GE PFDN440, PFMN445, PFDS450, PFMS455, PFDS455 User Manual 2

...
0 (0)

DryersProfile

Printed in Mexico

GEAppliances.com

Safety Instructions . . . . . . . . . . . 2–4

Operating Instructions

Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8

Cycle Options . . . . . . . . . . . . . . . . . . . . 9, 10

Smart Appliance . . . . . . . . . . . . . . . . . . . .13

Dryer Features . . . . . . . . . . . . . . . . . .10, 11

Quick Start Guide . . . . . . . . . . . . . . . . . . . .5

Settings Option. . . . . . . . . . . . . . . . . . . . . .10

Using the Dryer . . . . . . . . . . . . . . . . . . . . .11

Installation Instructions

Before You Begin. . . . . . . . . . . . . . . .14, 15 Connecting the Inlet Hoses . . . . . . . . .17 Connecting a Gas Dryer. . . . . . . . .18–21 Connecting an

Electric Dryer. . . . . . . . . . . . . . . . . . . .22–24 Exhausting the Dryer. . . . . . . . . . . .25–31 Final Setup . . . . . . . . . . . . . . . . . . . . . . . . . .32 Installing the Pedestal. . . . . . . . . . .43–45 Location of your Dryer . . . . . . . . . .15, 16 Reversing the Door Swing. . . . . . .33–39 Stacking the Washer

and Dryer . . . . . . . . . . . . . . . . . . . . . . .40–42

Troubleshooting Tips. . . . . . .46–49

Consumer Support

Consumer Support. . . . . . . . Back Cover

Warranty (Canada). . . . . . . . . . . . . . . . . 51

Warranty (U.S.) . . . . . . . . . . . . . . . . . . . . . 50

Owner’s Manual &

Installation Instructions

PFDS450

PFDS455

PFDN440

PFDN445

PFMS450

PFMS455

PFMN440

PFMN445

Sécheuses

Profile

Manuel d’utilisation et d’installation

La section française commence à la page 52

Secadoras

Profile

Manual del propietario e instalación

La sección en español empieza en la página 104

SAVE THESE INSTRUCTIONS

Write the model and serial numbers here:

Model # ______________

Serial # _______________

They are on the label on the front of the dryer behind the door.

234D2010P001

49-90472 03-13 GE

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

2

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other

Installation and service must be

flammable vapors and liquids in the

performed by a qualified installer,

vicinity of this or any other appliance.

service agency or the gas supplier.

WHAT TO DO IF YOU SMELL GAS:

1

2

3

Do not try to light a match, or cigarette, or turn on any gas or electrical appliance.

Do not touch any electrical switch; do not use any phone in your building.

Clear the room, building or area of all occupants.

4

5

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.

If you cannot reach your gas supplier, call the fire department.

California Safe Drinking Water and Toxic Enforcement Act

This act requires the governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

PROPER INSTALLATION

This dryer must be properly installed and located in accordance with the Installation Instructions before it is used. Installation Instructions are included in the back of this manual.

Properly ground dryer to conform with all governing codes and ordinances. Follow details in Installation Instructions.

Install or store where it will not be exposed to temperatures below freezing or exposed to water or weather.

Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.

Remove all sharp packing items and dispose of all shipping materials properly.

Exhaust/Ducting

1

Dryers MUST be exhausted to the outside to prevent

large amounts of moisture and lint from being blown

 

 

into the room.

2

Use only rigid metal 4” diameter ductwork inside the

dryer cabinet. Use only UL approved rigid metal or

 

 

flexible metal 4-in diameter ductwork for exhausting

 

to the outdoors. Never use plastic or other

 

combustible, easy-to-puncture ductwork. USE OF

 

PLASTIC OR OTHER COMBUSTIBLE DUCTWORK CAN

 

CAUSE A FIRE. PUNCTURED DUCTWORK CAN CAUSE

 

A FIRE IF IT COLLAPSES OR BECOMES OTHERWISE

 

RESTRICTED IN USE OR DURING INSTALLATION.

For complete details, follow the Installation Instructions.

IMPORTANT SAFETY INFORMATION.

 

READ ALL INSTRUCTIONS BEFORE USING.

GEAppliances.com

WARNING!

YOUR LAUNDRY AREA

Keep the area underneath and around your appliances free of combustible materials, (lint, paper, rags, etc.), gasoline, chemicals and other flammable vapors and liquids.

Keep the floor around your appliances clean and dry to reduce the possibility of slipping.

Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with or inside this or any other appliance.

Keep the area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt.

Keep all laundry aids (such as detergents, bleaches, etc.) out of the reach of children, preferably in a locked cabinet. Observe all warnings on container labels to avoid injury.

Never climb on or stand on the dryer top.

WHEN USING YOUR DRYER

Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped.

Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT

OPERATE THE DRYER WITHOUT THE LINT FILTER IN PLACE.

Do not wash or dry articles that have been cleaned in, washed in, soaked in or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). These substances give off vapors that may ignite or explode. Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation.

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a clothes load to catch fire.

Any article on which you have used a cleaning solvent or that contains flammable materials (such as cleaning cloths, mops, towels used in beauty salons, restaurants or barber shops, etc.) must not be placed in or near the dryer until solvents or flammable materials have been removed. There are many highly flammable items used in homes such as acetone, denatured alcohol, gasoline, kerosene, some household cleaners, some spot removers, turpentines, waxes, wax removers and products containing petroleum distillates.

The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s care instructions.

Do not dry articles containing rubber, plastic or similar materials such as padded bras, tennis shoes, galoshes, bath mats, rugs, bibs, baby pants, plastic bags, pillows, etc. that may melt or burn. Some rubber materials, when heated, can under certain circumstances produce fire by spontaneous combustion.

Do not store plastic, paper or clothing that may burn or melt on top of the dryer during operation.

Garments labeled Dry Away from Heat or Do Not Tumble Dry (such as life jackets containing Kapok) must not be put in your dryer.

Do not dry fiberglass articles in your dryer. Skin irritation could result from the remaining particles that may be picked up by clothing during subsequent dryer uses.

To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning (except the removal and cleaning of the lint filter).

NOTE: Pressing START/PAUSE or POWER does NOT disconnect the appliance from the power supply.

If you see water on the floor around the dryer, call for service.

Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against the front or back of the dryer.

3

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

WHEN USING YOUR DRYER (cont.)

Neverattempttooperatethisapplianceifitisdamaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician. See the Sorting and Loading Hints section on page 12.

If yours is a gas dryer, it is equipped with an

automatic electric ignition and does not have a pilot light. DO NOT ATTEMPT TO LIGHT WITH A MATCH. Burns may result from having your hand in the vicinity of the burner when the automatic ignition turns on.

Do not open the dryer door during steam cycles. The steam is very hot and it will continue to exhaust from the port for several seconds after opening. Do not touch the steam port after a steam cycle.

Do not use a steam cycle with items such as wool, leather, silk, lingerie, foam products or electric blankets.

Do not use steam cycles on new clothes without first washing.

You may wish to soften your laundered fabrics or reduce the static electricity in them by using a dryerapplied fabric softener or an anti-static conditioner. We recommend you use either a fabric softener in the wash cycle, according to the manufacturer’s instructions for those products, or try a dryer-added product for which the manufacturer gives written assurance on the package that their product can be safely used in your dryer. Service or performance problems caused by use of these products are the responsibility of the manufacturers of those products and are not covered under the warranty of this appliance.

Never attempt to use the Steam Dewrinkle or Steam Refresh cycles without clothes in the drum. Additionally, it is highly recommended to select the appropriate load size for best results. Selecting large load cycles for small loads may result in wetting of clothes, and selecting small load cycles for large loads may result in poor dewrinkling performance.

Do not spray any type of aerosol into, on, or near dryer at any trime. Do not use any type of spray cleaner when cleaning dryer interior. Hazardous fumes or electrical shock could occur.

WHEN NOT USING YOUR DRYER

Grasp the plug firmly when disconnecting this appliance to avoid damage to the cord while pulling. Place the cord away from traffic areas so it will not be stepped on, tripped over or subjected to damage.

Do not attempt to repair or replace any part of this appliance or attempt any servicing unless specifically recommended in this Owner’s Manual or in published user-repair instructions that you understand and have the skills to carry out.

Before discarding a dryer, or removing it from service, remove the dryer door to prevent children from hiding inside.

Do not tamper with controls.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

About the dryer control panel.

GEAppliances.com

WARNING! To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

Throughout this manual, features and appearance may vary from your model.

Quick Start

If the screen is dark, press the POWER button to “wake up” the display.

1 Press the POWER button.

 

 

SENSOR DRY

COTTONS

 

Select a cycle by turning the

NORMAL /

 

WRINKLE FREE

STEAMREFRESH

2

 

MIXED LOADS

Cycle Knob.

ACTIVE WEAR

CYCLES

 

 

SPECIALTY

DELICATES

SPEED DRY

TIME DRY

WARM UP

STEAM

DEWRINKLE

TIMED DRY

 

3 If you selected a SENSOR CYCLE – just press the START/PAUSE button.

Models: PFDS450 / PFDS455 / PFMS450 / PFMS455

 

SENSOR DRY

COTTONS

 

NORMAL /

 

MIXED LOADS

 

 

WRINKLE FREE

 

2

ACTIVE WEAR

 

DELICATES

 

SPEED DRY

TIME DRY

POWER WARM UP

TIMED DRY

9

STEAMREFRESH

SPECIALTY

CYCLES

STEAM

DEWRINKLE

 

1

3

6

Models: PFDN440 / PFDN445 / PFMN440 / PFMN445

9

 

 

NORMAL /

 

 

 

 

 

MIXED LOADS

 

SENSOR DRY WRINKLE FREE

COTTONS

 

ACTIVE WEAR

 

2

DELICATES

 

SPECIALTY

 

 

 

 

 

CYCLES

 

SPEED DRY

 

 

 

TIME DRY

 

 

 

AIR FLUFF

 

 

NO HEAT

 

 

 

POWER

WARM UP

TIMED DRY

 

 

DEWRINKLE

 

If you selected a TIME DRY CYCLE -select your heat setting and the amount of time you want your items to dry by using the cursor buttons. Then press the START/PAUSE button.

EXTRA DRY

MORE DRY

DRY

LESS DRY

DAMP

ANTI -

BACTERIAL

HIGH

MEDIUM

LOW

EXTRA LOW

8

e

DELAY

DRYER

 

4

 

DRY

START

RACK

EXTRA DRY

 

 

 

 

 

 

 

 

 

 

MORE DRY

 

 

 

 

 

DRY

SENSOR

 

 

 

 

DRY

 

 

 

 

 

 

 

 

BACK

LESS DRY

 

 

ENTER

 

DAMP

 

 

 

 

 

 

 

 

 

ANTI -

 

 

 

 

 

BACTERIAL

 

 

 

 

 

HIGH

 

DRUM

MY

 

 

MEDIUM

DRY

EXTENDED

DAMP

TEMP

LIGHT

CYCLE

 

 

SETTINGS STORE MY CYCLE

TUMBLE

ALERT

LOW

 

 

 

 

 

EXTRA LOW

 

PRESS & HOLD 3 seconds for secondary OPTIONS

LOCK

 

 

 

 

 

 

 

 

 

 

Push to Lock Control

 

 

 

 

 

Hold 3 Secs to Unlock

 

 

7

 

 

 

 

5

8

e

DELAY

DRYER

 

4

 

 

 

DRY

START

RACK

EXTRA DRY

 

 

 

 

 

 

 

 

 

 

MORE DRY

 

 

 

 

 

DRY

SENSOR

 

 

 

 

DRY

 

 

 

 

 

 

 

 

BACK

LESS DRY

 

 

ENTER

 

DAMP

 

 

 

 

 

 

 

 

 

ANTI -

 

 

 

 

 

BACTERIAL

 

 

 

 

 

HIGH

 

DRUM

MY

 

 

MEDIUM

DRY

EXTENDED

DAMP

TEMP

LIGHT

CYCLE

 

 

SETTINGS STORE MY CYCLE

TUMBLE

ALERT

LOW

 

 

 

 

 

EXTRA LOW

 

PRESS & HOLD 3 seconds for secondary OPTIONS

LOCK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Push to Lock Control

 

 

 

 

 

 

 

 

 

 

 

Hold 3 Secs to Unlock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

3

 

6

 

 

 

5

1

 

 

7

 

Power

 

 

 

 

 

 

 

 

 

 

Press to “wake up” the display. If the display is active, press to turn the dryer off.

 

NOTE: Pressing POWER does not disconnect the appliance from the power supply.

SENSOR

DRY

DRY

TEMP

5

About the dryer control panel.

Dry Cycles

The dry cycle controls the cycle time for the drying process. The chart below will help you match the dry setting with the loads.

2 Sensor Cycles

COTTONS For cottons and most linens.

NORMAL/ For loads consisting of cottons and poly-blends.

MIXED LOAD

WRINKLE FREE For wrinkle-free/easy care and permanent press items.

ACTIVE WEAR Clothing worn for active sports exercise and some casual wear. Fabrics include new technology finishes and stretch fibers such as Spandex.

DELICATES For lingerie and special-care fabrics.

SPEED DRY For small loads that are needed in a hurry, such as sports or school uniforms. Can also be used if the previous cycle left some items damp, such as collars or waistbands.

Timed Dry Cycles

STEAM

For slightly wrinkled dry garments. Significantly reduces wrinkles on 1–5 garments.

REFRESH

Selecting a higher number of garments for the cycle (e.g., selecting 5-garment load for a 1-garment load) may result in excessive wetting

(on some models)

of clothes. After the STEAM REFRESH Cycle, the unit will beep and display “Garments Ready” and “0:00.” If the unit is not turned off or if the

 

door is not opened, the dryer will continue to tumble for 30 minutes. At the end of 30 minutes, it will display “0:00” and “Cycle Complete.”

 

NOTE: When STEAM REFRESH is selected, “EXTENDED TUMBLE” will automatically turn on and cannot be turned off.

 

A single extremely light fabric item may need to have an additional item included in the steam refresh cycle to achieve optimum results.

 

 

DEWRINKLE

For removing wrinkles from items that are dry or slightly damp. This cycle is not reccomended for delicate

(on some models)

fabrics.

 

 

STEAM

For use with larger loads than STEAM REFRESH. Ideal for loads left in dryer for an extended

DEWRINKLE

time. Selecting a larger cycle than needed (e.g., selecting Large Load for a half-full dryer)

(on some models)

may result in excessive wetting of clothes.

 

 

WARM UP

Provides 10 minutes of warming time to warm up clothes.

 

 

My Cycle (on some models)

MY CYCLE Press to use, create or modify custom dry cycles.

3 Timed Dry

Use to set your own dry time. TIMED DRY is also recommended for small loads.

To use TIMED DRY:

1.Turn dry cycle dial to TIMED DRY.

2.Select the drying time by pressing the Sand Tbuttons. You can increase the time in 10-minute increments up to 2 hours, 5 minutes.

3.Select the DRY TEMP.

4.Close the door.

5.Press START/PAUSE.

4 Sensor Dry

The sensor continuously monitors the amount of moisture in the load. When the moisture in your clothes reaches your selected dry level, the dryer will stop.

EXTRA DRY Use for heavy-duty fabrics or items that should be very dry, such as towels.

MORE DRY Use for heavy or mixed type of fabrics.

DRY Use for normal dryness level suitable for most loads. This is the preferred cycle for energy saving.

LESS DRY Use for lighter fabric (ideal for ironing).

DAMP For leaving items partially damp.

6

GEAppliances.com

5 Dry Temp

You can change the temperature of your dry cycle.

ANTI-BACTERIAL This option may only be used with COTTONS or MIXED LOAD cycles. This option reduces certain types of bacteria by 99.9%, including: Staphylococcus aureus, Pseudomonas aeruginosa and Klebsiella pneumoniae*. The anti-bacterial process occurs when high heat is used during a portion of this drying cycle.

NOTE: Do not use this cycle on delicate fabrics.

*The Anti-Bacterial Cycle is Certified by NSF International (formerly National Sanitation Foundation) to NSF Protocol P154 Sanitization Performance of Residential Clothes Dryers.

HIGH For regular to heavy cottons.

MEDIUM For synthetics, blends and items labeled permanent press.

LOW For delicates, synthetics and items labeled Tumble Dry Low.

EXTRA LOW For lingerie and special-care fabrics.

6 START/PAUSE

Press to start a dry cycle. If the dryer is running, press it once and it will pause the dryer. Press it again to resume the dry cycle.

7 MY

YCLE

C

STORE MY CYCLE

My Cycle (on some models)

Set up your favorite combination of settings and save them here for one touch recall. These custom settings can be set while a cycle is in progress.

To store a MY CYCLE combination of settings:

1. Select your drying cycle.

2.Change DRY TEMP and SENSOR DRY settings to fit your needs.

3.Select any drying OPTIONS you want.

4.Press and hold the MY CYCLE button for 3 seconds to store your selection. A beep will sound the button will light up, and the unit will display “My cycle is now programed with the current cycle settings”.

To recall your stored MY CYCLE combination:

Press the MY CYCLE button before drying a load. The light in the center of the button will light up when MY CYCLE is selected.

To change your stored MY CYCLE combination:

Follow Steps 1–4 in “To store a MY CYCLE combination of settings.”

8 Display

Special Cycle Status OR

Est. Cycle Time

Dryer Rack OR Timed Dry

OR Time to Dry

 

 

 

SPECIALTY CYCLE 0 1:10

SPECIALTY

Comforters

 

Delay Time

1:00

CYCLES

 

Clean Lint Filter

Delay Time

Lint Filter Status

Status

 

Screen

“CLEAN LINT FILTER” (message)

This message appears periodically. It is only a reminder.

ENTER

DELAY TIME

After the POWER button is pressed, the CLEAN LINT FILTER message could appear if the previous cycle was not finished. This message will disappear after the START button is pressed. Even though you have already cleaned the filter (before the POWER button was pressed), the CLEAN LINT FILTER message will still be displayed until the START button is activated.

7

About the dryer control panel.

9

Specialty Cycles

 

1.

Turn the CYCLE knob to SPECIALTY CYCLES. A list of cycle options will appear in the display.

 

2.

Using the cursor buttons, select a CATEGORY.

 

3.

Using the cursor buttons, select a CYCLE.

 

 

Press the BACK button to take you back to the CATEGORIES.

 

4. Press ENTER to select.

 

5.

Press the START/PAUSE button.

SPECIALTY CYCLES include:

Garment

Coats

Hosiery/Bras (use mesh bag)

Jeans

Khakis

Bed and Bath

Blankets (Cotton)

Comforters

Sheets

Towels

Specialty Cycles

Air Fluff

Dryel

Fleece

Fragile Cottons

Performance Fabrics

Pet Bedding

Play Clothes

Rack Dry

Sleeping Bag

Throw Rugs

Washer Communicated Cycles

To turn on communication, press the SETTINGS button on the washer control panel. When “DRYER LINK” appears in the display, press ENTER. Using the arrow keys, select ON; then press ENTER.

When the washer cycle is completed, the washer will communicate with the dryer when any button on the control panel is touched or the door is opened.

The washer will display, “TRANSFERRING CYCLE INFORMATION TO THE DRYER” and the dryer will display, “RECEIVING CYCLE INFORMATION TO THE DRYER”.

The dryer will only communicate with the washer if the dryer is not running a cycle.

If the washer starts a new cycle before the dryer has a chance to communicate with it, the information will be lost.

8

About cycle options.

NOTE: Not all features are available on all dryer models. GEAppliances.com

EXTENDED

Extended Tumble

 

TUMBLE

Minimizes wrinkles by adding approximately 60

ExtendedTumbleisautomaticallyselectedforthe

minutes of no-heat tumbling after clothes are

SteamRefresh cycle and cannot be deselected.

 

dry.

Dryer will beep and display “Garments Ready”

 

The light in center of the button will light up

when SteamRefresh is complete. The dryer will

 

continue in Extended Tumble until the door is

 

when EXTENDED TUMBLE is on.

 

opened.

 

 

DAMP

ALERT

Damp Alert

This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish to hang dry. The DAMP ALERT will only beep when this option is selected.

Removing clothes and hanging them when they are damp can reduce the need to iron some items.

The light in center of the button will light up when DAMP ALERT is on.

DRUM

LIGHT

SETTINGS

e

DRY

Drum Light

Press this button to turn on the light in the dryer. Press the button again to turn the light off.

This only controls the light when the door is shut.

NOTE: The light will turn off by itself after one minute when the door is shut.

When the door is opened, the light comes on automatically.

The light in center of the button will light up when DRUM LIGHT is on.

NOTE: Hold down the DRUM LIGHT button for 3 seconds to access the SETTINGS menu. (See page 10 for more details)

e-Dry

Reduces the total energy consumption of

This cycle can be used with DELICATES, ACTIVE

specific dryer cycles by adjusting certain heat

WEAR, EASY CARE, NORMAL/MIXED LOADS

settings.

and COTTONS.

LOCK

Push to Lock Control

Hold 3 Secs to Unlock

NOTE: Cycle times will change when e-DRY is selected

Delay Start

Use to delay the start of your dryer.

NOTES:

1. Choose your dry cycle and any options.

If the door is opened while the dryer is

2. Press DELAY START. You can change the

in DELAY, the countdown time will not

restart unless the door is closed and

delay time in 1/2-hour increments, using the

START/PAUSE button has been pressed

S or T arrow pads.

again.

3. Press the START/PAUSE button to start the

You can delay the start of a dry cycle up

countdown.

to 24 hours.

The countdown time will be shown in the

The light in center of the button will light up

ESTIMATED TIME REMAINING display.

when DELAY START is on.

 

 

 

Lock

To lock the dryer, press the LOCK button. To

You can lock the controls to prevent any

unlock the dryer, press and hold the LOCK

button for 3 seconds.

selections from being made. Or you can lock

The light in center of the LOCK button will light

the controls after you have started a cycle.

Children cannot accidentally start the dryer by

up when the controls are locked.

Even though the controls are locked, the POWER

touching pads with this option selected.

 

button is still active in case you have to turn the

 

unit off.

9

About cycle options.

NOTE: Not all features are available on all dryer models.

DRUM

LIGHT

SETTINGS

Press & hold for 3 seconds for secondary options

Settings

Under the SETTINGS option, you can adjust the volume or the brightness of the display.

VOLUME

End of Cycle (signal) volume can be set from

HIGH, MED, LOW or OFF.

Control Sounds volume can be set from

HIGH, MED, LOW or OFF.

DISPLAY BRIGHTNESS can be set from HIGH, MED or LOW.

After you have made your selection, press

ENTER.

NOTE: To access the SETTINGS menu, hold down the DRUM LIGHT button for 3 seconds.

About dryer features.

Drum Lamp

Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer opening from inside the drum. Remove the bulb and replace with the same size bulb.

Built-In Rack Dry System

A handy drying rack may be used for drying items such as tennis shoes. Place items flat on the drying rack and block such items as wool sweaters and delicate fabrics. Dry with low heat.

To install the Built-In Rack Dry System

1. Make sure the drum of the dryer is oriented so the rack drying system is on the left side of the dryer.

2.Pull the drying rack screen out from the left side and engage the handle “posts” in the opposite baffle slots.

3. Place the garment on the rack and close the door. 4. Press the DRYER RACK button.

5. Select desired time.

6. Press the START/PAUSE button.

 

NOTE:

 

Do not use this drying rack when there are other clothes in the dryer.

Engage the handle posts

Make sure to detach the drying rack at the end of the cycle and fully retract the screen back

 

into the baffle.

10

About dryer features (cont.).

GEAppliances.com

To Use the Built-In Hook for

 

Hanging Garments

 

1. Make sure the drum of the dryer is

 

oriented so the hook is on the top

 

center of the dryer.

 

2. Using your finger, pull the hook out of the baffle.

3.Hang the garment on a hanger, hang the hanger on the hook and close the door.

4.Press the DRYER RACK button.

5.Select the desired time.

6.Press the START/PAUSE button.

Reverse Tumble

All Profile front-load matching dryers are equipped with the Reverse Tumblefeature, as part of the Duo Dry Plus system. By reversing the direction of drum rotation during the drying cycle, your dryer will tangle the clothes load less, dry more evenly and improve drying times. Typical loads such as bed and bath mixed loads, where sheets, towels and pillow cases are laundered together, benefit from this capability. When the dryer reverses direction, there will be a slight pause and sound change. This is normal. All dryer cycles utilize this feature, except when the rack dry option is selected, in which case the drum does not tumble.

Using the dryer.

Always follow fabric manufacturer’s care label when laundering.

Sorting and Loading Hints

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items according to size. For example, do not dry a sheet with socks or other small items.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the manufacturer’s instructions.

See below for lint filter cleaning instructions.

Do not overload. This wastes energy and causes wrinkling.

Do not dry the following items: fiberglass items,woolens,rubber-coateditems,plastics, items with plastic trim and foam-filled items.

11

Using the dryer.

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Wash Labels

Machine wash

cycle

 

 

 

 

 

 

 

 

Normal Permanent Press/

 

 

 

Hand wash Do not wash

Do not wring

 

Gentle/

 

 

wrinkle resistant

delicate

 

 

Front load target water temperature

 

 

Target

Automatic

 

Category

Water Temperature

Temperature Control

 

 

 

 

 

Tap Cold

Inlet Water Temperature

Not used

 

 

Cold

27°C/80°F

Used

 

Warm

40°C/105°F

Used

 

Hot

50°C/120°F

Used

 

Sanitize

70°C/160°F

Used

 

 

 

 

 

Dry Labels

Tumble dry

Dry

Normal

 

 

 

 

Do not dry

 

 

 

 

Permanent Press/

Gentle/

Do not tumble dry (used with

 

 

wrinkle resistant

delicate

do not wash)

Heat setting

High

Medium

Low

No heat/air

Special instructions

Line dry/

Drip dry

Dry flat

In the shade

hang to dry

 

 

 

Bleach Labels

Bleach symbols

Any bleach

Only non-chlorine bleach

Do not bleach

(when needed)

(when needed)

 

Care and Cleaning of the Dryer

Dryer Interior and Duct: The interior of the appliance and exhaust duct should be cleaned once a year by qualified service

personnel.

The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty.

Do not touch the surface or the display with sharp objects.

The Lint Filter: Clean the lint filter before each use. Remove by pulling straight up. Run your fingers across the filter. A waxy buildup may form on the lint filter from

12 using dryer-added fabric softener sheets. To remove this buildup, wash the lint screen

in warm, soapy water. Dry thoroughly and replace. Do not operate the dryer without the lint filter in place.

Vacuum the lint from the dryer lint filter if you notice a change in dryer performance.

Stainless Steel: To clean stainless steel surfaces, use a damp cloth with a mild, nonabrasive cleaner suitable for stainless steel surfaces. Remove the cleaner residue, and then dry with a clean cloth.

The stainless steel used to make the dryer drum provides the highest reliability available in a GE dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface blemishes will not affect the function or durability of the drum.

The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there is no wildlife (birds, insects, etc.) nesting inside the duct or hood.

SMART APPLIANCE (on some models)

GEAppliances.com

Models PFDS450, PFDS455, PFDN440, PFDN445 are compatible with the

Settings Menu

GE Smart Appliance Module (SAM) which can be purchased separately.

Press SETTINGS; then select

Contact your local utility or visit www.GEAppliances.com/smart-appliances

Energy Management.

to see if your area is using Demand Response (DR) technology.

 

Installation

 

The preferred location for the module installation is on top of the clothes

 

dryer. Details on how to connect the cables to the module are in the

Delay EP Override

instructions that come with the module.

If you are starting a cycle in

 

 

a Critical or High utility rate,

 

this option allows the unit

 

to automatically run on an

 

EP Cycle. This setting will

 

operate with less energy than normal cycles. Default setting is YES.

Wait 5 minutes; then press the Settings button. Scroll and look for the energy management screen as seen below.

This screen means the module is attached correctly and you can begin to use your Smart Appliance following the instructions below.

If the Energy Management Screen is not available, refer to the SAM module troubleshooting guide.

Quick Guide There are 4 power levels available: Critical, High, Medium and Low. On the Medium and Low levels, the unit runs as normal. The following steps show how the unit reacts during startup at Critical and High power levels.

Option 1 (Delay EP) During startups at Critical and High levels, the unit will delay starting until the level becomes Medium or Low. Press the START/PAUSE button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Option 2 (Override Delay EP)

 

 

 

 

To start the unit when Delay EP is shown, press the DELAY START button to

turn the delay off. Then press START/PAUSE to begin the cycle.

During a Critical Rate period, the Critical Response Mode** will also be

activated to maximize energy savings. EP will be displayed.

 

 

e

DELAY

DRYER

 

 

DRY

START

RACK

BACK

ENTER

Option 3 (Override “e” DRY) After overriding the delay function, pressing the “e”DRY button will disable the “e”DRY setting. Pressing the START/PAUSE key will begin the selected cycle. During a Critical Rate period, the Critical Response Mode** will be activated to maximize energy savings. EP will be displayed. **Note: The Critical Response Mode can be disabled at any time by pressing and holding the “e”DRY Button for 3 seconds. EP will be removed from the display

Auto-Extend Delays If a timed delay is selected, this option allows for the scheduled start to extend if the utility rate is Critical or High at the scheduled start. The default setting will automatically extend these cycles.

Critical Rate Option

This option allows your smart appliance to respond to Critical Rate information by automatically engaging the Critical Response Mode. The Critical Response Mode is designed to maximize energy savings when a cycle is run during a Critical Rate period. The default setting is YES. Setting this option to NO will disable the Critical Response Mode.

Timed Dry EP Option If the unit is running in Timed Dry Mode and the utility rate switches to Critical or High, the unit will conserve energy by decreasing heat if YES (default) is selected. If NO is selected, the unit will operate normally.

NOTE: When YES (default) is selected, your load may be damp at the end of the cycle.

In order for the Smart Appliance features on the appliance to work, additional equipment is required to be installed to interface with the local utility. Such equipment may be sold separately and/or is available through your utility as part of the pilot test program. Check with your utility company to see if a pilot test program is available in your area and for full details.

PLEASE NOTE: If you move to an area where the program is not available, the demand response features cannot be activated and utilized on the appliance. The appliance will function as normal after the demand response equipment has been deactivated or disconnected.

13

Installation

Dryer

Instructions

PFMS450 / PFMS455 / PFMN440 / PFMN445

 

PFDS450 / PFDS455 /PFDN440 / PFDN445 /

Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT Save these instructions for local

electrical inspector’s use.

IMPORTANT Observe all governing codes and ordinances.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – Keep these instructions for future reference.

Clothes dryer installation must be performed by a qualified installer.

This dryer must be exhausted to the outdoors.

Before the old dryer is removed from service or discarded, remove the dryer door.

Service information and the wiring diagram are located in the control console.

Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

Install the dryer where the temperature is above 50°F for satisfactory operation of the dryer control system.

Remove and discard existing plastic or metal foil duct and replace with UL-listed duct.

CALIFORNIA SAFE DRINKING WATER AND

 

TOXIC ENFORCEMENT ACT

 

This act requires the governor of California to publish a

 

list of substances known to the state to cause cancer,

 

birth defects or other reproductive harm and requires

 

businesses to warn customers of potential exposure to such

 

substances. Gas appliances can cause minor exposure to

 

four of these substances, namely benzene, carbon monoxide,

 

formaldehyde and soot, caused primarily by the incomplete

 

combustion of natural gas or LP fuels. Properly adjusted

 

dryers will minimize incomplete combustion. Exposure to

 

these substances can be minimized further by properly

 

venting the dryer to the outdoors.

14

 

FOR YOUR SAFETY:

WARNING Risk of Fire

To reduce the risk of severe injury or death, follow all installation instructions.

Clothes dryer installation must be performed by a qualified installer.

Install the clothes dryer according to these instructions and in accordance with local codes.

This dryer must be exhausted to the outdoors.

Use only rigid metal 4” diameter ductwork inside the dryer cabinet and use only UL approved transition ducting between the dryer and the home duct.

DO NOT install a clothes dryer with flexible plastic ducting materials. If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL-listed and installed in accordance with the instructions found in “Connecting the Dryer to House Vent” on page 26 of this manual. Flexible ducting materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct dryer airflow and increase the risk of fire.

Do not install or store this appliance in any location where it could be exposed to water and/or weather.

Save these instructions. (Installers: Be sure to leave these instructions with the customer.)

FOR GAS MODELS ONLY:

NOTE: Installation and service of this dryer must be performed by a qualified installer, service agency or the gas supplier.

In the Commonwealth of Massachusetts:

This product must be installed by a licensed plumber or gas fitter.

When using ball-type gas shut-off valves, they shall be T-handle-type.

A flexible gas connector, when used, must not exceed 3 feet.

Installation Instructions

UNPACKING YOUR DRYER

Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer legs. Be sure to remove all of the foam pieces around the legs.

Remove the bag containing the literature and serial cable.

LOCATION OF YOUR DRYER

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and for air openings are:

0 inch clearance both sides

1 inch front

3 inches rear

Consideration must be given to provide adequate clearance for proper operation and service.

DRYER DIMENSIONS

3939.1.5”

Front View

(993(100cm).3 cm)

27

.

(68.6 cm)

53”1″

(134(129.6.5cm)

3939.1″.5”

(993(100cm).3 cm)

Side View

32.34 ″

(84733.cm)5”

(85.1 cm)

15

Installation Instructions

REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION

Your dryer is approved for installation in an alcove or closet, as stated on a label on the dryer back.

The dryer MUST be vented to the outdoors. See the EXHAUSTING THE DRYER section.

Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:

0” either side

3” front and rear

Minimum vertical space from floor to overhead shelves, cabinets, ceilings, etc., is 52”.

Closet doors must be louvered or otherwise ventilated and have at least 60 square inches of open area equally distributed. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area equally distributed.

The closet should be vented to the outdoors to prevent gas pocketing in case of gas in the supply line.

No other fuel-burning appliance shall be installed in the same closet with the dryer (gas models only).

NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT THE REAR OF THE DRYER, MINIMUM CLEARANCE FROM THE WALL IS 5.5 INCHES.

BATHROOM OR BEDROOM INSTALLATION

The dryer MUST be vented to the outdoors. See EXHAUSTING THE DRYER.

The installation must conform with local codes or, in the absence of local codes, with the NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric dryers) or NATIONAL FUEL GAS CODE, ANSI Z223 (for gas dryers).

MOBILE OR MANUFACTURED HOME INSTALLATION

The installation must conform to the MANUFACTURED HOME CONSTRUCTION & SAFETY STANDARD, TITLE 24, PART 32–80 or, when such standard is not applicable, with AMERICAN NATIONAL STANDARD FOR MOBILE HOME, NO. 501B.

The dryer MUST be vented to the outdoors with the termination securely fastened to the mobile home structure. (See EXHAUSTING THE DRYER.)

The vent MUST NOT be terminated beneath a mobile or manufactured home.

The vent duct material MUST BE METAL.

FOR GAS MODELS ONLY: KIT 14-D346-33 MUST be used to attach the dryer securely to the structure.

FOR GAS MODELS ONLY: The vent MUST NOT be connected to any other duct, vent or chimney.

Do not use sheet metal screws or other refastening devices which extend into the interior of the exhaust vent.

Provide an opening with a free area of at least 25 sq. in. for introduction of outside air into the dryer room.

GARAGE INSTALLATION (IF ALLOWED BY LOCAL CODES)

Dryers installed in garages must be elevated 18 inches (46cm) above the floor.

16

Installation Instructions

CONNECTING INLET HOSES

CONNECTING INLET HOSES

To produce steam, the dryer must connect to the cold water supply. Since the washer must also connect to the cold water, a “Y” connector is inserted to allow both inlet hoses to make that connection at the same time.

NOTE: Use the new inlet hoses provided; never use old hoses.

1. Turn the cold water faucet off. Remove the washer inlet hose from the washer fill valve connector (cold).

2. Ensure the rubber flat washer is in place and screw the female coupling of the short hose onto the washer fill valve connector. Tighten by hand until firmly seated.

3. Attach the female end of the ‘’Y’’ connector to the male coupling of the short hose. Ensure the rubber flat washer is in place. Tighten by hand until firmly seated.

4. Insert the filter screen in the coupling of the washer’s inlet hose. If a rubber flat washer is already in place remove it before installing the filter screen. Attach this coupling to one male end of the ‘’Y’’ connector. Tighten by hand until firmly seated.

5. Ensure the rubber flat washer is in place and attach the dryer’s long inlet hose to the other male end of the ‘’Y’’ connector. Tighten by hand until firmly seated.

6. Ensure the rubber flat washer is in place and attach the other end of the dryer’s long inlet hose to the fill valve connector at the bottom of the dryer back panel. Tighten by hand until firmly seated.

CONNECTING INLET HOSES (cont.)

7. Using pliers, tighten all the couplings with an additional two–thirds turn.

NOTE: Do not overtighten. Damage to the couplings may result.

8. Turn the water faucet on.

9. Check for leaks around the ‘’Y’’ connector, faucet and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within 42 in. (107 cm) of your washer’s water inlet. The faucets MUST be 3/4 in. (1.9 cm) garden hose-type so inlet hoses can be connected. Water pressure MUST be between 10 and 120 pounds per square inch. Your water department can advise you of your water pressure.

NOTE: A water softener is recommended to reduce buildup of scale inside the steam generator if the home water supply is very hard.

17

GE PFDN440, PFMN445, PFDS450, PFMS455, PFDS455 User Manual 2

Installation Instructions

CONNECTING A GAS DRYER (skip for electric dryers)

TOOLS YOU WILL NEED

10” Adjustable

Flat-blade

wrenches (2)

screwdriver

 

Level

8” Pipe wrench

Slip-joint pliers

MATERIALS YOU WILL NEED

4” dia. metal elbow

Pipe compound

Flexible gas line connector

Duct clamps (2) or Spring clamps (2)

Safety glasses

4” dia. metal duct (recommended)

4” dia., UL-listed flexible metal duct (if needed)

Gloves

Soap solution for leak detection

Exhaust hood

Duct tape

FOR YOUR SAFETY:

WARNING

Before beginning the installation, turn off the circuit breaker(s) or remove the dryer’s circuit fuse(s) at the electrical box. Be sure the dryer cord is unplugged from the wall.

Turn the dryer’s gas shut-off valve in the supply line to the OFF position.

Shut-off

Valve

Disconnect and discard old flexible gas connector and ducting material.

18

Installation Instructions

GAS REQUIREMENTS

WARNING

Installation must conform to local codes and ordinances, or in their absence, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

This gas dryer is equipped with a Valve and Burner Assembly for use only with natural gas. Using conversion kit 14-A048, your local service organization can convert this dryer for use with propane (LP) gas. ALL CONVERSIONS MUST BE MADE BY PROPERLY TRAINED AND QUALIFIED PERSONNEL AND IN ACCORDANCE WITH LOCAL CODES AND ORDINANCE REQUIREMENTS.

The dryer must be disconnected from the gas supply piping system during any pressure testing of that system at a test pressure in excess of 0.5 PSI (3.4 KPa).

The dryer must be isolated from the gas supply piping system by closing the equipment shut-off valve during any pressure testing of the gas supply piping of test pressure equal to or less than 0.5 PSI (3.4KPa).

DRYER GAS SUPPLY CONNECTION

2” (5.1 cm)

3/8NPT MALE THREAD GAS SUPPLY

25ø8” (6.7 cm) NOTE: Add to vertical dimension the distance between cabinet bottom to floor.

You must use with this dryer a flexible metal connector (listed connector ANSI Z21.24 / CSA 6.10). The length of the connect shall not exceed 3 ft.

GAS SUPPLY

A 1/8” National Pipe Taper thread plugged tapping, accessible for test gauge connection, must be installed immediately upstream of the gas supply connection to the dryer. Contact your local gas utility should you have questions on the installation of the plugged tapping.

Supply line is to be 1/2” rigid pipe and equipped with an accessible shutoff within 6 feet of, and in the same room with, the dryer.

Use pipe thread compound appropriate for natural or LP gas or use Teflon® tape.

Connect flexible metal connector to dryer and gas supply.

IN THE COMMONWEALTH OF

MASSACHUSETTS

This product must be installed by a licensed plumber or gas fitter.

When using ball-type gas shut-off valves, they shall be the T-handle type.

A flexible gas connector, when used, must not exceed 3 feet.

ADJUSTING FOR ELEVATION

Gas clothes dryers input ratings are based on sea level operation and need not be adjusted for operation at or below 2000 ft. elevation. For operation at elevations above 2000 ft., input ratings should be reduced at a rate of 4 percent for each 1000 ft. above sea level.

Installation must conform to local codes and ordinances or, in their absence, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1

19

Installation Instructions

CONNECTING A GAS DRYER (cont.)

CONNECTING THE DRYER TO THE GAS SUPPLY

AInstall a female 3/8” NPT elbow at the end of the dryer gas inlet.

Install a 3/8” flare union adapter to the female elbow.

IMPORTANT: Use a pipe wrench to securely hold on to the end of the dryer gas inlet to prevent twisting the inlet.

NOTE: Apply pipe compound or Teflon® tape to the threads of the adapter and dryer gas inlet.

New Metal

 

Adapter

Flexible Gas

 

1/8” NPT

Line Connector

 

Adapter

 

Pipe Plug for

 

Checking Gas

Elbow

3/8” NPT

Inlet Pressure

 

Shut-Off Valve

Items not supplied

 

 

Pipe size at

 

 

 

 

least 1/2”

BAttach the flexible metal gas line connector to the adapter.

Apply pipe compound to the adapter and dryer gas inlet.

CTighten the flexible gas line connection, using two adjustable wrenches.

CONNECTING THE DRYER TO THE GAS

SUPPLY (cont.)

DInstall a 1/8” NPT plugged tapping to the dryer gas line shut-off valve for checking gas inlet pressure.

Install a flare union adapter to the plugged tapping.

NOTE: Apply pipe compound or Teflon® tape to the threads of the adapter and plugged tapping.

Apply pipe compound

Plugged

or Teflon® tape to all

male threads.

Tapping

Shut-Off

Valve

ETighten all connections, using two adjustable wrenches. Do not overtighten.

F Open the gas shut-off valve.

20

Installation Instructions

TEST FOR LEAKS

WARNING – Never use an open flame to test for gas leaks.

Check all connections for leaks with soapy solution or equivalent.

Apply a soap solution. The leak test solution must not contain ammonia, which could cause damage to the brass fittings.

If leaks are found, close the valve, retighten the joint and repeat the soap test.

Open Gas

Valve

ELECTRICAL CONNECTION INFORMATION FOR GAS DRYERS

WARNING – To reduce the risk of fire, electrical shock and personal injury:

Do not use an extension cord or an adapter plug with this appliance.

The dryer must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, in accordance with the NATIONAL ELECTRICAL CODE, ANSI/NFPA NO. 70 or Canadian Electrical Code, CSA C22.1

ELECTRICAL REQUIREMENTS FOR GAS DRYERS

This appliance must be supplied with 120V, 60Hz, and connected to a properly grounded branch circuit, protected by a 15or 20-amp circuit breaker or time-delay fuse.

If electrical supply provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet.

WARNING – This dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding terminal from this plug.

Ensure proper ground exists before use.

If local codes permit, an external ground wire (not provided), which meets local codes, may be added by attaching to the green ground screw on the rear of the dryer, and to an alternate established ground.

Ensure proper ground exists before use.

Ground

Screw

21

Installation Instructions

CONNECTING AN ELECTRIC DRYER (skip for gas dryers)

TOOLS YOU WILL NEED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Phillips screwdriver

 

Slip-joint pliers

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flat-blade crewdriver

Level

MATERIALS YOU WILL NEED

4” dia. metal elbow

3/4” strain relief (UL recognized)

4” duct clamps (2) or 4” spring clamps (2)

Safety glasses

4” dia. metal duct (recommended)

4” dia., UL-listed flexible metal duct (if needed)

Gloves

Exhaust hood

Duct tape

Dryer power cord kit (not provided with dryer)

UL rated 120/240V, 30A with 3 or 4 prongs. Identify the plug type as per the house receptacle before purchasing line cord.

FOR YOUR SAFETY:

WARNING

Before making the electrical connection, turn off the circuit breaker(s) or remove the dryer’s circuit fuse(s) at the electrical box. Be sure the dryer cord

is unplugged from the wall. NEVER LEAVE THE ACCESS COVER OFF THE TERMINAL BLOCK.

ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS

WARNING – To reduce the risk of fire, electrical shock and personal injury:

Do not use an extension cord or an adapter plug with this appliance.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA NO. 70 or Canadian Electrical Code, CSA C22.1.

22

Installation Instructions

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS

This dryer must be connected to an individual branch circuit, protected by the required time-delay fuses or circuit breakers. A threeor four-wire, single-phase, 120/240V or 120/208V, 60Hz, 30-amp circuit is required.

If the electric supply does not meet the above specifications, then call a licensed electrician.

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS (CANADA)

This dryer must be connected to an individual branch circuit, protected by the required time-delay fuses or circuit breakers. The power supply must be of 120/240 volts, 60Hz circuit with the wall receptacle as shown below.

G

YX

W

TYPICAL 30 AMP

RECEPTACLE FOR DRYER

The power supply must be protected with 30 Amp fuses or breakers. It must be well grounded and conform to local codes.

GROUNDING INSTRUCTIONS

This dryer must be connected to a grounded metal, permanent wiring system, or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal on the appliance.

GROUNDING INSTRUCTIONS (CANADA)

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electrical current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

CONNECTING DRYER USING 4-WIRE CONNECTION (MUST BE USED FOR MOBILE HOME INSTALLATION)

NOTE: Since January 1, 1996, the National Electrical Code requires that new constructions utilize a 4-wire connection to an electric dryer. A 4-wire cord must also be used where local codes do not permit grounding through the neutral.

3-wire connection is NOT for use on new construction.

 

 

 

 

Relocatre

 

 

 

Green

green ground

4 #10 AWG

Hot Wire

screw here

Screw Wire

 

 

 

 

 

 

minimum

 

Screw

 

 

 

 

copper

Remove

 

 

 

 

conductors

ground strap

 

 

 

 

or 120/240V

and discard.

 

 

 

 

30A power

Keep green

 

 

 

 

supply cord kit

ground

Neutral

 

 

 

 

marked for use

screw.

(white)

 

 

 

 

with dryers

 

Hot Wire

 

 

Strain

and provided

 

 

 

with closed

 

3/4” UL

Relief

 

 

Screw

loop or spade

 

 

Recognized

Bracket

 

 

 

Strain Relief

 

terminals with

 

 

 

 

upturned ends

(not supplied)

1.Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.

2.Be sure the dryer cord is unplugged from the wall receptacle.

3.Remove the power cord cover located at the lower back.

4.Remove and discard ground strap. Keep the green ground screw for Step 7.

5.Install 3/4 in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief.

6.Connect power cord as follows:

A.Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2).

B.Connect the neutral (white) line to the center of the terminal block (marked N).

7.Attach ground wire of power cord with the green ground screw (hole above strain relief bracket). Tighten all terminal block screws (3) securely.

8.Properly secure power cord to strain relief.

9.Reinstall the cover.

WARNING – NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.

23

Installation Instructions

CONNECTING AN ELECTRIC DRYER (cont.)

CONNECTING DRYER USING 3-WIRE CONNECTION

If required, by local code, install external ground (not provided) to grounded metal, cold water pipe, or other established ground determined by a qualified electrician.

 

Hot Wire

Screw

 

3 #10 AWG

Screw

 

 

 

minimum

Ground

 

 

 

copper

 

 

 

conductors or

Strap

 

 

 

 

 

 

120/240V 30A

 

 

 

 

Green

 

 

 

power supply

ground

 

 

 

cord kit marked

screw

 

 

 

for use with

Neutral

 

 

 

dryers and

(white)

 

3/4” UL

Strain

provided with

Hot Wire

Screw

closed loop or

Recognized

Relief

spade terminals

 

 

 

 

Strain Relief

Bracket

with upturned

ends (not supplied)

3-wire Connection

Not for use in Canada.

DO NOT use for Mobile Home Installations. NOT for use on new construction.

NOT for use on recreational vehicles.

NOT for use in areas where local codes prohibit grounding through the neutral conduction.

CONNECTING DRYER USING 3-WIRE

CONNECTION (cont.)

1.Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall receptacle.

3.Remove the power cord cover located at the lower back.

4.Install 3/4-in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief.

5.Connect power cord as follows:

A.Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2).

B.Connect the neutral (white) line to the center of the terminal block (marked N).

6. Be sure ground strap is connected to neutral (center) terminal of block and to green ground screw on cabinet rear. Tighten all terminal block screws (3) securely.

7.Properly secure power cord to strain relief.

8.Reinstall the cover.

WARNING – NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.

24

Installation Instructions

EXHAUSTING THE DRYER

WARNING – To reduce the risk of fire or personal injury:

This clothes dryer must be exhausted to the outdoors.

Use only 4” rigid metal ducting for the home exhaust duct.

Use only 4” rigid metal or UL-listed flexible metal (semi-rigid or foil-type) duct to connect the dryer to the home exhaust duct. It must be installed in accordance with the instructions found in “Connecting the Dryer to House Vent” on page 26 of this manual.

Do not terminate exhaust in a chimney, a wall, a ceiling, gas vent, crawl space, attic, under an enclosed floor, or in any other concealed space of a building. The accumulated lint could cause a potential fire hazard.

Never terminate the exhaust into a common duct with a kitchen exhaust system. A combination of grease and lint creates a potential fire hazard.

Do not use duct longer than specified in the exhaust length table. Longer ducts can accumulate lint, creating a potential fire hazard.

Never install a screen in or over the exhaust duct. This will cause lint to accumulate, creating a potential fire hazard.

Do not assemble ductwork with any fasteners that extend into the duct. These fasteners can accumulate lint, creating a potential fire hazard.

Do not obstruct incoming or exhausted air.

Provide an access for inspection and cleaning of the exhaust system, especially at turns and joints. Exhaust system shall be inspected and cleaned at least once a year.

This dryer comes ready for rear exhausting. If space is limited, use the instructions on pages 29–31 to exhaust directly from the sides or bottom of the cabinet.

EXHAUST SYSTEM CHECKLIST

HOOD OR WALL CAP

Terminate in a manner to prevent back drafts or entry of birds or other wildlife.

Termination should present minimal resistance to the exhaust airflow and should require little or no maintenance to prevent clogging.

Never install a screen in or over the exhaust duct.

Wall caps must be installed at least 12” above ground level or any other obstruction with the opening pointed down.

SEPARATION OF TURNS

For best performance, separate all turns by at least 4 ft. of straight duct, including distance between last turn and dampened wall cap.

SEALING OF JOINTS

All joints should be tight to avoid leaks. The male end of each section of duct must point away from the dryer.

Do not assemble the ductwork with fasteners that extend into the duct. They will serve as a collection point for lint.

Duct joints should be made airand moisture-tight by wrapping the overlapped joints with duct tape or aluminum tape.

Horizontal runs should slope down towards the outdoors 1/4” per foot.

INSULATION

Ductwork that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint buildup.

TOOLS AND MATERIALS YOU WILL NEED TO INSTALL EXHAUST DUCT

Phillips-head screwdriver

Rigid or UL-listed flexible metal 4” (10.2 cm) duct

Duct tape or duct clamp

Drill with 1/8” drill bit

(for bottom venting)

Vent hood

 

Hacksaw

 

25

Installation Instructions

EXHAUSTING THE DRYER (cont.)

CONNECTING THE DRYER TO HOUSE VENT

RIGID METAL TRANSITION DUCT

For best drying performance, a rigid metal transition duct is recommended.

Rigid metal transition ducts reduce the risk of crushing and kinking.

UL-LISTED FLEXIBLE METAL (SEMI-RIGID) TRANSITION DUCT

If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077).

Never install flexible metal duct in walls, ceilings, floors or other enclosed spaces.

Total length of flexible metal duct should not exceed 8 feet (2.4 m).

For many applications, installing elbows at both the dryer and the wall is highly recommended (see illustrations at right). Elbows allow the dryer to sit close to the wall without kinking and/or crushing the transition duct, maximizing drying performance.

Avoid resting the duct on sharp objects.

UL-LISTED FLEXIBLE METAL (FOIL-TYPE) TRANSITION DUCT

In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct.

In Canada and the United States, only the flexible metal (foil-type) ducts that comply with the “Outline for Clothes Dryer Transition Duct Subject 2158A” shall be used.

Never install flexible metal duct in walls, ceilings, floors or other enclosed spaces.

Total length of flexible metal duct should not exceed 8 feet (2.4 m).

Avoid resting the duct on sharp objects.

For best drying performance:

1.Slide one end of the duct over the clothes dryer outlet pipe.

2.Secure the duct with a clamp.

3.With the dryer in its permanent position, extend the duct to its full length. Allow 2” of duct to overlap the exhaust pipe. Cut off and remove excess duct. Keep the duct as straight as possible for maximum airflow.

4.Secure the duct to the exhaust pipe with the other clamp.

FOR TRANSITION VENTING (DRYER TO WALL), DO:

DO cut duct as short as possible and install straight into wall.

DO use elbows when turns are necessary.

Elbows

DO NOT:

DO NOT bend or collapse ducting. Use elbows

if turns are necessary.

DO NOT use excessive exhaust length. Cut duct as short as possible.

DO NOT crush duct against the wall.

DO NOT set dryer on duct.

26

Installation Instructions

WARNING – USE ONLY METAL 4” DUCT. DO NOT USE DUCT LONGER THAN SPECIFIED IN THE EXHAUST LENGTH TABLE.

Using exhaust longer than specified length will:

Increase the drying times and the energy cost.

Reduce the dryer life.

Accumulate lint, creating a potential fire hazard.

The correct exhaust installation is YOUR RESPONSIBILITY.

Problems due to incorrect installation are not covered by the warranty.

The MAXIMUM ALLOWABLE length of the exhaust system depends upon the type of duct, number of turns, the type of exhaust hood (wall cap) and all conditions noted below.

EXHAUST LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

Use only for short-run

 

installations

4” DIA

4” DIA

 

 

4” DIA

 

 

4”

21ø2

 

 

No. of 90º

Rigid

Rigid

Elbows

Metal

Metal

0

150 Feet

125 Feet

1

135 Feet

115 Feet

2

125 Feet

105 Feet

3

115 Feet

95 Feet

4

105 Feet

85 Feet

5

95 Feet

75 Feet

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

The total vent system length includes all the straight portions and elbows of the system (transition duct included).

27

EXHAUST SYSTEM CHECKLIST

HOOD OR WALL CAP

Terminate in a manner to prevent back drafts or entry of birds or other wildlife.

Termination should present minimal resistance to the exhaust airflow and should require little or no maintenance to prevent clogging.

Never install a screen in or over the exhaust duct. This could cause lint buildup.

Wall caps must be installed at least 12” above ground level or any other obstruction with the opening pointed down.

SEPARATION OF TURNS

For best performance, separate all turns by at least 4 ft. of straight duct, including the distance between the last turn and the exhaust hood.

TURNS OTHER THAN 90º

One turn of 45º or less may be ignored.

Two 45º turns should be treated as one 90º turn.

Each turn over 45º should be treated as one 90º turn.

SEALING OF JOINTS

All joints should be tight to avoid leaks. The male end of each section of duct must point away from the dryer.

Do not assemble the ductwork with fasteners that extend into the duct. They will serve as a collection point for lint.

Duct joints can be made airand moisture-tight by wrapping the overlapped joints with duct tape.

Horizontal runs should slope down toward the outdoors 1/4” per foot.

INSULATION

Ductwork that runs through an unheated area or is near air conditioning should be insulated to reduce condensation and lint buildup.

Installation Instructions

EXHAUSTING THE DRYER (cont.)

BEFORE YOU BEGIN

Remove and discard existing plastic or metal foil duct and replace with UL-listed duct.

Remove any lint from the wall exhaust opening.

Wall

Internal

Duct

Opening

Check that exhaust

hood damper opens

and closes freely.

STANDARD REAR EXHAUST

We recommend that you install your dryer before installing your washer. This will permit direct access for easier exhaust connection.

Slide the end of the exhaust duct on the back of the dryer and secure with duct tape or a hose clamp.

RECOMMENDED CONFIGURATION TO MINIMIZE EXHAUST BLOCKAGE

Using duct elbows will prevent duct kinking and collapsing.

Transition

Ducting

Duct

NOTE: We strongly recommend using rigid metal exhaust duct.

For straight-line installation, connect the dryer exhaust to the wall, using duct tape.

Wall Side

Dryer

Side

28

Installation Instructions

SIDE VENTING:

Dryer Exhaust to right of cabinet for Electric models only.

Dryer Exhaust to left of cabinet for Gas and Electric models.

WARNING–BEFOREPERFORMING THIS EXHAUST INSTALLATION, BE SURE TO DISCONNECT THE DRYER FROM ITS ELECTRICAL SUPPLY. PROTECT YOUR HANDS AND ARMS FROM SHARP EDGES WHEN WORKING INSIDE THE CABINET. BE SURE TO WEAR GLOVES.

Remove Right screw and save

Left

Bottom

Remove desired knockout (one only)

Detach and remove the bottom, right or left side knockout as desired. Remove the screw inside the dryer exhaust duct and save. Pull the duct out of the dryer.

Fixing hole

A

13 1ø2

Cut the duct as shown and keep portion A.

TAB LOCATION

Not for gas

Bend tab up 45°

Through the rear opening, locate the tab in the middle of the appliance base. Lift the tab to about

45°, using a flat-blade screwdriver.

29

ADDING A NEW DUCT

Fixing hole

Portion “A”

Left side exhaust

Reconnect the cut portion (A) of the duct to the blower housing. Make sure that the shortened duct is aligned with the tab in the base. Use the screw saved previously to secure the duct in place through the tab on the appliance base.

ADDING ELBOW AND DUCT FOR EXHAUST TO LEFT OR RIGHT SIDE OF CABINET

Internal duct

Rear opening

Side opening

Insert the 4” elbow through the rear opening and connect the elbow to the dryer internal duct.

Insert the 4” duct through the side opening and connect it to the elbow.

CAUTION: Do not pull or damage the electrical wires and do not remove the vinyl cover from the electrical components inside the dryer when inserting the duct. A slight interference may occur between the exhaust and the wire components.

Installation Instructions

EXHAUSTING THE DRYER (cont.)

SIDE VENTING (cont.)

ADDING ELBOW AND DUCT FOR EXHAUST TO LEFT OR RIGHT SIDE OF CABINET (cont.)

• Apply

duct

tape as

Duct tape

shown

on

the

joint

 

between the

dryer

 

internal duct and the

 

elbow,

and

also the

 

joint

between

the

 

elbow

and

the

side

 

duct.

 

 

 

 

CAUTION: Use 4” rigid metal ducting only inside the dryer. Internal duct joints must be secured with tape, otherwise they may separate and cause a safety hazard.

ADDING COVER PLATE TO REAR OF CABINET (SIDE EXHAUST)

Plate

(Kit WE1M454)

Connect standard metal elbows and ducts to complete the exhaust system. Cover back opening with a plate (Kit WE1M454) available from your local service provider. Place dryer in final location.

WARNING – NEVER LEAVE THE BACK OPENING WITHOUT THE PLATE. (Kit

WE1M454)

BOTTOM VENTING:

Dryer Exhaust to the bottom of cabinet for Gas and Electric models.

WARNING – BEFORE PERFORMING THIS EXHAUST INSTALLATION, BE SURE TO DISCONNECT THE DRYER FROM ITS ELECTRICAL SUPPLY. PROTECT YOUR HANDS AND ARMS FROM SHARP EDGES WHEN WORKING INSIDE THE CABINET. BE SURE TO WEAR GLOVES.

Remove screw and save

Bottom

Remove desired knockout (one only)

Remove the screw inside the dryer exhaust duct and save. Pull the duct out of the dryer. Detach and remove the bottom knockout.

Fixing hole

A

13 1ø4

Cut the duct as shown and keep portion A.

30

Loading...
+ 126 hidden pages