Haier HSU-09LQA13-R2-DB-WT, AS12GB2LAA, HSU-18LEK03-R2-DB, HSU-10LQA13, AS12GS1ERA User Manual

SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL

HSU-10LQA13

HSU-15LQA13

HSU-10LQAB13

HSU-15LQAB13 HSU-09LQA03/R2(DB)

HSU-12LQA03/R2(DB) HSU-09LQA13/R2(DB)-WT HSU-09LQA13/R2(DB)-BK HSU-12LQA13/R2(DB)-WT

HSU-12LQA13/R2(DB)-BK HSU-12LEK03/R2(DB)

HSU-18LEK03/R2(DB) HSM24HEK03/R2(DB)

AS12GS1ERA

AS18GS1ERA

AS12GB2LAA HSU-10VEK03 HSU-13VEK03 HSU-18VEK03 HSU-24VEK03 AS05GA1LAA AS09GA1LAA AS12GB1LAA

AS18GD1LAA HSU-19CXAR3N HSU-19CXBW3N

HSU-09CK3W3N HSU-09LEK03-Y3 HSU-09CK6G2N HSU-12LEK03-Y3 HSU-09CK6B2N HSU-18LEK03-Y3 HSU-12CK3W3N HSU-24LEK03-Y2 HSU-12CKCS3N HSU-09LEK03/R2(DB) HSU-12CK6G2N HSU-24LEK03/R2(DB) HSU-12CK6B2N HSU-10LIN13 HSU-12CKAG3N HSU-09LTS14 HSU-12CKAB3N HSU-12LTS14 HSU-18CK3W3N HSU-18LTS14 HSU-18CK6B2N HSU-24LTS14 HSU-18CK6G2N HSU-07LEK03 HSU-18CKBS3N

HSU-15CKBS5N

HSU-18CKBS5N

HSU-18CKAB3N

HSU-18CKAG3N

HSU-15CKAG5N

HSU-18CKCS3N

HSU-24CK6B2N

HSU-13CXAS5N

HSU-13CXAS3N

HSU-13CXAR3N

HSU-13CXBW3N

HSU-19CXBW5N

HSU-24CXAS3N

HSU-19CXAS5N

HSU-19CXAS3N

Contents

PARTS AND FUNCTIONS									2
OPERATION						3
MAINTENANCE							6
CAUTIONS								7
TROUBLE SHOOTING										8

Please read this operation manual before using the air conditioner. Keep this operation manual for future reference.

0010564364

Parts and Functions

		Indoor Unit				Remote controller

	Inlet					Air Purifying
						Filter	Anion
	Inlet					generator
						(inside)
	grille
						Vertical blade
						(adjust left and
	Nano-Aquo					right air flow)
	Generator	Outlet		Horizontal flap
	inside			(adjust up and down air flow
				Don't adjust it manually)
	Display board
	Aureole				TEMP display
	Display mode the aureole display different
	colour when setting different function
	COOL: blue		FAN: yellow
	AUTO: white DRY: cyan			Nano-Aquo : green
			Inlet	Air Purifying Filter (inside)
	Inlet grille
	Outlet
	Horizontal flap		Vertical blade			Emergency
						Switch
	(adjust up and down air flow		(adjust left and		Display board
	Don't adjust it manually)		right air flow)
	Display board		1	2	3	4	5

1Signal receiver hole

2ON/OFF display

3Ambient temp.display

When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed.

4TIMER ON\OFF display TIMER ON-OFF display

SLEEP display

Note to the power failure resume: press the sleep button ten times in five seconds

and enter function after hearing four sounds.And press the sleep button ten times within five

seconds and leave this function after hearing two sounds.

5 COOL\HEAT\Dry\AUTO display

		1	Inlet	4 Air Purifying Filter (inside)
	2 Inlet grille					8
						Emergency
						Switch
	3	Outlet				9
	5	Anion generator	6 Vertical blade		12	10
						11
		(inside)	(adjust left and
	7	Horizontal flap				13
				right air flow)
	(adjust up and down air flow

Don't adjust it manually)

9 Power indicator (Lights up when unit starts.)

10 Timer mode indicator

(Lights up whenTimer operation is selected.)

11 Operation mode indicator

(lights up when the compressor is on.)

12 Remote signal receiver

(A beeping sound is generated when a signal from remote controller isreceived.)

13 Ambient temp display

When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference.

Actual inlet grille may vary from the one shown in the manual according to the product purchased

2

1			6	6. TIMER OFF display
2				TIMER ON display
			7	7. TEMP display
3				8. Additional functions display
4				Supplemented
				electrical
				Operation mode QUIET SLEEP heating HEALTH TURBO
5			8	Remote controller
				9. TURBO/QUIET button
9
10	TURBO/QUIET		18	10. FAN button
			19	11. COOL button
11				12. SWING LEFT/RIGHT button
			20
				13. FAN SPEED button
12
	SWING		21	14. HEALTH display
13				15. SLEEP display
14			22	16. LOCK button
	HEALTH	SLEEP		17. LIGHT button
15	ON	OFF	23	Control the lightening and extinguishing
	TIME	TIME
16			24	of the indoor LED display board.
				18. POWER/SOFT display
17			25
				19. DRY button
				20. TEMP display
				21.SWING UP/DOWNbutton
1. Mode display				22. TIMER OFF/ON displa
Operation mode	AUTO COOL DRY		FAN	23.HEALTH AIR FLOW button
Remote controller				24.CANCEL/CONFIRM button
2. Signal sending display				Function: Setting and cancel to the
3. SWING	display			timer and other additional functions.
4. FAN SPEED display				25. RESET button
			Display	When the remote controller appears
			circulated	abnormal, use a sharp pointed
LO MED		HI	AUTO	article to press this button to reset
5. LOCK display				the remote.

Healthy function is not available for some units.

Outdoor Unit

		OUTLET
		INLET
		CONNECTING PIPING
	4	AND ELECTRICAL WIRING
		4 DRAIN HOSE
Loading of the battery
1	Remove the battery cover;
2	Load the batteries as illustrated.
	2 R-03 batteries, resetting key
3	(cylinder);
	Be sure that the loading

4 is in line with the" + "/"-"; Note: Load the battery,then put on the cover again.

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or changeover

type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.

If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.

Operation

Base Operation

Remote controller	1
	TURBO/QUIET

2

3

SWING

4

3

2

HEALTH

TIME TIME

ON OFF

1. Unit start

Press ON/OFF on the remote controller, unit starts.

2.Select operation mode

COOL button:Cooling mode FAN button: Faning mode DRY button: Dehumidify mode

3.Select temp.setting

Press	/	button
	Every time the button is pressed, temp.setting
	increase 1oC,if kept depressed, it will increase
	rapidly
	Every time the button is pressed, temp.setting
	decrease 1oC,if kept depressed, it will
	decrease	rapidly

Select a desired temperature.

4.Fan speed selection

Press FAN button. For each press, fan speed changes as follows:

Remote controller:

Display circulated

LOW MED

HI

AUTO

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

	Operation	Remote	Note
	Mode	Controller
			Under the mode of auto operation, air conditioner will
	AUTO		automatically select Cool or Heat operation according to
			room temperature. When FAN is set to AUTO the air
			conditioner automatically adjusts the fan speed according
			to room temperature.
	COOL		according to room temperature.
	DRY		In DRY mode , when room temperature becomes lower
			than temp.setting+2o C, unit will run intermittently at LOW
			speed regardless of FAN setting.
			In FAN operation mode , the unit will not operate in COOL or
	FAN		HEAT mode but only in FAN mode, AUTO is not available in
			FAN mode. And temp. setting is disabled. In FAN mode,
			sleep operation is not available.

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:				Pi
Room	Designated	Timer	Fan	Operation
temperature	temperature	mode	speed	mode
Above 23oC	26oC	No	AUTO	COOL

It is impossible to change the settings of temp. and fan speed,It is also not possible to operate in timer or dry mode.

Test operation:

Test operation switch is the same as emergency switch.

Use this switch in the test operation when the room temperature is below 16oC, do not use it in the

normal operation.	Pi Pi

Continue to press the test operation

switch for more than 5 seconds . After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor unit will run in high speed.

Air Flow Direction Adjustment

1.Status display of air flow

Vertical flap

Pos.1

(Auto swing)

Initial state

Pos.2 No initial state disaplayed on remote controller, the vertical flap will be fixed on the current position

2.Left and right air flow adjustment

For each press of button, remote controller displays as follows :

remote controller:

Pos.1	Pos.2	Pos.3	Pos.4
Pos.5	Pos.6

Cautions:

When adjusting the flap by hand,turn off the unit.

When humidity is high,condensate water might occur adjusted to left or at air outlet if all vertical louvers are right.

It is advisable not to keep horizontal flap at downward

position for a long time in COOLor DRY mode , otherwise, condensate water might occur.

Note:

When restart after remote turning off, the remote controller controller will automatically memorize the previous set swing position.

3