Frigidaire 220211A243 User Manual

Size:
987.75 Kb
Download

USE & CARE MANUAL

READ AND SAVE THESE INSTRUCTIONS

ELECTRONIC CONTROL AIR CONDITIONER

P/N 220211A243

ROOM AIR CONDITIONER WARRANTY

Your product is protected by this warranty

Your appliance is warranted by Electrolux. Electrolux has authorized Frigidaire Consumer Services and their authorized servicers to perform service under this warranty. Electrolux authorizes no one else to change or add to any of these obligations under this warranty. Any obligations for service and parts under this warranty must be performed by Frigidaire Consumer Services or an authorized Frigidaire servicer.

 

WARRANTY

FRIGIDAIRE, THROUGH ITS

THE CONSUMER WILL BE RESPONSIBLE

 

PERIOD

AUTHORIZED SERVICERS, WILL:

FOR:

 

 

 

 

FULL ONE-YEAR

One year from original

Pay all costs for repairing or replacing parts

Costs of service calls that are listed under

WARRANTY

purchase date.

of this appliance which prove to be defective

NORMAL RESPONSIBILITIES OF THE

 

 

in materials or workmanship.

CONSUMER.*

 

 

 

 

LIMITED 2-5YEAR

Second through fifth

Repair or replace any parts in the Sealed

Diagnostic costs and any removal,

WARRANTY (Sealed

years from original

Refrigeration System (compressor,

transportation and reinstallation costs which

System)

purchase date.

condenser, evaporator and tubing) proves to

are required because of service. Costs for

 

 

be defective in materials or workmanship.

labor, parts and transportation other than with

 

 

 

respect to the Sealed Refrigeration System.

 

 

 

 

LIMITED WARRANTY

Time periods listed

All of the provisions of the full and limited

Costs of the technician’s travel to the home

(Applicable to the State

above.

warranties above and the exclusions listed

and any costs for pick up and delivery of the

of Alaska)

 

below apply.

appliance required because of service.

 

 

 

 

* NORMAL RESPONSIBILITIES OF THE CONSUMER

EXCLUSIONS

IF YOU NEED SERVICE

This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below.

1. Proper use of the appliance in accordance with instructions provided with the product.

2.Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing, electrical and/or gas codes.

3.Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house wiring.

4.Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a part of the appliance when it was shipped from the factory.

5.Damages to finish after installation.

6.Replacement of light bulbs and/or fluorescent tubes (on models with these features).

This warranty does not cover the following:

1.CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

2.Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household use. The consumer shall pay for such service calls.

3.Damages caused by services performed by persons other than authorized Frigidaire servicers; use of parts other than Frigidaire Genuine Renewal Parts; obtained from persons other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4.Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order:

1.Contact Frigidaire Consumer Services or an authorized Frigidaire servicer.

2.If there is a question as to where to obtain service, contact our Consumer Relations Department at:

Frigidaire

CANADA

P.O. Box 212378

Electrolux Canada Group

Augusta, GA 30917

6150 McLaughlin Road

800-444-4944

Mississauga, Ontario L5R 4C2

1-866-213-9397

 

Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Electrolux.

This warranty applies only in the 50 states of the U.S.A., Puerto Rico and Canada.

FOR SERVICE CALL 1-800-444-4944.

2

2

Product Registration

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the serial plate is located on the outside of the cabinet.

Model No.

Serial No.

Register Your Product

The self-addressedPRODUCT REGISTRATION CARD should be filled in completely, signed and returned to the Frigidaire Company.

Contents

NOTE: This Owner’s Guide provides specific operating instructions for your model. Use the room air conditioner only as instructed in this Owner’s Guide. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

2Warranty

3Product Registration

3Normal Sounds

4 Important Safety Instructions

5-11Using Air Conditioner

5-11Air Conditioner Features

12 Care and Cleaning

12 Energy Saving Ideas

13 Avoid Service Checklist

Normal Sounds

High Pitched Chatter

Today’s high efficiency compressors may have a high pitched chatter during the cooling cycle.

Sound of Rushing Air

At the front of the unit, you may hear the sound of rushing air being moved by the fan.

Gurgle/Hiss

“Gurgling or hissing” noise may be heard due to refrigerant passing through evaporator during normal operation.

Vibration

Unit may vibrate and make noise because of poor wall or window construction or incorrect installation.

Pinging or Swishing

Droplets of water hitting condenser during normal operation may cause “pinging or swishing” sounds.

3

Important Safety

Instructions

The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire.

Please refer to the section ‘Operation of Current Device’ for details.

In the event that the power supply cord is damaged, it cannot be repaired it must be replaced with a cord from the Product Manufacturer.

Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord.

Grounding type wall receptacle

Do not, under any circumstances, cut, remove, or bypass the grounding prong.

Power supply cord with 3-pronggrounding plug and current detection device

Read all instructions before using this air conditioner.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings.

Prevent Accidents

To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following:

Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille.

If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first. If the window is a triple-tracktype with a screen panel included, remove the screen completely before installation.

Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual. Save this manual and the installation instructions for possible future use in removing or reinstalling this unit.

When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils.

Electrical Information

The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements.

Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-pronggrounding plug for protection against shock hazards.

Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle.

Do not run air conditioner with outside protective cover in place. This could result in mechanical damage within the air conditioner.

Do not use an extension cord or an adapter plug.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

Operation of Current

Device

Plug in & press RESET

The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following:

1.Plug in the Air Conditioner.

2.The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out.

3.Press the RESET button. Again you will notice a click as the button engages.

4.The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head).

NOTES:

Do not use this device to turn the unit on or off.

Always make sure the RESET button is pushed in for correct operation.

The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer.

If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer.

4

Air Conditioner Features ELECTRONIC CONTROL OPERATING INSTRUCTIONS

Before you begin, thoroughly familiarize yourself with the control panel and remote as shown

below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control alone or with the remote.

TURNS UNIT ON OR OFF

SETS

MODES

ENERGY

SAVER

MODE

SET TEMP.

 

ON

F

 

OFF

 

 

FAN SPEED

 

 

 

 

SET FAN

 

 

SPEEDS

Mode

Fan

 

Energy Saver

Timer

ACTIVATE

 

 

 

 

TIMERS

 

Cancel

 

Reset Lock

Clock

ADJUSTS

TEMP &

 

 

Sleep

Light

TIMES

 

Fig. “A” REMOTE CONTROL

 

 

SET TEMP.

 

ON

 

F

 

OFF

 

 

SETS

FAN SPEED

 

 

 

 

MODES

 

 

 

ENERGY

Mode

 

Fan

SAVER

 

 

Timer

MODE

Energy Saver

 

CLEAN AIR

Clean Air

 

Cancel

MODE

 

 

 

 

Follow Me

Reset Lock

Clock

REMOTE

Sleep

Light

SENSING/FOLLOW

 

 

 

ME MODE

TURNS UNIT

ON OR OFF

SET FAN

SPEEDS

ACTIVATE

TIMERS

ADJUSTS

TEMP &

TIMES

Fig. “B” REMOTE CONTROL w/DISPLAY & REMOTE SENSING/FOLLOW ME BUTTON

ADJUSTS TEMPERATURE OR TIME

ACTIVATES

TIMER

CHECK FILTER RESET BUTTON

SETS MODE

ENERGY SAVER MODE

DISPLAYS

TEMPERATURE/TIME

FAN SPEED

CLEAN AIR FEATURE (some models)

SLEEP MODE

.

SETS FAN SPEEDS

TURNS UNIT

ON OR OFF

REMOTE TEMP. SENSING INDICATOR (SOME MODELS)

UNIT CONTROL

Note: Please refer to separate remote control manual for additional operations.

Battery Size: AAA

Warning: do not mix old and new batteries. Do not mix alkaline, standard(carbon-zinc),or rechargeable(nickel-cadmium)batteries.

Note: The following instructions represent the Unit Control, the same instructions can be used for the Remote Control.

TO TURN UNIT ON:

YOU WILL SEE:

Note: The unit will turn on in the cool mode and high fan speed.

.

.

DO THIS:

PRESS ON/

OFF BUTTON

5

Air Conditioner Features

(continued)

TO CHANGE TEMPERATURE

SETTING:

 

DO THIS:

.

PRESS TO

 

RAISE

 

PRESS TO

 

LOWER

YOU WILL SEE:

72

.

Note: Tap or hold either up() or down() button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 62˚F (17˚C) and 86˚F (30˚C). If you want the display to read the actual room temperature. See “To Operate on Fan Only” section on Page 7.

TO ADJUST FAN SPEEDS:

YOU WILL SEE

 

THE SPEED CHOSEN:

 

 

88

 

 

LIGHT On

 

DO THIS:

 

.

PRESS FAN

.

 

 

 

BUTTON

 

 

SELECT

 

 

SPEED

 

TO USE AUTO TEMP FEATURE:

YOU WILL SEE:

 

 

72

LIGHT On

 

 

DO THIS:

 

Note: Fan starts at High Speed and adjusts to a slower speed

 

 

PRESS FAN

 

as the room temperature dictates. For example if the room

BUTTON

 

doesn’t get too warm, it will stay at the slowest speed. If the

.

.

room temperature rises quickly, such as a door being opened,

SELECT

 

 

it will automatically go to the highest speed. The fan speeds

AUTO TEMP

 

 

will re-adjustback to the slowest speed as the room returns to

 

 

 

 

the original set temperature. Press either the fan slower or fan

 

 

faster button to adjust the fan speed manually.

6

Air Conditioner Features

(continued)

TO USE DRY MODE:

 

DO THIS:

.

PRESS

 

MODE BUTTON

 

CHOOSE DRY

TO USE AUTO COOL:

 

DO THIS:

.

PRESS

 

MODE BUTTON

 

CHOOSE

 

AUTO COOL

YOU WILL SEE:

62

.

YOU WILL SEE

LIGHT On

Note: Use this mode when the room is already cool below 65oF (18oC) but the room is slightly humid.

72

LIGHT On

Note: In this mode when the room temperature is reached

the compressor will shut off and after a few minutes the fan

.

will switch to the lowest setting, (if a higher setting has been

originally selected). When the compressor switches back to

the cooling mode, then the fan speed will return to the original setting.

TO OPERATE ON FAN ONLY:

YOU WILL SEE:

72

DO THIS:

PRESS

MODE BUTTON

.

.

CHOOSE FAN

LIGHT On

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer.

During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode.

7

Air Conditioner Features

(continued)

TO USE THE ENERGY SAVER FEATURE:

YOU WILL SEE:

LIGHT On

72

 

 

Note: In this mode, the fan will continue to run for 3 minutes

 

DO THIS:

after the compressor shuts off. The fan then cycles on for 2

 

minutes at 10 minute intervals until the room temperature is

.

.

 

PRESS ENERGY

above the set temperature, at which time the compressor turns

 

back on and cooling stars.

 

SAVER BUTTON

 

 

TIMER: DELAY STOP / START

FEATURE

0.5

DO THIS:

 

PRESS

TIMER BUTTON

.

THEN

DO THIS:

PRESS

TEMP/TIMER

BUTTON

YOU WILL SEE: TIMER SETTING

LIGHT On

8.5

Note: For Delay Stop, the unit must be in the On position. Note: For Delay Start, the unit must be in the Off position.

To adjust timer setting, tap or hold the UP arrow(

) or the DOWN

arrow(

) to change delay timer at .5 hour increments, up to 10

.

hours, then at 1 hour increments up to 24 hours. The control will count

 

down the time remaining until start (8, 7.5, 7, etc.). The Delay Start

 

mode automatically selects cooling with maximum Fan Speed. The

 

temperature maintained will be the same as previously set. To change

 

the set temperature, press “COOL” then Up or Down arrows until the

 

desired temperature is indicated on the display. After 5 seconds, the

 

control will automatically change the display back to the hours re-

 

maining until the unit will start/stop. Turning the unit “ON” or “OFF” at

 

any time will cancel the Delay Start/Stop function.

 

The Delay Start/Stop Feature will work until the unit either starts or

 

stops. Once that happens the above steps have to be repeated again.

SLEEP FEATURE:

YOU WILL SEE:

88

88

.

.

DO THIS:

PRESS

SLEEP BUTTON

LIGHT On

Note: In this “MODE” the selected temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the “Sleep” MODE and the unit will continue to operate as originally programmed. The “Sleep” MODE program can be cancelled at any time during operation by again pressing the “Sleep” button.

8

Air Conditioner Features

(continued)

CHECK FILTER FEATURE: YOU WILL SEE:

LIGHT On

DO THIS:

AFTER CLEANING

PRESS CHECK

FILTER BUTTON

.

.

Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the “Check Filter” button and the light will go off.

CLEAN AIR FEATURE

YOU WILL SEE:

(on some models):

LIGHT On

 

 

 

Note: When this feature is “ON”, the electronic air purifier is

 

 

 

energized to remove pollen and impurities from the air. To cancel

.

DO THIS:

.

this feature, press the Clean Air button (the LIGHT will turn

 

off).

 

 

 

 

PRESS CLEAN

 

 

 

AIR BUTTON

 

 

REMOTE SENSING/FOLLOW ME FEATURE

(on some models) :

 

 

SET TEMP.

 

ON

 

 

F

OFF

 

 

 

FAN SPEED

 

 

Mode

 

 

Fan

Energy Saver

 

 

Timer

Clean Air

 

 

Cancel

Follow Me

Reset

Lock

Clock

DO THIS:

.

PRESS REMOTE

SENSING/FOLLOW ME

BUTTON ON

Sleep

Light

LIGHT pulsing On & Off intermittently.

 

SET TEMP.

ON

F

OFF

 

Note: Unit display shows

FAN SPEED

“set” temperature

 

Mode

 

 

Fan

Energy Saver

 

 

Timer

Clean Air

 

 

Cancel

Follow Me

Reset

Lock

Clock

Sleep

 

Light

NOTE: Remote display is actual temperature at remote control only.

Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode.

To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing button. Next, use the buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit itself). The

LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. It will con-tinueto send this signal until the feature is deactivated by pressing the remote sensing button. If the unit does not receive the remote sensingsignal during any 3 minute interval, the unit will beep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY. The unit display indicates the set temperature.

9

Air Conditioner Features

(continued)

FAULT CODES:

WARNING CODES:

If the display reads “AS” or “ED”, a sensor has failed. Contact your

Authorized Frigidaire Service Center.

In the fan mode if “LO” or “HI” is displayed, this means the room temperature is outside the unit set points of 99oF/37oC (HI) or 32oF/0oC (LO).

.

.

TO TURN UNIT OFF:

YOU WILL SEE

.

.

DO THIS:

PRESS ON/

OFF BUTTON

10

Air Conditioner Features

(continued)

ADDITIONAL THINGS YOU SHOULD KNOW

Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.

The “Cool “ circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.

The control will maintain the set temperature within 2 degrees Fahrenheit, between 62oF (17oC) and 86oF (30oC) degrees.

The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the other and back, press and hold the “TEMP/TIMER” Up ( ) and Down () buttons together for 3 seconds.

Fresh Air Vent Control (On some models)

The Fresh Air Vent allows the air conditioner to:

1.Recirculate inside air - Vent Closed (see Fig. 1)

2.Draw fresh air into the room - Vent Open (see Fig. 2)

3.Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open (see Fig. 3)

Figure 1 (VENT CLOSED)

Figure 2 (VENT OPEN)

Figure 3 (VENT & EXHAUST)

Air Directional Louvers

Air directional louvers control air flow direction. Your air conditioner has the louver type described below.

Auger Type

(8-WAY)

The louvers will allow you to direct the air flow Up or Down and Left or Right throughout the room as needed. Rotate the Auger Wheels until the desired Left/Right direction is obtained. Pivot horizontal louvers until the desired Up/Down direction is obtained.

11

Care and Cleaning

Energy Saving Ideas

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils.

Push the vent handle to the Vent Closed position (where applicable).

Open the front panel.

Grasp the filter by the center and pull up and out.

Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry before replacing.

Or, instead of washing you may vacuum the filter clean.

Cabinet Cleaning

Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-freecloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry.

Never use harsh cleaners, wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner.

Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton.

Do not block air flow inside with blinds, curtains or furniture; or outside with shrubs, enclosures, or other buildings.

The capacity of the room air conditioner must fit the room size for efficient and satisfactory operation.

Install the room air conditioner on the shady side of your home. A window that faces north is best because it is shaded most of the day.

Close the fireplace damper, floor and wall registers so cool air does not escape up the chimney and into the duct work.

Keep blinds and drapes in other windows closed during the sunniest part of the day.

Clean the air filter as recommended in the section “Care and Cleaning.”

Proper insulation and water stripping in your home will help keep warm air out and cool air in.

External house shading with trees, plants or awnings will help reduce the air conditioner’s work load.

Operate heat producing appliances such as ranges, washers, dryers and dishwashers during the coolest part of the day.

12

Avoid Service Checklist

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workman-shipor materials in this appliance.

OCCURRENCE

SOLUTION

Air conditioner will not operate.

Wall plug disconnected. Push plug firmly into wall outlet.

Plug Current Device Tripped. Press the RESET button.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFF. Turn Control ON and set to desired setting.

Air from unit does not feel cold enough.

Room temperature below 62°F (17°C). Cooling may not occur until room temperature rises above 62°F (17°C).

Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.

Reset to a Lower temperature.

Compressor shut-offby changing modes. Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode.

Air conditioner cooling, but room is too warm - ice forming on cooling coil behind decorative front.

Outdoor temperature below 62°F (17°C). To defrost the coil, set FAN ONLY Mode.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY Mode.

Temperature is set too Low for night-timecooling. To defrost the coil, set to FAN ONLY Mode. Then, set Temperature to a Higher setting.

Air conditioner cooling, but room is too warm - NO ice forming on cooling coil behind decorative front.

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature is set too High. Set temperature to a Lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit.

Doors, windows, registers, etc. open - cold air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling, floor and furniture.

Air conditioner turns on and off rapidly.

Dirty air filter - air restricted. Clean air filter.

Outside temperature extremely hot. Set FAN speed to a faster setting to bring air past cooling coils more frequently.

Noise when unit is cooling.

Air movement sound. This is normal. If too loud, set to a slower FAN setting.

Window vibration - poor installation. Refer to installation instructions or check with installer.

Water dripping INSIDE when unit is cooling.

Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to installation instructions - check with installer.

Water dripping OUTSIDE when unit is cooling.

Unit removing large quantity of moisture from humid room. This is normal during excessively humid days.

Remote Sensing Deactivating

• Remote control not located within range. Place remote control within 20 feet & 180°, radius of the front of the

Prematurely (Some Models).

 

unit.

 

• Remote control signal obstructed. Remove obstruction.

 

 

 

Room Too Cold.

• Set temperature too low. Increase set temperature.

 

 

Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote

 

 

control or deactivate remote sensing.

If These Solutions Fail, Call 1-800-444-4944For Frigidaire Service.

13