Gemini TT-1100 USB, TT-1000 User Manual

0 (0)
Belt drive turntable
TT-1000
OPERATIONS MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
BEDIENUNGSHANDBUCH
FOR ENGLISH READERS Page 2 ~ Page 5
UTILISATEURS FRANCAIS Page 9 ~ Page 11
FÜR DEUTSCHE LESER Seite 12 ~ Seite 14
TT-1000
TT-1100USB
TT-1100USB
Belt drive turntable with USB
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interfer-
ence with electric appliances such as radios and televisions, use shielded cables and connectors for connections.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the liter-
ature accompanying the appliance.
The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the prod-
uct’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
READ INSTRUCTIONS: All the safety and operating instructions should be read before the product is operated.
RETAIN INSTRUCTIONS: The safety and operating instructions should be retained for future reference.
HEED WARNINGS: All warnings on the product and in the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS: All operating and use instructions should be followed.
CLEANING: The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since
they may corrode the cabinet.
ATTACHMENTS: Do not use attachments not recommended by the product manufacturer as they may cause hazards.
WATER AND MOISTURE: Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming
pool; and the like.
ACCESSORIES: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious dam-
age to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should fol-
low the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
CART: A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to over-
turn. See Figure A.
VENTILATION: Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these open-
ings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
POWER SOURCES: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company.
LOCATION: The appliance should be installed in a stable location.
NON-USE PERIODS: The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.
GROUNDING OR POLARIZATION:
• If this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the out-
let only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
• If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type
power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete out-
let. Do not defeat the safety purpose of the grounding type plug.
POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying par-
ticular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode. See Figure B.
LIGHTNING: For added protection for this product during a lightening storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due to lightening and power-line surges.
POWER LINES: An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
OVERLOADING: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric
shock.
OBJECT AND LIQUID ENTRY: Never push objects of any kind into this product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
SERVICING: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other haz-
ards. Refer all servicing to qualified service personnel.
DAMAGE REQUIRING SERVICE: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
• When the power-supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore th
e product to its normal operation.
• If the product has been dropped or damaged in any way.
• When the product exhibits a distinct change in performance, this indicates a need for service.
REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
SAFETY CHECK: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper op-
erating condition.
WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceiling.
HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
PLEASE READ BEFORE USING APPLIANCE
IMPORTANT WARNING AND SAFETY INSTRUCTIONS!
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT
OPEN!
Fig. A
Fig. B
2
TT-1000/TT-1100USB
3
TOP
BACK
NOTE: The TT line of Turntables has standard features that define the series. The TT-1100USB pictured on this page contains all of the same
characteristics as the TT-1000. The only exception is that the TT-1000 does not have a USB output or PHONO/LINE pre-amp.
NOTA: TT-1100USB mostrado. Ambos modelos tienen las mismas características excepto el TT-1000 tiene una salida USB y un pre-amplificador
de nivel de línea adicionales.
NOTE: Modèle présenté TT-1100 USB. Les deux appareils possèdent les mêmes caractéristiques à l’exception de la platine TT-1100 USB
qui comprend une sortie USB, ainsi qu’un niveau de sortie ligne.
WICHTIG: Die PLATTENSPIELER der TT-Serie verfugen uber die gleichen Standardfeatures. Der auf dieser Seite abgebildete TT-1100USB
unterscheidet sich vom TT-1000 nur durch seine Leistung. Die einzige Ausnahme ist die fehlende USB Audio Ausgang und PHONO/LINE
SCHALTER des TT-1000.
5
5
7
12
17
18
2
3
4
PANEL SUPERIOR
FACE SUPERIEURE
OBEN
PANEL TRASERO
FACE ARRIERE
HINTEN
14
1
9
10
8
14
13
6
11
15
16
Congratulations on purchasing the Gemini TT-1000/TT-1100USB high
torqe belt driven turntable. This unit is backed by a 1 year warranty*.
Prior to use, we suggest that you carefully read all the instructions.
TT-1000/TT-1100USB
- Fully manual belt drive turntable
- Battle and club style design
- +/-10% Variable pitch slider
- Solid aluminum platter
- Fully adjustable counter weight & anti-skating controls
- 33, 45 and 78 RPM, reverse playback capability
- Dual soft touch start/stop buttons
- Motor Off button for slower braking
- Removable target light (not included)
- Headshell and 45 adapter included
- CN-15 cartridge & felt slipmat included
- Detachable RCA & ground cables
TT-1100USB
- USB computer connectivity for PC and Mac
- Audacity recording software included
- Line level RCA outputs (with built–in pre–amp)
INTRODUCTION:
4
FEATURES:
CONNECTIONS:
1
MAIN POWER RECEPTACLE:
Connect the detachable linecord (included in the box
with your TT-1000/TT-1100USB) to the power receptacle, and
plug the other end of the linecord into an AC outlet.
The TT-1000/TT-1100USB has a universal power supply that can
accept any AC voltage from 100 VAC to 240 VAC. No need for
voltage select switches. It will work virtually anywhere in the world.
It is less susceptable to voltage sags or spikes than conventional
power supplies, providing greater electro magnetic isolation and
better protection against AC line noise
GROUNDING SCREW: You will need to ground the RCA cable(s)
by screwing in the grounding fork(s) to the GROUNDING SCREW
located on the rear panel of the mixer.
PHONO RCA OUTPUTS: This set of outputs carries the audio
signal from the turntable portion of the unit and should be
connected to an appropriate phono-level input on your audio mixer.
ALSO SEE ADDITIONAL TT-1100USB INFO SECTION BELOW.
2
3
TT-1000/TT-1100USB
ASSEMBLY & SETUP:
MOTOR DRIVE BELT
1. Start by placing the rubber DRIVE BELT around the inner bottom ring
of the turntable PLATTER. This should come preinstalled, but check
to make sure that it is not twisted or damaged.
2. Install the PLATTER on the center spindle and press it down firmly.
Check to make sure that it rotates uniformly and does not
wobble excessively.
3. Rotate the PLATTER so that one of the holes is aligned with the
Start Stop button on the front corner of the turntable. The brass
motor spindle should be visible through this hole.
4. Reach into the hole and pull the rubber DRIVE BELT off of the inner
ring, and install it over the motor spindle. Be careful not to twist the
rubber DRIVE BELT during this step. Check to make sure the PLATTER
rotates uniformly. If the DRIVE BELT is properly installed, there should
be a slight amount of tension that brings the PLATTER to a stop after
spinning it freely.
TURNTABLE INSTALLATION:
1. Make sure you have placed the platter securely on the spindle and
made sure that the MOTOR DRIVE BELT is in place.
2. Put the SLIPMAT on the PLATTER.
3. Set the TURNTABLE BASE on a flat, level surface free of
vibration. Use the turntable feet to stabilize the unit horizontally.
4. Try to place the unit as far away from the speakers as possible.
5. Keep the unit away from direct exposure to the sun, heat,
moisture or dirt.
6. Keep the unit well ventilated.
HEADSHELL INSTALLATION:
Insert the HEADSHELL into the front of the tubular TONE ARM.
While holding the HEADSHELL firmly in a horizontal position, turn
the LOCKING NUT counter clockwise until the HEADSHELL is
locked in place. Be sure not to over tighten the LOCKING NUT.
COUNTERWEIGHT INSTALLATION:
1. Slide the COUNTERWEIGHT onto the rear of the TONE ARM with the
numbered stylus gauge facing forward.
2. Twist the COUNTERWEIGHT counter clockwise lightly, to screw
it onto the rear of the TONE ARM.
ADJUSTING HORIZONTAL ZERO BALANCE AND STYLUS PRESSURE:
1. Without touching the stylus tip, remove the stylus protector (if your
cartridge has a detachable one.
2. Release the ARM CLAMP and lift the TONE ARM off the ARM REST.
3. Counter clockwise advancement of the
COUNTERWEIGHT will
cause the cartridge side of the TONE ARM to be lowered, turning
it clockwise will cause the opposite. Turn the COUNTERWEIGHT
clockwise or counter clockwise as needed until the TONE ARM is
balanced horizontally. You can easily tell this by watching for
the point where the TONE ARM "floats" freely.
4. Place TONE ARM on ARM REST and lock it in place
with the ARM CLAMP.
5. With the TONE ARM locked on the ARM REST, hold the
COUNTERWEIGHT steady with one hand while rotating the
STYLUS PRESSURE RING until the numeral "0" on the ring aligns with
the center line on the TONE ARM rear shaft. The
HORIZONTAL ZERO (0) balance should be completed.
6. Re-float the TONE ARM to ensure HORIZONTAL ZERO (0) balance.
If zero balance has not been maintained, repeat steps 3 - 5.
PRECAUTIONS:
1. All instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit. Please refer
all servicing needs to a Gemini-qualified service technician.
3. Do not expose this unit to direct sunlight or a heat source such as a ra-
diator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid solvents or
other cleaning detergents.
5. When moving this equipment it should be placed in its original carton
and packaging. This will reduce the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE SPRAY CLEANERS OR LUBRICANTS ON CON-
TROLS, SURFACES OR SWITCHES.
IN THE USA ~ IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT CALL GEMINI CUSTOMER SERVICE AT:
1 (732) 346-0061. DO NOT ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER.
FUNCTIONS:
12
POWER SWITCH: The POWER SWITCH turns the unit ON or
OFF. Make sure the switch is in the ‘OFF’ position prior to making
any connections.
START/STOP BUTTONS: These buttons start and stop the turntable
motor. Both buttons have the same function. If they seem to not be
functioning, check to make sure that the Motor Drive Belt is properly
installed in the SETUP INSTRUCTIONS.
MOTOR ON/OFF: This button allows you to start or stop the rotation
of the platter.
SPEED SELECTOR: Select the desired speed by depressing the 33, 45
or 78 (33 & 45 simultaneously) SPEED SELECTOR button.
REVERSE: Push the REVERSE button to play your track in reverse. Push
the REVERSE button again to cancel this feature.
45RPM RECORD ADAPTER
PITCH SLIDE CONTROL: The TT-1000/TT-1100USB is equipped with a
PITCH SLIDE CONTROL. When the PITCH SLIDE CONTROL is in the
center position, the speed will be 33, 45, or 78 depending on which
SPEED SELECTOR button is pushed. When the PITCH SLIDE CONTROL
is positioned off center, the pitch can vary ± 10% or ± 20% depend-
ing on which Pitch setting was selected and the position of the PITCH
SLIDE CONTROL.
TARGET LIGHT: Plug the TARGET LIGHT into the RCA STYLE JACK,
located adjacent to the PLATTER. Turn the POWER switch to the "ON"
position, at which point the TARGET LIGHT will light up.
COUNTERWEIGHT: Attach the COUNTERWEIGHT to the back of the
tonearm, with the number scale facing forwards, by turning the weight
counterclockwise.
ANTI-SKATE ADJUSTMENT: This knob is used to compensate for
inward tracking forces.
HEADSHELL/TONE ARM LIFT: Using the handle on the HEADSHELL to
carefully position the TONE ARM over the desired position on the
record. Lower the TONE ARM slowly, while letting go of the TONE
ARM over the record where you want to play. You may also use the
TONE ARM LIFT to raise and lower the TONE ARM.
ARM CLAMP: Release the ARM CLAMP found on the ARM REST
When play is over, raise the TONE ARM, move it onto the
ARM REST, and secure it with the ARM CLAMP.
SLIPMAT: Put the SLIPMAT
on the PLATTER.
13
14
15
16
17
18
5
TT-1000/TT-1100USB
8
9
10
11
6
7
4
5
ADDITIONAL TT-1100USB INFO
PHONO/LINE SWITCH: There is a switch on the back panel, next to
the RCA cables, that selects between PHONO/LINE. Use PHONO
level for plugging into a turntable input on a home stereo. Use the
LINE level for plugging into CD/AUX/TAPE inputs.
WARNING: You may damage your receiver if you plug
in a LINE level into a PHONO input.
USB Audio Output: Use the included USB Cable to connect your
turntable to your computer. The USB connection will provide audio
from the turntable and stereo input to your computer. You may wish
to install and use the AUDACITY software (PC and Mac), which al-
lows you to take advantage of advanced audio editing features,
such as audio normalization, noise removal and automatic track
separation.
White (L+)......................................Left Channel +
Blue (L-)............................................Left Channel -
Red (R+).......................................Right Channel +
Green (R-).....................................Right Channel -
SPECIFICATIONS:
CARTRIDGE INSTALLATION:
Connect the lead wires to the cartridge terminals.
For your convenience, the terminals of most car-
tridges are color-coded. Connect each lead wire to
the terminal of the same color. In case your car-
tridge is not marked the positive leads are the ones
on top negative below, left leads are the left chan-
nel, and right leads are the right channel.
TT-1000/TT-1100USB
TURNTABLE SECTION:
Type..................................................................Belt Drive Manual Turntable
Drive Method....................................................................................Belt Drive
Motor..................................................................................................DC Motor
Speed................................................................................33 1/3 or 45 RPM
Wow and Flutter..................................................Less than 0.25% WRMS*
*THIS RATING REFERS TO THE TURNTABLE ASSEMBLY AND PLATTER ONLY AND
EXCLUDES EFFECTS OF RECORDS, CARTRIDGES OR TONEARMS.
TONEARM SECTION:
Type...............................................Statically Balanced S-shaped Tonearm
Headshell Weight...................................................................................5.6 g
GENERAL:
Output (TT-1000)................................................................................PHONO
Power Supply.........................................AC 115 V~60 Hz/230 V~50 Hz
Power Consumption................................................................................5.5 W
Dimensions.................................................................17.67" x 14.56" x 5.7"
.....................................................................................(449 x 370 x 145 mm)
Weight........................................................................................8.1 lbs. (4 kg)
TT-1100USB
Computer interface..................................................USB 1.1/2.0 compliant
........................................................Windows XP or MAC OSX Compatible
Output...................................................................PHONO/LINE (RCA TYPE)
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
6
ATENCIÓN: Este producto cumple con la normativa legal si se utilizan cables y conectores blindados para conectar la unidad a otro equipo. Para evitar interferen-
cias electromagnéticas con otros aparatos eléctricos, como radios y televisores, deben emplearse cables y conectores blindados.
Los signos de exclamación dentro de un triángulo que puedan aparecer en la documentación que acompaña a la unidad pretenden alertar al usuario de instruc-
ciones de operación o mantenimiento importantes.
El signo de un rayo dentro de un triángulo pretende alertar al usuario de la presencia de "voltaje peligroso" no aislado en el inte-rior de la unidad, que podría ser
de suficiente intensidad como para constituir riesgo de descarga eléctrica.
LEA LAS INSTRUCCIONES: Deben leerse todas las indicaciones de uso y seguridad antes de usar este producto.
CONSERVE LAS INSTRUCCIONES: Las instrucciones de uso y seguridad deben conservarse para referencias futuras.
ATIENDA A LAS ADVERTENCIAS: Deben seguirse todas las advertencias sobre este producto que figuran en el manual de instrucciones.
SIGA LAS INSTRUCCIONES: Deben seguirse todas las instrucciones del manual.
LIMPIEZA: Este producto debe limpiarse con una mopa suave o con un paño seco. Nunca utilice cera para muebles, gasolina, insecticidas u otros líquidos
volátiles, ya que podrían corroer la carcasa.
COMPLEMENTOS: No utilice accesorios que no estén recomendados por el fabricante, pues podrían dañar la unidad.
AGUA Y HUMEDAD: No use este producto cerca de medios acuáticos, como una bañera, un cubo de agua, un fregadero o un
lavadero; tampoco en un sótano húmedo, ni cerca de una piscina o similar.
ACCESORIOS: No coloque el producto sobre un carrito, soporte, trípode, brazo o mesa. Podría caer y causar graves daños a un
niño o adulto, así como a la propia unidad. Úsese sólo con un carrito, soporte, trípode, brazo o mesa recomendado por el fabri-
cante. Al montar la unidad deben seguirse siempre las instrucciones y emplearse accesorios recomendados por el fabricante.
CARRITO: Si el producto va sobre un carrito, debe moverse el conjunto con cuidado. Detenciones bruscas, una fuerza excesiva o
superficies inadecuadas pueden provocar la caída de todo el conjunto. Véase Figura A.
VENTILACIÓN: Las aperturas y ranuras de la carcasa están diseñadas para la ventilación, aseguran un manejo fiable y lo protegen
de cualquier sobrecalentamiento, por tanto, nunca deben cubrirse ni bloquearse. Estas aperturas no deben taparse colocando el
producto sobre un sofá, una cama, una alfombra o superficies similares. Nunca debe colocarse en una estructura prefabricada, como una caja o un rack, a
menos que tengan la ventilación adecuada o lo permitan las instrucciones del fabricante.
FUENTES DE ALIMENTACIÓN: Esta unidad debe utilizarse exclusivamente con el tipo de suministro eléctrico indicado en la etiqueta correspondiente. Consúl-
telo antes de enchufar el producto si no está seguro del tipo de suministro del lugar donde lo va a usar.
UBICACIÓN: Este aparato debe colocarse en una ubicación estable.
PERIODOS SIN USARLO: Si no se va a usar la unidad durante un tiempo prolongado, desenchúfelo de la corriente eléctrica.
TOMA DE TIERRA O POLARIZACIÓN:
- Si este producto lleva una clavija de corriente alterna polarizada (con un pivote más grueso que otro, tipo inglés), sólo entrará en una posición. Es una medida
de seguridad. Si no puede introducir la cla-vija en el enchufe, gírela. En ningún caso debe forzarse. Si sigue sin entrar, un electricista debería cambiar el enchufe.
- Si la unidad lleva una clavija con tres pivotes (el tercero corres-ponde a la toma de tierra), sólo entrará en un tipo de enchufe. Se trata de una medida de se-
guridad. Si el enchufe y la clavija no son compatibles, un electricista deberá cambiar el enchufe. En ningún caso deberá forzarse.
PROTECCIÓN DEL CABLE DE CORRIENTE: Los cables de corriente deben protegerse para que nadie los pise ni corran el riesgo
de pinzarse por elementos colocados encima o que los aprisionen. Debe prestarse especial atención al cable, al enchufe, a los ex-
tensores de cable y al punto por donde el cable sale de la unidad.
TIERRA DE LA ANTENA EXTERIOR: Si el producto lleva conectada una antena exterior o sistema de cables, asegúrese de que
cuenta con la toma de tierra correspondiente, a fin de proteger la unidad de variaciones de voltaje y cargas de electricidad estática.
Existe documentación oficial acerca de la correcta utilización de la toma de tierra y de las medidas de seguridad pertinentes, conex-
ión de los electrodos de descarga y sus requisitos. Véase Figura B.
RAYOS: Como protección adicional del producto durante una tormenta eléctrica, o durante periodos prolongados sin usarlo, des-
enchúfelo de la corriente y desconecte la antena o sistema de cables. De este modo se protegerá el producto de los daños que
pueda producir la caída de un rayo o las fluctuaciones de la red eléctrica.
LÍNEAS ELÉCTRICAS: Nunca debe situarse un sistema de antena cerca de líneas eléctricas u otros circuitos de corriente. Tam-
poco debe colocarse en lugares donde pueda caer sobre dichos circuitos eléctricos. Al instalar un sistema de antenización exterior, debe tomarse la extrema
precaución de no tocar dichas líneas eléctricas, pues el mas minimo contacto puede ser fatal.
SOBRECARGA: No sobrecargue los enchufes de la pared con ladrones o instalando enchufes múltiples, pues correría el riesgo de electrocución o incendio.
ENTRADA DE OBJETOS O LÍQUIDOS: Nunca introduzca objetos de ningún tipo en el interior del producto, pues podrían tocar una parte eléctrica y cortocir-
cuitar el aparato, lo que resultaría en un incendio o descarga eléctrica. No verter nunca ningún líquido sobre el producto.
REPARACIÓN: No intente reparar el producto por cuenta propia, ya que abrir o retirar la carcasa le expondría a un voltaje peligroso u otros peligros. Diríjase
siempre a un centro de servicio técnico autorizado.
DAÑOS QUE REQUIEREN REPARACIÓN: Desenchufe el aparato de la corriente y diríjase a un servicio técnico autorizado si se da alguna de las siguientes
situaciones:
- El cable de alimentación o la clavija están dañados.
- Se ha vertido líquido o ha caído algún objeto sobre la unidad.
- El aparato se ha expuesto a la lluvia o a salpicaduras.
- La unidad se ha caído al suelo o dañado de algún modo.
- El aparato no funciona con normalidad, ni aun siguiendo las instrucciones. Ajuste sólo los mandos que se indican en las instrucciones, ja que la manipulación
inadecuada de otros controles podría dañar la unidad y requeriría un mayor trabajo de un técnico para restablecer su funcionamiento normal.
- Si el producto muestra anomalías en su funcionamiento, necesita revisión por parte de un servicio técnico autorizado.
RECAMBIOS: Cuando se necesite alguna pieza de recambio, asegúrese de que el servicio técnico utilice piezas originales autori-zadas o que tengan las mismas
características que las originales. Los reemplazos no autorizados pueden causar descargas eléctricas, incendios u otros daños.
COMPROBACIÓN DE SEGURIDAD: Tras la reparación, solicite al técnico que efectúe las comprobaciones de seguridad necesarias para determinar que el pro-
ducto se encuentra en las condiciones adecuadas para su funcionamiento.
MONTAJE EN UNA PARED O TECHO: Este producto nunca debe montarse en una pared o en el techo.
CALOR: Este producto debe alejarse de fuentes de calor, como radiadores, estufas u otros aparatos que irradien calor, incluyendo amplificadores.
POR FAVOR LEA ANTES DE UTILIZAR,
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Fig. B
Fig. A
PRECAUCIÓN
RIESGO DE SHOCK
ELECTRICO - NO
ABRIR!
Loading...
+ 11 hidden pages