GE ZBD6700, ZBD6600, ZBD6905, ZBD6900, ZBD7005 User Manual

...
0 (0)

Installation

Instructions

If you have questions, call 800.626.2000 or visit our website at: www.monogram.com

Built-In Dishwashers

ZBD6400, ZBD6500, ZBD6600

ZBD6700, ZBD6900, ZBD7000,

ZBD7100

Chef’s Washers

ZBD6605, ZBD6905, ZBD7005,

ZBD7105

Design Guide with

Installation Instructions

Monogram.®

We bring good things to life.

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT - Save these instructions for local inspector’s use. Observe all governing

codes and ordinances.

Note to Installer - Be sure to leave these instructions with the Consumer.

Note to Consumer - Keep these instructions with your Owner’s Manual for future reference.

Skill Level – Installation of this dishwasher requires basic mechanical and electrical skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty.

Completion Time – 1 to 2 Hours. New installations require more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

FOR YOUR SAFETY

Read and observe all CAUTION and WARNINGS shown throughout these instructions.

For Monogram local service in your area, 1-800-444-1845.

For Monogram service in Canada 1-888-880-3030

For Monogram Parts and Accessories, call 1-800-626-2002.

CONTENTS

Design Information

 

Installation Instructions

 

Product Dimensions .......................................................

3

Step 1, Remove Packaging ...........................................

10

Models Available ............................................................

3

Step 2, Install Leveling Legs .......................................

10

Advance Planning ..........................................................

3

Step 3, Remove Access Covers ....................................

10

Installation Preparation

 

Step 4, Install 90° Elbow ...............................................

10

Materials You Will Need .................................................

4

Step 5, Install Power Cord............................................

11

Tools You Will Need .......................................................

4

Step 6, Level Dishwasher ..............................................

11

Parts Supplied .................................................................

5

Step 7, Slide Dishwasher into Opening.......................

11

Prepare Dishwasher Enclosure .....................................

5

Step 8, Connect Water Line ........................................

11

Drain Requirements .......................................................

6

Step 9, Connect Drain Line ........................................

12

Prepare Electrical Wiring ...............................................

7

Step 10, Connect Electrical .........................................

12

Prepare Hot Water Line .................................................

8

Step 11, Position and Level Dishwasher ......................

13

Custom Panel Dimensions

 

Step 12, Pre-Test Check List ........................................

13

Custom Panels for ZBD6400 .........................................

9

Step 13, Dishwasher Wet Test .....................................

13

Custom Panels for ZBD7000, ZBD7005 ........................

9

Step 14, Secure Dishwasher

 

 

 

to Cabinet or Countertop .......................................

14

 

 

Step 15, Install Toekick, Custom Toekick ..................

14

 

 

Step 16, Install Side Trim Strips ..................................

14

 

 

Panel Installation for Models

 

 

 

ZBD7000 and ZBD7005 ............................................

15

2

Design Information

PRODUCT DIMENSIONS

 

 

34"

 

 

Adjustable

 

 

to 35"

 

 

*Dishwasher model

 

 

ZBD7000 and

 

 

Chef’s Washer

 

 

model ZBD7005

*24"

 

require a 3/4" thick

23-7/8"

custom panel and

 

will be 24-3/4"

 

 

deep.

DISHWASHER MODELS

Traditional Built-In

ZBD6400 BB, Black - Accepts 1/4" or 3/4" custom panels

ZBD6400 WW White - Accepts 1/4" or 3/4" custom panels

Trim Kits for models ZBD6400

ZPF625W (white) or ZPF625B (black) custom panel kits, supports a 1/4" thick custom door panel.

ZPF675W (white) or ZPF675B (black) custom panel kits support a 3/4" thick custom door panel.

Traditional Built-In

ZBD6500 SS, Stainless steel door

Professional Series

ZBD6600 SS, Stainless Steel

Fully Wrapped

ZBD6700 BB, Black

ZBD6700 WW, White

ZBD6900 SS, Stainless steel with black controls

Fully Integrated

ZBD7000 II, Requires custom panel and handle ZBD7100 SS, Stainless steel with tubular handle

CHEF’S WASHER MODELS

Professional Series

ZBD6605 SS, Stainless steel

Fully Wrapped

ZBD6905 SS, Stainless steel

Fully Integrated

ZBD7005 II, Requires custom panel and handle ZBD7105 SS, Stainless steel with tubular handle

ADVANCE PLANNING

These dishwashers are designed for versatility, adaptable to virtually any installation.

All models have a full length door or a modified door to accept a full cabinet panel without the traditional access panel

Side tub flange trim is adjustable and will conceal any slight gap between the dishwasher and adjacent cabinetry.

These dishwashers may be installed beneath countertops of stone or other materials that will not accept screws. No trim kit required.

Standard installation in 24" deep cabinets

In standard 24" deep cabinets, the dishwasher door will be flush with adjacent cabinetry.

Models with 3/4" thick custom door panel will fit flush with adjacent cabinetry.

Supplied or Custom Toekicks

A 2-piece toekick is supplied with all models. The toekick is height and depth adjustable.

Depending on cabinetry style, a custom toekick can also be installed to match cabinetry. Care must be taken to assure door swing clearance above the toekick.

A notched continuous toekick may be necessary to allow a long door panel, on models ZBD7000 and ZBD7005, to swing back and under the dishwasher.

ADA-Compliant

Installation below 34" high countertops

A reduced height installation (32-1/2" min.) beneath a 34" countertop, can be accomplished by removing the front leveling legs. The rear legs should be screwed in flush with the bottom support, as shipped. The front of the dishwasher must be shimmed to level the dishwasher. Water and electrical must be routed through the back wall.

All models are ADA-Compliant. Models ZBD7000 and ZBD7005 offer even more installation and design flexibility because the required custom door panel may be sized from 26-1/4 to 30-1/4" height. See page 9 for details.

3

GE ZBD6700, ZBD6600, ZBD6905, ZBD6900, ZBD7005 User Manual

Installation Preparation

MATERIALS YOU WILL NEED:

Materials Required for All Installations

♦ 90° Elbow (3/8”NPT external thread on one end, opposite end sized to fit water supply)

Note: Use new ferrule. Do not use old parts.

Strain relief for electrical connection

Thread seal tape

UL Listed wire connectors (3)

Screw type hose clamps

Screw Type Clamps

90° Elbow

Wire Nuts

Strain Relief

Thread Seal

Tape

Materials For New Installations Only:

♦ Air gap for drain hose, if required

♦ Waste tee for house plumbing, if applicable

 

 

♦ Electrical cable or power cord, if applicable

Shut-Off

Electrical Cable

Waste Tee

Valve

or Power Cord

♦ Hand shut-off valve (recommended)

 

♦ Water line 3/8” min. copper or 1/2” min. plastic (plastic

 

 

must be tested for temperature and pressure)

 

 

♦ Coupler for extending drain line, if applicable

 

 

Air

Coupler

 

 

 

Gap

 

Hot Water Line

TOOLS YOU WILL NEED:

Flat Blade Screwdriver

Tools Required for All Installations

Phillips head and flat blade screwdrivers

3/8”, 5/16” and 1/4” nutdrivers

♦ Level

 

Safety Glasses

 

 

♦ Carpenters square

 

 

♦ Measuring tape

 

 

♦ Safety glasses

Wire Strippers

 

♦ Flashlight

Adjustable

 

♦ Bucket to catch water when flushing the line

Wrench

Bucket

Tubing cutter

Gloves to protect against sharp edges

Wire strippers

For New Installations Only:

Measuring Tape

♦ Drill and appropriate bits ♦ Hole saw set

Level

 

Nut Driver

Phillips

Head

Screwdriver

 

Tubing

 

Cutter

Flashlight

 

Drill

 

and Bits

 

Square

 

Hole

 

Saw Set

Gloves

4

20-1/2"
Countertop
Dishwasher

 

Installation Preparation

 

PARTS SUPPLIED:

 

 

 

Remove the hardware accessory bag and other parts

 

 

from inside or taped to the outside of the dishwasher.

 

 

Check contents against illustrations to insure that all

 

Template

parts are included.

 

 

for

 

 

 

ZBD7000

♦ 2-piece toekick

 

 

ZBD7005

 

 

Only

♦ 6 screws (see illustration)

 

 

 

♦ 2 leveling legs

Junction

 

 

♦ Template for the installation of a

Box Cover

 

 

with screws

2 Leveling Legs

 

 

Template with Mounting Hardware

custom panel packed with models

 

ZBD7000 and ZBD7005 only

 

 

 

♦ Junction box cover

 

 

 

Screws A

Screws B

Screws C

Insulation

 

(2) Countertop

(2) Cabinet

(2) Color

 

Mounting

Mounting

Matched

2-Piece Toekick with

Screws

Screws

Toekick

Sound Insulation

 

 

Screws

 

 

 

PREPARE DISHWASHER ENCLOSURE

 

This Wall Area

 

 

must be Free of

 

34" to 35"

Pipes or Wires

24"

1-3/4"

Underside

Min.

of Countertop

 

 

to Floor

 

 

 

 

6"

 

23-7/8" Min.

 

 

24-1/4" Max

 

*Models ZBD7000 and ZBD7005 with custom panels are 24-3/4" deep

The rough cabinet opening must be at least 24” deep, 23-7/8”min. to 24-1/4” wide. The height should be 34” min. and 35” max.

Note: ADA installation, beneath 34" high countertops may be accomplished by removing front leveling legs. Drain hose, water and electrical must be routed through the cutout on the back of the dishwasher.

The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage.

The dishwasher must be fully enclosed on the top, sides and back, but should not support any part of the enclosure.

The floor inside the opening must be even and level with the finished floor of the kitchen. If the kitchen floor is tile, it may be

higher than the floor of the installation cutout. Pieces of wood may be placed into the cutout floor to make it level or higher than the room

floor. This will allow easy removal for any future service.

Corner Installation

When installing into a corner, allow 2" min. clearance between dishwasher and adjacent cabinet or wall.

Allow 24-1/8" min. clearance from the front of the dishwasher for door opening.

24-1/8"

Clearance for Door Opening 2" Minimum

5

Loading...
+ 11 hidden pages