Frigidaire CFPWD15A, CFPWD15W User Manual

0 (0)

Installation Instructions

15” Pedestal

Instructions d’installation

Socle de 38 cm (15 po)

Instrucciones de Instalación

Pedestal de 15" (38,1 cm)

27”

(68.

 

5

cm)

 

15”

(38

cm)

 

 

.5”

26

(67

cm)

 

42.5” cm) (108

GREEN KIT COMPONENTS:

A

2

Front brackets.

A

B

2

Rear brackets.

 

COMPOSANTS DU NÉCESS. VERT:

 

A

2 supports avant.

B

B

2 supports arrière.

PIEZAS DEL KIT VERDE:

A 2 soportes delanteros.

B 2 soportes traseros.

SCREW KIT COMPONENTS:

C 14 #10 (16 x .500) screws.

COMPOSANTS DU NÉCESSAIRE DE VIS: C

C 14 vis n° 10 (16 x .500).

PIEZAS DEL KIT (TORNILLOS):

C 14 tornillos n.º 10 (16 x .500).

Total weight IN closed drawer or combination of IN and ON TOP OF open drawer should not exceed 65 lb. (29.5 kg).

Le poids total DANS un tiroir fermé ou une combinaison du poids DANS et SUR le tiroir ouvert ne doit pas excéder 29,5 kg (65 lb).

 

 

 

 

 

 

 

 

El peso total DENTRO del cajón cerrado o el peso

 

 

137333700 A (1002)

 

 

 

 

 

 

 

combinado de los artículos que estén DENTRO y ENCIMA del cajón

 

 

 

abierto no debe exceder las 65 lb (29,5 kg).

 

 

 

 

 

 

 

 

 

Tools needed: / Outils nécessaires: /

Herramientas necesarias:

 

 

 

 

 

OR

OR

 

 

 

AND

 

 

AND

 

 

 

 

 

 

 

 

 

OU

OU

 

 

 

ET

 

 

ET

 

 

O

O

9/16” or 14 mm box wrench

Y

Phillips screwdriver

Y

 

 

Optional universal

Adjustable wrench

 

 

 

 

wrench available

Clé à molette

Clé polygonale de

 

 

 

 

 

 

from dealer

 

Tournevis Phillips

 

Carpenter’s level

 

Clé universelle

Llave ajustable

9/16 po ou de 14 mm

 

Destornillador Phillips

 

Niveau de charpentier

 

Llave de cubo de

 

 

 

optionnelle (en vente

 

 

 

 

 

 

 

chez le détaillant)

 

9/16 po o 14 mm

 

 

 

 

Nivel de carpintero

 

Llave universal opcional

 

 

 

 

 

 

 

 

 

 

(disponible a través

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

de su distribuidor local)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

 

AVERTISSEMENT

 

ADVERTENCIA

Failure to disconnect from power source before stacking could result in personal injury or even death.

Improper installation of dryer venting could result in personal injury or damage to property.

To avoid back or other injury, have more than one person move or lift the washer or dryer.

Do not stack a dryer on top of washer already installed on pedestal.

English continued on page 2.

Ne pas débrancher l’appareil de sa source d’alimentation en électricité avant de le superposer peut causer des blessures, voire la mort.

Une installation inappropriée du système de ventilation de la sécheuse peut causer des blessures ou des dommages matériels.

Pour éviter les blessures au dos ou d’autres types de blessure, demandez l’aide d’autres personnes pour déplacer ou soulever la laveuse ou la sécheuse.

Ne superposez pas une sécheuse sur une laveuse déjà installée sur un socle.

Pour la suite de la version française, reportez-vous à la page 5.

El no desconectar el suministro eléctrico antes de la instalación apilada puede ocasionar lesiones personales o incluso la muerte.

La instalación inadecuada de la ventilación de la secadora puede ocasionar lesiones personales o daños a la propiedad.

Para evitar lesiones en la espalda u otro tipo de lesiones, procure levantar o mover la lavadora o secadora con la ayuda de más de una persona.

No apile la secadora sobre la lavadora si ya está instalada sobre un pedestal.

La versión en español continúa en la página 8.

1

Prepare appliance for mounting

Due to higher center of gravity of appliance on pedestals, some side-to-side rocking is normal during operation. Vibration can be minimized by assuring appliance is installed properly, including being level and solid on all four (4) legs by following these directions.

1.If washer or dryer is new and has not been installed yet, skip to step 4.

2.If dryer is already installed, disconnect dryer from electrical and gas connections and exhaust venting.

3.If washer is already installed, disconnect washer from electrical connection. Turn off hot and cold water supply and disconnect hot and cold water supply hoses from water supply outlets.

Disconnect drain hose from drain pipe. Remove hole plugs from back sheet and reinstall shipping braces and bolts.

4.Protect floor and unit with cardboard or rug and carefully lay the appliance on its side and screw each leg completely into the base.

- EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the appliance.

DO NOT use open dispenser drawer of washer or dispenser cavity as hand-hold location when tipping washer on its side. Serious damage could occur to your washer.

If feet are not completely screwed in, mounting holes in appliance will not align to mounting holes in brackets.

5.If appliance has metal feet with a locking nut, unscrew them, remove the locking nut and reinstall the feet flush to the base.

If locking nuts are not removed on units with metal feet, mounting holes in appliance will not align to mounting holes in brackets.

Prepare pedestal before mounting

1.Locate pedestal

to within a few DO NOT remove foam! inches of its

final location.

Allow for approximately 5 in. (12.5 cm) behind the pedestal for clearance of back of washer or dryer to the wall. Allow additional space if venting dryer upward or downward.

2. Level the pedestal front-to-back and side-to-side by adjusting each leveling leg. Keep leg extension to a minimum.

adjustable pliers

raise lower

3.Rock the pedestal from corner-to-corner to check for stability. Repeat leveling and rocking until all four (4) feet are sturdy on the floor and pedestal is level.

4.Without turning the rubber foot, lock each pedestal leg in place by tightening its lock nut tight against the pedestal base.

lock nut

2

Frigidaire CFPWD15A, CFPWD15W User Manual

Attach front mounting brackets

1. Attach each front clip to outer-most set of holes with 2 screws.

Front brackets from

DRAWER

GREEN kit.

 

Attach rear mounting brackets

• Each rear bracket has tabs marked “A” and “B”.

TAB B

TAB A

Each pedestal has slots in the rear marked “1”, “2” and “3”.

SLOT 1

SLOT 2

SLOT 3

Each rear bracket also has 2 arrows indicating bracket direction when mounted on the pedestal.

DIRECTION

INDICATOR

ARROWS

1.Determine your appliance type (washer or dryer) and style of side panel according to columns 1 and 2 in table below.

2.Orient rear brackets according to column 3 for your particular model.

3.Attach each bracket with 2 screws through the holes that line up on pedestal.

1 - Appliance

2 - Side panel style of your appliance

3 - Rear bracket orientation

DRYER

3 indents on side.

• Rear brackets from

 

 

 

 

 

GREEN kit

 

 

• Tab A into

 

 

Slot 1

 

 

• Arrow pointing to

 

 

 

back

DRYER

2 indents on

• Rear brackets from

 

side and 4 inch

 

 

GREEN kit

 

knockout for side

 

 

• Tab B into

 

venting.

 

Slot 3

 

 

 

 

• Arrow pointing to

 

 

 

front

WASHER

3 indents on side.

• Rear brackets from

 

 

 

 

 

GREEN kit

 

 

• Tab A into

 

 

Slot 2

 

 

• Arrow pointing to

 

 

 

back

WASHER

3 indents on side

• Rear brackets from

 

in shape of “lOl”.

 

 

GREEN kit

 

 

 

 

 

• Tab A into

 

 

Slot 1

 

 

• Arrow pointing to

 

 

 

front

3

Attach pedestal to appliance

1.Turn pedestal on its side to match orientation to appliance.

2.Slide pedestal up to appliance and line up holes in mounting brackets with holes in appliance base.

Special instructions for mounting a dryer with side pane style of 2 indents and 4 inch knockout (see image to right).

Rear bracket mounts to dryer with wide tabs on bracket into slots on rear of dryer.

SLOT in rear of dryer

Wide hook TAB on rear bracket

4.Using more than one person, carefully return appliance and pedestal to upright position.

- EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the appliance.

Engage hook tabs of rear bracket into slots of dryer before aligning front bracket with holes in dryer base.

Continue with instructions below for attaching front bracket to dryer base.

3.Attach rear and front brackets to appliance base with supplied screws into aligning holes - one in each front bracket and two in each rear bracket.

DO NOT use open dispenser drawer of washer or dispenser cavity as hand-hold location when tipping washer upright. Serious damage could occur to your washer.

5.After retuning appliance upright, loosen each mounting screw going into appliance base. Allow the appliance to settle in the brackets and retighten each mounting screw.

Installing or re-installing appliance

Washer on pedestal:

1.Slide washer/pedestal into place.

2.Check for levelness and rock all four (4) legs again. Repeat until level and solid.

3.Refer to Washer Installation Instructions for complete details on installing water, drain, or electrical.

Dryer on pedestal:

1.Slide dryer/pedestal into place.

2.Check for levelness and rock all four (4) legs again. Repeat until level and solid.

3.Refer to Dryer Installation Instructions for complete details on installing electrical, gas, or exhaust venting.

4

Loading...
+ 8 hidden pages