GASOLINE AUGER DRILL
1.5 HP
Model 95346
Assembly And Operation Instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
CAUTION!
Your Warranty Is Voided If:
You do not operate the Auger Drill with the proper 25:1 unleaded fuel/2-cycle oil mix in its fuel tank. Never run the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper fuel mix, low or no fuel mix, will permanently damage the unit.
You do not operate the Auger Drill with the proper amount of SAE 80-90 gear oil in its Gearbox. Never run the Auger Drill with low or no gear oil. Running the Auger Drill with low or no gear oil will permanently damage the unit.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
To prevent serious injury, read and understand all warnings and instructions before use.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 07b, 07e
|
|
|
SPECIFICATIONS |
|
|
Engine Specifications |
1.5 HP / 52cc / Single Cylinder / 2-Stroke / Recoil Start |
Fuel Required |
25:1 Unleaded Gasoline (89 octane or better) & 2 Cycle Oil Mixture |
Fuel Tank Capacity |
0.26 Gallon |
Recommended Gear Oil |
SAE 80 – 90 Weight Gear Oil |
Rotation |
Single Rotation Only (Clockwise) |
Drilling Speed |
150 RPM |
Maximum Drilling Depth |
1’ 10” |
Auger Diameter |
4” |
Overall Bit Length |
2’ 6-3/4” Long |
Cutting Edge Length |
2’ Long |
Drive Shaft |
7/8” Diameter x 1-1/2” Long |
Accessories |
Auger Bit / Fuel & Oil Mixing Container / Spark Plug Wrench |
|
Flat Head Screwdriver / Hex Keys (Qty. 2) / Storage Bag |
Weight |
17-1/4 lb. (without fuel and oil) |
This product requires a 25:1 ratio of unleaded fuel and 2-cycle oil to be added to its fuel tank before starting. Attempting to start the Engine with an improper fuel mix, low or no fuel mix WILL ruin the Engine and void the warranty.
This product requires the proper amount of SAE 80-90 gear oil in its Gear Case before starting. Attempting to start the Auger Drill with low or no gear oil WILL ruin the
Gear Case and void the warranty.
The Engine’s Carburetor may need to be adjusted by a qualified mechanic for efficient high-altitude use.
The Emission Control System for this product’s engine is warranted for standards set by the U.S. Environmental Protection Agency. For warranty information, refer to the last pages of this manual.
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference.
REV 07b, 07e
SKU 95346 |
For technical questions, please call 1-800-444-3353 |
PAGE |
GENERAL SAFETY RULES AND PRECAUTIONS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS
WORK AREA
1.Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2.Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
3.Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Provide barriers or shields as needed. Children should not be allowed in the work area.
PERSONAL SAFETY
1.Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
2.Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
3.Avoid accidental starting. Make sure to remove the Spark Plug before performing any service, maintenance, or cleaning procedures on the unit.
4.Remove adjusting keys or wrenches before turning the Auger Drill on. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury.
5.Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations.
TOOL USE AND CARE
1.Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
SKU 95346 |
For technical questions, please call 1-800-444-3353 |
PAGE |
2.Do not use the Auger Drill if the Kill Switch does not turn it off. Any tool that cannot be controlled with its Kill Switch is dangerous and must be replaced.
3.Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
4.Maintain tools with care. Properly maintained tools are less likely to malfunction and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.
5.Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
6.Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool.
SERVICE
1.Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.
2.When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual.
Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES AND PRECAUTIONS
1.IMPORTANT! Your Warranty is voided if:
a.You do not operate the Auger Drill with the proper 25:1 fuel mix in its fuel tank. Never run the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper fuel mix, low or no fuel mix, will permanently damage the unit.
b.You do not operate the Auger Drill with the proper amount of SAE 80-90 gear oil in its Gearbox. Never run the Auger Drill with low or no gear oil. Running the Auger Drill with low or no gear oil will permanently damage the unit.
2.Maintain labels and nameplates on the Auger Drill. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
3. |
Always wear safety equipment. When operating the Auger Drill, |
|
|
always wear ANSI-approved safety impact eye goggles, hearing |
|
|
protection, heavy duty work gloves, sturdy steel-toed work boots, |
|
|
and head protection. |
|
SKU 95346 |
For technical questions, please call 1-800-444-3353 |
PAGE |
4.Never leave the Auger Drill unattended when it is running. Turn off the Engine before leaving.
5.Do not allow children and other unauthorized people to handle or play with the Auger Drill. Never leave the drill unattended in an area accessible to children.
6.Always maintain a firm grip on the Auger Drill with both hands and be aware of the strong start-up torque of the tool.
7.Always keep your thumb near the Kill Switch in the event the Auger Drill must be turned off immediately.
8.Do not use the Auger Drill if the Auger is dull, bent, or damaged.
9.Avoid accidental damage to underground pipes, electric lines, cables, etc. and possible personal injury. Always contact your local public utility companies (gas, water, electric, cable, etc.) prior to drilling in an unknown area.
10.Always drill with the Engine running at full speed. Fully squeeze the Speed Control Lever and maintain a steady drilling speed.
11.Always keep the Auger clean and sharp.
12.Keep all guards and safety devices in proper working order and properly adjusted.
13.Before starting the Engine, make sure the Auger is not contacting any object.
14.When shutting off the Engine, and make sure the Auger has stopped before setting the tool down.
CARBON MONOXIDE PRECAUTIONS
This Auger Drill is designed for outdoor use only. Do not operate the Auger Drill in a closed area or in a poorly ventilated area. When running, the Engine of this product produces carbon monoxide, a colorless, odorless, toxic gas that, when inhaled, can cause serious personal injury or death.
FIRE AND EXPLOSION PRECAUTIONS
1.Gasolinefuelandfumesareflammable,andpotentiallyexplosive. Use proper fuel storage and handling procedures. Always have multiple ABC class fire extinguishers nearby.
2.Keep the Auger Drill and surrounding areas clean at all times.
SKU 95346 |
For technical questions, please call 1-800-444-3353 |
PAGE |
3.When spills of fuel or oil occur, they must be cleaned up immediately. Dispose of fluids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container.
4.Never store fuel or other flammable materials near the Auger Drill.
5.Do not smoke, or allow sparks, flames, or other sources of ignition around the Auger Drill.
6.Keep grounded conductive objects, such as tools, away from exposed, live electrical parts and connections to avoid sparking or arcing. These events could ignite fumes or vapors.
7.Do not refill the Fuel Tank while the Engine is running or while the Engine is still hot. Do not operate the Auger Drill with known leaks in the fuel system.
8.Use only Engine manufacturer recommended fuel and oil.
MECHANICAL PRECAUTIONS
1.Prior to performing service, maintenance, or cleaning procedures, always allow the Engine to completely cool. Then, remove the spark plug from the Engine.
2.Do not alter or adjust any part of the Auger Drill or Engine that is assembled and supplied by the manufacturer.
3.Always follow and complete scheduled Auger Drill and Engine maintenance.
CHEMICAL PRECAUTIONS
1.Avoid contact with hot fuel, oil, exhaust fumes, and solid surfaces.
2.Avoid body contact with fuels, oils, and lubricants used in the Auger Drill and Engine. If swallowed, seek medical treatment immediately. Do not induce vomiting if fuel is swallowed. For skin contact, immediately wash with soap and water. For eye contact, immediately flush eyes with clean water.
NOISE PRECAUTIONS
Prolonged exposure to high noise levels is hazardous to hearing. Always wear proper hearing protection when operating or working around the Auger Drill when it is running.
SKU 95346 |
For technical questions, please call 1-800-444-3353 |
PAGE |
Loading...