GE 28041xx4, 28041xx1, 28041xx2, 28041xx3, 8005 User Manual

...
0 (0)

Model 28041

5.8GHz Color Handset Speakerphone/Answering System User’s Guide

Equipment Approval Information

Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.

1Notification to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.

The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

Notes

This equipment may not be used on coin service provided by the telephone company.

Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company.

Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

US Number is located on the cabinet bottom.

REN Number is located on the cabinet bottom.

2Rights of the Telephone Company

Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary

discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.

The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or performance of your

telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.

Interference Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).

Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.

Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.

Hearing Aid Compatibility (HAC)

This telephone system meets FCC standards for Hearing Aid Compatibility.

Licensing

Licensed under US Patent 6,427,009.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.”

For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the belt clip supplied with this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

Table of Contents

Equipment Approval Information..................

2

Interference Information.............................

3

Hearing Aid Compatibility (HAC)..................

3

Licensing......................................................

3

FCC RF Radiation Exposure Statement.........

3

Table of Contents........................................

4

Introduction................................................

6

Before You Begin.........................................

6

Parts Checklist..................................................

6

Telephone Jack Requirements.........................

7

Installation..................................................

7

Digital Security System....................................

7

Important Installation Guidelines..................

8

Handset Layout............................................

9

Base Layout................................................

10

Installing the Phone..................................

11

Installing the Handset Battery...................

11

Base Station....................................................

12

Wall Mounting.........................................

12

Answering System Setup.............................

13

Setting the Voice Prompt Language...........

13

Voice Time/Day Stamp & Real Time Clock 13

Speaker Volume..............................................

14

Recording the Outgoing Announcement...

14

Reviewing & Choosing the Announcement15

Audible Quick Setup Guide...........................

15

Programming the Telephone.......................

15

Phone Setting.................................................

16

Language.....................................................

16

Area Code...................................................

17

Registration................................................

17

Handset Name............................................

18

Deregistration............................................

18

Global De-Registration...........................

19

Default Setting..........................................

20

Display Setting ..............................................

20

Wallpaper...................................................

20

Color Scheme............................................

21

Set Contrast..............................................

21

Sound Setting ................................................

21

Ringer Volume...........................................

22

Ringer Tone................................................

22

Key Tone......................................................

22

Answering System Operation......................

23

Message Counter...........................................

23

Mailbox Indicator...........................................

24

Leaving a Message..........................................

24

Screening Calls from the Base...................

24

Memory Full...................................................

24

Messages Playback.........................................

25

Leaving a Memo..............................................

26

Answering System Remote Access...............

26

Remote Access from Cordless Handset....

26

Remote Access Security Code......................

27

Ring to Answer...............................................

27

New Message Alert.......................................

28

Screening Calls from the Handset............

28

Memory Full...................................................

29

Telephone Operation..................................

29

CHARGE/IN USE Indicator on the Base29

Visual Ring Indicator on the Handset..

29

Standby Screen..........................................

29

Making a Call.................................................

30

Answering a Call...........................................

30

Volume..............................................................

30

Call Timer........................................................

30

Auto Standby..................................................

30

Flash/Call Waiting.......................................

30

Last Number Redial.......................................

31

Exit....................................................................

31

Page..................................................................

31

Paging from the Base/Group Page........

31

Handset to Handset Paging....................

32

Mute.................................................................

32

Ringer Volume (Shortcut)............................

32

Do Not Disturb (DND) ................................

33

Room Monitor................................................

33

Intercom Operation....................................

34

Handset to Handset Intercom Call...........

34

Receiving an Intercom Call..........................

35

Advanced Intercom Features.......................

35

Receiving an Incoming Call ....................

35

Using with External Telephone Calls..

35

Two-Way Calling.....................................

35

Three-way Conferencing.........................

36

Call Transfer..................................................

36

Transferring Calls to Handsets............

36

Caller ID (CID)..........................................

37

Call Waiting Caller ID................................

37

CID Error Codes...........................................

38

Receiving CID Records..................................

38

Storing CID Records (In CID Memory).....

38

Reviewing CID Records................................

38

Dialing a CID Number...................................

38

Formatting a CID Number Before Dialing38

Storing CID Records into Phone Book.....

39

Deleting a CID Record.................................

40

Deleting All CID Records...........................

40

Phone Book...............................................

41

Adding Phone Book Entries.........................

41

Storing the Last Number Dialed.................

42

Inserting a Pause in the Dialing Sequence43

Reviewing Phone Book Records..................

43

Editing a Phone Book Record.....................

44

Deleting a Phone Book Record..................

44

Dialing a Phone Book Record.....................

44

Chain Dialing from Phone Book.................

45

Picture Download.....................................

45

Download Your Own Image........................

45

One-Time Software Installation............

45

Image Editing..............................................

46

Image Downloading.......................................

46

Choosing the Downloaded Image as

 

Wallpaper........................................................

46

Assigning the Downloaded Image to Phone

Book Record...................................................

46

Recording Ringer Tones.............................

47

Record Your Own Ringer Tones.................

47

Record with Included Audio Cable

 

or an Optional Headset ......................

48

Record with the Handset Microphone .....

49

Choosing the Recorded Sound Clip

 

as Ringer Tone............................................

49

Assigning the Recorded Sound Clip to Phone

Book Record...................................................

49

Belt Clip and Optional Headset.................

50

Connecting the Belt Clip..............................

50

Connecting an Optional Headset

 

to the Handset............................................

50

Changing the Battery.................................

50

Battery Safety Precautions........................

51

Display Messages........................................

51

Answering System Display Messages...........

53

Handset Sound Signals..............................

53

Troubleshooting Guide..............................

53

Telephone Solutions.................................

53

Caller ID Solutions.................................

55

Battery Solutions.....................................

56

Causes of Poor Reception..........................

56

General Product Care...............................

56

Service.......................................................

57

Accessory Information...............................

57

Index..........................................................

58

Limited Warranty.......................................

60

WARNING:TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSETHIS PRODUCT TO RAIN OR MOISTURE.

 

 

 

 

 

 

 

CAUTION:

 

 

 

 

RISKOFELECTRICSHOCK

 

 

 

 

DONOTOPEN

 

 

THE LIGHTNING

CAUTION: TO REDUCE THE

THE EXCLAMATION

FLASH AND ARROW

RISK OF ELECTRIC SHOCK, DO

POINT WITHIN THE

HEAD WITHIN THE

NOT REMOVE COVER (OR

TRIANGLE IS A

TRIANGLE IS A

BACK). NO USER

WARNING SIGN

WARNING SIGN

SERVICEABLE PARTS INSIDE.

ALERTING YOU OF

ALERTING YOU OF

REFER SERVICING TO

IMPORTANT

“DANGEROUS

QUALIFIED SERVICE

INSTRUCTIONS

VOLTAGE” INSIDE

PERSONNEL.

ACCOMPANYING

THE PRODUCT.

 

 

 

THE PRODUCT.

 

 

 

 

 

SEE MARKING ON BOTTOM / BACK OF PRODUCT

Introduction

CAUTION: When using telephone equipment, there are basic

safety instructions that should always be followed. Refer to the

IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference.

IMPORTANT: Because cordless phones operate on electricity, you should have at least one phone in your home that isn’t cordless, in case the power in your home goes out.

Before You Begin

Parts Checklist (for model 28041xx1)

Make sure your package includes the items shown here.

 

AC power

Telephone

Base

adaptor

line cord

 

 

Handset

Handset

Battery

Image

battery pack

compartment

Editor

 

cover

Software

Ringer

USB

 

 

recording

download

Belt clip

Wall mount

cable

cable

bracket

 

For Model 28041xx2 there will be ONE additional handset, charge cradle, belt clip, battery pack and cover than shown above.

For Model 28041xx3 there will be TWO additional handsets, charge cradles, belt clips, battery packs and covers than shown above.

For Model 28041xx4 there will be THREE additional handsets, charge cradles, belt clips, battery packs and covers than shown above.

Telephone Jack Requirements

Wall plate

To use this phone, you need an RJ11C type modular telephone

 

jack, which might look like the one pictured here, installed in your

Modular

home. If you don’t have a modular jack, call your local phone

company to find out how to get one installed.

telephone

line jack

 

Installation

Digital Security System

Your cordless phone uses a digital security system to protect against false ringing, unauthorized access, and charges to your phone line.

INSTALLATION NOTE: Some cordless telephones operate at frequencies that may cause or receive interference with nearby TVs, microwave ovens, and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV, microwave ovens, or VCR. If such interference continues, move the cordless telephone farther away from these appliances.

Certain other communications devices may also use the 5.8 GHz frequency for communication, and, if not properly set, these devices may interfere with each other and/or your new telephone. If you are concerned with interference, please refer to the owner’s manual for these devices on how to properly set channels to avoid interference. Typical devices that may use the 5.8 GHz frequency for communication include wireless audio/video senders, wireless computer networks, multi-handset cordless telephone systems, and some long-range cordless telephone systems.

Important Installation Guidelines

Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave ovens, heating appliances and direct sunlight.

Avoid areas of excessive dust, moisture and low temperature.

Avoid other cordless telephones or personal computers.

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch non-insulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Handset Layout

VISUAL RING

INDICATOR LIGHT

EARPIECE

display

TALK/CALL BACK (button)

MENU (button)

CALLER ID-VOLUME (button)

SPEAKER (button)

REDIAL (button)

rev (review button)

* EXIT (button)

erase (button)

INTERCOM (button)

MICROPHONE

SELECT/MUTE

(button)

CALLER ID-VOLUME

(button)

PHONEBOOK (button)

skip (button) play (button)

# PAUSE/

RINGER (button)

FLASH/DELETE

(button)

GE 28041xx4, 28041xx1, 28041xx2, 28041xx3, 8005 User Manual

Base Layout

DAY/CHECK

HOUR

MIN

(button)

(button)

(minute button)

SPEAKER

VOL

 

(volume buttons)

REVIEW

Message

(button)

indicator

 

SKIP

 

(button)

 

ANNOUNCE 1

 

(button)

 

ANNOUNCE 2

 

(button)

 

PLAY/STOP 1

 

(button/indicator)

 

PLAY/STOP 2

 

(button/indicator)

 

PLAY/STOP 3

 

(button/indicator)

DELETE (button)

 

 

 

 

 

DO NOT DISTURB

PAGE

CHARGE/IN USE

MEMO

 

Microphone

(button)

 

 

(button)

(indicator)

(button)

 

 

 

 

 

ANS ON/OFF

LANGUAGE

 

 

(answerer button)

(button)

10

Installing the Phone

Installing the Handset Battery

NOTE: You must connect the handset battery before using the cordless handsets.

CAUTION: To reduce the risk of fire or personal injury, use only the Thomson Inc. approved model 5-2660 Nickel-metal Hydride battery (Ni-MH), which is compatible with this unit.

1.Locate battery and battery door which are packaged together inside a plastic bag and are separate from the handset.

2.Locate the battery compartment on the back of the handset.

3.Plug the battery pack cord into the jack inside the compartment.

NOTE: It is important to maintain the polarity (black and red wires) to the jack inside the compartment. To ensure proper battery installation, the connector is keyed and can be inserted only one way.

battery pack

black wire

PRESS DOWN

 

FIRMLY

red wire

 

4.Insert the battery pack.

5.Close the battery compartment by pushing the door up until it snaps into place.

6.Place the handset in the charging cradle.

Allow handset to charge for 16 hours prior to first use. If you do not properly charge the handset, battery performance is compromised.

11

Base Station

1.Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and place your cordless telephone on a level surface, such as a desktop or tabletop, or you may mount it on the wall.

2.Plug one end of the telephone line cord into the TEL LINE jack on the bottom of the base and the other end into a modular jack.

3.Plug the AC power converter into the electrical outlet and the DC connector into the jack on the bottom of the base.

4.Place the handset in the base cradle. The CHARGE/IN USE indicator turns on, verifying the battery is charging.

5.Allow the phone to charge for 16 hours prior to first use. If you don’t properly charge the phone, battery performance is compromised.

CAUTION: Use only the model 5-2605 power adaptor that came

with this unit. Using other power adaptors may damage the unit.

Wall Mounting

1.Turn the base over.

2.Attach the wall mounting pedestal by first inserting the tabs on the open edge of the pedestal into the slots on the lower portion of the bottom of the base. Then push down and snap the pedestal into place.

3.Slip the mounting holes (on the back of the base) over the wall plate posts, and slide the unit down into place. (Wall plate not included.)

NOTE : If desired, gather the extra telephone line and power adaptor cord and store inside the wall mounting bracket.

12

Answering System Setup

This section shows you how to set up your answering system to receive incoming calls. Before you begin the set up process, you must turn on the answering system.

Press the ANS ON/OFF button to turn the answering system on and off.

The MESSAGES indicator lights when the answering system is on. The indicator blinks when you have new messages.

NOTE: The answering system displays “- -” when it is off.

Setting the Voice Prompt Language

The default voice prompt language is English.

To change the answering system’s voice prompt language,

Press the LANGUAGE button on front of base to change to the FRENCH voice prompt. The unit announces “OPTION FRANCAISE" and Fr shows in the message counter.

Press the LANGUAGE button again to change to the SPANISH voice prompt. The unit announces “SELECCION ESPANOL” and SP shows in the message counter.

NOTE: To change to English, press the LANGUAGE button again.

NOTE: In remote access mode, the system follows the selected language. The voice prompt language cannot be switched remotely.

Voice Time/Day Stamp and Real Time Clock

1.Make sure the answering system is ON.

2.Press and hold the DAY/CHECK button to set the day of the week.

3.Press and hold the HOUR button to set the hour (a.m. or p.m.). Example: 12AM, 1AM, or 12PM, 1PM.

4.Press and release the MIN button to advance the clock in one minute intervals. Press and hold to increase by 5-minute increments.

5.After the time is set, the real time clock will be displayed on the handset within 1 minute.

13

NOTE: You must set the day manually. You may choose to set the time manually as well, although the time is automatically transmitted by your local phone company as part of Caller ID service. If you subscribe to Caller ID service, the current time is set automatically when you receive your first CID record.

Speaker Volume

Use the VOLUME (5 or 6) buttons to adjust speaker volume on the base to a comfortable level. L1 is the minimum speaker volume and L8 is the maximum.

Recording the Outgoing Announcement

For best results when recording, you should be about nine inches from the microphone, and eliminate as much background noise as possible.

You may record 2 outgoing announcements in the answerer or choose the default for your current outgoing announcement.

1.Make sure the answering system is ON.

2.Press and hold the ANNOUNCE 1 or ANNOUNCE 2 button until the speaker announces “RECORD ANNOUNCEMENT AFTER TONE".

3.Begin speaking after you hear the beep.

4.Release the button when you finish your announcement.

NOTE: If you choose not to record an outgoing announcement, a default announcement plays instead. To return to the default announcement after you have recorded your own outgoing announcement, press the ANNOUNCE 1 or 2 button and release it when you hear the beep. Or, press the DELETE button while the announcement is playing.

Sample Outgoing Announcement

1) Sample Single Mailbox Outgoing Announcement

Hi, this is (use your name here), I can’t answer the phone right now, so please leave your name, number and a brief message after the tone, and I’ll get back to you. Thanks.

NOTE: The maximum recording time for the outgoing announcement is 2 minutes.

14

2) Sample Multi-Mailbox Outgoing Announcement

Hi, this is (use your name here), We can’t answer the phone right now, so please press 1 to direct your message to (name 1), press 2 to direct your message to (name 2), press 3 to direct your message to (name 3). Leave your name, number and a brief message after the tone, and we’ll get back to you soon. Thanks.

Reviewing and Choosing the Announcement

Press and release the ANNOUNCE 1 button to review and select this one as your outgoing announcement. Or, press and release the ANNOUNCE 2 button to review and select this one as your outgoing announcement.

Audible Quick Setup Guide

If you need additional assistance on how the buttons function, press the REV button in standby mode and follow the voice instructions.

Programming the Telephone

The handset menu gives you access to all of the built-in features. Press the MENU button to display the first menu PHONE BOOK, and press 6and 5buttons to navigate to the desired menu option. Press the SELECT button to activate a menu option. For details on programming, refer to the applicable section.

During programming, you may press the *EXIT button at any time to exit the menu and keep the previous setting.

PHONE BOOK

Enter and retrieve up to 50 names and phone

 

numbers, each can be assigned a distinctive ringer

 

tone and image.

ROOM MONITOR

Allows you to monitor any room in your house with

 

the accessory handsets.

INTERCOM

Talk between handsets or use to page each other.

ANSWERER

Remotely access the answering system to adjust

 

the rings to answer, security code and new message

 

alert settings.

15

CALL RECORDS Review Caller ID data; select and dial from the Caller ID data or from the Redial list which contains the last 3 phone numbers dialed.

SOUND SETTING Record ringer tone from microphone, headset or any audio player; select main ringer tone or set key tone.

PHONE SETTING Set display language, set area code, register the handset to the base unit, name the handset or reset to default setting.

DISPLAY SETTING Choose a preset and downloaded images to be wallpaper of the idle display or set the contrast and color scheme.

Phone Setting

There are seven programmable menus available: Language, Area Code, Intercom Auto Answer, Handset Name, Registration, Deregistration and Default Setting.

LANGUAGE

AREA CODE REGISTRATION HANDSET NAME DEREGISTRATION

PHONE SETTING

1.Make sure your phone is OFF (not in talk mode).

2.Press the MENU button and use the 6or 5button to scroll to PHONE SETTING.

3.Press the SELECT button to enter the menu.

Language

This menu allows you to change the language of the display prompts. From the PHONE SETTING menu;

ENGLISH

FRANCAIS

ESPANOL

SET LANGUAGE

1.Use the 6or 5 button to scroll to LANGUAGE.

2.Press the SELECT button to enter the menu.

3.Use the 6or 5 button to scroll to the desired language. The default is ENGLISH.

4.Press the SELECT button to save your selection. You will hear a confirmation tone.

16

Area Code

If you enter your local 3-digit area code in the area code menu, your local area code does not display on the Caller ID (CID) list. Instead, you only see the local 7-digit number. Calls received from outside your local area code will display the full 10-digits. From the PHONE SETTING menu;

— —

SET AREA CODE

1.Use the 6or 5 button to scroll to SET AREA CODE.

2.Press the SELECT button to enter the menu.

3.Use the number keys to enter your 3 digit area code. “ - - - “ is the default setting.

4.Press the SELECT button to save your selection. You will hear a confirmation tone.

NOTE: To restore the default setting to “---”, press and release the FLASH/DELETE button when SET AREA CODE shows on the display.

Registration

Your handset is pre-registered and ready to use. It is not recommended that handset be registered again unless absolutely necessary.

From the PHONE SETTING menu;

 

 

 

1. Use the 6or 5 button to scroll to REGISTRATION.

NO

 

 

YES

2.

Press the SELECT button to enter the menu.

 

 

3.

Use the 6or 5 button to scroll to NO or YES. The default

 

 

 

is NO.

 

REGISTRATION

 

4.

If you select YES, press the SELECT button to confirm.

 

 

 

 

HOLD BASE PAGE WAIT FOR BEEP shows on the display.

 

5.

Press and hold the PAGE button on base unit until you

 

 

 

 

hear a long tone at the handset. HANDSET X REGISTERED

 

 

 

 

shows in the handset display, where X is the handset

 

 

 

 

number. You will hear a confirmation tone.

NOTE: After you have registered one handset, wait 10 seconds before registering another handset to ensure successful registration.

17

Handset Name

This menu allows you to enter a name for the handset, which displays on the idle screen.

From the PHONE SETTING menu;

 

1.

Use the 6or 5 button to scroll to HANDSET NAME.

DANIEL

2.

Press the SELECT button to enter the menu.

 

 

HANDSET NAME

3.Use the number keys to enter a name (up to 15 characters). More than one letter is stored in each of the number keys. For example, to enter Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L. Wait for 1 second, press the 5 key 3 times for the second letter L, and press the 1 key to insert a space between the first and last name. Press the 7 key 4 times for the letter S; press the 6 key once for the letter M; press the 4 key 3 times for the letter I. Press the 8 key for the letter T; press the 4 key twice for the letter H.

4.Press the SELECT button to save your selection. You will hear a confirmation tone.

NOTE: If you make a mistake, use the FLASH/DELETE button to backspace and delete one character at a time.

Deregistration

Deregistration cancels registration. During the deregistration process, keep the handset near the base.

From the PHONE SETTING menu;

NO

YES

DEREGISTRATION

1.Use the 6or 5 button to scroll to DEREGISTRATION.

2.Press the SELECT button to enter the menu.

3.Use the 6or 5 button to scroll to NO or YES. The default is NO.

WARNING: It is not recommended that a handset be deregistered unless absolutely necessary because once a handset is deregistered, that handset’s telephone features cannot be used until the handset is re-registered.

18

NO

4. Select NO, if you do not want to deregister.

YES

5.

If you select YES, press the SELECT button to confirm.

 

 

 

 

CONFIRM?

 

MOVE NEAR TO BASE displays for 2 seconds, then

 

 

 

 

NO YES CONFIRM? shows on the display.

 

DEREGISTRATION

 

 

 

 

6.

Use the 6or 5 button to scroll to NO or YES.

 

 

 

 

The default is YES.

 

 

 

7.

If you select YES, press the SELECT button to confirm.

 

 

 

 

DE-REGISTER . . . shows on the display followed by a

 

 

 

 

confirmation tone. Then, HANDSET X DEREGISTERED

 

 

 

 

shows on the display to confirm that the handset is

 

 

 

 

deregistered.

NOTE: When you complete the deregistration process, HANDSET NEEDS REGISTRATION shows on the display. To use the handset, you must register the handset.

Global De-Registration

If one or more handsets become lost, you should de-register all handsets to ensure proper system operation. Follow the steps below to deregister all handsets at the same time.

WARNING: It is not recommended that a handset be deregistered unless absolutely necessary because once a handset is deregistered, that handset’s telephone features cannot be used until the handset is re-registered.

NOTE: Before starting global deregistration procedure, let all handsets set idle for 20 seconds.

1.Press and hold the PAGE button on the base until the CHARGE/IN USE indicator on the base flashes.

2.Press and hold the PAGE button on the base again until the CHARGE/IN USE indicator on the base flashes rapidly.

3.Press and release the PAGE button on the base once. All handsets are deregistered and HANDSET NEEDS REGISTRATION shows on their displays.

19

Loading...
+ 43 hidden pages