GarrettCom 6K32FR, 6K32FRC, 6K32F, 6K32FC User Manual

0 (0)
GarrettCom 6K32FR, 6K32FRC, 6K32F, 6K32FC User Manual

Corporate Headquarters

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539-7437

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com

email support@garrettcom.com

Magnum 6K32F, 6K32FR, 6K32FC &

6K32FRC

www . GarrettCom . com

Industrial Managed Switch

Installation and User Guide

Hardware User Manual

www . GarrettCom . com

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

Magnum6K32F, 6K32FR, 6K32FC & 6K32FRC

Managed Switch Hardware

Installation and User Guide

Part #: 84-00103Z (Rev. A)

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum, Personal Switch, S-Ring, Link-Loss-Learn, Converter Switch and Convenient Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.

GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice.

Important: The Magnum 6K32F Series Managed Switch contains no user serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. If problems are experienced with Magnum 6K32F Series of Switch products, consult Section 6, Troubleshooting, of this User Guide.

Copyright © 2008 GarrettCom, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from

GarrettCom, Inc.

Printed in the United States of America.

www . GarrettCom . com

i

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below: GarrettCom, Inc.

47823Westinghouse Dr. Fremont, CA 94539-7437

Phone (510) 438-9071

Fax (510) 438-9072

Website: http://www.GarrettCom.com email support@garrettcom.com

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer's instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Canadian Emission

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil respecte toutes les exigences du Réglement sur le matériel du Canada. Cet appareil est Classe A.

www . GarrettCom . com

ii

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

TABLE OF CONTENTS..........................................................................

Page

1.0

SPECIFICATIONS................................................................................

1

1.1

Technical Specifications.......................................................................

1

1.2

Ordering Information ...........................................................................

4

2.0

INTRODUCTION..................................................................................

9

2.1

Inspecting the Package and Product.....................................................

9

2.2

Product Description - Magnum 6K32FC/FRC Managed Switch.......

10

2.2.1a

Magnum 6K32F/FR Managed Switch Chassis ..........................

12

2.2.2

Eight-port SFF fiber modules (6KP8-MTRJ, 6KP8-MLC) .......

13

2.2.3 Eight-Port Copper Module, 6KP8-RJ45 (MDIX) ..............................

14

2.2.3a

PoE(Power Inside), PI6KP8-45RJ (MDIX), 8-port 10/100Mb..15

2.2.3b PoE(Power Pass-through) P6KP8-RJ45 (MDIX) 8-port ...........

15

2.2.4

Six-Port “4 + 2”Combo Modules fiber ST or SC.......................

16

2.2.5

Four-Port 10 Mb mm Fiber ST Modules..................................

17

2.2.6

Gigabit (1000Mbps) port modules .............................................

17

2.2.7

Packet Prioritization, 802.1p QOS .............................................

18

2.2.8

Frame Buffering and Flow Control ............................................

18

2.2.9

Managed Network Software 6K32F Series................................

19

2.3

Features and Benefits .........................................................................

20

2.4

Applications .......................................................................................

21

3.0

INSTALLATION ................................................................................

26

3.1

Locating Magnum 6K32F Switches...................................................

26

3.2

Connecting Ethernet Media................................................................

27

3.2.1

Connecting Fiber Optic ST-type, “twist-lock” ...........................

27

3.2.2

Connecting Fiber Optic SC-type, "Snap-In" ..............................

28

3.2.3

Connecting Single-Mode Fiber Optic ........................................

28

3.2.4

Connecting Twisted Pair (RJ-45,CAT3, CAT5) ........................

28

3.2.5

Connecting Twisted Pair (CAT-5e or better) .............................

29

3.2.6

Gigabit SFP (Small Form-factor Pluggable) Transceivers.........

30

3.2.7

Power Budget Calculations 6K32F Series PM’s .......................

31

3.3

Table-Top or Shelf Mounting.............................................................

33

3.3.1

Rack-mounting (for 19” RETMA)6K32F & 6K32FC’s ............

33

3.3.2 Rack-mounting, Reverse version of the Magnum 6K32F’s..............

34

3.4

Powering the Magnum 6K32F Series Managed Switch.....................

34

3.4.1

Alarm Contacts for monitoring internal power Traps.................

35

3.5

6K32F Series Port Module (6KPM) Installation................................

36

3.5.1

Preparation for Installing and Removing 6KPMs......................

36

3.5.2

Installing 6KPM Cards in the 6K32F Series ..............................

38

3.5.3

Removing 6KPM Cards .............................................................

40

3.6

Connecting the Console Terminal to 6K32F Series ...........................

42

3.6.1

RS-232 (DB-9) Console Com port (Serial port) pin...................

42

4.0

OPERATION........................................................................................

44

4.1

Switching Functionality .....................................................................

44

4.2

Status LEDs........................................................................................

45

4.3

Auto-Cross (MDIX)Auto-neg for 10/100Mbps RJ-45 ports..............

45

www . GarrettCom . com

iii

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

4.4

Flow-control, IEEE 802.3x standard..................................................

46

5.0 6K32F SERIES MANAGED SWITCH PORT MODULES.............

47

5.1

Inspecting the Package and Product...................................................

47

5.2

6KPM Module Description ................................................................

47

5.2.1

6KP6-RJMST multi-mode FX-ST “twist lock” Module ............

48

5.2.1a

6KP6-RJ10ST multi-mode FX-ST “twist lock” Combo ............

48

5.2.1b

6KP4-F10ST multi-mode FX-ST “twist lock” Module.............

49

5.2.1c

6KP4-FLSTFX multi-mode FX-ST “twist lock” Module .........

49

5.2.2.

6KP6-RJMSC multi-mode FX-SC “snap-in” Module ..............

50

5.2.3

6KP6-RJSSC Mbps single-mode FX-SC-type, “snap-in”.........

50

5.2.4

6KP6-RJSSCL FX-SC-type, “snap-in” connector ....................

51

5.2.4a

6KP6-RJ10ST FL-ST-type, “twist-lock” connector...................

51

5.2.5

6KP8-MTRJJ Small-Form-factor...............................................

52

5.2.5a

6KP6-MT10STmode FX Factor ................................................

52

5.2.6

6KP8-45MT MTRJ Small-Form-Factor.....................................

53

5.2.7

6KP8-MLC LC connector Small- ..............................................

53

5.2.8

6KP8-45LC 10/100 Mbps RJ-45 Connector ..............................

54

5.2.9

6KP8-RJ45 (Twisted Pair), 10/100Mb 8-Port...........................

54

5.2.10a. PoE (Power Pass-through)P6KP8V-RJ45 (MDIX) ...................

55

5.2.10b. PoE(Power Inside), model PI6KP8-45RJ (MDIX)....................

56

5.2.11

6KP8-45-2MT MTRJ Small-Form-Factor ................................

57

5.2.11a 6KP8-45-2LC single-mode FX , LC Small-Form-Factor ..........

58

5.2.12

GBIC-SXSC Gigabit fiber(1000Mb), multi-mode SC ..............

58

5.2.12a GBPM-2OTX (Two Gigabit option)..........................................

59

5.2.12b GBIC-LXSC Gigabit fiber (1000Mb), multi-mode SC ............

59

5.2.13

6KM-BLNK ...............................................................................

60

6.0

TROUBLESHOOTING.......................................................................

60

6.1

Before Calling for Assistance.............................................................

61

6.2

When Calling for Assistance..............................................................

61

6.3

Return Material Authorization (RMA) Procedure..............................

62

6.4

Shipping and Packaging Information .................................................

63

APPENDIX A: WARRANTY INFORMATION .........................................

63

APPENDIX B : INTERNAL DC POWER SUPPLY OPTIONS.................

64

APPENDIX C: INTERNAL DC DUAL-SOURCE POWER OPTION ......

67

Revisions

Rev A 05/08 : Initial release of the Magnum 6K32F Series manual.

www . GarrettCom . com

iv

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

The Magnum Line

INDUSTRIAL NETWORKING PRODUCTS

"DESIGNED AND MANUFACTURED IN THE USA"

OVERVIEW

GarrettCom, Inc. offers the premium-quality Magnumline of INDUSTRIAL connectivity products with industry-standard functionality and built-in fiber configurability. Magnum products are designed for use in demanding Industrial Grade, Carrier Class, POWER UTILITY and OEM applications where reliability is a primary consideration.

6K-Series Managed Field Switches, Gigabit, 100 and 10 Mbps, fiber and copper ports, mix-and match. Features SFF fiber and DC power in 1U units.

DX-Series Serial Device Routers, Ethernet and Serial

4K-Series Switches, 100 and 10 Mbps, copper ports with optional fiber port, with auto-negotiating

full switching performance.

Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports, mixed-speed and mixed-media

types, full switching performance.

mP62 and P62F “Outdoor” Ethernet SwitchES, for temperature uncontrolled locations, 6 10/100 and 2 100Mb fiber ports, can be connected in strings

Mixed-Media Fiber Hub, 16-port, 10/100 auto-sensing

Dual Speed 8-port and 16-port, 10/100 auto-sensing HUBS

Personal Switches, 10/100/1000Mb

8 port dual-speed, Auto-negotiable with fiber option

Personal Hubs, 100Mb or 10/100Mb 8-port, with 2 switched ports (1 fiber built in)

Personal Hubs, 10Mb series 8-port + AUI, stackable to 5 high, + optional BNC of fiber port 8 or 9- port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.

Media Converters, 10Mb and 100Mb series, All media combinations, incl. fiber ST, SC, mm.,

single mode

The “X-line” of configurable MiXed Media products:

Stackable Concentrators, SNMP optional, 13-Ports

Mini-Concentrators, 7 Ports, Repeaters, 2-Ports

Repeater Port Modules (RPMs), 6 types for Ethernet media

COAX Transceivers, 10Mb series

APR, 07

www . GarrettCom . com

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

1.0SPECIFICATIONS

1.1Technical Specifications

Performance

Filtering / Forwarding Rate: Ethernet:14,880 pps

Fast Ethernet: 148,800 pps Gigabit Ethernet: 1,488,000 pps

Switching Processing Type: Store and Forward with IEEE 802.3x fullduplex flow -control, non-blocking

Data Rate: 10Mbps,100Mbps and 1000Mbps

Address Table Capacity: 4K node, self-learning with address aging Packet buffer size : 240KB for 10/100 and 120KB for 1000Mb

Latency: 6 μs + packet time (TX – TX, TX – FX, FX – FX, TX - G, G - G) Throughput with 16 10/100 and 4 Glink max- 8.33M pps (Transmit)

Back plane- 2.66Gb/s per slot

Network Standards and Compliance

Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,

IEEE 802.3u: 100Base-TX, 100BASE-FX

IEEE 802.3z: 1000BASE-X Ethernet(Auto-negotiation)

IEEE 802.3ab: 1000BASE-X Ethernet

IEEE 802.1p: Priority protocol

IEEE 802.1d: Spanning tree protocol

IEEE 802.1w: Rapid Spanning tree protocol

IEEE 802.1q: VLAN Tagging

IEEE 802.3x: Flow Control

IEEE 802.3ad: Link Aggregation (Trunking)

IEEE 802.1x: Port based Network access control

IEEE 802.3af: Power over Ethernet(PoE)

 

 

Maximum 10 Mbps Ethernet Segment Lengths

 

 

Unshielded twisted pair

-

100 m (328 ft)

Shielded twisted pair

-

150 m (492 ft)

10BASE-FL multi-mode fiber optic

-

2 km (6,562 ft)

10BASE-FL single-mode fiber optic

-

10 km (32,810 ft)

Maximum Standard Fast Ethernet Segment Lengths:

10BASE-T (CAT 3, 4, 5 UTP)

- 100 m (328 ft)

100BASE-TX (CAT 5 UTP)

- 100 m (328 ft)

Shielded twisted pair

-

150 m (492 ft)

100BASE-FX, half-duplex, multi-mode

- 412 m (1350 ft)

100BASE-FX, full-duplex, multi-mode

- 2.0 km (6,562 ft)

100BASE-FX, half-duplex, single-mode

- 412 m (1350 ft)

100BASE-FX, full-duplex, single-mode

- 20.0 km (65,620 ft)

100BASE-FX, full-duplex, Long Reach

- 40.0 km (131,240 ft)

www . GarrettCom . com

1

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

Maximum Standard Gigabit Ethernet Segment Lengths:

 

1000BASE-T (CAT5E or higher is recommended)

- 100 m

1000BASE-SX, full-duplex, multi-mode(62.5μm cable)

- 220m

1000BASE-SX, full-duplex, multi-mode(50μm cable)

- 550m

1000BASE-LX, full-duplex, single-mode(9μm cable)

-5Km

Fiber connector types supported:

ST-type (twist-lock)

SC-type (snap-in)

MTRJ-type Small Form Factor (SFF)

LC-type Small Form Factor (SFF)

GBIC modules

LEDs: Per Port

LK: Steady ON when media link is operational ACT: ON with receiver port activity FDX/HDX: ON = Full-Duplex Mode

OFF = Half-Duplex Mode 100/10: ON = 100Mbps speed

OFF = 10 Mbps

Operating Environment

UL 60950 “Component Parts” temp. ratings: 140° F (60°C) IEC 60068 “Type Test” ratings:- -40°to 185°F (-40°to 85°C) Ambient Relative Humidity: 5% to 95% (non-condensing) Altitude: -200 to 13,000 ft. (-60 to 4000m)

Conformal Coating (Humidity Protection) option: Request quote

Packaging

Enclosure: Rugged High strength metal. Suitable for stand-alone or rack-mounting

Dimensions: 1.70in. H x 17.0in. W x 9.0in. D 4.32cm H x 43.2cm W x 22.9cm D

Cooling method: Fan cooled, @ 25 cfm ea.

Management Console connector

DB-9 for RS-232 “ null-modem“ cable (sometimes called an X-modem cable)

Power Supply (Internal)

AC Power Connector: IEC-type, male recessed at rear of chassis,

with adjacent manual ON-OFF switch (optional if no Alarms Cont.) Input Voltage: 100 to 240 VAC (auto-ranging)

Input Frequency: 47 to 63 Hz (auto-ranging)

Power Consumption: 60 watts max (fully-loaded with fiber modules) 30 watts max (fully-loaded copper only modules)

Fuse required for replacement- 1 Amp

DC Power Supply (Options)

-48VDC Power Input Voltage : -36 to -70 VDC Fuse Required – 2 Amps

24VDC Power Input Voltage : 20 to 40VDC

www . GarrettCom . com

2

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

Fuse Required – 3 Amps

125VDC and 100VDC Input Voltage : 88 to 300VDC Fuse Required – 1 Amp

Std. Terminal Block : “ -, GND, + ”

Power Consumption: same as for AC models, see above

Warning- All the fuse replacement must be replaced with same value.

For (Optional) DC internal power supplies at –48VDC, 24VDC and 125VDC, including Dual Source options (for continuity of operation when either of the DC input sources are interrupted), see Appendices B and C.

Cooling Method-

6K32F/ 6K32FR(Reverse)- Fan cooled (3 fans inside)

6K32FC / 6K32FRC(Reverse)- Convection cooled (No fans) Static Thermal design techniques

Relay Alarm Contact (Optional)

The Alarm Contact option is offered as a configuration option. The alarms can be initiated through two normally closed Form-C contacts, one loss of power alarm and one software alarm through user selectable software traps.

Per-port MDI or MDIX on RJ-45

The copper daughter board has MDI-MDIX Auto-crossover on all the RJ-45 ports which eliminates the use of cross-over cable between the devices. Also port-specific user settings (such as FDX or HDX, copper 10/100 speed) can be fixed using software commands.

Agency Approvals

UL listed (UL60950), cUL, CE, Emissions meet FCC Part 15, Class A NEBS L3 and ETSI Compliant, NEMA TS-2 for traffic control

IEEE 1613 Classs 2 Environmental Standard for Electric Power Substations. See also Note for Power Substations in Section 3.2.4, 3.6.1, and 5.2.9

IEC61850 EMC and Operating Conditions Class C for Power Substations

Warranty: Three years, return to factory

Made in USA

For a Configuration Guide, see the GarrettCom web site at

http://www.garrettcom.com/techsupport/insertion_guides/6k32fcg.pdf (6K32F / FR)

http://www.garrettcom.com/techsupport/insertion_guides/6k32fccg.pdf (6K32FC / FRC)

Email mktg@GarrettCom.com for additional details.

www . GarrettCom . com

3

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

1.2Ordering Information

Magnum Managed Switch

MODEL DESCRIPTION

Magnum 6K32F or 6K32FR (Reverse model) 32-10/100 RJ-45 ports or 8 Gigabit ports managed switch with four modular slots which may be configured with a selection of 10/100/1000Mb fiber and copper connector types, max. 32 ports 10/100 or 8 ports Gigabit max., or combination.

Magnum 6K32F-48VDC:Same as 6K32F except power input is –48VDC Magnum 6K32F-24VDC:Same as 6K32F except power input is 24VDC Magnum 6K32F-125VDC:Same as 6K32F except power input is 125VDC

Magnum 6K32FR-48VDC:Same as 6K32F except reverse and power input is –48VDC Magnum 6K32FR-24VDC:Same as 6K32F except reverse and power input is 24VDC Magnum 6K32FR-125VDC:Same as 6K32F except reverse and power input is 125VDC

Magnum 6K32FC or 6K32FRC (Reverse model)- Convection cooled (no fans) managed switch, with four modular slots which may be configured with a selection of 10/100/1000Mb fiber and/or copper connector types, max. 32 ports 10/100 fiber or copper or 8 Gigabit ports.

Magnum 6K32FC-48VDC:Same as 6K32FC except power input is –48VDC Magnum 6K32FC-24VDC:Same as 6K32FC except power input is 24VDC Magnum 6K32FC-125VDC:Same as 6K32FC except power input is 125VDC

Magnum 6K32FRC-48VDC:Same as 6K32FC except reverse &power input is –48VDC Magnum 6K32FRC-24VDC:Same as 6K32FC except reverse &power input is 24VDC Magnum 6K32FRC-125VDC:Same as 6K32FC except reverse &power input is 125VDC

Configuration Options:

Each Magnum 6K32F Series base unit has four configurable port modules slot to be configured with any one of the port modules listed below:

Magnum 6K32F Series Port Modules (all modules include front panel) 6KP8-RJ45 TP Module, w/eight 10/100Mbps auto-negotiating RJ-45 ports 6KP4-F10ST “2+2” 10Mb Fiber module, w/ four 10Mb 2km FL ST connectors 6KP4-FXSC “2+2” 100Mb Fiber module, w/ four 100Mb 2km FX SC connectors 6KP4-FXST “2+2” ST Fiber module, w/ s, four 100Mb 2km FX ST connectors 6KP4-FLSTFX “2+2” ST Fiber module, w/ two 100Mb and two 10Mb ports, 2km 6KP6-RJMST “4+2” module, w/four RJ-45 ports and two 2km mm FX SC’s 6KP6-RJMSC “4+2” module, w/four RJ-45 ports and two 2km mm FX ST‘s 6KP6-RJSSC “4+2” module, w/four RJ-45 ports and two 20km Sgl.m FX SC’s 6KP6-RJSSCL “4+2” module, w/four RJ-45 ports and two 40km Sgl.m FX SC’s

www . GarrettCom . com

4

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

6KP8-MTRJ 6KP8-MLC 6KP8-SLC

6KP8-45MT 6KP8-45MLC

6KP8-45SLC 6KP6-MT10ST 6KP6-RJ10ST 6KP8-45-2MT 6KP8-45-2SLC

Gigabit Modules,

6KP2-2GSFP

SFF Fiber module, w/eight 100Mb mm FX MT-RJ connectors SFF Fiber module, w/eight 100Mbps mm FX LC connectors SFF Fiber module, w/eight 100Mbps sgl-m FX LC connectors

“4+4” module, w/four RJ-45 ports and four 2km mm FX MT-RJ’s “4+4” module, w/four RJ-45 ports and four 2km mm LC connectors

“4+4” module, w/four RJ-45 ports and four 15km Sm LC connectors “4+2” module, w/four MTRJ ports and two 10Mb 2km FL ST’s “4+2” module, w/four RJ-45 ports and two 10Mb 2km FL ST ‘s “6+2” module, w/six RJ-45 ports and two 2km mm MTRJ connectors

“6+2” module, w/six RJ-45 ports and two 100Mb 15km sgl. mode FX LC connectors

fixed ports, using Small form factor (SFP) transceivers (all modules include front panel)

two port in one slot Gigabit 6K module, uses one 6K slot and provides two SFP Gb Fiber (1000BASE-SX Multi-mode) ports

6KP2-1GCU1SFP two port in one slot Gigabit 6K module, uses one 6K slot and provides one SFP Gb Fiber (1000BASE-SX Multi-mode) port and one Gb Copper (1000BASE-RJ45 Auto-negotiating) port

6KP1-1GSFP one port in one slot Gigabit 6K module, uses one 6K slot and provides one SFP Gb Fiber (1000BASE-SX Multi-mode) port

6KP1-1GCU one port in one slot Gigabit 6K module, uses one 6K slot and provides one Gb Copper (1000 BASE-RJ45 Auto-negotiating) port

Gigabit Options (Modules using GBIC) (all modules include front panel)

6KP5-G4RJ “G+4” module, with one GBIC open transceiver and four 10/100 RJ-45 connectors

6KP3-G2SC “G+2” module, with one GBIC transceiver and two 100Mb 2km FX SC fiber ports connectors

GBPM-2OTX Two port Gigabit module provides two GBIC open transceiver ports for a user-selectable GBIC transceiver module

GBPM-COTX One slot Gigabit 6K module provides one GBIC open transceiver port for a user-selectable GBIC transceiver module

GBIC-SXSC GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-SX port with multimode SC fiber connector

GBIC-LXSC10 GBIC transceiver module for use in GBPM-xOTX. One 1000BASELX/LH port with 1310nm single mode SC(10km) fiber connector

GBIC-LXSC25 GBIC transceiver module for use in GBPM-xOTX. One 1000BASELX/LH port with 1310nm single mode SC(25km) fiber connector

GBIC-ZXSC40 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-ZX port with 1550nm, single mode SC(40km) fiber connector

GBIC-ZXSC70 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-ZX port with 1550nm, single. mode SC(70km) fiber connector.

GBIC-ZXSC120 GBIC transceiver module for use in GBPM-xOTX. One 1000BASE-ZX port with 1550nm, single. mode SC(120km) fiber connector.

www . GarrettCom . com

5

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

GBIC-TP GBIC transceiver module for use in GBPM-xOTX. One 802.3ab 1000BASE-T port with RJ-45 connector

Modules with Gb, not using GBICs (all modules include front panel)

6KP5-1CU4RJ “G+4” module, with one GBIC copper (Auto-negotiating) transceiver and four 10/100 RJ-45 connectors

6KP5-1CU4MT “G+4” module, with one GBIC copper (Auto-negotiating) transceiver and four 100Mb MTRJ Fx-Multi-mode connectors

6KP3-1CU2FXT “G+2” module, with one GBIC copper (Auto-negotiating) transceiver and four 100Mb ST Fx-Multi-mode connectors

6KP2-1CU1SX two-port in one slot Gigabit 6K module, uses one 6K slot and provides one Gb Fiber SXSC (1000BASE-SX Multi-mode) port and one Gb Copper (1000BASE-RJ45 Auto-negotiating) port

6KP2-2GSX two-port in one slot Gigabit 6K module, uses one 6K slot and provides two Gb Fiber SXSC (1000BASE-SX Multi-mode) ports

6KP2-2GCU two-port in one slot Gigabit 6K module, uses one 6K slot and provides two Gb Copper (1000BASE-RJ45 Auto-negotiating) ports

6KM-BLNK Blank cover for one 6K32F Series module slot opening in a Magnum 6K32F Series chassis

CONSOLE CBL Industry standard serial cable, DB-9 connectors for RS-232 “ nullmodem “ connection (sometimes called an Xmodem cable), used to connect a PC or a character terminal to the Management port.

CONSOLE USB Console attachment cable, serial to USB, cable with one DB9 for the managed Switch and a USB interface for the USB connector to a PC.

MNS-6K License(Management software)- Preloaded with the latest firmware, license costs included with each 6K base unit.

www . GarrettCom . com

6

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

6K32F Series PoE Modules with 48VDC Pass-Through

Configuration options: All module slots of 6K32F Series switch with 48VDC power input may be configured with a PoE Module (typical configuration has slot A loaded first with PoE module)

P6KP8-RJ45 8 port PoE module for 6Ks with 48vdc PS, w/eight PoE power source 10/100 auto-negotiating auto cross RJ-45 ports.

P6KP8-45RJ “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 10/100 auto-negotiating auto cross RJ-45 ports

P6KP8-45MT “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 2km mm FX MTRJ connectors

P6KP8-45MLC “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 2km mm FX LC connectors

P6KP8-45SLC “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 15km sm FX LC connectors

P6KP8-45-2MT “6+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two normal RJ-45 10/100 ports +two100 Mb 2km mm FX MTRJ connectors

P6KP8-452SLC “6+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 15km Sm FX LC connectors

P6KP6-RJMST “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 2km mm FX ST connectors

P6KP6-RJMSC “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 2km mm FX SC connectors

P6KP6-RJSSC “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 20km sm FX SC connectors

P6KP6-RJSSCL “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 40km sm FX SC connectors

P6KP6-RJ10ST “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 10 Mb 2km sm FL ST connectors

www . GarrettCom . com

7

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

6K32F Series PoE Modules with 48VDC Power Inside

NOTE: For configuring in 6K Switches having AC /125VDC power input

Configuration options: only one A, B, C or D (left to right) module slot of 6K32F Series switch with 48VDC power input may be configured with a PoE Module (typical configuration has slot A loaded with PoE module)

6KAC-PoE-PS Power supply for PoE to 4 ports, 60 watts, mounts inside of a full-width rack-mount 6K switch with AC power input.

6K125VDC-PoE-PS Power supply for PoE to 4 ports, 60 watts, mounts inside of a fullwidth rack-mount 6K switch with 125VDC power input.

PI6KP8-45RJ “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 10/100 auto-negotiating auto cross RJ-45 ports

PI6KP8-45MT “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 2km mm FX MTRJ connectors

PI6KP8-45MLC “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 2km mm FX LC connectors

PI6KP8-45SLC “4+4” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 15km sm FX LC connectors

PI6KP8-45-2MT “6+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two normal RJ-45 10/100 ports +two100 Mb 2km mm FX MTRJ connectors

PI6KP8-452SLC “6+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and four 100 Mb 15km sm FX LC connectors

PI6KP6-RJMST “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 2km mm FX ST connectors

PI6KP6-RJMSC “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 2km mm FX SC connectors

PI6KP6-RJSSC “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 20km sm FX SC connectors

PI6KP6-RJSSCL“4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 100 Mb 40km sm FX SC connectors

PI6KP6-RJ10ST “4+2” port PoE module for 6Ks with 48vdc PS, w/four PoE power source and two 10 Mb 2km sm FL ST connectors

GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice.

www . GarrettCom . com

8

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

2.0Introduction

2.1Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this

product; notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect the contents of this package for any signs of damage and ensure that the items listed below are included.

This package should contain:

1Magnum 6K32F, 6K32FR, 6K32FC or 6K32FRC Managed Switch, base unit (configured with user-selected port module option in modular slot)

1 AC Power Cord (U.S. and other 115 VAC only)

1 Set of metal “Ears” for 19” rack mounting

1 Installation and User Guide (this manual)

Remove the items from the shipping container. Be sure to keep the shipping container should you need to re-ship the unit at a later date.

In the event there are items missing or damaged, contact the party from whom you purchased the product. If the unit needs to be returned, please use the original shipping container if possible. Refer to Section 6, Troubleshooting, for specific return procedures.

www . GarrettCom . com

9

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

2.2Product Description –

Magnum 6K32FC / FRC (Convection cooled - No-fans) Managed

Switch

All of the Magnum 6K32F Series of Ethernet Switches comply with IEC61850 and IEEE1613 Utility Automation and other industry standards.

The Magnum 6K32FC/FRC Managed Switches are specially designed with convection cooling thermal design techniques to minimize heat build up providing an efficient, economical, highly reliable, long lived and secure Ethernet solution for heavy duty Industrial, Power sub-stations and temp-uncontrolled outdoor applications.

Specially designed and enclosed in a standard and “Reverse” aluminum case, the 6K32FC/FRC is proudly offered with modularity, port density (up to 32 ports max.) and security in a 1U rack-mount package.

The Magnum 6K32F Series are derived from the highly successful 6K managed switch family, with additional modularity in all 4 slots providing increased configurability provided by the numerous 6KP modules available.

Figure 2.2.1a: A typical 6K32FC Switch front view, 4 RJ-45 10/100 ports, 2 ST 10Mb FL ports, 8 ST 100Mb FX ports and 2 RJ45 Gigabit ports.

The Magnum 6K32F Series has the flexibility to configure up to thirty two 100Mb Fiber ports, or thirty two 10/100Mb Copper ports, or eight Gigabit(1000Mb) ports providing a combination of options to handle high and low bandwidth applications efficiently. The various Power over Ethernet (PoE) modules add the advantage for Magnum 6K32F Series users of providing secure and economical solutions for critical remote applications.

The preloaded robust and intuitive MNS-6K Managed Network firmware with multiple secured managed features is able to handle industry-standard IEEE 802.1p QOS prioritization and non-blocking wire speed on all ports. It provides high performance

www . GarrettCom . com

10

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

switching services for both “smooth” streaming and “bursty” data traffic. For redundant LANs it offers S-ring, RS-Ring, Link-Loss-Learn, STP and RSTP. Optional Security features include SNMPv3, SSL/SSH, 802.1X, TACACS+, Port Security, and Tagged VLANs as well as a secure, user friendly web based option. IGMP Snooping and IGMP-L2 features provide most IGMP Layer 3 functions for multicast traffic with Magnum 6K-Switches thus enabling an economical solution without Routers or Layer 3 switches for streaming video applications.

See MNS-6K materials for further details about management software. http://www.garrettcom.com/techsupport/software/userguides/mns6k_webmanual.p df (web)

http://www.garrettcom.com/techsupport/software/userguides/mns6k_CLI.pdf (CLI)

Evolving mixed-media requirements for 10Mb and 100Mb fiber, copper, and 1000Mb Gigabit Ethernet can be simply and reliably handled by the Magnum 6K32F Series products.

The port flexibility feature is achieved using a large family of 6K modules with various copper and fiber capabilities built-in. High fiber port density is achieved using Small Form Factor LC or MTRJ connectors and multimode and single-mode fiber networks from 2 to over 100km are accommodated. Each module can support up to 8 ports of fiber or RJ-45 copper connectors as well as various fiber and copper combinations. Fixed one and two Gigabit fiber and copper modules are available along with modules for use with GBIC and SFP fiber and copper transceivers making this product adaptable to almost any network need. Modules are factory configured in a base chassis (or may be changed in the field by trained technicians) to adapt the unit to the user’s specific Ethernet media requirements.

The strong aluminum case and wide selection of power-input options including -48VDC, 24VDC, 125/110 VDC, 250VDC and universal 110/240VAC target the Magnum 6K32F Series for heavy-duty applications. The chassis rack mounting style of the 6K32FR / FRC is “Reverse” (with the ports and LEDs and the power-input and the management console connector all in the rear and a duplicate set of LEDs in the front). Rack widths accommodated include standard 19” RETMA, ETSI, and 23” Telco. The

www . GarrettCom . com

11

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

AC, and –48VDC power input options are designed for Telco environments, while the 24VDC is designed for Industrial/Control Room applications. The 125 & 250VDC versions are for power sub stations applications.

Designed primarily for use in harsh, un-controlled temperature industrial applications, the Magnum 6K32FC / FRC provides secure, high performance plug-and- play hardware operation, 802.1p packet prioritization in hardware, and industry-standard managed networks software functionality with plenty of secure and remote monitoring features, all in convenient 1U rack-mount packages.

2.2.1a Magnum 6K32F / FR (Fan cooled) Managed Switch Chassis

The high port density and fan cooled Magnum 6K32F / FR was designed for heavy duty Carrier class and Industrial applications that require high port density and secure devices which save in cost, rack space and run cool to provide long term reliability. This rack mountable managed switch comes with a wide variety of AC/DC options to deliver effective and efficient solutions tailored to specific industrial applications.

The fan-cooled 6K32F/FR Series have the same four modular configurable slots as the 6K32FC/FRC models and offer the same flexibility of configuration. (see above).

Figure 2.2.1b: 6K32F front view, configured for 2 RJ-45 Gigabit ports, 4 ST 100Mb FX ports, 8 MTRJ 100Mb FX ports and 8 LC 100Mb FX ports

The modular option with four slots exemplifies this managed switch’s extra capability to meet any 10, 100 or Gigabit requirement effectively, satisfying almost any demand for complex Ethernet networks. The bandwidth demand of Triple Play “voice- data-video” over Ethernet will be handled efficiently.

The growing demand of security and “Ease of use” are the other adding features of this managed switch. The switch allows the users to secure their network through port security, Radius X, Tacacs+ and Snmpv3 and provide an effective solution of ease of use through “Secure Web based management and scripts feature to manage the 6K32F switch remotely”. The 6K32F loaded with robust MNS-6K firmware is specially

www . GarrettCom . com

12

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

designed to meet the future demand of Ethernet requirements with cost-effective secure solutions. The Magnum 6K32F is also available in a Reverse model option, where the LEDs are on the front and the available ports along with the power supply area found on the rear side. This configuration is mostly used for the carrier-class market.

The modules which may be configured and used in the modular slots of the Magnum 6K32F Series are described here.

The Magnum 6K32F is preloaded with robust and intuitive MNS-6K Managed Network Software to handle industry-standard IEEE 802.1p QOS prioritization and nonblocking wire speed on all ports. It provides high performance switching services for both “smooth” streaming and “bursty” data traffic. For redundant LANs, it offers S-ring, RS-Ring, Link-Loss-Learn, STP and RSTP. Security features include SNMPv3, SSL/SSH, 802.1X, TACACS+, Port Security, and Tagged VLANs. See MNS-6K materials for further details about software.

2.2.2Eight-port SFF fiber modules (6KP8-MTRJ, 6KP8-MLC), 100Mb fiber

Fig.2.2.2 : SFF Fiber Port Modules, 6KP8-MTRJ (left) and

6KP8-MLC or -SLC (right)

In an eight-port SFF fiber port module, all of the fiber ports are of the same speed (100Mb), mode, and connector type. Models that are available with Small Form Factor (SFF) are multi-mode MT-RJ or LC-type connectors, and single-mode LC-type connectors.

The 100Mb fiber eight-port modules for the Magnum 6K32F Series normally are set (factory default) to operate in full-duplex mode for best fiber distance and performance. Using the 6K32F Series MNS software, the user may select fullor halfduplex mode per-port through the set-up of the software (See the Magnum MNS-6K Software Manual for the flexibility to adapt to any FDX or HDX type of Fast Ethernet devices).

There are three LED’s per fiber port. The Link (LK) LED indicates “ready for operation” on that port when lit, the F/H LED indicates operation in full-duplex mode

www . GarrettCom . com

13

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

when ON (half-duplex when OFF), and the blinking ACT LED indicates receiving Activity on the port. A fiber cable must be connected into a SFF port and the Link (LK) indicator for that port must be ON (indicating there is a powered-up device at the other end of the cable) in order for a LK LED to provide valid indications of operating conditions on that port.

2.2.3 Eight-Port Copper Module, 6KP8-RJ45 (MDIX)

The 6K-Series 8-port Copper port module, model 6KP8-RJ45, provides eight 10/100Mb switched RJ-45 ports. The 10/100Mb switched ports normally (as a default setting) are independently N-way auto-negotiating, and autocrossover(MDIX) for operation at 10 or 100Mb speed in fullor half-

duplex mode, i.e., each independently selects a mode and speed to match the device at the other end of the twisted pair cable.

(See Section 4.3 for auto-negotiation and MDIX details). The auto-crossover feature will automatically determine the other side of the connection to make the connection, and eliminate the need of a cross-over cable.

On the model 6KP8-RJ45 module, there are four LEDs for each port, two in the connector and two separate. The LK (Link) LED indicates “ready for operation” on that port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF (when auto-negotiation is not disabled). The FDX/HDX LED is ON to indicate full-duplex operation and OFF to indicate half-duplex mode. A twisted pair cable must be connected into an RJ-45 port and the Link (LK) indicator for that port must be ON (indicating there is a powered-up device at the other end of the cable) in order for a LK LED to provide valid indications of operating conditions on that port.

Using the 6K8-Series (MNS-6K) management software, the user may disable auto-negotiation and fix the desired operation of each RJ-45 port. User may select 10Mb or 100Mb speed and fullor half-duplex mode per-port as per user requirement. (See Magnum MNS-6K Software Manual for details info.).

www . GarrettCom . com

14

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

2.2.3a PoE(Power Inside), model PI6KP8-45RJ (MDIX), 8-port 10/100Mb

The New PoE RJ-45 ports act similar to regular RJ-45 ports, except they have capability of providing power on each port to power up the PD devices, per the IEEE802.3af PoE standard. Only 4 x RJ-45 (10/100) ports max. support POE(Power Inside) option in one rack mounted 6K-unit. The power inside PoE option is factory configured and equipped with the necessary power option to support four 802.3af PoE pd devices. The 4-RJ45 POE module are also available with mix –n-match with fiber modules. Please check the ordering information Sec.1.2. for all the various PI6K PoE modules option.

The LEDs on 6KP8-RJ45- PoE module are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when connected properly to an 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE.

LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK/ACT, as shown in the diagram.

2.2.3b PoE(Power Pass-through), model P6KP8-RJ45 (MDIX), 10/100Mb 8-port

The PoE (Power-pass-through) RJ-45 ports act similar to regular RJ-45 ports, except they have capability of providing power on each port to power up the PD devices, per the IEEE802.3af PoE standard. The Power Pass-through PoE modules are totally dependent upon the powerful -48VDC input power supply to support more RJ-45 (10/100) ports. Each port requires at least 15watts to power up the PoE PD devices max. One PoE module can be configured in the A, B, C or D slot of any 6K s with

-48vdc power input. The PoE modules are also available with mix & match fiber

www . GarrettCom . com

15

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

modules. Please check the ordering information Sec.1.2 for all the various P6K PoE modules option.

The LEDs on 6KP8-RJ45- PoE module are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when connected properly to an 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE.

LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK/ACT, as shown in the diagram.

2.2.4Six-Port “4 + 2”Combo Modules,

4@ 10/100 RJ-45 and 2@100Mb fiber (ST or SC)

The combo six-port modules are combinations of copper and fiber media, available as four 10/100 switched RJ-45 copper ports and two 100Mb switched multimode fiber ST, SC or single mode SC or Long Reach SC ports. For ports numbering, ports 1,3,5,7 are copper, ports 2 and 6 are fiber, ports 4 and 8 are not present.

The four RJ-45 ports operate just like the 8-port copper module with the autocross (MDIX) feature to eliminate the use of cross-over cables, and the two fiber ports operate at 100Mbps full-duplex (default). User mode control per port through the MNS software is also the same.

On Magnum “4+2” Combo modules, there are four LED’s for each RJ-45 port, which indicate status the same as described for the 6KP8-RJ45 in Section 2.2.3 above. The fiber port’s LEDs indicate status the same way as described for the SFF fiber modules in Section 2.2.2 above. Color-coding on the panel of the module shows which LEDs belong to which port.

The Magnum Combo six-port modules are also available with 4@ MTRJ 100Mb mm SFF fiber and 2@10Mb fiber mm ST ports, and with 4@ RJ45 10/100 copper and 2@10Mb fiber mm ST ports.

The 4@ RJ-45 + 2@ 10 Mb ST operation of the SFF fiber and the RJ-45 half of the module is as described for those port types above. For detailed information about 10Mb mm ST fiber half of the module, see Section 2.2.5.

www . GarrettCom . com

16

Magnum 6K32F/FR/FC/FRC Managed Switch Installation and User Guide (05/08)

2.2.5Four-Port 10 Mb mm Fiber ST Modules

The 4port @10Mb ST fiber modules behave the same as the 8@100Mb ST fiber modules except for the 10Mb speed. For port numbering, ports 1, 2, 5, 6 are present, ports 3, 4, 7, 8 are not present. The default setup on the 10Mb fiber module is halfduplex, which allows the Magnum 6K32F Series Switch to connect to any 10Mb hub or media converter or almost any other device with a 10Mb fiber Ethernet port. User mode control per port through the MNS software is the same as the other 6K32F Series modules. The fiber ports support fiber cabling distances according to the 10BASE-FL standard, i.e., 2km distance for multi-mode fiber. (Single-mode for up to 10Km distance may be available as a special order configuration).

2.2.6Gigabit (1000Mbps) port modules

The Magnum 6K32F Series switches offer wide options for Gigabit speed with multiple choices for the modular slot. The new Magnum 6K32F Series can be configured with eight Gigabit ports (copper or Fiber) maximum. The Gigabit port option for the modular slot comes in a couple of different configurations. The two Gigabit port modules have been offered as GBPM-2OTX (fiber or RJ-45), whereas the single Gigabit module comes in flavors of G+4(10/100 RJ-45 ports) or G+2 (100Mb fiber ports) as shown below in the figure.

1@ 1000Mb Fiber SC + 2@ 100Mb SC

1@ 1000Mb Fiber SC + 4@10/ 100Mb

The 6K32F Series modules provide a GBIC opening for insertion of industry-standard GBICs to provide Gigabit (Gb) media flexibility. GBIC models are available for both multi-mode (550m) and single-mode (10, 25, 40, 70, 120)km fiber options, and for Gigabit copper as well with new models appearing often.

www . GarrettCom . com

17

Loading...
+ 52 hidden pages