connect Your Component Video Devices

If any of your video source devices have component video connectors (and do not have HDMI connectors), using the component video connectors will provide superior video performance. You will also need to make an audio connection from the device to the receiver.

Receiver

Video Connectors

Component Video

Cable (not supplied)

To Component Video

Outputs

Component Video-Equipped

Source Device

Connect Your Composite Video Devices

Use composite video connectors for video source devices that don’t have HDMI or component video connectors. You will also need to make an audio connection from the source device to the receiver.

Receiver

Video Connectors

Composite Video

Cable (not supplied)

To Composite Video

Output

Composite Video-Equipped

Source Device

Connect Your Optical Digital Video Devices

If your non-HDMI source devices have optical digital outputs, connect them to the AVR’s optical digital audio connectors. NOTE: Make only one type of digital connection (HDMI, optical or coaxial) from each device.

Receiver

Digital Audio Connectors

Optical Digital Audio

Cable (not supplied)

To Optical Digital

Audio Output

Optical Digital-Equipped

Source Device

Connect Your Coaxial Digital Audio Devices

If your non-HDMI source devices have coaxial digital outputs, connect them to the AVR’s coaxial digital audio connectors. NOTE: Make only one type of digital connection (HDMI, optical or coaxial) from each device.

Receiver

Digital Audio Connectors

Coaxial Digital Audio

Cable (not supplied)

To Coaxial Digital

Audio Output

Coaxial Digital-Equipped

Source Device

Connect Your Analog Audio Devices

Use the AVR’s analog audio connectors for source devices that don’t have HDMI or digital audio connectors. NOTE: If you’re installing a multizone system, make analog audio connections for any source devices you want to be able to listen to in Zone 2. Only analog sources are available in Zone 2.

Receiver

Analog Audio Connectors

Stereo Audio Cable

(not supplied)

To Stereo Analog

Audio Output

Analog Source Device

ENGLISH

+ 43 hidden pages